D Link 2002060010-1 IEEE 802.11b Wireless PCI Card User Manual
D Link Corporation IEEE 802.11b Wireless PCI Card
D Link >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 335971 |
| Application ID | yhOaOjiXc4ozobTbUfp15w== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 222.19kB (2777314 bits) |
| Date Submitted | 2003-06-27 00:00:00 |
| Date Available | 2003-06-27 00:00:00 |
| Creation Date | 2003-06-23 09:41:45 |
| Producing Software | Acrobat Distiller 5.0 (Windows) |
| Document Lastmod | 2003-06-23 09:41:45 |
| Document Title | User Manual |
DWL-520 2.4 GHz Wireless PCI Adapter Manual Rev. 032003 Building Networks for People Contents Package Contents .................................................... 3 Introduction............................................................... 4 Wireless Basics ........................................................ 6 Getting Started ......................................................... 9 Installation .............................................................. 16 Using the Configuration Utility for Windows 2000, 98, or ME ...................................................................... 32 Using the Configuration Utility for Windows XP...... 38 Networking Basics .................................................. 48 Troubleshooting ...................................................... 80 Technical Specifications ......................................... 84 Regulatory Statement............................................. 86 Package Contents Contents of Package: • DWL-520 2.4 GHz Wireless PCI Adapter • Manual, Quick Installation Guide, and Drivers on CD If any of the above items are missing, please contact your reseller. System Requirements: • A desktop computer with an available 32-bit PCI Card slot • Windows XP, Windows 2000, Windows ME, or Windows 98 SE • At least 32 MB of memory and a 300 MHz processor or higher • An 802.11b Access Point (e.g., WAP-B11 for Infrastructure Mode) or another 802.11b wireless adapter (e.g., WCB-B13 for Ad-Hoc mode.) Introduction The DWL-520 Wireless PCI Adapter is an advanced IEEE 802.11b compatible, high performance, wireless adapter that supports data transfer speeds of up to 11 Mbps. It is an ideal way to connect your laptop computer to a Wireless Local Area Network (WLAN.) After completing the steps outlined in the Quick Installation Guide you will have the ability to share information and resources, such as files and printers, and take full advantage of a “connected” environment for work or play! Please look at our Getting Started section in this manual. You will see several options for setting up a network using the DWL-520. The DWL-520 comes with software drivers for the most popular Microsoft Windows operating systems and can be integrated into a larger network running Windows XP, Windows 2000, Windows ME, and Windows 98SE, in either Ad Hoc mode (without an Access Point) or Infrastructure mode (with an Access Point.) This manual provides a quick introduction to wireless technology and its application as it relates to networking. Take a moment to read through this manual and get acquainted with wireless technology. Product Features • • • Compatible with IEEE 802.11b high rate standard to provide wireless Ethernet speeds of 11Mbps data rate Ethernet speeds of 11Mbps data rate Dynamic date rate scaling at 11, 5.5, 2 and 1Mbps Maximum reliability, throughput, and connectivity with automatic data rate switching • Supports wireless data encryption with 64- and 128-bit WEP standard for security • Integrated microstrip antenna • One-piece PC Card design to fully support PC Card type II defined mechanical and environmental stress conditions • Drivers support Windows 98SE, Windows ME, Windows NT, Windows 2000, and Windows XP • Simple user setup and diagnostics utilities • Compliant with FCC Part 15.247 for US, EN 300 328 for Europe, and RCR STD-33A and ARIB STD-T66 for Japan LEDS LED stands for Light-Emitting Diode. The DWL-520 Wireless PCI Adapter has two LEDs: Link and Activity. Wireless Basics Wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home or business. Strictly adhering to IEEE 802.11b, our wireless family of products will allow you to access the data you want, when and where you want it. No longer will you be limited to one location or forced to run new wiring through your home or office. You will be able to enjoy the freedom that wireless networking delivers. A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure has proven to be beneficial for many users. Wireless users can use the same network applications they use on an Ethernet LAN. Wireless adapter cards used on laptop and desktop systems, support the same protocols as Ethernet adapter cards. For most users, there is no noticeable functional difference between a wired Ethernet desktop computer and a wireless computer equipped with a wireless adapter other than the added benefit of the ability to roam within the wireless-cell. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Access Point (AP) is a device used to provide this link. People use wireless LAN technology for many different purposes. Mobility - Productivity increases when people have access to data in any location within the operating range of the WLAN. Ad-hoc management decisions based on real-time information can significantly improve worker efficiency. Low Implementation Costs - WLANs are easy to set up, manage, change and relocate. Networks that frequently change, both physically and logically, can benefit from WLANs’ ease of implementation. WLANs can operate in locations where installation of wiring may be impractical. Furthermore, IEEE standardization mandates interoperability of all WLAN devices that conform to the 802.11b set of standards. Installation Speed and Simplicity - Installing a wireless LAN system can be fast and easy and can eliminate the need to pull cable through walls and ceilings. Wireless Basics (continued) Installation Flexibility - Wireless technology allows the network to go where wires cannot go. Reduced Cost-of-Ownership - While the initial investment required for wireless LAN hardware might be higher than the cost of wired LAN hardware, overall installation expenses and life-cycle costs will be significantly lower. Long-term cost benefits are greatest in dynamic environments requiring frequent moves, adds, and changes. Scalability - Wireless LAN systems can be configured in a variety of topologies to meet the needs of specific applications and installations. Configurations are easily changed and range from peer-to-peer networks suitable for a small number of users to full infrastructure networks of thousands of users that allow roaming over a broad area. Wireless LAN products include: 802.11b 2.4 GHz Wireless Cardbus Adapters used with laptop computers (WCB-B13) 802.11b 2.4 GHz Wireless PCI cards used with desktop computers (DWL-520) 802.11b 2.4 GHz Wireless Access Points (WAP-B13) Standards-based Technology Based on the IEEE 802.11b standard, the DWL-520 is also interoperable with existing compatible 2.4 GHz wireless technologies, with data transfer speeds of up to 11 Mbps. Installation Considerations The DWL-520 lets you access your network with your laptop computer from virtually anywhere you want. Keep in mind, however, that the number and thickness of walls, ceilings or other objects that the wireless signals must pass thru may limit range. Typical ranges vary depending on the types of materials and background RF noise in your home or business. The key to maximizing range is to follow these basic principles: 1. Keep the number of walls and ceilings between the Access Point and your receiving device to a minimum – each wall or ceiling can reduce your wireless product’s range from 3-90 feet (1-30 meters.) For some businesses or for a large residential home deployment, it may be Wireless Basics (continued) beneficial to have more than one access point with overlapping coverage. 2. Be aware of the direct line between Access Points and computers with wireless adapters - A wall that is 1.5 feet thick (.5 meters), at a 45degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Try to make sure that the Access Points and Adapters are positioned so that the signal will travel straight through a wall or ceiling for better reception. 3. Building Materials make a difference - A solid metal door or aluminum studs may have a negative effect on range. Try to position Access Points, and computers with wireless adapters so that the signal passes through drywall or open doorways and not other materials. 4. Make sure that the antenna is positioned for best reception by using the software signal strength tools included with your product. 5. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate extreme RF noise. For the average residence, range should not be a problem. If you experience low or no signal strength in areas of your home that you wish to access, consider positioning the Access Point in a location directly between the computers with wireless adapters that will be connected. Additional Access Points can be connected to provide better coverage in rooms where the signal does not appear as strongly as desired. Using radio frequency (RF) technology, WLANs (Wireless Local Area Networks) transmit and receive data over the air, minimizing the need for wired connections. Thus, WLANs combine data connectivity with user mobility, and, through simplified configuration, enable movable LANs. Getting Started To begin, select the type of wireless network you will be building. We will discuss the following types of networks in this section: 1. A Home Internet Network with A Residential Gateway/Router 2. A Home Internet Network with Multiple IP Addresses 3. An Ad Hoc Network 4. An Ad Hoc Network with Internet Sharing Please select, from the four types of networks described above, the type of network that is appropriate for your needs. Please follow the instructions in the corresponding section that follows. 1. A Home Internet Network with A Residential Gateway/Router (Network administrators with Dynamic IPs can also follow these instructions.) If you have two or more computers (laptops or desktops) and want to share files, printers, and Internet access using a DHCP-capable Residential Gateway/Router – or - if you want to connect to an Ethernet network that uses Dynamic (DHCP) IP addresses, then follow the instructions on the next page. When it is complete, your network may look similar to this: DHCP stands for Dynamic Host Configuration Protocol. It is a protocol for assigning dynamic IP addresses “automatically.” With a DHCP-capable gateway, there is no need to manually assign an IP address. 1. A Home Internet Network with A Residential Gateway/Router (continued) (Requirements: A Residential Gateway/Router connected with an Ethernet (CAT5) cable to an 802.11b Access Point such as the WAP-B11. This type of installation requires that you provide a dynamic IP address for each computer on your network. You will need a DHCP-capable Residential Gateway/Router for your network. To complete the installation, please follow these steps: 1. Connect the Router/Gateway to a Broadband connection, (e.g., a Cable modem or a DSL modem.) 2. Connect the 802.11b Access Point (WAP-B11) to the router. 3. Install the DWL-520 Wireless PCI Adapter into a desktop computer on your wireless network. 4. Check the Device Manager to confirm that the wireless adapter is installed correctly. Please refer to the Networking Basics section in this manual entitled: Checking the Installation of the Drivers for the Wireless Adapter. 5. By default, the wireless adapter is set to obtain a Dynamic IP Address. If you are having difficulty connecting, check to make sure that the IP Address of the wireless adapter is within the IP address range of your network. Please refer to the Networking Basics section in this manual entitled: Checking The IP Address. 6. Learn to share printers and files. Please refer to the Networking Basics section in this manual entitled: Adding and Sharing Printers in Windows XP. 2. A Home Internet Network with Multiple IP Addresses (Network administrators with Static IPs can also follow these instructions.) If you have two or more computers (laptops or desktops) and want to share files, printers, and Internet access using multiple IP addresses that you have purchased from your Internet Service Provider -or- you want to connect to an Ethernet network that uses Static IP Addresses, then follow the instructions on the next page. When you have completed your network, it should look similar to this: 2. A Home Internet Network with Multiple IP Addresses (continued) 10 Please note that this type of installation requires that your ISP (Internet Service Provider) provides you a static IP address for each computer and the Access Point on your network. Please refer to the manual that came with your Access Point to determine its configuration. Please follow these steps to complete the installation: 1. Connect the Wireless Access Point to a Broadband connection (i.e., a Cable modem.) 2. Install the DWL-520 Wireless PCI Adapter into the desktop computer(s) on your wireless network. (You can also install the WCB-B13 Wireless Cardbus Adapter into your laptop computers.) 3. Check the Device Manager to confirm that the wireless adapter is installed correctly. Please refer to the Networking Basics section in this manual entitled: Checking the Installation of the Drivers for the Wireless Adapter. 2. A Home Internet Network with Multiple IP Addresses (continued) 4. Set the Static IP Address of the wireless adapters. Please refer to the Networking Basics section in this manual entitled: Assigning an IP Address. Note: The IP Address for all computers must be in the same IP Address range, and the Subnet Mask must be the same for all the computers on the network. For example: If the first computer is assigned an IP Address of 192.168.0.2 with a Subnet Mask of 255.255.255.0, then the second computer can be assigned an IP Address of 192.168.0.3 with a Subnet Mask of 255.255.255.0, etc. If you are using a PPPoE client (Point to Point Protocol over Ethernet) please contact your ISP (Internet Service Provider) for further instructions regarding connecting to the Internet. 5. Learn to share printers and files. Please refer to the Networking Basics section in this manual entitled: Adding and Sharing Printers in Windows XP. 3. An Ad Hoc Network If you have two or more computers (desktops or laptops) and want to share files and printers, but no Internet connection, please complete the following instructions. When your Ad Hoc network is complete it may look similar to this: 12 3. An Ad Hoc Network (continued) To complete this installation, please follow these steps: 1. Install the DWL-520 Wireless PCI Adapter into your desktop computers. (You may install the WCB-B13 Wireless Cardbus Adapters into your laptops - please refer to the Quick Installation Guide for further instructions.) 2. Set the Static IP Address of the wireless adapters. Please refer to the Networking Basics section in this manual entitled: Assigning an IP Address. Note: The IP Address for all computers must be in the same IP Address range, and the Subnet Mask must be the same for all computers on your network. For example: If the first computer is assigned an IP Address of 192.168.0.2 with a Subnet Mask of 255.255.255.0, then the second computer can be assigned an IP Address of 192.168.0.3 with a Subnet Mask of 255.255.255.0, etc. 3. Check the Device Manager to confirm that the wireless adapter is installed correctly. Please refer to the Networking Basics section in this manual entitled: Checking the Installation of the Drivers for the Wireless Adapter. 4. Check the Wireless Configuration for each wireless adapter. Please refer to the Networking Basics section in this manual entitled: Checking the Wireless Configuration. 5. Learn to share printers and files. Please refer to the Networking Basics section in this manual entitled: Adding and Sharing Printers in Windows XP. 4. An Ad Hoc Network with Internet Sharing If you have two or more computers (desktops or laptops) and want to share files, printers, and Internet access using one computer or laptop as an Internet Server, then follow the instructions below. When you have completed your network, it should look similar to this: 4. An Ad Hoc Network with Internet Sharing (continued) DFE-530TX To share an Internet connection with Internet Sharing software you will need to purchase Internet Sharing software or use the Internet Connection Sharing (ICS) utility provided with Windows XP, Windows 2000, Windows ME or Windows 98SE. Please follow your software documentation to properly configure the Internet sharing software after you install your wireless networking adapters. To install your wireless network adapter follow the instructions on the next page. If the Internet Sharing Software will be installed on the same computer into which you are installing this wireless network adapter, then follow these steps: 14 1. Install the DWL-520 Wireless PCI Adapter (please refer to the Quick Install Guide.) 2. Check the Device Manager to confirm that your adapter is installed correctly. Please refer to the Networking Basics section in this manual entitled: Checking the Installation of the Drivers for the Wireless Adapter. 3. Install your Internet Sharing Software 4. If required by the ICS software, set the static IP Address for the wireless adapter. Please refer to the Networking Basics section in this manual entitled: Assigning an IP Address. Note: The IP Address for all the computers on the network must be in the same IP Address range, and the Subnet Mask must be the same for all the computers on the network. For example: If the first computer is assigned an IP Address of 192.168.0.2 with a Subnet Mask of 255.255.255.0, then the second computer can be assigned an IP address of 192.168.0.3 with a Subnet Mask of 255.255.255.0, etc. 5. Learn to share printers and files. Please refer to the Networking Basics section in this manual entitled: Adding and Sharing Printers. If the Internet Sharing Software will be installed on a computer other than the one in which you are installing the DWL-520 Wireless PCI Adapter, then follow these steps: 1. Install the DWL-520 Wireless PCI Adapter into the computer (please refer to the Quick Install Guide.) 2. Check the IP Address for the wireless adapter. Please make certain that all the computers on your network are in the same IP Address range. Please refer to the Networking Basics section in this manual entitled: Checking your IP Address. Note: By default, the wireless adapter is set to obtain a Dynamic IP Address, automatically. 3. Learn to share printers and files. Please refer to the Networking Basics section in this manual entitled: Adding and Sharing Printers in Windows XP. Installation This section shows you how to install the Utility if you are using Windows 2000, 98, ME, or NT operating systems. Follow the instructions given below on how to install the hardware (DWL-520 PCI Adapter) and then the software (driver and utility). For those using Windows XP, the installation procedure will be the same until the utility installation. Windows XP has a built in utility for wireless devices. The configuration utility does not need to be installed for users using the XP operating system. System Requirements: • A desktop computer with an available 32-bit PCI Card slot • At least a 300 MHz processor and 32 MB of memory • PCI Controller properly installed and working • An 802.11b Access Point (for Infrastructure Mode) or another 802.11b wireless adapter (for Ad-Hoc mode.) 1. Installing the DWL-520 • • Turn on the computer Insert the DWL-520 Wireless PCI Adapter into an available 32-bit Cardbus PC Card slot. 16 2. Installing the Driver Installing the software involves two steps. The first is to install the Driver and the second is to install the Configuration Utility. • When the DWL-520 has been inserted into a 32-bit PCI slot, the Found New Hardware Wizard screen appears. • Continue with the installation and the screen below should appear. Click on Next to proceed with the installation. Click Next • Insert the Driver CD into the CD-ROM drive. The Install Hardware Device Drivers window will appear. Click Next. Click Next • The installation will continue with the following screen. Click Next. Click Next 18 • • The following screen will appear. The installation will continue with the following screen. Click Next. Click Next • The installation will continue with the following screen. Click Yes. • The installation will finish with the following screen. Click Finish. Click Finish 20 3. Installing the Configuration Utility Look for the file named “Setup.exe” on the installation CD-Rom. Double-click on it to start the installation for the configuration utility. Setup.exe When this screen appears click Next. Click Next. To install to the folder C:\Program Files\NonBrand click Next. Otherwise click on Browse to choose an alternate location. Or Click Browse Click Next 22 Click Next to proceed with the utility installation. Click Next The Setup Status screen will appear like the one below: After the Utility has been successfully installed, InstallShield Wizard will prompt you to restart your computer. Select “Yes, I want to restart my computer now,” and click on Finish. This completes the Utility installation. Click Finish 24 3. Uninstalling the Configuration Utility To uninstall the configuration utility Programs WLAN Monitor Uninstall. simply click Uninstall under To uninstall the driver, right-click on My Computer. Left-click on Properties to bring up the System Properties screen. 26 Click on the Hardware tab. Click on Device Manager. 28 Click on Network adapters. Right-click on the “Wireless LAN Card (RTL8180)” icon. 30 Click on Uninstall. You will then receive a Confirm Device Removal screen. Click OK to complete the uninstallation. Using the Configuration Utility for Windows 2000, 98, or ME If you are using Windows 2000, 98, ME, or NT, the Configuration Utility program for the DWL-520 is called WLAN Monitor. Once you have installed WLAN Monitor (the configuration utility), you can read this section of the manual to find out how to monitor and configure your DWL-520 adapter using WLAN Monitor. Screenshots for this section have been taken in Windows 2000. There are four tabs in the WLAN Monitor Configuration Utility program. In this section we will describe the uses for each tab in the Configuration Utility window. To access WLAN Monitor once it has been installed, just right-click on the WLAN Monitor icon in the taskbar, and then click on Wireless Network. Under the Configuration Tab you will find a list of access points to which you may add or change connections. Configuration Tab 32 Using the Configuration Utility or ME (continued) for Windows 2000, 98, On the left side of the screen are Available WLANs which you may connect to by first selecting the WLAN (it will appear highlighted) and then clicking on Add. When you do so a screen like the one below will pop up: In the Wireless Network Properties screen you may change the name of the WLAN. You may also enter wireless network encryption keys by checking Network Authentication (Shared mode) or Data encryption. You may enter up to four keys of length 10 or 25 hexadecimal digits. You may also set one of the four keys as a default key. Click on IP Config to set the IP address, Subnet mask, and Default gateway manually instead of obtaining the IP address automatically through the Dynamic Configuration Host Protocol (DCHP) server. You may also set the DNS server address settings and WINS address settings. If the network you are using is a computer-to-computer network or ad hoc network, no access points are used. You may check the box “This is a computer to computer (ad hoc) network; no access points are used” to enable this option. Using the Configuration Utility or ME (continued) for Windows 2000, 98, On the Configuration Tab click on Refresh to call up all the available WLANs. On the right side of the screen is a list of Preferred WLANs. These are WLANs that have already been added to the wireless network. Click New to rename the WLAN and reset its properties. You will see the Wireless Network Properties screen as displayed previously when you click New. This is also the same screen that will appear when you click Properties on the right side of the Configuration Tab screen. Click Remove to remove the connection. On the right side of the screen you may click Move Up to move the selected WLAN up in the order it is displayed on the Preferred WLANs screen. You may click Move Down to move the selected WLAN down in the order in which it is displayed. The Advance button allows the user to set the WLAN type to connect: infrastructure and ad hoc network, infrastructure network only, or ad hoc network only. You may also automatically connect to non-preferred networks by checking the option. When you are done entering the settings and options for the wireless network click on OK, Cancel, or Apply. Ok places the settings into effect and closes the graphical user interface (GUI). Cancel makes all settings entered invalid. Apply places the settings entered into effect but does not close the GUI. 34 Using the Configuration Utility or ME (continued) for Windows 2000, 98, Under the Status Tab you will find information on the connection state, hardware information, and advanced state. Status Tab Information given under Connected State are the Connection status (connected or disconnected), SSID, Network type (infrastructure or adhoc), Wep Status (enabled or disabled), Speed (of the wireless connection), and Signal Strength (a colored bar shows the intensity of the radio signals in the network). Under Hardware Information the Media Access Control (MAC) address of the hardware (WLAN cardbus adapter) is given. The MAC address is a factory given address that cannot be changed. A Regulatory Domain displays the code of the country in which this software is being used. Advanced State shows the Radio Status (ON or OFF) and there is no Turbo Mode. Click OK to accept the connection status and exit the GUI. Click Cancel to not accept the status settings and exit the GUI. Using the Configuration Utility for Windows 2000, 98, or ME (continued) Under the Options Tab general settings and advanced settings are shown. Options Tab Check “Auto launch when Windows starts up” so that WLAN Monitor automatically launches when Windows starts up. Part of the GUI for WLAN Monitor is a mini status dialog box that appears when you left-click on the WLAN Monitor icon in the taskbar. “Remember mini status position” keeps track of the last position of the mini status dialog box. “Auto hide mini status” pulls the dialog box to the right and drags it off the screen. “Set mini status always on top” places the mini status dialog box on top of all other dialog boxes. Check “Enable IP Setting in Profile” to enable the IP settings made under IP Config in the Wireless Network Properties screen. If checked current IP settings will be saved. If unchecked (and previously checked) previous IP settings will be restored. Check “Disable Radio” to disconnect the network connection without removing the WLAN cardbus adapter. You may select the Current Chanel (1, 2, or 3) and Power Save Mode (Disable, Max Save, Fast Save). You may enter the Fragmentation Threshold and RTS Threshold. 36 Using the Configuration Utility for Windows 2000, 98, or ME (continued) The About Tab gives the utility version of WLAN Monitor. About Tab Using the Configuration Utility for Windows XP The WLAN Monitor Configuration Utility supports Windows XP; however, Windows XP has its own utility for wireless devices. In order to use the WLAN Monitor Configuration Utility as described in the last section you must disable the utility built into Windows XP by unchecking the box below. 38 Using the Configuration Utility (continued) for Windows XP If you leave the “Use Windows to configure my wireless network settings” box checked you will use the Windows XP utility for wireless devices. The following demonstrates how to manage wireless network connections with the Windows XP built-in utility. Creating a connection Right-click on “My Network Places” to obtain a drop-down menu with Properties listed. Using the Configuration Utility (continued) for Windows XP Left-click on Properties to obtain the Network Connections screen. 40 Using the Configuration Utility (continued) for Windows XP Right-click on the “Wireless Network Connection” icon to produce another drop-down menu with item Properties. Using the Configuration Utility (continued) for Windows XP Left-click on Properties to bring up the screen below. 42 Using the Configuration Utility (continued) Click on the Wireless Networks tab. for Windows XP Using the Configuration Utility (continued) for Windows XP Click on the Access Point under Available Networks with which you wish to establish a connection. • Click on Configure to establish a connection with the chosen access point “D-Link.” A screen such as the following called Wireless Network Properties will then appear. 44 Using the Configuration Utility (continued) for Windows XP Enter the appropriate settings and click OK. Using the Configuration Utility (continued) for Windows XP The access point “D-Link” has been added to the network under Preferred networks. 46 Using the Configuration Utility (continued) for Windows XP The Network Connections window now shows the wireless network connection as “Enabled”. Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, ME, or 98. Go to START>CONTROL PANEL>NETWORK CONNECTIONS Select Set up a home or small office network. When this screen appears, Click Next. 48 Networking Basics Please follow all the instructions in this window: Click Next. In the following window, select the best description of your computer. If your computer connects to the Internet through a gateway/router, select the second option as shown and Click Next. Networking Basics • • Enter a Computer description and a Computer name (optional) and Click Next. Enter a Workgroup name and Click Next. All computers on your network should have the same Workgroup name. 50 Networking Basics • Please wait while the wizard applies the changes. When the changes are complete, Click Next. • Please wait while the wizard configures the computer. This may take a few minutes. Networking Basics • In the window below, select the best option. In this example, “Create a Network Setup Disk” has been selected. You will run this disk on each of the computers on your network. Click Next. • Insert a disk into the Floppy Disk Drive, in this case drive “A:” Format the disk if you wish, and Click Next. 52 Networking Basics • Please wait while the wizard copies the files. • Please read the information under Here’s how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue Click Next. Networking Basics • Please read the information on this screen, then Click Finish to complete the Network Setup Wizard. • The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use. 54 Networking Basics Naming your Computer To name your computer, please follow these directions: In Windows XP: • Click START (in the lower left corner of the screen) • Right-click on My Computer • Select Properties and Click • Select the Computer Name Tab in the System Properties window. You may enter a Computer description if you wish, this field is optional. To rename the computer and join a domain, • Click Change Networking Basics Naming your Computer (continued) • In this window, enter the Computer name. • Select Workgroup and enter the name of the Workgroup. • All computers on your network must have the same Workgroup name. • Click OK Checking the Installation of the Drivers for the Wireless Adapter • Go to Start • Right-click on My Computer • Click Properties 56 Networking Basics Checking the Installation of the Drivers for the Wireless Adapter • Select the Hardware Tab • Click Device Manager • Click on Network Adapters • Right-click on Wireless LAN Card (RTL8180) • Select Properties to check that the drivers are installed properly Networking Basics Checking the Installation of the Drivers for the Wireless Adapter • Look under Device Status to check that the device is working properly. • Click OK Checking the Wireless Configuration • Double-click on the Networking Icon in the taskbar. 58 In this window you will see the Signal Strength and the Status of the DWL-520. In this case the Status and the Signal Strength are fine. For more information: • Click Properties Networking Basics Checking the Wireless Configuration • Click Configure to access more information. • Select Settings This screen shows the wireless configuration. • Click Modify to check on the configuration. 60 Networking Basics Checking the Wireless Configuration • The Network Name (SSID) should be set to Default. • The Network Connection should be set to the correct mode (Infrastructure or Ad Hoc.) • The Turbo Mode setting (Disabled in the example here) must be the same on all the stations in your network. • Click on the Security Tab • If Enable Security is selected on one station on your network, it must be selected on all stations. Likewise, if Enable Security is deselected on one station, it must be deselected on all stations. • Check to see that your IP Address and your Subnet Mask are in the correct range. See the Networking Basics sections: Checking the IP Address and Assigning a Static IP Address. Networking Basics Checking the IP Address in Windows XP • Right-click on the networking icon in the task bar • Click on Status The following window will display • Click the Support tab. • Click Close 62 Networking Basics Assigning a Static IP Address Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses. If you are not using a DHCP capable Gateway/Router, or you need to assign a Static IP Address, please follow these instructions: • Go to START • Double-click on Control Panel • Double-click on Network Connections Networking Basics Assigning a Static IP Address • Right-click on Local Area Connections. • Double-click Properties • Highlight Internet Protocol (TCP/IP) • Click Properties 64 Networking Basics Assigning a Static IP Address • Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window, • Input your IP address and subnet mask. (The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computers should have IP Addresses that are sequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must be the same for all the computers on the network.) • Input your DNS server addresses. (Note: If you are entering a DNS server address, you must enter the IP Address of the Default Gateway.) • Click OK The DNS server information will be provided by your ISP (Internet Service Provider.) You have completed the assignment of a Static IP Address. (You do not need to assign a Static IP Address if you have a DHCP-capable Gateway/Router.) Networking Basics Adding and Sharing Printers in Windows XP After you have run the Network Setup Wizard on all the computers in your network (please see the Network Setup Wizard section at the beginning of Networking Basics,) you can use the Add Printer Wizard to add or share a printer on your network. Whether you want to add a local printer (a printer connected directly to one computer,) share an LPR printer (a printer connected to a print server) or share a network printer (a printer connected to your network through a Gateway/Router,) use the Add Printer Wizard. Please follow the directions below: First, make sure that you have run the Network Setup Wizard on all of the computers on your network. We will show you 3 ways to use the Add Printer Wizard 1. Adding a local printer 2. Sharing an network printer 3. Sharing an LPR printer Adding a local printer (A printer connected directly to a computer) A printer that is not shared on the network and is connected directly to one computer is called a local printer. If you do not need to share your printer on a network, follow these directions to add the printer to one computer. • Go to Start> Printers and Faxes 66 Networking Basics Adding a local printer • Click on Add a printer • Click Next Networking Basics Adding a local printer • Select Local printer attached to this computer • (Deselect Automatically detect and install my Plug and Play printer if it has been selected.) • Click Next • Select Use the following port: • From the pull-down menu select the correct port for your printer (Most computers use the LPT1: port, as shown in the illustration.) • Click Next • Select and highlight the correct driver for your printer. • Click Next (If the correct driver is not displayed, insert the CD or floppy disk that came with your printer and click Have Disk.) 68 Networking Basics Adding a local printer • At this screen, you can change the name of the printer (optional.) • Click Next • Select Yes, to print a test page. A successful printing will confirm that you have chosen the correct driver. • Click Next This screen gives you information about your printer. • Click Finish Networking Basics Adding a local printer When the printed, test page has • Click OK • Go to Start> Printers and Faxes A successful installation will display the printer icon as shown at right. You have successfully added a local printer. 70 Networking Basics Sharing a network printer After you have run the Network Setup Wizard on all the computers on your network, you can run the Add Printer Wizard on all the computers on your network. Please follow these directions to use the Add Printer Wizard to share a printer on your network: • Go to Start> Printers and Faxes • Click on Add a Printer • Click Next Networking Basics Sharing a network printer • Select Browse for a printer • Click Next • Select the printer you would like to share. • Click Next • Click Finish 72 Networking Basics Sharing a network printer To check for proper installation: • Go to Start> Printers and Faxes The printer icon will appear at right, indicating proper installation. You have completed adding the printer. To share this printer on your network: • Remember the printer name • Run the Add Printer Wizard on all the computers on your network. • Make sure you have already run the Network Setup Wizard on all the network computers. After you run the Add Printer Wizard on all the computers in the network, you can share the printer. Networking Basics Sharing an LPR printer To share an LPR printer (using a print server,) you will need a Print Server such as the DP-101P+ or the DP-313 or a Gateway/Router with a printer port such as the DI713P. Please make sure that you have run the Network Setup Wizard on all the computers on your network. To share an LPR printer, please follow these directions: • Go to Start> Printers and Faxes • Click on Add a Printer The screen to the right will display. • Click Next • Select A Network Printer • Click Next 74 Networking Basics Sharing an LPR printer • Select Create a new port • From the pull-down menu, select Standard TCP/IP Port, as shown. • Click Next • Please read the instructions on this screen. • Click Next • Enter the Printer IP Address and the Port Name, as shown. • Click Next Networking Basics Sharing an LPR printer • In this screen, select Custom. • Click Settings • Enter the Port Name and the Printer Name or IP Address. • Select LPR • Enter a Queue Name. If there is more than one port on the print server, you must name the Queue. • Click OK 76 Networking Basics Sharing an LPR printer • This screen will show you information about your printer. • Click Finish • Select the printer you are adding from the list of Printers. • Insert the printer driver disk that came with your printer. • Click Have Disk If the printer driver is already installed, • Select Keep existing driver • Click Next Networking Basics Sharing an LPR printer • You can rename your printer if you choose. It is optional. Please remember the name of your printer. You will need this information when you use the Add Printer Wizard on the other computers on your network. • Click Next • Select Yes, to print a test page. • Click Next This screen will display information about your printer. • Click Finish to complete the addition of the printer. • Please run the Add Printer Wizard on all the computers on your network in order to share the printer. Note: You must run the Network Setup Wizard on all the computers on your network before you run the Add Printer Wizard. 78 Networking Basics Other Tasks For help with other tasks in home or small office networking, see Using the Shared Documents folder and Sharing files and folders in the Help and Support Center in Microsoft Windows XP. Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DWL-520 Wireless PCI Adapter. Read the following descriptions if you are having problems. 1. Checking the Installation of the Drivers for the Wireless Adapter • Go to Start • Right-click on My Computer • Click Properties • Select the Hardware Tab • Click Device Manager 80 Troubleshooting (continued) • Click on Network Adapters • Right-click on DWL-520 Wireless LAN Card • Select Properties to check that the drivers are installed properly. • Look under Device Status to check that the device is working properly. • Click OK DWL-520 Wireless PCI Adapter Troubleshooting (continued) 2. The computer does not recognize the DWL-520 802.11b Wireless PCI Adapter. • Make sure that the DWL-520 Wireless PCI Adapter is properly seated in the computer’s cardbus slot. • If Windows does not detect the hardware upon insertion of the adapter, make sure to completely remove drivers that were previously installed. To remove the drivers, do the following: A. Under Tools> select Folder Options…> select View > under Hidden files and folders > select Show hidden files and folders B. Uncheck Hide extension for known file types > click on Apply C. Search for the files NetA3AB.inf and A3AB.sys. Remove these files from the INF and SYSTEM32 (DRIVERS) folders in the Windows directory. Note: Windows XP and Windows 2000 will rename .inf files that have not received certification into oem.inf files (e.g., oem1.inf.) 3. The DWL-520 802.11b Wireless PCI Adapter does not work properly after the driver is installed. • Restart the computer. (In some cases, it will be necessary to restart the computer after installing the drivers.) • In Windows XP, go to Start>Control Panel>System>Hardware Tab> click on the Device Manager Tab> click on Network Adapters> double click on Wireless LAN Card(RTL8180)> make sure that “This device is working properly” is displayed under Device Status under the General Tab. (Please refer to Checking the Installation of the Drivers for the Wireless Adapter in the Networking Basics section of this manual for more information.) • If the device is not working properly and a yellow exclamation mark is displayed, then there is probably a resource conflict. In this case, make sure the computer system has a free IRQ and if necessary, uninstall the drivers, restart the system, and repeat the driver installation procedure. 82 Troubleshooting (continued) 4. The wireless client cannot access the Internet in the Infrastructure mode. • Make sure the wireless client is associated and joined with the correct Access Point. To check this connection: Right-click on the Networking Icon in the taskbar> select View Available Wireless Networks. The Connect to Wireless Network screen will appear. Please make sure you have selected the correct available network, as shown in the illustrations below. • Check that the IP Address assigned to the wireless adapter is within the same IP Address range as the access point and gateway. (For example: if one computer has an IP Address of 192.168.0.2, the other computers should have IP Addresses that are sequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must be the same for all the computers on the network.) To check the IP Address assigned to the wireless adapter, double-click on the Network Connection Icon in the taskbar > select the Support tab and the IP Address will be displayed. (Please refer to Checking the IP Address in the Networking Basics section of this manual.) If it is necessary to assign a Static IP Address to the wireless adapter, please refer to the appropriate section in Networking Basics. If you are entering a DNS Server Address, you must also enter the Default Gateway Address. (Remember that if you have a DHCP-capable router, you will not need to assign a Static IP Address. See Networking Basics: Assigning a Static IP Address.) Technical Specifications Standards • IEEE 802.11b (Wi-Fi) Supported OS • Windows XP • Windows 2000 • Windows ME • Windows 98se Frequency Range • 2400 ~ 2497MHz ISM Band Data Rates • 1, 2, 5.5, 11 Mbps Modulation Technology • Direct Sequence Spread Spectrum (DSSS) Modulation Techniques • DBPSK (Differential Binary Phase Shift Keying) • DQPSK (Differential Quadrature Phase Shift Keying) • CCK (Complementary Code Keying) Data Security • 64, 128-bit WEP (Wired Equivalent Privacy) Encryption Media Access Control • CSMA/CA with ACK Diagnostic LED • Power • Activity Current Consumption • Sleep mode - 80mA • Transmit mode - 450mA • Receive mode - 360mA 84 Operating Voltage • 5VDC ± -5% Network Architecture • Ad-Hoc Mode and 802.11 Ad-hoc Mode for network configurations that do not have any access points. • Infrastructure Mode for network configurations with access points. Antenna Type • Dipole antenna Available Channels: • 11 channels for United States/Canada • 13 channels for European Countries • 14 channels for Japan MBTF (Mean Time Between Failure) • 30,000 hours Temperature • Operating: 0ºC to 55ºC (32ºF to 131ºF) • Storing: -20ºC to 75ºC (-4ºF to 167ºF) Humidity: • 10%-90%, non-condensing Emissions: • • • FCC part 15 CE/R&TTE ARIB STD-T66 and RCR STD-33 Regulatory Statement FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCC RF Radiation Exposure Statement 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 86
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2003:06:23 09:41:45+08:00 Modify Date : 2003:06:23 09:41:45+08:00 Page Count : 86 Creation Date : 2003:06:23 01:41:45Z Mod Date : 2003:06:23 01:41:45Z Producer : Acrobat Distiller 5.0 (Windows) Metadata Date : 2003:06:23 01:41:45ZEXIF Metadata provided by EXIF.tools