D Link HP1565A1 Wireless N Powerline Gigabit Router User Manual
D Link Corporation Wireless N Powerline Gigabit Router
D Link >
User Manual
iD-Link DHP-1565 User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization
of such revisions or changes.
Manual Revisions
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2011 by D-Link Systems, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc.
Revision Date Description
1.0 September 12, 2011 DHP-1565 Revision A1
Preface
iiD-Link DHP-1565 User Manual
Table of Contents
Preface ........................................................................................................... i
Manual Revisions ...............................................................................................i
Trademarks ..........................................................................................................i
Product Overview ....................................................................................... 1
Package Contents ........................................................................................... 1
System Requirements .................................................................................... 2
Introduction ...................................................................................................... 3
Features ..............................................................................................................4
Hardware Overview ........................................................................................ 5
Connections .............................................................................................5
LEDs ............................................................................................................6
Installation ................................................................................................... 7
Before you Begin ............................................................................................. 7
Wireless Installation Considerations ........................................................ 8
Hardware Installation - For Router Mode ...............................................9
Connect to Cable/DSL/Satellite Modem ...............................................10
Connect to Another Router .......................................................................11
Hardware Installation - For Access Point Mode ..................................13
PowerLine Installation Considerations ..................................................14
PowerLine Security .......................................................................................15
PowerLine Network-Quick Setup ...................................................15
Encryption Button Usage ............................................................15
PowerLine Network Device Setup .................................................16
Getting Started ..............................................................................................17
Conguration (Router Mode) .................................................................18
Web-based Conguration Utility .............................................................18
Setup ..................................................................................................................19
Internet ....................................................................................................19
Internet Connection Setup Wizard ................................................20
Manual Internet Connection Setup ...............................................26
Static IP ...............................................................................................27
Dynamic IP (DHCP) ........................................................................28
PPPoE (Username/Password) .....................................................29
PPTP ....................................................................................................31
L2TP .....................................................................................................33
DS-Lite ................................................................................................35
Wireless Settings ..................................................................................36
Manual Wireless Settings ..................................................................37
802.11n/b/g (2.4GHz) ....................................................................37
Network Settings..................................................................................39
Router Settings ................................................................................40
DHCP Server Settings....................................................................41
DHCP Reservation ..........................................................................42
IPv6 .....................................................................................................................43
IPv6 over PPPoE ..............................................................................46
Static IPv6 ..........................................................................................47
Tunneling Connection (6rd) .......................................................48
IPv6 ......................................................................................................49
Link-local Only .................................................................................49
IPv6 Manual Setup ........................................................................................50
Table of Contents
iiiD-Link DHP-1565 User Manual
Table of Contents
Auto Detection ................................................................................50
Static IPv6 ..........................................................................................51
Autoconguration..........................................................................52
PPPoE ..................................................................................................53
IPv6 in IPv4 Tunneling...................................................................55
6 to 4 Tunneling ..............................................................................56
6rd ........................................................................................................57
PLC Settings (Router Mode) ......................................................................58
Advanced .........................................................................................................61
Virtual Server .........................................................................................61
Port Forwarding ....................................................................................63
Application Rules .................................................................................64
QoS Engine .............................................................................................65
Network Filter ........................................................................................67
Access Control .......................................................................................68
Access Control Wizard...................................................................68
Website Filter .........................................................................................71
Inbound Filter ........................................................................................72
Firewall Settings ...................................................................................73
Routing ....................................................................................................75
Advanced Wireless Settings .............................................................76
802.11n/b/g (2.4GHz) ....................................................................76
Wi-Fi Protected Setup (WPS) ............................................................77
Advanced Network ..............................................................................79
UPnP ....................................................................................................79
Internet Ping Block.........................................................................79
Internet Port Speed .......................................................................79
Multicast Streams ...........................................................................79
Guest Zone ......................................................................................................80
IPv6 Firewall ....................................................................................................81
IPv6 Routing ...................................................................................................82
Tools ...................................................................................................................83
Admin .......................................................................................................83
Time ..........................................................................................................84
SysLog ......................................................................................................85
Email Settings ........................................................................................86
System ......................................................................................................87
Firmware..................................................................................................88
Dynamic DNS .........................................................................................89
System Check ........................................................................................90
Schedules ................................................................................................91
Status .................................................................................................................92
Device Info ..............................................................................................92
Logs ...........................................................................................................93
Statistics ...................................................................................................94
Internet Sessions ..................................................................................95
Routing Table .........................................................................................96
Wireless ....................................................................................................97
IPv6 ............................................................................................................98
IPv6 Routing ...........................................................................................99
Support ................................................................................................ 100
Wireless Connection Setup Wizard ......................................................101
Wireless Security Setup Wizard .............................................................102
Add Wireless Device with WPS Wizard................................................ 104
Conguration (AP Mode)......................................................................... 105
Web-based Conguration Utility .......................................................... 105
Wireless Setup Wizard .............................................................................. 106
Wireless Setup .............................................................................. 108
ivD-Link DHP-1565 User Manual
Table of Contents
Network Settings - DHCP .......................................................... 110
Network Setup - Static IP .......................................................... 111
Conguration ..........................................................................................114
PLC Settings - AP Mode ............................................................................ 114
Network Filter .............................................................................. 117
Advanced Wireless ...................................................................... 118
Wi-Fi Protect Setup ..................................................................... 119
Add Wireless Device with WPS .....................................................120
Adding a Wireless Device Using the PIN Method ............ 120
Adding a Wireless Device Using the PBC Method ........... 121
Manually Add Wireless Device with WPS.................................. 122
User Limit Settings ..................................................................................... 123
Admin ..............................................................................................124
Time .................................................................................................. 125
System Settings ............................................................................126
Firmware ......................................................................................... 127
Language Pack ............................................................................. 127
System Check ............................................................................... 128
Schedules ....................................................................................... 129
Status ........................................................................................................130
Device Info ..................................................................................... 130
Logs ..................................................................................................131
Statistics .......................................................................................... 132
Wireless ................................................................................................. 133
IPv6 ......................................................................................................... 134
Support .......................................................................................................... 135
Wireless Security .....................................................................................136
What is WPA? ................................................................................................ 136
Congure WEP ............................................................................................. 137
Congure WPA/WPA2-Personal (PSK) .................................................138
Congure WPA/WPA2-Enterprise (RADIUS) ...................................... 139
Connect to a Wireless Network ............................................................140
Using Windows® 7 ...................................................................................... 140
Congure WPS ...................................................................................143
Using Windows Vista® ...............................................................................147
Congure Wireless Security ...........................................................148
Using Windows® XP ................................................................................... 150
Congure WPA-PSK ..........................................................................151
Troubleshooting .....................................................................................153
Wireless Basics ........................................................................................157
What is Wireless? ........................................................................................158
Tips ..................................................................................................................160
Wireless Modes ........................................................................................... 161
Networking Basics ..................................................................................162
Check your IP address ...............................................................................162
Statically Assign an IP address ............................................................... 163
Technical Specications ........................................................................164
Contacting Technical Support ..............................................................166
Warranty ...................................................................................................167
Registration .............................................................................................173
1D-Link DHP-1565 User Manual
Section 1 - Product Overview
Product Overview
Note: Using a power supply with a dierent voltage rating than the one included with the DHP-1565 will cause damage and void the
warranty for this product.
Package Contents
DHP-1565 Wireless N PowerLine Gigabit Router
Ethernet Cable
Power Adapter
CD-ROM with Manual and Setup Wizard
QIG
2D-Link DHP-1565 User Manual
Section 1 - Product Overview
Network Requirements
• An Ethernet-based Cable or DSL modem
• IEEE 802.11n or 802.11g wireless clients
• 10/100/1000 Ethernet
Web-based Conguration
Utility Requirements
Computer with the following:
• Windows®, Macintosh, or Linux-based operating system
• An installed Ethernet adapter
Browser Requirements:
• Internet Explorer 6 or higher
• Firefox 3.0 or higher
• Safari 3.0 or higher
• Chrome 2.0 or higher
Windows® Users: Make sure you have the latest version of Java
installed. Visit www.java.com to download the latest version.
CD Installation Wizard
Requirements
Computer with the following:
• Windows® 7/ Vista® / XP with Service Pack 3
• An installed Ethernet adapter
• CD-ROM drive
System Requirements
3D-Link DHP-1565 User Manual
Section 1 - Product Overview
Introduction
TOTAL PERFORMANCE
Combines PowerLine features and IEEE 802.11n/g wireless technology to provide the best wire and wireless performance.
TOTAL SECURITY
The most complete set of security features including Active Firewall and WPA/WPA2 to protect your network against outside intruders.
TOTAL COVERAGE
Provides greater wireless signal rates and powerline in areas where a wired connection would be benecial like had-to-reach areas in your home
for best-in-class Whole Home Coverage.
ULTIMATE PERFORMANCE
The D-Link Wireless N PowerLine Gigabit Router (DHP-1565) is a 802.11n compliant device that delivers real world performance of up to 14x faster
than an 802.11g wireless connection (also faster than a 1000Mbps wired Ethernet connection). Create a secure wireless network to share photos,
les, music, video, printers, and network storage throughout your home. Connect the DHP-1565 router to a cable or DSL modem and share your
high-speed Internet access with everyone on the network. In addition, this Router includes a Quality of Service (QoS) engine that keeps digital
phone calls (VoIP) and online gaming smooth and responsive, providing a better Internet experience. PowerLine uses a building’s existing electrical
wiring to turn any power outlet into a fully functioning Ethernet port and transform your entire home into a wall-to-wall network, instantly. Now
you can take that same revolutionary PowerLine technology and give up to 4 of your favorite connected devices their own Gigabit Ethernet port
with 500Mbps speed, and QoS prioritization experience seamless digital entertainment and performance anywhere in your home.
TOTAL NETWORK SECURITY
The Wireless N PowerLine Gigabit Router supports all of the latest wireless security features to prevent unauthorized access, be it from over the
wireless network or from the Internet. Support for WPA/WPA2 standards ensure that you’ll be able to use the best possible encryption method,
regardless of your client devices. In addition, this router utilizes dual active rewalls (SPI and NAT) to prevent potential attacks from across the Internet.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely
aect wire and wireless signal range.
4D-Link DHP-1565 User Manual
Section 1 - Product Overview
• Faster Wireless Networking - The DHP-1565 provides up to 300Mbps* wireless connection with other 802.11n wireless clients.
This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time
audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds 650% faster than
802.11g.
• Compatible with 802.11g Devices - The DHP-1565 is still fully compatible with the IEEE 802.11g standards, so it can connect with
existing 802.11g PCI, USB, and Cardbus adapters.
• Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features
including:
• Content Filtering - Easily applied content ltering based on MAC Address, URL, and/or Domain Name.
• Filter Scheduling - These lters can be scheduled to be active on certain days or for a duration of hours or minutes.
• Secure Multiple/Concurrent Sessions - The DHP-1565 can pass through VPN sessions. It supports multiple and
concurrent IPSec and PPTP sessions, so users behind the DHP-1565 can securely access corporate networks.
• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DHP-1565 lets you control what information
is accessible to those on the wireless network, whether from the Internet or from your company’s server. Congure your router to
your specic settings within minutes.
• Faster Powerline Networking - Built-in PowerLine Router capabilities work seamlessly with D-Link’s PowerLine AV adapters
(must be purchased separately) that extend your network to the farthest corners of your home using the electrical wiring already
installed in your walls. Simply connect your router (DHP-1565) and plug it into a power outlet to turn every other power outlet in
your home into a possible network connection with speeds up to 500Mbps - fast enough to stream HD video and share large les.
Since it is compliant with the HomePlug AV standard, you can use it to extend an existing PowerLine network², or simply create a
new one. It turns every power outlet into a possible network connection so you can access digital media devices, game consoles,
print servers, computers and network storage devices from any room in your home.
* Maximum wireless signal rate derived from IEEE Standard 802.11g, and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely
aect wireless signal range.
Features
5D-Link DHP-1565 User Manual
Section 1 - Product Overview
Hardware Overview
Connections
1AP-Router Switch Two-way switch used to Select AP or Router Mode.
2LAN Ports (1-4) Connect 10/100/1000 Ethernet devices such as computers, switches, and hubs.
3Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem.
4Reset Button Pressing the Reset button restores the router to its original factory default settings.
5USB USB 1.1/2.0 port for SharePortTM Network and WCN support.
6Power Button Use this switch to power on/power o the device.
7Power Receptor Receptor for the supplied power cord.
8
WPS Button
Press the WPS button for one second to initiate the WPS process. The button will ash blue while a WPS connection
is being established. The button will light solid blue for 5 seconds when the device has successfully been added to
the network.
Simple Connect Button Push this button to establish a secure PowerLine network with other PowerLine AV devices.
23456
1 7
8
6D-Link DHP-1565 User Manual
Section 1 - Product Overview
1Power LED A solid green light indicates a proper connection to the power supply. This LED will light orange during a factory reset or
reboot. A slow blinking orange LED indicates that the Router has crashed during bootup.
2Internet LED A solid green light indicates that the internet connection has successfully completed. This LED blinks green during data
transmission. A solid orange light indicates that the physical link is up, but the ISP service is down.
3PowerLine AV LED A solid light indicates that a PowerLine connection is established. The LED will blink quickly when data is transmitted to or
from another PowerLine unit.
Hardware Overview
LEDs
12
3
7D-Link DHP-1565 User Manual
Section 2 - Installation
Before you Begin
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area
such as a closet, cabinet, or in the attic or garage.
• Please congure the router with the computer that was last connected directly to your modem.
• You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must
turn o your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn
the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
• If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump,
or Enternet 300 from your computer or you will not be able to connect to the Internet.
• When running the Setup Wizard from the D-Link CD, make sure the computer you are running the CD from is connected to the
Internet and online or the wizard will not work. If you have disconnected any hardware, re-connect your computer back to the
modem and make sure you are online.
8D-Link DHP-1565 User Manual
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your
wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must
pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your
home or business. The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling
can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is
minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be
almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will
travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a dierence. A solid metal door or aluminum studs may have a negative eect on range. Try to position
access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects
such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade your
wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.
5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems),
your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from
your wireless devices as possible. The base transmits a signal even if the phone in not in use. Please refer to page 20 for detail
information.
9D-Link DHP-1565 User Manual
Section 2 - Installation
Hardware Installation - For Router Mode
Network Diagram
Windows users can use the Quick Router Setup Wizard (from the CD) to congure their router. If you do not want to use the wizard, lost your CD, or are
running Mac or Linux, you will need to use the manual setup procedure below.
Start Here
Quick Router Setup Wizard
For the Wizard to work, the computer must be connected to the Internet and be online. If you have disconnected any hardware, please re-connect your
computer back into the modem and make sure you are online.
Insert the CD into your drive on a computer that is online and click Install Router to start the Quick Router Setup Wizard. Follow the onscreen instructions
to install and congure your router.
Laptop
1234 LAN INTERNET
RESET
ON/OFFUSB
AR RT
AC IN
INTERNET
DHP-1565
PC
10D-Link DHP-1565 User Manual
Section 2 - Installation
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Unplug the Ethernet cable from the computer (or existing router if upgrading) that is connected to your modem. Then, plug it into
the yellow port labeled INTERNET on the back of the D-Link Wireless N PowerLine Gigabit Router. The Modem is now connected
to your Wireless N PowerLine Gigabit Router (DHP-1565).
3. Plug one end of the included blue Ethernet cable that came with your router into the blue port labeled LAN on the back of the
D-Link Wireless N PowerLine Gigabit Router. Plug the other end of this cable into the Ethernet port on your computer. Turn on the
computer. Reconnect the power adapter to your cable or DSL modem and wait for 2 minutes. Let it complete its connection to
your ISP before proceeding to the next step.
4. Connect the supplied power cord into the power receptor located on the back of the Wireless N PowerLine Gigabit Router (DHP-
1565) and then plug into a wall outlet (Please do not use a power strip or a surge protector). Turn on the DHP-1565 Router by
pushing the power button located on the back of this unit.
Note: Power source is conrmed when the green LED Power Indicator on the Wireless N PowerLine Gigabit Router is illuminated.
5. Open a web browser, enter http://192.168.0.1 (or http://dlinkrouter) and then press Enter. When the login window appears, set
the user name to Admin and leave the password box blank. Click Log In to continue the Internet Connection setup wizard. This
wizard will walk you through a step-by-step process to congure Wireless N PowerLine Gigabit Router (DHP-1565) and connect
to the Internet. Please refer to page 19 for detailed information.
Note: To run the Wireless Connection Setup Wizard, click the Wireless Connection Setup Wizard button in the Setup Wireless
Settings window. This wizard will walk you through a step-by-step process to congure your wireless settings. Please refer to
page 35 for detailed information.
Connect to Cable/DSL/Satellite Modem
11D-Link DHP-1565 User Manual
Section 2 - Installation
If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before
connecting the router to your network:
• Disable UPnP™
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address
from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router and use the power switch to power up the router. Connect one of your computers to the router (LAN port) using
an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking
Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most
cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer.
2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to Admin and leave the
password box empty. Click Log In to continue.
3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings to continue.
4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server checkbox. Click Save Settings to continue.
5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your settings. Use this
new IP address to access the conguration utility of the router in the future. Close the browser and change your computer’s IP settings back to
the original values as in Step 1.
Connect to Another Router
12D-Link DHP-1565 User Manual
Section 2 - Installation
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet
(WAN) port of the D-Link router.
8. You may now use the other 2 LAN ports to connect other Ethernet devices and computers. To congure your wireless network, open a web
browser and enter the IP address you assigned to the router. Refer to the Conguration and Wireless Security sections for more information
on setting up your wireless network.
13D-Link DHP-1565 User Manual
Section 2 - Installation
Hardware Installation - For Access Point Mode
Step 1
Plug the DHP-1565 in the same room as your existing PowerLine Network in order to verify whether your home’s electrical wiring is suitable for the
Powerline Network. Once congured you may place your DHP-1565 to the location of your choice.
Step 2
Move the switch on the back of the DHP-1565 to “AP”. Connect the supplied power cord into the power receptor located on the back of the DHP-
1565 and plug into a wall outlet (Please do not plug to power strip or surge protector). Turn on the DHP-1565 by pushing the power button located
on the back of this unit.
Note: Power source is conrmed when the green LED Power Indicator on the DHP-1565 is illuminated. Network Connectivity is conrmed when the
PowerLine AV LEDs indicators on the DHP-1565 and PowerLine AV device are illuminated.
Step 3
If you applied security on your other PowerLine devices and you have plugged in your new D-Link Wireless N PowerLine Gigabit Router, press
the Simple Connect Button on the DHP-1565 for 2 seconds. The Power LED will start blinking after you release the button. Within 2 minutes of
pushing the Simple Connect Button on the DHP-1565, press the Simple Connect Button on the additional PowerLine AV device(s) in your existing
PowerLine network for 2 seconds. The Power LED will start blinking after you release the button. Network Connectivity is conrmed when the
PowerLine AV LEDs indicators on the DHP-1565 and PowerLine AV device are illuminated.
Step 4
After the network security setup steps, your PowerLine network will be securely congured with the same network encryption key. Place DHP-
1565 in a dierent area in your home. The DHP-1565 will retain the security settings even if they are unplugged. Plug power cord into a wall outlet
(Please do not plug to power strip or surge protector). Connect one end of the included Ethernet cable to the blue port labeled LAN on the back
of DHP-1565 and attach the other end of the Ethernet cable to the PC, game console, or IP Camera as illustrated in Room 2.
Step 5
Open a web browser, enter http://dlinkrouterWXYZ (WXYZ: four-digit sux of the PLC MAC Address) and then press Enter. When the login window
appears, Set the user name to Admin and leave the password box blank. Click Log In to continue the setup. To run the Wireless Connection Setup
Wizard, click the Wireless Connection Setup Wizard button in the Setup -> Wireless Settings window. This wizard will walk you through a step-
by-step process to congure your wireless setting.
14D-Link DHP-1565 User Manual
Section 1 - Product Overview
PowerLine Installation Considerations
Plan the location of your PowerLine devices:
1. Connect the PowerLine devices to electrical outlets that are not controlled by a wall switch in order to avoid accidentally turning o the power
to the device.
2. Do not connect the Wireless N PowerLine Gigabit Router to an extension cord, surge protector, or power strip. This might prevent the device
from working correctly or it may reduce the network performance.
3. Avoid using the Wireless N PowerLine Gigabit Router in an electrical outlet that is located near an appliance that uses a lot of power, such as a
washer, dryer or refrigerator. This may prevent the adapter from working correctly, or may negatively impact the network performance.
4. Verify that your PowerLine devices are electrically rated to operate with the power available in your location.
5. To help prevent against electrical shock, be sure to plug the power cables into properly grounded electrical outlets.
15D-Link DHP-1565 User Manual
Section 1 - Product Overview
PowerLine Security
It is strongly recommended to encrypt your PowerLine network. By encrypting the data that is sent via your PowerLine adapters, you will prevent
nearby hackers with a Powerline adapter to connect to your network and steal your information.
To encrypt your PowerLine network, follow the steps below:
PowerLine Network-Quick Setup
The Simple Connect Button is used to add a PowerLine AV device to a PowerLine network. You can allow the DHP-1565 to join a network by pressing
the Simple Connect Button to toggle it to the Broadcast state or Join state.
The Simple Connect Button has 3 dierent trigger states:
Broadcast state- Enables the DHP-1565 to provide information for another PowerLine AV device to join its PowerLine network (works
even if it is the only device existing within the network group). The rst PowerLine device will use this state when the Simple Connect
Button is pressed.
Join State - This allows an ungrouped PowerLine AV device to join an existing PowerLine network. PowerLine devices added after
the rst device will be in the Join State when the Simple Connect Button is pressed.
Ungroup State - Hold down the Simple Connect Button for more than 10 seconds to detach the device from its network group.
Encryption Button Usage
16D-Link DHP-1565 User Manual
Section 1 - Product Overview
Note: A minimum of two PowerLine AV devices are required to create a network in order for your product to work properly.
Step 1
Plug the other PowerLine AV devices in the same room to verify if your home’s electrical wiring is suitable for the PowerLine Network. Once
congured you may place your PowerLine AV devices in the location of your choice. Plug one end of the Ethernet cable into the Ethernet port on
the PowerLine AV device.
Step 2
Press the Simple Connect Button located on the back panel of the DHP-1565 for 2 seconds. The Power LED will start blinking after you release
the button. Within 2 minutes of pushing the Simple Connect Button on the DHP-1565, press the Simple Connect Button on the second
PowerLine AV device(s) in your existing PowerLine network for 2 seconds. The Power LED will start blinking after you release the button. Network
Connectivity is conrmed when the PowerLine AV LEDs indicators on the DHP-1565 and PowerLine AV device are illuminated.
Step 3
After the network security setup steps, your PowerLine network will be securely congured with the same network encryption key. Place any
additional PowerLine AV devices in a dierent area of your home. The PowerLine AV devices will save the security settings even if they are unplugged.
Step 4
If your network has more than two PowerLine AV devices, press the Simple Connect Button on the DHP-1565 for 2 seconds. Within 2 minutes
of pushing the Simple Connect Button on the DHP-1565, press the Simple Connect Button on any additional PowerLine AV devices in your existing
PowerLine network for 2 seconds.
Network Connectivity is conrmed when the PowerLine AV LEDs indicators on the DHP-1565 and PowerLine AV device are illuminated. After
the network security setup steps, you can place any additional PowerLine AV devices in a dierent area of your home. The PowerLine AV devices
will save the security settings even if they are unplugged.
PowerLine Network Device Setup
17D-Link DHP-1565 User Manual
Section 2 - Installation
The DHP-1565 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you
quickly through the installation process.
Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. The steps
and screens are similar for the other Windows operating systems.
If the CD Autorun function does not automatically start on your computer, go to Start > Run. In the run box type“D:\autorun.exe” (where D:
represents the drive letter of your CD-ROM drive).
When the autorun screen appears, click Install.
Getting Started
Note: It is recommended to write down the SSID and Security Key, followed by the login password on the provided CD holder.
18D-Link DHP-1565 User Manual
Section 3 - Conguration
Conguration (Router Mode)
This section will show you how to congure your new D-Link wireless router using the web-based conguration utility.
Web-based Conguration Utility
To access the conguration utility, open a web-browser such as Internet
Explorer and enter the IP address of the router (192.168.0.1).
Select Admin in the User Name eld. Leave the password blank by default.
If you get a Page Cannot be Displayed error, please refer to the
Troubleshooting section for assistance.
19D-Link DHP-1565 User Manual
Section 3 - Conguration
Internet
Setup
This section allows you to congure your Router’s Internet settings.
The Internet Connection Setup Wizard provides a quick
method for conguring your Internet settings. To start
the Internet Connection Setup Wizard, click the Internet
Connection Setup Wizard button. Refer to “Internet
Connection Setup Wizard” on page 20 for more information
on how to use the Internet Connection Setup Wizard.
Click the Manual Internet Connection Setup button if
you want to enter your Internet settings without running
the Internet Connection Setup Wizard. Refer to “Manual
Internet Connection Setup” on page 26 for more information
on how to congure your Internet settings manually.
Internet
Connection
Setup Wizard:
Manual
Internet
Connection
Option:
20D-Link DHP-1565 User Manual
Section 3 - Conguration
Internet Connection Setup Wizard
Click the Internet Connection Setup Wizard button to start the Internet
Connection Setup Wizard.
21D-Link DHP-1565 User Manual
Section 3 - Conguration
Create a new password and then click Next to continue.
The following window appears, summarizing the steps required to
complete the Internet Connection Setup Wizard:
Click Next to continue.
Select your time zone from the drop-down menu and then click Next to
continue.
22D-Link DHP-1565 User Manual
Section 3 - Conguration
Select the type of Internet connection you use and then click Next to
continue.
If you selected DHCP Connection (Dynamic IP Address), you may need to
enter the MAC address of the computer that was last connected directly
to your modem. If you are currently using that computer, click Clone Your
PC’s MAC Address and then click Next to continue.
The Host Name is optional but may be required by some ISPs. The default
host name is the device name of the router and may be changed.
23D-Link DHP-1565 User Manual
Section 3 - Conguration
If you selected PPPoE, enter your PPPoE username and password.
If your ISP requires you to enter a PPPoE service name, enter the service
name in the Service Name eld.
Select Static if your ISP assigned you the IP address, subnet mask, gateway,
and DNS server addresses.
Click Next to continue.
Note: Make sure to remove your PPPoE software from your computer. The
software is no longer needed and will not work through a router.
If you selected PPTP, enter your PPTP username and password.
Select Static if your ISP assigned you the IP address, subnet mask, gateway,
and PPTP server addresses.
Click Next to continue.
24D-Link DHP-1565 User Manual
Section 3 - Conguration
If you selected L2TP, enter your L2TP username and password.
Select Static if your ISP assigned you the IP address, subnet mask, gateway,
and L2TP server addresses.
Click Next to continue.
If you selected Static, enter your network settings supplied by your Internet
provider.
Click Next to continue.
25D-Link DHP-1565 User Manual
Section 3 - Conguration
Click Connect to save your settings.
The following window appears to indicate that the settings are being
saved. When the Router has nished saving all the changes, the Setup>
Internet window will open.
Close your browser window and reopen it to test your Internet connection.
It may take a few tries to initially connect to the Internet.
26D-Link DHP-1565 User Manual
Section 3 - Conguration
Manual Internet Connection Setup
Use the My Internet Connection is drop-down menu to
select the mode that the router should use to connect to
the Internet.
Advanced Domain Name System (DNS) Services enhances
your Internet performance by getting you the information
and web pages you are looking for faster and more reliably.
In addition, it improves your overall Internet experience
by correcting many common typo mistakes automatically,
taking you where you intended to go and saving you
valuable time.
Disclaimer: D-Link makes no warranty as to the availability,
reliability, functionality and operation of the Advanced
DNS service or its features.
Internet
Connection
Type:
Advanced
DNS Service:
Select Manual Internet Connection Setup to continue.
27D-Link DHP-1565 User Manual
Section 3 - Conguration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The DNS server information will be supplied by your ISP
(Internet Service Provider).
Maximum Transmission Unit - you may need to change the
MTU for optimal performance with your specic ISP. 1500
is the default MTU.
The default MAC Address is set to the Internet port’s
physical interface MAC address on the Broadband Router.
It is not recommended that you change the default MAC
address unless required by your ISP. You can use the Clone
Your PC’s MAC Address button to replace the Internet port’s
MAC address with the MAC address of your Ethernet card.
IP Address:
Subnet Mask:
Default
Gateway:
DNS Servers:
MTU:
MAC Address:
Manual Internet Connection Setup
Static IP
Select Static IP from the drop-down menu if all the Internet port’s IP information is provided to you by your ISP. You will need
to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address
entered in the elds must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not
accept the IP address if it is not in this format.
Click the Save Settings button to save any changes made.
28D-Link DHP-1565 User Manual
Section 3 - Conguration
The Host Name is optional but may be required by some
ISPs. Leave blank if you are not sure.
Enter the Primary and Secondary DNS server IP addresses
assigned by your ISP. These addresses are usually obtained
automatically from your ISP. Enter the value 0.0.0.0 if you
did not specically receive these from your ISP.
Maximum Transmission Unit - you may need to change the
MTU for optimal performance with your specic ISP. 1500
is the default MTU.
The default MAC Address is set to the Internet port’s physical
interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address
unless required by your ISP. You can use the Clone Your
PC’s MAC Address button to replace the Internet port’s
MAC address with the MAC address of your Ethernet card.
Manual Internet Connection Setup
Dynamic IP (DHCP)
Select Dynamic IP (DHCP) from the drop-down menu to obtain IP Address information automatically from your ISP. Select
this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such
as Comcast and Cox.
Host Name:
Primary/
Secondary
DNS Server:
MTU:
MAC Address:
Click the Save Settings button to save any changes made.
29D-Link DHP-1565 User Manual
Section 3 - Conguration
Select Static IP if your ISP assigned you the IP address,
subnet mask, gateway, and DNS server addresses. In most
cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password
in the next box.
Enter the ISP Service Name (optional).
Use the radio buttons to specify the reconnect mode.
The user can specify a custom schedule or specify the On
Demand, or Manual option.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Enter the Primary and Secondary DNS Server Addresses
(Static PPPoE only).
Maximum Transmission Unit - you may need to change the
MTU for optimal performance with your specic ISP. 1492
is the default MTU.
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnect
Mode:
Maximum Idle
Time:
DNS Servers:
MTU:
Manual Internet Connection Setup
PPPoE (Username/Password)
Select PPPoE (Username/Password) from the drop-down menu if your ISP uses a PPPoE connection. Your ISP will provide you
with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from
your computer. The software is no longer needed and will not work through a router.
30D-Link DHP-1565 User Manual
Section 3 - Conguration
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
MAC Address:
Click the Save Settings button to save any changes made.
31D-Link DHP-1565 User Manual
Section 3 - Conguration
Select Static IP if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic IP.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses (Static
PPTP only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password in the
next box.
Use the radio buttons to specify the reconnect mode. The user can
specify a custom schedule or specify the On Demand, or Manual
option.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable Auto-reconnect.
Address Mode:
PPTP IP
Address:
PPTP Subnet
Mask:
PPTP Gateway
IP Address:
PPTP Server IP
Address:
Manual Internet Connection Setup
PPTP
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
Select PPTP (Point-to-Point Tunneling Protocol) from the drop-down menu if your ISP uses a PPTP connection. Your ISP will
provide you with a username and password. This option is typically used for DSL services.
32D-Link DHP-1565 User Manual
Section 3 - Conguration
The DNS server information will be supplied by your ISP (Internet Service Provider).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1454 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
DNS Servers:
MTU:
MAC Address:
Click the Save Settings button to save any changes made.
33D-Link DHP-1565 User Manual
Section 3 - Conguration
Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases,
select Dynamic.
Enter the L2TP IP address supplied by your ISP (Static only).
Enter the Subnet Mask supplied by your ISP (Static only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your L2TP username.
Enter your L2TP password and then retype the password in
the next box.
Use the radio buttons to specify the reconnect mode. The user
can specify a custom schedule or specify the On Demand, or
Manual option.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Address Mode:
L2TP IP Address:
L2TP Subnet
Mask:
Manual Internet Connection Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option
is typically used for DSL services.
L2TP Gateway
IP Address:
L2TP Server IP
Address:
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
34D-Link DHP-1565 User Manual
Section 3 - Conguration
Primary DNS
Server:
MTU:
MAC Address:
Enter the Primary DNS server IP address assigned by your ISP. These address is usually obtained automatically from your ISP. Enter
the value 0.0.0.0 if you did not specically receive these from your ISP.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1454 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
35D-Link DHP-1565 User Manual
Section 3 - Conguration
Manual Internet Connection Setup
DS-Lite
My Internet
Connection:
DS-Lite
Conguration:
AFTR IPV6
Address:
B4 IPv6
Address:
WAN IPv6
Address:
IPv6 WAN
Default
Gateway:
Select DS-Lite to activate this feature.
Select the DS-Lite DHCPv6 option to let the router
allocate the AFTR IPv6 address automatically. Select the
Manual Conguration to enter the AFTR IPv6 address in
manually.
After selecting the Manual Conguration option above,
enter the AFTR IPv6 address used here.
Enter the B4 IPv4 address value used here.
Once connected, the WAN IPv6 address will be displayed
here.
Once connected, the IPv6 WAN Default Gateway address
will be displayed here.
36D-Link DHP-1565 User Manual
Section 3 - Conguration
Wireless Settings
If you want to congure the wireless settings on your router using the
wizard, click Wireless Connection Setup Wizard and refer to “Wireless
Connection Setup Wizard” on page 101.
Click Add Wireless Device with WPS if you want to add a wireless device
using Wi-Fi Protected Setup (WPS) and refer to “Add Wireless Device with
WPS Wizard” on page 104.
If you want to manually congure the wireless settings on your router click
Manual Wireless Connection Setup and refer to the next page.
37D-Link DHP-1565 User Manual
Section 3 - Conguration
Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.
Select the time frame that you would like your wireless
network enabled. The schedule may be set to Always. Any
schedule you create will be available in the drop-down
menu. Click New Schedule to create a new schedule.
The Service Set Identier (SSID) is the name of your wireless
network. Create a name using up to 32 characters. The
SSID is case-sensitive.
Select one of the following:
802.11g Only - Select if all of your wireless clients are
802.11g.
802.11n Only - Select only if all of your wireless clients are
802.11n.
802.11b Only - Select if all of your wireless clients are
802.11b.
Mixed 802.11n and 802.11g - Select if you are using a mix
of 802.11n and 802.11g wireless clients.
Mixed 802.11g and 802.11b - Select if you are using a mix of 802.11g and 802.11b wireless clients.
Mixed 802.11n, 802.11g and 802.11b - Select 802.11n, 802.11g and 802.11b
The Auto Channel Selection setting can be selected to allow the DHP-1565 to choose the channel with the least amount of
interference.
Indicates the channel setting for the DHP-1565. By default the channel is set to 1. The Channel can be changed to t the channel
setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Selection, this option
will be greyed out.
Enable
Wireless:
Schedule:
Wireless
Network
Name:
802.11 Mode:
Enable Auto
Channel
Selection:
Wireless
Channel:
Manual Wireless Settings
802.11n/b/g (2.4GHz)
38D-Link DHP-1565 User Manual
Section 3 - Conguration
Channel
Width:
Wireless
Security
Mode:
Click the Save Settings button to save any changes made.
Select the Channel Width:
Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients. This is the default setting.
Refer to “Wireless Security” on page 136 for more information regarding wireless security.
39D-Link DHP-1565 User Manual
Section 3 - Conguration
This section will allow you to change the local network settings of the router and to congure the DHCP settings.
Network Settings
Use this section to congure the Router’s local network
settings.
Use this section to congure the DHP-1565’s built-in DHCP
server settings.
Use this section to create a new DHCP reservation or
manage existing DHCP reservations.
Displays information about the devices that have a DHCP
reservation from the DHP-1565. The information includes
the Host Name, IP Address, MAC Address, and Expiration
Time.
Displays information about the devices that have a
dynamic DHCP lease from the DHP-1565. The information
includes the Host Name, IP Address, MAC Address, and Lease
Expiration Time.
Router
Settings:
DHCP Server
Settings:
Add DHCP
Reservation:
DHCP
Reservations
List:
Number of
Dynamic
DHCP Clients:
40D-Link DHP-1565 User Manual
Section 3 - Conguration
Network Settings
Enter the IP address of the router. The default IP address
is 192.168.0.1.
If you change the IP address, once you click Apply, you
will need to enter the new IP address in your browser to
get back into the conguration utility.
Enter the Subnet Mask. The default subnet mask is
255.255.255.0.
Enter a Host Name to identify the DHP-1565.
Enter the Domain name (Optional).
Uncheck the box to transfer the DNS server information
from your ISP to your computers. If checked, your
computers will use the router for a DNS server.
Router IP
Address:
Default Subnet
Mask:
Device Name:
Local Domain:
Enable DNS
Relay:
Router Settings
Click the Save Settings button to save any changes made.
41D-Link DHP-1565 User Manual
Section 3 - Conguration
DHCP stands for Dynamic Host Control Protocol. The DHP-1565 has a built-in DHCP server. The DHCP Server will automatically assign an IP address
to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP
Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DHP-1565. The
DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting
and ending address of the IP address pool.
Check this box to enable the DHCP server on your router.
Uncheck to disable this function.
Enter the starting and ending IP addresses for the DHCP server’s
IP assignment.
Note: If you statically (manually) assign IP addresses to your
computers or devices, make sure the IP addresses are outside of
this range or you may have an IP conict.
The length of time for the IP address lease. Enter the Lease time
in minutes.
If NetBIOS advertisement is switched on, switching this setting
on causes WINS information to be learned from the WAN side,
if available. Turn this setting o to congure manually.
This is an advance setting and is normally left blank. This allows the conguration of NetBIOS domain name under which network
hosts operate. This setting has no eect if the “ Learn NetBIOS information form WAN is activated.
Enable DHCP
Server:
DHCP IP
Address
Range:
DHCP Lease
Time:
Learn NetBIOS
WAN:
NetBIOS scope:
Network Settings
DHCP Server Settings
When you have nished conguring the new DHCP Server Settings, click the Save Settings button at the top or bottom of the window.
42D-Link DHP-1565 User Manual
Section 3 - Conguration
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP
address only to that computer or device.
Note: This IP address must be within the DHCP IP Address Range.
Check this box to enable the reservation.
Enter the computer name. Alternatively, select a
computer that currently has a DHCP lease from the drop
down menu and click << to automatically populate the
Computer Name, IP Address, and MAC Address elds.
Enter the IP address you want to assign to the computer
or device. This IP Address must be within the DHCP IP
Address Range.
Enter the MAC address of the computer or device.
If you want to assign an IP address to the computer you
are currently on, click this button to populate the elds.
Click Save to save your entry. You must click Save
Settings at the top to activate your reservations.
In this section you can see what LAN devices are currently leasing IP addresses.
Enable:
Computer
Name:
IP Address:
MAC Address:
Copy Your PC’s
MAC Address:
Save:
Dynamic DHCP
Clients:
Network Settings
DHCP Reservation
When you have nished conguring the new DHCP Reservation, click the Save Settings button at the top or bottom of the window to activate
your reservations.
43D-Link DHP-1565 User Manual
Section 3 - Conguration
IPv6
On this page, the user can congure the IPv6 Connection type. There are two ways to set up the IPv6 Internet connection. You can use the Webbased
IPv6 Internet Connection Setup Wizard, or you can manually congure the connection.
IPv6 Internet Connection Setup Wizard
For the beginner user that has not congured a router before, click
on the IPv6 Internet Connection Setup Wizard button and the router
will guide you through a few simple steps to get your network up and
running.
Manual IPv6 Internet Connection Option
For the advanced user that has congured a router before, click on
the Manual IPv6 Internet Connection Setup button to input all the
settings manually.
44D-Link DHP-1565 User Manual
Section 3 - Conguration
Click the IPv6 Internet Connection Setup Wizard button and the router
will guide you through a few simple steps to get your network up and
running.
The router will try to detect whether its possible to obtain the IPv6
Internet connection type automatically. If this succeeds then the user
will be guided through the input of the appropriate parameters for the
connection type found.
Welcome to the D-Link IPv6 Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to congure
your newD-Link router and connect to the IPv6 Internet.
Click Next to continue to the next page. Click Cancel to discard the
changes made and return to the main page.
45D-Link DHP-1565 User Manual
Section 3 - Conguration
However, if the automatic detection fails, the user will be prompt to
either Try again or to click on the Guide me through the IPv6 settings
button to initiate the manual continual of the wizard.
There are several connection types to choose from. If you are unsure
of your connection method, please contact your IPv6 Internet Service
Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE
client software on your computers has been removed or disabled. The 3
options available on this page are IPv6 over PPPoE, Static IPv6 address
and Route, and Tunneling Connection.
Choose the required IPv6 Internet Connection type and click on the
Next button to continue. Click on the Prev button to return to the
previous page. Click on the Cancel button to discard all the changes
made and return to the main page.
46D-Link DHP-1565 User Manual
Section 3 - Conguration
After selecting the IPv6 over PPPoE option, the user will be able to
congure the IPv6 Internet connection that requires a username and
password to get online. Most DSL modems use this type of connection.
The following parameters will be available for conguration:
PPPoE Session:
Username:
Password:
Verify Password:
Service Name:
Select the PPPoE Session value used here. This option
will state that this connection shares it’s information
with the already congured IPv6 PPPoE connection,
or the user can create a new PPPoE connection here.
Enter the PPPoE username used here. If you do not
know your user name, please contact your ISP.
Enter the PPPoE password used here. If you do not
know your password, please contact your ISP.
Re-enter the PPPoE password used here.
Enter the service name for this connection here. This
option is optional.
Click on the Next button to continue. Click on the
Prev button to return to the previous page.
Click on the Cancel button to discard all the changes
made and return to the main page.
IPv6
IPv6 over PPPoE
47D-Link DHP-1565 User Manual
Section 3 - Conguration
This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your
IPv6 conguration settings. You must enter the IPv6 address, Subnet Prex Length, Default Gateway, Primary DNS Server, and Secondary DNS
Server. Your ISP provides you with all this information.
Use Link-Local
Address:
IPv6 Address:
Subnet Prex
Length:
Default
Gateway:
Primary IPv6
DNS Address:
Secondary IPv6
DNS Address:
LAN IPv6
Address:
The Link-local address is used by nodes and routers
when communicating with neighboring nodes on the
same link. This mode enables IPv6- capable devices to
communicate with each other on the LAN side.
Enter the WAN IPv6 address for the router here.
Enter the WAN subnet prex length value used here.
Enter the WAN default gateway IPv6 address used here.
Enter the WAN primary DNS Server address used here.
Enter the WAN secondary DNS Server address used here.
These are the settings of the LAN (Local Area Network) IPv6 interface for the router. The router’s LAN IPv6 Address conguration is
based on the IPv6 Address and Subnet assigned by your ISP. (A subnet with prex /64 is supported in LAN.)
Click on the Next button to continue. Click on the Prev button to return to the previous page.
Click on the Cancel button to discard all the changes made and return to the main page.
IPv6
Static IPv6
48D-Link DHP-1565 User Manual
Section 3 - Conguration
After selecting the Tunneling Connection (6rd) option, the user can congure the IPv6 6rd connection settings.
The following parameters will be available for conguration:
6rd IPv6 Prex:
IPv4 Address:
Assigned IPv6
Prex:
6rd Border Relay
IPv4 Address:
IPv6 DNS Server:
Enter the 6rd IPv6 address and prex value used here.
Enter the IPv4 address used here.
Displays the IPv6 assigned prex value here.
Enter the 6rd border relay IPv4 address used here.
Enter the primary DNS Server address used here.
Click on the Next button to continue. Click on the Prev button to return to the previous page.
Click on the Cancel button to discard all the changes made and return to the main page.
The IPv6 Internet Connection Setup Wizard was completed.
Click on the Connect button to continue. Click on the Prev button to
return to the previous page.
Click on the Cancel button to discard all the changes made and return
to the main page.
IPv6
Tunneling Connection (6rd)
49D-Link DHP-1565 User Manual
Section 3 - Conguration
Displays the LAN IPv6 Link-Local address of the
router.
LAN IPv6 Address
Settings:
IPv6
Link-local Only
Select Link-local Only from the My IPv6 Connection is drop-down
menu if your Router will use the IPv6 link local method to connect to
the Internet.
Click the Save Settings button to save any changes made.
50D-Link DHP-1565 User Manual
Section 3 - Conguration
There are several connection types to choose from: Auto Detection, Static IPv6, Autoconguration (SLAAC/DHCPv6), PPPoE, IPv6 in IPv4 Tunnel,
6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled.
IPv6 Manual Setup
Auto Detection
Select Auto Detection to have the router detect and automatically
congure your IPv6 setting from your ISP.
Click Manual IPv6 Internet Connection Setup to begin.
51D-Link DHP-1565 User Manual
Section 3 - Conguration
Static IPv6
Select Static IPv6 from the drop-down menu.
Enter the address settings supplied by your Internet provider (ISP).
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconguration feature.
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
WAN IPv6 Address Settings:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconguration:
Autoconguration Type:
IPv6 Address Range Start:
IPv6 Address Range End:
IPv6 Address Lifetime:
52D-Link DHP-1565 User Manual
Section 3 - Conguration
Autoconguration
Select Autoconguration (Stateless/DHCPv6) from the drop-down menu.
Select either Obtain DNS server address automatically or Use the following
DNS Address.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconguration feature.
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
IPv6 DNS Settings:
Primary/Secondary DNS
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconguration:
Autoconguration Type:
IPv6 Address Range Start:
IPv6 Address Range End:
IPv6 Address Lifetime:
53D-Link DHP-1565 User Manual
Section 3 - Conguration
PPPoE
Select PPPoE from the drop-down menu.
Enter the PPPoE account settings supplied by your Internet provider (ISP).
Select Static if your ISP assigned you the IP address, subnet mask, gateway,
and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next box.
Enter the ISP Service Name (optional).
Select either Always-on, On-Demand, or Manual.
Enter a maximum idle time during which the Internet connection is
maintained during inactivity. To disable this feature, enable Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal
performance with your specic ISP. 1492 is the default MTU.
Select either Obtain DNS server address automatically or Use the
following DNS Address.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconguration feature.
My IPv6 Connection:
PPPoE:
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnection Mode:
Maximum Idle Time:
MTU:
IPv6 DNS Settings:
Primary/Secondary DNS
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconguration:
54D-Link DHP-1565 User Manual
Section 3 - Conguration
Autoconguration Type:
IPv6 Address Range Start:
IPv6 Address Range End:
IPv6 Address Lifetime:
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).
55D-Link DHP-1565 User Manual
Section 3 - Conguration
IPv6 in IPv4 Tunneling
Select IPv6 in IPv4 Tunnel from the drop-down menu.
Enter the settings supplied by your Internet provider (ISP).
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconguration feature.
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the Router Advertisement Lifetime (in minutes).
My IPv6 Connection:
IPv6 in IPv4 Tunnel
Settings:
LAN IPv6 Address:
LAN Link-Local
Address:
Enable
Autoconguration:
Autoconguration
Type:
IPv6 Address Range
Start:
IPv6 Address Range
End:
Pv6 Address Lifetime:
56D-Link DHP-1565 User Manual
Section 3 - Conguration
6 to 4 Tunneling
Select 6 to 4 from the drop-down menu.
Enter the IPv6 settings supplied by your Internet provider (ISP).
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconguration feature.
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6 Connection:
6 to 4 Settings:
Primary/Secondary DNS
Address:
LAN IPv6 Address:
LAN Link-Local Address:
Enable
Autoconguration:
Autoconguration Type:
IPv6 Address Range
Start:
IPv6 Address Range
End:
IPv6 Address Lifetime:
57D-Link DHP-1565 User Manual
Section 3 - Conguration
6rd
Select 6rd from the drop-down menu.
Enter the address settings supplied by your Internet provider (ISP).
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconguration feature.
Select Stateful (DHCPv6), SLAAC+RDNSS or SLAAC + Stateless DHCPv6.
Enter the Router Advertisement Lifetime (in minutes).
My IPv6 Connection:
6RD Settings:
LAN IPv6 Address:
LAN Link-Local Address:
Enable Autoconguration:
Autoconguration Type:
Router Advertisement
Lifetime:
58D-Link DHP-1565 User Manual
Section 3 - Conguration
This section will show you how to congure your new D-Link PowerLine AV using the web-based conguration utility.
PLC Settings (Router Mode)
59D-Link DHP-1565 User Manual
Section 3 - Conguration
Network
Name:
Public
Network
Name:
Private
Network
Name:
Scan:
Add Member:
Device Name:
Password:
You can set the name of your network and to make it
either public or private. Make sure the Network Name of
all of the devices within your PowerLine network is the
same.
Select this option if you would like to make your powerline
network public with the default Network Name of
“HomePlugAV”. Since this is a commonly used Network
Name, it is less secure than a private Network Name.
Select this option if you wish to make your powerline
network more secure by using a private Network Name.
Type the name of your private PowerLine network in the
eld.
Scan for new PowerLine devices.
This section lets you add new PowerLine AV devices to
your PowerLine network. To add a new device, give it a
Device Name and enter its Password, then click Add. When
you add a device it is given the current Network Name.
Type a name you wish to use to identify a specific
PowerLine AV device. For example, “Jack’s room”.
The Password is used to verify that you are authorized to
perform changes on a device. You can
nd the Password printed on the back of your device.
60D-Link DHP-1565 User Manual
Section 3 - Conguration
Member List:
Link Rate:
This section provides information on the PowerLine
AV devices in your PowerLine network, or any devices
that were previously connected but it are currently
disconnected.
Displays the device’s current data rate in Mbps.
Status:
Qos Settings:
Mac Address:
This field shows the status of the device. If the field
displays the word Connect, then the device is connected
to your PowerLine network. If the eld displays the word
Disconnect, then the device has been added to the network
but it is not ready. Please check its password and make sure
the device is powered on.
You can configure your PowerLine AV devices to give
priority to powerline network trac accordingly. Enter the
name, MAC Address, and priority level.
You can nd the MAC address printed on the back of your
device.
61D-Link DHP-1565 User Manual
Section 3 - Conguration
The DHP-1565 can be congured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically
redirected to local servers in the LAN (Local Area Network).
The DHP-1565 rewall feature lters out unrecognized packets to protect your LAN network so all computers networked with the DHP-1565
are invisible to the outside world. If you wish, you can make some of the LAN computers accessible from the Internet by enabling Virtual Server.
Depending on the requested service, the DHP-1565 redirects the external service request to the appropriate server within the LAN network.
The DHP-1565 is also capable of port-redirection, meaning that incoming trac to a particular port may be redirected to a dierent port on the
server computer.
For a list of ports for common applications, please visit http://support.dlink.com/faq.
Virtual Server
Advanced
62D-Link DHP-1565 User Manual
Section 3 - Conguration
The Virtual Server window allows you to open a single port. If you would like to open a range of ports, refer to the next page.
Check the box on the left side to enable the Virtual
Server rule.
Enter a name for the rule or select an application from
the drop-down menu. Select an application and click
<< to populate the elds.
Enter the IP address of the computer on your local
network that you want to allow the incoming service to.
If your computer is receiving an IP address automatically
from the router (DHCP), you computer will be listed in
the Computer Name drop-down menu. Select your
computer and click <<.
Enter the port that you want to open next to Public
Port and Private Port. The public and private ports are
usually the same. The public port is the port seen from
the Internet side, and the private port is the port being
used by the application on the computer within your
local network.
Select TCP, UDP, Both or other from the Protocol drop-
down menu.
Use the drop-down menu to schedule the time that the Virtual Server Rule will be enabled. The schedule may be set to Always,
which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.
Select Allow All (most common) or a created Inbound lter. You may create your own inbound lters in the Advanced > Inbound
Filter page.
Enable
Checkbox:
Name:
IP Address:
Public Port/
Private Port:
Trac Type:
Schedule
Drop-Down
Menu:
Inbound Filter:
Click the Save Settings button to save any changes made.
63D-Link DHP-1565 User Manual
Section 3 - Conguration
This will allow you to open a single port or a range of ports.
Port Forwarding
Tick the checkbox on the left side to enable the Port
Forwarding rule.
Enter a name for the rule or select an application
from the drop-down menu. Select an application
and click << to populate the elds.
Enter the IP address of the computer on your local
network that you want to allow the incoming service
to. If your computer is receiving an IP address
automatically from the router (DHCP), you computer
will be listed in the Computer Name drop-down
menu. Select your computer and click <<.
Enter the port that you want to open next to TCP
Port and UDP Port.
Use the drop-down menu to schedule the time
that the Port Forwarding rule will be enabled. The
schedule may be set to Always, which will allow
the particular service to always be enabled. You can
create your own times in the Tools > Schedules
section.
Select Allow All (most common) or a created
Inbound lter. You may create your own inbound
lters in the Advanced > Inbound Filter page.
Enable
Checkbox:
Name:
IP Address:
TCP Port/
UDP Port:
Schedule:
Inbound Filter:
Click the Save Settings button to save any changes made.
64D-Link DHP-1565 User Manual
Section 3 - Conguration
Check the box on the left side to enable the Application
Rule.
Enter a name for the rule. You may select a pre-dened
application from the Application drop-down menu and
click <<.
This is the port used to trigger the application. It can be
either a single port or a range of ports.
Select the protocol of the trigger port (TCP, UDP, or Any).
This is the port number on the Internet side that will be
used to access the application. You may dene a single port
or a range of ports. You can use a comma to add multiple
ports or port ranges.
Select the protocol of the rewall port (TCP or UDP).
The schedule of time when the Application Rule will be
enabled. The schedule may be set to Always, which will
allow the particular service to always be enabled. You can
create your own times in the Tools > Schedules section.
Enable
Checkbox:
Name:
Trigger:
Trac Type:
Firewall:
Trac Type:
Schedule:
Application Rules
Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications
have diculties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DHP-
1565. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port”
eld, select the protocol type as TCP or UDP, then enter the rewall (public) ports associated with the trigger port to open them for inbound trac.
Click the Save Settings button to save any changes made.
65D-Link DHP-1565 User Manual
Section 3 - Conguration
QoS Engine
This option is disabled by default. Enable this option
for better performance and experience with online
games and other interactive applications, such as VoIP.
This option is enabled by default when the QoS Engine
option is enabled. This option will allow your router
to automatically determine the uplink speed of your
Internet connection.
This displays the detected uplink speed.
The speed at which data can be transferred from the
router to your ISP. This is determined by your ISP. ISP’s
often dene speed as a download/upload pair. For
example, 1.5Mbits/284Kbits. Using this example, you
would enter 284. Alternatively you can test your uplink
speed with a service such as www.dslreports.com.
This option is enabled by default. This will allow your
router to automatically determine the network priority
of running programs.
This option is enabled by default so that your router will
automatically determine which programs should have
network priority. For best performance, use the Automatic Classication option to automatically set the priority for your applications.
This option should be enabled when you have a slow Internet uplink. It helps to reduce the impact that large low priority network
packets can have on more urgent ones.
Enable Trac
Shaping:
Automatic
Uplink Speed:
Measured
Uplink Speed:
Manual Uplink
Speed:
Enabled QoS
Engine:
Automatic
Classication:
Dynamic
Fragmentation:
The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are
disabled and application priority is not classied automatically.
66D-Link DHP-1565 User Manual
Section 3 - Conguration
A QoS Engine Rule identies a specic message ow
and assigns a priority to that ow. For most applications,
automatic classication will be adequate, and specic
QoS Engine Rules will not be required.
The QoS Engine supports overlaps between rules, where
more than one rule can match for a specic message
ow. If more than one rule is found to match the rule
with the highest priority will be used.
Create a name for the rule that is meaningful to you.
The priority of the message ow is entered here -- 1
receives the highest priority (most urgent) and 255
receives the lowest priority (least urgent).
The protocol used by the messages.
The rule applies to a ow of messages whose LAN-side
IP address falls within the range set here.
The rule applies to a ow of messages whose LAN-side
port number is within the range set here.
The rule applies to a ow of messages whose WAN-side
IP address falls within the range set here.
The rule applies to a ow of messages whose WAN-side
port number is within the range set here.
QoS Engine Rules:
Name:
Priority:
Protocol:
Local IP Range:
Local Port Range:
Remote IP Range:
Remote Port Range:
67D-Link DHP-1565 User Manual
Section 3 - Conguration
Network Filter
Select Turn MAC Filtering OFF, Turn MAC Filtering ON
and ALLOW computers listed to access the network, or
Turn MAC Filtering ON and DENY computers listed to
access the network from the drop-down menu.
Enter the MAC address you would like to lter.
To nd the MAC address on a computer, please refer to
the Networking Basics section in this manual.
Select a DHCP client from the Computer Name drop
down menu and click << to copy that MAC Address.
Congure MAC
Filtering:
MAC Address:
DHCP Client
List:
Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the network.
You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.
Click the Save Settings button to save any changes made.
68D-Link DHP-1565 User Manual
Section 3 - Conguration
Access Control
Check the Enable Access Control check box and
click the Add Policy button to start the Access
Control Wizard.
Add Policy:
The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to
approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games.
Click Next to continue with the wizard.
Access Control Wizard
69D-Link DHP-1565 User Manual
Section 3 - Conguration
Enter a name for the policy and then click Next to continue.
Select a schedule (I.E. Always) from the drop-down menu and
then click Next to continue.
Enter the following information and then click Next to continue.
• Address Type - Select IP address, MAC address, or Other Machines.
• IP Address - Enter the IP address of the computer you want to apply
the rule to.
Select the ltering method and then click Next to continue.
70D-Link DHP-1565 User Manual
Section 3 - Conguration
Enter the rule:
Enable - Check to enable the rule.
Name - Enter a name for your rule.
Dest IP Start - Enter the starting IP address.
Dest IP End - Enter the ending IP address.
Protocol - Select the protocol.
Dest Port Start - Enter the starting port number.
Dest Port End - Enter the ending port number.
To enable web logging, click Enable.
Click Save to save the access control rule.
Once your changes have been saved, you can select Reboot Now or
Reboot Later.
71D-Link DHP-1565 User Manual
Section 3 - Conguration
Congure Web
Filtering:
Website URL:
Website Filter
Select ALLOW computers access to ONLY these sites, or
DENY computers access to ONLY these sites from the
drop-down menu.
Enter the keywords or URLs that you want to allow or block.
Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select
the appropriate Web Filtering option, enter the domain or website, and click Save Settings.
Click the Save Settings button to save any changes made.
72D-Link DHP-1565 User Manual
Section 3 - Conguration
Inbound Filter
Enter a name for the inbound lter rule.
Select Allow or Deny.
Check to enable rule.
Enter the starting IP address. Enter 0.0.0.0 if you
do not want to specify an IP range.
Enter the ending IP address. Enter 255.255.255.255
if you do not want to specify and IP range.
Click the Add button to apply your settings.
Name:
Action:
Enable:
Remote IP
Start:
Remote IP End:
Add:
The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can congure inbound
data ltering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote
Administration features.
73D-Link DHP-1565 User Manual
Section 3 - Conguration
Check the Enable SPI box to enable the SPI (Stateful
Packet Inspection, also known as dynamic packet ltering)
feature. Enabling SPI helps to prevent cyber attacks by
tracking more state per session. It validates that the trac
passing through the session conforms to the protocol.
Select one of the following for TCP and UDP ports:
Endpoint Independent - Any incoming trac sent to
an open port will be forwarded to the application that
opened the port. The port will close if idle for 5 minutes.
Address Restricted - Incoming trac must match the IP
address of the outgoing connection.
Address + Port Restriction - Incoming trac must match
the IP address and port of the outgoing connection.
Enable this option to provide protection from certain kinds
of “spoong” attacks.
Firewall
Settings:
NAT Endpoint
Filtering:
Enable
Anti-Spoof
Checking:
Firewall Settings
A rewall protects your network from the outside world. The DHP-1565 oers a rewall type functionality. The SPI feature helps prevent cyber
attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer,
you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
74D-Link DHP-1565 User Manual
Section 3 - Conguration
1. Check the Enable DMZ box.
2. Specify the IP address of the computer on the
LAN that you want to have unrestricted Internet
communication in the DMZ IP address eld. To
specify an existing DHCP client, use the Computer
Name drop-down to select the computer that
you want to make a DMZ host. If selecting a
computer that is a DHCP client, be sure to make
a static reservation in the Setup > Network
Settings page so that the IP address of the DMZ
machine does not change.
3. Click the Save Settings button to add the new
DMZ host.
DMZ Host:
IP Address:
If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application
on that computer.
Carry out the following to create a DMZ host:
Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer
obtains its IP address automatically using DHCP, be sure to make a static reservation on the System > Network Settings page so
that the IP address of the DMZ machine does not change.
Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as
a last resort.
75D-Link DHP-1565 User Manual
Section 3 - Conguration
Routing
The Routing option is an advanced method of customizing specic routes of data through your network.
Click the Save Settings button to save any changes made.
Routing List:
Name:
Interface:
Destination IP:
Netmask:
Gateway:
Each Route has a checkbox next to it, check the box
of the route you wish to enable.
Specify a name for identication of this route.
Select the interface which the IP packet must use to
transit out of the router when this route is used.
Enter the address of the host or network you wish
to access.
This eld identies the portion of the destination IP
in use.
The IP address of the router will be displayed here.
76D-Link DHP-1565 User Manual
Section 3 - Conguration
Set the transmit power of the antennas.
Beacons are packets sent by an Access Point to
synchronize a wireless network. Specify a value. 100 is
the default setting and is recommended.
This value should remain at its default setting of 2346.
If inconsistent data flow is a problem, only a minor
modication should be made.
(Delivery Trac Indication Message) 1 is the default
setting. A DTIM is a countdown informing clients of the
next window for listening to broadcast and multicast
messages.
This enables 802.11d operation. 802.11d is a wireless specication developed to allow implementation of wireless networks in
countries that cannot use the 802.11 standard. This feature should only be enabled if you are in a country that requires it.
WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.
Transmit Power:
Beacon Period:
RTS Threshold:
DTIM Interval:
WLAN Partition:
WMM Enable:
Advanced Wireless Settings
802.11n/b/g (2.4GHz)
Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create
higher data loss.
Short Guard
Interval:
Click the Save Settings button to save any changes made.
77D-Link DHP-1565 User Manual
Section 3 - Conguration
Wi-Fi Protected Setup (WPS)
Enable the Wi-Fi Protected Setup feature.
A PIN is a unique number that can be used to add the
router to an existing network or to create a new network.
The default PIN may be printed on the bottom of the
router. For extra security, a new PIN can be generated.
You can restore the default PIN at any time. Only the
Administrator (“admin” account) can change or reset
the PIN.
Shows the current value of the router’s PIN.
Click this button to restore the default PIN of the router.
Click this button to create a random number that is a
valid PIN. This becomes the router’s PIN. You can then
copy this PIN to the user interface of the registrar.
Enable:
PIN Settings:
PIN:
Reset PIN to
Default:
Generate New
PIN:
Wi-Fi Protected Setup (WPS) System is a simplied method for securing your wireless network during the “Initial setup” as well as the “Add New
Device” processes. The Wi-Fi Alliance (WFA) has certied it across dierent products as well as manufactures. The process is just as easy, as depressing
a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method. The time reduction in setup and ease of use
are quite benecial, while the highest wireless Security setting of WPA2 is automatically used.
78D-Link DHP-1565 User Manual
Section 3 - Conguration
Click the Add Wireless Device with WPS button to start Wireless Connection Setup Wizard. This wizard helps you add wireless
devices to the wireless network.
The wizard will either display the wireless network settings to guide you through manual conguration, prompt you to enter the
PIN for the device, or ask you to press the conguration button on the device. If the device supports Wi-Fi Protected Setup and has a
conguration button, you can add it to the network by pressing the conguration button on the device and then the on the router
within 60 seconds. The status LED on the router will ash three times if the device has been successfully added to the network.
There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A registrar
only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the
device. The router acts as a registrar for the network, although other devices may act as a registrar as well.
Add Wireless
Station:
Click the Save Settings button to save any changes made.
79D-Link DHP-1565 User Manual
Section 3 - Conguration
UPnP
Internet Ping Block
Internet Port Speed
Multicast Streams
To use the Universal Plug and Play (UPnP™) feature click on
Enabled. UPNP provides compatibility with networking
equipment, software and peripherals.
Unchecking the box will not allow the DHP-1565 to
respond to pings. Blocking the Ping may provide some
extra security from hackers. Check the box to allow the
Internet port to be “pinged”.
You may set the port speed of the Internet port to 10Mbps,
100Mbps, or auto. Some older cable or DSL modems may
require you to set the port speed to 10Mbps.
Check the Enable Multicast Streams box to allow multicast
trac to pass through the router from the Internet.
Enable UPnP:
Enable WAN
Ping Response:
WAN Port
Speed:
Enable
Multicast
Streams:
Advanced Network
Click the Save Settings button to save any changes made.
80D-Link DHP-1565 User Manual
Section 3 - Conguration
Guest Zone
Enable Guest Zone:
New Schedule:
Wireless Network
Name:
Enable Routing
Between Zones:
Security Mode:
The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate
from your main wireless network.
Check to enable the Guest Zone feature.
The schedule of time when the Guest Zone will
be active. The schedule may be set to Always,
which will allow the particular service to always be
enabled. You can create your own times in the Tools
> Schedules section.
Enter a wireless network name (SSID) that is dierent
from your main wireless network.
Check to allow network connectivity between the
dierent zones created.
Select the type of security or encryption you would
like toenable for the guest zone.
81D-Link DHP-1565 User Manual
Section 3 - Conguration
IPv6 Firewall
On this page the user can congure the IPv6 rewall settings. The rewall settings section is an advance feature that is used to allow or deny
trac from passing through the device. It works in the same way as IP Filters with additional settings. You can create more detailed rules for the
device.
Name:
Source Interface:
Destination
Interface:
Schedule:
IP Address Range:
Protocol:
Port Range:
Enter a custom rewall rule name here. This name is
used for identication.
Select the appropriate source interface used here.
Select the appropriate destination interface used
here.
Select a time schedule that will be applied to this rules
here.
Enter the IPv6 address range used here.
Select the protocol used for this rule here. Options to
choose from are ALL, TCP, UDP, and ICMP.
Enter the port range used for this rule here.
82D-Link DHP-1565 User Manual
Section 3 - Conguration
IPv6 Routing
This page allows you to specify custom routes that determine how data is moved around your network.
Routing List:
Name:
Destination IP:
Metric:
Interface:
Gateway:
Each Route has a checkbox next to it, check the box
of the route you wish to enable.
Specify a name for identication of this route.
This eld identies the portion of the destination IP
in use.
The route metric is a value from 1 to 16 that indicates
the cost of using this route. A value 1 is the lowest
cost and 15 is the highest cost.
Select the interface which the IP packet must use to
transit out of the router when this route is used.
The IP address of the router will be displayed here.
83D-Link DHP-1565 User Manual
Section 3 - Conguration
Enter a new password for the Administrator Login Name.
The administrator can make changes to the settings.
Enter the new password for the User login. If you login
as the User, you can only see the settings, but cannot
change them.
Enter a name for your DHP-1565 Router.
Enables a challenge-response test to require users to type
letters or numbers from a distorted image displayed on
the screen to prevent online hackers and unauthorized
users from gaining access to your router’s network
settings.
Remote management allows the DHP-1565 to be
configured from the Internet by a web browser. A
username and password is still required to access the Web-
Management interface. In general, only a member of your
network can browse the built-in web pages to perform
Administrator tasks. This feature enables you to perform
Administrator tasks from the remote (Internet) host.
Enter the port number that will be used to access the
DHP-1565.
Admin
Password:
Admin
This page will allow you to change the Administrator password and congure the authentication settings. This window also allows you to enable
Remote Management, via the Internet.
Tools
Enable
Graphical
Authentication:
Enable Remote
Management:
Remote
Admin Port:
Click the Save Settings button to save any changes made.
User Password:
Gateway Name:
84D-Link DHP-1565 User Manual
Section 3 - Conguration
Time
Select the Time Zone from the drop-down menu.
Check this box if the country your are located in uses
Daylight Saving time. Enter a start date and an end date
for daylight saving time.
Check this box to enable the NTP Server.
NTP is short for Network Time Protocol. NTP synchronizes
computer clock times in a network of computers. To enable
NTP carry out the following:
1. Check the Automatically synchronize with D-Link’s
Internet Time Server box.
2. Choose the D-Link NTP server that you would like to
synchronize with from the NTP Server Used drop-down
menu.
Use this section to configure the time manually. To
congure the time manually, use the drop-down menus
to select the appropriate Year, Month, Day, Hour, Minute,
and Second.
Time Zone:
Enable
Daylight
Saving:
Enable NTP
Server:
NTP Server
Used:
Set the Time
and Date
Manually:
The Time window allows you to congure, update, and maintain the correct time on the internal system clock. From this section you can set the
time zone that you are in and set the Time Server. Daylight Saving can also be congured to automatically adjust the time when needed.
Click the Save Settings button to save any changes made.
85D-Link DHP-1565 User Manual
Section 3 - Conguration
The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server on your
network.
Enable
Logging
to SysLog
Server:
SysLog Server
IP Address:
Check this box to send the router logs to a SysLog Server.
The address of the SysLog server that will be used to
send the logs. You may also select your computer from
the drop-down menu (only if receiving an IP address
from the router via DHCP).
SysLog
86D-Link DHP-1565 User Manual
Section 3 - Conguration
Email Settings
The Email feature can be used to send the system log les and router alert messages to your email address.
Enable Email
Notications:
From Email
Address:
To Email
Address:
SMTP Server
Address:
Enable
Authentication:
Account Name:
Password:
Send Mail Now:
On Log Full:
On Schedule:
Schedule:
When this option is enabled, router activity logs are e-mailed
to a designated e-mail address.
This e-mail address will appear as the sender when you receive
a log le or rmware upgrade notication via e-mail.
Enter the e-mail address where you want the e-mail sent.
Enter the SMTP server address for sending e-mail. If your SMTP
server requires authentication, select this option.
Check this box if your SMTP server requires authentication.
Enter your account for sending e-mail.
Enter the password associated with the account. Re-type the password associated with the account.
Click this button to send a test e-mail from the Router to verify that the e-mail settings have been congured correctly.
When this option is selected, logs will be sent via e-mail when the log is full.
Selecting this option will send the logs via e-mail according to schedule.
This option is enabled when On Schedule is selected. You can select a schedule from the list of dened schedules. To create
a schedule, go to Tools > Schedules.
Click the Save Settings button to save any changes made.
87D-Link DHP-1565 User Manual
Section 3 - Conguration
Use this option to save the current router conguration
settings to a le on the hard disk of the computer you
are using. First, click the Save button. A le dialog will
appear, allowing you to select a location and le name
for the settings.
Use this option to load previously saved router conguration
settings. First, use the Browse option to nd a previously
saved le of conguration settings. Then, click the Upload
Settings button below to transfer those settings to the
router.
This option will restore all conguration settings back
to the settings that were in eect at the time the router
was shipped from the factory. Any settings that have
not been saved will be lost, including any rules that
you have created. If you want to save the current router
conguration settings, use the Save button above.
Click to reboot the router.
Save Settings to
Local Hard Drive:
Load Settings
from Local Hard
Drive:
Restore to
Factory Default
Settings:
Reboot Device:
System
This section allows you to manage the router’s conguration settings, reboot the router, and restore the router to the factory default settings.
Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
88D-Link DHP-1565 User Manual
Section 3 - Conguration
This section displays information about the rmware
that is loaded on the Router. Click the Check Now
button to nd out if there is an updated rmware; if so,
download the new rmware to your hard drive.
After you have downloaded the new rmware, click
Browse to locate the rmware update on your hard
drive. Click Upload to complete the rmware upgrade.
Firmware
Information:
Firmware
Upgrade:
Firmware
Use the Firmware window to upgrade the rmware of the Router and install language packs. If you plan to install new rmware, make sure the
rmware you want to use is on the local hard drive of the computer. If you want to install a new language pack, make sure that you have the language
pack available. Please check the D-Link support site for rmware updates at http://support.dlink.com. You can download rmware upgrades to your
hard drive from the D-Link support site.
89D-Link DHP-1565 User Manual
Section 3 - Conguration
Dynamic Domain Name System is a method of
keeping a domain name linked to a changing IP
Address. Check the box to enable DDNS.
Choose your DDNS provider from the drop down
menu.
Enter the Host Name that you registered with your
DDNS service provider.
Enter the Username for your DDNS account.
Enter a time in (hours).
Displays the current connection status to your DDNS
server.
Enable DDNS:
Server Address:
Host Name:
Username or Key:
Timeout:
Status:
Dynamic DNS
The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.
com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS
service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Click the Save Settings button to save any changes made.
90D-Link DHP-1565 User Manual
Section 3 - Conguration
The Ping Test is used to send Ping packets to test if a
computer is on the Internet. Enter the IP Address that you
wish to Ping, and click Ping. Click Stop to stop sending
Ping packets
The IPv6 Ping Test is used to send IPv6 Ping packets to test
if a computer is on the Internet. Enter the IPv6 Address
that you wish to Ping, and click Ping. Click Stop to stop
sending IPv6 Ping packets
The results of your Ping/IPv6 Ping attempts will be
displayed here.
System Check
Ping Test:
IPv6 Ping
Test:
Ping Results:
91D-Link DHP-1565 User Manual
Section 3 - Conguration
Enter a name for your new schedule.
Select a day, a range of days, or All Week to include every
day.
Check All Day - 24hrs or enter a Start Time and End Time
for your schedule.
Click Save to save your schedule. You must click the Save
button for your schedules to go into eect.
The list of schedules will be listed here. Click the Edit icon
to make changes or click the Delete icon to remove the
schedule.
Name:
Days:
Time:
Save:
Schedule Rules
List:
Schedules
Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create
a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.
92D-Link DHP-1565 User Manual
Section 3 - Conguration
This page displays the current information for the DHP-1565. It will display the LAN, WAN (Internet), and Wireless information. If your Internet
connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your
ISP and use Renew to connect to your ISP.
If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE
connection and use Connect to establish the PPPoE connection.
Displays the router’s time and rmware version.
Displays the MAC address and the public IP settings for
the router.
Displays the MAC address and the private (local) IP settings
for the router.
Displays the wireless MAC address and your wireless
settings such as SSID and Channel.
Displays computers and other devices which are connected
to the router via Ethernet, and that are receiving an IP
address assigned by the router CDHCP).
Displays the Multicast Group IP address.
General:
WAN:
LAN:
Wireless LAN:
LAN Computer:
IGMP Multicast
Memberships:
Device Info
Status
93D-Link DHP-1565 User Manual
Section 3 - Conguration
Logs
Save Log File:
Log Type:
First Page:
Last Page:
Previous:
Next:
Clear:
Email Now:
Click the Apply Log Settings Now button save the Router’s
log entries to a log le on your computer.
Use the radio buttons to select the types of messages
that you want to display from the log. System, Firewall
& Security, and Router Status messages can be selected.
Click this button to view the rst page of the Router logs.
Click this button to view the last page of the Router logs.
Click this button to view the previous page of the Router
logs.
Click this button to view the next page of the Router logs.
Clears all of the log contents.
Click this button to open the Tools > Email Settings
screen so that you can change the Email conguration
for sending logs.
The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs
of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can dene what types
of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log les to
a computer on your network that is running a Syslog utility.
94D-Link DHP-1565 User Manual
Section 3 - Conguration
Statistics
The screen below displays the Trac Statistics. Here you can view the amount of packets that pass through the DHP-1565 on both the WAN, LAN ports
and the 802.11n/g (2.4GHz) wireless band. The trac counter will reset if the device is rebooted.
Refresh:
Reset:
Click the Refresh button to refresh the Router’s trac
statistics.
Click the Reset button to reset the Router’s trac
statistics.
95D-Link DHP-1565 User Manual
Section 3 - Conguration
Internet Sessions
The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a
program or application on a LAN-side computer and a program or application on a WAN-side computer.
96D-Link DHP-1565 User Manual
Section 3 - Conguration
Routing Table
This page displays the routing details congured for your router.
97D-Link DHP-1565 User Manual
Section 3 - Conguration
The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the
connected wireless clients.
Wireless
98D-Link DHP-1565 User Manual
Section 3 - Conguration
IPv6
The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
99D-Link DHP-1565 User Manual
Section 3 - Conguration
IPv6 Routing
This page displays the IPv6 routing details congured for your router.
100D-Link DHP-1565 User Manual
Section 3 - Conguration
Support
101D-Link DHP-1565 User Manual
Section 4 - Security
Wireless Connection Setup Wizard
To run the Wireless Connection Setup Wizard, click the Wireless Connection
Setup Wizard button in the Setup>Wireless Settings window.
102D-Link DHP-1565 User Manual
Section 4 - Security
Wireless Security Setup Wizard
Type your desired wireless network name (SSID).
Automatically: Select this option to automatically generate the
router’s network key and click Next.
Manually: Select this option to manually enter your network key
and click Next.
If you selected Automatically, the summary window will display your
settings. Write down the security key and enter this on your wireless clients.
Click Save to save your settings.
The Changes have been saved. Click Reboot Now or Reboot Later to
continue.
103D-Link DHP-1565 User Manual
Section 4 - Security
If you selected Manually, the following screen will appear.
Enter the Wireless Security Password you would like to use for your wireless
network and click Next to proceed to the next window.
The summary window will display your settings. Write down the security
key and enter this on your wireless clients. Click Save to save your settings.
104D-Link DHP-1565 User Manual
Section 4 - Security
From the Setup > Wireless Settings screen, click Add Wireless Device
with WPS.
Add Wireless Device with WPS Wizard
PIN: Select this option to use PIN method. In order to use this method you
must know the wireless client’s 8 digit PIN and click Connect.
PBC: Select this option to use PBC (Push Button) method to add a wireless
client. Click Connect.
Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once
you select Auto and click Connect, you will have a 120 second time limit
to apply the settings to your wireless client(s) and successfully establish
a connection.
If you select Manual, a settings summary screen will appear. Write down
the security key and enter this on your wireless clients.
105D-Link DHP-1565 User Manual
Section 3 - Conguration
Conguration (AP Mode)
This section will show you how to congure your new D-Link wireless router using the web-based conguration utility.
Web-based Conguration Utility
To access the conguration utility, open a web-browser such as Internet
Explorer and enter http://dlinkrouter or the IP address of the router
(192.168.0.1).
Select Admin in the User Name eld. Leave the password blank by default.
If you get a Page Cannot be Displayed error, please refer to the
Troubleshooting section for assistance.
106D-Link DHP-1565 User Manual
Section 3 - Conguration
Wireless Setup Wizard
To use our web-based wizard to assist you in connecting your DHP-1565,
click Launch Wireless Setup Wizard to begin.
Click Next to continue your wireless network setup.
Select one of the two conguration methods. Select WPS if your wireless
device support WPS and click Next to continue to the next step.
Press down the Push Button on the wireless device within 116 seconds.
107D-Link DHP-1565 User Manual
Section 3 - Conguration
If you would like to setup your network manually, select Manual and click
Next to continue.
Enter the SSID (Service Set Identifier). The SSID is the name of your
wireless network. Create a name using up to 32 characters. The SSID is
case-sensitive. Select Assign a network key and click Next.
Once this screen appears, the setup is complete. You will be given a detailed
summary of your wireless security settings.
Click Save to continue.
108D-Link DHP-1565 User Manual
Section 3 - Conguration
Wireless Setup
Check this box to enable the wireless function. If you
would prefer not to use wireless, uncheck the box to
disable all the wireless functions. You may also set up a
specic time range (schedule). Select a schedule from
the drop-down menu or click Add New Schedule to
create a new schedule.
When you are browsing for available wireless
networks, this is the name that will appear in the list
(unless Visibility Status is set to Invisible, see below).
This name is also referred to as the SSID. For security
purposes, changing the default network name is
highly recommended.
Select one of the following:
802.11n Only - Select if you are only using 802.11n
wireless clients.
Mixed 802.11n, 802.11g and 802.11b - Select if you are
using a mix of 802.11n, 11g, and 11b wireless clients.
Mixed 802.11n, 802.11g - Select if you are only using
802.11n, 11g wireless clients.
The Auto Channel Scan setting can be selected to
allow the DHP-1565 to select the channel with the least
amount of interference (during boot-up). Indicates the
channel setting for the DHP-1565.
The channel can be changed to t the channel setting
for an existing wireless network or to customize the
wireless network. If you enable Auto Channel Scan,
this option will be grayed out.
Enable
Wireless:
Wireless
Network
Name:
802.11
Mode:
Enable Auto
Channel
Scan :
Wireless
Channel
109D-Link DHP-1565 User Manual
Section 3 - Conguration
Channel
Width:
Wireless
Security
Settings:
Save Settings:
Select the Channel Width:
Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
Locking the wireless security settings prevents the settings from being changed by any new external user using its PIN. Devices
can still be added to the wireless network using Wi-Fi Protected Setup. It is still possible to change wireless network
settings with Manual Wireless Network Setup, Wireless Network Setup Wizard, or an existing external WLAN Manager
user. Please refer to page 121.
Click Save Settings to save and activate the new changes.
110D-Link DHP-1565 User Manual
Section 3 - Conguration
Network Settings - DHCP
This section will allow you to change the local network settings of the access point and to congure the DHCP settings.
LAN
Connection
Type:
Device Name:
Save Settings:
Use the drop-down menu to select Dynamic IP (DHCP)
to automatically obtain an IP address on the LAN/private
network.
Enter the Device Name of the AP. Changing the Device
Name is recommended if there is more than one D-Link
device within the subnet.
Click Save Settings to save and activate the
new changes.
111D-Link DHP-1565 User Manual
Section 3 - Conguration
Select Static IP to manually enter the IP address, subnet mask, and default gateway addresses.
LAN Connection
Type:
IP Address:
Subnet Mask:
Default
Gateway:
Device Name:
Save Settings:
Select Static IP from the drop-down menu.
Enter the IP address of the access point. The default IP
address is 192.168.0.1. If you change the IP address, once
you click Apply, you will need to enter the new IP address
in your browser to return to the conguration utility.
Enter the Subnet Mask.
Enter the Gateway. This is usually the LAN or internal IP
address of your router.
Enter the Device Name of the AP. It is recommended that you
change the Device Name if there is more than one D-Link
device within the subnet. You can enter the device name
of the AP into your web browser to access it instead of IP
address for conguration. If you are using the device name
to connect, make sure that your PC and your DHP-1565 are
on the same network.
Click Save Settings to save and activate the new changes.
Network Setup - Static IP
112D-Link DHP-1565 User Manual
Section 3 - Conguration
My IPv6
Connection is:
LAN IPv6 Address
settings:
Select Link-local only from the drop-down menu.
This section displays the IPv6 address of the router.
My IPv6
Connection is:
LAN IPv6
Address:
Select static IPv6 from the drop-down menu.
Enter the LAN (local) IPv6 address for the router.
113D-Link DHP-1565 User Manual
Section 3 - Conguration
My IPv6
Connection:
IPv6 DNS
Settings:
Select Autoconguration (Stateless/DHCPv6) from
the drop down menu.
Select Obtain IPv6 DNS Server automatically or enter
a specic DNS Server address.
114D-Link DHP-1565 User Manual
Section 3 - Conguration
Conguration
This section will show you how to congure your new D-Link PowerLine AV using the web-based conguration utility.
PLC Settings - AP Mode
115D-Link DHP-1565 User Manual
Section 3 - Conguration
Network
Name:
Public
Network
Name:
Private
Network
Name:
Scan:
Add Member:
Device Name:
Password:
Member List:
Link Rate:
Status:
You can set the name of your network and to make it either public
or private. Make sure the Network Name of all of the devices
within your PowerLine network is the same.
Select this option if you would like to make your PowerLine
network public with the default Network Name of “HomePlugAV”.
Since this is a commonly used Network Name, it is less secure
than a private Network Name.
Select this option if you wish to make your PowerLine network
more secure by using a private Network Name. Type the name
of your private PowerLine network in the eld.
Scan for new PowerLine devices.
This section lets you add new PowerLine AV devices to your
PowerLine network. To add a new device, give it a Device Name
and enter its Password, then click Add. When you add a device
it is given the current Network Name.
Type a name you wish to use to identify a specic PowerLine AV
device. For example, “Jack’s room”.
The Password is used to verify that you are authorized to perform changes on a device. You can nd the Password printed on the
back of your device.
This section provides information on the PowerLine AV devices in your PowerLine network, or any devices that were previously
connected but it are currently disconnected.
Displays the device’s current data rate in Mbps.
This eld shows the status of the device. If the eld displays the word Connect, then the device is connected to your PowerLine
116D-Link DHP-1565 User Manual
Section 3 - Conguration
QoS Settings:
Mac Address:
network. If the eld displays the word Disconnect, then
the device has been added to the network but it is not
ready. Please check its password and make sure the device
is powered on.
You can congure your PowerLine AV devices to give
priority to the powerline network trac accordingly. Enter
the name, MAC Address, and priority level.
You can nd the MAC address printed on the back of your
device.
117D-Link DHP-1565 User Manual
Section 3 - Conguration
Use MAC (Media Access Control) Filters to authorize wireless clients to access your network by their MAC addresses. When enabled, any client not
on the MAC lter list will not be able to access your network.
MAC Address
Filter:
MAC Address:
Wireless Client
List:
Save Settings:
Select Enable or Disable from the drop-down
menu.
Enter the MAC address you would like to lter.
To nd the MAC address on a computer, please refer
to the Networking Basics section in this manual. Click
Save Settings to activate and save.
Note: Make sure to enter the computer you are
currently using to congure the access point rst or
you will not be able to access the conguration utility
once you click Save Settings.
Select a DHCP client from the drop-down menu and
click to copy the MAC Address.
Click Save Settings to save and activate the new
changes.
Network Filter
118D-Link DHP-1565 User Manual
Section 3 - Conguration
Advanced Wireless
Transmit
Power:
WLAN
Partition:
WMM Enable:
Short GI:
Sets the transmit power of the antennas.
Note: Transmit power is regulated by international
standard. Users are forbidden to change its maximum limit.
Select this checkbox to enable WLAN partition. If this
feature is enabled, then there is no barrier between
communication among wireless stations connecting to
the Access Point. If this is disabled, wireless clients are not
allowed to exchange data through the Access Point.
WMM is a Quality of Service (QoS) system for your wireless network. Enabling this feature will improve the quality of video and ice
applications for your wireless clients.
Check this box to reduce the guard interval time therefore increasing the data capacity. However, this setting less reliable and may
create higher data loss.
119D-Link DHP-1565 User Manual
Section 3 - Conguration
Wi-Fi Protect
Setup:
Reset to
Uncongure:
Current PIN:
Generate New
PIN:
Reset PIN to
Default:
Enables the Wi-Fi Protected Setup feature.
Restores the default Wi-Fi setup.
Shows the current value of the access
point’s PIN.
Create a random number that is a valid
PIN. This becomes the access point’s PIN.
You can then copy this PIN to the user
interface of the user.
Restores the default PIN of the access
point.
Wi-Fi Protect Setup
120D-Link DHP-1565 User Manual
Section 3 - Conguration
Add Wireless Device with WPS
Adding a Wireless Device Using the PIN Method
Please select one of the following conguration methods and click
Next to continue.
Click Add Wireless Device with WPS.
If your wireless device supports WPS, select Auto and click Next to
continue.
121D-Link DHP-1565 User Manual
Section 3 - Conguration
Adding a Wireless Device Using the PBC Method
Select PBC to use Push Button Conguration in order to connect to
your network.
Click Connect to continue.
Press the WPS Button on the wireless device that you are adding to
your network to complete the setup.
122D-Link DHP-1565 User Manual
Section 3 - Conguration
Manually Add Wireless Device with WPS
If you would like to add a wireless device with WPS manually, select
Manual and click Next to continue.
Enter the following settings in the wireless device you are adding to
your wireless network. Click Ok to continue.
123D-Link DHP-1565 User Manual
Section 3 - Conguration
User Limit Settings
In this section, you may set a limit to the number of wireless clients to prevent heavy wireless trac.
124D-Link DHP-1565 User Manual
Section 3 - Conguration
Admin
This page will allow you to change the Administrator password. The administrator password has read/write access.
Enter a new password for the Admin User
Name. The administrator account can change
the conguration of the device.
Enter the same password that you entered in
the previous textbox in order to conrm its
accuracy.
Enter DHP-1565.
Enables a challenge-response test which will
require users to type letters or numbers from
a distorted image displayed on the screen
to prevent online hackers and unauthorized
users from gaining access to your device’s
configuration. This feature is disabled by
default.
Click Save Settings to save and activate the
new changes.
Password:
Verify
Password:
System Name:
Enable
Graphical:
Save Settings:
125D-Link DHP-1565 User Manual
Section 3 - Conguration
Time
This page will allow you to change the Administrator password. The administrator password has read/write access.
Select the Time Zone from the drop-down menu.
To select Daylight Saving time manually, select
enabled or disabled, and enter a start date and an
end date for daylight saving time.
NTP is short for Network Time Protocol. NTP
synchronizes computer clock times in a network
of computers. Check this box to use a NTP server.
This will only connect to a server on the Internet,
not a local server.
Enter the NTP server or select one from the drop
down menu.
To manually input the time, enter the values in
these elds for the Year, Month, Day, Hour, Minute,
and Second and then click Set Time. You can also
click Copy Your Computer’s Time Settings.
Time Zone:
Daylight
Saving:
Enable NTP
Server:
NTP Server
Used:
Manual:
126D-Link DHP-1565 User Manual
Section 3 - Conguration
System Settings
Use this option to save the current router conguration
settings to a le on the hard disk of the computer you
are using. First, click the Save button. You will then
see a le dialog, where you can select a location and
le name for the settings.
Use this option to load previously saved router
conguration settings. First, use the Browse control
to nd a previously save le of conguration settings.
Then, click the Load button to transfer those settings
to the router.
This option will restore all conguration settings
back to the settings that were in eect at the time
the router was shipped from the factory. Any settings
that have not been saved will be lost, including any
rules that you have created. If you want to save the
current router conguration settings, use the Save
button above.
Click to reboot the router.
Save Settings to
Local Hard Drive:
Load Settings
from Local Hard
Drive:
Restore to
Factory Default
Settings:
Reboot Device:
127D-Link DHP-1565 User Manual
Section 3 - Conguration
Firmware
You can upgrade the rmware of the access point from this page. Make sure the rmware you would like to use is on the local hard drive of your
computer. Click Browse... to locate the rmware le to be used for the update. Please check the D-Link support site for rmware updates at
http://support.dlink.com. You can download rmware upgrades to your hard drive from the D-Link support site.
Click on the Check Now button to nd out if
there is an updated rmware or language pack
version. If a new version exists, download the
new rmware to your hard drive.
After you have downloaded the new rmware,
click Browse to locate the rmware update on
your hard drive. Click Upload to complete the
rmware upgrade.
Check Online for the latest rmware version in
order to have your router check automatically
for new rmware upgrades.
Firmware
Information:
Firmware
Upgrade:
Notication
Options:
After you have downloaded the new language
pack, click Choose File to locate the language
pack le on your hard drive. Click Upload to
complete the language pack upgrade.
Note: In most cases you must unzip the le rst
before uploading.
Language Pack
You can change the language of the web UI by uploading
available language packs.
Choose File:
128D-Link DHP-1565 User Manual
Section 3 - Conguration
System Check
The Ping Test is used to send Ping packets to
test if a computer is on the Internet. Enter the IP
Address or host name that you wish to Ping and
click Ping.
The results of your ping attempts will be
displayed here.
Ping Test:
Ping Results:
129D-Link DHP-1565 User Manual
Section 3 - Conguration
Schedules
Name:
Days:
Time:
Add:
Schedule
Rules
List:
Schedules can be created for use with enforcing rules. For example, if you would like to restrict web access to Mon-Fri from 3:00 p.m. to 8:00 p.m.,
you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3:00 p.m. and End Time of 8:00 p.m.
Enter a name for your new schedule.
Select a day, a range of days, or All Week to include
every day.
Check All Days or enter a start and end time for your
schedule.
After making your changes, click Save to save
the schedule rule.
The list of schedules will be listed here. Click the
Edit icon to make changes or click the Delete icon
to remove the schedule.
130D-Link DHP-1565 User Manual
Section 3 - Conguration
Device Info
This page displays the current information for the DHP-1565. It will display the LAN and wireless LAN information.
General:
LAN:
Wireless LAN:
Displays the access point’s time and rmware
version.
Displays the MAC address and the private
(local) IP settings for the access point.
Displays the wireless MAC address and your
wireless settings such as SSID and Channel.
Status
131D-Link DHP-1565 User Manual
Section 3 - Conguration
Logs
The DHP-1565 keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are automatically cleared. You can
save the log les under Log Settings.
Log Options:
First Page:
Last Page:
Previous:
Next:
Clear:
Log Settings:
Refresh:
You can select the types of messages that you
would like to display from the log: System
Activity, Debug Information, Attacks, Dropped
Packets, and Notice. Select the types you want
to view and click Apply Log Settings Now.
This button directs you to the rst page of the
log.
This button directs you to the last page of the
log.
This button directs you to the previous page
of the log.
This button directs you to the next page of the
log.
This button clears all current log content.
This button opens a new menu where you can
congure the log settings.
This button refreshes the log.
132D-Link DHP-1565 User Manual
Section 3 - Conguration
Statistics
The DHP-1360 keeps statistics of the trac that passes through it. You can view the amount of packets that pass through the LAN and wireless
portions of the network. The trac counter will reset if the access point is rebooted.
Refresh Statistics: Click the Refresh button to refresh the Access Point’s
trac statistics.
133D-Link DHP-1565 User Manual
Section 3 - Conguration
Wireless
This section allows you to view the wireless clients that are connected to your wireless access point.
134D-Link DHP-1565 User Manual
Section 3 - Conguration
IPv6
This section will display all of your IPv6 Internet and network connection details.
135D-Link DHP-1565 User Manual
Section 3 - Conguration
Support
136D-Link DHP-1565 User Manual
Section 4 - Security
Wireless Security
This section will show you the dierent levels of security you can use to protect your data from intruders. The
DHP-1565 oers the following types of security:
• WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key)
• WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm
and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.11i and
uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access
to a wireless network based on a computer’s hardware-specic MAC address, which is relatively simple to be snied out and stolen.
EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63
characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or
access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption
system to ensure that only authorized network users can access the network.
137D-Link DHP-1565 User Manual
Section 4 - Security
Congure WEP
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before
enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.
1. Log into the web-based conguration by opening a web browser and entering the IP address of the router (192.168.0.1).
2. Click on Setup and then click Wireless Settings on the left side.
3. Click the Manual Wireless Connection Setup button.
4. Next to Security Mode, select WEP.
5. Next to WEP Encryption, select 64bit or 128bit.
6. Next to Default WEP Key, select the WEP key you would like to use as the default
WEP key. The available option is WEP Key 1.
7. Enter the WEP key you would like to use in the WEP Key eld.
8. Click Save Settings to save your settings. If you are conguring the router with a
wireless adapter, you will lose connectivity until you enable WEP on your adapter
and enter the same WEP key as you did on the router.
138D-Link DHP-1565 User Manual
Section 4 - Security
Congure WPA/WPA2-Personal (PSK)
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before
enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.
1. Log into the web-based conguration by opening a web browser and entering the IP address of the router (192.168.0.1).
2. Click on Setup and then click Wireless Settings on the left side.
3. Click the Manual Wireless Connection Setup button.
4. Next to Security Mode, select WPA-Personal
5. Next to WPA Mode, select WPA/WPA2, WPA2 only or WPA only
6. Next to Cypher Type select TKIP, AES or TKIP and AES.
7. Enter the WPA network key you would like to use in the Network Key eld.
8. Click Save Settings to save your settings. If you are conguring the router with
a wireless adapter, you will lose connectivity until you enable WPA-PSK on your
adapter and enter the same passphrase as you did on the router.
139D-Link DHP-1565 User Manual
Section 4 - Security
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before
enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.
1. Log into the web-based conguration by opening a web browser and entering the IP address of the router (192.168.0.1).
2. Click on Setup and then click Wireless Settings on the left side.
3. Click the Manual Wireless Connection Setup button.
4. Next to Security Mode, select WPA- Enterprise.
5. Next to WPA mode, select Auto (WPA or WPA2), WPA2 only or WPA only.
6. Next to Cipher Type, select (TKIP/AES), TKIP, or AES.
7. Next to RADIUS Server IP Address enter the IP Address of your RADIUS server.
8. Next to Port, enter the port you are using with your RADIUS server. 1812 is the
default port.
9. Next to Shared Secret, enter the security key.
10. Click Save Settings to save your settings.
Congure WPA/WPA2-Enterprise (RADIUS)
140D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Using Windows® 7
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you
are joining an existing network, you will need to know the security key or passphrase being used.
1. Click on the wireless icon in your system tray (lower-right corner).
2. The utility will display any available wireless networks in your area.
Connect to a Wireless Network
Wireless Icon
141D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
3. Highlight the wireless network (SSID) you would like to connect to and click
the Connect button.
If you get a good signal but cannot access the Internet, check your TCP/IP
settings for your wireless adapter. Refer to the Networking Basics section in
this manual for more information.
4. The following window appears while your computer tries to connect to the
router.
142D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
5. Enter the same security key or passphrase that is on your router and click
Connect. You can also connect by pushing the WPS button on the router.
It may take 20-30 seconds to connect to the wireless network. If the connection
fails, please verify that the security settings are correct. The key or passphrase
must be exactly the same as on the wireless router.
143D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Congure WPS
The WPS feature of the router can be congured using Windows® 7. Carry out the following steps to use Windows® 7 to congure the WPS feature
of the router:
1. Click the Start button and select Computer from the Start menu.
2. Click the Network option.
144D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
3. Double-click the DHP-1565.
4. Input the WPS PIN number (displayed in the WPS window on the Router’s
LCD screen or in the Setup > Wireless Setup menu in the Router’s Web UI)
and click Next.
145D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
5. Type a name to identify the network.
6. To congure advanced settings, click the icon.
Click Next to continue.
146D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
7. The following window appears while the Router is being congured.
Wait for the conguration to complete.
8. The following window informs you that WPS on the DHP-1565 has been setup
successfully.
Make a note of the security key as you may need to provide this security key
if adding an older wireless device to the network in the future.
9. Click Close to complete WPS setup.
147D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Using Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user
manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows
Vista® utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right corner
next to the time). Select Connect to a network.
If you receive the Wireless Networks Detected bubble, click on the center of
the bubble to access the utility.
or
The utility will display any available wireless networks in your area. Click on a
network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/IP settings
for your wireless adapter. Refer to the Networking Basics section in this manual
for more information.
148D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Congure Wireless Security
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you
are joining an existing network, you will need to know the security key or passphrase being used.
2. Highlight the wireless network (SSID) you would like to connect to and click
Connect.
1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless
computer icon in your system tray (lower right corner of screen). Select
Connect to a network.
149D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
3. Enter the same security key or passphrase that is on your router and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the connection fails,
please verify that the security settings are correct. The key or passphrase must be
exactly the same as on the wireless router.
150D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Using Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Conguration Utility). The following instructions are for Service Pack 2 users. If you are
using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless
network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right corner
next to the time). Select View Available Wireless Networks.
If you receive the Wireless Networks Detected bubble, click on the center of the
bubble to access the utility.
or
The utility will display any available wireless networks in your area. Click on a
network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/IP settings
for your wireless adapter. Refer to the Networking Basics section in this manual
for more information.
151D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Congure WPA-PSK
It is recommended to enable WPA on your wireless router or access point before conguring your wireless adapter. If you are joining an existing
network, you will need to know the WPA key being used.
2. Highlight the wireless network (SSID) you would like to connect to and
click Connect.
1. Open the Windows® XP Wireless Utility by right-clicking on the wireless
computer icon in your system tray (lower-right corner of screen). Select
View Available Wireless Networks.
152D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase
and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the connection fails,
please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be
exactly the same as on the wireless router.
153D-Link DHP-1565 User Manual
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DHP-1565. Read the following descriptions
if you are having problems. The examples below are illustrated in Windows® XP. If you have a dierent operating system, the screenshots on your
computer will look similar to the following examples.
1. Why can’t I access the web-based conguration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you have to be connected
to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to
the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
- Microsoft Internet Explorer® 6.0 and higher
- Mozilla Firefox 3.0 and higher
- Google™ Chrome 2.0 and higher
- Apple Safari 3.0 and higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a dierent cable or
connect to a dierent port on the device if possible. If the computer is turned o, the link light may not be on.
• Disable any Internet security software running on the computer. Software rewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal
Firewall, and Windows® XP rewall may block access to the conguration pages. Check the help les included with your rewall software
for more information on disabling or conguring it.
154D-Link DHP-1565 User Manual
Section 6 - Troubleshooting
• Congure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore
the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing
is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the
login page for your web management.
• If you still cannot access the conguration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing
the conguration. If you have multiple computers, try connecting using a dierent computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button
down for 5 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default
IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.
155D-Link DHP-1565 User Manual
Section 6 - Troubleshooting
3. Why can’t I connect to certain sites or send and receive emails when connecting through my router?
If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering
the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
Note: AOL DSL+ users must use MTU of 1400.
To nd the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or
a URL.
• Click on Start and then click Run.
• Windows® 95, 98, and Me users type in command (Windows® NT, 2000, and XP users type in cmd) and press Enter (or click OK).
• Once the window opens, you’ll need to do a special ping. Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472
You should start at 1472 and work your way down by 10 each time. Once you get
a reply, go up by 2 until you get a fragmented packet. Take that value and add 28
to the value to account for the various TCP/IP headers. For example, lets say that
156D-Link DHP-1565 User Manual
Section 6 - Troubleshooting
1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Once you nd your MTU, you can now congure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
• Open your browser, enter the IP address of your router (192.168.0.1) and click OK.
• Enter your username (admin) and password (blank by default). Click OK to enter the web conguration page for the device.
• Click on Setup and then click Manual Congure.
• To change the MTU enter the number in the MTU eld and click Save Settings to save your settings.
• Test your e-mail. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten.
157D-Link DHP-1565 User Manual
Appendix A - Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your
home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to
securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless
LANs are used increasingly in both home and oce environments, and public areas such as airports, coee shops and universities. Innovative ways
to utilize WLAN technology are helping people to work and communicate more eciently. Increased mobility and the absence of cabling and other
xed infrastructure have proven to be benecial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support
the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers
or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link.
Wireless Basics
158D-Link DHP-1565 User Manual
Appendix A - Wireless Basics
What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect
wirelessly, so you have the freedom to connect computers anywhere in your home or oce network.
Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance
you need at a price you can aord. D-Link has all the products you need to build your network.
How does wireless work?
Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has
restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There
are two dierent types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna
attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can
travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial
locations, college and high school campuses, airports, golf courses, and many other outdoor venues.
Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away.
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which
makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, oce, business, D-Link has a
wireless solution for it.
159D-Link DHP-1565 User Manual
Appendix A - Wireless Basics
Home
• Gives everyone at home broadband access
• Surf the web, check e-mail, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Oce and Home Oce
• Stay on top of everything at home as you would at oce
• Remotely access your oce network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate oce space
160D-Link DHP-1565 User Manual
Appendix A - Wireless Basics
Where is wireless used?
Wireless technology is expanding everywhere not just at home or oce. People like the freedom of mobility and it’s becoming so popular that
more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels,
Coee Shops, Libraries, Restaurants, and Convention Centers.
Wireless network is easy to setup, but if you’re installing it for the rst time it could be quite a task not knowing where to start. That’s why we’ve put
together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your router or Access Point
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access
point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater
to boost the signal to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would
signicantly reduce any interference that the appliances might cause since they operate on same frequency.
Security
Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP
security feature on the router. Refer to product manual for detail information on how to set it up.
161D-Link DHP-1565 User Manual
Appendix A - Wireless Basics
There are basically two modes of networking:
• Infrastructure – All wireless clients will connect to an access point or wireless router.
• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each
computer, such as two or more DHP-1565 wireless network Cardbus adapters.
An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access
point.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate.
Wireless Modes
162D-Link DHP-1565 User Manual
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless
router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.)
At the prompt, type ipcong and press Enter.
This will display the IP address, subnet mask, and the default
gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation, security
settings, and the settings on your router. Some rewall software
programs may block a DHCP request on newly installed
adapters.
163D-Link DHP-1565 User Manual
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter Settings.
Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.
Windows® XP - Click on Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a
number between 2 and 99. Make sure that the number you choose is not in use on the network. Set
Default Gateway the same as the LAN IP address of your router (192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not
needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
164D-Link DHP-1565 User Manual
Appendix C - Technical Specications
Technical Specications
Standards
• IEEE 802.3
• IEEE 802.3u
• IEEE 802.11b
• IEEE 802.11g
• IEEE 802.11n
• HomePlug AV
Ethernet Interface
• 10/100/1000 Base-TX Ethernet Port with Auto MDI/MDIX
• RJ-45 Connector
Security
• 128-bit AES Data encryption
• WEP 64/128-Bit Data encryption
• Wi-Fi Protected Access (WPA/WPA2)
• WPS™
Maximum PowerLine Data Rate
• 500 Mbps
Antenna
• Two fixed internal 3dBi PCB antennas
PowerLine Modulations Scheme
• OFDM Symbol Modulation
PowerLine Frequency Band
• 2Mhz to 70Mhz
Security
•128-bit AES Data encryption
• WEP 64/128-Bit Data encryption
• Wi-Fi Protected Access (WPA/WPA2)
• WPS™
LEDs
• Power • Internet
• Powerline
Power Saving
• Power saving mode supported
• Compliant with European Energy using Product Directive (EuP)
Safety Certications
• UL
EMC Certications
• FCC
• IC
Operating Temperature
• 30°F to 104°F (0°C to 40°C)
Operating Humidity
• 10% to 95% (Non-condensing)
1 Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including volume
of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely aect wireless signal range.
2 Frequency Range varies depending on country’s regulation
165D-Link DHP-1565 User Manual
Appendix C - Technical Specications
Wireless Signal Rates1
IEEE 802.11n:
20MHz Channel:
• 1Nss: 65/72.2 Mbps (max)
• 2Nss: 130/144.44 Mbps (max)
40MHz Channel:
• 1Nss: 135/150 Mbps (max)
• 2Nss: 270/300 Mbps (max)
IEEE 802.11g:
• 54Mbps • 48Mbps • 36Mbps
• 24Mbps • 18Mbps • 12Mbps
• 11Mbps • 9Mbps • 6Mbps
Wireless Frequency Range2 (North America)
• 2.412GHz to 2.462GHz (802.11g/n)
Warranty
• 1 Year
166D-Link DHP-1565 User Manual
Appendix D - Contacting Technical Support
Contacting Technical Support
U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g. DHP-1565)
• Hardware Revision (located on the label on the bottom of the router (e.g. rev A1))
• Serial Number (S/N number located on the label on the bottom of the router).
You can nd software updates and user documentation on the D-Link website as well as frequently asked questions and answers to technical issues.
For customers within the United States:
Phone Support:
(877) 453-5465
Internet Support:
http://support.dlink.com
For customers within Canada:
Phone Support:
(800) 361-5265
Internet Support:
http://support.dlink.ca
167D-Link DHP-1565 User Manual
Appendix E - Warranty
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fty states of the United States, the District of Columbia, U.S. Possessions
or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Limited Warranty:
D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship
and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except
as otherwise stated herein.
• Hardware (excluding power supplies): One (1) year
• Power supplies: One (1) year
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at
D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual
purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Oce. The replacement hardware
need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any
reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer,
and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical
to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link
upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded,
shall become the property of D-Link upon replacement or refund.
168D-Link DHP-1565 User Manual
Appendix E - Warranty
Limited Software Warranty:
D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specications
for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90)
days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its
documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be
free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will
be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional
specications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise
agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the
license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject
to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it
is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by
D-Link; provided that the non-conforming Software (and all copies thereof) is rst returned to D-Link. The license granted respecting any Software
for which a refund is given automatically terminates.
Non-Applicability of Warranty:
The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any
refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or
the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any
warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim:
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
The customer must submit with the product as part of the claim a written description of the Hardware defect or Software
nonconformance in sucient detail to allow D-Link to conrm the same, along with proof of purchase of the product (such as a
copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support (USA 1-877-453-5465 or Canada 1-800-361-5265), who
will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the
customer must obtain a Return Material Authorization (“RMA”) number by completing the RMA form. Enter the assigned Case ID
Number at https://rma.dlink.com/ (USA only) or https://rma.dlink.ca (Canada only).
169D-Link DHP-1565 User Manual
Appendix E - Warranty
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package
to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product
and will not ship back any accessories.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD
will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped
to D-Link Systems, Inc.
• USA residents send to 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that
are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common
carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise
we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are
prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to
pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance
with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
• Canadian residents send to D-Link Networks, Inc., 2525 Meadowvale Boulevard Mississauga, Ontario, L5N 5S2 Canada. D-Link will
not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to
the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link
if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited shipping is available upon
request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged
and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of
the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is
not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or
non-conforming. RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST
What Is Not Covered:
The Limited Warranty provided herein by D-Link does not cover:
Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modication, tampering, negligence, misuse, faulty installation,
lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number
has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act
of God, failures due to power surge, and cosmetic damage; Any hardware, software, rmware or other products or services provided by anyone
other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers,
or the liquidators expressly disclaim their warranty obligation pertaining to the product.
170D-Link DHP-1565 User Manual
Appendix E - Warranty
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Oce. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties:
EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY
SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE
LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE
PURCHASER OF THE PRODUCT.
Limitation of Liability:
TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL
OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT
IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK
FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF
THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM
LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING
EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED
OR STATUTORY.
Governing Law:
This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This
Limited Warranty provides specic legal rights and you may also have other rights which vary from state to state.
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their
respective owners.
171D-Link DHP-1565 User Manual
Appendix E - Warranty
Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the
United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright ©2011 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution:
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
172D-Link DHP-1565 User Manual
Appendix E - Warranty
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body. To maintain compliance with FCC RF exposure compliance requirements,
please avoid direct contact to the transmitting antenna during transmitting.
The availability of some specic channels and/or operational frequency bands are country dependent and are rmware programmed at the factory
to match the intended destination. The rmware setting is not accessible by the end user.
ICC Notice:
Operation is subject to the following two conditions:
(1) This device may not cause interference and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specic operating
instructions for satisfying RF exposure compliance. This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
This device has been designed to operate with an antenna having a maximum gain of 2 dB. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna impedance is 50 ohms.
Règlement d’Industry Canada
Les conditions de fonctionnement sont sujettes à deux conditions:
(1) Ce périphérique ne doit pas causer d’interférence et.
(2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le bon fonctionnement de
ce périphérique.
173D-Link DHP-1565 User Manual
Appendix F - Registration
Version 1.0
September 12, 2011
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Registration