D Link IR655C1 Xtreme N Gigabit Router User Manual

D Link Corporation Xtreme N Gigabit Router

user manual

Version 3.0 | 05/09/2013DIR-655User ManualWireless N Gigabit Router
iD-Link DIR-655 User ManualD-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes.Manual RevisionsTrademarksD-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.Copyright © 2008-2013 by D-Link Corporation.All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.Revision Date Description2.0 May 25, 2010 • New Revision2.1 July 6, 2012• Added IPv6 Routing and Firewall• Added QRS Mobile app• Added Quick Setup Wizard3.0 May 9, 2013 • Removed WISH• Removed QRS Mobile appPreface
iiD-Link DIR-655 User ManualTable of ContentsPreface ................................................................................................. iManual Revisions ...............................................................................................iTrademarks ..........................................................................................................iProduct Overview ..............................................................................1Package Contents ........................................................................................... 1System Requirements .................................................................................... 2Introduction ...................................................................................................... 3Features ..................................................................................................... 4Hardware Overview ........................................................................................ 5Connections ............................................................................................. 5LEDs ............................................................................................................6Installation ......................................................................................... 7Before you Begin ............................................................................................. 7Wireless Installation Considerations ........................................................8Getting Started ..................................................................................9Quick Setup Wizard ......................................................................................10Conguration ...................................................................................16Internet Connection Setup ........................................................................17Manual Conguration ........................................................................18Static IP ...............................................................................................18Dynamic IP (DHCP) ........................................................................19PPPoE (DSL) ......................................................................................20PPTP ....................................................................................................22L2TP .....................................................................................................24DS-Lite ................................................................................................26Wireless Settings ...........................................................................................27Manual Wireless Connection Setup...............................................28Wireless Security ..................................................................................29What is WPA? ....................................................................................29Wireless Security Setup Wizard .................................................30WPA-Personal (PSK) .......................................................................32WPA-Enterprise (RADIUS) ............................................................33Network Settings ...........................................................................................35Router Settings .....................................................................................35DHCP Server Settings .........................................................................36DHCP Reservation ................................................................................37Media Server ...................................................................................................38IPv6 .....................................................................................................................39IPv6 Internet Connection Setup Wizard .......................................40IPv6 over PPPoE ..............................................................................42Static IPv6 Address Connection ................................................43Tunneling Connection (6rd) .......................................................44IPv6 Manual Setup ...............................................................................45Auto Detection ................................................................................45Static IPv6 ..........................................................................................46Autoconguration..........................................................................47PPPoE ..................................................................................................48IPv6 in IPv4 Tunneling...................................................................506to4 Tunneling ................................................................................516rd ........................................................................................................52Local Connectivity Only ...............................................................53Advanced Settings ........................................................................................54Virtual Server .........................................................................................54Port Forwarding ....................................................................................55Table of Contents
iiiD-Link DIR-655 User ManualTable of ContentsApplication Rules .................................................................................56QoS Engine .............................................................................................57Network Filter ........................................................................................59Access Control .......................................................................................60Access Control Wizard...................................................................60Website Filter .........................................................................................63Inbound Filter ........................................................................................64Firewall Settings ...................................................................................65Routing ....................................................................................................67Advanced Wireless ...............................................................................68Wi-Fi Protected Setup (WPS) ............................................................69Advanced Network Settings ............................................................71Guest Zone .............................................................................................72IPv6 Firewall ...........................................................................................73IPv6 Routing ...........................................................................................74Tools ...................................................................................................................75Admin .......................................................................................................75Time ..........................................................................................................76SysLog ......................................................................................................77E-mail Settings ......................................................................................78System ......................................................................................................79Firmware..................................................................................................80Dynamic DNS .........................................................................................81System Check ........................................................................................82Schedules ................................................................................................83Status .................................................................................................................84Device Info ..............................................................................................84Logs ...........................................................................................................85Statistics ...................................................................................................86Internet Sessions ..................................................................................87Routing ....................................................................................................88Wireless ....................................................................................................89IPv6 ............................................................................................................90IPv6 Routing ...........................................................................................91Support .............................................................................................................92Connect a Wireless Client to your Router ......................................93WPS Button ......................................................................................................93Windows® 8 .....................................................................................................94WPA/WPA2 ..............................................................................................94Windows® 7 .....................................................................................................96WPA/WPA2 ..............................................................................................96WPS ...........................................................................................................99Windows Vista® ........................................................................................... 103WPA/WPA2 ........................................................................................... 104WPS/WCN 2.0...................................................................................... 106Windows® XP ............................................................................................... 107WPA/WPA2 ........................................................................................... 108Troubleshooting ............................................................................110Wireless Basics ...............................................................................114Tips .................................................................................................................. 116Wireless Modes ........................................................................................... 117Networking Basics .........................................................................118Check your IP address ............................................................................... 118Technical Specications ................................................................120
1D-Link DIR-655 User ManualSection 1 - Product OverviewProduct OverviewPackage ContentsNote: Using a power supply with a dierent voltage rating than the one included with the DIR-655 will cause damage and void the warranty.D-Link DIR-655 Wireless N Gigabit Router with 3 Detachable AntennasPower AdapterCAT 5 Ethernet CableCD-ROM
2D-Link DIR-655 User ManualSection 1 - Product OverviewSystem RequirementsNetwork Requirements• An Ethernet-based Cable or DSL modem• IEEE 802.11n or 802.11g wireless clients• 10/100/1000 EthernetWeb-based Conguration Utility RequirementsComputer with the following:• Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapterBrowser Requirements:• Internet Explorer 6.0 or higher• Mozilla 1.7.12 or higher• Firefox 1.5 or higher• Safari 1.0 or higher (with Java 1.3.1 or higher) Windows® Users: Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version.CD Installation Wizard RequirementsComputer with the following:• Windows 7, Vista®, or XP with Service Pack 2• An installed Ethernet adapter• CD-ROM drive
3D-Link DIR-655 User ManualSection 1 - Product OverviewIntroductionTOTAL PERFORMANCECombines award winning router features and 802.11n wireless technology to provide the best wireless performance.TOTAL SECURITYThe most complete set of security features including Active Firewall and WPA2™ to protect your network against outside intruders.TOTAL COVERAGEProvides greater wireless signal rates even at farther distances for excellent coverage throughout the whole home.ULTIMATE PERFORMANCEThe D-Link Wireless N Gigabit Router (DIR-655) is a 802.11n compliant device that delivers real world performance of up to 650% faster than an 802.11g wireless connection (also faster than a 100Mbps wired Ethernet connection). Create a secure wireless network to share photos, les, music, video, printers, and network storage throughout your home. Connect the Wireless N Gigabit Router to a cable or DSL modem and share your high-speed Internet access with everyone on the network. In addition, this router includes a Quality of Service (QoS) engine that keeps digital phone calls (VoIP) and online gaming smooth and responsive, providing a better Internet experience.EXTENDED WHOLE HOME COVERAGEPowered by Wireless N technology, this high performance router provides superior home coverage while reducing dead spots. The Wireless N Gigabit Router is designed for use in bigger homes and for users who demand higher performance networking. Add a Wireless N notebook or desktop adapter and stay connected to your network from virtually anywhere in your home.TOTAL NETWORK SECURITYThe Wireless N Gigabit Router supports all of the latest wireless security features to prevent unauthorized access, be it from over the wireless network or from the Internet. Support for WPA standards ensure that you’ll be able to use the best possible encryption method, regardless of your client devices. In addition, this Wireless N Gigabit Router utilizes dual active rewalls (SPI and NAT) to prevent potential attacks from across the Internet.* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal range.
4D-Link DIR-655 User ManualSection 1 - Product Overview• Faster Wireless Networking - The DIR-655 provides up to 300 Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds 650% faster than 802.11g.• Compatible with 802.11g Devices - The DIR-655 is still fully compatible with the IEEE 802.11g standard, so it can connect with existing 802.11g PCI, USB and CardBus adapters.• Advanced Firewall Features - The web-based user interface displays a number of advanced network management features including: • Content Filtering - Easily applied content ltering based on MAC address, URL, and/or domain name.• Filter Scheduling - These lters can be scheduled to be active on certain days or for a duration of hours or minutes.• Secure Multiple/Concurrent Sessions - The DIR-655 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-655 can securely access corporate networks.• User-friendly Setup Wizard - Through its easy-to-use web-based user interface, the DIR-655 lets you control what information is accessible to those on the wireless network, whether from the Internet or from your company’s server. Congure your router to your specic settings within minutes.* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal range.Features
5D-Link DIR-655 User ManualSection 1 - Product OverviewHardware OverviewConnections1LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and hubs.2Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem.3USB Connect a USB ash drive or printer.4On/O Button Pressing the on/o button toggles power to the router.5Reset Pressing the Reset button restores the router to its original factory default settings.6Power Receptor Receptor for the supplied power adapter.12 3654
6D-Link DIR-655 User ManualSection 1 - Product OverviewLEDs123451Power LED A solid light indicates a proper connection to the power supply.2Internet LED A solid light indicates connection on the Internet port. This LED blinks during data transmission. A solid blue light indicates that there is an Internet connection, an orange light indicates that there is none.3WLAN LED A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission.4Local Network’s LED A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission. 5USB LED A solid light indicates a USB drive or a printer is plugged in.
7D-Link DIR-655 User ManualSection 2 - InstallationBefore you BeginInstallationThis section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Please congure the router with the computer that was last connected directly to your modem. Also, you can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn o your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet). If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoET, BroadJump, or EnterNet 300 from your computer or you will not be able to connect to the Internet.
8D-Link DIR-655 User ManualSection 2 - InstallationWireless Installation ConsiderationsThe D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2 degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.3. Building materials make a dierence. A solid metal door or aluminum studs may have a negative eect on range. Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.5. If you are using 2.4 GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4 GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use.
9D-Link DIR-655 User ManualSection 3 - CongurationThe DIR-655 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the wizard to guide you quickly through the installation process. Insert the Wizard CD in the CD-ROM drive.If the CD autorun function does not automatically start on your computer, go to Start > Run. In the run box type “D:\WIZARD.exe” (where D: represents the drive letter of your CD-ROM drive).When the autorun screen appears, click Start.Getting StartedNote: It is recommended to write down the SSID and security key, followed by the login password on the provided CD holder.
10D-Link DIR-655 User ManualSection 3 - CongurationIf you did not run the setup wizard from the CD and this is the rst time logging into the router, this wizard will start automatically. This wizard is designed to guide you through a step-by-step process to congure your new D-Link router and connect to the Internet.Click Next to continue. Quick Setup WizardIf this is your rst time installing the router, open your web browser. You will automatically be directed to the Wizard Setup Screen. If you have already congured your settings and you would like to access the conguration utility, please refer to page 16.
11D-Link DIR-655 User ManualSection 3 - CongurationPlease wait while your router detects your internet connection type. If the router detects your Internet connection, you may need to enter your ISP information such as username and password.If the router does not detect a valid Ethernet connection from the Internet port, this screen will appear. Connect your broadband modem to the Internet port and then click Try Again.If the router detects an Ethernet connection but does not detect the type of Internet connection you have, this screen will appear. Click Guide me through the Internet Connection Settings to display a list of connection types to choose from.
12D-Link DIR-655 User ManualSection 3 - CongurationSelect your Internet connection type and click Next to continue.If the router detected or you selected PPPoE, enter your PPPoE username and password and click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.If the router detected or you selected PPTP, enter your PPTP username, password, and other information supplied by your ISP. Click Next to continue.
13D-Link DIR-655 User ManualSection 3 - CongurationIf the router detected or you selected L2TP, enter your L2TP username, password, and other information supplied by your ISP. Click Next to continue. If the router detected or you selected Static, enter the IP and DNS settings supplied by your ISP. Click Next to continue.
14D-Link DIR-655 User ManualSection 3 - CongurationFor both the 2.4 GHz and 5 GHz segments, create a wireless network a name (SSID) using up to 32 characters.Create a wireless security passphrase or key (between 8-63 characters). Your wireless clients will need to have this passphrase or key entered to be able to connect to your wireless network.Click Next to continue.In order to secure your router, please enter a new password. Check the Enable Graphical Authentication box to enable CAPTCHA authentication for added security. Click Next to continue.Select your time zone from the drop-down menu and click Next to continue.
15D-Link DIR-655 User ManualSection 3 - CongurationThe Setup Complete window will display your wireless settings. Click Save and Connect to continue.If you want to create a bookmark to the router, click OK. Click Cancel if you do not want to create a bookmark.If you clicked Yes, a window may appear (depending on what web browser you are using) to create a bookmark.The router will now reboot. Please allow a minute or two. Click the Continue button once it is active.
16D-Link DIR-655 User ManualSection 3 - CongurationTo access the conguration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).You can also enter http://dlinkrouter to connect.Select Admin from the drop-down menu and then enter your password. The password is left blank by default.If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance.Conguration
17D-Link DIR-655 User ManualSection 3 - CongurationInternet Connection SetupYou may click Internet Connection Setup Wizard to quickly congure your router. Refer to page 10 for details.If you want to enter your settings without running the wizard, click Manual Internet Conguration Setup and skip to the next page.
18D-Link DIR-655 User ManualSection 3 - CongurationAdvanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.Check to enable true Gigabit routing. This will increase the throughput of the WAN-LAN connectivity of the router.Enter the IP address assigned by your ISP.Enter the subnet mask assigned by your ISP.Enter the gateway assigned by your ISP.The DNS server information will be supplied by your ISP (Internet Service Provider.)Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1500 is the default MTU.The default MAC address is set to the Internet port’s physical interface MAC address on the broadband router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.Enable Advanced DNS Service:True Gigabit Routing Connectivity Setting:IP Address:Subnet Mask:Default Gateway:DNS Servers:MTU:MAC Address:Manual CongurationStatic IPSelect Static IP if your IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the elds must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.
19D-Link DIR-655 User ManualSection 3 - CongurationDynamic IP (DHCP)Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.Check to enable true Gigabit routing. This will increase the throughput of the WAN-LAN connectivity of the router.The host name is optional but may be required by some ISPs. Leave blank if you are not sure.Check the box if you are having problems obtaining an IP address from your ISP.Enter the primary and secondary DNS server IP addresses assigned by your ISP. These addresses are usually obtained automatically from your ISP. Leave at 0.0.0.0 if you did not specically receive these from your ISP.Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1500 is the default MTU.The default MAC address is set to the Internet port’s physical interface MAC address on the broadband router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.Enable Advanced DNS Service:Host Name:MAC Address:Primary/Secondary DNS Server:MTU:Use Unicasting:True Gigabit Routing Connectivity Setting:Select Dynamic IP (DHCP) to obtain IP address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such as Comcast and Cox.
20D-Link DIR-655 User ManualSection 3 - CongurationAdvanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.Check to enable true Gigabit routing. This will increase the throughput of the WAN-LAN connectivity of the router. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Enable Advanced DNS Service:True Gigabit Routing Connectivity Setting:Address Mode:IP Address:User Name:Password:Service Name:Reconnection Mode:Maximum Idle Time:PPPoE (DSL)Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
21D-Link DIR-655 User ManualSection 3 - CongurationEnter the primary and secondary DNS server addresses (Static PPPoE only).Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default MTU.The default MAC address is set to the Internet port’s physical interface MAC address on the broadband router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.DNS Addresses:MTU:MAC Address:
22D-Link DIR-655 User ManualSection 3 - CongurationAdvanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPTP only).Enter the primary and secondary DNS server addresses (Static PPTP only).Enter the gateway IP address provided by your ISP.Enter the server IP provided by your ISP (optional).Enter your PPTP username.Enter your PPTP password and then retype the password in the next box.Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.The DNS server information will be supplied by your ISP (Internet Service Provider.)Enable Advanced DNS Service:Address Mode:PPTPChoose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. PPTP IP Address:PPTP Subnet Mask:PPTP Gateway:PPTP Server IP:Username:Password: Reconnect Mode:Maximum Idle Time:DNS Addresses:
23D-Link DIR-655 User ManualSection 3 - CongurationMaximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1400 is the default MTU.The default MAC address is set to the Internet port’s physical interface MAC address on the broadband router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.MTU:MAC Address:
24D-Link DIR-655 User ManualSection 3 - CongurationAdvanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the L2TP IP address supplied by your ISP (Static only).Enter the subnet mask supplied by your ISP (Static only).Enter the gateway IP address provided by your ISP.Enter the server IP provided by your ISP (optional).Enter your L2TP username.Enter your L2TP password and then retype the password in the next box.Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Enter the primary and secondary DNS server addresses (Static L2TP only).Enable Advanced DNS Service:Address Mode:L2TP IP Address:L2TP Subnet Mask:L2TP Gateway:L2TP Server IP:Username:Password:Reconnect Mode:Maximum Idle Time: DNS Servers:L2TPChoose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.
25D-Link DIR-655 User ManualSection 3 - CongurationMaximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1400 is the default MTU.The default MAC address is set to the Internet port’s physical interface MAC address on the broadband router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.MTU:Clone MAC Address:
26D-Link DIR-655 User ManualSection 3 - CongurationDS-LiteDS-Lite is an IPv6 connection type. After selecting DS-Lite, the following parameters will be available for conguration:DS-Lite Conguration:AFTR IPv6 Address:B4 IPv6 Address:WAN IPv6 Address:IPv6 WAN Default Gateway:Select DS-Lite DHCPv6 Option to let the router allocate the AFTR IPv6 address automatically. Select Manual Conguration to enter the AFTR IPv6 address in manually.After selecting the Manual Conguration option above, enter the AFTR IPv6 address used here.Enter the B4 IPv4 address value used here.Once connected, the WAN IPv6 address will be displayed here.Once connected, the IPv6 WAN default gateway address will be displayed here.
27D-Link DIR-655 User ManualSection 3 - CongurationWireless SettingsIf you want to congure the wireless settings on your router using the wizard, click Wireless Security Setup Wizard and refer to page 37.Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to page 93.If you want to manually congure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.
28D-Link DIR-655 User ManualSection 3 - CongurationCheck the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.The schedule of time when the wireless settings rules will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Service Set Identifier (SSID) is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive.The Auto Channel Scan setting can be selected to allow the DIR-655 to choose the channel with the least amount of interference.Indicates the channel setting for the DIR-655. By default the channel is set to 6. The channel can be changed to t the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out.Select one of the following:802.11g Only - Select if all of your wireless clients are 802.11g.802.11n Only - Select only if all of your wireless clients are 802.11n.Mixed 802.11n and 802.11g - Select if you are using a mix of 802.11n and 11g wireless clients.Select the channel width:Auto 20/40 - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.20MHz - Select if you are not using any 802.11n wireless clients.40MHz - Select if using only 802.11n wireless clients.Select the transmit rate. It is strongly suggested to select Best (Auto) for best performance.Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-655. If Invisible is selected, the SSID of the DIR-655 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-655Enable Wireless:Enable Auto Channel Scan:Manual Wireless Connection SetupWireless Network Name:Wireless Channel:802.11 Mode:Channel Width:Transmission Rate:Visibility Status:Schedule:
29D-Link DIR-655 User ManualSection 3 - CongurationWireless SecurityThis section will show you the dierent levels of security you can use to protect your data from intruders. The DIR-655 oers the following types of security:• WPA2™ (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key)• WPA™ (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)What is WPA?WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer’s hardware-specic MAC address, which is relatively simple to be snied out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network.WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point.WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network.
30D-Link DIR-655 User ManualSection 3 - CongurationWireless Security Setup WizardTo run the security wizard, click on Setup at the top and then click Launch Wireless Security Setup Wizard.Click Next to continue.
31D-Link DIR-655 User ManualSection 3 - CongurationThe following screen will show you your pre-shared key to enter on your wireless clients. Click Save to nish the security wizard.If you selected WPA-Enterprise, the RADIUS information will be displayed. Click Save to nish the security wizard.
32D-Link DIR-655 User ManualSection 3 - CongurationIt is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based conguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side.2. Next to Security Mode, select WPA-Personal.3. Next to WPA Mode, select Auto, WPA2 Only, or WPA Only. Use Auto if you have wireless clients using both WPA and WPA2.4. Next to Group Key Update Interval, enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default).5. Next to Pre-Shared Key, enter a key (passphrase). The key is entered as a pass-phrase in ASCII format at both ends of the wireless connection. The pass-phrase must be between 8-63 characters. 6. Click Save Settings to save your settings. If you are conguring the router with a wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router.WPA-Personal (PSK)
33D-Link DIR-655 User ManualSection 3 - CongurationIt is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.1. Log into the web-based conguration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Setup and then click Wireless Settings on the left side.2. Next to Security Mode, select WPA-Enterprise.3. Next to WPA Mode, select Auto, WPA2 Only, or WPA Only. Use Auto if you have wireless clients using both WPA and WPA2.4. Next to Group Key Update Interval, enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default).5. Next to Authentication Timeout, enter the amount of time before a client is required to re-authenticate (60 minutes is default). 6. Next to RADIUS Server IP Address enter the IP Address of your RADIUS server.7. Next to RADIUS Server Port, enter the port you are using with your RADIUS server. 1812 is the default port. 8. Next to RADIUS Server Shared Secret, enter the security key.WPA-Enterprise (RADIUS)
34D-Link DIR-655 User ManualSection 3 - Conguration9. If the MAC Address Authentication box is selected then the user will need to connect from the same computer whenever logging into the wireless network.10. Click Advanced to enter settings for a secondary RADIUS server.11. Click Save Settings to save your settings.
35D-Link DIR-655 User ManualSection 3 - CongurationThis section will allow you to change the local network settings of the router.Network SettingsRouter SettingsEnter the IP address of the router. The default IP address is 192.168.0.1.If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the conguration utility.Enter the subnet mask. The default subnet mask is 255.255.255.0.Enter the domain name (optional).Uncheck the box to transfer the DNS server information from your ISP to your computers. If checked, your computers will use the router for a DNS server.IP Address:Subnet Mask:Local Domain:Enable DNS Relay:
36D-Link DIR-655 User ManualSection 3 - CongurationDHCP Server SettingsDHCP stands for Dynamic Host Control Protocol. The DIR-655 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-655. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.Check this box to enable the DHCP server on your router. Uncheck to disable this function.Enter the starting and ending IP addresses for the DHCP server’s IP assignment.Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conict. The length of time for the IP address lease. Enter the lease time in minutes.Enable this feature to broadcast your networks DHCP server to LAN/WLAN clients.NetBIOS allows LAN hosts to discover all other computers within the network, enable this feature to allow the DHCP Server to oer NetBIOS conguration settings.Enable this feature to allow WINS information to be learned from the WAN side, disable to allow manual conguration.This feature allows the conguration of a NetBIOS domain name under which network hosts operate. This setting has no eect if the ‘Learn NetBIOS information from WAN’ is activated.Select the dierent type of NetBIOS node: Broadcast only, Point-to-Point, Mixed-mode, and Hybrid.Enter your primary (and secondary) WINS IP address(es).Enable DHCP Server:DHCP IP Address Range:DHCP Lease Time:Always Broadcast:NetBIOS Announcement:Learn NetBIOS from WAN:NetBIOS Scope:NetBIOS Mode Type:Primary/Secondary WINS IP Address:
37D-Link DIR-655 User ManualSection 3 - CongurationDHCP ReservationIf you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range.Check this box to enable the reservation.Enter the computer name or select from the drop-down menu and click <<.Enter the IP address you want to assign to the computer or device. This IP address must be within the DHCP IP address range.Enter the MAC address of the computer or device.If you want to assign an IP address to the computer you are currently on, click this button to populate the elds. Click Save to save your entry. You must click Save Settings at the top to activate your reservations. In this section you can see what LAN devices are currently leasing IP addresses.Click Revoke to cancel the lease for a specic LAN device and free an entry in the lease table. Do this only if the device no longer needs the leased IP address, because, for example, it has been removed from the network.Note: The Revoke option will not disconnect a PC with a current network session from the network; you would need to use MAC Address Filter to do that. Revoke will only free up a DHCP Address for the very next requester. If the previous owner is still available, those two devices may both receive an IP Address Conict error, or the second device may still not receive an IP Address; in that case, you may still need to extend the “DHCP IP Address Range” to address the issue, it is located in the DHCP Server section. The Reserve option converts this dynamic IP allocation into a DHCP Reservation and adds the corresponding entry to the DHCP Reservations List.Enable:Computer Name:IP Address:MAC Address:Copy Your PC’s MAC Address:Save:Number of Dynamic DHCP Clients:Revoke:Reserve:
38D-Link DIR-655 User ManualSection 3 - CongurationMedia ServerThis feature allows you to share music, pictures and videos from a USB external drive/thumb drive and/or SD card with any device connected to your network.Enable Media Server:Media Server Name:Check this box to enable the media server feature.Enter the media server’s name.
39D-Link DIR-655 User ManualSection 3 - CongurationIPv6On this page, the user can congure the IPv6 connection type. There are two ways to set up the IPv6 Internet connection. You can use the web-based IPv6 Internet Connection Setup Wizard or you can manually congure the connection.For the beginner user that has not congured a router before, click on the IPv6 Internet Connection Setup Wizard button and the router will guide you through a few simple steps to get your network up and running. Skip to the next page for details.For the advanced user that has congured a router before, click on the Manual IPv6 Internet Connection Setup button to input all the settings manually. Refer to page 45 for details.To congure the IPv6 local settings, click on the IPv6 Local Connectivity Setup button.
40D-Link DIR-655 User ManualSection 3 - CongurationIPv6 Internet Connection Setup WizardOn this page, the user can congure the IPv6 connection type using the IPv6 Internet Connection Setup Wizard.Click the IPv6 Internet Connection Setup Wizard button and the router will guide you through a few simple steps to get your network up and running. Click Next to continue to the next page. Click Cancel to discard the changes made and return to the main page.The router will try to detect whether its possible to obtain the IPv6 Internet connection type automatically. If this succeeds then the user will be guided through the input of the appropriate parameters for the connection type found.However, if the automatic detection fails, the user will be prompted to either Try again or to click on the Guide me through the IPv6 settings button to set up IPv6 manually, with the wizard’s guidance.
41D-Link DIR-655 User ManualSection 3 - CongurationThere are several connection types to choose from. If you are unsure of your connection method, please contact your IPv6 Internet service provider. Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled. The three options available on this page are IPv6 over PPPoE, Static IPv6 address and Route and Tunneling Connection. Choose the required IPv6 Internet Connection type and click on the Next button to continue. Click on the Prev button to return to the previous page. Click on the Cancel button to discard all the changes made and return to the main page.
42D-Link DIR-655 User ManualSection 3 - CongurationAfter selecting the IPv6 over PPPoE option, the user will be able to congure the IPv6 Internet connection, which requires a username and password to get online. Most DSL modems use this type of connection.The following parameters will be available for conguration:PPPoE Session: Select the PPPoE Session type. This option will state that this connection shares its information with the already congured IPv6 PPPoE connection, or the user can create a new PPPoE connection here.Username: Enter the PPPoE username. If you do not know your username, please contact your ISP.Password: Enter the PPPoE password. If you do not know your password, please contact your ISP.Verify Password: Re-enter the PPPoE password.Service Name: Enter the service name for this connection. (This is optional.)IPv6 over PPPoE
43D-Link DIR-655 User ManualSection 3 - CongurationChoose Static IPv6 Address Connection when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your IPv6 conguration settings. You must enter the IPv6 address, Subnet Prex Length, Default Gateway, Primary DNS Server and Secondary DNS Server. Your ISP provides you with all of this information.Use Link-Local Address:IPv6 Address:Subnet Prex Length:Default Gateway:Primary DNS Address:Secondary DNS Address:LAN IPv6 Address:The Link-local address is used by nodes and routers when communicating with neighboring nodes on the same link. This mode enables IPv6-capable devices to communicate with each other on the LAN side.Enter the WAN IPv6 address for the router here.Enter the WAN subnet prex length value used here.Enter the WAN default gateway IPv6 address used here.Enter the WAN primary DNS Server address used here.Enter the WAN secondary DNS Server address used here.These are the settings of the LAN (Local Area Network) IPv6 interface for the router. The router’s LAN IPv6 Address conguration is based on the IPv6 address and subnet assigned by your ISP. (A subnet with prex /64 is supported in LAN.)Static IPv6 Address Connection
44D-Link DIR-655 User ManualSection 3 - CongurationThe following parameters will be available for conguration:6rd IPv6 Prex: Enter the 6rd IPv6 address and prex value used here.IPv4 Address: Enter the IPv4 address used here.Mask Length: Enter the IPv4 mask length used here.Assigned IPv6 Prex: Displays the IPv6 assigned prex value here.6rd Border Relay IPv4 Address:Enter the 6rd border relay IPv4 address used here.IPv6 DNS Server: Enter the primary DNS Server address used here.When the setup wizard is complete, click on the Connect button to continue. Click on the Prev button to return to the previous page. Click on the Cancel button to discard all the changes made and return to the main page.After selecting the Tunneling Connection (6rd) option, the user can congure the IPv6 6rd connection settings.Tunneling Connection (6rd)
45D-Link DIR-655 User ManualSection 3 - CongurationIPv6 Manual SetupThere are several connection types to choose from: Auto Detection, Static IPv6, Autoconguration (SLAAC/DHCPv6), PPPoE, IPv6 in IPv4 Tunnel, 6to4, 6rd and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet service provider. If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled.Auto DetectionSelect Auto Detection to have the router detect and automatically congure your IPv6 setting from your ISP.
46D-Link DIR-655 User ManualSection 3 - CongurationStatic IPv6Select Static IPv6 from the drop-down menu.Enter the address settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the router’s LAN link-local address.Check to enable the autoconguration feature.Select Stateful (DHCPv6), SLAAC + RDNSS, or SLAAC + Stateless DHCPv6. Enter the start IPv6 address for the DHCPv6 range for your local computers.Enter the end IPv6 address for the DHCPv6 range for your local computers.Enter the IPv6 address lifetime (in minutes).My IPv6 Connection:WAN IPv6 Address Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Automatic IPv6 Address Assignment:Autoconguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
47D-Link DIR-655 User ManualSection 3 - CongurationAutocongurationSelect Autoconguration (Stateless/DHCPv6) from the drop-down menu.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Check to enable the DHCP-PD feature.Enter the LAN (local) IPv6 address for the router. Displays the router’s LAN link-local address.Check to enable the autoconguration feature.Check to enable automatic DHCP-PD in LAN.Select Stateful (DHCPv6), SLAAC + RDNSS, or SLAAC + Stateless DHCPv6. Enter the start IPv6 address for the DHCPv6 range for your local computers.Enter the end IPv6 address for the DHCPv6 range for your local computers.Enter the IPv6 address lifetime (in minutes).My IPv6 Connection:IPv6 DNS Settings:Primary/Secondary DNS Address:Enable DHCP-PD:LAN IPv6 Address:LAN Link-Local Address:Enable Automatic IPv6 Address Assignment:Enable Automatic DHCP-PD in LAN:Autoconguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
48D-Link DIR-655 User ManualSection 3 - CongurationPPPoESelect PPPoE from the drop-down menu.Enter the PPPoE account settings supplied by your Internet provider (ISP). Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default MTU.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Check to enable the DHCP-PD feature.Enter the LAN (local) IPv6 address for the router. Displays the router’s LAN Link-Local Address.My IPv6 Connection:PPPoE:Address Mode:IP Address:User Name:Password:Service Name:Reconnection Mode:Maximum Idle Time: MTU:IPv6 DNS Settings:Primary/Secondary DNS Address:Enable DHCP-PD:LAN IPv6 Address:LAN Link-Local Address:
49D-Link DIR-655 User ManualSection 3 - CongurationEnable Automatic IPv6 Address Assignment:Enable Automatic DHCP-PD in LAN:Autoconguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:Check to enable the autoconguration feature.Check to enable automatic DHCP-PD in LAN.Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6.Enter the start IPv6 address for the DHCPv6 range for your local computers.Enter the end IPv6 address for the DHCPv6 range for your local computers.Enter the IPv6 address lifetime (in minutes).
50D-Link DIR-655 User ManualSection 3 - CongurationIPv6 in IPv4 TunnelingSelect IPv6 in IPv4 Tunnel from the drop-down menu.Enter the settings supplied by your Internet provider (ISP). Automatically obtain a DNS server address or enter a specic DNS address.Check to enable the DHCP-PD feature.Enter the LAN (local) IPv6 address for the router. Displays the router’s LAN link-local address.Check to enable automatic IPv6 address assignment.Check to enable automatic DHCP-PD in LAN.Select Stateful (DHCPv6), SLAAC + RDNSS, or SLAAC + Stateless DHCPv6. Enter the start IPv6 address for the DHCPv6 range for your local computers.Enter the end IPv6 address for the DHCPv6 range for your local computers.Enter the router advertisement lifetime (in minutes).My IPv6 Connection:IPv6 in IPv4 Tunnel Settings:IPv6 DNS Settings:Enable DHCP-PD:LAN IPv6 Address:LAN IPv6 Link-Local Address:Enable Automatic IPv6 Address Assignment:Enable Automatic DHCP-PD in LAN:Autoconguration Type:IPv6 Address Range Start:IPv6 Address Range End:Router Advertisement Lifetime:
51D-Link DIR-655 User ManualSection 3 - Conguration6to4 TunnelingSelect 6to4 from the drop-down menu.Enter the IPv6 settings supplied by your Internet provider (ISP). Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the router’s LAN link-local address.Check to enable the autoconguration feature.Select Stateful (DHCPv6), SLAAC + RDNSS, or SLAAC + Stateless DHCPv6. Enter the start IPv6 address for the DHCPv6 range for your local computers.Enter the end IPv6 address for the DHCPv6 range for your local computers.Enter the IPv6 address lifetime (in minutes).My IPv6 Connection:6to4 Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Automatic DHCP-PD in LAN:Autoconguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
52D-Link DIR-655 User ManualSection 3 - Conguration6rdSelect 6rd from the drop-down menu.Enter the address settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the router’s LAN link-local address.Check to enable the autoconguration feature.Select Stateful (DHCPv6), SLAAC+RDNSS, or SLAAC + Stateless DHCPv6. Enter the start IPv6 address for the DHCPv6 range for your local computers.Enter the end IPv6 address for the DHCPv6 range for your local computers.Enter the router advertisement lifetime (in minutes).My IPv6 Connection:6rd Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Automatic DHCP-PD in LAN:Autoconguration Type:IPv6 Address Range Start:IPv6 Address Range End:Router Advertisement Lifetime:
53D-Link DIR-655 User ManualSection 3 - CongurationSelect Local Connectivity Only from the drop-down menu.Displays the IPv6 address of the router.My IPv6 Connection:LAN IPv6 Address Settings:Local Connectivity Only
54D-Link DIR-655 User ManualSection 3 - CongurationThis will allow you to open a single port. If you would like to open a range of ports, refer to the next page.Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the elds.Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<. Enter the port that you want to open. The private and public ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network.Select TCP, UDP or Both from the drop-down menu.The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Select Allow All (most common) or a created Inbound lter. You may create your own inbound lters in the Advanced > Inbound Filter page.Name:IP Address:Private Port/Public Port:Protocol Type:Schedule:Inbound Filter:Virtual ServerAdvanced Settings
55D-Link DIR-655 User ManualSection 3 - CongurationThis will allow you to open a single port or a range of ports.Port ForwardingEnter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the elds.Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the Computer Name drop-down menu. Select your computer and click <<. Enter the TCP and/or UDP port or ports that you want to open. You can enter a single port or a range of ports. Separate ports with a comma.Example: 24,1009,3000-4000The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Select Allow All (most common) or a created Inbound lter. You may create your own inbound lters in the Advanced > Inbound Filter page.Name:IP Address:TCP/UDP:Schedule:Inbound Filter:
56D-Link DIR-655 User ManualSection 3 - CongurationEnter a name for the rule. You may select a pre-dened application from the drop-down menu and click <<.This is the port used to trigger the application. It can be either a single port or a range of ports.Select the protocol of the trigger port (TCP, UDP or Both).This is the port number on the Internet side that will be used to access the application. You may dene a single port or a range of ports. You can use a comma to add multiple ports or port ranges.Select the protocol of the rewall port (TCP, UDP, or Both).The schedule of time when the Application Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Name:Trigger:Trac Type:Firewall:Trac Type:Schedule:Application RulesSome applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have diculties working through NAT (Network Address Translation). Application Rules makes some of these applications work with the DIR-655. If you need to run applications that require multiple connections, specify the port normally associated with an application in the Trigger Port eld, select the protocol type as TCP or UDP, then enter the rewall (public) ports associated with the trigger port to open them for inbound trac.The DIR-655 provides some predened applications in the table on the bottom of the web page. Select the application you want to use and enable it.
57D-Link DIR-655 User ManualSection 3 - CongurationQoS EngineThis option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP.This option is enabled by default when the QoS Engine option is enabled. This option will allow your router to automatically determine the uplink speed of your Internet connection.This displays the detected uplink speed.The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISP’s often note speed as a download/upload pair. For example, 1.5Mbits/284Kbits. Using this example, you would enter 284. Alternatively you can test your uplink speed with a service such as speedtest.net.This option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP.This option is enabled by default so that your router will automatically determine which programs should have network priority. For best performance, use the Automatic Classicationoption to automatically set the priority for your applications.This option should be enabled when you have a slow Internet uplink. It helps to reduce the impact that large low priority network packets can have on more urgent ones.A QoS Engine rule identies a specic message ow and assigns a priority to that ow. For most applications, automatic classication will be adequate and specic QoS Engine rules will not be required.The QoS Engine supports overlaps between rules, where more than one rule can match for a specic message ow. If more than one rule is found to match, the rule with the highest priority will be used.Enable Trac Shaping:Automatic Uplink Speed:Measured Uplink Speed:Manual Uplink Speed:Enable QoS Engine:Automatic Classication:Dynamic Fragmentation:QoS Engine Rules:The QoS Engine helps improve your network gaming performance by prioritizing applications. By default, the QoS Engine settings are disabled and application priority is not classied automatically.
58D-Link DIR-655 User ManualSection 3 - CongurationName:Priority:Protocol:Local IP Range:Local Port Range:Remote IP Range:Remote Port Range:Create a name for the rule that is meaningful to you.The priority of the message ow is entered here -- 1 receives the highest priority (most urgent) and 255 receives the lowest priority (least urgent).The protocol used by the messages.The rule applies to a ow of messages whose LAN-side IP address falls within the range set here.The rule applies to a ow of messages whose LAN-side port number is within the range set here.The rule applies to a ow of messages whose WAN-side IP address falls within the range set here.The rule applies to a ow of messages whose WAN-side port number is within the range set here.
59D-Link DIR-655 User ManualSection 3 - CongurationNetwork FilterSelect Turn MAC Filtering O, Allow MAC addresses listed below, or Deny MAC addresses listed below from the drop-down menu. Enter the MAC address you would like to lter.To nd the MAC address on a computer, please refer to the Networking Basics section in this manual. Select a DHCP client from the drop-down menu and click << to copy that MAC address. Click to remove the MAC address.Congure MAC Filtering:MAC Address:DHCP Client:Clear:Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers, by their MAC addresses, from accessing the network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the router.
60D-Link DIR-655 User ManualSection 3 - CongurationAccess ControlFirst, click the Enable Access Control box. Next, click the Add Policy button to start the Access Control Wizard. Add Policy:The Access Control section allows you to control access in and out of your network. Use this feature as “Parental Controls” to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games.Click Next to continue with the wizard.Access Control Wizard
61D-Link DIR-655 User ManualSection 3 - CongurationEnter a name for the policy and then click Next to continue.Select a schedule (i.e., Always) from the drop-down menu and then click Next to continue.Enter the following information and then click Next to continue:• Address Type - Select IP address, MAC address, or Other Machines.• IP Address - Enter the IP address of the computer you want to apply the rule to.• Machine Address - Enter the PC MAC address (i.e., 00:00.00.00.00).Select the ltering method and then click Next to continue.Note: If you select the Apply Advanced Port Filters option you will be forwarded to the Add Port Filters Rules window. Otherwise, you will be advanced to the Congure Web Access Logging window (see next page).
62D-Link DIR-655 User ManualSection 3 - CongurationEnter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number.To enable web logging, click Enable.Click Save to save the access control rule.Your newly created policy will now show up under Policy Table.
63D-Link DIR-655 User ManualSection 3 - CongurationAdd Website Filtering Rule:Website URL/Domain:Website FilterSelect either DENY computers access to ONLY these sites or ALLOW computers access to ONLY these sites.Enter the keywords or URLs that you want to allow or block. Click Save Settings.Website Filters are used to allow you to set up a list of websites that can be viewed by multiple users through the network. To use this feature, select to Allow or Deny, enter the domain or website and click Save Settings. You must also select Apply Web Filter under the Access Control section (page 60).
64D-Link DIR-655 User ManualSection 3 - CongurationEnter a name for the inbound lter rule.Select Allow or Deny.Check to enable the rule.Enter the starting IP address. Enter 0.0.0.0 if you do not want to specify an IP range.Enter the ending IP address. Enter 255.255.255.255 if you do not want to specify and IP range.Click the Add button to apply your settings. You must click Save Settings at the top to save the settings.This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule.Name:Action:Enable:Remote IP Start:Remote IP End:Add:Inbound Filter Rules List:The Inbound Filter feature provides an advanced method of controlling data received from the Internet. With this feature, you can congure inbound data ltering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features.Inbound Filter
65D-Link DIR-655 User ManualSection 3 - CongurationSPI (Stateful Packet Inspection), also known as dynamic packet ltering, helps to prevent cyber attacks by tracking more state per session. It validates that the trac passing through the session conforms to the protocol.Enable this feature to protect your network from certain kinds of “spoong” attacks. If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer.Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort.Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer obtains its IP address automatically using DHCP, be sure to make a static reservation on the Setup > Network Settings page so that the IP address of the DMZ machine does not change.Allows multiple machines on the LAN to connect to their corporate network using PPTP protocol.Allows multiple VPN clients to connect to their corporate network using IPSec. Some VPN clients support traversal of IPSec throughNAT. This ALG may interfere with the operation of such VPN clients. If you are having trouble connecting with your corporate network, try turning this ALG o. Please check with the system administrator of your corporate network whether your VPN client supportsNAT traversal.Enable SPI:Anti-Spoof Check:Enable DMZ:DMZ IP Address:PPTP:IPSEC (VPN):Firewall SettingsA rewall protects your network from the outside world. The DIR-655 oers a rewall type functionality. The Stateful Packet Inpection (SPI) feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
66D-Link DIR-655 User ManualSection 3 - CongurationRTSP:SIP:Allows applications that use Real Time Streaming Protocol to receive streaming media from the Internet. QuickTime and Real Player are some of the common applications using this protocol.Allows devices and applications using VoIP (Voice over IP) to communicate across NAT. Some VoIP applications and devices have the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are having trouble making VoIP calls, try turning this ALG o.
67D-Link DIR-655 User ManualSection 3 - CongurationEnter a name for your route.Enter the IP address of packets that will take this route.Enter the netmask of the route. Please note that the octets must match your destination IP address.Enter your next hop gateway to be taken if this route is used.The route metric is a value from 1 to 16 that indicates the cost of using this route. A value 1 is the lowest cost and 15 is the highest cost. Select the interface that the IP packet must use to transit out of the router when this route is used. Name:Destination IP:Netmask:Gateway:Metric:Interface:RoutingThe Routing option is an advanced method of customizing specic routes of data through your network.
68D-Link DIR-655 User ManualSection 3 - CongurationAdvanced WirelessSet the transmit power of the antennas.This enables 802.11d operation. 802.11d is a wireless specication developed to allow implementation of wireless networks in countries that cannot use the 802.11 standard. This feature should only be enabled if you are in a country that requires it.WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.Enable this option to reduce interference from other wireless networks in your area. If the channel width is operating at 40MHz and there is another wireless network’s channel over-lapping and causing interference, the router will automatically change to 20MHz. Transmit Power:WLAN Partition:WMM Enable:Short GI:HT20/40 Coexistence:
69D-Link DIR-655 User ManualSection 3 - CongurationWi-Fi Protected Setup (WPS)Enable the Wi-Fi Protected Setup feature. Note: If this option is unchecked, the WPS button on the side of the router will be disabled.Disabling the wireless security settings prevents the settings from being changed by the Wi-Fi Protected Setup feature of the router. Devices can still be added to the network using Wi-Fi Protected Setup, however, the settings of the network will not change once this option is checked.A PIN is a unique number that can be used to add the router to an existing network or to create a new network. The default PIN may be printed on the bottom of the router. For extra security, a new PIN can be generated. You can restore the default PIN at any time. Only the Administrator (“admin” account) can change or reset the PIN.Shows the current PIN. Create a random number that is a valid PIN. This becomes the router’s PIN. You can then copy this PIN to the user interface of the registrar.This wizard helps you add wireless devices to the wireless network.Restore the default PIN of the router. Enable:Disable WPS-PIN Method:PIN Settings:Current PIN:Generate New PIN:Reset PIN to Default:Wi-Fi Protected Setup (WPS) System is a simplied method for securing your wireless network during initial setup as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certied it across dierent products as well as manufactures. The process is just as easy as pressing a button for the Push-Button Method, or correctly entering the 8-digit code for the Pin Code Method. The time reduction in setup and ease of use are quite benecial, while the highest wireless security setting of WPA2 is automatically used.
70D-Link DIR-655 User ManualSection 3 - CongurationThe wizard will either display the wireless network settings to guide you through manual conguration, prompt you to enter the PIN for the device, or ask you to press the conguration button on the device. If the device supports Wi-Fi Protected Setup and has a conguration button, you can add it to the network by pressing the conguration button on the device and then the on the router within 60 seconds. The status LED on the router will ash three times if the device has been successfully added to the network.There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A registrar only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the device. The router acts as a registrar for the network, although other devices may act as a registrar as well.Click to start the Add Wireless Device wizard.Add Wireless Station:Add Wireless Device with WPS:
71D-Link DIR-655 User ManualSection 3 - CongurationTo use the Universal Plug and Play (UPnP) feature click on Enabled. UPnP provides compatibility with networking equipment, software and peripherals.Checking the box will allow the DIR-655 to respond to pings. Unchecking the box may provide some extra security from hackers.Select from the drop-down menu if you would like to apply the Inbound Filter to the WAN ping. Refer to the Inbound Filters section for more information.You may set the port speed of the Internet port to 10Mbps, 100Mbps, 1000Mbps or Auto (recommended). Check the box to allow multicast trac to pass through the router from the Internet (IPv4).Check the box to allow multicast trac to pass through the router from the Internet (IPv6).Enable UPnP:WAN Ping:WAN Ping Inbound Filter:WAN Port Speed:Enable IPV4 Multicast Streams:Enable IPV6 Multicast Streams:Advanced Network Settings
72D-Link DIR-655 User ManualSection 3 - CongurationGuest ZoneCheck to enable the Guest Zone feature. The schedule of time when the Guest Zone will be active. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section or click Add New.Enter a wireless network name (SSID) that is dierent from your main wireless network.Check to allow network connectivity between the dierent zones created. Select the type of security or encryption you would like to enable for the Guest Zone. Enable Guest Zone:Schedule:Wireless Network Name:Enable Routing Between Zones:Security Mode:The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate from your main wireless network.
73D-Link DIR-655 User ManualSection 3 - CongurationIPv6 FirewallThe DIR-655’s IPv6 Firewall feature allows you to congure which kind of IPv6 trac is allowed to pass through the device. The DIR-655’s IPv6 Firewall functions in a similar way to the Inbound Filters feature.Check to enable the IPv6 rewall simple security.Check to enable IPv6 ingress lter.Select an action from the drop-down menu.Enter a name to identify the IPv6 Firewall Rule.Use the drop-down menu to select the time schedule that the IPv6 Firewall Rule will be enabled on. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section. Use the Source drop-down menu to specify the interface that connects to the source IPv6 addresses of the rewall rule. Enter the source IPv6 address range in the adjacent IP Address Range eld.Use the Dest drop-down menu to specify the interface that connects to the destination IP addresses of the rewall rule. Select the protocol of the rewall port (All, TCP, UDP or ICMP).Enter the rst port of the range that will be used for the rewall rule in the rst box and enter the last port in the eld in the second box.Enable IPv6 Simple Security:Enable IPv6 Ingress Filtering:Congure IPv6 Firewall:Name:Schedule:Source:IP Address Range:Dest: Protocol:Port Range:
74D-Link DIR-655 User ManualSection 3 - CongurationIPv6 RoutingCheck the box next to the route you wish to enable. Enter a specic name to identify this route.Enter the IP address of the router that will be used to reach the specied destination or enter the IPv6 address prex length of the packets that will take this route. Enter the metric value for this rule here.Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the router.Enter the next hop that will be taken if this route is used.Route List:Name:Destination IP/Prex Length:Metric:Interface:Gateway:The IPv6 Routing section allows you to specify custom routes that determine how data is moved around your network.
75D-Link DIR-655 User ManualSection 3 - CongurationAdminTools will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser: admin and user. Admin has read/write access, while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.ToolsEnter a new password for the Administrator Login Name. The Administrator can make changes to the settings.Enter the new password for the User Login. If you login as the User, you cannot change the settings (you can only view them).Enter a name for your router.Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your router’s network settings.Check to enable HTTPS to connect to the router securely. This means to connect to the router you must enter https://192.168.0.1 (for example) instead of http://192.168.0.1. Remote Management allows the DIR-655 to be congured from the Internet by a web browser. A username/password is still required to access the Web Management interface. The port number used to access the DIR-655 is used in the URL. Example: http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-655 and 8080 is the port used for the Web Management interface.If you have enabled HTTPS Server, you must enter https:// as part of the URL to access the router remotely.This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule. Details will display the current status.Admin Password:User Password:System Name:Enable Graphical Authentication:Enable HTTPS Server:Enable Remote Management:Remote Admin Port:Remote Admin Inbound Filter:
76D-Link DIR-655 User ManualSection 3 - CongurationTimeDisplays the current date and time of the router.Select your Time Zone from the drop-down menu.To enable Daylight Saving time manually, check the box and enter a start date and an end date for daylight saving time.NTP is short for Network Time Protocol. A NTP server will sync the time and date with your router. This will only connect to a server on the Internet, not a local server. Check the box to enable this feature.Enter the IP address of a NTP server or select one from the drop-down menu.To manually input the time, enter the values in these elds for the Year, Month, Day, Hour, Minute and Second and then click Set Time. You can also click Copy Your Computer’s Time Settings to synch the date and time with the computer you are currently on.Time:Time Zone:Enable Daylight Saving:Enable NTP Server:NTP Server Used:Manual:The Time Conguration section allows you to congure, update and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be congured to automatically adjust the time when needed.
77D-Link DIR-655 User ManualSection 3 - CongurationSysLogThe DIR-655 keeps a running log of events and activities occurring. You may send these logs to a SysLog server on your network.Enable Logging to SysLog Server:SysLog Server IP Address:Check this box to send the router logs to a SysLog server.The address of the SysLog server that will be used to send the logs. You may also select your computer from the drop-down menu (only if receiving an IP address from the router via DHCP).
78D-Link DIR-655 User ManualSection 3 - CongurationE-mail SettingsThe E-mail Settings feature can be used to send the system log les, router alert messages, and rmware update notication to your e-mail address. Enable E-mail Notication: From E-mail Address:To E-mail Address:SMTP Server Address:SMTP Server Port:Enable Authentication:Account Name:Password:On Log Full:On Schedule:Schedule:When this option is enabled, router activity logs are e-mailed to a designated e-mail address.This e-mail address will appear as the sender when you receive a log le or rmware upgrade notication via e-mail.Enter the e-mail address where you want the e-mail sent. Enter the SMTP server address for sending e-mail. Enter the SMTP port used on the server.Check this box if your SMTP server requires authentication. Enter your account for sending e-mail.Enter the password associated with the account. Re-type the password associated with the account.When this option is selected, logs will be sent via e-mail to your account when the log is full.Selecting this option will send the logs via e-mail according to schedule.This option is enabled when On Schedule is selected. You can select a schedule from the list of dened schedules. To create a schedule, go to Tools > Schedules.
79D-Link DIR-655 User ManualSection 3 - CongurationUse this option to save the current router conguration settings to a le on the hard disk of the computer you are using. First, click the Save button. A le dialog will appear, allowing you to select a location and le name for the settings. Use this option to load previously saved router conguration settings. First, use the Browse option to nd a previously saved le of conguration settings. Then, click the Load button to transfer those settings to the router. This option will restore all conguration settings back to the settings that were in eect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router conguration settings, use the Save button above. Click to reboot the router.Save Settings to Local Hard Drive:Load Settings from Local Hard Drive:Restore to Factory Default Settings:Reboot Device:SystemThe System Settings section allows you to manage the router’s conguration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
80D-Link DIR-655 User ManualSection 3 - CongurationFirmwareBrowse:Upload:After you have downloaded the new rmware, click Browse to locate the rmware update on your hard drive. Click Upload to complete the rmware upgrade.Once you have a rmware update on your computer, use this option to browse for the le and then upload the information into the router. The Firmware Update section allows you to upgrade the rmware of the DIR-655. Make sure the rmware you want to use is on the local hard drive of the computer. Click on Browse to locate the rmware le to be used for the update. Please check the D-Link support website for rmware updates at http://support.dlink.com. You can download rmware upgrades to your hard drive from this site.After you have downloaded the new language pack, click Choose File to locate the language pack le on your hard drive. Click Upload to complete the language pack upgrade.You can change the language of the web UI by uploading available language packs.Choose File:Language Pack Upgrade:
81D-Link DIR-655 User ManualSection 3 - CongurationDynamic Domain Name System is a method of keeping a domain name linked to a changing IP address. Check the box to enable DDNS.Select your DDNS provider from the drop-down menu or enter the DDNS server address.Enter the host name that you registered with your DDNS service provider.Enter the username or key for your DDNS account.Enter the password or key for your DDNS account.Enter a timeout time (in hours).Displays the current connection status.Enable Dynamic DNS:Server Address:Host Name:Username or Key:Password or Key:Timeout:Status:Dynamic DNSThe Dynamic DNS feature allows you to host a server (web, FTP, game server, etc.) using a domain name that you have purchased (i.e. www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet service providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
82D-Link DIR-655 User ManualSection 3 - CongurationThe Ping Test is used to send ping packets to test if a computer is on the Internet. Enter the IP address that you wish to test and click Ping.Enter the IPv6 address that you wish to ping and click Ping.The results of your ping attempts will be displayed here.System CheckPing Test:IPv6 Ping Test:Ping Results:
83D-Link DIR-655 User ManualSection 3 - CongurationEnter a name for your new schedule.Select a day, a range of days, or All Week to include every day.Check All Day - 24hrs or enter a start and end time for your schedule.You must click Save Settings at the top for your schedules to go into eect.The list of schedules will be listed here. Click the Edit icon to make changes or click the Delete icon to remove the schedule.Name:Days:Time:Save:Schedule Rules List:SchedulesSchedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3 p.m. to 8 p.m., you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3 p.m. and End Time of 8 p.m.
84D-Link DIR-655 User ManualSection 3 - CongurationThe Device Info page displays the current information for the DIR-655. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.Displays the router’s time and rmware version.Displays the MAC address and the public IP settings Displays the MAC address and the private (local) IP settings for the router.Displays the 2.4GHz wireless MAC address and your wireless settings such as SSID and Channel. Displays computers and devices that are connected to the router via Ethernet and that are receiving an IP address assigned by the router (DHCP). General:WAN:LAN:Wireless LAN1:LAN Computers:Device InfoStatus
85D-Link DIR-655 User ManualSection 3 - CongurationLogsLog Options:Refresh:First Page:Last Page:Previous:Next:Clear:E-mail Now:Save Log:You can select the types of messages that you want to display from the log. System Activity, Debug Information, Attacks, Dropped Packets, and Notice messages can be selected. Click Apply Log Settings Now to activate your settings.Updates the log details on the screen so it displays any recent activity.Click to go to the rst page.Click to go to the last page.Click to go back one page.Click to go to the next page.Clears all of the log contents.This option will send a copy of the router log to your e-mail address congured in the Tools > E-mail Settings screen.This option will save the router log to a le on your computer.The router automatically logs (records) events of possible interest in its internal memory. The Logs option allows you to view the router logs. If there isn’t enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained. You can dene what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log les to a computer on your network that is running a Syslog utility.
86D-Link DIR-655 User ManualSection 3 - CongurationStatisticsThe screen below displays the Trac Statistics. Here you can view the amount of packets that pass through the DIR-655 on both the WAN, LAN ports and the wireless segments. The trac counter will reset if the device is rebooted.
87D-Link DIR-655 User ManualSection 3 - CongurationInternet SessionsThe Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
88D-Link DIR-655 User ManualSection 3 - CongurationRoutingThis page will display your current routing table.
89D-Link DIR-655 User ManualSection 3 - CongurationThe Wireless Client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.Wireless
90D-Link DIR-655 User ManualSection 3 - CongurationIPv6The IPv6 page displays a summary of the router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
91D-Link DIR-655 User ManualSection 3 - CongurationIPv6 RoutingThis page displays the IPv6 Routing details congured for your router.
92D-Link DIR-655 User ManualSection 3 - CongurationSupport
93D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterConnect a Wireless Client to your RouterWPS ButtonStep 2 - Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process).The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can press to connect to the DIR-655 router. Please refer to your user manual for the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:Step 1 - Press the WPS button on the DIR-655 for about 1 second. The Internet LED on the front will start to blink.Step 3 - Allow up to 1 minute to congure. Once the Internet light stops blinking, you will be connected and your wireless connection will be secure with WPA2.WPS Button
94D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterWindows® 8WPA/WPA2It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used.To join an existing network, locate the wireless network icon in the taskbar, next to the time display. Wireless IconClicking on this icon will display a list of wireless networks which are within connecting proximity of your computer. Select the desired network by clicking on the network name.
95D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterYou will then be prompted to enter the network security key (Wi-Fi password) for the wireless network. Enter the password into the box and click Next. If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router, you can also press the WPS button on your router at the point to enable the WPS function. When you have established a successful connection a wireless network, the word Connected will appear next to the name of the network to which you are connected.
96D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterWindows® 7It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.1. Click on the wireless icon in your system tray (lower-right corner).2. The utility will display any available wireless networks in your area.Wireless IconWPA/WPA2
97D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your Router3. Highlight the wireless connection with Wi-Fi name (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.4. The following window appears while your computer tries to connect to the router.
98D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your Router5. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. You can also connect by pushing the WPS button on the router.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
99D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterWPSThe WPS feature of the DIR-655 can be congured using Windows® 7. Carry out the following steps to use Windows® 7 to congure the WPS feature:1. Click the Start button and select Computer from the Start menu.2. Click Network on the left side.
100D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your Router3. Double-click the DIR-655.4. Input the WPS PIN number (on the Router label) or in the Setup > Wireless Setup menu in the Router’s Web UI and click Next.
101D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your Router5. Type a name to identify the network.6. To congure advanced settings, click the icon.Click Next to continue.
102D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your Router7. The following window appears while the router is being congured. Wait for the conguration to complete.8. The following window informs you that WPS on the router has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future.9. Click Close to complete WPS setup.
103D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterWindows Vista®Windows Vista users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below.Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network.If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. orThe utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.
104D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterWPA/WPA2It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.2. Highlight the Wi-Fi name (SSID) you would like to connect to and click Connect.1. Open the Windows Vista Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network.
105D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your Router3. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
106D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterWPS/WCN 2.0The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista. The following instructions for setting this up depends on whether you are using Windows Vista to congure the router or third party software. When you rst set up the router, Wi-Fi protection is disabled and uncongured. To enjoy the benets of Wi-Fi protection, the router must be both enabled and congured. There are three basic methods to accomplish this: use Windows Vista’s built-in support for WCN 2.0, use software provided by a third party, or manually congure. If you are running Windows Vista, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click the Generate New PIN button or Reset PIN to Default button. If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are nished, proceed to the next section to set up the newly-congured router.
107D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterWindows® XPWindows XP users may use the built-in wireless utility (Zero Conguration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks.If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. orThe utility will display any available wireless networks in your area. Click on a Wi-Fi network (displayed using the SSID) and click the Connect button.If you get a good signal but cannot access the Internet, check you TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.
108D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your RouterIt is recommended to enable WPA on your wireless router or access point before conguring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used.2. Highlight the Wi-Fi network (SSID) you would like to connect to and click Connect.1. Open the Windows XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. WPA/WPA2
109D-Link DIR-655 User ManualSection 4 - Connect a Wireless Client to your Router3. The Wireless Network Connection box will appear. Enter the WPA-PSK Wi-Fi password and click Connect.It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The Wi-Fi password must be exactly the same as on the wireless router.
110D-Link DIR-655 User ManualSection 5 - TroubleshootingTroubleshootingThis chapter provides solutions to problems that can occur during the installation and operation of the DIR-655. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a dierent operating system, the screenshots on your computer will look similar to the following examples.)1. Why can’t I access the web-based conguration utility?When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. • Make sure you have an updated Java-enabled web browser. We recommend the following: • Internet Explorer 6.0 or higher • Netscape 8 or higher • Mozilla 1.7.12 (5.0) or higher • Opera 8.5 or higher • Safari 1.2 or higher (with Java 1.3.1 or higher) • Camino 0.8.4 or higher • Firefox 1.5 or higher • Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a dierent cable or connect to a dierent port on the device if possible. If the computer is turned o, the link light may not be on.• Disable any internet security software running on the computer. Software rewalls such as ZoneAlarm, BlackICE, Sygate, Norton Personal Firewall, and Windows XP rewall may block access to the conguration pages. Check the help les included with your rewall software for more information on disabling or conguring it.
111D-Link DIR-655 User ManualSection 5 - Troubleshooting• Congure your Internet settings:• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults.• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.• Close your web browser (if open) and open it.• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your the web management. • If you still cannot access the conguration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the conguration. If you have multiple computers, try connecting using a dierent computer.2. What can I do if I forgot my password?If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.
112D-Link DIR-655 User ManualSection 5 - Troubleshooting3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To nd the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL. • Click on Start and then click Run. • Windows® 95, 98, and Me users type in command (Windows NT, 2000, XP, Vista® and 7 users type in cmd) and press Enter (or click OK). • Once the window opens, you’ll need to do a special ping. Use the following syntax: ping [url] [-f] [-l] [MTU value] Example: ping yahoo.com -f -l 1472
113D-Link DIR-655 User ManualSection 5 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you nd your MTU, you can now congure your router with the proper MTU size. To change the MTU rate on your router follow the steps below: • Open your browser, enter the IP address of your router (192.168.0.1) and click OK. • Enter your username (admin) and password (blank by default). Click OK to enter the web conguration page for the device. • Click on Setup and then click Manual Congure. • To change the MTU enter the number in the MTU eld and click Save Settings to save your settings. • Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten.
114D-Link DIR-655 User ManualAppendix A - Wireless BasicsD-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and oce environments, and public areas such as airports, coee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more eciently. Increased mobility and the absence of cabling and other xed infrastructure have proven to be benecial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A wireless router is a device used to provide this link.Wireless BasicsWhat is Wireless?Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or oce network.Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can aord. D-Link has all the products you need to build your network.
115D-Link DIR-655 User ManualAppendix A - Wireless BasicsHow does wireless work? Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two dierent types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN).Wireless Local Area Network (WLAN)In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.Wireless Personal Area Network (WPAN)Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away.Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, oce, business, D-Link has a wireless solution for it.Home • Gives everyone at home broadband access • Surf the web, check email, instant message, and etc • Gets rid of the cables around the house • Simple and easy to use Small Oce and Home Oce • Stay on top of everything at home as you would at oce • Remotely access your oce network from home • Share Internet connection and printer with multiple computers • No need to dedicate oce space
116D-Link DIR-655 User ManualAppendix A - Wireless BasicsWhere is wireless used? Wireless technology is expanding everywhere not just at home or oce. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.Using a D-Link CardBus adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: airports, hotels, coee shops, libraries, restaurants, and convention centers.Wireless network is easy to setup, but if you’re installing it for the rst time it could be quite a task not knowing where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.TipsHere are a few things to keep in mind, when you install a wireless network.Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range.Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would signicantly reduce any interference that the appliances might cause since they operate on same frequency.Security Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA security feature on the router. Refer to product manual for detail information on how to set it up.
117D-Link DIR-655 User ManualAppendix A - Wireless BasicsThere are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-655 wireless network CardBus adapters.An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate.Wireless Modes
118D-Link DIR-655 User ManualAppendix B - Networking BasicsNetworking BasicsCheck your IP addressAfter you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.Click on Start > Run. In the run box type cmd and click OK. (Windows Vista® users type cmd in the Start Search box.)At the prompt, type ipcong and press Enter.This will display the IP address, subnet mask, and the default gateway of your adapter.If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some rewall software programs may block a DHCP request on newly installed adapters. If you are connecting to a wireless network at a hotspot (e.g. hotel, coee shop, airport), please contact an employee or administrator to verify their wireless network settings.
119D-Link DIR-655 User ManualAppendix B - Networking BasicsStatically Assign an IP addressIf you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:Step 1Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center.Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.Windows XP - Click on Start > Control Panel > Network Connections.Windows 2000 - From the desktop, right-click My Network Places > Properties.Step 2Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.Step 3Highlight Internet Protocol (TCP/IP) and click Properties.Step 4Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.Step 5Click OK twice to save your settings.
120D-Link DIR-655 User ManualAppendix C - Technical SpecicationsTechnical SpecicationsStandards • IEEE 802.11n • IEEE 802.11g • IEEE 802.3 • IEEE 802.3uSecurity • WPA-Personal • WPA2-Personal • WPA-Enterprise • WPA2-Enterprise Wireless Signal Rates1 • 6.5 Mbps ~ 300 Mbps Frequency Range • 2.4 GHz to 2.483 GHz2External Antenna Type • Three (3) detachable reverse SMA AntennasOperating Temperature • 32°F to 131°F ( 0°C to 55°C)Humidity • 95% maximum (non-condensing)Safety & Emissions • FCC • CE • ICDimensions • L = 7.6 inches • W = 4.6 inches • H = 1.2 inchesWarranty • 2 years1 Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely aect wireless signal range.2 Wireless frequency range may vary depending on region
121D-Link DIR-655 User ManualAppendix D - Safety StatementsCE Mark Warning:This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.FCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTICE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The availability of some specic channels and/or operational frequency bands are country dependent and are rmware programmed at the factory to match the intended destination. The rmware setting is not accessible by the end user.
122D-Link DIR-655 User ManualAppendix D - Safety StatementsFor detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link oce.Industry Canada Notice:This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. IMPORTANT NOTE:Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device has been designed to operate with an antenna having a maximum gain of 2dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.Déclaration d’exposition aux radiations:Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This radio transmitter(IC: 4216A-IR655C1) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Cet émetteur radio (IC: 4216A-IR655C1) a été approuvé par Industrie Canada pour fonctionner avec les types d’antennes énumérés ci-dessous avec le gain maximal admissible et nécessaire impédance d’antenne pour chaque type d’antenne indiqué. Types d’antennes ne gurent pas dans cette liste, ayant un gain supérieur au gain maximum indiqué pour ce type, sont strictement interdites pour une utilisation avec cet appareil. “To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication”
123D-Link DIR-655 User ManualAppendix D - Safety Statements“This device has been designed to operate with an antenna having a maximum gain of [2] dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.” «Pour réduire le risque d’interférence avec d’autres utilisateurs, le type d’antenne et son gain doivent être choisis an que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie”«Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de [2] dBi. Antenne ayant un gain supérieur sont strictement interdites par la réglementation d’Industrie Canada. L’impédance d’antenne requise est de 50 ohms.”

Navigation menu