D Link DWLG630A1 802.11g Wireless Cardbus Adapter User Manual dwlG650 manual 104

D Link Corporation 802.11g Wireless Cardbus Adapter dwlG650 manual 104

Contents

User Manual

Manual802.11g (2.4GHz)DWL-G630 D-Link AirPlus GTMWireless Cardbus AdapterBuilding Networks for People
2ContentsPackage Contents ................................................................................3Introduction............................................................................................4Wireless Basics ....................................................................................5Installation Considerations ....................................................................7Getting Started ......................................................................................8Using the Configuration Utility ..............................................................11Networking Basics ..............................................................................18Troubleshooting...................................................................................31Technical Specifications ......................................................................36Contacting Technical Support ..............................................................38Warranty and Registration ...................................................................39
3Contents of Package:D-Link AirPlus G DWL-G630802.11g (2.4GHz) Wireless Cardbus AdapterManual, Warranty and Drivers on CDPrinted Quick Installation GuidePackage ContentsIf any of the above items are missing, please contact your reseller.System Requirements for Configuration:An 802.11g or 802.11b access point (for Infrastructure mode),or another 802.11g or 802.11b wireless adapter (for Ad-Hoc,Peer-to-Peer networking mode.)At least 32 MB of memory and a 300 MHz processorWindows XP/2000/Me/98SE A laptop or notebook computer with an available 32-bitcardbus slotTM
4FeaturesLEDsLED stands for Light-Emitting Diode. The DWL-G630 has the following LEDs:A blinking light indicatesdata is being transmitted.ActivityA steady light indicates aconnection to an accesspoint.LinkCompatible with 802.11b and 802.11g Devices - Fully compatible with the IEEE802.11b and 802.11g standards, the DWL-G630 can connect with existing 802.11b-or 802.11g- compliant routers, access points and cards. That means you can stillcommunicate with colleagues and friends while you have the ability to link to evenmore wireless networks.Faster Wireless Networking - Faster data transfers mean increased productivity.With the DWL-G630 in your laptop PC, you will have the flexibility of wireless net-working speeds that save you time and money.User-friendly configuration and diagnostic utilities.IntroductionThe D-Link AirPlus G DWL-G630 Wireless Cardbus Adapter is an 802.11b/802.11g(2.4GHz) wireless adapter that supports high-speed wireless networking at home, atwork or in public places.Unlike most network cards, the DWL-G630 provides data transfers at up to 54 Mbps(compared to the standard 11 Mbps) when used with other D-Link AirPlus G products.The 802.11g standard is backwards compatible with 802.11b products.32-bit Cardbus Performance/Plug & Play Connectivity - The DWL-G630 is apowerful 32-bit cardbus adapter that installs quickly and easily into laptop PCs, andwhen used with other D-Link Air Plus G products will automatically connect to thenetwork out of the box.TMTMTM
5Wireless BasicsWireless users can use the same applications they use on a wired network. Wirelessadapter cards used on laptop and desktop systems support the same protocols asEthernet adapter cards.D-Link wireless products are based on industry standards to provide easy-to-use andcompatible high-speed wireless connectivity within your home, business or public accesswireless networks. D-Link wireless products will allow you access to the data you want,when and where you want it. You will be able to enjoy the freedom that wireless networkingbrings.A wireless local area network (WLAN) is a computer network that transmits and receivesdata with radio signals instead of wires. WLANs are used increasingly in both home andoffice environments, and public areas such as airports, coffee shops and universities.Innovative ways to utilize WLAN technology are helping people to work and communicatemore efficiently. Increased mobility and the absence of cabling and other fixedinfrastructure have proven to be beneficial to many users.People use WLAN technology for many different purposes:Mobility - Productivity increases when people have access to data in any locationwithin the operating range of the WLAN. Management decisions based on real-timeinformation can significantly improve worker efficiency.Low Implementation Costs - WLANs are easy to set up, manage, change andrelocate. Networks that frequently change can benefit from WLANs ease ofimplementation. WLANs can operate in locations where installation of wiring may beimpractical.Installation and Network Expansion - Installing a WLAN system can be fast andeasy and can eliminate the need to pull cable through walls and ceilings. Wirelesstechnology allows the network to go where wires cannot go - even outside the home oroffice.Inexpensive Solution - Wireless network devices are as competitively priced asconventional Ethernet network devices.Scalability - WLANs can be configured in a variety of ways to meet the needs ofspecific applications and installations. Configurations are easily changed and rangefrom Peer-to-Peer networks suitable for a small number of users to larger Infrastructurenetworks to accommodate hundreds or thousands of users, depending on the numberof wireless devices deployed.
6D-Link AirPlus G DI-624Wireless RouterWireless Basics (continued)Standards-Based TechnologyThe DWL-G630 Wireless Cardbus Adapter utilizes the 802.11b and the 802.11g standards.The IEEE 802.11g standard is an extension of the 802.11b standard. It increases thedata rate up to 54 Mbps within the 2.4GHz band, utilizing OFDM technology.This means that in most environments, within the specified range of this device, you willbe able to transfer large files quickly or even watch a movie in MPEG format over yournetwork without noticeable delays. This technology works by transmitting high-speeddigital data over a radio wave utilizing OFDM (Orthogonal Frequency Division Multiplexing)technology. OFDM works by splitting the radio signal into multiple smaller sub-signalsthat are then transmitted simultaneously at different frequencies to the receiver. OFDMreduces the amount of crosstalk (interference) in signal transmissions. The D-Link DWL-G630 will automatically sense the best possible connection speed to ensure the greatestspeed and range possible.The DWL-G630 is backwards compatible with 802.11b devices. This means that if youhave an existing 802.11b network, the devices in that network will be compatible with802.11g devices at speeds up to 11Mbps in the 2.4GHz range.D-Link AirPlus G DWL-G520 and DWL-G510Wireless PCI cards used with desktop computersD-Link AirPlus G DWL-2000APEnhanced 2.4GHz Wireless Access PointTMTMTMThe DWL-G630 is also interoperable with other 802.11g and 802.11b standards-compliant devices.The DWL-G630 is compatible with the following wireless products:
7Wireless Basics (continued)Installation ConsiderationsThe D-Link AirPlus G DWL-G630 lets you access your network, using a wirelessconnection, from virtually anywhere within its operating range. Keep in mind, however,that the number, thickness and location of walls, ceilings, or other objects that thewireless signals must pass through, may limit the range. Typical ranges vary dependingon the types of materials and background RF (radio frequency) noise in your home orbusiness. The key to maximizing wireless range is to follow these basic guidelines:TMKeep your product away (at least 3-6 feet or 1-2 meters) from electrical devicesor appliances that generate RF noise.4Keep the number of walls and ceilings between the DWL-G630 and other networkdevices to a minimum - each wall or ceiling can reduce your DWL-G630’s rangefrom 3-90 feet (1-30 meters.) Position your devices so that the number of wallsor ceilings is minimized.1Be aware of the direct line between network devices. A wall that is 1.5 feet thick(.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. Ata 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so thatthe signal will travel straight through a wall or ceiling (instead of at an angle) forbetter reception.2Building materials can impede the wireless signal - a solid metal door or aluminumstuds may have a negative effect on range. Try to position wireless devices andcomputers with wireless adapters so that the signal passes through drywall oropen doorways and not other materials.3
8Getting StartedOn the following pages we will show you an example of an Infrastructure Network andan Ad-Hoc Network.An Infrastructure network contains an access point or a wireless router. TheInfrastructure Network example shown on the following page contains the followingD-Link network devices (your existing network may be comprised of other devices):A wireless router - D-Link AirPlus Xtreme G DI-624A laptop computer with a wireless adapter -D-Link AirPlus G DWL-G630A desktop computer with a wireless adapter -D-Link AirPlus G DWL-G520 or DWL-G510A cable modem - D-Link DCM-201There are basically two modes of networking:Ad-Hoc – directly connecting to another computer, for Peer-to-Peercommunication, using wireless network adapters on each computer,such as two or more DWL-G630 Wireless Cardbus Adapters.Infrastructure – using an access point, or wireless router, such asthe DI-624.TMTMTM
9Getting Started (continued)Setting up a Wireless Infrastructure NetworkFor a typical wirelesssetup at home (as shownabove), please do thefollowing:You will need broadband Internet access (a Cable or DSL-subscriber line intoyour home or office).Consult with your Cable or DSL provider for proper installation of the modem.Connect the Cable or DSL modem to your broadband router.(See the Quick Installation Guide included with your router).If you are connecting a desktop computer to your network, you can install theD-Link AirPlus G DWL-G520 or DWL-G510 Wireless PCI Adapter into anavailable PCI slot on your desktop computer.(See the Quick Installation Guide included with the network adapter).Install the D-Link DWL-G630 Wireless Cardbus Adapter into a laptop computer.(See the Quick Installation Guide included with the DWL-G630).If you wish, you may connect a computer that is equipped with an Ethernet net-work adapter (such as a DFE-530TX+) to the router also.TM111112222233333444445555566666DWL-G630with Laptop PCwith Laptop PCwith Laptop PCwith Laptop PCwith Laptop PCDWL-G520 or DWL-G510
10Getting Started (continued)Setting up a Wireless Ad-Hoc NetworkInstall the D-Link DWL-G630 Wireless Cardbus Adapter into one laptopcomputer. (See the Quick Installation Guide included with the product forinstallation instructions.)Install another DWL-G630 into a laptop computer.(See the Quick Installation Guide included with the product.)Set the wireless configuration for the adapters to Ad-Hoc mode, set theadapters to the same channel, and assign an IP address to each computeron the Ad-Hoc network. (See the box below).When assigning IP addresses to the computers on the network, please rememberthat the IP address for each computer must be in the same IP address rangeas all the computers in the network, and the subnet mask must be exactly thesame for all the computers in the network.For example: If the first computer is assigned an IP address of 192.168.0.2 with asubnet mask of 255.255.255.0, then the second computer can be assigned an IPaddress of 192.168.0.3 with a subnet mask of 255.255.255.0, etc.IMPORTANT: If computers or other devices are assigned the same IP address,one or more of the devices may not be visible on the network.IP AddressDWL-G630DWL-G630
11 Select the Wireless Networks tab.Uncheck the box in the properties windowthat enables windows configuration.D-Link AirPlusTM G DWL-G630 uses the Configuration Utility as the managementsoftware. The utility provides the user an easy interface to change any settings relatedto the wireless adapter. After you have completed the installation of the DWL-G630(refer to the Quick Installation Guide that came with your purchase) whenever youstart the computer, the Configuration Utility starts automatically and the system trayicon is loaded in the toolbar (see illustration below*.) Clicking on the utility icon will startthe Configuration Utility. Another way to start the Configuration Utility is to click onStart>Programs>D-Link AirPlus G >D-Link AirPlus G Utility.If you are using Windows XP, you can use either the Zero Configuration Utility or theD-Link Configuration Utility.If the icon does not display in the taskbar, then click onthis icon on your desktop to open.To use the D-Link Configuration Utility with XP, right-clickon the wireless network icon in the taskbar in the lowerright-hand corner of your computer screen.In the window that appears, select ViewAvailable Wireless Networks and clickthe Advanced button. The screen at rightwill appear.After you have done this, you can then use the D-LinkConfiguration Utility with XP by clicking on the D-LinkConfiguration Utility icon. *Configuration Utility iconin the system trayTMUsing the Configuration UtilityTM
12Status: Displays the MAC address of the access point that is associated with theDWL-G630.SSID: The Service Set Identifier is the name assigned to the wireless network. Thefactory SSID setting is set to default.Tx Rate: Tx Rate settings are automatically determined for an optimal speed up to amaximum of 54Mbps.Channel: The channel selection is automatically determined by the DWL-G630.Link Quality / Signal Strength: Displays the link quality for the DWL-G630 wirelessconnection to the access point. The signal strength represents the wireless signalbetween the access point and the DWL-G630. The percentage coincides with thegraphical bar.Data Rate: Displays the statistics of data transmitted and received.Configuration Utility (continued)Link InfoRescan: Rescans for the strongest signal in your environment and associates withthat access point or router.default
13SSID: Service Set Identifier is a name that identifies a wireless network. Access pointsand wireless devices attempting to connect to a specific WLAN (Wireless Local AreaNetwork) must use the same SSID.The default setting is default.Wireless Mode: Click on the pull-down menu; select from the following options:Infrastructure - Connecting to the WLAN using an access point. (This is thedefault setting.)Ad-Hoc - Wireless mode used when connecting directly to a computer equippedwith a wireless adapter in a Peer-to-Peer environment.Channel: The channel selection is automatically determined by the DWL-G630. In Ad-Hoc mode, the channel must be manually set to the same channel for each wirelessadapter.Tx Rate: Tx rates are automatically determined for an optimal speed up to 54Mbps.Continuous Access Mode - This default setting consumes the most power.Maximum Power Save - This setting consumes the least power.Power Save - This setting consumes a moderate amount of power.Configuration Utility (continued)D-Link AirPlus DWL-650+ 2.4GHz Wireless Cardbus AdapterConfigurationClick Apply to save the changes.Power Mode: Select from three modes:Preamble: Select Long or Short preamble. The Preamble defines the length of the CRCblock (Cyclic Redundancy Check is a common technique for detecting data transmissionerrors) for communication between the access point and the wireless network adapters.High network traffic areas should use the shorter preamble type.
14Configuration Utility (continued)D-Link AirPlus DWL-650+ 2.4GHz Wireless Cardbus AdapterEncryptionData Encryption – Enable WEP encryption by clicking on the box.Auth. mode – Choose one of the following Authorization modes:Open Authentication –Communicates the key across the network.Shared Authentication –Allows communication only with other devices withidentical WEP settings.Auto – Will automatically adjust to the Authentication mode of the wirelessclient.Default Key –Select one of 4 keys to be the default key.Network Key – Enter a key in either ASCII or hexadecimal format.Key Format –ASCII or hexadecimal.Key length –Select the key length, either 64- or 128-bits.Click Apply to save the changes.Hexadecimal digits consist of the numbers 0-9 and the letters A-FASCII (American Standard Code for Information Interchange) is a code forrepresenting English letters as numbers from 0-127
15Available NetworksThe top section of the window displays the Available Networks. Scroll up and downthe list and highlight the network to which you wish to connect. Click on the Connectbutton.ProfileIn the lower half of the screen, you can manage the profiles that you have created for thewireless network at home, at the office and in public places. Scroll up and down andhighlight the profile that you wish to configure. You can Add or Remove a profile, orconfigure the Properties of the profile in order to connect with an available network.Add, Connect and PropertiesClick on Add, Connect or Properties and the screen on the next page will appear.Configuration Utility (continued)Site Survey
16Configuration Utility (continued)Site Survey > Add, Connect or PropertiesIn this window you can configure all the properties of a profile in order to connect with anetwork of your choice.After you have entered your changes in this window, click OK to save the changes.
17The About screen gives you information about the Firmware and Utility Versions ofthe DWL-G630.Configuration Utility (continued)About
18In this section you will learn how to establish a network at home or work, using MicrosoftWindows XP.Note: Please refer to websites such as http://www.homenethelp.comand http://www.microsoft.com/windows2000 for information about networkingcomputers using Windows 2000/Me /98SE.Go to Start>Control Panel>Network Connections.Select Set up a home or small office network.Networking BasicsWhen this screen appears, click Next.Using the Network Setup Wizard in Windows XP
19Please follow all the instructions in this window:Networking Basics (continued)Click Next.In the following window, select the best description of your computer. If your computerconnects to the Internet through a router, select the second option as shown.Click Next.
20Enter a Computer description and a Computer name (optional.)Networking Basics (continued)Click Next.Enter a Workgroup name. All computers on your network should have the sameWorkgroup name.Click Next.
21Please wait while the Network Setup Wizard applies the changes.Networking Basics (continued)When the changes are complete, click Next.Please wait while the Network Setup Wizard configures the computer.This may take a few minutes.
22Networking Basics (continued)In the window below, select the option that fits your needs. In this example, Create aNetwork Setup Disk has been selected. You will run this disk on each of thecomputers on your network. Click Next.Insert a disk into the Floppy Disk Drive, in this case drive A.Click Next.
23Networking Basics (continued)Please read the information under Here’s how in the screen below. After you completethe Network Setup Wizard you will use the Network Setup Disk to run the NetworkSetup Wizard once on each of the computers on your network. To continue, clickNext.
24Networking Basics (continued)Please read the information on this screen, then click Finish to complete the NetworkSetup Wizard.The new settings will take effect when you restart the computer. Click Yes to restart thecomputer.You have completed configuring this computer. Next, you will need to run the NetworkSetup Disk on all the other computers on your network. After running the NetworkSetup Disk on all your computers, your new wireless network will be ready to use.
25Networking Basics (continued)Naming your ComputerTo name your computer in Windows XP, please follow these directions:Click Start (in the lower left corner of the screen).Right-click on My Computer.Select Properties and click.Select the ComputerName Tab in the SystemProperties window.You may enter a Com-puter Description if youwish; this field is optional.To rename the computerand join a domain, clickChange.
26Networking Basics (continued)Naming your ComputerChecking the IP Address in Windows XPThe wireless adapter-equipped computers in your network must be in the same IP ad-dress range (see Getting Started in this manual for a definition of IP address range.) Tocheck on the IP address of the adapter, please do the following:Right-click on theLocal AreaConnection iconin the task bar.Click on Status.Click OK.All computers on your networkmust have the sameWorkgroup name.Select Workgroup and enterthe name of the Workgroup.In this window, enter theComputer name.
27Networking Basics (continued)Checking the IP Address in Windows XPThis window will appear.Click theSupport tab.Click Close.Assigning a Static IP Address in Windows XP/2000Note: DHCP-capable routers will automatically assign IP addresses to the computers onthe network, using DHCP (Dynamic Host Configuration Protocol) technology. If you areusing a DHCP-capable gateway/router you will not need to assign static IP addresses.If you are not using a DHCP capable gateway/router, or you need to assign a static IPaddress, please follow these instructions:Go to Start.Double-click onControl Panel.
28Networking Basics (continued)Assigning a Static IP Address in Windows XP/2000Double-click onNetworkConnections.Double-click onProperties.Right-click on Local AreaConnections.
29Networking Basics(continued)You have completed the assignment of a static IP address. (You do not need to assigna static IP address if you have a DHCP-capable gateway/router.)Click on Internet Protocol(TCP/IP)Click Properties.IP Address:e.g., 192.168.0.2Subnet Mask:255.255.255.0Default Gateway:Enter the LAN IP address ofthe wireless router. (D-Linkwireless routers have a LAN IPaddress of 192.168.0.1). In the window below, select Use the following IP address. Input your IPaddress and subnet mask. (The IP addresses on your network must bewithin the same range. For example, if one computer has an IP address of192.168.0.2, the other computers should have IP addresses that aresequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must bethe same for all the computers on the network.)Click OK. Select Use the followingDNS server address. Enterthe LAN IP address of theWireless Router. (D-Linkwireless routers have a LANIP address of 192.168.0.1).D-Link AirPlus XtremeG DWL-650 Wireless Cardbus AdapterAssigning a Static IPAddressin Windows XP/2000
30Networking Basics (continued)Checking the Wireless Connection by Pinging inWindows XP/2000Checking the Wireless Connection by Pinging inWindows Me/98SEGo to Start > Run >type cmd. A windowsimilar to this onewill appear. Typepingxxx.xxx.xxx.xxx,where xxx is the IPaddress of thewireless router oraccess point. A goodwireless connectionwill show four repliesfrom the wirelessrouter or accesspoint, as shown.Go to Start > Run> type command.A window similar tothis will appear.Type pingxxx.xxx.xxx.xxxwhere xxx is the IPaddress of thewireless router oraccess point. Agood wirelessconnection willshow four repliesfrom the wirelessrouter or accesspoint, as shown.
311. How do I check that the drivers for the DWL-G630 are installed properly?Click DeviceManager.Select theHardwareTab.TroubleshootingThis chapter provides solutions to problems that can occur during the installation andoperation of the DWL-G630. Read the following descriptions if you are having problems.(The examples below are illustrated in Windows XP. If you have a different operatingsystem, the screens on your computer will look similar to the following examples.)Go to Start > MyComputer >Properties.
32Troubleshooting (continued)Double-clickon NetworkAdapters.Right-click on D-LinkDWL-G630 WirelessCardbus Adapter.Select Propertiesto check that thedrivers are in-stalled properly.Click OK.D-Link AirPro DWL-AB650 Wireless Cardbus AdapterLook under Devicestatus to check thatthe device is workingproperly.D-Link DWL-G630 Wireless Cardbus AdapterD-Link AirPlus G DWL-G630D-Link AirPlus G DWL-G630)802.11g/2.4GHz Wireless Cardbus AdapterTM
33Troubleshooting (continued)Make sure that the DWL-G630 Wireless Cardbus Adapter is properly seatedin the computer’s cardbus slot.If Windows does not detect the hardware upon insertion of the adapter,make sure to completely remove drivers that were previously loaded. Toremove the drivers, do the following: 5. What should I do when the computer does not recognize the DWL-G630 Wireless Cardbus Adapter?4. I forgot my Encryption key. What should I do?Reset the access point to its factory default settings and restore the DWL-G630 Wireless Cardbus Adapter to the factory default settings.3. Why aren’t the Power and Link lights on?Check to see if the DWL-G630 Wireless Cardbus Adapter is firmlyinserted into the Cardbus slot of your laptop computer.2. Why can’t I connect to the access point or the wireless router?Make sure that the SSID on the DWL-G630 Wireless Cardbus Adapter isexactly the same as the SSID on the access point or wireless router.Move the DWL-G630 and the access point or wireless router into thesame room and then test the wireless connection.Disable all security settings. (WEP, MAC address control, AES).Make sure that the access point/router is not set to a different frequency.Turn off your access point and the computer with the DWL-G630. Turn onthe access point, and then turn on the computer with the DWL-G630.Refresh the DWL-G630 Utility.
34Check that the LED indicators for the broadband modem are indicatingnormal activity. If not, there may be a problem with the broadbandconnection.Check that the LED indicators on the wireless router are functioning properly.If not, check that the AC power and Ethernet cables are firmly connected.Check that the IP address, subnet mask, gateway, and DNS settings arecorrectly entered for the network.In Infrastructure mode, make sure the same Service Set Identifier (SSID)is specified on the settings for the wireless clients and access points. TheSSID factory default setting for most D-Link products is default. (Double-click on the WLAN icon in the taskbar. The Link Info screen will displaythe SSID setting.)In Ad-Hoc mode, both wireless clients will need to have the same SSID.Please note that it might be necessary to set up one client to establish aBSS (Basic Service Set) and wait briefly before setting up other clients.This prevents several clients from trying to establish a BSS at the sametime, which can result in multiple singular BSSs being established, ratherthan a single BSS with multiple clients associated to it.Troubleshooting (continued)A. Under Tools> select Folder Options…> select View > underHidden files and folders > select Show hidden files andfolders.B. Uncheck Hide extension for known file types > click onApply.C. Search for previously loaded driver files. Remove these filesfrom the INF and SYSTEM32 (DRIVERS) folders in the Windowsdirectory. Note: Windows XP and Windows 2000 will rename.inf files that have not received WHQL certification into oem.inffiles (e.g., oem1.inf.)6. What should I do when the computer with the DWL-G630 installed is unable to connect to the wireless network and/or the Internet?
35Check that the Network Connection for the wireless client is configuredproperly. Select AP (Infrastructure) when connecting to an access pointand select Ad-Hoc mode when connecting without an access point. Double-click on the WLAN icon in the taskbar > click on Configuration to changethe settings for the wireless adapter.If Security is enabled, make sure that the correct encryption keys areentered on both the DWL-G630 and the access point. Double-click on theWLAN icon in the taskbar > click Encryption. Check to see that the keyselected is set to the same key as other devices on the network.7. How can I troubleshoot distance issues using the DWL-G630?Move the DWL-G630 and access point or wireless router into the sameroom and then test the wireless connection.Change the channel of the access point.Move devices within the line of sight.Troubleshooting (continued)
36IEEE 802.11bIEEE 802.11gIEEE 802.11StandardsTechnical SpecificationsPower/StatusLinkDiagnostic LEDTemperature Operating: 0ºC to 55ºC (32ºF to 131ºF)5%-95% maximum, non-condensingHumidity:Warranty: 3 years 0.12 lb. (55 grams)Weight:Antenna Type:Built-in diversity patch antenna, 2dBi gain (max.)32-bit CardbusBus Type:Security:Physical Dimensions:L = 4.69 inches (119mm)W = 2.13 inches (54mm)H = 0.47 inches (12mm)64-,128-bit WEP Encryption Storage: -20ºC to 65ºC (-4ºF to 149ºF)
37Technical Specifications (continued)Power:3.3 Volt ± 5%Data Modulation Type:DBPSK, DQPSK, CCK and OFDM(BPSK/QPSK/16-QAM/64-QAM)Channels:1-11 channels (North America)Power Consumption:802.11g: TX 550mA, RX 330mA, Standby 300mA802.11b: TX 580mA, RX 350mA, Standby 300mARegulation Compliant:Wireless: Wi-FiUS: FCC part 15 class B, Sec. 15.247, 15.109Sensitivity for 802.11b:11Mbps (CCK): -84dBm5.5Mbps (CCK): -86dBm2Mbps (DQPSK): -88dBm1Mbps (DBPSK): -89dBmtypically @PER <8% packet size 1024 and @25°Sensitivity for 802.11g:54Mbps (OFDM): -69dbm48Mbps (OFDM): -70dbm36Mbps (OFDM): -74dbm24Mbps (OFDM): -77dbm12Mbps (OFDM): -83dbm6Mbps (OFDM): -85dbmtypically @PER <8% packet size 1024 and @25°Configuration:Plug & Play setup and installationNetwork:Auto-switch to use 802.11g or 802.11b mode
38Technical Specifications (continued)Data Rates:With Automatic Fallback54Mbps; 48Mbps; 36Mbps; 24Mbps; 18Mbps; 12Mbps; 11Mbps;9Mbps; 6Mbps; 5.5Mbps; 2Mbps; 1MbpsRange:*Indoors: Up to 328 feet (100 meters)Frequency Range:2.4GHz to 2.462GHz*Environmental factors may adversely affect range.Modulation Technology:Orthogonal Frequency Division Multiplexing (OFDM)15dBm ± 2dBTransmitter Output Power:
39Technical SupportYou can find software updates and user documentation on the D-Link website.D-Link provides free technical support for customers within the United States andwithin Canada for the duration of the warranty period on this product.U.S. and Canadian customers can contact D-Link technical support through ourwebsite, or by phone.Tech Support for customers within the United States:D-Link Technical Support over the Telephone:(877) 453-546524 hours a day, seven days a week.D-Link Technical Support over the Internet:http://support.dlink.comemail:support@dlink.comTech Support for customers within Canada:D-Link Technical Support over the Telephone:(800) 361-5265Monday to Friday 8:30am to 9:00pm ESTD-Link Technical Support over the Internet:http://support.dlink.caemail:support@dlink.ca
40Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limitedwarranty for its product only to the person or entity that originally purchased the product from:•D-Link or its authorized reseller or distributor and•Products purchased and delivered within the fifty states of the United States, the District ofColumbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with anAPO or FPO.Limited Warranty: D-Link warrants that the hardware portion of the D-Link products describedbelow will be free from material defects in workmanship and materials from the date of original retailpurchase of the product, for the period set forth below applicable to the product type (“WarrantyPeriod”), except as otherwise stated herein.3-Year Limited Warranty for the Product(s) is defined as follows:•Hardware (excluding power supplies and fans) Three (3) Years•Power Supplies and Fans One (1) Year•Spare parts and spare kits Ninety (90) daysD-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Periodat no charge to the original owner or to refund at D-Link’s sole discretion. Such repair or replacement willbe rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not benew or have an identical make, model or part. D-Link may in its sole discretion replace the defectiveHardware (or any part thereof) with any reconditioned product that D-Link reasonably determines issubstantially equivalent (or superior) in all material respects to the defective Hardware. Repaired orreplacement Hardware will be warranted for the remainder of the original Warranty Period from the dateof original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its solediscretion that it is not practical to repair or replace the defective Hardware, the price paid by the originalpurchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defectiveHardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price isrefunded, shall become the property of D-Link upon replacement or refund.Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”)will substantially conform to D-Link’s then current functional specifications for the Software, as set forthin the applicable documentation, from the date of original retail purchase of the Software for a period ofninety (90) days (“Warranty Period”), provided that the Software is properly installed on approvedhardware and operated as contemplated in its documentation. D-Link further warrants that, during theWarranty Period, the magnetic media on which D-Link delivers the Software will be free of physicaldefects. D-Link’s sole obligation shall be to replace the non-conforming Software (or defective media)with software that substantially conforms to D-Link’s functional specifications for the Software or torefund at D-Link’s sole discretion. Except as otherwise agreed by D-Link in writing, the replacementSoftware is provided only to the original licensee, and is subject to the terms and conditions of thelicense granted by D-Link for the Software. Software will be warranted for the remainder of the originalWarranty Period from the date or original retail purchase. If a material non-conformance is incapable ofcorrection, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will berefunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returnedto D-Link. The license granted respecting any Software for which a refund is given automaticallyterminates.Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and softwareof D-Link’s products will not be applied to and does not cover any refurbished product and any productpurchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers,or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case,the product is being sold “As-Is” without any warranty whatsoever including, without limitation, theLimited Warranty as described herein, notwithstanding anything stated herein to the contrary.Submitting A Claim: The customer shall return the product to the original purchase point based on itsreturn policy. In case the return policy period has expired and the product is within warranty, thecustomer shall submit a claim to D-Link as outlined below:Warranty and Registration(USA only)
41•The customer must submit with the product as part of the claim a written description of theHardware defect or Software nonconformance in sufficient detail to allow D-Link to confirmthe same.•The original product owner must obtain a Return Material Authorization (“RMA”) number fromthe Authorized D-Link Service Office and, if requested, provide written proof of purchase ofthe product (such as a copy of the dated purchase invoice for the product) before thewarranty service is provided.•After an RMA number is issued, the defective product must be packaged securely in theoriginal or other suitable shipping package to ensure that it will not be damaged in transit, andthe RMA number must be prominently marked on the outside of the package. Do not include anymanuals or accessories in the shipping package. D-Link will only replace the defective portionof the Product and will not ship back any accessories.•The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery(“COD”) is allowed. Products sent COD will either be rejected by D-Link or become theproperty of D-Link. Products shall be fully insured by the customer. D-Link will not be heldresponsible for any packages that are lost in transit to D-Link. The repaired or replacedpackages will be shipped to the customer via UPS Ground or any common carrier selected byD-Link, with shipping charges prepaid. Expedited shipping is available if shipping charges areprepaid by the customer and upon request.•Return Merchandise Ship-To AddressUSA: 17595 Mt. Herrmann, Fountain Valley, CA 92708-4160Canada: 2180 Winston Park Drive, Oakville, ON, L6H 5W1 (Visit http://www.dlink.ca for detailedwarranty information within Canada)D-Link may reject or return any product that is not packaged and shipped in strict compliance with theforegoing requirements, or for which an RMA number is not visible from the outside of the package. Theproduct owner agrees to pay D-Link’s reasonable handling and return shipping charges for any productthat is not packaged and shipped in accordance with the foregoing requirements, or that is determinedby D-Link not to be defective or non-conforming.What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Link’sjudgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse,faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in thedocumentation for the product, or if the model or serial number has been altered, tampered with, defacedor removed; Initial installation, installation and removal of the product for repair, and shipping costs;Operational adjustments covered in the operating manual for the product, and normal maintenance;Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage;Any hardware, software, firmware or other products or services provided by anyone other than D-Link; Products that have been purchased from inventory clearance or liquidation sales or other sales inwhich D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to theproduct. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void thisWarranty.Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THEPRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING,WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSEAND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORYWHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TONINETY (90) DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDEDHEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT ISWITH THE PURCHASER OF THE PRODUCT.Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLEUNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORYFOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER,WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO,DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTERFAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON,OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTINGFROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANYBREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OFSUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY ISREPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM
42Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Somestates do not allow exclusion or limitation of incidental or consequential damages, or limitations on howlong an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limitedwarranty provides specific legal rights and the product owner may also have other rights which varyfrom state to state.Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registeredtrademarks are the property of their respective manufacturers or owners.Copyright Statement: No part of this publication or documentation accompanying this Product maybe reproduced in any form or by any means or used to make any derivative such as translation,transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., asstipulated by the United States Copyright Act of 1976. Contents are subject to change without priornotice. Copyright© 2002 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radiointerference, in which case the user may be required to take adequate measures.FCC Statement: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates, uses, andcan radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communication. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.•Consult the dealer or an experienced radio/TV technician for help.For detailed warranty outside the United States, please contact corresponding localD-Link office.Register your D-Link product online at http://support.dlink.com/register/ (12/18/2003)FCC Caution:(1) The devices are restricted to indoor operations within the 5.15 to 5.25GHz range. (2) For thisdevice to operate in the 5.15 to 5.25GHz range, the devices must use integral antennas.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation. LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCTCOVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIESARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED ORSTATUTORY.The manufacturer is not responsible for any radio or TV interference caused by unauthorizedmodifications to this equipment; such modifications could void the user’s authority to operate theequipment.IMPORTANT NOTE:FCC Radiation Exposure Statement:This device has been tested for compliance with FCC RF Exposure (SAR) limits in the typical laptopcomputer configuration and this device can be used in substantially similar laptop computers with sidemounted PCMCIA slots. This device cannot be used with handheld PDAs (personal digital assistants) orother portable host devices. This device and its antenna must not be co-located or operated in conjunctionwith any other antenna or transmitter.
Portable of end product Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu