D Link DWL700AP-A2 D-Link Air 2.4GHz Wireless Access Point User Manual dwl900AP manual 224

D Link Corporation D-Link Air 2.4GHz Wireless Access Point dwl900AP manual 224

User Manual Part 9

Networking Basics (continued) Assigning a Static IP Address • Double-click on Network Connections • Right-click on Local Area Connections. • Double-click Properties 46
Networking Basics (continued) Assigning a Static IP Address • Click OK You have completed the assignment of a Static IP Address. (You do not need to assign a Static IP Address if you have a DHCP-capable Gateway/Router.) • Click on Internet Protocol (TCP/IP) • Click Properties • Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window, • Input your IP address and subnet mask. (The IP Addresses on your networkmust be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computers should have IP Addresses that are sequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must be the same for all the computers on the network.) • Input your DNS server addresses. (Note: If you are entering a DNS server, you must enter the IP Address of the Default Gateway.) The DNS server information will be provided by your ISP (Internet Service Provider.) DWL-650+ Wireless Cardbus Adapter 192 168 0 1 192 168 0 1 47
Networking Basics (continued) Assigning a Static IP Address with Macintosh OS X Go to the Apple Menu and select System Preferences. Click on Network Select Built-in Ethernet in the Show pull-down menu. Select Manually in the Configure pull-down menu. Input the Static IP Address, the Subnet Mask and the Router IP Address in the appropriate fields. Click Apply Now 48
Networking Basics (continued) Selecting a Dynamic IP Address with Macintosh OS X Go to the Apple Menu and select System Preferences. Click on Network Select Built-in Ethernet inthe Show pull-down menu. Select Using DHCP in theConfigure pull-down menu. Click Apply Now The IP Address, Subnet mask, and the Router’s IP Address will appear in a few seconds. 49
Networking Basics (continued) Checking the Wireless Connection by Pinging For Windows XP and 2000: Go to Start > Run > type cmd. A window similar to Fig. 9.25 will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP address of the Wireless Router or Access Point. A good wireless connection will show four replies from the wireless router or access point, as shown. For Windows Me and 98: Go to Start > Run > type command. A window similar to Fig. 9.26 will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP address of the Wireless Router or Access Point. A good wireless connection will show four replies from the wireless router or access point, as shown. Adding and Sharing Printers in Windows XP After you have run the Network Setup Wizard on all the computers in your network (please see the Network Setup Wizard section at the beginning of Networking Basics,) you can use the Add Printer Wizard to add or share a printer on your network. Whether you want to add a local printer (a printer connected directly to one computer,) share an LPR printer (a printer connected to a print server) or share a network printer (a printer connected to your network through a Gateway/Router,) use the Add Printer Wizard. Please follow the directions below: Fig. 8.35Fig. 8.36 50
Networking Basics (continued) Adding a local printer (A printer connected directly to a computer) A printer that is not shared on the network and is connected directly to one computer is called a local printer. If you do not need to share your printer on a network, follow these directions to add the printer to one computer. • Go to Start> Printers and Faxes • Click on Add a printer 51
Networking Basics (continued) Adding a local printer • Click Next • Select Local printer attached to this computer • (Deselect Automatically detect and install my Plug and Play printer if it has been selected.) • Click Next • Select Use the following port: • From the pull-down menu select the correct port for your printer (Most computers use the LPT1: port, as shown in the illustration.) • Click Next 52
Networking Basics (continued) Adding a local printer • Select and highlight the correct driver for your printer. • Click Next (If the correct driver is not displayed, insert the CD or floppy disk that came with your printer and click Have Disk.) • At this screen, you can change the name of the printer (optional.) • Click Next • Select Yes, to print a test page. A successful printing will confirm that you have chosen the correct driver. • Click Next 53
Networking Basics (continued) Adding a local printer Click Finish Click OK This screen gives you information about your printer.When the test page has printed, 54
Networking Basics (continued) Adding a local printer Sharing a network printer After you have run the Network Setup Wizard on all the computers on your network, you can run the Add Printer Wizard on all the computers on your network. Please follow these directions to use the Add Printer Wizard to share a printer on your network: • Go to Start> Printers and Faxes A successful installation will display the printer icon as shown at right. You have successfully added a local printer. • Go to Start> Printers and Faxes 55
Networking Basics (continued) Sharing a network printer • Click on Add a Printer • Click Next • Select Network Printer • Click Next 56
Networking Basics (continued) Sharing a network printer • Select Browse for a printer • Click Next • Select the printer you would like to share. • Click Next • Click Finish 57
Networking Basics (continued) Sharing a network printer To check for proper installation: • Go to Start> Printers and Faxes The printer icon will appear at right, indicating proper installation. You have completed adding the printer. To share this printer on your network: • Remember the printer name • Run the Add Printer Wizard on all the computers on your network. • Make sure you have already run the Network Setup Wizard on all the network computers. After you run the Add Printer Wizard on all the computers in the network, you can share the printer. 58
Networking Basics (continued) Sharing an LPR printer To share an LPR printer (using a print server,) you will need a Print Server such as the DP-101P+. Please make sure that you have run the Network Setup Wizard on all the computers on your network. To share an LPR printer, please follow these directions: • Go to Start> Printers and Faxes • Click on Add a Printer The screen to the right will display. • Click Next • Select Local printer… • Click Next 59
Networking Basics (continued) Sharing an LPR printer • Select Create a new port • From the pull-down menu, select Standard TCP/IP Port, as shown. • Click Next • Please read the instructionson this screen. • Click Next • Enter the Printer IP Address and the Port Name, as shown. • Click Next 60
Networking Basics (continued) Sharing an LPR printer • In this screen,select Custom. • Click Settings • Enter the Port Name and the Printer Name or IP Address. • Select LPR • Enter a Queue Name (if your Print-Server/ Gateway has more than one port, you will need a Queue name.) • Click OK 61
Networking Basics (continued) Sharing an LPR printer • This screen will show you information about your printer. • Click Finish • Select the printer you are adding from the list of Printers. • Insert the printer driver disk that came with your printer. • Click Have Disk If the printer driver is already installed, • Select Keep existing driver • Click Next 62
Networking Basics (continued) Sharing an LPR printer • You can rename your printer if you choose. It is optional. Please remember the name of your printer. You will need this information when you use the Add Printer Wizard on the other computers on your network. • Click Next • Select Yes, to print a test page. • Click Next This screen will display information about your printer. • Click Finish to complete the addition of the printer. • Please run the Add Printer Wizard on all the computers on your network in order to share the printer. Note: You must run the Network Setup Wizard on all the computers on your network before you run the Add Printer Wizard. 63
Networking Basics (continued) Other Tasks For help with other tasks in home or small office networking, see Using the Shared Documents folder and Sharing files and folders in the Help and Support Center in Microsoft Windows XP. 9. Technical Specifications Standards IEEE 802.11b IEEE 802.3 IEEE 802.3u IEEE 802.1x ) 64Ports (1) 10/100Base-T Ethernet, RJ-45 (UTP) (1) Power – 5V DC, 2.0A Network Management Web-Based browser with JavaScript Frequency Range 2.4 – 2.4835 GHz, Direct Sequence Spread Spectrum (DSSS Data Rates (Mbps : Channel) 11 : CCK 5.5: CCK 2: Barker 1: Barker Data Security 64, 128-bit WEP (Wired Equivalent Privacy) Encryption Access Control List Diagnostic LED Power Link TX/RX
Antenna Type • Detachable Reverse SMA Range • Indoors – up to 328 feet (100 meters) • Outdoors – up to 1,312 feet (400 meters) Temperature • Operating: -10ºC to 55ºC (14ºF to 131ºF) • Storing: -20ºC to 65ºC (-4ºF to 149ºF) Humidity: • 5%-95%, non-condensing Emissions: • FCC part 15b • UL1950-3 65

Navigation menu