D Link CS932LA1 Wireless N Day/Night Home Network Camera User Manual DCS 930L A2 UserMan 2

D Link Corporation Wireless N Day/Night Home Network Camera DCS 930L A2 UserMan 2

(DCS-930L_A2)UserMan-2

16D-Link DCS-930 User ManualSection 3 - ConfigurationInternet Connection Setup WizardThis wizard will guide you through a step-by-step process to congure your new D-Link Camera and connect the camera to the Internet. You may congure your camera using • DHCP Connection (by default), where your DHCP server will automatically assign dynamic IP to your device.• Static IP Address if your ISP has already assigned an IP address to you.• PPPoE connection, where your camera is directly connected to the Internet through a DSL modem.* Input the DNS information if you have chosen and assigned a Static IP Address for your camera.Click NextClick Next
17D-Link DCS-930 User ManualSection 3 - ConfigurationEnter a name for your camera. Congure the correct time to ensure that all events triggered, captured and scheduled at the right time. This page displays your congured settings. Click Apply to save and activate the setting, or Back to change your settings.If you have a Dynamic DNS account and would like the camera to update your IP address automatically, enable DDNS and enter your host information. Click NextClick NextClick NextClick Apply
18D-Link DCS-930 User ManualSection 3 - ConfigurationNetwork SetupSelect this connection if you have a DHCP server running on your network and would like a dynamic IP address to be updated to your camera automatically. You may obtain a static or xed IP address and other network information from your network administrator for your camera. A static IP address will ease you for accessing your camera in the future.IP Address: The xed IP addressSubnet Mask: The default value is “255.255.255.0.” Used to determine if the destination is the same subnet.Default Gateway: The gateway used to forward frames to destinations in a different subnet. Invalid gateway settings may cause the failure of transmissions to a different subnet.Primary DNS: Primary domain name server that translates names to IP addresses.Secondary DNS: Secondary domain name server to backup the Primary DNS.DHCP:Static IP Client: PPPoE Settings:Port Settings:UPnP Settings:This section allows you to congure your network settings.If you are using a PPPoE connection, enable it and enter the User Name and Password for your PPPoE account. You can get this information from your Internet service provider (ISP).You may congure a Second HTTP port that will allow you to connect to the camera via a standard web browser. The port can be set to a number other than the default TCP ports 80. A corresponding port must be opened on the router. For example, if the port is changed to 1010, users must type “http://192.168.0.100:1010” instead of only “http://192.168.0.100”. Enable this setting to congure your camera as an UPnP device in the network.
19D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > WirelessService Set Identier, an identier for your wireless network.The default setting is channel 6. Select the same channel that is using by other wireless devices within your network. When there is interference from the wireless networks that overlap with one another, you may change the channel to obtain maximum performance for your connection.Infrastructure is a wireless connection using an access point as a transmission point of all wireless devices. Ad-Hoc is a wireless connection used without an access point, where your DCS-930 is directly connecting to your PC. This is done using the on-board wireless adapter on the DCS-930 connected to a wireless adapter on the PC.This page will allow you to select a wireless network that the DCS-930 was able to detect.For security, there are three choices; None, WEP, and WPA-PSK / WPA2-PSK. Select the same encryption method that is being used by your wireless device/ router. An appropriate Preshared Key, which is needed in order to connect to the wireless network..SSID:Channel:Connection Mode:Site Survey:Wireless Security Mode:WPA-PSK / WPA2PSK Settings:Wireless InterfaceThis section allows you to setup and congure the wireless settings on your camera. DCS-930L_A2 DCS-930L_A2 DCS-930L_A2
20D-Link DCS-930 User ManualSection 3 - Configuration(Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modied. The username and password are required when using the DDNS service.Click to enable the DDNS function.Select your Dynamic DNS Server from the pull down menu.Enter the host name of the DDNS server.Enter your username or e-mail used to connect to the DDNS.Enter your password used to connect to the DDNS server.DDNS: Enable:Server Address: Host Name:User Name:Password:Setup > DDNS This section allows you to congure the DDNS setting for your camera. DDNS will allow all users to access your camera using a domain name instead of an IP address.
21D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > Image Setup Select this box to enable antiicker.Select this box to vertically rotate the video. If the camera is installed upside down, Flip Image and Mirror should both be checked.Horizontally rotates the video. Allows you to adjust the brightness level. Allows you to adjust the contrast level. Allows you to adjust the saturation level.Enable Antiicker:Flip Image: Mirror:Brightness Control:Contrast Control:Saturation Control:Image SettingsThis section allows you to congure the image settings for your camera.
22D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > VideoVideo Prole: Light Frequency:Video CongurationEncode Type:Resolution: FPS: JPEG Quality:View Mode:The compression format used when viewing your camera.Select the desired video resolution from three formats: 640x480, 320x240, and 160x120. The higher setting can obtain better quality. However, it will use more resource within your network. Select the optimal setting depending on your network status. Please note that the higher setting can obtain better quality. However, it will use more resources within your network.Choose one of ve levels of image quality: Highest, High, Medium, Low, and Lowest.Select the mode for viewing the camera image. Select Image for a still images, ActiveX for Internet Explorer, or Java for other web browsers. Select the proper frequency (50Hz or 60Hz) to reduce image icker.This section allows you to congure the video settings for your camera.This section allows you to change the Encode Type, Resolution, FPS, and Quality.
23D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > AudioEnabling audio setting will allow you to listen to audio from the camera through your PC’s audio output. Note: Please wait a few seconds for the camera to adjust the audio after the setting has been selected. Audio Settings:Volume Settings:You may Enable or Disable the camera audio feed. Select the desired volume percentage level.
24D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > Motion DetectEnabling Video Motion will allow your camera to use the motion detection feature. You may draw a nite motion area that will be used for monitoring.Motion Detection:Sensitivity: Detection Areas:Select this box to enable the motion detection feature of your camera.Species the measurable difference between two sequential images that would indicate motion. Please enter a value between 0 and 100.Use your mouse to click on the blocks that you would like to monitor for motion.
25D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > MailEmail AccountSMTP Server Address: Sender e-mail Address:Receiver e-mail Address:User Name: Password:This is the domain name or IP address of your external e-mail server. This is the e-mail address of the person sending the camera snapshots. This is the e-mail address of the recipient. If the SMTP server uses authentication, you must enter your user name here.This is the password that corresponds to your user name to connect to the SMTP server.This section allows you to congure the email notication settings for your camera.
26D-Link DCS-930 User ManualSection 3 - ConfigurationTime ScheduleEnable e-mail image to e-mail account:Interval:Test E-mail Account: Choosing Always will start sending snapshots to the recipient’s e-mail account right away. Choosing Schedule will allow you to schedule when to start and stop the sending of snapshots to the recipient’s e-mail account. The frequency of the snapshot interval can also be congured from 1 to 65535 seconds.This will send a snapshot to the e-mail account that you have congured in the E-mail section. If you have congured the SMTP account correctly, you will be able to send a test le to the e-mail account of the recipient.
27D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > FTPFTP ServerHost Address:Port Number: User Name: Password:Directory Path:Passive Mode:This is the IP address of the FTP server that you will be connecting to.Default is port 21. If changed, external FTP client program must change the server connection port accordingly.Species the user name to access the external FTP server. If you are to upload snapshots to an FTP server you will need to ll in the Domain name or IP address of your external FTP server. The following user settings must be correctly congured for remote access.Species the password to access the external FTP server.Species the destination folder in the external FTP server.Enabling passive mode will allow access to an external FTP server if your camera is behind a router protected by a rewall.This section allows you to congure a FTP server to receive images from the camera.
28D-Link DCS-930 User ManualSection 3 - ConfigurationTime ScheduleEnable upload image to FTP server:Always:Schedule: Video Frequency: Base File Name: File: Test FTP Server: Checking this box will enable video uploads to the FTP server you have selected.Selecting this option allows snapshots to be uploaded to your FTP as soon as you click Apply.Selecting this option allows you to congure specic times when you want the snapshots to be uploaded to your FTP server.Users can select in frames per second (1, 2, 3 or auto, in auto this could go to 4). The user can also select a duration for each frame from 1 to 65535 seconds.This will be the name that precedes the time, for example DCS9302010072116425101.jpg. This means that the camera took a snapshot in the year 2010, July 21 at 16th hour (4 o’clock), 42 minutes and 51 seconds and it is picture number one.If Overwrite is selected, only a few images will be constantly refreshed, depending on how many snapshots you choose to have sent. Select Date/Time Sufx and the pictures will be named with a date and time also. An example of this can be seen above under the Base le name category. Select a Sequence Number Sufx up to 1024 and all the pictures will be numbered from 1-1024. Up to 1024 pictures can be congured. Picture number 1025 will reset to number 1.This will send a snapshot to the FTP server that you have congured in the Upload section. If you have congured the FTP correctly, you will be able to see a test le on your FTP server.
29D-Link DCS-930 User ManualSection 3 - ConfigurationSetup > Time and DateTest FTP Server: Synchronize NTP Server:Copy your Computer’s Time Settings:Set the Date and Time Manually:Select the time zone for your region from the pull-down menu.Network Time Protocol will synchronize your camera with an Internet time server. Choose the one that is closest to your camera.Click to synchronize the time information from your PC. Select this to set the time manually.This section allows you to congure the settings of the internal system clocks for your camera.
30D-Link DCS-930 User ManualSection 3 - ConfigurationMaintenance > AdminThis section allows you to change the administrator’s password and congure the server settings for your camera. You can also manage the user account(s) that access to your camera.Camera Name:LED Control: User Access Control:Snapshot URL Authentication:Add User Account: User List:Specity a name for your cameraSelect Normal to enable the LED on the front of the device, or select off to disable the LED.Select Enable to enable user access control or Disable to allow only the administrator account to access the camera.Select Enable to allow access to the current camera snapshot via the web address indicated.Create new user for accessing the video image. Enter the user name, password, and password conrmation, and click Add. A maximum of 8 user accounts can be added into the user list.Displays the account names of authorized users.
31D-Link DCS-930 User ManualSection 3 - ConfigurationMaintenance > SystemThis section allows you to save and restore your conguration, restore the factory settings, and/or restart the camera.
32D-Link DCS-930 User ManualSection 3 - ConfigurationMaintenance > Firmware UpgradeYour current rmware version and date will be displayed on your screen. You may go to the D-Link Support Page to check for the latest rmware versions available. To upgrade the rmware on your DCS-930, please download and save the latest rmware version from the D-Link Support Page to your local hard drive. Locate the le on your local hard drive by using the Browse button. Then, open the le and click the “Upload” button to start the rmware upgrade. DCS-930L_A2
33D-Link DCS-930 User ManualSection 3 - ConfigurationStatus > Device InfoThis section displays all the details information about your device and network settings.
34D-Link DCS-930 User ManualSection 3 - ConfigurationStatus > Active UserThis page lists all the active user’s information including the User Name, IP address, and the time that camera access began.
35D-Link DCS-930 User ManualSection 3 - ConfigurationD-Link’s DCS-930 is a versatile and cost effective Network Camera for video monitoring. It can also serve as a powerful surveillance system in security applications. The DCS-930 can be used with any wired or 802.11n wireless router. This section explains how to view the camera from either the Internet or from inside your internal network.Materials Needed: • 1 DCS-930 Network Camera• 1 Ethernet Cable • A Wired or Wireless router such as the D-Link DI-624 Wireless Router• Ethernet based PC for system congurationSetting Up the DCS-930 For Use Behind a RouterInstalling a DCS-930 Network Camera on your network is an easy 4–step procedure:1. Assign a Local IP Address to Your Network Camera2. View the Network Camera Using Your Internet Explorer Web Browser3. Access the Router with Your Web Browser4. Open Virtual Server Ports to Enable Remote Image ViewingThis section is designed to walk you through the setup process for installing your camera behind a router and enable remote video viewing. For the basic setup of the DCS-930, follow the steps outlined in the Quick Installation Guide.Using & Conguring the DCS-930 DCS-930L_A2 DCS-930L_A2 DCS-930L_A2 DCS-930L_A2 DCS-930L_A2 DCS-930L_A2 DCS-930L_A2
36D-Link DCS-930 User ManualSection 3 - ConfigurationRun the Setup Wizard program from the CD included with the DCS-930. Follow the steps in the Quick Installation Guide to congure the DCS-930. The camera will be assigned a local IP Address that allows it to be recognized by the router. Write down this IP Address for future reference.1. Assign a Local IP Address to Your Camera After you have completed the setup of the DCS-930 outlined in the Quick Installation Guide you will have an operating camera that has an assigned IP Address. Because you are using a router to share the Internet with one or more PCs, the IP Address assigned to the Network Camera will be a local IP Address. This allows viewing within your Local Area Network (LAN) until the router is congured to allow remote viewing of the camera over the Internet.This is the IP Address assigned to your camera (192.168.0.120 is only an example). You will probably have a different IP Address.Your Camera’s IP Address DCS-930L_A2 DCS-930L_A2
37D-Link DCS-930 User ManualSection 3 - ConfigurationRun your Internet Explorer Web browser. In the address bar, type in the IP Address that was assigned to the Network Camera by the Installation Wizard program. The DCS-930 Home Page appears with a window displaying live video from the camera. You are able to view this screen from any PC running Internet Explorer on your LAN.Click on the Conguration button on the left side of the display. Scroll to the bottom of the Network Conguration page to display the ports used by HTTP and Streaming video.2. View the Network Camera Using Your Internet Explorer Web Browser DCS-930L_A2
56D-Link DCS-930 User ManualAppendix C - Technical SpecificationsTechnical SpecicationsSYSTEM REQUIREMENTS• Operating System: Microsoft Windows XP, Vista, Windows 7• Internet Explorer 6 or above , Firefox 3.5 or above, Safari 4NETWORKING PROTOCOL• IPV4, ARP, TCP, UDP, ICMP• DHCP Client• NTP Client (D-Link)• DNS Client• DDNS Client (Dyndns and D-Link)• SMTP Client• FTP Client• HTTP Server• PPPoE• UPnP Port Forwarding• LLTD• UPnP-X1BUILT-IN NETWORK INTERFACE• 10/100BASE-TX Fast Ethernet• 802.11b/g/n WLANWIRELESS CONNECTIVITY• 802.11b/g/n Wireless with WEP/WPA/WPA2 securityWIRELESS TRANSMIT OUTPUT POWER• 16 dbm for 11b, 12 dbm for 11g, 12 dbm for 11n (typical)SDRAM• 32 MBFLASH MEMORY• 4 MBRESET BUTTON• Reset to factory defaultVIDEO CODECS• MJPEG• JPEG for still imagesVIDEO FEATURES• Adjustable image size and quality• Time stamp and text overlay• Flip and MirrorRESOLUTION• 640 x 480 at up to 20 fps• 320 x 240 at up to 30 fps• 160 x 120 at up to 30 fps
57D-Link DCS-930 User ManualAppendix C - Technical SpecificationsLENS• Focal length: 5.01 mm, F2.8SENSOR• VGA 1/5 inch CMOS SensorMINIMUM ILLUMINATION• 1 lux @ F2.8VIEW ANGLE• Horizontal: 45.3°• Vertical: 34.5°• Diagonal: 54.9°DIGITAL ZOOM• Up to 4x3A CONTROL• AGC (Auto Gain Control)• AWB (Auto White Balance)• AES (Auto Electronic Shutter)POWER• Input: 100-240 V AC, 50/60 Hz• Output: 5 V DC, 1.2 A• External AC-to-DC switching power adapterDIMENSIONS (W X D X H)• Including the bracket and stand: 65.8 x 65 x 126 mm• Camera only: 27.2 x 60 x 96 mmWEIGHT• 76.9 g (without bracket and stand)MAX POWER CONSUMPTION• 2 WOPERATION TEMPERATURE• 0 ˚C to 40 ˚C (32 ˚F to 104 ˚F)STORAGE TEMPERATURE• -20 ˚C to 70 ˚C (-4 ˚F to 158 ˚F)HUMIDITY• 20-80% RH non-condensingEMISSION (EMI), SAFETY & OTHER CERTIFICATIONS• FCC Class B• IC• C-Tick• CE
FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance."
Canada Notices Industry Canada regulatory information Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements. Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions.

Navigation menu