D Link DIR456A1 Residential USIM Embedded HSDPA 3G Router User Manual Manual v1 00 FCC NCC

D Link Corporation Residential USIM Embedded HSDPA 3G Router Manual v1 00 FCC NCC

UserManual.wiki >

D Link >

DIR456A1 User Manual HTML Version

User Manual

ftjefoujbm!VTJN!Fncfeefe!ITEQB!4H!Spvufs!

!!!!!!!փ৬4Hጻ׬୮شሁطᕴ!

iD-Link DIR-456 User Manual

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to

notify any person or organization of such revisions or changes.

Trademarks

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in

the United States or other countries. All other company or product names mentioned herein are trademarks or

registered trademarks of their respective companies.

permission from D-Link Systems, Inc.

Preface

iiD-Link DIR-456 User Manual

Table of Contents

Preface...........................................................................i

Trademarks .............................................................. i

Product Overview ........................................................ 1

Package Contents ...................................................1

System Requirements ............................................. 1

Introduction ..............................................................2

Hardware Overview ................................................. 3

Rear Panel .........................................................3

Front Panel ........................................................4

LEDs .................................................................. 5

Installation ....................................................................6

Connect to Your Network ........................................6

Connect a Telephone ..............................................7

Wireless Installation Considerations ........................ 8

Conﬁguration ............................................................... 9

Web-based Conﬁguration Utility .............................. 9

Setup Wizard ......................................................... 10

Internet Connection Setup Wizard ................... 10

Manual Internet Connection Setup ..................14

Internet Connection ......................................... 15

Internet Connection Type ................................ 15

Static IP ...........................................................16

Dynamic IP (DHCP) ......................................... 17

PPPoE ............................................................. 18

PPTP ............................................................... 19

L2TP ................................................................ 20

Russia PPTP (Dual Access) ............................ 21

Russia PPPoE (Dual Access) .......................... 23

3G Internet ....................................................... 25

Wireless Settings ............................................. 26

Network Settings ..............................................28

Router Settings ............................................28

DHCP Server Settings .................................29

DHCP Reservations .....................................30

Message Service .............................................31

Virtual Server ................................................... 33

Application Rules ............................................. 34

QoS Engine ..................................................... 35

Network Filter ................................................... 36

Website Filter ................................................... 37

Firewall Settings ..............................................38

Advanced Wireless .......................................... 40

Wi-Fi Protected Setup ...................................... 42

Advanced Network ...........................................44

Call Setting ...................................................... 46

Admin ............................................................... 47

Time ................................................................. 48

Email Settings .................................................. 49

System ............................................................. 50

Firmware .......................................................... 51

Table of Contents

iiiD-Link DIR-456 User Manual

Table of Contents

Dynamic DNS ..................................................52

System Check ..................................................53

Schedules ........................................................ 54

Device Information ........................................... 55

Logs ................................................................. 56

Statistics .......................................................... 57

Internet Sessions ............................................. 58

Wireless ........................................................... 59

Support ............................................................ 60

Wireless Security....................................................... 61

What is WEP? .......................................................61

Conﬁgure WEP ...................................................... 62

What is WPA? .......................................................63

Conﬁgure WPA-PSK .............................................64

Conﬁgure WPA (RADIUS) ..................................... 65

Using Windows® 7 and WPS for Wireless

Conﬁguration ......................................................... 66

Connecting to a Wireless Network

Using Windows® 7 ................................................. 70

Connecting to a Wireless Network

Using Windows Vista® .......................................... 73

Connecting to a Wireless Network ........................75

Using Windows® XP ............................................... 75

Troubleshooting ........................................................ 77

Wireless Basics ......................................................... 79

What is Wireless? .................................................. 80

Tips ........................................................................ 82

Wireless Modes ..................................................... 83

Networking Basics .................................................... 84

Check your IP address ..........................................84

Statically Assign an IP address ............................. 85

Technical Speciﬁcations........................................... 86

1D-Link DIR-456 User Manual

Section 1 - Product Overview

• D-Link DIR-456 Mobile Router

• Power Adapter

• Ethernet Cable

• RJ-11 Telephone Cable

• Manual and Warranty on CD

System Requirements

• A compatible (U)SIM card with service*

• Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet

adapter

• Internet Explorer Version 6.0 or Netscape Navigator™ Version 6.0 and above (for conﬁguration)

*Subject to services and service terms available from your carrier.

Product Overview

Package Contents

Note: Using a power supply with a different voltage rating than the one included with the DIR-456 will cause damage and void

the warranty for this product.

2D-Link DIR-456 User Manual

Section 1 - Product Overview

Introduction

DIR-456 allows users to access worldwide mobile broadband networks. Once connected, users can transfer data,

stream media, send SMS messages, and make mobile phone calls. Simply insert your UMTS/HSDPA SIM card,

and share your 3.5G Internet connection through a secure 802.11n wireless network or using any of the four 10/100

Ethernet ports.

While accessing your 3.5G Internet connection, you will still have the ability to answer incoming mobile calls and

respond to SMS messages. An RJ-11 jack allows you to attach a standard analog phone for high-quality mobile

calls over a GSM network. Enjoy the comfort and convenience of your favorite ofﬁce phone anywhere you go.

Keep your wireless network safe with WPA/WPA2 wireless encryption. The DIR-456 utilizes dual-active ﬁrewalls

(SPI and NAT) to prevent potential attacks across the Internet.

DIR-456 can be installed quickly and easily almost anywhere. This router is great for situations where an impromptu

wireless network must be set up, or wherever conventional network access is unavailable. The DIR-456 can even

be installed in buses, trains, or boats, allowing passengers to check e-mail or chat online while commuting.

3D-Link DIR-456 User Manual

Section 1 - Product Overview

Hardware Overview

Rear Panel

WPS USIM FXS LAN2 LAN1 WAN Power RESET

Port Function

LAN 1-2 (RJ-45) Insert an Ethernet cable connected to a network device such

as a desktop or notebook computer.

WAN (RJ-45) Insert a standard CAT5 Ethernet cable connected to a DSL/

Cable modem or router.

SIM Insert a standard (U)SIM card into this slot.

Power Insert the provided DC power adapter into this socket.

Phone (RJ-11) Insert an RJ-11 telephone cable connected to a standard

landline telephone.

Reset Hold this button down to reset the device.

WPS Press this button to initiate a new WPS connection.

Power

Connector

4D-Link DIR-456 User Manual

Section 1 - Product Overview

Hardware Overview

Front Panel

Power 3G WLAN SMS

WAN Signal

Strength

Phone WPS

5D-Link DIR-456 User Manual

Section 1 - Product Overview

LED Name Function

WAN Solid Green: Ethernet connection has been established

Blinking Green: Data is being transferred

LAN 1-2 Solid Green: Ethernet connection has been established

Blinking Green: Data is being transferred

Signal

Strength

OFF: No signal

ON (Blinking Orange): Signal is weak

ON (Solid Orange): Signal strength is medium

ON (Solid Green): Signal strength is strong

WPS Slow Blinking Green: WPS is functioning normally

Fast Blinking Green: WPS is functioning in PBC mode

3.5G Solid Green: UMTS/HSDPA/HSUPA connection has been established

Solid Orange: GPRS/EDGE connection has been established

Blinking: Data is being transferred via 3G

SMS Solid Green: Lights up when an SMS has been received

WLAN Solid Green: WLAN is active and available

Blinking Green: Data is being transferred via WLAN

Hardware Overview

LEDs

6D-Link DIR-456 User Manual

Section 2 - Installation

Connect to Your Network

Installation

This section will guide you through the installation process. Placement of the router is very important. Do not place the router in an enclosed

area such as a closet, cabinet, or in an attic or garage.

Note: Ensure that your DIR-456 Mobile Router is disconnected and powered off before performing the installation steps below.

1. Insert a standard (U)SIM card into the SIM card slot on the back of the router with the gold contacts facing downwards.

2. Insert your Internet/WAN network cable into the INTERNET port on the back of the router.

Note: The 3.5G connection can also be used as a backup WAN. Once a backup is conﬁgured, the router will automatically use 3.5G

for the Internet connection if the Ethernet WAN is not available.

3. Insert the Ethernet cable into the LAN Port 1 on the back panel of the DIR-456 Mobile Router, and an available Ethernet port on the

network adapter in the computer you will use to conﬁgure the unit.

Note: The DIR-456 Mobile Router LAN Ports are “Auto-MDI/MDIX.” Therefore, patch or crossover Ethernet cables can be used.

4. Connect the power adapter to the socket on the back panel of your DIR-456 Mobile Router. Plug the other end of the power adapter

into a wall outlet or power strip.

a. The Status LED will light up to indicate that power has been supplied to the router.

b. The LEDs on the front panel will ﬂash on and off as the DIR-456 Mobile Router performs initialization and Internet connection

processes.

c. After a few moments, if a connection has been established, the following LEDs will turn solid green: Power, Status, WAN, WLAN,

and LAN Port 1 (or whichever port(s) your Ethernet cable has been connected to).

Caution! Always unplug/power down the router before installing or removing the SIM card. Never insert or remove the SIM card while

the router is in use.

7D-Link DIR-456 User Manual

Section 2 - Installation

Connect a Telephone

A standard RJ-11 jack on the back of the router allows you to connect a standard analog telephone for voice calls.

Simply plug the phone cable into the jack labeled FXS.

You can then use your handset to dial out as you typically would with a standard landline.

Your attached phone will also ring for any incoming voice calls.

8D-Link DIR-456 User Manual

Section 2 - Installation

Wireless Installation Considerations

The DIR-456 can be accessed using a wireless connection from virtually anywhere within the operating range of your wireless network.

Keep in mind, however, that the quantity, thickness and location of walls, ceilings, or other objects that the wireless signals must pass

through, may limit the range. Ranges vary depending on the types of materials and background RF (radio frequency) noise in your home

or ofﬁce. The key to maximizing the wireless range is to follow these basic guidelines:

1. Minimize the number of walls and ceilings between the D-Link router and other network devices. Each wall or ceiling can

reduce your adapter’s range from 3 to 90 feet (1 to 30 meters).

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters), at a 45-degree angle

appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick. Position devices

so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.

3. Try to position access points, wireless routers, and computers so that the signal passes through open doorways and

drywall. Materials such as glass, metal, brick, insulation, concrete and water can affect wireless performance. Large

objects such as ﬁsh tanks, mirrors, ﬁle cabinets, metal doors and aluminum studs may also have a negative effect on

range.

4. If you are using 2.4GHz cordless phones, make sure that the 2.4GHz phone base is as far away from your wireless device

as possible. The base transmits a signal even if the phone in not in use. In some cases, cordless phones, X-10 wireless

devices, and electronic equipment such as ceiling fans, ﬂuorescent lights, and home security systems may dramatically

degrade wireless connectivity.

9D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Conﬁguration

This section will show you how to conﬁgure your new D-Link mobile router using the web-based conﬁguration utility.

Web-based Conﬁguration Utility

To access the conﬁguration utility, open a web-browser such

as Internet Explorer and enter the IP address of the router

(192.168.0.1).

Type Admin and then enter the password. By default, the

password is blank.

If you get a Page Cannot be Displayed error, please refer to

the Troubleshooting section for assistance.

10D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Setup Wizard

The setup wizard guides you through the initial setup of your router.

There are two ways to setup your Internet connection. You can use the

Web-based Internet Connection Setup Wizard or you can manually

conﬁgure using the Manual Internet Connection Setup wizard.

Click Internet Connection Setup Wizard to begin.

If you want to enter your settings without running the wizard, click

Manual Internet Connection Setup and skip to page 14.

This wizard will guide you through a step-by-step process to conﬁgure

your D-Link router to connect to the Internet.

Click Next to continue.

Internet Connection Setup Wizard

11D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Create a new password and then click Next to continue.

Click Prev to go back to the previous page or click Cancel to close the wizard.

Select your time zone from the drop-down box and then click Next to continue.

Click Prev to go back to the previous page or click Cancel to close the wizard.

Select the Internet connection type. The connection types are explained on the

following page. If you are unsure of the correct connection type, you may have to

contact your Internet Service Provider (ISP).

Click Prev to go back to the previous page or click Cancel to close the wizard.

Note: The DIR-456 supports several kinds of WAN interfaces, allowing you to assign

either a WAN or a WWAN(3.5G) connection as the Backup WAN. If the Primary

WAN is down or unavailable, conﬁgure the Backup WAN to Enable, and all the

trafﬁc will be routed through Backup WAN. This feature is called WAN Failover.

You can use WAN Failover if you need redundancy to your Internet connection or

any other network.

12D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Choose this option if your Internet connection uses an IP address that does not change. Your ISP generally

will provide you with this information. See page 16 for information about how to conﬁgure this type of

connection.

Choose this if your Internet connection automatically provides you with an IP Address. Most cable modems

use this type of connection. See page 17 for information about how to conﬁgure this type of connection.

Choose this option if your Internet connection requires a username and password to connect. Most DSL modems

use this style of connection. See page 18 for information about how to conﬁgure this type of connection.

Choose this option if your Internet connection requires Point-to-Point Tunneling Protocol (PPTP). See page

19 for information about how to conﬁgure this type of connection.

Choose this option if your Internet connection requires Layer 2 Tunneling Protocol (L2TP). See page 21 for

information about how to conﬁgure this type of connection.

To conﬁgure a Russian PPTP Internet connection, conﬁgure as previously described for PPTP connections.

See page 21 for information about how to conﬁgure this type of connection.

Some PPPoE connections use a static IP route to the ISP in addition to the global IP settings for the connection.

This requires an added step to deﬁne IP settings for the physical WAN port. To conﬁgure a Russian PPPoE

Internet connection, conﬁgure as previously described for PPPoE connections and add the physical WAN

IP settings as instructed by your ISP. See page 23 for information about how to conﬁgure this type of

connection.

Select this option if you do not need to conﬁgure 3G.

Static IP Address

Connection:

DHCP Connection

(Dynamic IP Address):

Username / Password

Connection (PPPoE):

Username / Password

Connection (PPTP):

Username / Password

Connection (L2TP):

Russia PPTP (Dual

Access):

Russia PPPoE (Dual

Access):

Skip 3G Conﬁguration:

The subsequent conﬁguration pages will differ depending on the selection you make on this page.

13D-Link DIR-456 User Manual

Section 3 - Conﬁguration

You have completed the Setup Wizard.

Click Connect to save your settings.

A popup will appear to conﬁrm your settings.

Click OK to save your settings.

14D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Manual Internet Connection Setup

Click Manual Internet Connection Setup to begin.

If you prefer to conﬁgure your router’s Internet connection using the wizard,

click Internet Connection Setup Wizard and refer to page 10.

15D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Several different Internet Connection types can be selected depending upon the speciﬁcations of your Internet Service Provider (ISP).

Select the Internet Connection type

speciﬁed by your Internet Service

Provider (ISP). The corresponding

settings will be displayed below.

Please see the following pages for

details on how to conﬁgure these

different connection types.

When this box is checked, the

selected connection will act as a

backup for the 3.5G connection.

Select this box to enable checking

wired-WAN alive. The router will test

your connection status and connect

to the 3G connection if your WAN

connection goes down.

Enter the IP address of the Internet host to be used as the backup connection.

Internet Connection

Internet Connection Type

My Internet Connection is:

Enable WAN Failover:

Internet Host:

16D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Enter the IP address assigned to

your network connection.

Enter the subnet mask.

Enter the default gateway.

Enter the primary DNS server.

Enter the secondary DNS server.

You may need to change the

Maximum Transmission Unit (MTU)

for optimal performance. The default value is 1500.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router.

It is not recommended that you change the default MAC address unless required by your ISP. You can use

the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address

of your Ethernet card.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

IP Address:

Subnet Mask:

Default Gateway:

Primary DNS Server:

Secondary DNS Server:

MTU:

MAC Address:

Choose this Internet connection if your ISP assigns you a static IP address.

Static IP

17D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Dynamic IP (DHCP)

(Optional) Required by some ISPs.

(Optional) Fill in with IP address of primary DNS

server.

(Optional) Fill in with IP address of secondary DNS

server.

You may need to change the Maximum Transmission

Unit (MTU) for optimal performance. The default

value is 1500.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router.

It is not recommended that you change the default MAC address unless required by your ISP. You can use

the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address

of your PC.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

This section will help you to obtain IP Address information automatically from your ISP. Use this option if your ISP didn’t provide you with

IP Address information and/or a username and password.

Host Name:

Primary DNS Server:

Secondary DNS Server:

MTU (Maximum

Transmission Unit):

MAC Address:

18D-Link DIR-456 User Manual

Section 3 - Conﬁguration

PPPoE

Choose this Internet connection if your ISP provides you PPPoE account.

The username/account name that your ISP provides

to you for PPPoE dial-up.

The password that your ISP provides to you for

PPPoE dial-up.

Re-enter the password.

(Optional) Fill in if provided by your ISP. If not, keep

the default value.

(Optional) Fill in if provided by your ISP. If not, keep

the default value.

(Optional) Fill in if provided by your ISP. If not, keep the default value.

MAC address of WAN interface. You can also copy MAC address of your PC to its WAN interface by pressing

Clone Your PC’s MAC button. The Restore MAC button will reset the router to its default MAC address.

The amount of time of inactivity before disconnecting established PPPoE session. Set it to zero or enable

Auto-reconnect will disable this feature.

The default setting of PPPoE is 1492.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Username:

Password:

Verify Password:

IP Address:

Primary DNS Server:

Secondary DNS Server:

MAC Address:

Maximum Idle Time:

Maximum Transmission

Unit (MTU):

19D-Link DIR-456 User Manual

Section 3 - Conﬁguration

PPTP

Choose this Internet connection if your ISP provides you PPTP account.

Choose Static IP only if your ISP assigns you an IP

address. Otherwise, please choose Dynamic IP.

Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.)

Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.)

Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.)

Enter the IP address of the PPTP server.

User/account name that your ISP provides to you for PPTP dial-up.

Password that your ISP provides to you for PPTP dial-up.

Re-enter the password.

Choose Always-on when you want to establish PPTP connection all the time. If you choose Connect-on-

demand, the device will establish PPTP connection when local users want to surf Internet, and disconnect if

no trafﬁc after time period of Maximum Idle Time.

The time of no activity to disconnect your PPTP session. Set it to zero or choose Always-on to disable this

feature.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Address Mode:

PPTP IP Address:

PPTP Subnet Mask:

PPTP Gateway IP Address:

PPTP Server IP Address:

Username:

Password:

Verify Password:

Reconnect Mode:

Maximum Idle Time:

20D-Link DIR-456 User Manual

Section 3 - Conﬁguration

L2TP

Choose this Internet connection if your ISP provides you L2TP account.

Choose Static IP only if your ISP assigns you an IP

address. Otherwise, please choose Dynamic IP.

Enter the information provided by your ISP.

(Only applicable for Static IP L2TP.)

Enter the information provided by your ISP.

(Only applicable for Static IP L2TP.)

Enter the information provided by your ISP.

(Only applicable for Static IP L2TP.)

IP address of L2TP server.

User/account name that your ISP provides to you for L2TP dial-up.

Password that your ISP provides to you for L2TP dial-up.

Re-enter the password.

Choose Always-on when you want to establish L2TP connection all the time. Choose Connect-on-demand the

device will establish L2TP connection when local users want to surf Internet, and disconnect if no trafﬁc after

time period of Maximum Idle Time.

The time of no activity to disconnect your L2TP session. Set it to zero or choose Always-on to disable this

feature.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Address Mode:

L2TP IP Address:

L2TP Subnet Mask:

L2TP Gateway IP Address:

L2TP Server IP Address:

Username:

Password:

Verify Password:

Reconnect Mode:

Maximum Idle Time:

21D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Russia PPTP (Dual Access)

Choose this Internet connection if you are using PPTP in Russia.

Choose Static IP only if your ISP assigns you an IP

address. Otherwise, please choose Dynamic IP.

Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.)

Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.)

Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.)

Enter the IP address of the PPTP server.

User/account name that your ISP provides to you

for PPTP dial-up.

Password that your ISP provides to you for PPTP dial-up.

Re-enter the password.

Choose Always-on when you want to establish PPTP connection all the time. If you choose Connect-on-

demand, the device will establish PPTP connection when local users want to surf Internet, and disconnect if

no trafﬁc after time period of Maximum Idle Time.

The time of no activity to disconnect your PPTP session. Set it to zero or choose Always-on to disable this

feature.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Address Mode:

PPTP IP Address:

PPTP Subnet Mask:

PPTP Gateway IP Address:

PPTP Server IP Address:

Username:

Password:

Verify Password:

Reconnect Mode:

Maximum Idle Time:

22D-Link DIR-456 User Manual

Section 3 - Conﬁguration

(Optional) Fill in with IP address of primary DNS server.

(Optional) Fill in with IP address of secondary DNS server.

You may need to change the Maximum Transmission Unit (MTU) for optimal performance. The default value

is 1400.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router.

It is not recommended that you change the default MAC address unless required by your ISP. You can use

the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address

of your PC.

Primary DNS Server:

Secondary DNS Server:

Maximum Transmission

Unit (MTU):

MAC Address:

23D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Russia PPPoE (Dual Access)

Choose this Internet connection if you are using PPPoE in Russia.

Choose Static IP only if your ISP assigns you an IP

address. Otherwise, please choose Dynamic IP.

(Optional) Fill in if provided by your ISP. If not, keep

the default value.

The username/account name that your ISP provides

to you for PPPoE dial-up.

Password that your ISP provides to you for PPPoE

dial-up.

(Optional) Enter the service name.

Always - The connection will always be on.

Schedule - The connection run according to a

speciﬁed schedule.

On demand - The router will reconnect when

needed.

Manual - The router will reconnect only

when the user initiates a connection.

The amount of time of inactivity before disconnecting

established PPPoE session. Setting it to zero or

enabling Auto-reconnect will disable this feature.

You may choose Receive DNS from ISP or Enter DNS Manually.

(Optional) Fill in with IP address of primary DNS server.

(Optional) Fill in with IP address of secondary DNS server.

Address Mode:

IP Address:

Username:

Password:

Verify Password:

Service Name:

Reconnect Mode:

Maximum Idle Time:

DNS Mode:

Primary DNS Server:

Secondary DNS Server:

24D-Link DIR-456 User Manual

Section 3 - Conﬁguration

You may need to change the Maximum Transmission

Unit (MTU) for optimal performance. The default

value is 1492.

The default MAC Address is set to the Internet port’s

physical interface MAC address on the Broadband

Router. It is not recommended that you change the

default MAC address unless required by your ISP.

You can use the Clone Your PC’s MAC Address

button to replace the Internet port’s MAC address

with the MAC address of your PC.

WAN PHYSICAL SETTINGS

Choose Static IP only if your ISP assigns you an IP

address. Otherwise, please choose Dynamic IP.

(Optional) Fill in if provided by your ISP. If not, keep

the default value.

Enter the Subnet Mask of the router. The default

subnet mask is 255.255.255.0.

Enter the default gateway.

(Optional) Fill in with IP address of primary DNS

server.

(Optional) Fill in with IP address of secondary DNS server.

Maximum Transmission

Unit (MTU):

MAC Address:

Address Mode:

IP Address:

Subnet Mask:

Gateway:

Primary DNS Address:

Secondary DNS Address:

25D-Link DIR-456 User Manual

Section 3 - Conﬁguration

You may select GPRS/EDGE or WCDMA as the

preferred service type.

Select this box to enable automatic conﬁguration.

Select your country.

Select your ISP.

(Optional) Fill in only if requested by your ISP.

Enter the number to be dialed.

(Optional) Enter the APN information.

You may select from the following option:

Always-on - The 3G connection will always be on.

Connect on demand - The router will reconnect when needed.

Manual - The router will reconnect only when the user initiates a connection.

The default value for 3G is 1492.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Prefer Service Type:

Auto Conﬁg:

Country:

ISP:

User Name:

Password:

Dial Number:

APN:

Reconnect Mode:

MTU (Maximum

Transmission Unit:

3G Internet

Choose this Internet connection if you already apply a SIM card for 3G Internet service from Telecom company. The ﬁelds here may not

be necessary for your connection. The information on this page is only be used when your service provider requires.

26D-Link DIR-456 User Manual

Section 3 - Conﬁguration

WIRELESS NETWORK SETTINGS

Select this checkbox to enable wireless

access. When you set this option, the

following parameters take effect.

Also known as the SSID (Service

Set Identifier), this is the name of

your Wireless Local Area Network

(WLAN). Enter a name using up to 32

alphanumeric characters. The SSID is

case-sensitive.

A wireless network uses speciﬁc channels

in the wireless spectrum to handle

communication between clients. Some

channels in your area may experience

interference from other electronic

devices. Choose the clearest channel

to help optimize the performance and

coverage of your wireless network.

Click Save Settings to save your

changes, or click Don’t Save Settings

to discard your changes.

Enable Wireless:

Wireless Network Name:

Auto Channel Scan:

Wireless Settings

This section will help you to manually conﬁgure the wireless settings of your router. Please note that changes made on this section may

also need to be duplicated on your Wireless Client.

27D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Indicates the channel setting for the DIR-456.

By default the channel is set to 11. This can

be changed to ﬁt the channel setting for an

existing wireless network or to customize

your wireless network. Click Auto Channel

Scan to automatically select the channel that

it will operate on. This option is recommended

because the router will choose the channel with

the least amount of interference.

Select Invisible if you do not want the SSID

of your wireless network to be broadcasted by

DIR-456. The SSID of your router will not be

seen by Site Survey utilities. Therefore while

setting up your wireless clients, you will have

to manually enter your SSID to connect to the

router.

WIRELESS SECURITY MODE

This device supports three wireless security

modes, WEP, WPA-Personal, WPA-

Enterprise or None. WEP is the original

wireless encryption standard. WPA provides a higher level of security and WPA-Personal does not require an

authentication server. When WPA enterprise is enabled, the router uses EAP (802.1x) to authenticate clients

via a remote RADIUS server.

IP address of RADIUS server.

The port used for RADIUS server. The default port is 1812.

Key value shared by RADIUS server and this device.

Please refer to Section 4 - Wireless Security for more information on security and encryption.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Wireless Channel:

Visibility Status:

Security Mode:

Radius Server IP:

Radius Port:

Radius Shared Key:

28D-Link DIR-456 User Manual

Section 3 - Conﬁguration

This section will help you to change the internal network settings of your router and to conﬁgure the DHCP Server settings.

Network Settings

Router Settings

Enter the IP address of the router. The

default IP address is 192.168.0.1.

If you change the IP address, you will need

to enter the new IP address in your browser

to get into the conﬁguration utility.

Enter the Subnet Mask of the router. The

default subnet mask is 255.255.255.0.

Enter the local domain name for your

network.

Click Save Settings to save your changes,

or click Don’t Save Settings to discard

your changes.

Router IP Address:

Default Subnet Mask:

Local Domain Name:

29D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Select this box to enable the DHCP

server on your router.

Enter the starting and ending

IP address for the server’s IP

assignment.

The time period for the IP address

lease. Enter the Lease time in

minutes.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Enable DHCP Server:

DHCP IP Address Range:

DHCP Lease Time:

DHCP Server Settings

The DIR-456 has a built-in DHCP (Dynamic Host Control Protocol) server. The DHCP server assigns IP addresses to devices on the network

that request them. By default, the DHCP Server is enabled on the device. The DHCP address pool contains a range of IP addresses,

which is automatically assigned to the clients on the network.

30D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Select the box next to the computer name to

enable the DHCP reservation.

Speciﬁes the name of the workstation.

Speciﬁes IP Address of the workstation.

Speciﬁes the MAC Address of workstation.

Click Save Settings to save your changes, or click

Don’t Save Settings to discard your changes.

DHCP Reservations

Enable:

Computer Name:

IP Address:

MAC Address:

31D-Link DIR-456 User Manual

Section 3 - Conﬁguration

SMS INBOX

Click this button to view any SMS

message that you may have

received.

CREATE MESSAGE

Click this button to create a

message.

Message Service

SMS Inbox:

Create Message:

If your ISP provide SMS service, you can create new messages, and manage your messages from this page.

32D-Link DIR-456 User Manual

Section 3 - Conﬁguration

CREATE MESSAGE

This page allows you to send an SMS to your

contacts. Just fill in the phone number of the

recipient, and type the content of message. Then

push the “Send Message” button to send out this

message. If you would like to add more than one

recipient, you must put a semicolon (;) between

each of the phone numbers.

Type the phone number of the recipient.

Type the message that you would like to send.

Click this button to send the message.

Click this button to cancel message input.

INBOX

This page shows all messages that are stored on

the SIM card. Selecting a message, and the content

will be shown in the SMS window. After you read it,

you can delete it, or reply to the sender. Push the

“Refresh” button to update the list.

SMS

Deletes the selected SMS message.

Replies to the selected SMS message.

Click this button to check for new messages.

Receiver:

Text Message:

Sent Message:

Cancel:

Delete Message:

Reply Message:

Refresh:

33D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Virtual Server

The device can be conﬁgured as a virtual server so that users can access services such as Web or FTP via the public (WAN) IP address

of the router.

You may select Always On or

choose the number of a schedule

rule that you have deﬁned.

VIRTUAL SERVERS LIST

Identiﬁes the virtual server.

Enter the last digits of the IP

address of the computer on your

local network that you want to allow

the incoming service. In the next

box, enter the port number that you

would like to open.

Select this box to enable the rule.

Specify the schedule rule

number.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Use schedule rule:

ID:

Server IP: Port:

Enable:

Schedule Rule #:

34D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Application Rules

Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These

applications have difﬁculties working through NAT (Network Address Translation). Applications Rules allow some of these applications

work with the DIR-456.

APPLICATION RULES

Select this box to enable the rule.

Enter a name for the rule.

Select from a list of popular applications.

The name of the trigger.

The port that will be used on your internal

network.

The port that will be accessed from the

Internet.

Select TCP or UDP.

Specify whether the rule should always be

active, or active according a predefined

schedule.

Click Save Settings to save your changes,

or click Don’t Save Settings to discard your

changes.

Enable:

Name:

Applications:

Trigger:

Firewall:

Protocol:

Schedule:

35D-Link DIR-456 User Manual

Section 3 - Conﬁguration

QoS Engine

QoS ENGINE SETUP

Check this option if you want to

enable the QoS function.

Check this option to automatically

get the optimal performance.

This field displays the current

measured uplink speed here.

If the measured uplink speed is

not optimal, please disable the

Automatic Uplink Speed and

select the transmission rate from

drop-down menu.

You can choose auto-detect for the known connection type. Or choose xDSL or cable etc if you know what

connection type you use for the Internet network.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Enable QoS Engine:

Automatic Uplink Speed:

Measured Uplink Speed:

Manual Uplink Speed:

Connection Type:

The QoS Engine improves your online gaming experience by ensuring that your game trafﬁc is prioritized over other network trafﬁc, such

as FTP or Web. For best performance, use the Automatic Classiﬁcation option to automatically set the priority for the applications.

36D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Network Filter

MAC FILTERING SETTINGS

Select this box to enable MAC Filtering.

The MAC address of the network device to

be added to the MAC Filter List.

DHCP clients will have their hostname in

the Computer Name drop down menu. You

can select the client computer you want to

add to the MAC Filter List and click arrow

button. This will automatically add that

computer’s MAC address to the appropriate

ﬁeld.

Click Save Settings to save your changes,

or click Don’t Save Settings to discard

your changes.

Enable:

MAC Address:

DHCP Client List:

The MAC (Media Access Controller) Address Filter option is used to control network access based on the MAC Address of the network

adapter. A MAC address is a unique ID assigned by the manufacturer of the network adapter. This feature can be conﬁgured to ALLOW

or DENY network/Internet access.

37D-Link DIR-456 User Manual

Section 3 - Conﬁguration

WEBSITE FILTERING RULES

Specify the way website ﬁltering should operate.

You may specify from the following:

- Turn OFF WEBSITE FILTERING

- ALLOW access to ONLY these sites

- DENY access to ONLY these sites

Enter the URLs that you would like to filter.

Select the checkbox next to the URL to enable

the URL.

Choose whether the ﬁlter should always be on, or

specify a schedule to use. Select New Schedule

to create a new schedule.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

URL Filter allows you to set up a list of Web-sites that will be blocked from users on your network.

Website Filter

Conﬁgure Website Filter

Below:

Website URL:

Schedule:

38D-Link DIR-456 User Manual

Section 3 - Conﬁguration

FIREWALL SETTINGS

Select this box to enable Stateful Packet

Inspection (SPI).

DMZ HOST

Select this box to enable to the DMZ.

Select a computer from the dropdown box and

click the << button to display the IP address.

Firewall Settings

Firewall rules can be used to allow or deny trafﬁc passing through the router. You can specify a single port by utilizing the input box at the

top or a range of ports by utilizing both input boxes. DMZ means “Demilitarized Zone.” DMZ allows computer behind the router ﬁrewall to

be accessible to Internet trafﬁc. Typically, your DMZ would contain Web servers, FTP servers and others.

Enable SPI:

Enable DMZ:

DMZ IP Address:

39D-Link DIR-456 User Manual

Section 3 - Conﬁguration

FIREWALL RULES

Enter a name for the rule.

Specify the interface for the source and destination.

You may select LAN, WAN, or WAN(3G).

Enter the starting and ending IP address that you

wish to apply the rule to. If you are only applying this rule to one IP address, you may enter the same IP address

in both boxes.

Specify a protocol for the rule. You may select TCP, UDP, ICMP.

Specify whether to Allow or Deny access.

Specify the starting port and ending port.

Specify when the rule should be active. You may choose: Always or specify a schedule. Click New Schedule

to open the Schedules page.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Name:

Interface:

IP Address:

Protocol:

Action:

Port Range:

Schedule:

40D-Link DIR-456 User Manual

Section 3 - Conﬁguration

You can lower the output power of the router

by selecting lower percentage Transmit Power

values from the drop down. Your choices are:

100%, 50%, 25%, and 12.5%.

Beacons are packets sent by an Access Point

to synchronize a wireless network. Specify a

Beacon interval value between 20 and 1000.

The default value is set to 100 milliseconds.

This value should remain at its default setting of

2346. If you encounter inconsistent data ﬂow,

only minor modiﬁcations to the value range

between 256 and 2346 are recommended.

The default value for RTS Threshold is set to

2346.

This value should remain at its default setting of 2346. If you experience a high packet error rate, you may

slightly increase your “Fragmentation” value within the value range of 1500 to 2346. Setting the Fragmentation

value too low may result in poor performance.

Enter a value between 1 and 255 for the Delivery Trafﬁc Indication Message (DTIM). A DTIM is a countdown

informing clients of the next window for listening to broadcast and multicast messages. When the Access

Point has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM

Interval value. AP clients hear the beacons and awaken to receive the broadcast and multicast messages. The

default value for DTIM interval is set to 1.

Transmit Power:

Beacon Interval:

RTS Threshold:

Fragmentation:

DTIM Interval:

Advanced Wireless

Advanced Wireless contains settings which can negatively affect the performance of your router if conﬁgured improperly. Do not change

these settings unless you are already familiar with them or have been instructed to make the change by one of our support personnel.

41D-Link DIR-456 User Manual

Section 3 - Conﬁguration

The Preamble Type deﬁnes the length of the CRC (Cyclic Redundancy Check) block for communication

between the Access Point and roaming wireless adapters. Make sure to select the appropriate preamble type

and click the Apply button.

Note: High network trafﬁc areas should use the shorter preamble type. CRC is a common technique for detecting

data transmission errors.

If all of the wireless devices you want to connect with this access point can connect in the same transmission

mode, you can improve performance slightly by choosing the appropriate “Only” mode. If you have some

devices that use a different transmission mode, choose the appropriate “Mixed” mode.

The “Auto 20/40 MHz” option is usually best. The other options are available for special circumstances.

Using a short guard interval can increase throughput. However, it can also increase error rate in some

installations, due to increased sensitivity to radio-frequency reﬂections. Select the option that works best for

your installation .

Preamble Type:

Wireless Mode:

Band Width:

Short Guard

Interval:

42D-Link DIR-456 User Manual

Section 3 - Conﬁguration

WI-FI PROTECTED SETUP

Select this box to enable the WPS if

wireless devices you wish to include in

the local network support Wi-Fi Protected

Setup.

Only the “Admin” account can change

security settings.

Resets the PIN to the default number

shown on the device.

Generates a new PIN number for the

device.

Click Connect your Wireless Device

to add wireless devices to the wireless

network.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Wi-Fi Protected Setup

Enable:

PIN Settings:

Reset PIN to

Default:

Generate New PIN:

Add Wireless

Station:

Wi-Fi Protected Setup (WPS) is used to easily add devices to a network using a PIN or button press. Devices must support Wi-Fi Protected

Setup in order to be conﬁgured by this method.

If the PIN changes, the new PIN will be used in following Wi-Fi Protected Setup process. Clicking on “Don’t Save Settings” will not reset

the PIN. However, if the new PIN is not saved, it will be lost when the device reboots or loses power.

43D-Link DIR-456 User Manual

Section 3 - Conﬁguration

STEP 1: SELECT CONFIGURATION METHOD

You may select Auto if your device supports WPS. You may select Manual

if you would like to view the current wireless setting for conﬁguring your

device manually.

STEP 2: CONNECT YOUR WIRELESS DEVICE

If Auto conﬁguration is chose, you will be given the option to add a wireless

device using a PIN, or using the Push Button Conﬁguration (PBC).

PIN: Enter the PIN from your wireless device and click the Connect button

on your screen within 120 seconds.

PBC: Press the WPS button on your wireless device and click the Connect

button on your screen within 120 seconds.

If Manual Conﬁguration is chosen, you will see a screen like the one shown

on the right.

Click Next to save your changes, or click Cancel to discard your changes.

44D-Link DIR-456 User Manual

Section 3 - Conﬁguration

UPnP is short for Universal Plug

and Play which is a networking

architecture that provides

compatibility among networking

equipment, software, and

peripherals. The device is a UPnP

enabled router, meaning it will work

with other UPnP devices/software.

If you do not want to use the UPnP

functionality, it can be disabled by

selecting “Disabled”.

When you Enable WAN Ping

respond, you are causing the public

WAN (Wide Area Network) IP

address on the device to respond

to ping commands sent by Internet

users. Pinging public WAN IP

addresses is a common method

used by hackers to test whether

your WAN IP address is valid.

Advanced Network

Advanced Network contains settings which can change the way the router handles certain types of trafﬁc. We recommend that you do

not change any of these settings unless you are already familiar with them or have been instructed to make the change by one of our

support personnel.

Enable UPnP:

Enable WAN Ping Respond:

45D-Link DIR-456 User Manual

Section 3 - Conﬁguration

This allows you to select the speed of the WAN interface of the router. You may select 100Mbps, 10Mbps, or

10/100Mbps Auto.

Enable this option to allow Multicast trafﬁc to pass from the Internet to your network more efﬁciently.

Enable this option if you are receiving video on demand type of service from the Internet. The router uses the

IGMP protocol to support efﬁcient multicasting -- transmission of identical content, such as multimedia, from

a source to a number of recipients. This option must be enabled if any applications on the LAN participate

in a multicast group. If you have a multimedia LAN application that is not receiving content as expected, try

enabling this option.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

WAN Port Speed:

Multicast Streams:

Enable Multicast Streams:

46D-Link DIR-456 User Manual

Section 3 - Conﬁguration

TELEPHONY SETTING

Select this box to enable Caller ID display.

Select this box to enable Caller ID delivery.

Select this box to enable call waiting.

CALL FORWARDING

Select this box to enable the Unconditional

Number. Enter the number in the box provided.

Select this box to enable the Busy Number. Enter

the number in the box provided.

Select this box to enable the No Answer Number. Enter the number in the box provided.

Specify the No Answer Time in seconds.

Select this box to enable the Not Reachable Number. Enter the number in the box provided.

If your mobile service does not support these features, you will see a message at the bottom of the screen

stating No network service or Request was rejected.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Call Setting

Caller ID Display:

Caller ID Delivery:

Call Waiting:

Unconditional Number:

Busy Number:

No Answer Number:

No Answer Timer:

Not Reachable Number:

The Call Setting page allows you to conﬁgure the settings for incoming calls. The DIR-456 allows you to connect a standard landline

telephone and receive calls to the mobile number associated with your SIM card.

47D-Link DIR-456 User Manual

Section 3 - Conﬁguration

ADMINISTRATOR

Enter and conﬁrm the password that the

admin account will use to access the

router’s management interface.

REMOTE MANAGEMENT

Enabling Graphical Authentication make

you router more secure by helping to

prevent against automated attacks.

Remote management allows the DIR-

456 to be conﬁgured from the Internet

using a web browser. A username and

password is still required to access the

Web-Management interface. Usually only

a member of your network can browse the built-in web pages to perform Administrator tasks. This feature

enables you to perform Administrator tasks from the remote (Internet) host.

This is the port number used to access the router.

Example: 8080 is the port used for the Web-Management interface.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Admin

The Admin page allows you to change the Administrator password and enable Remote Management. Admin has read/write access while

the user has read-only access. Only the admin has the ability to change both admin and user account passwords.

Admin Password:

Enable Graphical

Authentication:

Remote Management:

Remote Admin Port:

48D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Time

Select the appropriate Time Zone

from the drop-down box.

Select this checkbox to enter a start

date and an end date for daylight

saving time.

The Network Time Protocol (NTP)

synchronizes the computer’s clock

over a network.

Manually enter the values for Year,

Month, Day, Hour, Minute, and

Second.

This section will help you set the time zone that you are in and the NTP (Network Time Protocol) Server. Daylight Saving can also be

conﬁgured to adjust the time when needed.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

Time Zone:

Enable Daylight Saving:

Automatic Time and Date

Conﬁguration:

Set the Time and Date

Manually:

49D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Enter the e-mail address to be

displayed in the from field of

the e-mail that is send from the

router.

Enter the e-mail address of the

recipient.

Enter the subject of the e-mail to

be sent.

Enter the SMTP server address for

your e-mail account.

Enter the account name for your

e-mail account.

Enter the password associated with the account.

Re-enter the password associated with the account.

Click the Send Mail Now button to send a test message to e-mail address speciﬁed in the To Email Address

ﬁeld.

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

From Email Address:

To Email Address:

Email Subject:

SMTP Server Address:

Account Name:

Password:

Verify Password:

Send Mail Now:

The Email feature can be used to send the system log ﬁles and router alert messages.

Email Settings

50D-Link DIR-456 User Manual

Section 3 - Conﬁguration

System

Use this option to save your current

router configuration settings to a

ﬁle and onto your computer. Click

Save to open a ﬁle dialog, and then

select a location and ﬁle name for

the settings.

Use this option to load the previously

saved router conﬁguration settings.

Browse to ﬁnd the saved ﬁle and then

click Upload Settings to transfer

those settings to the router.

This option will restore all settings

back to their defaults. Any settings

that have not been backed up will be lost, including any rules that you have created.

Click to reboot your router.

Click Clear to clear the language pack that has been installed to the router and restore the default language.

Save To Local Hard Drive:

Load From Local Hard

Drive:

Restore To Factory Default

Settings:

Reboot the Device:

Clear Language Pack:

Here, you can save the current system settings onto the local hard drive.

51D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Firmware

Displays your current firmware

version.

After you have downloaded the new

ﬁrmware, click Browse to locate the

ﬁrmware on your computer.

Click Upload to start the ﬁrmware

upgrade.

Here, you can upgrade the ﬁrmware of your Router. Make sure the ﬁrmware you want to use is on the local hard drive of the computer

and then click Browse to select the ﬁle to be uploaded. Please check the D-Link support site for ﬁrmware updates at http://support.dlink.

com. You can download ﬁrmware upgrades to your hard drive from the D-Link support site.

Current Firmware Version:

Browse:

52D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Dynamic DNS

Dynamic Domain Name System

is a method of keeping a domain

name linked to a changing IP

Address. Select this box to enable

DDNS.

Select your DDNS provider from

the drop-down box.

Enter the Host Name that you

registered with your DDNS

service provider.

Enter the Username for your

DDNS account.

Enter the Password for your

DDNS account.

The DDNS feature allows you to host a server (Web, FTP, or Game Server) using a domain name that you have purchased

(yourname.com) with your dynamically assigned IP address.

Enable Dynamic DNS:

Provider:

Host Name:

Username / E-mail:

Password / Key:

Click Save Settings to save your changes, or click Don’t Save Settings to discard your changes.

53D-Link DIR-456 User Manual

Section 3 - Conﬁguration

System Check

Enter a host name or the IP address

that you want to ping (Packet Internet

Groper) and click Ping.

The status of your Ping attempt

will be displayed in the Ping Result

box.

This useful diagnostic utility can be used to check if a computer is connected to the network. It sends ping packets and listens for responses

from the speciﬁc host.

Host Name or IP Address:

PING Result:

54D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Schedules

The name of the schedule being

deﬁned.

Select a day, range of days, or select

the All Week checkbox to have this

schedule apply every day.

Check this box to have the schedule

active the entire 24 hours on the

days speciﬁed.

Select the time at which you would

like the schedule being deﬁned to

become active.

Select the time at which you would

like the schedule being deﬁned to

become inactive.

This displays all the schedules that

have been deﬁned.

This section allows you to manage schedule rules for various ﬁrewall and parental control features.

Name:

Day(s):

All Day - 24 hrs:

Start Time:

End Time:

Schedule Rules List:

55D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Device Information

All of your Internet and network connection details are displayed on this page. The ﬁrmware version is also displayed here.

Displays the current time and ﬁrmware version.

Displays the MAC address and the private (local)

IP settings for the router.

Displays the MAC address and the public IP

settings for the router.

Displays the wireless MAC address and your

wireless settings such as SSID, Channel, and

Encryption type.

General:

WAN:

LAN:

Wireless LAN:

56D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Logs

Here, you can view logs and deﬁne events that you would like to view.

57D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Statistics

Here you can view the packets transmitted and received passing through your router on both WAN and LAN ports. The trafﬁc counter will

reset if the device is rebooted.

58D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Internet Sessions

This page displays Source and Destination packets passing through the device.

59D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Wireless

This table displays a list of wireless clients that are connected to your wireless router. It also displays the connection time and MAC

address of the connected wireless clients.

60D-Link DIR-456 User Manual

Section 3 - Conﬁguration

Support

61D-Link DIR-456 User Manual

Section 4 - Security

Wireless Security

This section will show you the different levels of security you can use to protect your data from intruders. The

DIR-456 offers the following types of security:

• WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key)

• WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)

• WEP (Wired Equivalent Privacy)

What is WEP?

WEP stands for Wired Equivalent Privacy. It is based on the IEEE 802.11 standard and uses the RC4 encryption algorithm. WEP provides

security by encrypting data over your wireless network so that it is protected as it is transmitted from one wireless device to another.

To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must

determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit

encryption. Keys are deﬁned by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for

Information Interchange – alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember.

The ASCII string is converted to HEX for use over the network. Four keys can be deﬁned so that you can change keys easily.

62D-Link DIR-456 User Manual

Section 4 - Security

Conﬁgure WEP

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity

before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.

1. Log into the web-based conﬁguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on

Wireless Settings on the left side.

2. Next to Security Mode, select Enable WEP Security.

3. Next to Authentication, select Open or Shared Key.

4. Select either 64-bit or 128-bit encryption from the drop-down box next

to WEP Encryption.

5. Next to Key Type, select either Hex or ASCII.

Hex (recommended) - Letters A-F and numbers 0-9 are valid.

ASCII - All numbers and letters are valid.

6. Next to Key 1, enter a WEP key that you create. Make sure you enter

this key exactly on all your wireless devices. You may enter up to 4

different keys.

7. Click Save Settings to save your settings. If you are conﬁguring the router with a wireless adapter, you will lose connectivity until you

enable WEP on your adapter and enter the same WEP key as you did on the router.

63D-Link DIR-456 User Manual

Section 4 - Security

What is WPA?

WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent

Privacy).

The 2 major improvements over WEP:

• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing

algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based

on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.

• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP

regulates access to a wireless network based on a computer’s hardware-speciﬁc MAC address, which is relatively simple

to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized

network users can access the network.

WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between

8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your

wireless router or access point.

WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public

key encryption system to ensure that only authorized network users can access the network.

64D-Link DIR-456 User Manual

Section 4 - Security

Conﬁgure WPA-PSK

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity

before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.

1. Log into the web-based conﬁguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on

Wireless Settings on the left side.

2. Next to Security Mode, select Enable WPA-Personal Security or Enable WPA2-Personal Security.

3. Next to Cipher Mode, select TKIP, AES, or Auto.

4. Next to PSK/EAP, select PSK.

5. Next to Passphrase, enter a key (passphrase). The key is an alpha-

numeric password between 8 and 63 characters long. The password

can include symbols (!?*&_) and spaces. Make sure you enter this

key exactly the same on all other wireless clients.

6. Enter the passphrase again next to Conﬁrmed Passphrase.

7. Click Save Settings to save your settings. If you are conﬁguring the router with a wireless adapter, you will lose connectivity until you

enable WPA-PSK (or WPA2-PSK) on your adapter and enter the same passphrase as you did on the router.

65D-Link DIR-456 User Manual

Section 4 - Security

Conﬁgure WPA (RADIUS)

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity

before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.

1. Log into the web-based conﬁguration by opening a web browser and

entering the IP address of the router (192.168.0.1). Click on Wireless

Settings on the left side.

2. Next to Security Mode, select Enable WPA-Personal Security or Enable

WPA2-Personal Security.

3. Next to Cipher Mode, select TKIP, AES, or Auto.

4. Next to PSK/EAP, select EAP.

5. Next to RADIUS Server 1 enter the IP Address of your RADIUS server.

6. Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port.

7. Next to Shared Secret, enter the security key.

8. If you have a secondary RADIUS server, enter its IP address, port, and secret key.

9. Click Apply Settings to save your settings.

66D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

Using Windows® 7 and WPS for Wireless Conﬁguration

The following steps allow you to conﬁgure your DIR-456 wireless network settings using Windows® 7 through WPS.

1. Click the Start button and select Computer from the Start

menu.

2. Click the Network option.

67D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

3. Double-click the DIR-456 router.

4. Input the WPS PIN number (displayed in the Advanced >

Wi-Fi Protected Setup section in the Router’s Web UI) and

click Next.

68D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

5. Type a name for your wireless network.

6. To conﬁgure advanced settings, click the icon.

Click Next to continue.

69D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

7. The following window will appear while the Router is being

conﬁgured.

Wait for the conﬁguration to complete.

8. After conﬁguration is complete, a window will appear that your

wireless network has been set up successfully.

Make a note of the security key as you may need to provide

this security key when adding an older wireless device to the

network in the future.

Click Close to complete WPS setup.

70D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

Connecting to a Wireless Network

Using Windows® 7

It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before

conﬁguring your wireless adapter. If you are joining an existing network, you will need to know the security key or

passphrase being used.

2. The utility will display any available wireless networks in

your area.

1. Click on the wireless icon in the system tray in the lower-

right corner of your screen.

Wireless Icon

71D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

3. Highlight the wireless network (SSID) you would like to

connect to and click the Connect button.

4. The following window appears while your computer tries

to connect to the router.

72D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

5. If your wireless network uses encryption such as WEP or

WPA/WPA2, enter the encryption password/passphrase

for your wireless network and click Connect.

It may take 20-30 seconds to connect to the wireless

network. If the connection fails, please verify that the key

or passphrase is exactly the same as on the wireless

router.

73D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

Connecting to a Wireless Network Using Windows Vista®

It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before

conﬁguring your wireless adapter. If you are joining an existing network, you will need to know the security key or

passphrase being used.

2. The utility will display any available wireless networks

in your area.

Highlight the wireless network (SSID) you would like to

connect to and click Connect.

If you get a good signal but cannot access the Internet,

check your TCP/IP settings for your wireless adapter.

Refer to the Networking Basics section in this manual

for more information.

1. Open the Windows Vista® Wireless Utility by right-clicking

on the wireless computer icon in the system tray in the

lower right corner of the screen. Select Connect to a

network.

74D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

3. If your wireless network uses encryption such as WEP or WPA/

WPA2, enter the encryption password/passphrase for your wireless

network and click Connect.

It may take 20-30 seconds to connect to the wireless network. If the

connection fails, please verify that the key or passphrase is exactly

the same as on the wireless router.

75D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

Connecting to a Wireless Network

Using Windows® XP

Windows® XP users may use the built-in wireless utility (Zero Conﬁguration Utility). The following instructions are for

Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual

of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option

similar to the Windows® XP utility as seen below.

1. If you receive the Wireless Networks Detected bubble, click

on the center of the bubble to access the utility.

Right-click on the wireless computer icon in the system tray

in the lower-right corner of the screen. Select View Available

Wireless Networks.

2. The utility will display any available wireless networks in your

area. Click on a network (displayed using the SSID) and click

the Connect button.

If you get a good signal but cannot access the Internet,

check you TCP/IP settings for your wireless adapter. Refer

to the Networking Basics section in this manual for more

information.

76D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

3. If your wireless network uses encryption such as WEP or WPA/

WPA2, enter the encryption password/passphrase for your wireless

network and click Connect.

It may take 20-30 seconds to connect to the wireless network. If the

connection fails, please verify that the key or passphrase is exactly

the same as on the wireless router.

77D-Link DIR-456 User Manual

Section 6 - Troubleshooting

Troubleshooting

This chapter provides solutions to problems that can occur during the installation and operation of the DIR-456. Read the following

descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system,

the screenshots on your computer will look similar to the following examples.)

1. Why can’t I access the web-based conﬁguration utility?

When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on the Internet or have

to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same

IP subnet to connect to the web-based utility.

• Make sure you have an updated Java-enabled web browser. We recommend the following:

• Internet Explorer 6.0 or higher

• Netscape 8 or higher

• Mozilla 1.7.12 (5.0) or higher

• Opera 8.5 or higher

• Safari 1.2 or higher (with Java 1.3.1 or higher)

• Camino 0.8.4 or higher

• Firefox 1.5 or higher

• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or

connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.

• Disable any internet security software running on the computer. Software ﬁrewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal

Firewall, and Windows® XP ﬁrewall may block access to the conﬁguration pages. Check the help ﬁles included with your ﬁrewall software

for more information on disabling or conﬁguring it.

78D-Link DIR-456 User Manual

Section 6 - Troubleshooting

• Conﬁgure your Internet settings:

• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button

to restore the settings to their defaults.

• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure

nothing is checked. Click OK.

• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.

• Close your web browser (if open) and open it.

• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should

open the login page for your the web management.

• If you still cannot access the conﬁguration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and

try accessing the conﬁguration. If you have multiple computers, try connecting using a different computer.

2. What can I do if I forgot my password?

If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory

defaults.

To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the

button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the

router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.

79D-Link DIR-456 User Manual

Appendix A - Wireless Basics

D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within

your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products

will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless

networking delivers.

A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires.

Wireless LANs are used increasingly in both home and ofﬁce environments, and public areas such as airports, coffee shops and universities.

Innovative ways to utilize WLAN technology are helping people to work and communicate more efﬁciently. Increased mobility and the

absence of cabling and other ﬁxed infrastructure have proven to be beneﬁcial for many users.

Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems

support the same protocols as Ethernet adapter cards.

Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers,

printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link.

Wireless Basics

80D-Link DIR-456 User Manual

Appendix A - Wireless Basics

What is Wireless?

Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency

to connect wirelessly, so you have the freedom to connect computers anywhere in your home or ofﬁce network.

Why D-Link Wireless?

D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products.

D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.

How does wireless work?

Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless

technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to

connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal

Area Network (WPAN).

Wireless Local Area Network (WLAN)

In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small

antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture,

the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing

plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.

Wireless Personal Area Network (WPAN)

Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet

away.

81D-Link DIR-456 User Manual

Appendix A - Wireless Basics

Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power

which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate

on batteries.

Who uses wireless?

Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, ofﬁce, business, D-Link

has a wireless solution for it.

Home

• Gives everyone at home broadband access

• Surf the web, check e-mail, instant message, and etc

• Gets rid of the cables around the house

• Simple and easy to use

Small Ofﬁce and Home Ofﬁce

• Stay on top of everything at home as you would at ofﬁce

• Remotely access your ofﬁce network from home

• Share Internet connection and printer with multiple computers

• No need to dedicate ofﬁce space

82D-Link DIR-456 User Manual

Appendix A - Wireless Basics

Where is wireless used?

Wireless technology is expanding everywhere not just at home or ofﬁce. People like the freedom of mobility and it’s becoming so popular

that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually

called “hotspots”.

Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like Airports,

Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.

Wireless network is easy to setup, but if you’re installing it for the ﬁrst time it could be quite a task not knowing where to start. That’s why

we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.

Tips

Here are a few things to keep in mind, when you install a wireless network.

Centralize your Router or Access Point

Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/

access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may

need a repeater to boost the signal to extend the range.

Eliminate Interference

Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point.

This would signiﬁcantly reduce any interference that the appliances might cause since they operate on same frequency.

Security

Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or

WEP security feature on the router. Refer to product manual for detail information on how to set it up.

83D-Link DIR-456 User Manual

Appendix A - Wireless Basics

There are basically two modes of networking:

• Infrastructure – All wireless clients will connect to an access point or wireless router.

• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on

each computer, such as two or more WNA-2330 wireless network Cardbus adapters.

An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless

router or access point.

An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to

communicate.

Wireless Modes

84D-Link DIR-456 User Manual

Appendix B - Networking Basics

Networking Basics

Check your IP address

After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e.

wireless router) automatically. To verify your IP address, please follow the steps below.

Click on Start > Run. In the run box type cmd and click

OK. (Windows® Vista™ users type cmd in the Start Search

box.)

At the prompt, type ipconﬁg and press Enter.

This will display the IP address, subnet mask, and the

default gateway of your adapter.

If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some ﬁrewall software programs

may block a DHCP request on newly installed adapters.

85D-Link DIR-456 User Manual

Appendix B - Networking Basics

Statically Assign an IP address

If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:

Step 1

Windows® Vista™ - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network

Connections.

Windows® XP - Click on Start > Control Panel > Network Connections.

Windows® 2000 - From the desktop, right-click My Network Places > Properties.

Step 2

Right-click on the Local Area Connection which represents your network adapter and select Properties.

Step 3

Highlight Internet Protocol (TCP/IP) and click Properties.

Step 4

Click Use the following IP address and enter an IP address that is on the same subnet as your

network or the LAN IP address on your router.

Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where

X is a number between 2 and 99. Make sure that the number you choose is not in use on the

network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1).

Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary

DNS is not needed or you may enter a DNS server from your ISP.

Step 5

Click OK twice to save your settings.

86D-Link DIR-456 User Manual

Appendix C - Technical Speciﬁcations

Technical Speciﬁcations

GSM Band (GSM/GPRS/EDGE)

850 / 900 / 1800 / 1900 MHz 

Power Class 4 (850 / 900 MHz) 

Power Class 1 (1800 / 1900 MHz) 

UMTS/HSDPA Band *

850 / 1900 / 2100 MHz 

Power Class 3 

Data Rates **

6/9/11/12/18/24/36/48/54Mbps in 802.11g mode 

1/2/5.5/11Mbps in 802.11b mode 

Standards

802.11g 

802.11b 

802.3 

802.3u 

Wireless Security

64/128-bit WEP (Wired Equivalent Privacy) 

WPA & WPA2 (Wi-Fi Protected Access) 

Firewall

Network Address Translation (NAT) 

Stateful Packet Inspection (SPI) 

VPN

L2TP/PPTP/IPSEC VPN Pass-through 

5 Dedicated IPSec tunnels 

Antenna

3 Internal antennas 

Ports

2 x LAN (RJ-45) 

1 x WAN (RJ-45) 

1 x Phone (RJ-11) 

USIM Slot

Standard 6-pin SIM card interface 

LED Status Indicators

WPS 

WAN 

LAN 

WLAN 

2G/2.5G 

3G/3.5G 

SMS 

Signal 

3 Internal antennas (2 for 3G, 1 for WIFI)

87D-Link DIR-456 User Manual

Appendix C - Technical Speciﬁcations

Dimensions (L x W x H)

184 x 125 x 30 mm 

Operating Temperature

0˚ to 40˚C (32˚ to 104˚F) 

Operating Humidity

10%-95% (Non-condensing) 

Certiﬁcation

CE 

FCC 

* Supported frequency band is dependent upon regional hardware version.

** Maximum wireless signal rate derived from IEEE Standard 802.11g speciﬁcations. Actual data throughput will vary. Network conditions and

environmental factors, including volume of network trafﬁc, building materials and construction, and network overhead, lower actual data throughput

rate. Environmental factors will adversely affect wireless signal range.

. CE

. FCC

. NCC

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1

through 11.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

אՀᤞ፿ᔞش؀᨜چ೴!

ᆖীڤᎁᢞٽ௑հ܅פ෷୴᙮ሽᖲΔॺᆖ๺ױΔֆ׹Ε೸ᇆࢨࠌشृ݁լ൓ᖐ۞᧢ޓ᙮෷ΕףՕפ

෷ࢨ᧢ޓ଺๻ૠհ௽ࢤ֗פ౨Ζʳ

܅פ෷୴᙮ሽᖲհࠌشլ൓ᐙ᥼ଆ౰ڜ٤֗եឫٽऄຏॾΙᆖ࿇෼ڶեឫ෼ွழΔᚨمܛೖشΔࠀ

ޏ࿳۟ྤեឫழֱ൓ᤉᥛࠌشΖছႈٽऄຏॾΔਐࠉሽॾऄ๵ࡳ܂ᄐհྤᒵሽຏॾΖ܅פ෷୴᙮ሽ

ᖲႊݴ࠹ٽऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭شሽंᘿ୴ࢤሽᖲ๻ໂհեឫΖʳ

྇֟ሽ጖ंᐙ᥼Δᓮݔᔞࠌش!

D Link DIR456A1 Residential USIM Embedded HSDPA 3G Router User Manual Manual v1 00 FCC NCC

D Link Corporation Residential USIM Embedded HSDPA 3G Router Manual v1 00 FCC NCC

User Manual

Navigation menu

Namespaces

Views

Navigation