D Link IR601LA1 Wireless N 150 Cloud Router User Manual D Link DIR 645

D Link Corporation Wireless N 150 Cloud Router D Link DIR 645

UserMan_KA2IR601LA1

DIR-601LWireless N150 Cloud Router
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes.PrefaceTrademarksD-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.Copyright © 2012 by D-Link Systems, Inc.All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc.
Section 1 - Product OverviewProduct OverviewPackage ContentsDIR-601L Wireless N150 Cloud Router Power Adapter Ethernet Cable Quick Installation Guide Check for the supplied accessories below: Note: Using a power supply with a dierent voltage rating than the one included with the product, will cause damage and void the warranty for this product.
Section 1 - Product OverviewSystem RequirementsNetwork Requirements• An Ethernet-based Cable or DSL modem• IEEE 802.11n or 802.11g wireless clients• 10/100 EthernetWeb-based Conguration Utility RequirementsComputer with the following:• Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapterBrowser Requirements:• Internet Explorer 6.0 or higher• Chrome 2.0 or higher• Firefox 3.0 or higher• Safari 3.0 or higher (with Java 1.3.1 or higher) Windows® Users: Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version.CD Installation Wizard RequirementsComputer with the following:• Windows® 7, Vista®, or XP with Service Pack 2• An installed Ethernet adapter
Section 1 - Product OverviewFeatures• Internet Connectivity -  In conjunction with a DSL or Cable Modem, this device provides high-speed Internet connectivity to your local network for up to four wired devices. • Wireless LAN functionality -  This router supports features like WMM, RF Output Level Control, WPS, and much more.• Networking -  This router comes with one WAN port and four LAN ports that enable up to four computers on your local network to be connected. • Wireless Distribution System (WDS) mode- The router supports WDS where it can extend the network coverage from another router.• Advanced Security -  The router also supports a range of security features like Network Filtering, Access Control, Website Filtering, Inbound Filtering, and SPI.• IPv6 - This router supports local IPv6 support and IPv6 Internet Connection. •User-friendly Setup Wizard - your router qickly and conveniently. The DIR-601L’s easy-to-use Web-based user interface lets you manage and congure
Section 2 - Hardware InstallationWireless Installation ConsiderationsThe router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or oce. The key to maximizing the wireless range is to follow these basic guidelines:1.  Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum. Each wall or ceiling can reduce your adapter’s range from 3 to 90 feet (1 to 30 meters.) Position your devices so that the number of walls and/or ceilings is minimized.2.  Be aware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick. Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.3.  Try to position access points, wireless routers, and computers so that the signal passes through open doorways and drywall. Materials such as glass, metal, brick, insulation, concrete and water can aect wireless performance. Large objects such as sh tanks, mirrors, le cabinets, metal doors and aluminum studs may also have a negative eect on range.4.  Keep your product at least 3 to 6 feet (1-2 meters) away from electrical devices or appliances that generate RF noise.5.  If you are using 2.4 GHz cordless phones, make sure that the 2.4 GHz phone base is as far away from your wireless device as possible. The base transmits a signal even if the phone in not in use. In some cases, cordless phones, X-10 wireless devices, and electronic equipment such as ceiling fans, uorescent lights, and home security systems may dramatically degrade wireless connectivity.
Section 2 - Hardware InstallationConnect to Cable/DSL/Satellite ModemIf you are connecting the router to a Cable/DSL/Satellite Modem, please follow the steps below:1.  Place the router in an open and central location. Do not plug the power adapter into the router.2.  Turn the power o on your modem. If there is no on/o switch, unplug the modem’s power adapter. Shut down your computer.3.  Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router.4.  Plug an Ethernet cable into one of the LAN ports on the router. Plug the other end into the Ethernet port on your computer.5.  Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).6.  Plug the power adapter into the router and connect to an outlet or power strip. Wait about 30 seconds for the router to boot up.7.  Turn on your computer.8.  Verify that the Power LED on the router is lit. If the Power LED does not light up, make sure your computer, modem, and router are powered, on and verify that the cables connected correctly.9.  In a later section in this manual we’ll discuss the Web GUI conguration of the router in more detail..
Section 3 - Software CongurationCongurationThis section will show you how to congure your new D-Link wireless router using the web-based conguration utility.Web-based Conguration UtilityTo access the conguration utility, open a web browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).You  may also  connect  using the NetBIOS  name in the  address bar (http://dlinkrouter).Enter your password. Admin is  the default  username  and cannot be changed.  The password is left blank by default.If you get a Page Cannot be Displayed error message, please refer to the Troubleshooting section for assistance.Click Login to log into the Router.
Section 3 - Software CongurationSetup WizardClick Internet Connection Setup Wizard to quickly  congure your router. Skip to the next page. If you want to enter your settings  without running the  wizard, click Manual Conguration and skip to page 20.Internet Connection
Section 3 - Software CongurationInternet Connection(Setup Wizard)When conguring the router for the rst time, we recommend that you click Internet Connection Setup Wizard, and follow the instructions on the screen. This wizard is designed to assist user with a quick and easy method to congure the Internet connection of this router.Anytime during the Internet Connection Setup Wizard, you can click on Cancel to discard any changes made and return to the main Internet page. Also you can click on Prev to return to the previous window for re-conguration.This wizard will guide you through a step-by-step process to congure your new D-Link router and connect to the Internet. Click Next to continue.Step 1: Set Your PasswordBy default, the D-Link Router does not have a password congured for administrator access to the Web-based conguration pages. To secure your new networking device, please enter and verify a password in the spaces provided. The two passwords must match.Click Next to continue.
Section 3 - Software CongurationStep 2: Select Your Time ZoneSelect the appropriate time zone for your location. This information is required to congure the time-based options for the router. Click Next to continue.Step 3: Internet ConnectionHere the user will be able to congure the Internet Connectivity used by this device. If your ISP connection is listed in the drop-down menu select  it  and  click  Next. If  your ISP  connection  is  not  listed  then  you can  proceed  to  select  any  of  the  other  manual  Internet  Connection methods listed below.Dynamic IP Address:Choose  this  if  your  Internet  connection automatically  provides  you  with  an  IP  Address. Most Cable Modems use this type of connection.PPPoE: Choose  this  option  if  your  Internet  connection requires  a  PPPoE  username  and  password  to get  online.  Most  DSL  modems  use  this  type  of connection.PPTP: Choose  this  option  if  your  Internet  connection requires  a  PPTP  username  and  password  to  get online.L2TP: Choose  this  option  if  your  Internet  connection requires an L2TP username and password to get online.Static IP Address: Choose this option if your Internet Setup Provider provided you with IP Address information that has to be manually congured.
Section 3 - Software CongurationStep 3: Internet Connection (Dynamic IP Address)After  selecting  the  Dynamic  IP  Address Internet  connection  method, the following page will appear.MAC Address: Enter  the  MAC  address  of  the  Internet  gateway (plugged into the Internet port of this device).Clone Button: If  the  conguration  PC  also  acts  as  the  Internet gateway,  then  click  on  the  Clone Your  PC’s  MAC Address button to copy the PC’s MAC address into the  space  provided.  If  you’re  not  sure,  leave  the MAC Address eld blank.Host Name: Enter the host name used. You may also need to provide a Host Name. If you do not have or know this information, please contact your ISP.Primary DNS Address:Enter the Primary DNS IP address used.Secondary DNS Address:Enter the Secondary DNS IP address used. This eld is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability.Click Next to continue.
Section 3 - Software CongurationStep 3: Internet Connection (PPPoE)After selecting  the  PPPoE Internet connection method, the  following page will appear:Address Mode: The  user  can  specify  whether  this  Internet connection requires the use of a Dynamic or Static IP  address.  PPPoE  usually  requires  a  Dynamic  IP conguration.IP Address: Enter  the  PPPoE  IP  address  used.  This  option  is only available if Static IP is selected.User Name: Enter  the  PPPoE  account  user  name  used.  This information is given by the ISP.Password: Enter  the  PPPoE  account  password  used.  This information is given by the ISP.Verify Password: Re-enter the PPPoE account password used.Service Name: This  optional  eld  enables  the  user  to  enter  a service name to identify this Internet connection.Primary DNS Address:Enter the Primary DNS IP address used.Click Next to continue.
Section 3 - Software CongurationStep 3: Internet Connection (PPTP)After selecting the PPTP Internet connection method, the following page will appear:Address Mode: Here  the  user  can  specify  whether  this  Internet connection requires the use of a Dynamic or Static IP  address.  PPTP  usually  requires  a  Dynamic  IP conguration.PPTP IP Address: Enter the PPTP IP address used here. This option is only available if Static IP is selected.PPTP Subnet Mask:Enter the PPTP Subnet Mask used.PPTP Gateway IP Address:Enter the PPTP Gateway IP address used.PPTP Server IP Address:Enter  the  PPTP  Server  IP  address  used.  This  is normally the same as the PPTP Gateway IP address.User Name: Enter the PPTP username used.Password: Enter the PPTP password used.Verify Password: Re-enter the PPTP password used.Primary DNS Address:Enter the Primary DNS IP address used.Secondary DNS Address:Enter the Secondary DNS IP address used. This eld is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability.Click Next to continue.
Section 3 - Software CongurationStep 3: Internet Connection (L2TP)After  selecting  the  L2TP  Internet  connection  method,  the  following page will appear:Address Mode: Here  the  user  can  specify  whether  this  Internet connection requires the use of a Dynamic or Static IP  address.  L2TP  usually  requires  a  Dynamic  IP conguration.L2TP IP Address: Enter the L2TP IP address used here. This option is only available if Static IP is selected.L2TP Subnet Mask:Enter the L2TP Subnet Mask used.L2TP Gateway IP Address:Enter the L2TP Gateway IP address used.L2TP Server IP Address:Enter  the  L2TP  Server  IP  address  used.  This  is normally the same as the L2TP Gateway IP address.User Name: Enter the L2TP username used.Password: Enter the L2TP password used.Verify Password: Re-enter the L2TP password used.Primary DNS Address:Enter the Primary DNS IP address used.Secondary DNS Address:Enter the Secondary DNS IP address used. This eld is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability.Click Next to continue.
Section 3 - Software CongurationStep 3: Internet Connection (Static IP Address)After selecting the Static IP Address Internet connection method, the following page will appear:IP Address: Enter the Static IP address provided by the ISP.Subnet Mask: Enter the Subnet Mask provided by the ISP.Gateway Address:Enter the Gateway IP address provided by the ISP.Primary DNS Address:Enter the Primary DNS IP address used.Secondary DNS Address:Enter  the  Secondary  DNS  IP  address  used.  This eld is  normally  optional. Only one DNS  address is  required  for  a  functional  Internet  connection, but  using  a  second  DNS  address  provides  more stability.Click Next to continue.Setup Complete!This is the last page of the Internet Connection Setup Wizard. Click the Connect button to save your settings.
Section 3 - Software CongurationManual CongurationAt any given point the user can save the conguration done by clicking on  the  Save  Settings  button.  If  you  choose  to  discard  the  changes made, click on the Don’t Save Settings.Internet Connection TypeIn  this  section,  the  user  can  select  from  a  list  of  Internet  Connection types that can be congured and used on this router. Options to choose from are Static IP, Dynamic IP, PPPoE, PPTP, L2TP, and DS-Lite.After  selecting  a  specic  Internet  Connection  type,  this  page  will automatically refresh and display unique elds to congure related to the specied Internet Connection type.My Internet Connection is: Dynamic IP (DHCP)The default WAN conguration for this router is Dynamic IP (DHCP). This option allows the router to obtain an IP address automatically from the device that is connected to the Internet port. Note: If you’re not sure about the type of Internet Connection you have, please contact your Internet Service Provider (ISP) for assistance.Host Name: The Host Name is optional but may be required by some ISPs. Leave it blank if you are not sure.Use Unicasting: Tick this option if your ISP uses the unicast method to provide IP addresses.Primary DNS: Enter the Primary DNS IP address used.On this page the user can congure the Internet Connection settings manually. To access the Manual Internet Connection Setup page, click on the Manual Internet Connection Setup button. On this page there are multiple parameters that can be congured regarding the Internet Connection setup. We’ll discuss them from top to bottom.
Section 3 - Software CongurationSecondary DNS: Enter the Secondary DNS IP address used. This eld is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability.MTU:  Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1500 is the default MTU.MAC Address: The  default  MAC  Address is  set  to  the  Internet port’s  physical interface  MAC  address  on  the  Broadband  Router.  It  is  not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.My Internet Connection is: Static IPAnother Internet Connection type is Static IP. This option allows the user to manually congure the Static IP Internet Connection type. Normally the information entered will be supplied by your ISP. IP Address: Enter the Static IP address provided by the ISP.Subnet Mask: Enter the Subnet Mask provided by the ISP.Default Gateway:Enter the Gateway IP address provided by the ISP.Primary DNS: Enter the Primary DNS IP address used.Secondary DNS: Enter  the  Secondary  DNS  IP  address  used.  This eld is  normally  optional. Only one DNS  address is  required  for  a  functional  Internet  connection, but  using  a  second  DNS  address  provides  more stability.MTU: Maximum  Transmission  Unit  -  you  may  need  to change  the  MTU  for  optimal  performance  with your specic ISP. 1500 is the default MTU.MAC Address:  The  default  MAC  Address is  set  to  the  Internet port’s  physical interface  MAC  address  on  the  Broadband  Router.  It  is  not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Section 3 - Software CongurationMy Internet Connection is: PPPoE (Username/Password)Another Internet Connection type is PPPoE. This option is typically used if you have a DSL Internet Connection. Make sure to remove the PPPoE software installed on your computer rst before using this connection type. Most of the information needed for this connection type is provided to you by your ISP.Address Mode: Here  you  can  specify  whether  the  Internet connection requires the use of a Dynamic or Static IP  address.  PPPoE  usually  requires  a  Dynamic  IP conguration.IP Address: Enter the PPPoE IP address used here. This option is only available if Static IP is selected.Username: Enter  the  PPPoE  account  user  name  used.  This information is given by the ISP.Password: Enter  the  PPPoE  account  password  used.  This information is given by the ISP.Verify Password: Re-enter the PPPoE account password used.Service Name: This  optional  eld  enables  the  user  to  enter  a service name to identify this Internet connection.Reconnect Mode:Use  the  radio  buttons  to  specify  the  reconnect mode.  The  user  can  specify  a  custom  schedule or specify the On Demand, or Manual option. To specify  a  custom  schedule,  use  the  drop-down menu to select one of the schedules that has been dened  in  the  Schedules  page. To  create  a  new schedule, click the New Schedule button to open the Schedules page. Schedules will  be discussed later.Maximum Idle Time: Enter a maximum idle time during which the Internet connection is maintained during inactivity. DNS Mode:  This option allow the router to obtain the DNS IP addresses from the ISP, when Receive DNS from ISP is selected, or allows the user to enter the DNS IP address manually, when Enter DNS Manually is selected.Primary DNS Server: Enter the Primary DNS IP address used here.
Section 3 - Software CongurationSecondary DNS Server: Enter the Secondary DNS IP address used here. This eld is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability.MTU:  Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default MTU.MAC Address: The  default  MAC  Address is  set  to  the  Internet port’s  physical interface  MAC  address  on  the  Broadband  Router.  It  is  not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Section 3 - Software CongurationMy Internet Connection is: PPTP (Username/Password)Another Internet Connection type is PPTP. This option is typically used if you have a secure DSL Internet Connection. Most of the information needed for this connection type is provided to you by your ISP.Address Mode:  Here  the  user  can  specify  whether  this  Internet connection  requires  the  use  of  a  Dynamic  or Static IP address. PPTP usually requires a Dynamic IP conguration.PPTP IP Address: Enter the PPTP IP address used. This option is only available if Static IP is selected.PPTP Subnet Mask:Enter the PPTP Subnet Mask used.PPTP Gateway IP Address:Enter the PPTP Gateway IP address used.PPTP Server IP Address:Enter  the  PPTP  Server  IP  address  used.  This  is normally the same a the PPTP Gateway IP address.Username: Enter the PPTP username used.Password: Enter the PPTP password used.Verify Password: Re-enter the PPTP password used.Reconnect Mode:Use  the  radio  buttons  to  specify  the  reconnect mode.  The  user  can  specify  a  custom  schedule or specify the On Demand, or Manual option. To specify  a  custom  schedule,  use  the  drop-down menu  to  select  one  of  the  schedules  that  has been dened in  the  Schedules  page. To  create a new  schedule,  click  New  Schedule  to  open  the Schedules page. Schedules will be discussed later.
Section 3 - Software CongurationMaximum Idle Time: Enter a maximum  idle  time during which  the  Internet connection is maintained  during  inactivity. To disable  this feature, enable Auto-reconnect.Primary DNS Server: Enter the Primary DNS IP address used.Secondary DNS Server:Enter the Secondary DNS IP address used. This eld is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability.MTU:  Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1400 is the default MTU.MAC Address:  The  default  MAC  Address is  set  to  the  Internet port’s  physical interface  MAC  address  on  the  Broadband  Router.  It  is  not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.My Internet Connection is: L2TP (Username/Password)Another Internet Connection type is L2TP. This option is typically used if you have a secure DSL Internet Connection. Most of the information needed for this connection type is provided to you by your ISP.
Section 3 - Software CongurationAddress Mode: The  user  can  specify  whether  this  Internet connection requires the use of a Dynamic or Static IP  address.  L2TP  usually  requires  a  Dynamic  IP conguration.L2TP IP Address: Enter the L2TP IP address used. This option is only available if Static IP is selected.L2TP Subnet Mask:Enter the L2TP Subnet Mask used.L2TP Gateway IP Address:Enter the L2TP Gateway IP address used.L2TP Server IP Address:Enter  the  L2TP  Server  IP  address  used.  This  is normally the same as the L2TP Gateway IP address.Username: Enter the L2TP username used.Password: Enter the L2TP password used.Verify Password: Re-enter the L2TP password used.Reconnect Mode:Use  the  radio  buttons  to  specify  the  reconnect mode.  The  user  can  specify  a  custom  schedule or specify the On Demand, or Manual option. To specify  a  custom  schedule,  use  the  drop-down menu to select one of the schedules that has been dened  in  the  Schedules  page. To  create  a  new schedule,  click  the  New  Schedule  to  open  the Schedules page. Schedules will be discussed later.Maximum Idle Time:Enter a maximum  idle  time during which  the  Internet connection is maintained  during  inactivity. To disable  this feature, enable Auto-reconnect.Primary DNS Server:Enter the Primary DNS IP address used.Secondary DNS Server:Enter the Secondary DNS IP address used. This eld is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability.
Section 3 - Software CongurationMTU:  Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1400 is the default MTU.MAC Address:  The  default  MAC  Address is  set  to  the  Internet port’s  physical interface  MAC  address  on  the  Broadband  Router.  It  is  not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Section 3 - Software CongurationMy Internet Connection is: DS-Lite)Another Internet Connection type is DS-Lite. After selecting  DS-Lite, the  following parameters will be available for conguration:DS-Lite Conguration:Select the DS-Lite DHCPv6 Option to let the router allocate  the  AFTR  IPv6  address  automatically. Select  the  Manual  Conguration  to  enter  the AFTR IPv6 address in manually.AFTR IPv6 Address:After  selecting  the  Manual  Conguration  option above,  the user can  enter the  AFTR  IPv6  address used.B4 IPv4 Address: Enter the B4 IPv4 address value used.WAN IPv6 Address:Once  connected,  the  WAN  IPv6  address  will  be displayed.IPv6 WAN Default GatewayOnce connected, the  IPv6 WAN  Default  Gateway address will be displayed.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationWireless SettingsOn this page the user can congure the Wireless settings for this device. There are 3 ways to congure Wireless using this router. Firstly, the user can choose to make use for the quick and  easy Wireless Connection Setup Wizard. Secondly, the user can choose to make use Wi-Fi Protected Setup. Lastly, the user can congure the Wireless settings manually.Wireless Settings: Wireless Connection Setup WizardThe Wireless  Connection  Setup Wizard  is  specially  designed  to  assist basic network users with a  simple, step-by-step set of  instructions to congure the wireless settings of this router. It is highly recommended to customized the wireless network settings to t into your environment and to add higher security.To initiate the Wireless Connection Setup Wizard click on the Wireless Connection Setup Wizard button.Step  1:  In  this  step,  the  user  must  enter  a  custom  Wireless  Network Name  or  SSID.  Enter  the  new  SSID  name  in  the  appropriate  space provided. Secondly the user can choose between two wireless security wizard  congurations.  The  user  can  select  ‘Automatically  assign  a network key’, by which the router will automatically generate a WPA/WPA2 pre-shared key using the TKIP and AES encryption methods; or the user can select ‘Manually assign a network key’, by which the user will be prompt to manually enter a WPA/WPA2 pre-shared key using the TKIP and AES encryption methods.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page.
Section 3 - Software CongurationStep 2: This  step  will  only  be  available  if  the  user  selected ‘Manually assign a network key’ in the previous step. Here the user can manually enter the WPA/WPA2 pre-shared key in the Wireless Security Password space provided. The key entered must be between 8 and 63 characters long. Remember, this key will be used when wireless clients wants to connect to this device. So please remember this key to prevent future troubleshooting.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page.Setup  Complete:  On  this  page  the  user  can  view  the  conguration made and verify whether they are correct.Click on the Prev button to return to the previous page. Click on the Cancel  button  to  discard  the  changes  made  and  return  to  the  main wireless page. Click on the Save button to accept the changes made.After click the Save button the device will save the settings made and return to the main wireless page.
Section 3 - Software CongurationWireless Settings: Wi-Fi Protected Setup WizardIf your Wireless Clients support the WPS connection method, this Wi-Fi Protected Setup Wizard can be  used to initiate a wireless connection between this device and Wireless clients with a simple click of the WPS button. The Wi-Fi Protected Setup Wizard is specially designed to assist basic network users with a  simple, step-by-step set of  instructions to connect wireless clients to this router using the WPS method.To initiate the Wi-Fi Protected Setup Wizard click on the Add Wireless Device with WPS button.Step  1:  In  this  step  the  user  have  two  options  to  choose  from. You can choose Auto if the wireless client supports WPS, or Manual if the wireless client does not support WPS.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page.Step 2: After selecting Auto, the following page will appear. There are two ways to add a wireless device, that supports WPS. Firstly, there is the Personal  Identication Number  (PIN)  method. Using  this method will prompt the user to enter a PIN code. This PIN code should be identical on the wireless client. Secondly, there is the Push Button Conguration (PBC)  method.  Using  this  method  will  allow  the  wireless  client  to connect to this device by similarly pressing the PBC button on it.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page.
Section 3 - Software CongurationStep 2: After selecting Manual, the following page will appear. On this page  to  user  can  view  the  wireless  conguration  of  this  router.  The wireless clients should congure their wireless settings to be identical to the settings displayed on this page for a successful connection. This option is for wireless clients that can’t use the WPS method to connect to this device.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page. Click on the Wireless Status button to navigate to the Status > Wireless page to view what wireless client are connected to this device.Wireless Settings: Manual Wireless Network SetupThe  manual  wireless  network  setup  option  allows  users  to  congure the wireless settings of this device manually. This option is for the more advanced user and includes all parameters that can be congured for wireless connectivity.To initiate the Manual Wireless  Setup page, click on the Manual Wireless Connection Setup button.On this page the user can congure all the parameters related to the wireless connectivity of this router.
Section 3 - Software CongurationThe  following  parameters  will  be  available  for  wireless  distribution system (WDS) conguration:Enable WDS: Check  the  box  to  enable  the  WDS  function.  If you  do  not  want  to  use  WDS,  uncheck  the  box to disable the service. Select the time frame that you would  like  your WDS enabled. The schedule may be set to Always. Any schedule you create will be  available  in  the  drop-down  menu.  Click  New Schedule to create a new schedule.Wi-Fi Network Name: The  Service  Set  Identier  (SSID)  is  the  name  of your wireless network. Click Site Survey to select an existing SSID or create a name using up to 32 characters. The SSID is case-sensitive.Security Mode: Select  either  WEP  or  WPA-Personal  for  security encryption.
Section 3 - Software CongurationThe following parameters will be available for conguration:Wireless Band: Displays  the  wireless  band  being  congured.  In this option we nd that the following parameters will be regarding the 2.4GHz band.Enable Wireless:  Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Select the time frame that you would like  your wireless  network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a new schedule.Wireless Network Name:The  Service  Set  Identier  (SSID)  is  the  name  of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. 802.11 Mode: Here the user can manually select the preferred frequency band to use for this wireless network.Enable Auto Channel Scan:The auto  channel  selection  setting  can  be  selected to allow  this  device  to  choose  the  channel  with  the  least amount of interference.Wireless Channel:By default the channel is set to 1. The Channel can be changed to t the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Selection, this option will be greyed out.Transmission Rate:Select the transmit rate. It is strongly suggested to select Best (Automatic) for best performance.Channel Width: When using the 802.11n frequency band, the user have an option to choose between a 20MHz or 20/40MHz bandwidth.Visibility Status: The Invisible option allows you to hide your wireless network. When this option is set to Visible, your wireless network name is broadcasted to anyone within the range of your signal. If you are not using encryption then they could connect to your network. When Invisible mode is enabled, you must enter the Wireless Network Name (SSID) on the client manually to connect to the network.
Section 3 - Software CongurationBy  default  the  wireless security  of  this  router will be  disabled. In  this next  option  the  user  can  enabled  or  disable  wireless  security  for  the frequency band 2.4GHz. There are two types of encryption that can be used-  WEP or WPA/WPA2.Wireless Security Mode: WEPWired  Equivalent  Privacy  (WEP)  is  the  most  basic  form  of  encryption that can be used for wireless networks. Even though it is known as a ‘weak’ security method, it is better than no security at all. Older wireless adapter sometimes only supports WEP encryption and thus we still nd this encryption method used today.WEP Key Length: Here the user can specify to either use a 64Bit or a 128Bit encrypted key.Authentication: Authentication  is  a  process  by  which  the  router veries  the  identity  of  a  network  device  that  is attempting  to  join  the  wireless  network.  There are two types authentication for this device when using WEP. Open System allows all wireless devices to  communicate with  the  router before  they  are required to provide the encryption key needed to gain access to the  network. Shared Key requires any  wireless  device  attempting  to  communicate with  the  router  to  provide  the  encryption  key needed  to  access  the  network  before  they  are allowed to communicate with the router.WEP Key 1: Enter the WEP key used here. For 64-bit keys you must enter 10 hex digits into each key box. For 128-bit keys you must enter 26 hex digits into each key box. A hex digit is either a number from 0 to 9 or a letter from A to F. You may also enter any text string into a WEP key box, in which case it will be converted into a hexadecimal key using the ASCII values of the characters. A maximum of 5 text characters can be entered for 64-bit keys, and a maximum of 13 characters for 128-bit keys.
Section 3 - Software CongurationWireless Security Mode: WPA-PersonalWi-Fi  Protected  Access  (WPA)  is  the  most  advanced  and  up  to  date wireless  encryption  method  used  today.  This  is  the  recommended wireless security option. WPA supports two authentication frameworks. Personal (PSK) and Enterprise (EAP). Personal requires only the use of a pass-phrase (Shared Secret) for security. The following parameters will be available for conguration:WPA Mode: WPA  is  the  older  standard;  select  this  option  if the clients that will be used with the router only support  the  older  standard.  WPA2  is  the  newer implementation  of  the  stronger  IEEE  802.11i security  standard.  With  the  “WPA2”  option,  the router tries WPA2 rst, but falls back to WPA if the client  only  supports  WPA.  With  the “WPA2  Only” option, the router associates only with clients that also support WPA2 security.Cipher Type: Select  the  appropriate  cipher  type  to  use  here. Options to choose from are Temporal Key Integrity Protocol  (TKIP),  Advanced  Encryption  Standard (AES), and Both (TKIP and AES).Group Key Update Interval:Enter  the  amount  of  time  before  the  group  key used for broadcast and multicast data is changed.Pre-Shared Key: Enter  the  shared  secret  used  here.  This  secret phrase needs to be the same on all of the wireless clients  for  them  to  be  able  to  connect  to  the wireless network successfully.
Section 3 - Software CongurationWireless Security Mode: WPA-EnterpriseWi-Fi  Protected  Access  (WPA)  is  the  most  advanced  and  up  to  date wireless  encryption  method  used  today.  This  is  the  recommended wireless security option. WPA supports two authentication frameworks. Personal (PSK) and Enterprise (EAP). Personal requires only the use of a pass-phrase (Shared Secret) for security. WPA Mode: WPA  is  the  older  standard;  select  this  option  if the clients that will be used with the router only support  the  older  standard.  WPA2  is  the  newer implementation  of  the  stronger  IEEE  802.11i security  standard.  With  the  “WPA2”  option,  the router tries WPA2 rst, but falls back to WPA if the client  only  supports  WPA.  With  the “WPA2  Only” option, the router associates only with clients that also support WPA2 security.Cipher Type: Select  the  appropriate  cipher  type  to  use  here. Options to choose from are Temporal Key Integrity Protocol  (TKIP),  Advanced  Encryption  Standard (AES), and Both (TKIP and AES).Group Key Update Interval:Enter  the  amount  of  time  before  the  group  key used for broadcast and multicast data is changed.RADIUS Server IP Address:When  the  user  chooses  to  use  the  EAP authentication framework, the RADIUS server’s IP address can be entered here.RADIUS Server Port:When  the  user  chooses  to  use  the  EAP authentication  framework,  the  RADIUS  server’s port number can be entered here.RADIUS Server Shared Secret:Enter  the  shared  secret  used  here.  This  secret phrase needs to be the same on all of the wireless clients  for  them  to  be  able  to  connect  to  the wireless network successfully.
Section 3 - Software CongurationNetwork SettingsRouter IP Address:Enter the  IP  address of the  router. The default  IP address is 192.168.0.1. If you change the IP address, once you click  Apply,  you will  need  to  enter  the new IP address in  your  browser to get  back  into the conguration utility.Default Subnet Mask:Enter the Subnet Mask. The default subnet mask is 255.255.255.0.Host Name: Enter a Host Name to identify this device.Local Domain Name:Enter the local domain name used here. (Optional).Enable DNS Relay:Uncheck  the  box  to  transfer  the  DNS  server information  from  your  ISP  to  your  computers.  If checked, your computers will use the router for a DNS server.DHCP Server SettingsDHCP stands for Dynamic Host Control Protocol. This device has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the router. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.On this page the user can congure the internal network settings of the router and also able to congure the built-in DHCP server to assign IP addresses to computers on the network. The IP address that is congured here is the IP address that is used to access the Web-based management interface. If you change the IP address in this section, you may need to adjust your PC’s network settings to access the network again.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable DHCP Server:Check this box to enable the DHCP server on your router. Uncheck to disable this function.DHCP IP Address Range:Enter the starting and ending IP addresses for the DHCP server’s IP assignment.DHCP Lease Time:The length of time for the IP address lease. Enter the Lease time in minutes.Always Broadcast:If all the computers on the LAN successfully obtain their  IP  addresses from  the  router’s  DHCP  server as  expected,  this  option  can  remain  disabled. However,  if  one  of  the  computers  on  the  LAN fails  to  obtain  an  IP  address  from  the  router’s DHCP server, it may have an old DHCP client that incorrectly  turns  o  the  broadcast  ag  of  DHCP packets. Enabling this option will cause the router to  always  broadcast  its  responses  to  all  clients, thereby working around the problem, at the cost of increased broadcast trac on the LAN.NetBIOS announcement:Check this box to allow the DHCP Server to oer NetBIOS conguration settings to the LAN hosts. NetBIOS  allow  LAN  hosts  to  discover  all  other computers within the network, e.g. within Network Neighborhood.Learn NetBIOS from WAN:If NetBIOS announcement is switched on, it will cause WINS information to be learned from the WAN side, if available. Turn this setting o to congure manually.NetBIOS Scope: This is an advanced setting and is normally left blank. This allows the conguration of a NetBIOS ‘domain’ name under which network hosts operate. This setting has no eect if the ‘Learn NetBIOS information from WAN’ is activated.
Section 3 - Software CongurationNetBIOS node type:This eld indicates how network hosts are to perform NetBIOS name registration and discovery. H-Node, this indicates a Hybrid-State of operation. First WINS servers are tried, if any, followed by local network broadcast. This is generally the preferred mode if you have congured WINS servers. M-Node (default), this indicates a Mixed-Mode of operation. First Broadcast operation is performed to register hosts and discover other hosts, if broadcast operation fails, WINS servers are tried, if any. This mode favours broadcast operation which may be preferred if WINS servers are reachable by a slow network link and the majority of network services such as servers and printers are local to the LAN. P-Node, this indicates to use WINS servers ONLY. This setting is useful to force all NetBIOS operation to the congured WINS servers. You must have congured at least the primary WINS server IP to point to a working WINS server. B-Node, this indicates to use local network broadcast ONLY. This setting is useful where there are no WINS servers available, however, it is preferred you try M-Node operation rst. This setting has no eect if the ‘Learn NetBIOS information from WAN’ is activated.Primary WINS Server IP address:Congure the IP address of the preferred WINS server. WINS Servers store information regarding network hosts, allowing hosts to ‘register’ themselves as well as discover other available hosts, e.g. for use in Network Neighborhood. This setting has no eect if the ‘Learn NetBIOS information from WAN’ is activated.Secondary WINS Server IP address:Congure the IP address of the backup WINS server, if any. This setting has no eect if the ‘Learn NetBIOS information from WAN’ is activated.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable: Check this box to enable the reservation.Computer Name: Enter  the  computer  name.  Alternatively,  select  a computer  that  currently  has  a  DHCP  lease  from the drop down menu and click << to automatically populate  the  Computer  Name,  IP  Address,  and MAC Address elds.IP Address: Enter  the  IP  address  you  want  to  assign  to  the computer  or  device.  This  IP  Address  must  be within the DHCP IP Address Range.MAC Address: Enter the MAC address of the computer or device.DHCP Reservations ListThis  shows  clients  that  you  have  specied  to  have  reserved  DHCP addresses. An entry can be changed by clicking the Edit icon, or deleted by clicking  the  Delete  icon. When you  click  the  Edit  icon,  the  item  is highlighted,  and  the ‘Edit  DHCP  Reservation’  section  is  activated  for editing.Number of Dynamic DHCP ClientsIn  this section  you can  see  what LAN  devices  are currently leasing  IP addresses.Add/Edit DHCP ReservationThis option lets you reserve IP addresses, and assign the same IP address to the network device with the specied MAC address any time it requests an IP address. This is almost the same as when a device has a static IP address except that the device must still request an IP address from the D-Link router. The D-Link router will provide the device the same IP address every time. DHCP Reservations are helpful for server computers on the local network that are hosting applications such as Web and FTP. Servers on your network should either use a static IP address or use this option.
Section 3 - Software CongurationIPv6On this page, the user can congure the IPv6 Connection type. There are two ways to set up the IPv6 Internet connection. You can use the Web-based IPv6 Internet Connection Setup Wizard, or you can manually congure the connection.IPv6 Internet Connection Setup WizardFor  the  beginner  user  that  have not  congured a router before,  click on the IPv6 Internet Connection Setup Wizard button and the router will guide you through a few simple steps to get your network up and running. After clicking on the IPv6 Internet Connection Setup Wizard button, this page will appear.Welcome to the D-Link IPv6 Internet Connection Setup WizardThis wizard will guide you through a step-by-step process to congure your new D-Link router and connect to the IPv6 Internet.Click  Next  to  continue  to  the  next  page.  Click  Cancel  to  discard  the changes made and return to the main page.
Section 3 - Software CongurationStep 1: Congure Your IPv6 Internet ConnectionThe router will try and detect whether its possible to obtain the IPv6 Internet Connection type automatically. If this succeeds then the user will be guided through the input of the appropriate parameters for the connection type found.However,  if  the  automatic  detection  fails,  the  user  will  be  prompt  to either Try again or to click on the Guide me through the IPv6 settings button to initiate the manual continual of the wizard.
Section 3 - Software CongurationStep 1: Congure Your IPv6 Internet ConnectionThere are several  connection types to choose from. If  you are unsure of your connection method, please contact your IPv6 Internet Service Provider. Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled. The 3 options available on this page is IPv6 over PPPoE, Static IPv6 address and Route, and Tunneling Connection. Choose  the  required  IPv6  Internet  Connection  type  and  click  on  the Next  button  to  continue.  Click  on  the  Prev  button  to  return  to  the previous page. Click  on  the  Cancel button to  discard all  the  changes made and return to the main page.Set Username and Password Connection (PPPoE)After  selecting  the  IPv6  over  PPPoE  option,  the  user  will  be  able  to congure the IPv6 Internet connection that requires a username and password to get online. Most DSL modems use this type of connection.The following parameters will be available for conguration:PPPoE Session: Select  the  PPPoE  Session  value  used  here.  This option  will  state  that  this  connection  shares  it’s information  with  the  already  congured  IPv6 PPPoE  connection,  or  the  user  can  create a  new PPPoE connection here.User Name: Enter  the  PPPoE  username  used  here.  This information is obtainable from the ISP.Password: Enter  the  PPPoE  password  used  here.  This information is obtainable from the ISP.Verify Password: Re-enter the PPPoE password used here.Service Name: Enter the service name for this connection here. This option is optional.Click on the Next button to continue. Click on the Prev button to return to the previous page.Click on the Cancel button to discard all the changes made and return to the main page.
Section 3 - Software CongurationUse Link-Local Address:The  Link-local  address  is  used  by  nodes  and routers  when  communicating  with  neighboring nodes on the same link. This mode enables IPv6-capable devices to communicate with each other on the LAN side.IPv6 Address: Enter the WAN IPv6 address for the router here.Subnet Prex Length:Enter  the  WAN  subnet  prex  length  value  used here.Set Static IPv6 Address ConnectionThis mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your IPv6 conguration settings. You must enter the IPv6 address, Subnet Prex Length, Default Gateway, Primary DNS Server, and Secondary DNS Server. Your ISP provides you with all this information.Click on the Next button to continue. Click on the Prev button to return to the previous page.Click on the Cancel button to discard all the changes made and return to the main page.Default GatewayPrimary IPv6 DNS Address:Secondary IPv6 DNS Address:LAN IPv6 Address:Enter the WAN default gateway IPv6 address used here.Enter the WAN primary DNS Server address used here.Enter the WAN secondary DNS Server address used here.These are the settings of the LAN (Local Area Network) IPv6 interface for the router. The router’s LAN IPv6 Address conguration is based on the IPv6 Address and Subnet assigned by your ISP. (A subnet with prex /64 is supported in LAN.)
Section 3 - Software CongurationTunneling Connection (6rd)After  selecting  the  Tunneling  Connection  (6rd)  option,  the  user  can congure the IPv6 6rd connection settings.The following parameters will be available for conguration:6rd IPv6 Prex: Enter the 6rd IPv6 address and prex value used here.IPv4 Address: Enter the IPv4 address used here.Mask Length: Enter the IPv4 mask length used here.Assigned IPv6 Prex:Displays the IPv6 assigned prex value here.6rd Border Relay IPv4 Address:Enter the 6rd border relay IPv4 address used here.IPv6 DNS Server: Enter the primary DNS Server address used here.Click on the Next button to continue. Click on the Prev button to return to the previous page.Click on the Cancel button to discard all the changes made and return to the main page.Setup CompleteThe IPv6 Internet Connection Setup Wizard was completed. Click on the Connect button to continue. Click on the Prev button to return to the previous page. Click on the Cancel button to discard all the changes made and return to the main page.
Section 3 - Software CongurationManual IPv6 Internet Connection OptionFor  the  advanced user  that  have congured  a  router before,  click  on the  Manual  IPv6  Internet  Connection  Setup  button  to  input  all  the settings manually.On  this  page  the  user  can  manually  congure  the  mode  that  the Router will use to access an IPv6 Internet connection. There are several connection  types  to  choose  from:  Link-local,  Static  IPv6,  DHCPv6, Stateless Auto-Conguration, PPPoE, IPv6  over IPv4 Tunnel  and  6to4. If you are unsure of your connection method, please contact your IPv6 ISP.IPv6 Connection Type: Auto DetectionIn  the  following  section  we’ll  discuss  the  parameters  that  can  be congured  when  setting  up  an  Auto  Detection  (Stateless/DHCPv6) connection. This is a method of connection where the ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some ISP’s require you to make some settings on your side before your router can connect to the IPv6 Internet.Obtain IPv6 DNS Server automatically:Select  this  option  to  obtain  the  DNS  Server addresses automatically.Use the following IPv6 DNS Servers:Select  this  option  to  manually  enter  the  DNS Server addresses used.Primary DNS: Enter the primary DNS Server address used here.Secondary DNS: Enter  the  secondary  DNS  Server  address  used here.
Section 3 - Software CongurationUse the section to congure the internal network settings of your router. The LAN IPv6 Link-Local Address is the IPv6 Address that you use to access the Web-based management interface. If you change the LAN IPv6 Address here, you may need to adjust your PC’s network settings to access the network again. DHCP-PD can be used to acquire a IPv6 prex for the LAN interface.Enable DHCP-PD:Select this option to enable DHCP PD.LAN IPv6 Address:Enter the LAN IPv6 address used here. This address must be in the ‘/64’ subnet.LAN IPv6 Link-Local Address:Displays  the  LAN  IPv6  Link-Local  address  used here.The following parameters will be available for conguration:Enable Automatic IPv6 address:The user can tick this option to enable the auto-conguration feature.Enable Automatic DHCP-PD in LAN:AutocongurationTick this option to enable the automatic DHCP-PD on the LAN.Autoconguration Type:The  user  can  select  the  auto-conguration  type used here. Router Advertisement Lifetime:This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateless.  Enter  the router advertisement lifetime value used here.
Section 3 - Software CongurationIPv6 Address Range (Start):This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateful.  Enter  the start IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Range (End):This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the end IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the IPv6 Address Lifetime (in minutes).Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationIPv6 Connection Type: Static IPv6In the following section we’ll discuss the parameters that can be congured when setting up an Static IPv6 connection. This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your IPv6 conguration settings. You must enter the IPv6 address, Subnet Prex Length, Default Gateway, Primary DNS Server, and Secondary DNS Server. Your ISP provides you with all this information.The following parameters will be available for conguration:Use Link-Local Address:The  Link-local  address  is  used  by  nodes  and routers  when  communicating  with  neighboring nodes on the same link. This mode enables IPv6-capable devices to communicate with each other on the LAN side.IPv6 Address: Enter the WAN IPv6 address for the router here.Subnet Prex Length:Default Gateway:Enter the WAN default gateway IPv6 address used here.Primary DNS Server:Secondary DNS Servers:Enter  the  WAN  primary  DNS  Server  address  used here.Enter the WAN secondary DNS Server address used here.
Section 3 - Software CongurationThe following parameters will be available for conguration:LAN IPv6 Address:Enter  the  LAN  (local)  IPv6  address  for  the  router here.LAN IPv6 Link-Local Address:Displays the Router’s LAN Link-Local Address here.The following parameters will be available for conguration:Enable Automatic IPv6 address:The user can tick this option to enable the auto-conguration feature.Autoconguration Type:The user can select the auto-conguration type used here. Router Advertisement Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateless. Enter the router advertisement lifetime value used here.IPv6 Address Range (Start):This  option  is  only  available  when  the  auto-conguration type  is  set  to Stateful. Enter the start  IPv6  Address  for  the  DHCPv6  range  for your local computers.IPv6 Address Range (End):This  option  is  only  available  when  the  auto-conguration type  is  set  to Stateful. Enter the end IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Lifetime:This  option  is  only  available  when  the  auto-conguration type  is  set  to Stateful. Enter the IPv6 Address Lifetime (in minutes).Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationIPv6 Connection Type: Autoconguration (SLAAC/DHCPv6)In the following section we’ll discuss the parameters that can be congured when setting up an Autoconguration (SLAAC/DHCPv6) connection. This is a method of connection where the ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some ISP’s require you to make some settings on your side before your router can connect to the IPv6 Internet.The following parameters will be available for conguration:Obtain IPv6 DNS Servers automatically:Select  this  option  to  obtain  the  DNS  Server addresses automatically.Use the following IPv6 DNS Servers:Select  this  option  to  manually  enter  the  DNS Server addresses used. Primary DNS Server:Enter the WAN primary DNS Server address used here.Secondary DNS Server:Enter  the  WAN  secondary  DNS  Server  address used here. Enable DHCP-PD:LAN IPv6 Address:LAN IPv6 Link-Local Address:Select this option to enable DHCP PD.Enter the LAN IPv6 address used here. This address must be in the ‘/64’ subnet.Displays  the  LAN  IPv6  Link-Local  address  used here.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable Automatic IPv6 address:The user can tick this option to enable the auto-conguration feature.Enable Automatic DHCP-PD in LAN:Tick this option to enable the automatic DHCP-PD on the LAN.Autoconguration Type:The user can select the auto-conguration type used here. Router Advertisement Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateless. Enter the router advertisement lifetime value used here.IPv6 Address Range (Start):This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateful.  Enter  the start IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Range (End):This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateful.  Enter  the end IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Lifetime:This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateful.  Enter  the IPv6 Address Lifetime (in minutes).Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationIPv6 Connection Type: PPPoESelect this option if your ISP requires you to use a PPPoE (Point to Point Protocol over Ethernet) connection to IPv6 Internet. DSL providers typically use this option. This method of connection requires you to enter a Username and Password (provided by your Internet Service Provider) to gain access to the IPv6 Internet. The supported authentication protocols are PAP and CHAP.The following parameters will be available for conguration:PPPoE Session: Select  the  PPPoE  Session  value  used  here.  This option  will  state  that  this  connection  shares  it’s information  with  the  already  congured  IPv6 PPPoE  connection,  or  the  user  can  create a  new PPPoE connection here.Address Mode: Select  the  appropriate  address  mode  used  here. Select  Dynamic  IP  if  the  ISP’s  servers  assign  the router’s  WAN  IPv6  address  upon  establishing  a connection.  If your ISP has  assigned  a  xed  IPv6 address, select Static IP. The ISP provides the value for the IPv6 Address.IP Address: Enter the ISP PPPoE IP address in here.Username: Enter the PPPoE username used here. This information is obtainable from the ISP.Password: Enter the PPPoE password used here. This information is obtainable from the ISP.Verify Password: Re-enter the PPPoE password used here.Service Name: Enter the service name for this connection here. This option is optional.MTU: Enter the MTU value used here. The default value is 1492.
Section 3 - Software CongurationThe following parameters will be available for conguration:Obtain IPv6: Select  this  option  to  obtain  the  DNS  Server addresses automatically.Use IPv6: Select  this  option  to  manually  enter  the  DNS Server addresses used.Primary DNS: Enter the primary DNS Server address used here.Secondary DNS: Enter  the  secondary  DNS  Server  address  used here.The following parameters will be available for conguration:Enable DHCP-PD:Select this option to enable DHCP PD.LAN IPv6 Address:Enter the LAN IPv6 address used here. This address must be in the ‘/64’ subnet.LAN IPv6 Link-Local Address:Displays  the  LAN  IPv6  Link-Local  address  used here.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable Automatic IPv6 address:The  user  can  tick  this  option  to  enable  the auto-conguration feature.Enable Automatic DHCP-PD in LAN:Tick this option to enable the automatic DHCP-PD on the LAN.Autoconguration Type:The  user  can  select  the  auto-conguration type used here. Router Advertisement Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateless. Enter the router advertisement lifetime value used here.IPv6 Address Range (Start):This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the start  IPv6  Address  for  the  DHCPv6  range  for your local computers.IPv6 Address Range (End):This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the end  IPv6  Address  for  the  DHCPv6  range  for your local computers.IPv6 Address Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the IPv6 Address Lifetime (in minutes).Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationIPv6 Connection Type: IPv6 in IPv4 TunnelIn section to the user can congure the IPv6 connection to run in IPv4 Tunnel  mode.  IPv6  over  IPv4  tunneling  encapsulates  IPv6  packets  in IPv4 packets so that IPv6 packets can be sent over an IPv4 infrastructure.The following parameters will be available for conguration:Remote IPv4 Address:Enter the remote IPv4 address used here.Remote IPv6 Address:Enter the remote IPv6 address used here.Local IPv4 Address:Enter the local IPv4 address used here.Local IPv6 Address:Enter the local IPv6 address used here.Subnet Prex Length:Enter the Subnet prex length value used here.The following parameters will be available for conguration:Obtain IPv6 DNS Servers automatically:Select  this  option  to  obtain  the  DNS  Server addresses automatically.Use the following IPv6 DNS Servers:Select  this  option  to  manually  enter  the  DNS Server addresses used.Primary DNS Server:Enter the WAN primary DNS Server address used here.Secondary DNS Server:Enter the WAN secondary DNS Server address used here.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable DHCP-PD:Select this option to enable DHCP PD.LAN IPv6 Address:Enter the LAN IPv6 address used here. This address must be in the ‘/64’ subnet.LAN IPv6 Link-Local Address:Displays  the  LAN  IPv6  Link-Local  address  used here.The following parameters will be available for conguration:Enable Automatic IPv6 address:The user can tick this option to enable the auto-conguration feature.Enable Automatic DHCP-PD in LAN:Tick this option to enable the automatic DHCP-PD on the LAN.Autoconguration Type:The user can select the auto-conguration type used here. Router Advertisement Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateless. Enter the router advertisement lifetime value used here.IPv6 Address Range (Start):This  option  is  only  available  when  the  auto-conguration type  is  set  to  Stateful.  Enter  the start IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Range (End):This  option  is  only  available  when  the  auto-conguration type  is  set  to  Stateful.  Enter  the end IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Lifetime:This  option  is  only  available  when  the  auto-conguration type  is  set  to  Stateful.  Enter  the IPv6 Address Lifetime (in minutes).Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationIPv6 Connection Type: 6to4In this section the user can congure the IPv6 6to4 connection settings. 6to4 is an IPv6 address assignment and automatic tunneling technology that used to provide unicast IPv6 connectivity between IPv6 sites and hosts across the IPv4 Internet.The following parameters will be available for conguration:6to4 Address: Here the 6to4 congured address will be displayed.6to4 Relay: Enter the 6to4 relay address used here.Primary DNS Server:Enter the primary DNS Server address used here.Secondary DNS Server:Enter  the  secondary  DNS  Server  address  used here.The following parameters will be available for conguration:LAN IPv6 Address:Enter the LAN IPv6 address used here. This address must be in the ‘/64’ subnet.LAN IPv6 Link-Local Address:Displays  the  LAN  IPv6  Link-Local  address  used here.Enable Automatic IPv6 addressAutoconguration Type:Router Advertisement Lifetime:The  user  can  tick  this  option  to  enable  the  auto-conguration feature.The  user  can  select  the  auto-conguration  type used here. This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateless.  Enter  the router advertisement lifetime value used here
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable Automatic IPv6 address:The user can tick this option to enable the auto-conguration feature.Autoconguration Type:The user can select the auto-conguration type used here. IPv6 Address Range (Start):This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateful.  Enter  the start IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Range (End):This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateful.  Enter  the end IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Lifetime:This  option  is  only  available  when  the  auto-conguration  type  is  set  to  Stateful.  Enter  the IPv6 Address Lifetime (in minutes).Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationIPv6 Connection Type: 6rdIn this section the user can congure the IPv6 6rd connection settings.The following parameters will be available for conguration:6rd Conguration:Select the desired 6rd conguration option here. 6rd IPv6 Prex: Enter the 6rd IPv6 address and prex value used here.IPv4 Address: Enter the IPv4 address used here.Mask Length: Enter the IPv4 mask length used here.Assigned IPv6 Prex:Displays the IPv6 assigned prex value here.6rd Border Relay IPv4 Address:Enter the 6rd border relay IPv4 address used here.Primary DNS ServerEnter the primary DNS Server address used here.Secondary DNS Server:Enter the secondary DNS Server address uses here.The following parameters will be available for conguration:LAN IPv6 Address:Enter the LAN IPv6 address used here.  This address must be in the ‘/64’ subnet.LAN IPv6 Link-Local Address:Displays  the  LAN  IPv6  Link-Local  address  used here.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable Automatic IPv6 address:The user can tick this option to enable the auto-conguration feature.Autoconguration Type:The user can select the auto-conguration type used here. Router Advertisement Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateless. Enter the router advertisement lifetime value used here.IPv6 Address Range (Start):This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the start  IPv6  Address  for  the  DHCPv6  range  for your local computers.IPv6 Address Range (End):This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the end IPv6 Address for the DHCPv6 range for your local computers.IPv6 Address Lifetime:This  option  is  only  available  when  the  auto-conguration type is set to Stateful. Enter the IPv6 Address Lifetime (in minutes).Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationIPv6 Connection Type: Local Connection OnlyThe Link-local address is used by nodes and routers when communicating with  neighboring  nodes  on  the  same  link.  This  mode  enables  IPv6-capable devices to communicate with each other on the LAN side.The following parameters will be available for conguration:LAN IPv6 Link-Local  Address:Displays  the  LAN  IPv6  Link-Local  address  used here.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationAdvanced CategoryThis section allows the user to congure the more advanced features that can be done by this router. Features like Port Forwarding, Firewall settings, Quality of Service settings and more.
Section 3 - Software CongurationVirtual ServerThis router can be congured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The router’s rewall feature lters out unrecognized packets to protect the LAN network so all computers networked with the router are invisible to the outside world. The user can make some of the LAN computers accessible from the Internet by enabling Virtual Server. Depending on the requested service, the router redirects the external service request to the appropriate server within the LAN network. The router is also capable of port-redirection, meaning that incoming trac to a particular port may be redirected to a dierent port on the server computer.Checkbox: Check the box on the left side to enable the Virtual Server rule.Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the elds.IP Address: Enter the IP address of the computer on your local network  that  you  want  to  allow  the  incoming service  to.  If  your  computer  is  receiving  an  IP address  automatically  from  the  router  (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<.
Section 3 - Software CongurationPort: Enter the port that you want to open next to Public Port and Private Port. The public and private ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network.Trac Type: Select TCP, UDP, or All from the Protocol drop-down menu.Schedule: Use the  drop-down menu to  schedule the time  that  the Virtual  Server Rule will  be  enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Schedules page.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationPort ForwardingThe Port Forwarding option gives Internet users access to services on your LAN. This feature is useful for hosting online services such as FTP, Web or game servers. For each entry, you dene a public port on your router for redirection to an internal LAN IP Address and LAN port. This option is used to open multiple ports or a range of ports in your router and redirect data through those ports to a single PC on your network. This feature allows you to enter ports in the format, Port Ranges (100-150),  Individual Ports (80, 68, 888), or Mixed (1020-5000, 689). This option is only applicable to the INTERNET session.The following parameters will be available for conguration:Checkbox: Tick the  checkbox on  the  left  side  to  enable  the Port Forwarding rule.Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the elds.IP Address: Enter the IP address of the computer on your local network  that  you  want  to  allow  the  incoming service  to.  If  your  computer  is  receiving  an  IP address  automatically  from  the  router  (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<.Ports to Open: Enter the external port number in the appropriate space provided. If the port number is TCP then enter the number in the TCP space, and if the port number is UDP than enter it in the UDP space.Schedule: Use the drop-down menu to schedule the time that the Port Forwarding rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Schedules page.Inbound Filter: Select the inbound lter rule here. Options to choose from are Allow All, Deny All, and any other custom rule created.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationApplication RulesSome applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have diculties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the router. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port” eld, select the protocol type as TCP or UDP, then enter the rewall (public) ports associated with the trigger port to open them for inbound trac.The following parameters will be available for conguration:Checkbox: Check  the  box  on  the  left  side  to  enable  the Application Rule.Name: Enter  a  name  for  the  rule.  You  may  select  a predened  application  from  the  Application drop-down menu and click <<.Application: Displays a list of predened application to use in the rules.Port (Trigger): This is the port used to trigger the application. It can be either a single port or a range of ports.Port (Firewall): This is the port number on the Internet side that will  be  used  to  access  the  application.  You  may dene a single port or a range of  ports. You can use a comma to add multiple ports or port ranges.Trac Type: Select the protocol of the rewall port (TCP, UDP, or All).Schedule: The schedule of time when the Application Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Schedules page.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationQoS EngineThe QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classied automatically. The QoS section contains a queuing mechanism, trac shaping and classication. It  supports  two kinds of  queuing  mechanisms. Strict Priority Queue (SPQ)  and Weighted Fair Queue (WFQ). SPQ  will  process trac based on trac priority. Queue1 has the highest priority and Queue4 has the lowest priority. WFQ will process trac based on the queue weight. Users can congure each queue’s weight. The sum of all the queue’s weight must be 100. When surng the Internet, the system will do trac shaping based on the uplink and downlink speed. The classication rules can be used to classify trac to dierent queues, then SPQ or WFQ will do QoS based on the queue’s priority or weight.Enable QoS: This  option  is  disabled  by  default.  Enable  this option for better performance and experience with online  games  and  other  interactive  applications, such as VoIP.Uplink Speed: The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISP’s often dene speed as a download/upload pair.  For  example,  1.5Mbits/284Kbits.  Using  this example, you would enter 284.  Alternatively you can test your uplink speed with a service such as www.dslreports.com.Downlink Speed: The speed at which data can be transferred from the ISP to the router. This  is determined by your ISP. ISP’s often dene speed as a download/upload pair. For example, 1.5Mbits/284Kbits. Using this  example, you would enter 1500.  Alternatively you  can  test your downlink speed  with  a  service  such  as  www.dslreports.com.Queue Type: Here the user can specify the queue type used. When choosing the option Strict Priority Queue, the router will apply QoS based on the internal specication for the queue ID’s listed. When choosing the option Weight Fair Queue, the router will apply QoS based on the user dened percentage in the Queue Weight column.Queue ID: In this column the Queue ID used will be displayed.Queue Priority: In this column the Queue Priority used will be displayed.Queue Weight: After choosing to use the Weight Fair Queue option, under Queue Type, the user will be able to manual enter the Queue Weight for each individual Queue ID.
Section 3 - Software CongurationThe following parameters will be available for conguration:Checkbox: Tick this option to enable the rule specied.Name: Enter  a  custom  name  for  the  rule  being  created here. This name is used for identication.Queue ID: Select  the appropriate priority requirement  from the drop-down menu that will be applied to this rule. Option  to  choose  from  are  Highest,  Higher, Normal, and Best Eort.Protocol: Select  the  protocol  used  for  the  application  for in the drop-down menu and it will automatically place it in the Protocol eld.Local IP Range: Enter  the  local  IP  range  used  here. This  is  the  IP range of you Local Area Network. The Router’s IP cannot be included in this range.Remote IP Range:Enter  the  remote  IP  range  used  here. This is  the IP range of the public network from the Internet Port  side.  To  apply  this  rule  to  any  IP  addresses from  the  public  side,  enter  the  range  0.0.0.1  to 255.255.255.254.Application Port: Enter the application port number used here.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.After specifying the QoS framework used, in the QoS setup section, the user can now create individual rules for scenarios that require the use of trac control and data priority manipulation.
Section 3 - Software CongurationNetwork FilterThe MAC (Media Access Controller) Address lter option is used to control network access based on the MAC Address of the network adapter. A MAC address is a unique ID assigned by the manufacturer of the network adapter. This feature can be congured to ALLOW or DENY network/Internet access.In the MAC Filtering Rules section, the user can create and edit Network lter rules. This maximum amount of rules that can be created are 24 rules.The following parameters will be available for conguration:Congure MAC Filtering below:Select Turn MAC Filtering OFF, Turn MAC Filtering ON  and  ALLOW  computers  listed  to  access  the network,  or  Turn  MAC  Filtering  ON  and  DENY computers listed to access the network from the drop-down menu.Checkbox: Check  the  box  on  the  left  side  to  enable  the Network Filter.MAC Address: Enter  the  MAC  address  you  would  like  to  use  in this ltering rule.DHCP Client List: Select  a  DHCP  client  from  the  Computer  Name drop-down menu and click << to copy that MAC Address.Schedule: The schedule of time when the Network Filter will be  enabled. The schedule  may  be  set  to  Always, which will allow the particular service to always be enabled. Click the New Schedule button to create your own times in the Schedules page.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationAccess ControlThe Access Control option allows you to control access in and out of your network. Use this feature as Access Controls to only grant access to approved sites, limit web access based on time or dates, and/or block internet access for applications like P2P utilities or games.The following parameters will be available for conguration:Enable Access Control:Tick  this  option  to  enable  the  Access  Control feature.Add Policy: Click on this button to add a new Access Control Policy.After clicking on the Add Policy button, the add policy wizard will guide you through the step-by-step process in adding a new policy. The rst window explains the process.Throughout this wizard the user will be able to:Click on the Prev button to return to the previous window.Click on the Next button to continue to the next window.Click on the Cancel button to discard the changes made and return to the main Access Control window.Step 1: In the rst step, the user can enter the policy name used.The following parameters will be available for conguration:Policy Name: Enter the new policy name used for this rule here.
Section 3 - Software CongurationStep 2: In the second step, the user can congure the schedule settings for this rule.The following parameters will be available for conguration:Details: Select  the  appropriate  predened  schedule  rule to apply to this rule from the drop-down menu.Step 3: In the third step, the user can congure the address type and IP address of the machines used in this rule.The following parameters will be available for conguration:Address Type: Specify  a machine  with its IP  or MAC address, or select ‘Other  Machines’ for machines  that do not have a policy.IP Address: After  selecting  the  IP  address  type, the  user  can enter  the  IP  address  of  the  machines  used  in this rule here. Alternatively, the user can select a Computer from the Computer Name list.Machine Address:After  selecting  the  MAC  address  type,  the  user can enter the MAC address of the machine used in this rule here. Alternatively, the used can select a Computer from the Computer Name list.Add: Click on this button to add the machine to the list.Update: After clicking the   option, the user will be able to update the machine information.Delete: If the user chooses to remove a machine from the list, click on the   icon.Step 4: In the fourth step, the user can select the ltering method used for this rule.The following parameters will be available for conguration:Method: Here the user can select the ltering method used. Options to choose from are ‘Log Web Access Only’, ‘Block All Access’, and ‘Block Some Access’.
Section 3 - Software CongurationThe following parameters will be available for conguration:Apply Web Filter: After  selecting  the  ‘Block  Some  Access’  option, the user will be able to select this option. Selecting this option will allow the web lter access control feature to be applied to this rule.Apply Advanced Port Filters:After  selecting  the ‘Block  Some  Access’    option, the user will be able to select this option. Selecting this  option  will  allow  the  advanced  port  lters access control feature to be applied to this rule.Click on the Save button to accept the changes made and return to the main Access Control window.In the Policy Table section a list on access control rules will be displayed. To edit a specic rule, click on the   icon. To remove a specic rule, click on the   icon.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationWebsite FilterWebsite Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network.Website Filter is used to allow or deny computers on your network from accessing  specic  web  sites  by  keywords  or  specic  Domain  Names. Select ‘ALLOW  computers  access  to  ONLY  these  sites’  in  order  only allow  computers  on  your  network  to  access  the  specied  URLs  and Domain Names. ‘DENY computers access to ONLY these sites’ in order deny  computers  on  your  network  to  access  the  specied  URLs  and Domain Names.The following parameters will be available for conguration:Website URL/Domain:Enter the URL or Domain name that you want to allow or block here.An  example  of  an  URL  is:  http://www.facebook.com/An example of a domain name is: facebook.comClick on the Clear the list below... button to remove all the entries from the spaces in the list.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationInbound FilterThe Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can congure inbound data ltering rules that control data based on an IP address range. Inbound Filters can be used for limiting access to a server on your network to a system or group of systems. Filter rules can be used with Virtual Server, Port Forwarding, or Remote Administration features. The user can add new Inbound lter rule in the next section.The following parameters will be available for conguration:Name: The user can enter a custom name for the inbound lter rule here.Action: Select an action that will take place when this rule is initiated. Options to choose from are Allow and Deny.Enable: Tick this  option  to  enable  the  specied  IP  range for this rule.Remote IP Start: Enter  the  remote  starting  IP  address  here  in  the range.Remote IP End: Enter  the  remote  ending  IP  address  here  in  the range.Add: Click  this  button  to  add  the  new  inbound  lter rule.Cancel: Click this button to discard the new inbound lter rule.In the Inbound Filter Rules List section, the user can view a list of the inbound lter rules already created. To edit a specic rule, click on the  icon. The delete a specic rule, click on the   icon.
Section 3 - Software CongurationFirewall SettingsA rewall protects your network from the outside world. The router oers a rewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.The following parameters will be available for conguration:Enable SPI: Check the Enable SPI box to enable the SPI (Stateful Packet Inspection, also known as dynamic packet ltering)  feature.  Enabling  SPI  helps  to  prevent cyber attacks by tracking more state per session. It  validates  that  the  trac  passing  through  the session conforms to the protocol.The following parameters will be available for conguration:Enable anti-spoof checking:Tick this option to enable the anti-spoof checking feature.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable DMZ: Tick this option to enable the DMZ feature.DMZ IP Address: Enter  the  IP  address  of  the  computer  on  the LAN that you want  to  have unrestricted  Internet communication  in  the  DMZ  IP  address  eld.  To specify an existing DHCP client, use the Computer Name drop-down to select the computer that you want to make a DMZ host. If selecting a computer that  is  a  DHCP  client,  be  sure  to  make  a  static reservation in the Setup > Network Settings page so that the IP address of the DMZ machine does not change.The following parameters will be available for conguration:PPTP: Tick  this  option to allow PPTP access to the LAN network.IPSec (VPN): Tick this option to allow IPSec (VPN) access to the LAN network.RSTP: Tick  this  option  to  allow RSTP access  to the  LAN network.SIP: Tick  this  option  to  allow  SIP  access  to  the  LAN network.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.Firewall rules can be used to allow or deny trac passing through the router. You can specify a single port by utilizing the input box at the top or a range of ports by utilizing both input boxes. DMZ means “Demilitarized Zone”. DMZ allows computers behind the router rewall to be accessible to Internet trac. Typically, your DMZ would contain Web servers, FTP servers and others.
Section 3 - Software CongurationRoutingThe Routing option is an advanced method of customizing specic routes of data through your network.In the Routing List section, the user can congure routing rules used by this router. The maximum amount of rules that can be congured is 32.The following parameters will be available for conguration:Checkbox: To enable a route, check the box that is on the left side of the route.Name: Enter a name for the rule used here.Destination IP: Enter the IP address of the packets that will take this route.Netmask: Enter the netmask to specify the subnet of the IP packets that will take this route.Gateway: Enter the next hop that will be taken if this route is used.Metric: Enter the metric value that this route will use here.Interface: Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the Router.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationAdvanced WirelessThese options are for users that wish to change the behavior of their 802.11n wireless radio from the standard settings. We do not recommend changing these settings from the factory  defaults. Incorrect  settings may impact the  performance of your wireless radio. The default settings should provide the best wireless radio performance in most environments.The following parameters will be available for conguration:Wireless Band: Here  the  user  can  view  the  wireless  frequency band being congured. In the case 2.4GHz.Transmit Power: This  option  sets  the  transmit  power  of  the antennas.WLAN Partition:WMM Enable:Short GI:HT 20/40 Coexistence:Check this box to enable WLAN Partition.Check this box to enable the WMM feature.Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationWi-Fi Protected SetupWi-Fi Protected Setup (WPS) System is a simplied method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certied it across dierent products as well as manufactures. The process is just as easy, as depressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method. The time reduction in setup and ease of use are quite benecial, while the highest wireless Security setting of WPA2 is automatically used.The following parameters will be available for conguration:Enable: Tick  this  option  to  enable  the  Wi-Fi  Protected Setup feature.WiFi Protected Setup:This parameter displays the WPS setup status.Lock Wireless Security Settings:Tick  this  option  to  lock  the  congured  wireless security settings.In the PIN Settings section, the user not only will be able to view the PIN code, but will also be able to reset the PIN to default or to generate a new PIN code. A PIN is a unique number that can be used to add the router to an existing network or to create a new network. The default PIN may be printed on the bottom of the router. For extra security, a new PIN can be generated. You can restore the default PIN at any time. Only the Administrator (“admin” account) can change or reset the PIN.In the Wi-Fi Protected Setup section, the user can enable the WPS feature of this router. The following parameters will be available for conguration:PIN: Shows the current value of the router’s PIN.Reset PIN to Default:Click this button to restore the default PIN of the router.Generate New PIN:Click this button to create a random number that is a valid PIN. This  becomes the router’s PIN. You can then copy this PIN to the user interface of the registrar.Click  the  ‘Connect  your  Wireless  Device’  button  to  start  Wireless Connection Setup Wizard. This wizard helps you add wireless devices to the wireless network.
Section 3 - Software CongurationStep  1:  In  this  step  the  user  have  two  options  to  choose  from. You can choose Auto if the wireless client supports WPS, or Manual if the wireless client does not support WPS.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page.Step 2: After selecting Auto, the following page will appear. There are two ways to add a wireless device, that supports WPS. Firstly, there is the Personal  Identication Number  (PIN)  method. Using  this method will prompt the user to enter a PIN code. This PIN code should be identical on the wireless client. Secondly, there is the Push Button Conguration (PBC)  method.  Using  this  method  will  allow  the  wireless  client  to connect to this device by similarly pressing the PBC button on it.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page.Step 2: After selecting Manual, the following page will appear. On this page  to  user  can  view  the  wireless  conguration  of  this  router.  The wireless clients should congure their wireless settings to be identical to the settings displayed on this page for a successful connection. This option is for wireless clients that can’t use the WPS method to connect to this device.Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page. Click on the Wireless Status button to navigate to the Status > Wireless page to view what wireless client are connected to this device.
Section 3 - Software CongurationAdvanced NetworkThis section contains settings which can change the way the router handles certain types of trac. We recommend that you not change any of these settings unless you are already familiar with them or have been instructed to change them by one of our support personnel.The following parameters will be available for conguration:Enable UPnP: Tick this option to enable the UPnP feature of the router.UPnPUPnP is short for Universal Plug and Play which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. The device is a UPnP enabled router, meaning it will work with other UPnP devices/software. If you do not want to use the UPnP functionality, it can be disabled by selecting “Disabled”.WAN PingWhen you Enable WAN Ping response, you are causing the public WAN (Wide Area Network) IP address on the device to respond to ping commands sent by Internet users. Pinging public WAN IP addresses is a common method used by hackers to test whether your WAN IP address is valid.The following parameters will be available for conguration:Enable WAN Ping Response:Tick this option to enable the WAN Ping Response option of the router.WAN Port SpeedThis allows you to select the speed of the WAN interface of the router. Option to choose from are Auto 10/100/1000Mbps, 10Mbps, 100Mbps, or 1000Mbps.The following parameters will be available for conguration:WAN Port Speed: You  may  set  the  port  speed  of  the  Internet  port to  Auto  10/100/1000Mbps,  10Mbps,  100Mbps, or 1000Mbps. Some older cable or DSL modems may require you to set the port speed to 10Mbps.
Section 3 - Software CongurationMulticast StreamsThis section enables the user to allow IPv4 or IPv6 Multicast trac to pass from the Internet to your network more eciently.The following parameters will be available for conguration:IPv4 Enable Multicast StreamsEnable IPv6 Multicast Streams Enable Multicast Streams:Enable  this  option  if  you  are  receiving  video  on demand  type  of  service  from  the  Internet.  The router uses the IGMP protocol to support ecient multicasting  transmission  of  identical  content, such  as  multimedia,  from  a  source  to  a  number of recipients. This option must  be enabled  if any applications on the LAN participate in a multicast group. If you have a multimedia LAN application that  is  not  receiving  content  as  expected,  try enabling this option.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationTools CategoryIn this category the  user will be able to congure features  that are related to the  router itself.  Features like the time settings, login accounts, rmware update and more.
Section 3 - Software CongurationAdminIn the Admin Password section, the user can change the Administrator login password used for this device.The following parameters will be available for conguration:Password: Enter the new login password used here.Verify Password: Re-enter the new login password here.In  the  User  Password  section,  the  user  can  change  the  User  login password used for this device.The following parameters will be available for conguration:Password: Enter the new login password used here.Verify Password: Re-enter the new login password here.In the System Name section, the user can change the gateway name used for this device.The following parameters will be available for conguration:Gateway Name: Enter the router gateway name used here.The following parameters will be available for conguration:Enable Graphical Authentication:Tick  this  option  to  enable  the  graphical  image conrmation  when  the  user  login  to  the  web conguration. This page will allow you to change the Administrator password and congure the authentication settings. This window also allows you to enable Remote Management, via the Internet. For security reasons, it is recommended that you change the password for the Admin and User accounts. Be sure to write down the new password to avoid having to reset the router in case they are forgotten.
Section 3 - Software CongurationEnable Remote Management:Tick  this  option  to  enable  remote  management. This option will enable the router to be accessible from the Internet port.Remote Admin Port:Enter the remote administration port number used here. Sometimes services like an internal web server will occupy the port number 80. In this option the user can change the remote administration port to 8080 for example.Remote Admin Inbound Filter:Select the appropriate remote admin inbound lter behavior here. Options to choose from are Allow All and Deny All.Details: Enter the remote admin inbound lter detail description used here.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationTimeThe Time window allows you to congure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be congured to automatically adjust the time when needed.The following parameters will be available for conguration:Time: Here  will  be  displayed  the  current  time conguration running on this device.Time Zone: Select  the  appropriate  time  zone  used  on  this device here.Enable Daylight Saving:Check this box if the country  your are located in uses Daylight Saving time. Daylight Saving Oset:Select the daylight savings oset used here.Daylight Saving Dates:Select  the  start  date  and  end  date  for  daylight saving time.Time and Date CongurationHere the user can congure the time zone as well as the daylight savings settings used for this router.Automatic Time and Date CongurationHere the user can congure whether this router will automatically synchronize it’s time and date with a public time server.The following parameters will be available for conguration:Automatically synchronize:NTP  is  short  for  Network  Time  Protocol.  NTP synchronizes computer  clock  times  in  a  network of computers. Tick this option to enable automatic time and date synchronizing.NTP Server Used: Select the appropriate time server used here. The interval at which the router will communicate with the NTP server is set to 7 days.Update Now: After selecting the appropriate time server and enabling the automatic synchronization option, click on this button to update the current time and date of the router.
Section 3 - Software CongurationSet the Time and Date ManuallyHere the user can congure the time and date values, used by this router, manually. Here the user can also synchronize the router’s time with the conguration computer’s time.The following parameters will be available for conguration:Set Manually: Here the user can manually congure the date and time used by this device. Options to congure are Year, Month, Day, Hour, Minute, and Second.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.SyslogThe Syslog options allow you to send log information to a System Log Server.The following parameters will be available for conguration:Enable Logging To SysLog Server:Tick this option to enable the Syslog feature.Syslog Server IP Address:Enter the Syslog Server IP address used here.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationEmail SettingsEmail NoticationWhen this option is enabled, router activity logs or rmware upgrade notications can be emailed to a designated email address.The following parameters will be available for conguration:Enable Email Notication:Tick  this  option  to  enable  the  Email  notication feature.Email SettingsHere this user can manually enter the email settings required to enable the email notication feature.The following parameters will be available for conguration:From Email Address:This  email  address  will  appear  as  the  sender when you  receive a log le or  rmware  upgrade notication via email.To Email Address:Enter the email address where you want the email sent.Email Subject: Enter  the  text  that  you  want  to  appear  in  the subject line of the e-mail that is sent.SMTP Server Address:Enter the SMTP server address for sending email. If your SMTP server requires authentication, select this option.SMTP Server Port:Enter the SMTP server port number used for sending email. Enable Authentication:Tick this option if the SMTP server requires authentication for sending mail.The Email feature can be used to send the system log les and router alert messages to your email address.
Section 3 - Software CongurationEmail Log When Full or on ScheduleNormally emails are sent at the starting and ending time dened in the schedule.  However,  rebooting  the  router  during  the  schedule  period will cause additional emails to be sent.The following parameters will be available for conguration:On Log Full: Select  this option  if you want logs to be sent by email when the log is full.On Schedule: Select this option if you want logs to be sent by email according to a schedule.Schedule: If you selected the ‘On Schedule’ option, select one of the dened schedule rules. If you do not see the schedule you need in the list of schedules, go to the Tools > Schedules screen and create a new schedule.Detail: Enter a detailed description here.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.Account Name: Enter your account for sending email.Password: Enter the password associated with the account.Verify Password: Re-enter the password associated with the account here.Send Mail Now: Click this button to send a test email from the Router to verify that the email settings have been congured correctly.
Section 3 - Software CongurationSystemThis section allows you to manage the router’s conguration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.The following parameters will be available for conguration:Save Settings To Local Hard Drive:Use  this  option  to  save  the  current  router conguration settings to a le on the hard disk of the computer you  are  using. First, click  the  Save button. A le dialog  will appear,  allowing you to select a location and le name for the settings.Load Settings From Local Hard Drive:Use  this  option  to  load  previously  saved  router conguration settings. First, use the Browse option to  nd  a  previously  saved  le  of  conguration settings.  Then,  click  the  Restore  Conguration From File button below to transfer those settings to the router.Restore To Factory Default Settings:This option  will  restore all  conguration settings back  to  the  settings  that  were  in  eect  at  the time  the  router  was  shipped  from  the  factory. Any  settings  that  have  not  been  saved  will  be lost, including any rules that you have created. If you want to save the current router conguration settings, use the Save button above.Reboot The Device:Click to reboot the router.Clear Language Pack:If you previously installed a  language pack  and want to revert all the  menus on  the Router interface back to the default language settings, click the Clear button.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationFirmwareUse the Firmware window to upgrade the rmware of the Router and install language packs. If you plan to install new rmware, make sure the rmware you want to use is on the local hard drive of the computer. If you want to install  a  new language  pack, make  sure that you have the language pack available. Please check the support site for rmware updates. You can download rmware upgrades to your hard drive from the support site.In  the  Firmware  Information  section  the  user  can  view  the  Current Firmware Version number running on this device, the Current Firmware Date of this same rmware version running on this device, and a button to click that will Check Online Now for Latest Firmware Version.In the Firmware Upgrade section the user can physically upgrade the rmware of this device clicking on the Browse button and navigating to the rmware le, saved on the local hard drive. After locating the le, click on the Upload button to initiate the rmware upgrade.Note:  Some  rmware  upgrades  will  reset  the  conguration,  of  the device, to factory defaults. Be sure to save the current conguration rst before any rmware update.In the Language Pack Upgrade section, the user can change the router’s language pack by clicking on the Browse button and navigating to the language pack, downloaded to the computer. After navigating to the language pack le, click on the Upload button to initiate the language pack  upload  and  conguration.  Always  keep  a  close  lookout  on  the local vendor’s website for new rmware upgrades and language packs.Note: Always update the rmware or language packs for this device using the wired connection. Never upgrade using a wireless connection.
Section 3 - Software CongurationDynamic DNSThe  DDNS  feature  allows  you  to  host  a  server  (Web,  FTP,  Game  Server,  etc…)  using  a  domain  name  that  you  have  purchased  (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.The following parameters will be available for conguration:Enable Dynamic DNS:Dynamic  Domain  Name  System  is  a  method  of keeping a  domain  name  linked  to  a changing IP Address. Check the box to enable DDNS.Server Address: Choose your DDNS provider from the drop down menu.Host Name: Enter the Host Name that you registered with your DDNS service provider.Username or Key:Enter the Username or Key for your DDNS account.Password or Key: Enter the Password or Key for your DDNS account.Verify Password or Key:Re-enter  the  Password  or  Key  for  your  DDNS account.Timeout: Enter the timeout value used for the DDNS account here.Status: Displays the DDNS connection status here.
Section 3 - Software CongurationThe following parameters will be available for conguration:Enable: Tick this option to enable the Dynamic DNS feature for IPv6 hosts.IPv6 Address: Enter  the  IPv6  Address  used  here.  Alternatively, the  user  can  select  the  Computer  Name  for  the drop-down list and click on the << button to add it the IPv6 Address eld.Host Name: Enter  the  IPv6  host  name  used  for  the  DDNS account here.Click on the Save button to add the IPv6 host to the IPv6 Dynamic DNS List.Click on the Clear button to clear the information entered in the elds.
Section 3 - Software CongurationIn  the  IPv6  Dynamic  DNS  List  section,  a  list  of  IPv6  hosts  will  be displayed. Tick the Enable checkbox to make the host active. To edit a specic entry click on the   icon. To remove a specic entry, click on the   icon.Click on the Save Settings button to accept the changes made.Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software CongurationSystem CheckThis useful diagnostic utility can be used to check if a computer is on the Internet. It sends ping packets and listens for replies from the specic host.In the Ping Test section the user can test the Internet connectivity by entering in a host name or the IP address that you want to Ping and click on the Ping button. The status of your Ping attempt will be displayed in the Ping Result box.In the IPv6 Ping Test section the user can test the Internet connectivity by entering in a host name or the IPv6 address that you want to Ping and click on the Ping button. The status of your Ping attempt will be displayed in the Ping Result box.In  the  Ping  Result  section  the  results  of  the  attempted  ping  will  be displayed.
Section 3 - Software CongurationSchedulesThe following parameters will be available for conguration:Name: Enter the custom name for the new schedule rule here. This name is used for identication.Day(s): To use  every day in  the week for this rule, select the All Week option. To use only selected days for this rule, select the Select Day(s) option and tick the appropriate days used for this rule.All Day - 24 hrs: To enable this rule to run 24 hours instead of only a certain part of the day, tick this option.Time Format: Select the appropriate time format to use here.Start Time: If the All Day option is not selected, the user can enter the starting time here.End Time: If the All Day option is not selected, the user can enter the ending time here.Click on the Add button to add this new rule to the schedule rules list.Click on the Cancel button to discard the information and cancel the rule addition.In the Schedule Rules List section, the user can view the available schedule rules created. To edit an existing rule, click on the   icon of the specic entry, To remove an existing rule, click on the   icon of the specic entry.Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.
Section 3 - Software CongurationStatus CategoryIn this category the user will be able to view information regarding the conguration and functionality of this device. The information includes WAN, LAN and Wireless congurations, System, Firewall, Router logs, and more.
Section 3 - Software CongurationDevice InfoThis page displays the current information for the router. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP.In  the  General  section,  information  about  the  time  and  rmware  is being displayed.In the WAN section, information about the Internet connection is being displayed.In  the  LAN  section,  information  about  the  Local  Area  Network conguration is being displayed.
Section 3 - Software CongurationIn the Wireless LAN section, information about the Wireless Local Area Network conguration is being displayed.In the LAN Computers section, a list of actively connected nodes are being displayed.In the IGMP Multicast Memberships section, a list of Multicast Group Addresses are being displayed.
Section 3 - Software CongurationLogsThe router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can dene what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log les to a computer on your network that is running a Syslog utility.The following parameters will be available for conguration:Log Type: Use  the  radio  buttons  to  select  the  types  of messages that you want to display from the  log. System,  Firewall  &  Security,  and  Router  Status messages can be selected.Log Level: There  are  three  levels  of  message  importance: Critical,  Warning,  and  Information.  Select  the levels that you want displayed in the log.The following parameters will be available for conguration:First - Last Page: Use  these  buttons  to navigate to the rst  or  last page of the router logs.Previous - Next: Use  these  buttons  to  navigate  to  the  next  or previous page of the router logs.Clear: Click on this button to clear all the contents from the log.Link to Email Log Settings:Click this button to open the Email Settings screen so that you can change the Email conguration for sending logs.In the Save Log File section, the user can click on the Save button save the Router’s log entries to a log le on your computer.
Section 3 - Software CongurationStatisticsIn the LAN Statistics section, the user can view the trac statistics that occurred on the LAN interface. Information that is displayed includes the packets sent and  received,  packets  dropped, collisions  that  occurred, and error packets sent and received.In the WAN Statistics section, the user can view the trac statistics that occurred on the WAN interface. Information that is displayed includes the packets sent and received, packets dropped, collisions that occurred, and error packets sent and received.In the Wireless Statistics section, the user can view the trac statistics that occurred on  the Wireless interface. Information  that  is  displayed includes the packets sent and received, packets dropped, collisions that occurred, and error packets sent and received.Click on the Refresh Statistics button to refresh the display page.Click on the Reset Statistics button to clear all the statistic information for all the elds displayed.The screen below displays the Trac Statistics. Here you can view the amount of packets that pass through the router on both the WAN, LAN ports and the 802.11n/g (2.4GHz) wireless band. The trac counter will reset if the device is rebooted.
Section 3 - Software CongurationInternet SessionsThe Internet Sessions page displays full details of active Internet sessions through  your  router.  An  Internet  session  is  a  conversation  between a  program or  application  on  a  LAN-side  computer and  a  program  or application on a WAN-side computer.In the section all the active Internet sessions will be displayed.WirelessThe  wireless  client  table  displays  a  list  of  current connected  wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.In the Number of Wireless Clients - 2.4GHz Band section a list of 2.4GHz active wireless clients will be displayed.
Section 3 - Software CongurationIPv6The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.In the IPv6 Connection Information section, more information about the IPv6 connection will be displayed. Information like the connection type, gateway address, Link-Local address, DNS Servers, and more.In  the  LAN  IPv6 Computers section,  a  list  of actively  connected  LAN IPv6 computers will be displayed.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.    This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.   However, there is no guarantee that interference will not occur in a particular installation.    If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  -  Reorient or relocate the receiving antenna. -  Increase the separation between the equipment and receiver. -  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -  Consult the dealer or an experienced radio/TV technician for help.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.  IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.    Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoqu
 Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.     以下警語適用台灣地區  經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Navigation menu