D Link DIR605B1 Wireless N Router User Manual 0595459

D Link Corporation Wireless N Router 0595459

UserManual.wiki >

DIR605B1 User Manual

Manual

2D-Link DIR-615 User ManualTable of ContentsPackage Contents ....................................................... 4System Requirements ............................................. 4Features .................................................................. 5Hardware Overview ................................................. 6Connections....................................................... 6LEDs .................................................................. 7Installation.................................................................... 8Before you Begin ..................................................... 8Wireless Installation Considerations........................ 9Wall Mounting Your Device ................................... 10Connect to Cable/DSL/Satellite Modem ................ 11Connect to Another Router.................................... 12Conﬁguration............................................................. 14Web-based Conﬁguration Utility ............................ 14Setup Wizard ................................................... 15Static (assigned by ISP)............................... 19Internet Setup .................................................. 20Dynamic ....................................................... 20PPPoE ......................................................... 21PPTP............................................................ 22L2TP............................................................. 23Dual Access (for Russia only) ...................... 24Wireless Setup................................................. 25LAN Setup ....................................................... 31DHCP Server Settings ..................................... 32Time and Date ................................................. 33Parental Control............................................... 34Port Forwarding ............................................... 35Application Rules ............................................. 36Access Control................................................. 37Firewall & DMZ ................................................ 38Advanced Wireless .......................................... 39Advanced Network........................................... 40Advanced Network........................................... 40Routing ............................................................ 41Device Administration ...................................... 42Save and Restore ............................................ 43Firmware Update ............................................. 44DDNS Setting .................................................. 45System Check.................................................. 46Schedules ........................................................ 47Log Settings..................................................... 48Device Info....................................................... 49Log................................................................... 50Statistics .......................................................... 51Active Session ................................................ 51Table of Contents

3D-Link DIR-615 User ManualTable of ContentsWireless ........................................................... 52Help ................................................................. 53Wireless Security....................................................... 54What is WEP? ....................................................... 54Conﬁgure WEP...................................................... 55What is WPA? ....................................................... 56Conﬁgure WPA-PSK and WPA2-PSK................... 57Conﬁgure WPA/WPA2-PSK .................................. 58Conﬁgure WPA, WPA2, and WPA/WPA2 (RADIUS).............................................................................. 59Connect to a Wireless Network................................ 60Using Windows® XP............................................... 60Conﬁgure WEP...................................................... 61Conﬁgure WPA-PSK ............................................. 63Setting Up Wi-Fi Protection...................................... 65(WCN 2.0 in Windows Vista)..................................... 65Initial Router Conﬁguration for Wi-Fi Protection .... 65Setting Up a Conﬁgured Router ............................ 66Changing the Computer Name and Joining a Workgroup ................................................................. 67Conﬁguring the IP Address in Vista ........................ 69Setting Up a Connection or Network Wirelessly .... 72Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK)........................................... 77Connecting to an Unsecured Wireless Network..... 81Troubleshooting ........................................................ 85Wireless Basics ......................................................... 89What is Wireless?.................................................. 90Tips........................................................................ 92Wireless Modes ..................................................... 93Networking Basics .................................................... 94Check your IP address .......................................... 94Statically Assign an IP address ............................. 95Technical Speciﬁcations........................................... 96Warranty.....................................................................98

4D-Link DIR-615 User ManualSection 1 - Product Overview• D-Link DIR-615 Wireless Router• Power Adapter• Ethernet Cable• Manual and Warranty on CDSystem Requirements• Ethernet-based Cable or DSL Modem• Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet adapter• Internet Explorer 6 or Firefox 2.0 or above (for conﬁguration)Package ContentsNote: Using a power supply with a different voltage rating than the one included with the DIR-615 will cause damage and void the warranty for this product.Note: Always attach the power cord plug to the power supply, before inserting the power cord and connected power supply to the wall outlet.

5D-Link DIR-615 User ManualSection 1 - Product Overview• Faster Wireless Networking - The DIR-615 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. • Compatible with 802.11b and 802.11g Devices - The DIR-615 is still fully compatible with the IEEE 802.11b and IEEE 802.11g standard, so it can connect with existing 802.11b and IEEE 802.11g PCI, USB and Cardbus adapters.• Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features including: • Content Filtering - Easily applied content ﬁltering based on MAC Address, URL, and/or Domain Name.• Filter Scheduling - These ﬁlters can be scheduled to be active on certain days or for a duration of hours or minutes.• Secure Multiple/Concurrent Sessions - The DIR-615 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-615 can securely access corporate networks.• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-615 lets you control what information is accessible to those on the wireless network, whether from the Internet or from your company’s server. Conﬁgure your router to your speciﬁc settings within minutes.* Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n speciﬁcations. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trafﬁc, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range.Features

6D-Link DIR-615 User ManualSection 1 - Product OverviewPressing the Reset Button restores the router to its original factory default settings.Receptor for the Power Adapter.The Auto MDI/MDIX WAN port is the connection for the Ethernet cable to the Cable or DSL modem.LAN PortsConnect Ethernet devices such as computers, switches, and hubs.Hardware OverviewConnections

7D-Link DIR-615 User ManualSection 1 - Product OverviewHardware OverviewLEDsINTERNETA solid light indicates connection on the WAN port. This LED blinks during data transmission.WLAN LEDA solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission.Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission.Power LEDA solid light indicates a proper connection to the power supply.

8D-Link DIR-615 User ManualSection 2 - InstallationBefore you BeginInstallationThis section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Please conﬁgure the router with the computer that was last connected directly to your modem. Also, you can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the WAN port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet). If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Ethernet 300 from your computer or you will not be able to connect to the Internet.

9D-Link DIR-615 User ManualSection 2 - InstallationWireless Installation ConsiderationsThe D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (ﬁsh tanks), mirrors, ﬁle cabinets, brick, and concrete will degrade your wireless signal.4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use.

11D-Link DIR-615 User ManualSection 2 - InstallationIf you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer.3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the WAN port on the router.4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your computer.5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds). 6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router to boot. 7. Turn on your computer. 8. Verify the link lights on the router. The power light, WAN light, and the LAN light (the port that your computer is plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable connections are correct. 9. Skip to page 16 to conﬁgure your router. Connect to Cable/DSL/Satellite Modem

12D-Link DIR-615 User ManualSection 2 - InstallationIf you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network:• Disable UPnP™• Disable DHCP• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router.To connect to another router, please follow the steps below:1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer.2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to admin and leave the password box empty. Click OK to continue.3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settingsto continue. 4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save Settings to continue.5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your settings. Use this new IP address to access the conﬁguration utility of the router in the future. Close the browser and change your computer’s IP settings back to the original values as in Step 1.Connect to Another Router

13D-Link DIR-615 User ManualSection 2 - Installation6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the WAN port of the D-Link router. 8. You may now use the other three LAN ports to connect other Ethernet devices and computers. To conﬁgure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Conﬁgurationand Wireless Security sections for more information on setting up your wireless network.

14D-Link DIR-615 User ManualSection 3 - ConﬁgurationConﬁgurationThis section will show you how to conﬁgure your new D-Link wireless router using the web-based conﬁguration utility.Web-based Conﬁguration UtilityTo access the conﬁguration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).Enter the user name (admin) and your password. Leave the password blank by default.If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.

15D-Link DIR-615 User ManualSection 3 - ConﬁgurationSetup WizardYou may run the setup wizard from the opening Internet Setup window to quickly set up your router. Click Internet Connection Setup Wizard,you will be directed to the ﬁrst window of the wizard.Click Next to continue.Create a new password and then click Next to continue.

16D-Link DIR-615 User ManualSection 3 - ConﬁgurationSelect your time zone from the drop-down menu and then click Nextto continue.Select the type of Internet connection you use and then click Nextto continue.If you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue.The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.

17D-Link DIR-615 User ManualSection 3 - ConﬁgurationIf you selected PPPoE, enter your PPPoE username and password. Click Next to continue.Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.If you selected PPTP, enter your PPTP username and password. Click Next to continue.If you selected L2TP, enter your L2TP username and password. Click Nextto continue.

18D-Link DIR-615 User ManualSection 3 - ConﬁgurationIf you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue.Click Connect to save your settings.If you selected Big Pond, enter your Big Pond username and password. Click Next to continue.Please allow 1-2 minutes for rebooting. When the router has ﬁnished rebooting, the opening window will be displayed.

19D-Link DIR-615 User ManualSection 3 - ConﬁgurationEnter the IP address assigned by your ISP.Enter the Subnet Mask assigned by your ISP.Enter the Gateway assigned by your ISP.The default MAC Address is set to the WAN’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.The default MAC address is set to the WAN’s physical interface MAC address on the Broadband Router. You can use the Clone MAC Address button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP.Enter the Primary DNS server IP address assigned by your ISP.This is optional.Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1492is the default MTU.IP Address:Subnet Mask:ISP Gateway:MAC Address:Clone MAC Address:Primary DNS Address:Secondary DNS Address:MTU:Internet SetupStatic (assigned by ISP)Select Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the ﬁelds must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

20D-Link DIR-615 User ManualSection 3 - ConﬁgurationChoose Dynamic IP Address to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services.The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.The default MAC Address is set to the WAN’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.The default MAC address is set to the WAN’s physical interface MAC address on the Broadband Router. You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP.Enter the DNS (Domain Name Server) server IP address assigned by your ISP. Dynamic IP Address:HostName:MAC Address:Internet SetupDynamicClone MAC Address: DNS Addresses:MTU: Maximum Transmission Unit - You may need to change the MTU for optimal performance with your speciﬁc ISP.Access PointMode:Checking this box disables NAT and turns the Router into an Access Point only.To manually set up the Internet connection, click the Manual Internet Connection Setup button on the Router’s opening window.

21D-Link DIR-615 User ManualSection 3 - ConﬁgurationSelect Dynamic (most common) or Static. Select Staticif your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Enter the IP address (Static PPPoE only).Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Maximum Transmission Unit - You may need to change the MTU for optimal performance with your speciﬁc ISP. 1492is the default MTU.Select either Always-on, Manual, or Connect-ondemand.PPPoE:User Name:Password:Service Name:IP Address:DNS Addresses:Maximum Idle Time:MTU:ConnectionMode Select:Internet SetupPPPoE Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.

22D-Link DIR-615 User ManualSection 3 - ConﬁgurationSelect Dynamic (most common) or Static. Select Staticif your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.Enter the IP address (Static PPTP only).Enter the Primary and Secondary DNS Server Addresses (Static PPTP only).Enter the Gateway IP Address provided by your ISP.The DNS server information will be supplied by your ISP (Internet Service Provider.)Enter the Server IP provided by your ISP (optional).Enter your PPTP account name.Enter your PPTP password and then retype the password in the next box.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Maximum Transmission Unit - You may need to change the MTU for optimal performance. Select either Always-on, Manual, or Connect-on demand.PPTP:IP Address:Subnet Mask:Gateway:DNS:Internet SetupPPTPChoose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Server IP:PPTP Account:PPTP Password:Maximum Idle Time:MTU:Connect Mode:

23D-Link DIR-615 User ManualSection 3 - ConﬁgurationSelect Dynamic (most common) or Static. Select Staticif your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.Enter the IP address (Static L2TP only).Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).Enter the Gateway IP Address provided by your ISP.The DNS server information will be supplied by your ISP (Internet Service Provider.)Enter the Server IP provided by your ISP (optional).Enter your L2TP account name.Enter your L2TP password and then retype the password in the next box.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Maximum Transmission Unit - You may need to change the MTU for optimal performance with your speciﬁc ISP. Select either Always-on, Manual, or Connect-on demand.L2TP:IP Address:Subnet Mask:Gateway:DNS:Server IP:L2TP Account:L2TP Password:Maximum Idle Time:MTU:Connect Mode:Internet SetupL2TPChoose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.

24D-Link DIR-615 User ManualSection 3 - ConﬁgurationInternet SetupDual Access (for Russia only)There are two main steps to conﬁgure a Dual Access Internet connection for Russia. First, conﬁgure a PPPoE connection (as previously described for PPPoE connections), and add the physical WAN IP settings as instructed from the ISP. Second, conﬁgure a PPTP connection (as previously described for PPTP connections). In addition, the second step also includes an option to use a MAC address that will always be associated with the connection. The MAC address is entered manually or copied from the computer.

25D-Link DIR-615 User ManualSection 3 - ConﬁgurationWireless SetupWireless settings for the router may be conﬁgured manually or by using a wizard. To use the wizard, click the Wireless Connection Setup Wizard button and then follow the steps that are described below. To conﬁgure the wireless settings manually, click the Manual Wireless Connection Setup button. The parameters for this window are described later in this section. The Wireless Security section that directly follows this Conﬁguration section provides additional explanation for how to conﬁgure the WEP, WPA, WPA2, and WPA/WPA2 wireless security mode options. Click Next to continue.Enter a Wireless Network Name in the textbox, which is also know as the SSID, and then click Next to continue.

26D-Link DIR-615 User ManualSection 3 - ConﬁgurationUse the radio buttons to select the desired level of wireless security, Best, Better, or Good, and then click Next to continue.Enter a Wireless Security Password in the textbox and then click Next to continue.This window displays a summary of your wireless security settings. Please print this out or record this information in a safe place and then click Saveto continue.The Router will save your new settings and reboot. When it is ﬁnished after 1-2 minutes, the opening Wireless Setup window is displayed.

27D-Link DIR-615 User ManualSection 3 - ConﬁgurationTo implement Wi-Fi protection, or WCN 2.0, tick the Enable checkbox, click either Generate New PIN or Reset PIN to Default, and then conﬁgure the Wi-Fi settings below. Please see the Setting Up Wi-Fi Protection (WCN 2.0 in Windows Vista) section later in this manual for detailed conﬁguration information.Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.Service Set Identiﬁer (SSID) is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive.Indicates the channel setting for the DIR-615. By default the channel is set to 6. The Channel can be changed to ﬁt the channel setting for an existing wireless network or to customize the wireless network. The Auto Channel Selection setting can be selected to allow the DIR-615 to choose the channel with the least amount of interference.Use the drop-down menu to select the appropriate Transmission Rate in Mbits per second. Many users will want to use the default setting, Best (automatic).Enable Wi-Fi Multimedia to enjoy basic quality of service features. WMM prioritizes trafﬁc according to four access categories: voice, video, best effort, and background. Check this option if you would not like the SSID of your wireless network to be broadcasted by the DIR-615. If this option is checked, the SSID of the DIR-615 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-615 in order to connect to it.Wi-Fi Protected Setup:EnableWireless Channel:Wireless Network Name:Transmission Rate:WMM Enable:Enable Wireless:Enable Hidden Wireless:

28D-Link DIR-615 User ManualSection 3 - Conﬁguration1. To enable wireless security on the Router, usethe drop-down menu to select the desired option. To enable WEP, select Enable WEP Wireless Security (basic).2. Next to Authentication, select either Open or Shared Key. Shared Key provides greater security.3. Select either 64Bit or 128Bit encryption from the drop-down menu next to WEP Encryption.4. Next to Default Key Type, select WEP Key 1 andenter a WEP key that you create. Make sure you enter this key exactly on all your wireless devices. You may enter up to four different keys either using Hex or ASCII.Hex is recommended (letters A-F and numbers 0-9 are valid). In ASCII all numbers and letters are valid.5. Click Save Settings to save your settings. If you are conﬁguring the Router with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the Router.NOTE:It is recommended to enable encryption on your wireless Router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.

29D-Link DIR-615 User ManualSection 3 - Conﬁguration1. To enable WPA, WPA2, or WPA/WPA2, select either Enable WPA Only Wireless Security (enhanced), Enable WPA2 Only Wireless Security (enhanced), or Enable WPA/WPA2 Wireless Security (enhanced).2. Next to Cipher Type, select TKIP,AES,orBoth.3. Next to PSK/EAP, select PSK.4. Next to Network Key, enter a passphrase. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. Make sure you enter this key exactly the same on all other wireless clients.5. Click Save Settings to save your settings. If you are conﬁguring the router with a wireless adapter, you will lose connectivity until you enable WPA, WPA2, or WPA/WPA2 (whichever of the three options you have selected above) on your adapter and enter the same network key as you did on the router.

30D-Link DIR-615 User ManualSection 3 - Conﬁguration1. To enable WPA, WPA2, or WPA/WPA2 for a RADIUS server, next to Security Mode, select Enable WPA Only Wireless Security (enhanced), Enable WPA2 Only Wireless Security (enhanced), or Enable WPA/WPA2 Wireless Security (enhanced).2. Next to Cipher Type, select TKIP, AES,orAuto.3. Next to PSK/EAP, select EAP.4. Next to RADIUS Server 1 enter the IP Addressof your RADIUS server.5. Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port.6. Next to Shared Secret, enter the security key.7. If you have a secondary RADIUS server, enter its IP address, port, and secret key.8. Click Save Settings to save your settings.

31D-Link DIR-615 User ManualSection 3 - ConﬁgurationThis section will allow you to change the local network settings of the router and to conﬁgure the DHCP settings.LAN SetupEnter the IP address of the router. The default IP address is 192.168.0.1.If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the conﬁguration utility.Enter the Subnet Mask. The default subnet mask is 255.255.255.0.Enter the Domain name (Optional).Check the box to transfer the DNS server information from your ISP to your computers. If unchecked, your computers will use the router for a DNS server.Router IPAddress:Default Subnet Mask:Local Domain Name:Enable DNS Relay:Refer to the next page for DHCP information.

32D-Link DIR-615 User ManualSection 3 - ConﬁgurationCheck the box to enable the DHCP server on your router. Uncheck to disable this function.Enter the starting and ending IP addresses for the DHCP server’s IP assignment.The length of time for the IP address lease. Enter the Lease time in minutes.Enable DHCP Server:DHCP IPAddress Range:DHCP Lease Time:DHCP Server SettingsDHCP stands for Dynamic Host Control Protocol. The DIR-615 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-615. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.

33D-Link DIR-615 User ManualSection 3 - ConﬁgurationThis section will allow you to conﬁgure, update, and maintain the correct time on the internal system clock.Time and DateSelect the Time Zone from the drop-down menu.Ticking this checkbox enables Daylight Saving time. Click Sync. your computer’s time settings to copy your PC’s time settings.Tick the “Automatically synchronize with D-Link’s Internet time server” checkbox and then use the drop-down menu to select an NTP Server. NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. To manually input the time, enter the values in these ﬁelds for the Year, Month, Day, Hour, Minute, and Second. Click Save Settings.TimeZone:Enable Daylight Saving:NTPServerUsed:Manual:

34D-Link DIR-615 User ManualSection 3 - ConﬁgurationThis feature allows you to create a list of websites that you want to either allow or deny users access.Parental ControlSelect Turn Parental Control OFF, Turn Parental Control ON and ALLOW computers access to ONLY these sites, or Turn Parental Control ON and DENY computers access to ONLY these sites.Enter the keywords or URLs that you want to block (or allow). Any URL with the keyword in it will be blocked.The schedule of time when the parental control ﬁlter will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Maintenance > Schedulessection.Conﬁgure Parental Control:Website URL:Schedule:

35D-Link DIR-615 User ManualSection 3 - ConﬁgurationPort ForwardingThis will allow you to open a single port or a range of ports.Check the box to enabled the rule. Enter a name for the rule.Enter the IP address of the computer on your local network that you want to allow the incoming service to.Enter the port or ports that you want to open. If you want to open one port, enter the same port in both boxes.Select TCP, UDP, or AnyRule:Name:IP Address:Start Port/End Port:Trafﬁc Type:

36D-Link DIR-615 User ManualSection 3 - ConﬁgurationApplication RulesSome applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difﬁculties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-615.Check the box to enable the rule. Enter a name for the rule.This is the port used to trigger the application. It can be either a single port or a range of ports.This is the port number on the WAN side that will be used to access the application. You may deﬁne a single port or a range of ports. You can use a comma to add multiple ports or port ranges.Select TCP, UDP, or Any.Rule:Name:Trigger Port:Firewall Port:Trafﬁc Type:

37D-Link DIR-615 User ManualSection 3 - ConﬁgurationAccess ControlSelect Turn MAC Filtering OFF, Turn MAC Filtering ON and ALLOW computers listed to access the network, or Turn MAC Filtering ON and DENY computers listed to access the network.Enter the MAC address you would like to ﬁlter.To ﬁnd the MAC address on a computer, please refer to the Networking Basics section in this manual.Select a DHCP client from the drop-down menu and click the arrow to copy that MAC Address. The schedule of time when the network ﬁlter will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Maintenance > Schedules section.Conﬁgure MAC Filter:MAC Address: DHCP Client List:Schedule:Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.

38D-Link DIR-615 User ManualSection 3 - ConﬁgurationFirewall & DMZThis section will allow you to set up a DMZ host and to set up ﬁrewall rules.If you have a client PC that cannot run Internet applications properly from behind the DIR-615, then you can set the client up for unrestricted Internet access. It allows a computer to be exposed to the Internet. This feature is useful for gaming purposes. Enter the IP address of the internal computer that will be the DMZ host. Adding a client to the DMZ (Demilitarized Zone) may expose your local network to a variety of security risks, so only use this option as a last resort.Check this to enable SPI.Check this box to enable DMZ.Enter the IP address of the computer you would like to open all ports to.Choose a name for the ﬁrewall rule.Select to Allow or Deny transport of the data packets according to the criteria deﬁned in the rule. The Source/Destination is the TCP/UDP port on either the LAN or WAN side.Click Add New to access the Schedules window. See Maintenance>Schedules for more information.Enter a beginning and ending IP address.Select the transport protocol that will be used for the ﬁlter rule.Enter the desired port range for the ﬁlter rule.Enable DMZ Host:DMZ IP Address:Name:Action:Source/Dest:Schedule:IP Address:Protocol:Port Range: Enable SPI:

39D-Link DIR-615 User ManualSection 3 - ConﬁgurationSet the transmit power of the antennas.Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended.This value should remain at its default setting of 2346. If inconsistent data ﬂow is a problem, only a minor modiﬁcation should be made.The fragmentation threshold, which is speciﬁed in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting.(Delivery Trafﬁc Indication Message) 1 is the default setting. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages.Select Short or Long Preamble. The Preamble deﬁnes the length of the CRC block (Cyclic Redundancy Check is a common technique for detecting data transmission errors) for communication between the wireless router and the roaming wireless network adapters. Auto is the default setting. Note: High network trafﬁc areas should use the shorter preamble type.CTS (Clear To Send) is a function used to minimize collisions among wireless devices on a wireless local area network (LAN). CTS will make sure the wireless network is clear before a wireless client attempts to send wireless data. Enabling CTS will add overhead and may lower wireless through put. None: CTS is typically used in a pure 802.11g environment. If CTS is set to “None” in a mixed mode environment populated by 802.11b clients, wireless collisions may occur frequently. Always: CTS will always be used to make sure the wireless LAN is clear before sending data. Auto: CTS will monitor the wireless network and automatically decide whether to implement CTS based on the amount of trafﬁc and collisions that occurs on the wireless network.Select one of the following:Mixed 802.11g and 802.11b - Select if you are using both 802.11b and 802.11g wireless clients.802.11n Only - Select only if all of your wireless clients are 802.11n.Mixed 802.11n, 802.11b, and 802.11g - Select if you are using a mix of 802.11n, 11g, and 11b wireless clients.Select the Channel Width:Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.20MHz - Select if you are not using any 802.11n wireless clients. This is the default setting. Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.Transmit Power:Beacon interval:RTS Threshold:Fragmentation:DTIM Interval:Preamble Type:CTS Mode:802.11 Mode:Channel Width:Short GI:Advanced WirelessThis window allows you to change the behavior of the 802.11g wireless radio from the standard settings. Please be aware that any changes to the factory default settings may adversely affect the behavior of your network.

40D-Link DIR-615 User ManualSection 3 - ConﬁgurationTo use the Universal Plug and Play (UPnP™)feature tick this checkbox. UPNP provides compatibility with networking equipment, software and peripherals.Unchecking the box will not allow the DIR-615 to respond to Pings. Blocking the Ping may provide some extra security from hackers. Tick this checkbox to allow the WAN port to be “Pinged”.You may set the port speed of the WAN port to 10Mbps, 100Mbps, or 10/100Mbps Auto. Some older cable or DSL modems may require you to set the port speed to 10Mbps.Enable UPnP:Enable WAN Ping Respond:WAN PortSpeed:Advanced NetworkThis window allows you to change the LAN settings. Please be aware that any changes to the factory default settings may affect the behavior of your network.

41D-Link DIR-615 User ManualSection 3 - ConﬁgurationTick this checkbox to enable or disable ﬁxed routes to deﬁned destinations.Use the drop-down menu to choose the WAN or WAN (Physical Port) Interface the IP packet must use to transit out of the Router.The IP address of the packets that will take this route.The subnet of the IP address of the packets that will take this route.Speciﬁes the next hop to be taken if this route is used.Enable:Interface:Destination:Subnet Mask:Gateway:RoutingThis option allows you to deﬁne ﬁxed routes to deﬁned destinations.

42D-Link DIR-615 User ManualSection 3 - ConﬁgurationEnter a new Login Name for the Administrator account.Enter a new password for the Administrator Login Name and then retype the new password in the Conﬁrm Password textbox. The administrator can make changes to the settings.Remote management allows the DIR-615 to be conﬁgured from the Internet by a web browser. A username and password is still required to access the Web-Management interface. In general, only a member of your network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host.The Internet IP address of the computer that has access to the Broadband Router. If you input an asterisk (*) into this ﬁeld, then any computer will be able to access the Router. Putting an asterisk (*) into this ﬁeld would present a security risk and is not recommended.The port number used to access the DIR-615. For example: http://x.x.x.x:8080 whereas x.x.x.x is the WAN IP address of the DIR-615 and 8080 is the port used for the Web-Management interface.Administrator Login Name:Administrator Password:Enable Remote Management:IP Allowed to Access:Port:Device AdministrationThis window will allow you to change the Administrator password. You can also enable Remote Management.

43D-Link DIR-615 User ManualSection 3 - ConﬁgurationSave and RestoreUse this option to save the current router conﬁguration settings to a ﬁle on the hard disk of the computer you are using. First, click the Save button. You will then see a ﬁle dialog, where you can select a location and ﬁle name for the settings. Use this option to load previously saved router configuration settings. First, use the Browsecontrol to ﬁnd a previously save ﬁle of conﬁguration settings. Then, click the Upload Settings button to transfer those settings to the Router. This option will restore all conﬁguration settings back to the settings that were in effect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router conﬁguration settings, use the Savebutton above. Click the Reboots button on the left side of the window to restart the Router.Save Settings to Local Hard Drive:Load Settings from Local Hard Drive:Restore to Factory Default Settings:Reboots:This window allows you to save your conﬁguration ﬁle to a hard drive, load conﬁguration settings from a hard drive, and restore the Router’s factory default settings.

44D-Link DIR-615 User ManualSection 3 - ConﬁgurationFirmware UpdateClick the Check Now button (or the link at the top of the window) to ﬁnd out if there is an updated ﬁrmware; if so, download the new ﬁrmware to your hard drive.After you have downloaded the new ﬁrmware, click Browse in this window to locate the ﬁrmware update on your hard drive. Click Save Settings to complete the ﬁrmware upgrade.Firmware Upgrade:Browse:You can upgrade the ﬁrmware of the Router here. Make sure the ﬁrmware you want to use is on the local hard drive of the computer. Click on Browse to locate the ﬁrmware ﬁle to be used for the update. Please check the D-Link support site for ﬁrmware updates at http://support.dlink.com. You can download ﬁrmware upgrades to your hard drive from the D-Link support site.

45D-Link DIR-615 User ManualSection 3 - ConﬁgurationDDNS SettingTick the Enable DDNS checkbox to enable support for DDNS.Select one of the DDNS registration organizations form those listed in the pull-down menu. Available servers include dlinkddns.com(Free), DynDns.org(Custom), Dyn.Dns.org(free), and Dyn.Dns.org(Static).Enter the host name of the DDNS server.Enter the username given to you by your DDNS server.Enter the password or key given to you by your DDNS server.Enable DDNS:Server Address:Host Name:Username:Password:The router supports DDNS (Dynamic Domain Name Service). The Dynamic DNS service allows a dynamic public IP address to be associated with a static host name in any of the many domains, allowing access to a speciﬁed host from various locations on the Internet. This is enabled to allow remote access to a host by clicking a hyperlinked URL in the form “hostname.dyndns.org”. Many ISPs assign public IP addresses using DHCP, this can make it difﬁcult to locate a speciﬁc host on the LAN using standard DNS. If for example you are running a public web server or VPN server on your LAN, this ensures that the host can be located from the Internet if the public IP address changes. DDNS requires that an account be setup with one of the supported DDNS providers.

46D-Link DIR-615 User ManualSection 3 - ConﬁgurationSystem CheckVCT is an advanced feature that integrates a LAN cable tester on every Ethernet port on the router. Through the graphical user interface (GUI), VCT can be used to remotely diagnose and report cable faults such as opens, shorts, swaps, and impedance mismatch. This feature signiﬁcantly reduces service calls and returns by allowing users to easily troubleshoot their cable connections.The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping.Virtual Cable Tester (VCT) Info:Ping Test:This tool is used to verify the physical connectivity on both the LAN and the WAN interfaces. The Ping Test can be used to test the status of the Internet.

47D-Link DIR-615 User ManualSection 3 - ConﬁgurationSchedulesEnter a name for the new schedule rule.Choose the desired day(s), either All Week or Select Days. If the latter is selected, please use the checkboxes directly below to specify the individual days.Tick this check box if the new schedule rule applies to the full 24-hour period.If the new schedule rule does not apply to the full 24-hour period, untick the previous checkbox and then enter a speciﬁc beginning and ending time. Name:Day(s):All Day - 24 hrs:Start Time/End Time:The Router allows the user the ability to manage schedule rules for various ﬁrewall and parental control features on this window. Once you have ﬁnished conﬁguring the new schedule rule, click the Save Settings button at the top of the window.

48D-Link DIR-615 User ManualSection 3 - ConﬁgurationLog SettingsClick on the Save button link on this window to save the log ﬁle to your local hard drive.click the checkbox to save the log in the log server in the LAN side.Click the checkbox(es) of the type of log information requested: “System, Firewall & Security, Router Status, Critical, Warning and Information”Enter the your SNTP server name(or IP address) and enter your mail address before sending your system log by mail.Save Log File:Syslog Server:Log Type & Level:Send by Mail:The system log displays chronological event log data speciﬁed by the router user. You may also save a simple text ﬁle containing the log to your computer. Click the Save button and follow the prompts to save the ﬁle.

49D-Link DIR-615 User ManualSection 3 - ConﬁgurationDevice InfoThis window displays the current information for the DIR-615. It will display the LAN, WAN, and Wireless information.If your WAN connection is set up for a Dynamic IP address then a DHCP Release button and a DHCP Renew button will be displayed. Use DHCP Release to disconnect from your ISP and use DHCP Renew to connect to your ISP. If your WAN connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.Displays the MAC address and the private (local) IP settings for the router.Displays the MAC address and the public IP settings for the router.Displays the wireless MAC address and your wireless settings such as SSID, Channel, and Encryption status.LAN:WAN:Wireless 802.11N:

50D-Link DIR-615 User ManualSection 3 - ConﬁgurationLogFirst Page:Last Page:Previous:Next:Clear:Link to Log Settings:View the ﬁrst page of the log.View the last page of the log.View the previous page.View the next page.Clear the log.Click this button to go directly to the Log Settings window (Maintenance > Log Settings).This window allows you to view a log of activities on the Router. This is especially helpful detecting unauthorized network usage.

51D-Link DIR-615 User ManualSection 3 - ConﬁgurationStatisticsActive Session The window below displays the Trafﬁc Statistics. Here you can view the amount of packets that pass through the DIR-615 on both the WAN and the LAN ports. The trafﬁc counter will reset if the device is rebooted.The NAPT Active Session table displays a list of all active conversations between WAN computers and LAN computers.

52D-Link DIR-615 User ManualSection 3 - ConﬁgurationWirelessThe wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless client.

53D-Link DIR-615 User ManualSection 3 - ConﬁgurationHelpClick the desired hyperlink to get more information about how to use the Router.

54D-Link DIR-615 User ManualSection 4 - SecurityWireless SecurityThis section will show you the different levels of security you can use to protect your data from intruders. The DIR-615 offers the following types of security:• WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key)• WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)• WEP (Wired Equivalent Privacy)What is WEP?WEP stands for Wired Equivalent Privacy. It is based on the IEEE 802.11 standard and uses the RC4 encryption algorithm. WEP provides security by encrypting data over your wireless network so that it is protected as it is transmitted from one wireless device to another.To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit encryption. Keys are deﬁned by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange – alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to HEX for use over the network. Four keys can be deﬁned so that you can change keys easily.

55D-Link DIR-615 User ManualSection 4 - SecurityConﬁgure WEPIt is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based conﬁguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Setup on the left side.2. Next to Security Mode, select Enable WEP Wireless Security (basic).3. Next to Authentication, select either Shared Key or Open.Shared Key is recommended as it provides greater security when WEP is enabled.4. Select either 64Bit or 128Bit encryption from the drop-down menu next to WEP Encryption.5. Next to Default Key Type, select WEP Key 1 and enter a WEP key that you create. Make sure you enter this key exactly on all your wireless devices. You may enter up to four different keys either using Hex or ASCII.Hex is recommended (letters A-F and numbers 0-9 are valid). In ASCII all numbers and letters are valid.6. Click Save Settings to save your settings. If you are conﬁguring the router with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the router.

56D-Link DIR-615 User ManualSection 4 - SecurityWhat is WPA?WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).The two major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer’s hardware-speciﬁc MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network.WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point.WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network.

57D-Link DIR-615 User ManualSection 4 - SecurityConﬁgure WPA-PSK and WPA2-PSKIt is recommended to enable encryption on your wireless Router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based conﬁguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click onWireless Setup on the left side.2. Next to Security Mode, select Enable WPA Only Wireless Security (enhanced) or Enable WPA2 Only Wireless Security (enhanced).3. Next to Cipher Mode, select TKIP,AES,or Both.4. Next to PSK/EAP, select PSK.5. Next to Network Key, enter a key (passphrase). The key is an alpha-numeric passwordbetween 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. Make sure you enter this key exactly the same on all other wireless clients.6. Click Save Settings to save your settings. If you are conﬁguring the Router with a wireless adapter, you will lose connectivity until you enable WPA-PSK or WPA2-PSK on your adapter and enter the same passphrase as you did on the Router.

58D-Link DIR-615 User ManualSection 4 - SecurityConﬁgure WPA/WPA2-PSKIt is recommended to enable encryption on your wireless Router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based conﬁguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click onWireless Setup on the left side.2. Next to Security Mode, select Enable WPA/WPA2 Wireless Security (enhanced).3. Next to Cipher Mode, select TKIP,AES,or Both.4. Next to PSK/EAP, select PSK.5. Next to Network Key, enter a key (passphrase). The key is an alpha-numeric passwordbetween 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. Make sure you enter this key exactly the same on all other wireless clients.6. Click Save Settings to save your settings. If you are conﬁguring the Router with a wireless adapter, you will lose connectivity until you enable WPA/WPA2-PSK on your adapter and enter the same passphrase as you did on the Router.

59D-Link DIR-615 User ManualSection 4 - SecurityConﬁgure WPA, WPA2, and WPA/WPA2 (RADIUS)It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based conﬁguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Settings on the left side.2. Next to Security Mode, select Enable WPA Only Wireless Security (enhanced), Enable WPA2 Only Wireless Security (enhanced), or Enable WPA/WPA2 Wireless Security (enhanced).3. Next to Cipher Type, select TKIP, AES,or Auto.4. Next to PSK/EAP, select EAP.5. Next to RADIUS Server 1 enter the IP Address of your RADIUS server.6. Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port.7. Next to Shared Secret, enter the security key.8. If you have a secondary RADIUS server, enter its IP address, port, and secret key.9. Click Save Settings to save your settings.

60D-Link DIR-615 User ManualSection 5 - Connecting to a Wireless NetworkConnect to a Wireless NetworkUsing Windows® XPWindows® XP users may use the built-in wireless utility (Zero Conﬁguration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks.If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. orThe utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

61D-Link DIR-615 User ManualSection 5 - Connecting to a Wireless NetworkConﬁgure WEPIt is recommended to enable WEP on your wireless router or access point before conﬁguring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used.2. Highlight the wireless network (SSID) you would like to connect to and click Connect.1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks.

62D-Link DIR-615 User ManualSection 5 - Connecting to a Wireless Network3. The Wireless Network Connection box will appear. Enter the same WEP key that is on your router and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WEP settings are correct. The WEP key must be exactly the same as on the wireless router.

63D-Link DIR-615 User ManualSection 5 - Connecting to a Wireless NetworkConﬁgure WPA-PSKIt is recommended to enable WEP on your wireless router or access point before conﬁguring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used.2. Highlight the wireless network (SSID) you would like to connect to and click Connect.1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks.

64D-Link DIR-615 User ManualSection 5 - Connecting to a Wireless Network3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.

65D-Link DIR-615 User ManualSection 6 - Setting Up Wi-Fi Protection (WCN 2.0 in Windows Vista)Setting Up Wi-Fi Protection(WCN 2.0 in Windows Vista)The DIR-615 supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista. The instructions for setting this up depend on whether you are using Windows Vista to conﬁgure the Router or third party software. Initial Router Conﬁguration for Wi-Fi ProtectionWhen you ﬁrst set up the Router, Wi-Fi protection is disabled and unconﬁgured. To enjoy the beneﬁts of Wi-Fi protection, the Router must be both enabled and conﬁgured. There are three basic methods to accomplish this: use Windows Vista’s built-in support for WCN 2.0, use software provided by a third party, or use the traditional Ethernet approach. If you are running Windows Vista, tick the Enable checkbox on the Wireless Network window. Use the Current PIN that is displayed on the Wireless Network window or choose to click the Generate New PIN button or Reset PIN to Default button. If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are ﬁnished, proceed to the next section to set up the newly-conﬁgured Router.

66D-Link DIR-615 User ManualSection 6 - Setting Up Wi-Fi Protection (WCN 2.0 in Windows Vista)Setting Up a Conﬁgured RouterOnce the Router has been conﬁgured, you can use the push button on the Router or third party software to invite a newcomer to join your Wi-Fi protected network. For maximum security, the software method is recommended. However, the push button method is ideal if there is no access to a GUI.If you are using the Router’s Wi-Fi Security push button option, simultaneously depress the push button located on the side of the Router and the button on the client (or virtual button on the client’s GUI). Next click Finish. The Client’s software will then allow a newcomer to join your secure, Wi-Fi protected network.If you are using third party software, run the appropriate Wi-Fi Protected System utility. You will be asked to either use the push button method or to manually enter the PIN. Follow the on-screen instructions.

67D-Link DIR-615 User ManualSection 7 - Changing the Computer Name and Joining a WorkgroupChanging the Computer Name and Joining a WorkgroupThe following are step-by-step directions to change the computer name and join a workgroup.2. Click on the Advanced system settings link. 1. Click on Properties.

68D-Link DIR-615 User ManualSection 7 - Changing the Computer Name and Joining a Workgroup3. Click the Computer Name tab in the System Properties windowand enter a description of your computer in the textbox. When you are ﬁnished, click the Change button. 4. Go to the Computer Name/Domain Changes window and click the radio button next to the Workgroup you want to join. When you are ﬁnished, click the OK button.

69D-Link DIR-615 User ManualSection 8 - Conﬁguring the IP Address in VistaConﬁguring the IP Address in VistaThe following are step-by-step directions to conﬁgure the IP address in Windows Vista.2. Go to the Network and Internet window and click the appropriate Local Area Connection icon. 1. Click on Properties. 3. Right-click the Local Area Connection icon and then select Properties from the drop-down menu.

70D-Link DIR-615 User ManualSection 8 - Conﬁguring the IP Address in Vista4. Tick the Internet Protocol Version 4 (TCP/IPv4) checkbox in the Networking tab in the Local Area Connection Propertieswindow.5. Click the “Use the following IP address” option in the Generaltab in the Local Area Connections Properties window and enter the desired IP address in the space offered. Then click the “Use the following DNS server adresses” option on the same tab and enter the desired DNS server information.

71D-Link DIR-615 User ManualSection 8 - Conﬁguring the IP Address in Vista6. Right-click the Local Area Connection icon and then select Statusfrom the drop-down menu. 7. Go to the Local Area Connection Status window and click the Details button. 8. Conﬁrm your new settings on the Network Connection Status window. When you are ﬁnished, click the Done button.

72D-Link DIR-615 User ManualSection 9 - Setting Up a Connection WirelesslySetting Up a Connection or Network WirelesslyThe following are step-by-step directions to set up a wireless connection.2. Go to the Set up a connection or network window and choose the Set up a wireless router or access point Set up a new wireless network for your home or business option. Click the Next button. 1. Click on Set up a connection or network in the Network and Sharing Center section.

73D-Link DIR-615 User ManualSection 9 - Setting Up a Connection Wirelessly3. Click the Next button on the Set up a wireless router or access point window. 4. The following window displays the system progress. 5. This window conﬁrms that you want to create wireless network settings that are savable to a USB ﬂash drive.

74D-Link DIR-615 User ManualSection 9 - Setting Up a Connection Wirelessly6. Enter a network name on the Give your network a name window in the Set up a wireless router or access point wizard. Click the Next button. 7. Enter a passphrase on the Help make your network more secure with a passphrase window in the Set up a wireless router or access point wizard. Click the Show advanced network security options link. 8. Select security method on the Choose advanced network security options window in the Set up a wireless router or access pointwizard. Click the Next button.

75D-Link DIR-615 User ManualSection 9 - Setting Up a Connection Wirelessly9. Once you have selected the desired security method on the Choose advanced network security options window in the Set up a wireless router or access point wizard, click the Next button.10.Select the desired ﬁle and printer sharing option on the Chooseﬁle and printer sharing options window in the Set up a wireless router or access point wizard. Click the Next button.11.Once you have saved your network settings to USB, use the pull-down menu on the Insert the USB ﬂash drive into this computer window in the Set up a wireless router or access point wizard to select a destination for your network settings. Click the Next button.

76D-Link DIR-615 User ManualSection 9 - Setting Up a Connection Wirelessly12.Once you have saved your network settings to USB, the Copying settings to the USB drive window in the Set up a wireless router or access point wizard opens to indicate the system progress. 13.Once you are ﬁnished, the To add a device or computer, follow these instructions window in the Set up a wireless router or access point wizard opens. When you are ﬁnished, click the Closebutton.

77D-Link DIR-615 User ManualSection 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK)Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK)The following are step-by-step directions to set up a wireless connection.2. Click the Manage network connections link in the Network and Sharing Center window. 1. Click on Properties.

78D-Link DIR-615 User ManualSection 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK)4. Select a network to connect to in the Select a network to connectto window in the Connect to a network wizard and then click the Connect button. 5. The following Connect to a network wizard window displays the system progress. 3. Right-click the Wireless Network Connection entry and then select Connect/Disconnect from the drop-down menu.

79D-Link DIR-615 User ManualSection 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK)7. The following Successfully connected to dlink300 window in the Connect to a network wizard is displayed. Choose to save to the network and/or start the new connection automatically. When you are ﬁnished, click the Close button. 8. The successful connection is displayed at the bottom of the Windows start up menu. 6. Enter the network security key or passphrase for the Router in the textbox provided in the Type the network security key or passphrase for dlink300 window in the Connect a network wizard. When you are ﬁnished, click the Connect button.

80D-Link DIR-615 User ManualSection 10 - Connecting to a Secured Wireless Network (WEP, WPA-PSK & WPA2-PSK)10.To test the new IP address, use the Ping feature of the command prompt.9. Conﬁrm your new settings by calling up the command prompt and then entering the ipconﬁg command.

81D-Link DIR-615 User ManualSection 11 - Connecting to an Unsecured Wireless NetworkConnecting to an Unsecured Wireless NetworkThe following are step-by-step directions to set up an unsecured wireless connection.2. Go to the Network and Sharing Center window and click the Manage Network Connections link. 1. Click on Properties.

82D-Link DIR-615 User ManualSection 11 - Connecting to an Unsecured Wireless Network3. Right-click the Wireless Network Connection entry and then select Connect/Disconnect from the drop-down menu. 4. Select a network to connect to in the Select a network to connectto window in the Connect to a network wizard and then click the Connect button. 5. Conﬁrm your desire to connect anyway on the following Network Connection Status window.

83D-Link DIR-615 User ManualSection 11 - Connecting to an Unsecured Wireless Network6. The following Connect to a network wizard window displays the system progress. 7. The following Successfully connected to dlink300 window in the Connect to a network wizard is displayed. Choose to save to the network and/or start the new connection automatically. When you are ﬁnished, click the Close button. 8. The successful connection is displayed at the bottom of the Windows start up menu.

84D-Link DIR-615 User ManualSection 11 - Connecting to an Unsecured Wireless Network9. Conﬁrm your new settings by calling up the command prompt and then entering the ipconﬁg command. 10.To test the new IP address, use the Ping feature of the command prompt.

85D-Link DIR-615 User ManualSection 12 - TroubleshootingTroubleshootingThis chapter provides solutions to problems that can occur during the installation and operation of the DIR-615. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.)1. Why can’t I access the web-based conﬁguration utility?When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. • Make sure you have an updated Java-enabled web browser. We recommend the following: • Internet Explorer 6.0 or higher • Netscape 8 or higher • Mozilla 1.7.12 (5.0) or higher • Opera 8.5 or higher • Safari 1.2 or higher (with Java 1.3.1 or higher) • Camino 0.8.4 or higher • Firefox 1.5 or higher • Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.• Disable any internet security software running on the computer. Software ﬁrewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows® XP ﬁrewall may block access to the conﬁguration pages. Check the help ﬁles included with your ﬁrewall software for more information on disabling or conﬁguring it.

86D-Link DIR-615 User ManualSection 12 - Troubleshooting• Conﬁgure your Internet settings:• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults.• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settingsbutton. Make sure nothing is checked. Click OK.• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.• Close your web browser (if open) and open it.• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your the web management. • If you still cannot access the conﬁguration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the conﬁguration. If you have multiple computers, try connecting using a different computer.2. What can I do if I forgot my password?If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.

87D-Link DIR-615 User ManualSection 12 - Troubleshooting3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To ﬁnd the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL. • Click on Start and then click Run.• Windows® 95, 98, and Me users type in command (Windows® NT, 2000, and XP users type in cmd) and press Enter (or click OK).• Once the window opens, you’ll need to do a special ping. Use the following syntax: ping [url] [-f] [-l] [MTU value]Example: ping yahoo.com -f -l 1472

88D-Link DIR-615 User ManualSection 12 - TroubleshootingYou should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you ﬁnd your MTU, you can now conﬁgure your router with the proper MTU size. To change the MTU rate on your router follow the steps below: • Open your browser, enter the IP address of your router (192.168.0.1) and click OK.• Enter your username (admin) and password (blank by default). Click OK to enter the web conﬁguration page for the device. • Click on Setup and then click Manual Conﬁgure.• To change the MTU enter the number in the MTU ﬁeld and click the Save Settings button to save your settings.• Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten.

89D-Link DIR-615 User ManualAppendix A - Wireless BasicsD-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and ofﬁce environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efﬁciently. Increased mobility and the absence of cabling and other ﬁxed infrastructure have proven to be beneﬁcial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link.Wireless Basics

90D-Link DIR-615 User ManualAppendix A - Wireless BasicsWhat is Wireless?Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or ofﬁce network.Why D-Link Wireless?D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.How does wireless work?Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN).Wireless Local Area Network (WLAN)In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.

91D-Link DIR-615 User ManualAppendix A - Wireless BasicsWireless Personal Area Network (WPAN)Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away.Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, ofﬁce, business, D-Link has a wireless solution for it.Home • Gives everyone at home broadband access • Surf the web, check email, instant message, and etc • Gets rid of the cables around the house • Simple and easy to useSmall Ofﬁce and Home Ofﬁce • Stay on top of everything at home as you would at ofﬁce • Remotely access your ofﬁce network from home • Share Internet connection and printer with multiple computers • No need to dedicate ofﬁce space

92D-Link DIR-615 User ManualAppendix A - Wireless BasicsWhere is wireless used? Wireless technology is expanding everywhere not just at home or ofﬁce. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like airports, hotels, coffee shops, libraries, restaurants, and convention centers.Wireless network is easy to setup, but if you’re installing it for the ﬁrst time it could be quite a task not knowing where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.TipsHere are a few things to keep in mind, when you install a wireless network.Centralize your router or Access PointMake sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range.For the wireless repeater, there are two types of repeater in D-Link for user to select: Universal repeater: It acts as an AP and a wireless STA at the same time. It can support all AP and wireless STA if they work in the same wireless channel. AP-repeater (AP with WDS): only repeat same model or limited models which base on the same proprietary protocol.Please choose a universal repeater to boost the signal to extend the range.

93D-Link DIR-615 User ManualAppendix A - Wireless BasicsEliminate InterferencePlace home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would signiﬁcantly reduce any interference that the appliances might cause since they operate on same frequency.SecurityDon’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more WNA-2330 wireless network Cardbus adapters.An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate.Wireless Modes

94D-Link DIR-615 User ManualAppendix B - Networking BasicsNetworking BasicsCheck your IP addressAfter you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.Click on Start > Run. In the run box type cmd and click OK.At the prompt, type ipconﬁg and press Enter.This will display the IP address, subnet mask, and the default gateway of your adapter.If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some ﬁrewall software programs may block a DHCP request on newly installed adapters.If you are connecting to a wireless network at a hotspot (e.g. hotel, coffee shop, airport), please contact an employee or administrator to verify their wireless network settings.

95D-Link DIR-615 User ManualAppendix B - Networking BasicsStatically Assign an IP addressIf you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:Step 1Windows® XP - Click on Start > Control Panel > Network Connections.Windows® 2000 - From the desktop, right-click My Network Places > Properties.Step 2Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.Step 3Highlight Internet Protocol (TCP/IP) and click Properties.Step 4Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.Step 5Click OK twice to save your settings.

96D-Link DIR-615 User ManualAppendix C - Technical SpeciﬁcationsTechnical SpeciﬁcationsStandards • IEEE 802.11g • IEEE 802.11b • IEEE 802.11n • IEEE 802.3 • IEEE 802.3u • IEEE 802.3xWireless Signal Rates* • 300Mbps • 54Mbps • 48Mbps • 36Mbps • 24Mbps • 18Mbps • 12Mbps • 11Mbps • 9Mbps • 6Mbps • 5.5Mbps • 2Mbps • 1MbpsSecurity • WPA - Wi-Fi Protected Access (TKIP, MIC, IV Expansion, Shared Key Authentication) • 802.1x • 64/128-bit WEPModulation Technology802.11 b : DSSS / DBPSK / DQPSK / CCK802.11 g : 16QAM / 64QAM / BPSK / QPSK with OFDM 802.11 n : 16QAM / 64QAM / BPSK / QPSK with OFDMReceiver Sensitivity802.11nHT20• 300Mbps OFDM, 10% PER, –68dBmHT40• 300Mbps OFDM, 10% PER, –64dBm802.11b and 802.11g• 54Mbps OFDM, 10% PER,-70dBm• 48Mbps OFDM, 10% PER,-72dBm• 36Mbps OFDM, 10% PER,-76dBm• 24Mbps OFDM, 10% PER,-78dBm• 18Mbps OFDM, 10% PER,-80dBm• 12Mbps OFDM, 10% PER,-83dBm• 11Mbps CCK, 8% PER,-85dBm• 9Mbps OFDM, 10% PER,-85dBm• 6Mbps OFDM, 10% PER,-88dBm• 5.5Mbps CCK, 8% PER,-87dBm• 2Mbps DQPSK, 8% PER,-89dBm• 1Mbps DBPSK, 8% PER,-90dBmVPN Pass Through/ Multi-Sessions • PPTP • IPSecDevice Management • Web-based Internet Explorer v6 or later; Netscape Navigator v6 or later; or other Java-enabled browsers • DHCP Server and Client

97D-Link DIR-615 User ManualAppendix C - Technical SpeciﬁcationsWireless Frequency Range2.4GHz to 2.497GHz (802.11b)2.4GHz to 2.4835GHZ (802.11g and 802.11n)Wireless Operating Range2 • Indoors - up to 328 ft. (100 meters) • Outdoors- up to 1312 ft. (400 meters)Wireless Transmit Power (AVG Power)11b:17dBm(Max) 11g:16dBm(Max) 11n:13dBm(Max)External Antenna TypeTwo ﬁxed reverse SMA external antennaAdvanced Firewall Features • NAT with VPN Pass-through (Network Address Translation) • MAC Filtering • IP Filtering • URL Filtering • Domain Blocking • SchedulingOperating Temperature32°F to 129 °F ( 0°C to 40°C)Humidity95% maximum (non-condensing)* Maximum wireless signal rate derived from IEEE Standard 802.11b, 802.11g and 802.11n speciﬁcations. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trafﬁc, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range.Safety and EmissionsFCC Part 15B/ 15C/ MPEIC RSS-210NCC LP0002LEDs • Power • Status • Internet • WLAN (Wireless Connection) • LAN (10/100)Dimensions• L = 135mm• W = 99.8mm• H = 31.5mmWeight0.246kgWarranty1 Year35113594/6NI{!Two fixed I-PEX MHF external antenna

98D-Link DIR-615 User ManualAppendix E - WarrantyWarrantySubject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the ﬁfty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.Limited Warranty:D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except as otherwise stated herein. • Hardware (excluding power supplies and fans): One (1) year • Power supplies and fans: One (1) year • Spare parts and spare kits: Ninety (90) daysThe customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Ofﬁce. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.

99D-Link DIR-615 User ManualAppendix E - WarrantyLimited Software Warranty:D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional speciﬁcations for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional speciﬁcations for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed by DLink in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is ﬁrst returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.Non-Applicability of Warranty:The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufﬁcient detail to allow DLink to conﬁrm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.com/.

100D-Link DIR-615 User ManualAppendix E - Warranty• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product and will not ship back any accessories.• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.What Is Not Covered:The Limited Warranty provided herein by D-Link does not cover:Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modiﬁcation, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, ﬁrmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service Ofﬁce. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.Disclaimer of Other Warranties:EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.

101D-Link DIR-615 User ManualAppendix E - WarrantyIF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.Limitation of Liability:TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY.Governing Law:This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This Limited Warranty provides speciﬁc legal rights and you may also have other rights which vary from state to state.Trademarks:D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners.Copyright Statement:No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.Copyright ©2005-2007 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.

102D-Link DIR-615 User ManualAppendix E - WarrantyCE Mark Warning:This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.FCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link ofﬁce.Industry Canada StatementOperation is subject to the following two conditions:1) this device may not cause interference and2) this device must accept any interference, including interference that may cause undesired operation of the deviceThis device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antennaimpedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.CSA Statement:The Router must be used with the power adapter included with the device.Caution - To reduce the risk of ﬁre, use only No. 26 AWG or larger telecommunication line cord.Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. אՀᤞ፿ᔞش؀᨜چ೴Κʳ ᆖীڤᎁᢞٽ௑հ܅פ෷୴᙮ሽᖲΔॺᆖ๺ױΔֆ׹Ε೸ᇆࢨࠌشृ݁լ൓ᖐ۞᧢ޓ᙮෷ΕףՕפ෷ࢨ᧢ޓ଺๻ૠհ௽ࢤ֗פ౨Ζʳ ܅פ෷୴᙮ሽᖲհࠌشլ൓ᐙ᥼ଆ౰ڜ٤֗եឫٽऄຏॾΙᆖ࿇෼ڶեឫ෼ွழΔᚨمܛೖشΔࠀޏ࿳۟ྤեឫழֱ൓ᤉᥛࠌشΖছႈٽऄຏॾΔਐࠉሽॾऄ๵ࡳ܂ᄐհྤᒵሽຏॾΖ܅פ෷୴᙮ሽᖲႊݴ࠹ٽऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭شሽंᘿ୴ࢤሽᖲ๻ໂհեឫΖʳ

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2024 UserManual.wiki | Privacy Policy

Contact Us
DMCA