D Link IR819A1 Wireless AC750 Dual Band Router User Manual

D Link Corporation Wireless AC750 Dual Band Router Users Manual

Users Manual

Download: D Link IR819A1 Wireless AC750 Dual Band Router User Manual
Mirror Download [FCC.gov]D Link IR819A1 Wireless AC750 Dual Band Router User Manual
Document ID3233586
Application ID5CqpqQgiA/L7nV4vJGBoWA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize301.79kB (3772359 bits)
Date Submitted2016-12-20 00:00:00
Date Available2016-12-27 00:00:00
Creation Date2016-11-04 10:32:00
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2016-11-04 10:33:19
Document TitleUsers Manual
Document CreatorAdobe InDesign CC 2017 (Windows)

Version 1.01 | 11/04/2016
User Manual
Wireless AC750 Dual Band Router
DIR-819
Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization
of such revisions or changes.
Manual Revisions
Revision
Date
1.0
28 October, 2016
Description
Initial release for revision A1
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Internet Explorer®, Windows® and the Windows logo are trademarks of the Microsoft group of companies.
Copyright © 2016 by D-Link Corporation, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation, Inc.
The purpose of this product is to create a constant network connection for your devices. As such, it does not have a standby mode or use a power
management mode. If you wish to power down this product, please simply unplug it from the power outlet.
D-Link DIR-819 User Manual
Table of Contents
Table of Contents
Package Contents............................................................... 1
System Requirements.................................................................. 2
Introduction.................................................................................... 3
Features............................................................................................. 4
Hardware Overview...................................................................... 5
LEDs............................................................................................ 5
Connections............................................................................ 6
Installation.......................................................................... 7
Before You Begin............................................................................ 7
Wireless Installation Considerations....................................... 8
Hardware Setup............................................................................. 9
Completing Setup.......................................................................12
Setup Wizard.................................................................................13
Configuration....................................................................21
Web UI Table of Contents.........................................................22
Setup................................................................................................23
Internet....................................................................................24
Internet Connection Setup Wizard...........................25
Manual Internet Connection Setup.........................33
Wireless Settings..................................................................43
Wireless Connection Setup Wizard..........................44
Add Wireless Device with WPS...................................47
Manual Wireless Connection Setup.........................50
Wireless Security Mode................................................52
Network Settings.................................................................54
IPv6...........................................................................................57
D-Link DIR-819 User Manual
IPv6 Internet Connection Setup Wizard.................58
IPv6 Local Connectivity Settings...............................62
Manual IPv6 Internet Connection Setup................63
Advanced.......................................................................................79
Virtual Server.........................................................................80
Port Forwarding...................................................................81
Application Rules.................................................................82
QOS Engine............................................................................83
Network Filter.......................................................................85
Inbound Filter.......................................................................86
Access Control......................................................................87
Add Policy..........................................................................88
Website Filter.........................................................................91
Firewall Settings...................................................................92
Routing....................................................................................94
Advanced Wireless..............................................................95
Wi-Fi Protected Setup........................................................96
Advanced Network.............................................................97
Guest Zone.............................................................................98
IPv6 Firewall...........................................................................99
IPv6 Routing....................................................................... 101
Tools.............................................................................................. 102
Admin................................................................................... 103
Time....................................................................................... 104
Syslog.................................................................................... 105
System.................................................................................. 106
Firmware.............................................................................. 107
ii
Table of Contents
Dynamic DNS..................................................................... 108
System Check..................................................................... 109
Schedules............................................................................ 110
Status............................................................................................ 111
Device Info.......................................................................... 112
Logs....................................................................................... 114
Statistics............................................................................... 115
Internet Sessions............................................................... 116
Wireless................................................................................ 117
Routing................................................................................. 118
IPV6........................................................................................ 119
IPv6 Routing....................................................................... 120
Support........................................................................................ 121
Wireless Modes.......................................................................... 144
Networking Basics..........................................................145
Check your IP address............................................................. 145
Statically Assign an IP address............................................. 146
Wireless Security.......................................................... 147
What is WPA?................................................................. 147
Technical Specifications.................................................148
Regulatory Information.................................................149
Connect a Wireless Client to Your Router......................122
WPS Button................................................................................. 122
Windows® 10.............................................................................. 123
Windows® 8................................................................................. 125
WPA/WPA2.......................................................................... 125
Windows® 7................................................................................. 127
WPA/WPA2.......................................................................... 127
WPS........................................................................................ 129
Windows Vista®.......................................................................... 133
WPA/WPA2.......................................................................... 134
Troubleshooting.............................................................136
Wireless Basics................................................................140
What is Wireless?....................................................................... 141
Tips................................................................................................. 143
D-Link DIR-819 User Manual
iii
Section 1 - Product Overview
Package Contents
DIR-819 Wireless AC750 Dual Band Router
Power Adapter
Ethernet Cable
Wi-Fi Configuration Card
Quick Install Guide
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a different voltage rating than the one included with the DIR-819 will cause damage and void the warranty
for this product.
D-Link DIR-819 User Manual
Section 1 - Product Overview
System Requirements
Network Requirements
• An Ethernet-based cable or DSL modem
• IEEE 802.11ac, 802.11n, 802.11a, 802.11g, or 802.11b wireless clients
• 10/100 Ethernet
Computer with the following:
• Windows®, Macintosh, or Linux-based operating system
• An installed Ethernet adapter
Web-based Configuration
Utility Requirements
Browser Requirements:
• Internet Explorer 9 or higher
• Firefox 20 or higher
• Safari 5.1 or higher
• Chrome 25 or higher
Windows® Users: Make sure you have the latest version of Java installed.
Visit www.java.com to download the latest version.
D-Link DIR-819 User Manual
Section 1 - Product Overview
Introduction
The D-Link DIR-819 Wireless AC750 Dual Band Router shares your Internet connection over a blazing-fast wireless connection of up to 750 Mbps
(up to 433 Mbps over 5 GHz Wireless AC and up to 300 Mbps over 2.4 GHz Wireless N)1, using advanced AC beamforming technology to significantly
outperform 802.11n and other 802.11ac devices. Equipped with one Fast Ethernet WAN/Internet port and four Fast Ethernet LAN ports, the DIR-819
creates an excellent networking experience.
Featuring four antennas, the Wireless AC750 Dual Band Router offers better data rates, fewer dead-spots, more coverage, and higher reliability.
Operating exclusively in the 5 GHz band, the DIR-819’s 802.11ac wireless connections avoid the crowded 2.4 GHz band, giving you faster speeds while
still maintaining backwards compatibility with older 802.11n/g/b devices. A stronger Wi-Fi signal means you can install more wireless surveillance
cameras, baby monitors, sensors, and alarms in the places where you need them.
The DIR-819 supports the latest security features to help prevent unauthorized access. Support for WPA™ and WPA2™ standards ensure that you
will be able to use the best possible encryption regardless of your client devices. This router is also equipped with a dual-active firewall (SPI and
NAT) to prevent potential attacks over the Internet.
The DIR-819 is full of features to improve your home network. The rich parental controls allow you to easily control when the Internet should be
available in your home and what content is allowed. With all this and more, the DIR-819 Wireless AC750 Dual Band Router will serve your network
well for years to come.
1 Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, 802.11n and 802.11ac specifications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.
D-Link DIR-819 User Manual
Section 1 - Product Overview
Features
• Excellent Wireless Networking - The DIR-819 provides wireless speeds of up to a combined 750 Mbps (433 Mbps 802.11ac 5 GHz, plus
300 Mbps 802.11n 2.4 GHz)1. This capability rivals wired connections, allowing users to participate in real-time activities online, such
as HD video communication, online gaming, and use mobile devices from anywhere in your home while still offering full 802.11n/g/b
backward compatibility.
•
Fast Wired LAN and WAN Networking - With four 10/100 Fast Ethernet LAN ports, and a 10/100 Fast Ethernet WAN port, the DIR-819
has an enormous amount of bandwidth to take full advantage of the highest speed broadband connections available.
•
IPv6 Support - The DIR-819 fully supports IPv6 and includes support for a variety of IPv6 connection types including: SLAAC/DHCPv6,
6to4, 6rd, Static IPv6, IPv6 PPPoE, IPv6 in IPv4 tunneling, and local connectivity.
•
Advanced Firewall Features - The web-based user interface displays a number of advanced network management features. Easily
apply content filtering based on MAC address, URL, and/or domain name. Schedule these filters to be active on certain days or for a
duration of hours or minutes.
•
Secure Multiple/Concurrent Sessions - The DIR-819 can pass through VPN sessions. It supports multiple and concurrent IPSec and
PPTP sessions, so users behind the DIR-819 can securely access corporate networks.
•
User-friendly Setup Wizard - Through its easy-to-use web-based user interface, the DIR-819 lets you quickly configure and secure
your router to your specific settings in minutes.
Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, 802.11n and 802.11ac specifications. Actual data throughput will vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data
throughput rate. Environmental conditions will adversely affect wireless signal range.
D-Link DIR-819 User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
Power
The Power LED indicates that the device is powered on with a proper connection to the power supply.
2.4 GHz Wireless
The Wireless LED indicates that this wireless band is working. It blinks during wireless data transmission.
5 GHz Wireless
The Wireless LED indicates that this wireless band is working. It blinks during wireless data transmission.
Internet
WPS
D-Link DIR-819 User Manual
The Internet LED indicates that an Internet link is established. It blinks during data transmission.
The WPS LED blinks during the WPS pairing process.
Section 1 - Product Overview
Hardware Overview
Connections
Reset Button
Insert a paperclip in the hole, wait for 10 seconds, and release to reset the router to default settings.
Power Button
Press the power button to power the device on and off.
Power Connector
WPS Button
Press to start the WPS process and automatically create a secure connection to a WPS client.
Internet Port
Using an Ethernet cable, connect your broadband modem to this port.
LAN Ports (1-4)
D-Link DIR-819 User Manual
Connector for the supplied power adapter.
Connect Ethernet devices such as computers, switches, storage (NAS) devices and game consoles.
Section 2 - Installation
Installation
Before You Begin
• Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, attic, or garage.
• Configure the router with the computer that was last connected directly to your Internet connection. Verify that it is connected to
the Internet before connecting additional devices.
• If your ISP provided you with a modem/router combo, you will need to set it to “bridge” mode so the router can work properly. Please
contact your Internet Service Provider (ISP) or refer to the user manual for your modem/router device.
• You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must
turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the
modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
• If connecting to a DSL modem, make sure to have your DSL service information provided by your Internet Service Provider handy.
This information is likely to include your DSL account's username and password. Your ISP may also supply you with additional WAN
configuration settings which might be necessary to establish a connection.
• If you are connecting a considerable amount of networking equipment, it may be a good idea to take the time to label each cable
or take a picture of your existing setup before making any changes.
• If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoET, BroadJump,
or EnterNet 300 from your computer or you will not be able to connect to the Internet.
D-Link DIR-819 User Manual
Section 2 - Installation
Wireless Installation Considerations
This D-Link wireless device lets you access your network using a wireless connection from virtually anywhere within the operating range of your
wireless network. Keep in mind that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through
may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling
can reduce your adapter’s range from 1 to 30 meters (3 to 90 feet). Position your devices so that the number of walls or ceilings is
minimized.
2. Be aware of the direct line between network devices. A wall that is 0.5 meters (1.5 feet) thick, at a 45-degree angle appears to be
almost 1 meter (3 feet) thick. At a 2-degree angle it looks over 14 meters (42 feet) thick! Position devices so that the signal will
travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position
access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects
such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your
wireless signal.
4. Keep your product away at least 1 to 2 meters (3 to 6 feet) from electrical devices or appliances that generate RF noise.
5. If you are using 2.4 GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your
wireless connection may degrade dramatically or drop completely. Make sure your 2.4 GHz phone base is as far away from your
wireless devices as possible. The base transmits a signal even if the phone is not in use.
D-Link DIR-819 User Manual
Section 2 - Installation
Hardware Setup
1. The DIR-819 is designed to give you the fastest, most stable network connection possible. In order to maximize performance, fully extend
the antennas to provide optimal wireless coverage. Keep the router in an open area for better wireless coverage.
DIR-819
2. Position your DIR-819 near your Internet-connected modem. Place it in an open area for better wireless coverage.
DIR-819
Modem
3. Turn off and unplug the power and Ethernet cable to your cable or DSL broadband modem. This is required. In some cases, you may need
to turn it off for up to five minutes.
DIR-819
D-Link DIR-819 User Manual
Modem
Section 2 - Installation
Hardware Setup (continued)
4. Use the included Ethernet cable to connect your modem to the yellow port labeled INTERNET on the router.
Modem
DIR-819
RESET POWER POWER PORT
WPS
INTERNET
5. Turn on or plug your modem back in and wait approximately one minute before proceeding onward.
Modem
DIR-819
RESET POWER POWER PORT
WPS
INTERNET
6. Connect the supplied power adapter to the router and a power outlet, press the power button, and verify that the power LED is lit. Allow
1 minute for the router to boot up.
Modem
DIR-819
D-Link DIR-819 User Manual
RESET POWER POWER PORT
WPS
INTERNET
10
Section 2 - Installation
Hardware Setup (continued)
7. If you are configuring the DIR-819 wirelessly from a PC, connect to a Wi-Fi network printed on the included Wi-Fi configuration card. You
can also find the Wi-Fi network names and passwords printed on the label attached to the bottom of your router.
DIR-819
Modem
Wi-Fi Configuration Card
RESET POWER POWER PORT
WPS
INTERNET
If you are configuring the DIR-819 from a PC with a wired Ethernet connection, plug one end of an Ethernet cable into the port labeled
1 on the back of the router, and the other end into the Ethernet port on your computer.
DIR-819
Modem
RESET POWER POWER PORT
WPS
INTERNET
8. If you are connecting to a broadband service that uses a dynamic connection (not PPPoE), you may be online already. Try opening a web
browser and connecting to a website. If the website does not load, proceed to Completing Setup on page 12.
D-Link DIR-819 User Manual
11
Section 2 - Installation
Completing Setup
There are several different ways you can configure your router to connect to the Internet and connect to your clients:
• D-Link Setup Wizard - This wizard will launch when you log into the router for the first time, refer to Setup Wizard on page 13.
• Manual Setup - Log into the router and manually configure your router, refer to Configuration on page 21.
D-Link DIR-819 User Manual
12
Section 2 - Installation
Setup Wizard
If this is your first time installing the router, open your web browser and enter
http://dlinkrouter.local./ in the address bar. Alternatively, enter the IP address of the router
(default: http://192.168.0.1). The first time you log in, the setup wizard will run.
WELCOME TO THE D-LINK SETUP WIZARD
The wizard is designed to guide you through a step-by-step process to configure your new
D-Link router and connect to the Internet.
WELCOME TO THE D-LINK SETUP WIZARD
This wizard will guide you through a step-by-step process to configure your new D-Link router and connect to the
Internet.
•
•
•
•
•
Step 1: Configure your Internet Connection
Step 2: Configure your Wi-Fi Security
Step 3: Set your Password
Step 4: Select your Time Zone
Step 5: Confirm Wi-Fi Settings
Cancel
Next
Click Next to continue.
D-Link DIR-819 User Manual
13
Section 2 - Installation
Step 1 - Configure Your Internet Connection
STEP 1: CONFIGURE YOUR INTERNET CONNECTION
STEP 1: CONFIGURE YOUR INTERNET CONNECTION
The router is detecting your Internet connection type, please wait...
Please wait while your router attempts to detect your Internet connection type. You may
need to enter information such as your ISP account username and password.
Cancel
Prev
Next
Next to continue.
STEP 1: CONFIGURE YOUR INTERNET CONNECTION
Select the connection type your ISP uses.
STEP 1: CONFIGURE YOUR INTERNET CONNECTION
If your Internet Service Provider was not listed or you don’t know who it is, please select the Internet connection type
below:
ž DHCP Connection (Dynamic IP Address)
Choose this if your Internet connection automatically provides you with an IP Address. Most Cable Modems use this type of
connection.
š Username / Password Connection (PPPoE)
If you select DHCP Connection (Dynamic IP Address), proceed to Step 2 - Configure Your
Wi-Fi Security on page 19.
Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type
of connection.
š Username / Password Connection (PPTP)
PPTP client.
š Username / Password Connection (L2TP)
For Username / Password Connection (PPPoE) setup help refer to page 15.
L2TP client.
š Static IP Address Connection
Choose this option if your Internet Setup Provider provided you with IP Address information that has to be manually configured.
For Username / Password Connection (PPTP) setup help refer to page 15.
Cancel
Prev
Next
For Username / Password Connection (L2TP) setup help refer to page 16.
For Static IP Address Connection setup help refer to page 18.
Select your connection type and click Next to continue.
D-Link DIR-819 User Manual
14
Section 2 - Installation
Username / Password Connection (PPPoE)
If you chose Username / Password Connection (PPPoE) as your Internet Connection, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPPOE)
SET USERNAME AND PASSWORD CONNECTION (PPPOE)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. If you do
not have this information, please contact your ISP.
Username: Enter the username provided by your ISP.
User Name :
Password :
Password: Enter the password provided by your ISP.
Cancel
Prev
Next
Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19.
Username / Password Connection (PPTP)
If you choose Username / Password Connection (PPTP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPTP)
SET USERNAME AND PASSWORD CONNECTION (PPTP)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also
need PPTP IP address. If you do not have this information, please contact your ISP.
Address Mode: Select either Dynamic IP or Static IP
Address Mode : ž Dynamic IP š Static IP
PPTP IP Address :
If you choose Static IP as the Address Mode, enter your IP address:
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address (may be
same as gateway):
PPTP IP Address: Enter the PPTP IP Address provided by your ISP.
User Name :
Password :
PPTP Subnet Enter the PPTP Subnet Mask provided by your ISP.
Mask:
Verify Password :
DNS SETTINGS
Primary DNS Address :
PPTP Gateway IP Enter the PPTP Gateway IP Address provided by your ISP.
Address:
Secondary DNS Address :
Cancel
Prev
Next
If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP
address:
PPTP Server IP Enter the PPTP Server IP address provided by your ISP.
Address:
D-Link DIR-819 User Manual
15
Section 2 - Installation
Username / Password Connection (PPTP) (continued)
User Name: Enter the username provided by your ISP.
SET USERNAME AND PASSWORD CONNECTION (PPTP)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also
need PPTP IP address. If you do not have this information, please contact your ISP.
Password: Enter the password provided by your ISP.
Address Mode : ž Dynamic IP š Static IP
PPTP IP Address :
PPTP Subnet Mask :
Verify Password: Enter the password provided by your ISP one more time.
PPTP Gateway IP Address :
PPTP Server IP Address (may be
same as gateway):
User Name :
Password :
DNS SETTINGS
Primary DNS Enter the primary DNS server IP addresses.
Server:
Verify Password :
DNS SETTINGS
Primary DNS Address :
Secondary DNS Address :
Cancel
Secondary DNS Enter the secondary DNS server IP addresses.
Server:
Prev
Next
Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19.
Username / Password Connection (L2TP)
If you choose Username / Password Connection (L2TP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (L2TP)
SET USERNAME AND PASSWORD CONNECTION (L2TP)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also
need L2TP IP address. If you do not have this information, please contact your ISP.
Address Mode: Select either Dynamic IP or Static IP
Address Mode : ž Dynamic IP š Static IP
L2TP IP Address :
L2TP Subnet Mask :
If you choose Static IP as the Address Mode, enter your IP address:
L2TP Gateway IP Address :
L2TP Server IP Address :
L2TP IP Address: Enter the L2TP IP Address provided by your ISP.
(may be same as gateway)
User Name :
Password :
L2TP Subnet Enter the L2TP Subnet Mask provided by your ISP.
Mask:
Verify Password :
DNS SETTINGS
Primary DNS Address :
Secondary DNS Address :
L2TP Gateway IP Enter the L2TP Gateway IP Address provided by your ISP.
Address:
D-Link DIR-819 User Manual
Cancel
(optional)
Prev
Next
16
Section 2 - Installation
Username / Password Connection (L2TP) (continued)
If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP
address:
SET USERNAME AND PASSWORD CONNECTION (L2TP)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also
need L2TP IP address. If you do not have this information, please contact your ISP.
Address Mode : ž Dynamic IP š Static IP
L2TP IP Address :
L2TP Server IP Enter the L2TP Server IP address provided by your ISP.
Address:
L2TP Subnet Mask :
L2TP Gateway IP Address :
L2TP Server IP Address :
(may be same as gateway)
User Name :
Username: Enter the username provided by your ISP.
Password :
Verify Password :
Password: Enter the password provided by your ISP.
DNS SETTINGS
Primary DNS Address :
Verify Password: Enter the password provided by your ISP one more time.
Secondary DNS Address :
Cancel
(optional)
Prev
Next
DNS SETTINGS
Primary DNS Enter the primary DNS server IP addresses.
Server:
Secondary DNS Enter the secondary DNS server IP addresses.
Server:
Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19.
D-Link DIR-819 User Manual
17
Section 2 - Installation
Static IP Address Connection
If you choose Static IP Address Connection as your Internet Connection, enter your IP address, configure the following settings:
SET STATIC IP ADDRESS CONNECTION
SET STATIC IP ADDRESS CONNECTION
To set up this connection you will need to have a complete list of IP information provided by your Internet Service
Provider. If you have a Static IP connection and do not have this information, please contact your ISP.
IP Address: Enter the IP address provided by your ISP.
IP Address :
Subnet Mask :
Subnet Mask: Enter the subnet mask.
Default Gateway :
DNS SETTINGS
Default Gateway: Enter the default gateway.
DNS SETTINGS
Primary DNS Address :
Secondary DNS Address :
Cancel
(optional)
Prev
Next
Primary DNS Enter the primary DNS server IP addresses.
Server:
Secondary DNS Enter the secondary DNS server IP addresses.
Server:
Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19.
D-Link DIR-819 User Manual
18
Section 2 - Installation
Step 2 - Configure Your Wi-Fi Security
STEP 2: CONFIGURE YOUR WI-FI SECURITY
Wi-Fi Network Enter a name for the 2.4 GHz wireless network.
Name(SSID):
STEP 2: CONFIGURE YOUR WI-FI SECURITY
Give your Wi-Fi network a name and a password. (2.4GHz Band)
Wi-Fi Network Name(SSID) :
Your_2.4GHz_Network
A_Str0ng_P@ssWord!
Wi-Fi Password: Enter a wireless password according to the onscreen guidelines.
(Using up to 32 characters)
Wi-Fi Password :
(Between 8 and 63 characters)
Give your Wi-Fi network a name and a password. (5GHz Band)
Wi-Fi Network Name(SSID) :
Wi-Fi Network Enter a name for the 5 GHz wireless network.
Name(SSID):
Your_5GHz_Network
(Using up to 32 characters)
Wi-Fi Password :
A_Str0ng_P@ssWord!
(Between 8 and 63 characters)
Wi-Fi Password: Enter a wireless password according to the onscreen guidelines.
Cancel
Prev
Next
Click Next to continue.
Step 3: Set Your Password
STEP 3: SET YOUR PASSWORD
STEP 3: SET YOUR PASSWORD
By default, your new D-Link Router does not have a password configured for administrator access to the Web-based
configuration pages. To secure your new networking device, please set and verify a password below:
Enter a new administration password. This is the password you will use to log in to the router.
Password :
Verify Password :
Click Next to continue.
Cancel
Prev
Next
Step 4: Select Your Time Zone
STEP 4: SELECT YOUR TIME ZONE
Select your time zone. Click Next to continue.
STEP 4: SELECT YOUR TIME ZONE
Select the appropriate time zone for your location. This information is required to configure the time-based options for
the router.
Time Zone :
Cancel
D-Link DIR-819 User Manual
(GMT+08:00) Taipei
Prev
▼
Next
19
Section 2 - Installation
Step 5: Confirm Wi-Fi Settings
STEP 5: CONFIRM WI-FI SETTINGS
STEP 5: CONFIRM WI-FI SETTINGS
Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a
piece of paper, so you can configure the correct settings on your Wi-Fi devices.
Step 5 is a summary of your wireless settings. Click Next to finish the wizard.
Wi-Fi Network Name(SSID) 2.4GHz : Your_2.4GHz_Network
Wi-Fi Password A_Str0ng_P@ssWord!
Wi-Fi Network Name(SSID) 5GHz : Your_5GHz_Network
Wi-Fi Password A_Str0ng_P@ssWord!
Cancel
Congratulations, your device has been successfully configured. The router will reboot and
display the login page.
Next
LOGIN
Login to the router :
User Name :
Password :
D-Link DIR-819 User Manual
Prev
Admin
Login
20
Section 3 - Configuration
Configuration
This section will show you how to configure or change the default settings your D-Link
DIR-819 using the web-based configuration utility.
To access the configuration utility, open a web browser such as Internet Explorer and enter
http://dlinkrouter.local./ or you may also connect by typing the IP address of the router
(by default this is http://192.168.0.1) in the address bar.
LOGIN
Login to the router :
User Name :
Admin
Password :
Login
Enter your password. If you previously followed the setup wizard, please use the
admin password you entered during the wizard. Otherwise, leave the password blank.
Click Login to proceed.
Note: If you cannot remember your password and cannot log in, press the reset button on the
back of the device for longer than 10 seconds to restore the router to its default settings.
If you are having trouble logging in or experiencing trouble with the configuration utility,
try clearing your browser cache or try using your web browser’s private browsing mode.
DIR-819
INTERNET
WIRELESS SETTINGS
NETWORK SETTINGS
IPV6
SETUP
ADVANCED
TOOLS
STATUS
SUPPORT
INTERNET CONNECTION
If you are configuring the device for the first time, we recommend that you click on the Internet Connection Setup Wizard, and follow
the instructions on the screen. If you wish to modify or configure the device settings manually, click the Manual Internet Connection
Setup.
INTERNET CONNECTION SETUP WIZARD
If you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the
Internet, click on the button below.
Internet Connection Setup Wizard
Note:Before launching the wizard, please make sure you have followed all steps outlined in the Quick Installation Guide included in the
package.
MANUAL INTERNET CONNECTION OPTION
If you would like to configure the Internet settings of your new D-Link Router manually, then click on the button below.
D-Link DIR-819 User Manual
Manual Internet Connection Setup
21
Section 3 - Configuration
Web UI Table of Contents
The web-based interface is divided into 5 horizontal tabs, each with a vertical menu bar running along the left side.
You may click on these section titles to quickly navigate to a section of this document.
DIR-819
SETUP
ADVANCED
TOOLS
STATUS
SUPPORT
INTERNET
VIRTUAL SERVER
ADMIN
DEVICE INFO
MENU
WIRELESS SETTINGS
PORT FORWARDING
TIME
LOGS
SETUP
NETWORK SETTINGS
APPLICATION RULES
SYSLOG
STATISTICS
ADVANCED
IPV6
QOS ENGINE
SYSTEM
INTERNET SESSIONS
TOOLS
NETWORK FILTER
FIRMWARE
WIRELESS
STATUS
INBOUND FILTER
DYNAMIC DNS
ROUTING
ACCESS CONTROL
SYSTEM CHECK
IPV6
WEBSITE FILTER
SCHEDULES
IPV6 ROUTING
FIREWALL SETTINGS
ROUTING
ADVANCED WIRELESS
WI-FI PROTECTED SETUP
ADVANCED NETWORK
GUEST ZONE
IPV6 FIREWALL
IPV6 ROUTING
DIR-819
To return to this Web UI Table of Contents page, simply click the D-Link logo on the top
right of each page.
D-Link DIR-819 User Manual
INTERNET
SETUP
INTERNET CONNECTION
22
Section 3 - Configuration
Setup
The Setup tab provides access to configure the basic configuration settings of your DIR-819.
DIR-819
SETUP
ADVANCED
TOOLS
STATUS
SUPPORT
INTERNET
INTERNET CONNECTION
WIRELESS SETTINGS
If you are configuring the device for the first time, we recommend that you click on the Internet Connection Setup Wizard, and follow
the instructions on the screen. If you wish to modify or configure the device settings manually, click the Manual Internet Connection
Setup.
NETWORK SETTINGS
IPV6
INTERNET CONNECTION SETUP WIZARD
If you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the
Internet, click on the button below.
Internet Connection Setup Wizard
Note:Before launching the wizard, please make sure you have followed all steps outlined in the Quick Installation Guide included in the
package.
MANUAL INTERNET CONNECTION OPTION
If you would like to configure the Internet settings of your new D-Link Router manually, then click on the button below.
Manual Internet Connection Setup
DIR-819
To return to the Web UI Table of Contents page, simply click the D-Link logo on the top right
of each page.
D-Link DIR-819 User Manual
INTERNET
SETUP
INTERNET CONNECTION
23
Section 3 - Configuration
Internet
Click Internet on the navigation menu to configure your Internet connection. Using the
Internet Connection Setup Wizard is recommended. To manually configure your Internet
connection, select Manual Internet Connection Setup.
DIR-819
INTERNET CONNECTION SETUP WIZARD
Click Internet Connection Setup Wizard to configure your Internet Connection. Refer to
Internet Connection Setup Wizard on page 25.
INTERNET
SETUP
INTERNET CONNECTION
INTERNET CONNECTION
If you are configuring the device for the first time, we recommend that you click on the Internet Connection Setup Wizard, and follow
the instructions on the screen. If you wish to modify or configure the device settings manually, click the Manual Internet Connection
Setup.
INTERNET CONNECTION SETUP WIZARD
MANUAL INTERNET CONNECTION OPTION
Click Manual Internet Connection Setup to manually add or configure your Internet
connection. Refer to Manual Wireless Connection Setup on page 50.
If you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the
Internet, click on the button below.
Internet Connection Setup Wizard
Note:Before launching the wizard, please make sure you have followed all steps outlined in the Quick Installation Guide included in the
package.
MANUAL INTERNET CONNECTION OPTION
If you would like to configure the Internet settings of your new D-Link Router manually, then click on the button below.
Manual Internet Connection Setup
D-Link DIR-819 User Manual
24
Section 3 - Configuration
Internet Connection Setup Wizard
This Internet Connection Setup Wizard will guide you through a step-by-step process to
configure your new D-Link router and connect to the Internet.
WELCOME TO THE D-LINK INTERNET CONNECTION SETUP WIZARD
This wizard will guide you through a step-by-step process to configure your new D-Link router and connect to the
Internet.
•
•
•
•
Step 1: Set your Password
Step 2: Select your Time Zone
Step 3: Configure your Internet Connection
Step 4: Save Settings and Connect
Prev
STEP 1: SET YOUR PASSWORD
Password :
Verify Password :
Prev
Next
Cancel
Connect
STEP 2: SELECT YOUR TIME ZONE
Select the appropriate time zone for your location. This information is required to configure the time-based options for
the router.
Time Zone :
Prev
Select the connection type your ISP uses and click Next to continue.
Connect
STEP 1: SET YOUR PASSWORD
Select your time zone. Click Next to continue.
STEP 3: CONFIGURE YOUR INTERNET CONNECTION
Cancel
By default, your new D-Link Router does not have a password configured for administrator access to the Web-based
configuration pages. To secure your new networking device, please set and verify a password below:
Enter a new administration password. This is the password you will use to log in to the router.
Click Next to continue.
STEP 2: SELECT YOUR TIME ZONE
Next
(GMT+08:00) Taipei
Next
Cancel
▼
Connect
STEP 3: CONFIGURE YOUR INTERNET CONNECTION
Please select the Internet connection type below:
ž DHCP Connection (Dynamic IP Address)
Choose this if your Internet connection automatically provides you with an IP Address. Most Cable Modems use this type of
connection.
š Username / Password Connection (PPPoE)
For DHCP setup help refer to page 26.
For PPPoE setup help refer to page 27.
For PPTP setup help refer to page 28.
Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type
of connection.
š Username / Password Connection (PPTP)
Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type
of connection.
š Username / Password Connection (L2TP)
Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type
of connection.
š Static IP Address Connection
Choose this option if your Internet Setup Provider provided you with IP Address information that has to be manually configured.
Prev
Next
Cancel
Connect
For L2TP setup help refer to page 30.
For Static IP Address Connection setup help refer to page 32.
D-Link DIR-819 User Manual
25
Section 3 - Configuration
Internet Connection Setup Wizard (continued)
DHCP
If you choose DHCP Connection (Dynamic IP Address) as your Internet Connection, enter your IP address, configure the following settings:
DHCP CONNECTION (DYNAMIC IP ADDRESS)
MAC Address: If your Internet connection is tied to a specific PC or hardware, enter
it manually or click Clone Your PC’s MAC Address.
DHCP CONNECTION (DYNAMIC IP ADDRESS)
To set up this connection, please make sure that you are connected to the D-Link Router with the PC that was originally
connected to your broadband connection. If you are, then click the Clone MAC button to copy your computer’s MAC
Address to the D-Link Router.
MAC Address :
Host Name :
Host Name: Enter the host name of the router.
(optional)
Clone Your PC’s MAC Address
dlinkrouter
Note: You may also need to provide a Host Name.If you do not have or know this information, please contact your ISP.
DNS SETTINGS
Primary DNS Address :
DNS SETTINGS
Secondary DNS Address :
Primary DNS Enter the primary DNS server IP addresses.
Server:
Prev
Next
(optional)
Cancel
Connect
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings.
Prev
Next
Cancel
Connect
26
Section 3 - Configuration
Internet Connection Setup Wizard (continued)
PPPoE
If you choose Username / Password Connection (PPPoE) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPPOE)
SET USERNAME AND PASSWORD CONNECTION (PPPOE)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. If you do
not have this information, please contact your ISP.
Username: Enter the username provided by your ISP.
User Name :
Password :
Password: Enter the password provided by your ISP.
Prev
Next
Cancel
Connect
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings.
Prev
Next
Cancel
Connect
27
Section 3 - Configuration
Internet Connection Setup Wizard (continued)
PPTP
If you choose Username / Password Connection (PPTP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPTP)
SET USERNAME AND PASSWORD CONNECTION (PPTP)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also
need PPTP IP address. If you do not have this information, please contact your ISP.
Address Mode: Select either Dynamic IP or Static IP
Address Mode : ž Dynamic IP š Static IP
PPTP IP Address :
If you choose Static IP as the Address Mode, enter your IP address:
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address :
PPTP IP Address: Enter the PPTP IP Address provided by your ISP.
(may be same as gateway)
User Name :
Password :
PPTP Subnet Enter the PPTP Subnet mask provided by your ISP.
Mask:
Verify Password :
DNS SETTINGS
Primary DNS Address :
PPTP Gateway IP Enter the PPTP Gateway IP Address provided by your ISP.
Address:
Secondary DNS Address :
Prev
Next
(optional)
Cancel
Connect
If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP
address:
PPTP Server IP Enter the PPTP Server IP address provided by your ISP.
Address:
Username: Enter the username provided by your ISP.
Password: Enter the password provided by your ISP.
Verify Password: Enter the password provided by your ISP one more time.
DNS SETTINGS
Primary DNS Enter the primary DNS server IP addresses.
Server:
D-Link DIR-819 User Manual
28
Section 3 - Configuration
Internet Connection Setup Wizard (continued)
PPTP (continued)
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
DNS SETTINGS
Primary DNS Address :
Secondary DNS Address :
Prev
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
Next
(optional)
Cancel
Connect
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings.
Prev
Next
Cancel
Connect
29
Section 3 - Configuration
Internet Connection Setup Wizard (continued)
L2TP
If you choose Username / Password Connection (L2TP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (L2TP)
SET USERNAME AND PASSWORD CONNECTION (L2TP)
To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also
need L2TP IP address. If you do not have this information, please contact your ISP.
Address Mode: Select either Dynamic IP or Static IP
Address Mode : ž Dynamic IP š Static IP
L2TP IP Address :
L2TP Subnet Mask :
If you choose Static IP as the Address Mode, enter your IP address:
L2TP Gateway IP Address :
L2TP Server IP Address :
L2TP IP Address: Enter the PPTP IP Address provided by your ISP.
(may be same as gateway)
User Name :
Password :
L2TP Subnet Enter the PPTP Subnet mask provided by your ISP.
Mask:
Verify Password :
DNS SETTINGS
Primary DNS Address :
Secondary DNS Address :
L2TP Gateway IP Enter the PPTP Gateway IP Address provided by your ISP.
ddress:
Prev
Next
(optional)
Cancel
Connect
If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP
address:
L2TP Server IP Enter the PPTP Server IP address provided by your ISP.
Address:
Username: Enter the username provided by your ISP.
Password: Enter the password provided by your ISP.
Verify Password: Enter the password provided by your ISP one more time.
DNS SETTINGS
Primary DNS Enter the primary DNS server IP addresses.
Server:
D-Link DIR-819 User Manual
30
Section 3 - Configuration
Internet Connection Setup Wizard (continued)
L2TP (continued)
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
DNS SETTINGS
Primary DNS Address :
Secondary DNS Address :
Prev
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
Next
(optional)
Cancel
Connect
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings.
Prev
Next
Cancel
Connect
31
Section 3 - Configuration
Internet Connection Setup Wizard (continued)
Static IP Address Connection
If you choose Static IP Address Connection as your Internet Connection, enter your IP address, configure the following settings:
SET STATIC IP ADDRESS CONNECTION
SET STATIC IP ADDRESS CONNECTION
To set up this connection you will need to have a complete list of IP information provided by your Internet Service
Provider. If you have a Static IP connection and do not have this information, please contact your ISP.
IP Address: Enter the IP address provided by your ISP.
IP Address :
Subnet Mask :
Subnet Mask: Enter the subnet mask.
Default Gateway :
DNS SETTINGS
Default Gateway: Enter the default gateway.
Primary DNS Address :
Secondary DNS Address :
Prev
DNS SETTINGS
Next
(optional)
Cancel
Connect
Primary DNS Enter the primary DNS server IP addresses.
Server:
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings.
Prev
Next
Cancel
Connect
32
Section 3 - Configuration
Manual Internet Connection Setup
Click Manual Internet Setup on from the Internet menu to configure your Internet
connection manually. This section is only recommended for advanced users. It is
recommended to use the Setup Wizard to set up your Internet connection.
DIR-819
INTERNET CONNECTION TYPE
My Internet Select the Internet Connection protocol from the dropdown menu
Connection is: your ISP uses. The options are Static IP, DHCP, PPPoE, PPTP, L2TP,
and DS-Lite.
WAN
INTERNET
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
For Static IP setup help refer to page 34. Select the connection type your ISP uses.
SETUP
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
Static IP
▼
Dynamic IP (DHCP)
For Dynamic IP (DHCP) setup help refer to page 35.
PPPoE (Username / Password)
PPTP (Username / Password)
L2TP (Username / Password)
For PPPoE (Username / Password) setup help refer to page 36.
DS-Lite
For PPTP (Username / Password) setup help refer to page 38.
For L2TP (Username / Password) setup help refer to page 40.
For DS-Lite setup help refer to page 42.
D-Link DIR-819 User Manual
33
Section 3 - Configuration
Static IP
If you choose Static IP, please configure the following fields:
STATIC IP ADDRESS INTERNET CONNECTION TYPE :
IP Address: Enter the IP address provided by your ISP.
DIR-819
SETUP
WAN
INTERNET
Subnet Mask: Enter the subnet mask.
Default Gateway: Enter the default gateway.
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
Primary DNS Enter the primary DNS server IP addresses.
Server:
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
Static IP
▼
STATIC IP ADDRESS INTERNET CONNECTION TYPE :
Enter the static address information provided by your Internet Service Provider (ISP).
IP Address :
Subnet Mask :
MTU Size: Enter the MTU size.
Default Gateway :
Primary DNS Server :
Secondary DNS Server :
MAC Address: If your Internet connection is tied to a specific PC or hardware, enter
it manually or click Clone Your PC’s MAC Address.
MTU :
(optional)
1500
MAC Address :
Clone Your PC’s MAC Address
When you have finished configuring your Internet connection, click the Save Settings
button.
D-Link DIR-819 User Manual
Save Settings
Don’t Save Settings
34
Section 3 - Configuration
Dynamic IP (DHCP)
If you choose Dynamic IP (DHCP), please configure the following fields:
STATIC IP ADDRESS INTERNET CONNECTION TYPE :
Host Name: Enter the host name of the router.
DIR-819
SETUP
WAN
INTERNET
Use Unicasting: Check this box if you are having difficulty obtaining a DHCP address
from your ISP.
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Primary DNS Enter the primary DNS server IP addresses.
Server:
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
Save Settings
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
Dynamic IP (DHCP)
▼
DYNAMIC IP (DHCP) INTERNET CONNECTION TYPE :
Use this Internet connection type if your Internet Service Provider (ISP) didn’t provide you with IP Address information
and/or a username and password.
Host Name :
MTU Size: Enter the MTU size.
Use Unicasting :
dlinkrouter
☐ (compatibility for some DHCP Clients)
Primary DNS Server :
Secondary DNS Server :
MAC Address: If your Internet connection is tied to a specific PC or hardware, enter
it manually or click Clone Your PC’s MAC Address.
MTU :
(optional)
1500
MAC Address :
Clone Your PC’s MAC Address
When you have finished configuring your Internet connection, click the Save Settings
button.
D-Link DIR-819 User Manual
Save Settings
Don’t Save Settings
35
Section 3 - Configuration
PPPoE (Username / Password)
If you choose PPPoE, please configure the following fields:
PPPOE INTERNET CONNECTION TYPE :
Address Mode: Select either Dynamic IP or Static IP
If you choose Static IP as the Address Mode, enter your IP address:
IP Address: Enter the IP address provided by your ISP.
DIR-819
SETUP
WAN
INTERNET
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
Don’t Save Settings
INTERNET CONNECTION TYPE
Username: Enter the username provided by your ISP.
Password: Enter the password provided by your ISP.
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
PPPoE (Username / Password)
▼
PPPOE INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP).
Address Mode : ž Dynamic IP š Static IP
IP Address :
Verify Password: Enter the password provided by your ISP one more time.
User Name :
Password :
Service Name: Enter the ISP service name (optional).
Verify Password :
Service Name :
Reconnect Mode: Select either AlwaysOn, On Demand, or Manual. You may create
a schedule by clicking New Schedule. Refer to Schedules on page
110 for more information.
(optional)
Reconnect Mode : ž
AlwaysOn
▼
New Schedule
š On Demand š Manual
Maximum Idle Time :
(minutes)
DNS Mode : ž Receive DNS from ISP š Enter DNS Manually
Primary DNS Server :
Secondary DNS Server :
If you choose Manual as the Reconnect Mode, enter the Maximum Idle Time:
MTU :
(optional)
1492
MAC Address :
Maximum Idle Set the length of time to wait before disconnecting if there is no
Time: Internet activity. (Manual Only)
Clone Your PC’s MAC Address
Save Settings
Don’t Save Settings
DNS Mode: Select either Receive DNS from ISP or Enter DNS Manually.
If you choose Enter DNS Manually as the DNS Mode, enter your DNS information:
Primary DNS Enter the primary DNS server IP addresses.
Server:
D-Link DIR-819 User Manual
36
Section 3 - Configuration
PPPoE (Username / Password) (Continued)
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
MTU Size: Enter the MTU size.
MAC Address: If your Internet connection is tied to a specific PC or hardware, enter
it manually or click Clone Your PC’s MAC Address.
When you have finished configuring your Internet connection, click the Save Settings
button.
DIR-819
SETUP
WAN
INTERNET
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
PPPoE (Username / Password)
▼
PPPOE INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP).
Address Mode : ž Dynamic IP š Static IP
IP Address :
User Name :
Password :
Verify Password :
Service Name :
(optional)
Reconnect Mode : ž
AlwaysOn
▼
New Schedule
š On Demand š Manual
Maximum Idle Time :
(minutes)
DNS Mode : ž Receive DNS from ISP š Enter DNS Manually
Primary DNS Server :
Secondary DNS Server :
MTU :
(optional)
1492
MAC Address :
Clone Your PC’s MAC Address
Save Settings
D-Link DIR-819 User Manual
Don’t Save Settings
37
Section 3 - Configuration
PPTP (Username / Password)
If you choose PPTP, please configure the following fields:
PPTP INTERNET CONNECTION TYPE :
Address Mode: Select either Dynamic IP or Static IP
DIR-819
SETUP
WAN
INTERNET
If you choose Static IP as the Address Mode, enter your IP address:
PPTP IP Address: Enter the PPTP IP Address provided by your ISP.
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
PPTP Subnet Enter the PPTP Subnet mask provided by your ISP.
Mask:
PPTP Gateway IP Enter the PPTP Gateway IP Address provided by your ISP.
Address:
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
PPTP (Username / Password)
▼
PPTP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP).
Address Mode : ž Dynamic IP š Static IP
PPTP IP Address :
PPTP Subnet Mask :
If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP
address:
PPTP Gateway IP Address :
PPTP Server IP Address :
Username :
Password :
PPTP Server IP Enter the PPTP Server IP address provided by your ISP.
Address:
Verify Password :
Reconnect Mode : ž
AlwaysOn
▼
New Schedule
š On Demand š Manual
Username: Enter the username provided by your ISP.
Maximum Idle Time :
(minutes)
Primary DNS Server :
Secondary DNS Server :
Password: Enter the password provided by your ISP.
MTU :
(optional)
1492
MAC Address :
Verify Password: Enter the password provided by your ISP one more time.
Clone Your PC’s MAC Address
Save Settings
Don’t Save Settings
Reconnect Mode: Select either AlwaysOn, On Demand, or Manual. You may create
a schedule by clicking New Schedule. Refer to Schedules on page
110 for more information.
If you choose Manual as the Reconnect Mode, enter the Maximum Idle Time:
D-Link DIR-819 User Manual
38
Section 3 - Configuration
PPTP (Username / Password) (Continued)
Maximum Idle Set the length of time to wait before disconnecting if there is no
Time: Internet activity. (Manual Only)
Primary DNS Enter the primary DNS server IP addresses.
Server:
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
DIR-819
WAN
INTERNET
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
MTU Size: Enter the MTU size.
SETUP
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
MAC Address: If your Internet connection is tied to a specific PC or hardware, enter
it manually or click Clone Your PC’s MAC Address.
My Internet Connection is :
PPTP (Username / Password)
▼
PPTP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP).
Address Mode : ž Dynamic IP š Static IP
When you have finished configuring your Internet connection, click the Save Settings
button.
PPTP IP Address :
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address :
Username :
Password :
Verify Password :
Reconnect Mode : ž
AlwaysOn
▼
New Schedule
š On Demand š Manual
Maximum Idle Time :
(minutes)
Primary DNS Server :
Secondary DNS Server :
MTU :
(optional)
1492
MAC Address :
Clone Your PC’s MAC Address
Save Settings
D-Link DIR-819 User Manual
Don’t Save Settings
39
Section 3 - Configuration
L2TP (Username / Password)
If you choose L2TP, please configure the following fields:
L2TP INTERNET CONNECTION TYPE :
Address Mode: Select either Dynamic IP or Static IP
DIR-819
SETUP
WAN
INTERNET
If you choose Static IP as the Address Mode, enter your IP address:
L2TP IP Address: Enter the PPTP IP Address provided by your ISP.
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
L2TP Subnet Enter the PPTP Subnet mask provided by your ISP.
Mask:
L2TP Gateway IP Enter the PPTP Gateway IP Address provided by your ISP.
ddress:
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
L2TP (Username / Password)
▼
L2TP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP).
Address Mode : ž Dynamic IP š Static IP
L2TP IP Address :
L2TP Subnet Mask :
If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP
address:
L2TP Gateway IP Address :
L2TP Server IP Address :
Username :
Password :
L2TP Server IP Enter the PPTP Server IP address provided by your ISP.
Address:
Verify Password :
Reconnect Mode : ž
AlwaysOn
▼
New Schedule
š On Demand š Manual
Username: Enter the username provided by your ISP.
Maximum Idle Time :
(minutes)
Primary DNS Server :
Secondary DNS Server :
Password: Enter the password provided by your ISP.
MTU :
(optional)
1492
MAC Address :
Verify Password: Enter the password provided by your ISP one more time.
Clone Your PC’s MAC Address
Save Settings
Don’t Save Settings
Reconnect Mode: Select either AlwaysOn, On Demand, or Manual. You may create
a schedule by clicking New Schedule. Refer to Schedules on page
110 for more information.
If you choose Manual as the Reconnect Mode, enter the Maximum Idle Time:
D-Link DIR-819 User Manual
40
Section 3 - Configuration
L2TP (Username / Password) (continued)
Maximum Idle Set the length of time to wait before disconnecting if there is no
Time: Internet activity. (Manual Only)
Primary DNS Enter the primary DNS server IP addresses.
Server:
Secondary DNS Enter the secondary DNS server IP addresses.
Server :
MTU Size: Enter the MTU size.
DIR-819
SETUP
WAN
INTERNET
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
MAC Address: If your Internet connection is tied to a specific PC or hardware, enter
it manually or click Clone Your PC’s MAC Address.
My Internet Connection is :
L2TP (Username / Password)
▼
L2TP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP).
Address Mode : ž Dynamic IP š Static IP
When you have finished configuring your Internet connection, click
the Save Settings button.
L2TP IP Address :
L2TP Subnet Mask :
L2TP Gateway IP Address :
L2TP Server IP Address :
Username :
Password :
Verify Password :
Reconnect Mode : ž
AlwaysOn
▼
New Schedule
š On Demand š Manual
Maximum Idle Time :
(minutes)
Primary DNS Server :
Secondary DNS Server :
MTU :
(optional)
1492
MAC Address :
Clone Your PC’s MAC Address
Save Settings
D-Link DIR-819 User Manual
Don’t Save Settings
41
Section 3 - Configuration
DS-Lite
If you choose DS-Lite, please configure the following fields:
DS-Lite Mode: Select either DS-Lite DHCPv6 Option or Manual Configuration.
If you choose Manual Configuration, configure the AFTR IPv6 Address field:
AFTR Name or Enter the AFTR Name or Address.
Address:
If you choose DS-Lite DHCPv6 Option or Manual Configuration, configure the B4 IPv6
Address field:
DIR-819
SETUP
WAN
INTERNET
WAN
Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE,
PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider.
Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers.
Save Settings
Don’t Save Settings
INTERNET CONNECTION TYPE
Choose the mode to be used by the router to connect to the Internet.
My Internet Connection is :
B4 IPv6 Address: Enter the B4 IPv6 Address. (optional)
DS-Lite
▼
AFTR ADDRESS INTERNET CONNECTION TYPE :
Enter the AFTR address information provided by your Internet Service Provider (ISP).
DS-Lite Configuration : ž DS-Lite DHCPv6 Option š Manual Configuration
WAN IPv6 Your WAN IPv6 address is listed here.
Address:
AFTR IPv6 Address :
B4 IPv4 Address : 192.0.0.
(optional)
WAN IPv6 Address :
IPv6 WAN Default Gateway :
IPv6 WAN Default Your WAN IPv6 default gateway address is listed here.
Gateway:
Save Settings
Don’t Save Settings
When you have finished configuring your Internet connection, click
the Save Settings button.
D-Link DIR-819 User Manual
42
Section 3 - Configuration
Wireless Settings
Click Wireless Settings on the navigation menu to configure your Wireless Settings. You may
run the Wireless Connection Setup Wizard, Add a Device with WPS, or run the Manual
Wireless Connection Setup.
DIR-819
WIRELESS NETWORK SETUP WIZARD
Click the Wireless Connection Setup Wizard button to easily configure your wireless
settings. Refer to page Wireless Connection Setup Wizard on page 44 for more
information.
WIRELESS SETTINGS
SETUP
WIRELESS SETTINGS
WIRELESS SETTINGS
The following Web-based wizards are designed to assist you in your wireless network setup and wireless device connection.
Before launching these wizards, please make sure you have followed all steps outlined in the Quick Installation Guide included in the
package.
WIRELESS NETWORK SETUP WIZARD
This wizard is designed to assist you in your wireless network setup. It will guide you through step-by-step instructions on how to set up
your wireless network and how to make it secure.
Wireless Connection Setup Wizard
ADD WIRELESS DEVICE WITH WPS (WI-FI PROTECTED SETUP) WIZARD
Click the Add Wireless Device with WPS button (Wi-Fi Protected Setup) to add a device
using WPS Wizard.
Note:Some changes made using this Setup Wizard may require you to change some settings on your wireless client adapters so they
can still connect to the D-Link Router.
ADD WIRELESS DEVICE WITH WPS (WI-FI PROTECTED SETUP) WIZARD
This wizard is designed to assist you in connecting your wireless device to your wireless router. It will guide you through step-by-step
instructions on how to get your wireless device connected. Click the button below to begin.
Add Wireless Device with WPS
MANUAL WIRELESS CONNECTION SETUP
MANUAL WIRELESS CONNECTION SETUP
Click the Manual Wireless Connection Setup button to manually configure your wireless
LAN settings.
D-Link DIR-819 User Manual
If your wireless network is already set up with Wi-Fi Protected Setup, manual configuration of the wireless network will destroy the
existing wireless network. If you would like to configure the wireless settings of your new D-Link Systems Router manually, then click on
the Manual Wireless Network Setup button below.
Manual Wireless Connection Setup
43
Section 3 - Configuration
Wireless Connection Setup Wizard
This section describes the Wireless Connection Setup Wizard.
STEP 1: WELCOME TO THE D-LINK WIRELESS SECURITY SETUP WIZARD
Network Name Enter a name for the 2.4 GHz wireless network.
(SSID) 2.4GHz:
STEP 1: WELCOME TO THE D-LINK WIRELESS SECURITY SETUP WIZARD
Give your network a name, using up to 32 characters.
Network Name (SSID) 2.4GHz :
Network Name (SSID) 5Ghz :
Your_2.4GHz_Network
Your_5GHz_Network
ž Automatically assign a network key (Recommended)
To prevent outsiders from accessing your network, the router will automatically assign a security key (also called WEP or WPA) to
your network.
Network Name Enter a name for the 5 GHz wireless network.
(SSID) 5Ghz:
š Manually assign a network key
Use this options if you prefer to create our own key.
Note: All D-Link wireless adapters currently support WPA.
Prev
Next
Cancel
Save
Automatically Choose this option to have the router automatically create a secure
assign a network: wireless security key.
Manually assign a Choose this option to create your own wireless security key.
network key:
Click Next to continue.
SETUP COMPLETE!
If you choose Automatically assign a network, there is no further configuration. A summary
of your wireless configuration settings is displayed.
Click Save to finish.
SETUP COMPLETE!
Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a
piece of paper, so you can configure the correct settings on your wireless client adapters.
Wireless Band : 2.4GHz Band
Wireless Network Name (SSID) : Your_2.4GHz_Network
Security Mode : Auto (WPA or WPA2) - Personal
Cipher Type: TKIP and AES
Pre-Shared Key : d80a73f50c
Wireless Band : 5GHz Band
Wireless Network Name (SSID) : Your_5GHz_Network
Security Mode : Auto (WPA or WPA2) - Personal
Cipher Type: TKIP and AES
Pre-Shared Key : d80a73f50c
Prev
D-Link DIR-819 User Manual
Next
Cancel
Save
44
Section 3 - Configuration
Wireless Connection Setup Wizard (continued)
If you choose Manually assign a network key, there is no further configuration. A summary of your wireless configuration settings is displayed.
STEP 2: SET YOUR WIRELESS SECURITY PASSWORD
If you checked Use the same Wireless Security Password on both 2.4GHz and 5GHz
band, enter the Wireless Security Password.
STEP 2: SET YOUR WIRELESS SECURITY PASSWORD
You have selected your security level - you will need to set a wireless security password.
The WPA (Wi-Fi Protected Access) key must meet one of following guidelines:
- Between 8 and 63 characters (A longer WPA key is more secure than a short one )
- Exactly 64 characters using 0-9 and A-F
☑ Use the same Wireless Security Password on both 2.4GHz and 5GHz band
Wireless Security Enter a wireless password according to the onscreen guidelines.
Password:
If you unchecked Use the same Wireless Security Password on both 2.4GHz and 5GHz
band, enter a 2.4GhzWireless Security Password and 5GhzWireless Security Password:
Wireless Security Password :
A_Str0ng_P@ssWord!
Note: You will need to enter the same password as keys in this step into your wireless clients in order to enable proper
wireless communication.
Prev
Next
Cancel
Save
STEP 2: SET YOUR WIRELESS SECURITY PASSWORD
You have selected your security level - you will need to set a wireless security password.
2.4GhzWireless Enter a wireless password according to the onscreen guidelines.
Security Password:
5GhzWireless Enter a wireless password according to the onscreen guidelines.
Security Password:
Click Next to continue.
D-Link DIR-819 User Manual
The WPA (Wi-Fi Protected Access) key must meet one of following guidelines:
- Between 8 and 63 characters (A longer WPA key is more secure than a short one )
- Exactly 64 characters using 0-9 and A-F
☐ Use the same Wireless Security Password on both 2.4GHz and 5GHz band
2.4GhzWireless Security Password :
A_Str0ng_P@ssWord!
5GhzWireless Security Password :
A_Str0ng_P@ssWord!
Note: You will need to enter the same password as keys in this step into your wireless clients in order to enable proper
wireless communication.
Prev
Next
Cancel
Save
45
Section 3 - Configuration
Wireless Connection Setup Wizard (continued)
SETUP COMPLETE!
SETUP COMPLETE!
Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a
piece of paper, so you can configure the correct settings on your wireless client adapters.
A summary of your wireless configuration settings is displayed. Click Save to finish.
Wireless Band : 2.4GHz Band
Click Save to finish.
Wireless Network Name (SSID) : Your_2.4GHz_Network
Security Mode : Auto (WPA or WPA2) - Personal
Cipher Type: TKIP and AES
Pre-Shared Key : A_Str0ng_P@ssWord!
Wireless Band : 5GHz Band
Wireless Network Name (SSID) : Your_5GHz_Network
Security Mode : Auto (WPA or WPA2) - Personal
Cipher Type: TKIP and AES
Pre-Shared Key : A_Str0ng_P@ssWord!
Prev
D-Link DIR-819 User Manual
Next
Cancel
Save
46
Section 3 - Configuration
Add Wireless Device with WPS
This section describes the Add Wireless Device with WPS wizard.
STEP 1: SELECT CONFIGURATION METHOD NETWORK
Auto: Choose this option to automatically add a device to your network
using this ‘virtual’ WPS button.
STEP 1: SELECT CONFIGURATION METHOD FOR YOUR WIRELESS NETWORK
Please select one of following configuration methods and click next to continue.
Auto ž Select this option if your wireless device supports WPS (Wi-Fi Protected Setup)
Manual š Select this option will display the current wireless settings for you to configure the wireless device manually
Prev
Next
Cancel
Connect
Manual: Choose this option to see the currently configured wireless networking
settings to enter on your wireless client.
Choose your configuration type and refer to the following pages.
D-Link DIR-819 User Manual
47
Section 3 - Configuration
Add Wireless Device with WPS - Auto
If you choose Auto and click Next, choose the WPS configuration type:
STEP 2: CONNECT YOUR WIRELESS DEVICE
Select the WPS method to use to connect your wireless device, either PIN or PBC. Using
WPS-PIN is not recommended due to security vulnerabilities.
STEP 2: CONNECT YOUR WIRELESS DEVICE
There are two ways to add wireless device to your wireless network:
-PIN (Personal Identification Number)
-PBC (Push Button Configuration)
ž PIN :
please enter the PIN from your wireless device and click the below “Connect” Button within 120 seconds
š PBC :
please press the push button on your wireless device and click the below “Connect” Button within 120 seconds
Prev
PIN: Choose this option and enter the currently configured WPS PIN, refer
to Wi-Fi Protected Setup on page 96 for information on setting
the WPS Pin.
Next
Cancel
Connect
PBC: Choose this option to begin the WPS PBC (Push Button Control)
pairing process.
Click Continue to continue.
STEP 2: CONNECT YOUR WIRELESS DEVICE
Press the WPS button or enter the WPS PIN on the client device which you wish to add to
your DIR-819’s network. The WPS process is only active for 120 seconds.
If your device is successfully added, this screen is displayed. Click Wireless Status to be
directed to the Wireless Status page. Refer to Wireless on page 117 for more information.
If your device could not be found, this screen is displayed. You may click Cancel and retry
running the wizard again.
D-Link DIR-819 User Manual
STEP 2: CONNECT YOUR WIRELESS DEVICE
Please press down the Push Button (physical or virtual) on the wireless device you are adding to your wireless network.
Remain time in second: 120
Adding wireless device: Started
Prev
Next
Cancel
Save
STEP 2: CONNECT YOUR WIRELESS DEVICE
Adding wireless device: Succeeded. To add another device click on the Cancel button below or click on the Wireless Status button to
check wireless status.
Prev
Next
Cancel
Wireless Status
STEP 2: CONNECT YOUR WIRELESS DEVICE
Adding wireless device: Session Time-Out.
Prev
Next
Cancel
Save
48
Section 3 - Configuration
Add Wireless Device with WPS - Manual
If you choose Manual and click Next the currently configured wireless networking settings
to enter on your wireless client are displayed.
Click Wireless Status to be directed to the Wireless Status page. Refer to Wireless on page
117 for more information.
STEP 1: SELECT CONFIGURATION METHOD FOR YOUR WIRELESS NETWORK
Please select one of following configuration methods and click next to continue.
Auto š Select this option if your wireless device supports WPS (Wi-Fi Protected Setup)
Manual ž Select this option will display the current wireless settings for you to configure the wireless device manually
Prev
Next
Cancel
Connect
SETUP COMPLETE!
Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a
piece of paper, so you can configure the correct settings on your wireless client adapters.
2.4 Ghz Frequency
SSID: Your_2.4GHz_Network
Security Mode: WPA2-PSK
Cipher Type: AES
-PIN (Personal Identification Number)
Pre-shared Key:
adc058dce7893caf98ca91
5 Ghz Frequency
SSID: Your_5GHz_Network
Security Mode: None
Prev
D-Link DIR-819 User Manual
Next
Cancel
Wireless Status
49
Section 3 - Configuration
Manual Wireless Connection Setup
Click Manual Wireless Connection Setup from the Wireless Settings menu to configure
your wireless LAN settings. From this page you can configure the wireless security and
network parameters for both the 2.4 GHz and 5 GHz network. When you have finished
configuring your wireless network, click Save Settings.
WIRELESS NETWORK SETTINGS
Wireless Band: 2.4 GHz or 5 GHz
Enable Wireless: Enable or disable this wireless network. From the drop down menu
you may apply a schedule to enable or disable this wireless network.
Click New Schedule to create a new schedule. Refer to Schedules
on page 110 for more information.
DIR-819
SETUP
WIRELESS NETWORK
WIRELESS SETTINGS
WIRELESS NETWORK
Use this section to configure the wireless settings for your D-Link router. Please note that changes made in this section may also need
to be duplicated on your wireless client.
To protect your privacy you can configure wireless security features. Securing your wireless network is important as it is used to protect
the integrity of the information being transmitted. The router is capable of 4 types of wireless security; WEP, WPA only, WPA2 only, and
WPA/WPA2 (auto-detect).
Save Settings
Don’t Save Settings
WIRELESS NETWORK SETTINGS
Wireless Band : 2.4GHz Band
Enable Wireless :
Wireless Network Name :
Wireless Network Create a name for your wireless network.
Name:
802.11 Mode:
☑
Always
New Schedule
▼
Your_2.4GHz_Network
802.11b only
▼
802.11g only
802.11n only
Mixed 802.11g and 802.11b
Mixed 802.11n and 802.11g
802.11 Mode Select the desired wireless networking standards to use. The available
(2.4 GHz): options for the 2.4 GHz wireless network are 802.11b only, 802.11g
only, 802.11n only, Mixed 802.11g and 802.11b, or the default
Mixed 802.11n, 802.11g and 802.11b.
Mixed 802.11n, 802.11g and 802.11b
Enable Auto Channel Scan :
Wireless Channel :
Transmission Rate :
Channel Width :
☑
04
▼
Best (automatic)
▼
20 MHz
(Mbit/s)
▼
20/40 MHz(Auto)
Visibility Status : ž Visible š Invisible
802.11 Mode Select the desired wireless networking standards to use. The available
(5 GHz): options for the 2.4 GHz wireless network are 802.11a only, 802.11n
only, Mixed 802.11a and 802.11n, Mixed 802.11ac and 802.11n,
or the default Mixed 802.11ac, 802.11n and 802.11a.
WIRELESS SECURITY MODE
Security Mode :
None
▼
WEP
WPA-Personal
WPA-Enterprise
Enable Auto Check this box to have the router automatically determine the best
Channel Scan: wireless channel to use.
Wireless Channel: If Auto Scan is disabled, use the dropdown menu to select the wireless
channel to use.
Transmission Rate: Select the desired wireless transmission rate.
D-Link DIR-819 User Manual
50
Section 3 - Configuration
Manual Wireless Connection Setup (continued)
Channel Width Select Auto 20/40 if you are using both 802.11n and non-802.11n
(2.4 GHz): devices, or select 20 MHz if you are not using any 802.11n devices.
WIRELESS NETWORK SETTINGS
Wireless Band : 5GHz Band
Enable Wireless :
Wireless Network Name :
Channel Width Select Auto 20/40/80 if you are using 802.11ac, 802.11n, and 802.11a
(5 GHz): devices. Auto 20/40 select if you are using 802.11n and 802.11a
devices. 20 MHz if you are only using 802.11a devices. Higher channel
width allows for higher speeds.
802.11 Mode:
D-Link DIR-819 User Manual
New Schedule
▼
802.11a only
▼
Mixed 802.11a and 802.11n
Mixed 802.11ac and 802.11n
Mixed 802.11ac, 802.11n and 802.11a
Enable Auto Channel Scan :
Wireless Channel :
Visibility Status: The default setting is Visible. Select Invisible if you do not want to
broadcast the SSID of your wireless network.
Note: Making a network invisible is not a form of security alone.
Refer to Wireless Security Mode on page 52 for more information on configuring your
wireless network’s security.
Always
Your_5GHz_Network
802.11n only
Transmission Rate :
WIRELESS SECURITY MODE
☑
Channel Width :
☑
153
▼
Best (automatic)
▼
20 MHz
(Mbit/s)
▼
20/40 MHz(Auto)
20/40/80 MHz(Auto)
Visibility Status : ž Visible š Invisible
WIRELESS SECURITY MODE
Security Mode :
None
▼
WEP
WPA-Personal
WPA-Enterprise
51
Section 3 - Configuration
Wireless Security Mode
The following pages describe each type of security option. When you have finished configuring your wireless network, click Save Settings.
WIRELESS SECURITY MODE
WIRELESS SECURITY MODE
Security Mode :
None
▼
WEP
Security Option: Select a wireless security encryption option. The options are
None, WEP, WPA-Personal, and WPA-Enterprise. Using WPA is
recommended.
WPA-Personal
WPA-Enterprise
None
WIRELESS SECURITY MODE
WIRELESS SECURITY MODE
Security Mode :
None
▼
Security Mode :
WEP
▼
Security Option: None. Disabling encryption and leaving your wireless network open
is not recommended. Any wireless client will be able to access your
network, be able to use your Internet connection, and leaves you
open to security threats.
WEP
WIRELESS SECURITY MODE
WIRELESS SECURITY MODE
Security Option: WEP. Using WEP encryption is not recommended, as it only offers a
trivial amount of protection for your wireless data. WEP encryption
is only available for use with 802.11b, 802.11g, and 802.11a.
WEP
WEP Key Length: Select the Encryption cipher key bit strength. The available options
are 64 bit (10 hex digits) or 128 bit (26 hex digits).
WEP
WEP Key Length :
Authentication :
64 bit (10 hex digits)
Both
▼
(length applies to all keys)
▼
WEP Key 1 :
Authentication: Select either Both or Shared Key.
WEP Key 1: Enter a wireless key to use on your wireless network.
D-Link DIR-819 User Manual
52
Section 3 - Configuration
WPA-Personal / WPA-Enterprise
WIRELESS SECURITY MODE
WIRELESS SECURITY MODE
Security Mode :
▼
WPA-Enterprise
Security Option: Select either WPA-Personal or WPA-Enterprise. If you are running
a dedicated RADIUS authentication server, choose WPA-Enterprise.
WPA
WPA-Personal
WPA
WPA Mode :
WPA Mode: Select either Auto(WPA or WPA2) or WPA2 Only. WPA2 Only is the
recommended wireless security type. Select Auto (WPA or WPA2)
only if your wireless clients do not support WPA2.
Cipher Type :
Group Key Update Interval :
WPA2 Only
AES
3600
▼
▼
(seconds)
Cipher Type: Select either TKIP and AES, TKIP, or AES. Using AES is the
recommended since TKIP is no longer considered secure.
Group Key Update Enter the group key update interval.
Interval:
If you selected WPA-Personal, enter the Pre-Shared Key:
PRE-SHARED KEY
PRE-SHARED KEY
Pre-Shared Key :
Pre-Shared Key: Enter a wireless key to use on your wireless network.
If you selected WPA-Enterprise, enter your EAP 802.1X Radius server information:
EAP (802.1X)
RADIUS server IP Enter a wireless key to use on your wireless network.
Address:
EAP (802.1X)
RADIUS server IP Address :
RADIUS server Port:
RADIUS server Shared Secret:
RADIUS server Port: Enter your RADIUS server’s port number.
RADIUS server Enter your RADIUS server’s shared secret.
Shared Secret:
D-Link DIR-819 User Manual
53
Section 3 - Configuration
Network Settings
Click Network Settings on the navigation menu to configure your local network settings.
When you are satisfied with your configuration, click Save Settings.
ROUTER SETTINGS
Router IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1.
If you change the IP address, once you click Save Settings, you will
need to enter the new IP address in your browser to get back into
the configuration utility.
Default Subnet Enter the subnet mask of the router. The default subnet mask is
Mask: 255.255.255.0.
DIR-819
SETUP
NETWORK SETTINGS
Use this section to configure the internal network settings of your router and also to configure the built-in DHCP server to assign IP
addresses to computers on your network.The IP address that is configured here is the IP address that you use to access the Webbased management interface.If you change the IP address in this section, you may need to adjust your PC's network settings to access
the network again.
Please note that this section is optional and you do not need to change any of the settings here to get your network up and running.
Save Settings
Don’t Save Settings
ROUTER SETTINGS
Use this section to configure the internal network settings of your router.The IP address that is configured here is the IP address that
you use to access the Web-based management interface.If you change the IP address here, you may need to adjust your PC’s network
settings to access the network again.
Router IP Address:
Host Name: The default address to access the router’s configuration is
http://dlinkrouter.local./ Here, you can replace dlinkrouter with a
name of your choice.
Local Domain Enter the domain name (optional).
Name:
Enable DNS Relay: Disable to transfer the DNS server information from your ISP to your
computers. If enabled, your computers will use the router for a DNS
server.
NETWORK SETTINGS
NETWORK SETTINGS
Default Subnet Mask :
Host Name :
192.168.0.1
255.255.255.0
dlinkrouter
Local Domain Name :
Enable DNS Relay :
(optional)
☑
DHCP SERVER SETTINGS
Use this section to configure the built-in DHCP server to assign IP address to the computers on your network.
Enable DHCP Server :
DHCP IP Address Range :
DHCP Lease Time :
☑
100
to
10080
Always broadcast :
☐
Enable :
☐
200
(addresses within the LAN subnet)
(minutes)
(compatibility for some DHCP Clients)
ADD DHCP RESERVATION
Computer Name :
<<
Computer Name
▼
IP Address :
MAC Address :
DHCP SERVER SETTINGS
Enable DHCP Enable or disable the DHCP server.
Server:
DHCP IP Address Enter the starting and ending IP addresses for the DHCP server’s IP
Range: assignment.
Note: If you statically (manually) assign IP addresses to your computers
or devices, make sure the IP addresses are outside of this range or you
may have an IP conflict.
D-Link DIR-819 User Manual
Clone Your PC’s MAC Address
Add / Update
Clear
DHCP RESERVATIONS LIST
Enable
Host Name
IP Address
NUMBER OF DYNAMIC DHCP CLIENTS
Host Name
Save Settings
IP Address
MAC Address
Expired Time
Don’t Save Settings
54
Section 3 - Configuration
Network Settings (continued)
DHCP Lease Time: The maximum length of time for the IP address lease. Enter the Lease
time in minutes.
DHCP SERVER SETTINGS
Use this section to configure the built-in DHCP server to assign IP address to the computers on your network.
Enable DHCP Server :
DHCP IP Address Range :
DHCP Lease Time :
Always broadcast: Check this box if your clients are having difficulty obtaining an IP
address.
ADD DHCP RESERVATION
☑
100
to
10080
Always broadcast :
☐
Enable :
☐
200
(addresses within the LAN subnet)
(minutes)
(compatibility for some DHCP Clients)
ADD DHCP RESERVATION
Computer Name :
DHCP Reservation allows you to reserve IP addresses for specific machines based on their
unique hardware MAC addresses. During DHCP IP address assignment, these devices will
receive the same IP address. This is particularly useful if you run servers on your network.
<<
Computer Name
▼
IP Address :
MAC Address :
Clone Your PC’s MAC Address
Add / Update
Clear
Enable: Enable or disable DHCP reservation.
Computer Name: Enter a name for your DHCP reservation rule. To easily add an IP
reservation for an existing device select it from the drop down menu
and click the << button. The fields will automatically populate.
IP Address: Enter the IP address you wish to have assigned to this device.
MAC Address: Enter the MAC address of the device you wish to apply the DHCP
reservation rule to. Click Clone Your PC’s MAC Address to fill this field.
Click Add / Update when you are done.
DHCP RESERVATIONS LIST
DHCP RESERVATIONS LIST
Enable
Host Name
IP Address
The currently defined DHCP Reservations are listed here.
Enable: Enable or disable this DHCP Reservation rule.
Host Name: The host name for this rule.
IP Address: The DHCP IP address reservation.
D-Link DIR-819 User Manual
55
Section 3 - Configuration
Network Settings (continued)
MAC Address: The MAC address of the device.
DHCP RESERVATIONS LIST
Enable
Host Name
IP Address
Edit Button: Click this button to edit this rules settings.
Delete Button: Click this button to delete this DHCP IP Reservation.
NUMBER OF DYNAMIC DHCP CLIENTS
This section displays all of the currently connected DHCP cclients. The Host Name, IP address,
MAC Address, and expiration time of each client is displayed in the table.
NUMBER OF DYNAMIC DHCP CLIENTS
Host Name
Save Settings
IP Address
MAC Address
Expired Time
Don’t Save Settings
Click Save Settings when you are finished.
D-Link DIR-819 User Manual
56
Section 3 - Configuration
IPv6
Click IPv6 on the navigation menu to configure IPv6 connectivity.
The IPv6 Internet Connection Setup Wizard allows you to quickly set up an IPv6 Internet
connection which uses PPPoE, Static IP, or 6rd. See IPv6 Internet Connection Setup
Wizard on page 58 for more information.
To configure your router to use IPv6 locally on your LAN only see IPv6 Local Connectivity
Settings on page 62.
You may also manually configure your IPv6 connection. See Manual IPv6 Internet
Connection Setup on page 63.
DIR-819
SETUP
IPV6 INTERNET CONNECTION
IPV6
IPV6 INTERNET CONNECTION
There are two ways to set up your IPv6 Internet connection. You can use the Web-based IPv6 Internet Connection Setup Wizard, or
you can manually configure the connection.
IPV6 INTERNET CONNECTION SETUP WIZARD
If you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the IPv6
Internet, click on the button below.
IPv6 Internet Connection Setup Wizard
Note:Before launching the wizards, please make sure you have followed all steps outlined in the Quick Installation Guide included in
the package.
MANUAL IPV6 LOCAL CONNECTIVITY SETUP
If you would like to configure the IPv6 local connectivity settings of your D-Link Router, then click on the button below.
IPv6 Local Connectivity Settings
MANUAL IPV6 INTERNET CONNECTION SETUP
If you would like to configure the IPv6 Internet settings of your new D-Link Router manually, then click on the button below.
Manual IPv6 Internet Connection Setup
D-Link DIR-819 User Manual
57
Section 3 - Configuration
IPv6 Internet Connection Setup Wizard
The IPv6 Internet Connection Setup Wizard allows you to quickly set up an IPv6 Internet
connection which uses PPPoE, Static IP, or 6rd. Click Next to begin.
WELCOME TO THE D-LINK IPV6 INTERNET CONNECTION SETUP WIZARD
This wizard will guide you through a step-by-step process to configure your new D-Link router and connect to the IPv6
Internet.
• Step 1: Configure your IPv6 Internet Connection
• Step 2: Save Settings and Connectnect
STEP 1: CONFIGURE YOUR IPV6 INTERNET CONNECTION
Choose your IPv6 connection type and click Next.
Prev
Next
Cancel
Connect
STEP 1: CONFIGURE YOUR IPV6 INTERNET CONNECTION
Please select your IPv6 Internet Connection type:
ž
For IPv6 over PPPoE setup help refer to page 59.
IPv6 over PPPoE
Choose this option if your IPv6 Internet connection requires a username and password to get online. Most DSL modems use this
type of connection.
š
Static IPv6 address and Route
Choose this option if your Internet Setup Provider (ISP) provided you with IPv6 Address information that has to be manually
configured.
For Static IPv6 address and Route setup help refer to page 60.
For Tunneling Connection (6rd) setup help refer to page 61.
D-Link DIR-819 User Manual
š
Tunneling Connection (6rd)
Choose this option if your Internet Setup Provider (ISP) provided you a IPv6 Internet Connection by using 6rd automatic tunneling
mechanism.
Prev
Next
Cancel
Connect
58
Section 3 - Configuration
IPv6 Internet Connection Setup Wizard
IPv6 over PPPoE
If you choose IPv6 over PPPoE as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPPOE)
SET USERNAME AND PASSWORD CONNECTION (PPPOE)
To set up this connection you will need to have a Username and Password from your IPv6 Internet Service Provider. If
you do not have this information, please contact your ISP.
PPPoE Session : Select whethe to Share with IPv4 or Create a new session.
PPPoE Session : ž Share with IPv4 š Create a new session
User Name :
Password :
If you choose Create a new session as the PPPoE Session, fill in the following fields:
Verify Password :
Service Name :
Username: Enter the username provided by your ISP.
(optional)
Note: You may also need to provide a Service Name. If you do not have or know this information, please contact your ISP.
Prev
Next
Cancel
Connect
Password: Enter the password provided by your ISP.
Verify Password: Enter the password provided by your ISP one more time.
Service Name: Enter the ISP service name (optional).
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
SETUP COMPLETE!
The IPv6 Internet Connection Setup Wizard has completed. Click the Connect button to save your settings and reboot
the router.
Prev
Next
Cancel
Connect
59
Section 3 - Configuration
IPv6 Internet Connection Setup Wizard
Static IPv6 address and Route
If you choose Static IPv6 address and Route as your Internet Connection, enter your IP address, configure the following settings:
SET STATIC IPV6 ADDRESS CONNECTION
SET STATIC IPV6 ADDRESS CONNECTION
To set up this connection you will need to have a complete list of IPv6 information provided by your IPv6 Internet
Service Provider. If you have a Static IPv6 connection and do not have this information, please contact your ISP.
Use Link-Local Enable or disable using the Link-Local Address. The IPv6 Address and
Address: Subnet Prefix Length is automatically populated with this function.
Use Link-Local Address :
☑
IPv6 Address :
Subnet Prefix Length :
Default Gateway :
IPv6 Address: Enter the address supplied by your ISP.
Primary IPv6 DNS Address :
Secondary IPv6 DNS Address :
Subnet Prefix Enter the subnet prefix length supplied by your ISP.
Length:
LAN IPv6 Address :
Prev
Next
Cancel
Connect
Default Gateway: Enter the default gateway for your IPv6 connection.
Primary IPv6 DNS Enter the primary DNS server address.
Address:
Secondary IPv6 Enter the secondary DNS server address.
DNS Address:
LAN IPv6 Address: Enter your the LAN IPv6 Address you want to use.
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
SETUP COMPLETE!
The IPv6 Internet Connection Setup Wizard has completed. Click the Connect button to save your settings and reboot
the router.
Prev
Next
Cancel
Connect
60
Section 3 - Configuration
IPv6 Internet Connection Setup Wizard
Tunneling Connection (6rd)
If you choose Tunneling Connection (6rd) as your Internet Connection, enter your IP address, configure the following settings:
SET UP 6RD TUNNELING CONNECTION
SET UP 6RD TUNNELING CONNECTION
To set up this 6rd tunneling connection you will need to have the following information from your IPv6 Internet Service
Provider. If you do not have this information, please contact your ISP.
6rd IPv6 Prefix: Enter the 6rd IPv6 prefix and mask length supplied by your ISP.
6rd IPv6 Prefix :
IPv4 Address :
Mask Length :
Assigned IPv6 Prefix :
IPv4 Address: Displays the router’s IPv4 address and mask length.
6rd Border Relay IPv4 Address :
Primary IPv6 DNS Address :
Assigned IPv6 Displays the router’s assigned IPv6 prefix.
Prefix:
Prev
Next
Cancel
Connect
6rd Border Relay Enter the 6rd border relay IPv4 address settings supplied by your ISP.
IPv4 Address:
IPv6 DNS Server: Enter the IPv6 DNS server address.
Click Next to continue.
SETUP COMPLETE!
Click Connect to finish the setup.
D-Link DIR-819 User Manual
SETUP COMPLETE!
The IPv6 Internet Connection Setup Wizard has completed. Click the Connect button to save your settings and reboot
the router.
Prev
Next
Cancel
Connect
61
Section 3 - Configuration
IPv6 Local Connectivity Settings
Click the IPv6 Local Connectivity Settings button to configure IPv6 on your local network.
When you are satisfied with your configuration, click Save Settings.
IPV6 ULA SETTINGS
Enable ULA: Enable or disable ULA.
Use default ULA Enable or disable the use of the default ULA prefix.
prefix:
If you enabled ULA, enter your ULA prefix:
DIR-819
SETUP
IPV6 LOCAL CONNECTIVITY SETTINGS
IPV6
IPV6 LOCAL CONNECTIVITY SETTINGS
Use this section to configure Unique Local IPv6 Unicast Address (ULA) settings for your router.ULA is intended for local communications
and not expected to be routable on the global Internet.
Save Settings
Don’t Save Settings
IPV6 ULA SETTINGS
Enable ULA :
Use default ULA prefix :
ULA Prefix: Enter your ULA prefix.
☑
☑
Use default ULA prefix :
/64
CURRENT IPV6 ULA SETTINGS
Current ULA Prefix : /64
LAN IPv6 ULA : /64
IPV6 ULA SETTINGS
Save Settings
Don’t Save Settings
Current ULA The current ULA Prefix is displayed here.
Prefix:
LAN IPv6 ULA: The current LAN IPv6 ULA is displayed here.
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
62
Section 3 - Configuration
Manual IPv6 Internet Connection Setup
Click the Manual IPv6 Internet Connection Setup button to manually configure your IPv6
connection to your ISP. When you are satisfied with your configuration, click Save Settings.
IPV6 INTERNET CONNECTION SETUP WIZARD
My IPv6 Choose your IPv6 connection type from the drop-down menu. You will
Connection is: be presented with the appropriate options for your connection type.
DIR-819
SETUP
IPV6
IPV6
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
For Static IPv6 refer to page 64.
Save Settings
Don’t Save Settings
IPV6 CONNECTION TYPE
For Autoconfiguration(SLAAC/DHCPv6) refer to page 66.
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
Static IPv6
▼
Autoconfiguration(SLAAC/DHCPv6)
PPPoE
For PPPoE refer to page 68.
IPv6 in IPv4 Tunnel
6to4
6rd
Local Connectivity Only
For IPv6 in an IPv4 Tunnel refer to page 71.
For 6to4 refer to page 74.
For 6rd refer to page 76.
For Local Connectivity Only refer to page 78.
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
63
Section 3 - Configuration
Static IPv6
IPV6 CONNECTION TYPE
My IPv6 Select Static IPv6 if your IPv6 information is provided by your ISP.
Connection is:
DIR-819
SETUP
IPV6
IPV6
WAN IPV6 ADDRESS SETTINGS
Use Link-Local Enable or disable using the Link-Local Address. The IPv6 Address and
Address: Subnet Prefix Length is automatically populated with this function.
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
Save Settings
Don’t Save Settings
IPV6 CONNECTION TYPE
IPv6 Address: Enter the address supplied by your ISP.
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
Static IPv6
▼
WAN IPV6 ADDRESS SETTINGS
Subnet Prefix Enter the subnet prefix length supplied by your ISP.
Length:
Enter the IPv6 address information provided by your Internet Service Provider (ISP).
Use Link-Local Address :
☑
IPv6 Address :
Subnet Prefix Length :
Default Gateway: Enter the default gateway for your IPv6 connection.
Primary DNS Enter the primary DNS server address.
Address:
Default Gateway :
Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
LAN IPv6 Address :
Secondary DNS Enter the secondary DNS server address.
Address:
/64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
LAN IPv6 Address Settings
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
Stateful DHCPv6
Router Advertisement Lifetime :
Save Settings
(minutes)
Don’t Save Settings
LAN IPv6 Link- Displays the router’s LAN link-local address.
Local Address:
D-Link DIR-819 User Manual
64
Section 3 - Configuration
Static IPv6 (continued)
Address Autoconfiguration Settings
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. If
IPv6 address you disable this option, no further configuration is available.
assignment:
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
▼
Stateful DHCPv6
Router Advertisement LIfetime :
(minutes)
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
If you choose SLAAC+Stateless DHCP, please configure the following field:
Router Enter the IPv6 address lifetime (in minutes).
Advertisement
Lifetime:
SLAAC+RDNSS
SLAAC+Stateless DHCP
Save Settings
Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6.
Type:
☑
Autoconfiguration Type :
Stateful DHCPv6
▼
IPv6 Address Range (Start) :
:00
IPv6 Address Range (End) :
:00
ff
Router Advertisement LIfetime :
Save Settings
☑
(minutes)
Don’t Save Settings
If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Range(Start):
IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Range(End):
Router Enter the IPv6 address lifetime (in seconds).
Advertisement
Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
65
Section 3 - Configuration
Autoconfiguration(SLAAC/DHCPv6)
IPV6 CONNECTION TYPE
My IPv6 Select Autoconfiguration(SLAAC/DHCPv6) if your ISP assigns your
Connection is: IPv6 address when your router requests one from the ISP’s server.
Some ISPs require you to adjust settings on your side before your
router can connect to the IPv6 Internet.
DIR-819
SETUP
IPV6
IPV6
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
IPV6 DNS SETTINGS
Select either Obtain DNS server address automatically or Use the following DNS address.
Save Settings
Don’t Save Settings
IPV6 CONNECTION TYPE
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
If you choose Use the following DNS address, please configure the following field:
Autoconfiguration(SLAAC/DHCPv6)
▼
IPV6 DNS SETTINGS
Obtain DNS server address automatically or enter a specific DNS server address.
ž Obtain IPv6 DNS Servers automatically
Primary DNS Enter the primary DNS server address.
Address:
Secondary DNS Enter the secondary DNS server address.
Address:
š Use the following IPv6 DNS Servers
Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
Enable DHCP-PD :
☑
LAN IPv6 Address :
/64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
LAN IPv6 Address Settings
Enable DHCP-PD: Check this box to enable DHCP-PD.
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
D-Link DIR-819 User Manual
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Router Advertisement Lifetime :
LAN IPv6 Link- Displays the router’s LAN link-local address.
Local Address:
☑
☑
Save Settings
(minutes)
Don’t Save Settings
66
Section 3 - Configuration
Autoconfiguration(SLAAC/DHCPv6) (continued)
Address Autoconfiguration Settings
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. If
IPv6 address you disable this option, no further configuration is available.
assignment:
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
SLAAC+RDNSS
Stateful DHCPv6
Router Advertisement Lifetime :
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature
DHCP-PD in LAN: for the LAN.
▼
SLAAC+Stateless DHCP
Save Settings
(minutes)
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6.
Type:
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
If you choose SLAAC+Stateless DHCP, the following field appears:
Router The currently defined router advertisement lifetime is displayed.
Advertisement
Lifetime:
Stateful DHCPv6
▼
IPv6 Address Range (Start) :
:00
IPv6 Address Range (End) :
:00
ff
Router Advertisement Lifetime :
Save Settings
☑
☑
(minutes)
Don’t Save Settings
If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Range(Start):
IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Range(End):
Router The currently defined router advertisement lifetime is displayed.
Advertisement
Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
67
Section 3 - Configuration
PPPoE
IPV6 CONNECTION TYPE
My IPv6 Select PPPoE if your ISP provides and requires you to enter a PPPoE
Connection is: username and password in order to connect to the Internet.
DIR-819
SETUP
IPV6
IPV6
PPPOE INTERNET CONNECTION TYPE :
PPPoE Session : Select whethe to Share with IPv4 or Create a new session.
Address Mode: Select either Dynamic IP or Static IP.
If you chose Share with IPv4 as the PPPoE Session with Static IP as the Address Mode,
enter your IP address:
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
Save Settings
Don’t Save Settings
IPV6 CONNECTION TYPE
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
PPPoE
▼
PPPOE INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP).
PPPoE Session : ž Share with IPv4 š Create a new session
Address Mode : ž Dynamic IP š Static IP
IP Address: Enter the IP address provided by your ISP.
IP Address :
User Name :
If you choose Create a new session as the PPPoE Session, fill in the following fields:
Password :
Verify Password :
Service Name :
Username: Enter the username provided by your ISP.
(optional)
Reconnect Mode : ž Always on š On Demand š Manual
Maximum Idle Time :
Password: Enter the password provided by your ISP.
(minutes, 0=infinite)
MTU :
1492
(byes) MTU default=1492
IPV6 DNS SETTINGS
Verify Password: Enter the password provided by your ISP one more time.
Obtain DNS server address automatically or enter a specific DNS server address.
ž Obtain IPv6 DNS Servers automatically
š Use the following IPv6 DNS Servers
Service Name: Enter the ISP service name (optional).
Reconnect Mode: Select either AlwaysOn or Manual.
Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
Enable DHCP-PD :
Maximum Idle Set the length of time to wait before disconnecting if there is no
Time: Internet activity. (Manual Only)
MTU Size: Enter the MTU size.
☑
LAN IPv6 Address :
/64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Router Advertisement Lifetime :
D-Link DIR-819 User Manual
(minutes)
68
Section 3 - Configuration
PPPoE (continued)
IPV6 DNS SETTINGS
IPV6 DNS SETTINGS
Obtain DNS server address automatically or enter a specific DNS server address.
ž Obtain IPv6 DNS Servers automatically
Select either Obtain DNS server address automatically or Use the following DNS address.
š Use the following IPv6 DNS Servers
Primary DNS Address :
If you choose Use the following DNS address, please configure the following field:
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS
Primary DNS Enter the primary DNS server address.
Address:
Secondary DNS Enter the secondary DNS server address.
Address:
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
Enable DHCP-PD :
/64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
LAN IPv6 Address Settings
If you chose Dynamic IP as the Address Mode, you have the option to enable DHCP-PD
appears:
☑
LAN IPv6 Address :
Stateful DHCPv6
Router Advertisement Lifetime :
Save Settings
(minutes)
Don’t Save Settings
Enable DHCP-PD: Check this box to enable DHCP-PD.
If you chose Static IP as the Address Mode, or disabled DHCP-PD, enter your LAN IPv6
Address:
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
LAN IPv6 Link- Displays the router’s LAN link-local address.
Local Address:
D-Link DIR-819 User Manual
69
Section 3 - Configuration
PPPoE (continued)
Address Autoconfiguration Settings
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. If
IPv6 address you disable this option, no further configuration is available.
assignment:
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature
DHCP-PD in LAN: for the LAN.
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Router Advertisement LIfetime :
Save Settings
If you chose Dynamic IP as the Address Mode and enabled DHCP-PD in LAN IPv6 Address
Settings, you may enable DHCP-PD for the LAN:
☑
(minutes)
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6.
Type:
If you choose SLAAC+Stateless DHCP, the following field appears:
Router Advertisement Lifetime :
Save Settings
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Router The currently defined router advertisement lifetime is displayed.
Advertisement
Lifetime:
(minutes)
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
Stateful DHCPv6
:00
IPv6 Address Range (End) :
:00
ff
Router Advertisement Lifetime :
If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Range(Start):
Save Settings
▼
IPv6 Address Range (Start) :
(minutes)
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Range(End):
Stateful DHCPv6
▼
IPv6 Address Range (Start) :
:00
IPv6 Address Range (End) :
:00
ff
Router Advertisement LIfetime :
Save Settings
☑
(minutes)
Don’t Save Settings
Router The currently defined router advertisement lifetime is displayed.
Advertisement
Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
70
Section 3 - Configuration
IPv6 in an IPv4 Tunnel
IPV6 CONNECTION TYPE
My IPv6 Select IPv6 In IPv4 Tunnel if you wish to configure the IPv6 connection
Connection is: to run in IPv4 Tunnel mode. IPv6 over IPv4 tunnelling encapsulates
IPv6 packets in IPv4 packets so that IPv6 packets can be sent over an
IPv4 infrastructure.
DIR-819
SETUP
IPV6
IPV6
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
IPv6 in IPv4 Tunnel Settings
Remote IPv4 Enter the IPv4 remote address.
Address:
Save Settings
Don’t Save Settings
IPV6 CONNECTION TYPE
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
IPv6 in IPv4 Tunnel
▼
IPV6 IN IPV4 TUNNEL SETTINGS
Remote IPv6 Enter the IPv6 remote address.
Address:
Enter the information provided by your Internet Service Provider (ISP).
Remote IPv4 Address :
Remote IPv6 Address :
Local IPv4 Address :
Local IPv4 Displays the current local IPv4 address.
Address:
Local IPv6 Enter the IPv6 local address.
Address:
Local IPv6 Address :
Subnet Prefix Length :
IPV6 DNS SETTINGS
Obtain DNS server address automatically or enter a specific DNS server address.
ž Obtain IPv6 DNS Servers automatically
š Use the following IPv6 DNS Servers
Primary DNS Address :
Secondary DNS Address :
Subnet Prefix Enter the IPv6 subnet prefix length.
Length:
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
Enable DHCP-PD :
☑
LAN IPv6 Address :
/64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Router Advertisement Lifetime :
D-Link DIR-819 User Manual
(minutes)
71
Section 3 - Configuration
IPv6 in and IPv4 Tunnel (continued)
IPV6 DNS SETTINGS
IPV6 DNS SETTINGS
Obtain DNS server address automatically or enter a specific DNS server address.
ž Obtain IPv6 DNS Servers automatically
Select either Obtain DNS server address automatically or Use the following DNS address.
š Use the following IPv6 DNS Servers
Primary DNS Address :
If you choose Use the following DNS address, please configure the following field:
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS
Primary DNS Enter the primary DNS server address.
Address:
Secondary DNS Enter the secondary DNS server address.
Address:
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
Enable DHCP-PD :
/64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
LAN IPv6 Address Settings
Enable DHCP-PD: Check this box to enable DHCP-PD.
☑
LAN IPv6 Address :
Stateful DHCPv6
Router Advertisement Lifetime :
Save Settings
(minutes)
Don’t Save Settings
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. Not available if
DHCP-PD is enabled.
LAN IPv6 Link- Displays the router’s LAN link-local address.
Local Address:
D-Link DIR-819 User Manual
72
Section 3 - Configuration
IPv6 in an IPv4 Tunnel (continued)
Address Autoconfiguration Settings
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. If
IPv6 address you disable this option, no further configuration is available.
assignment:
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature
DHCP-PD in LAN: for the LAN.
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Router Advertisement LIfetime :
Save Settings
If you enabled DHCP-PD in LAN IPv6 Address Settings, you may enable DHCP-PD for the
LAN:
☑
(minutes)
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6.
Type:
If you choose SLAAC+Stateless DHCP, the following field appears:
Router Advertisement Lifetime :
Save Settings
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD
to delegate prefixes for routers in your LAN.
Enable Automatic IPv6 address assignment :
Router The currently defined router advertisement lifetime is displayed.
Advertisement
Lifetime:
(minutes)
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
☑
☑
Stateful DHCPv6
:00
IPv6 Address Range (End) :
:00
ff
Router Advertisement Lifetime :
If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Range(Start):
Save Settings
▼
IPv6 Address Range (Start) :
(minutes)
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Range(End):
Stateful DHCPv6
▼
IPv6 Address Range (Start) :
:00
IPv6 Address Range (End) :
:00
ff
Router Advertisement LIfetime :
Save Settings
☑
(minutes)
Don’t Save Settings
Router The currently defined router advertisement lifetime is displayed.
Advertisement
Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
73
Section 3 - Configuration
6to4
IPV6 CONNECTION TYPE
My IPv6 Select IPv6 In IPv4 Tunnel if you wish to configure your router to
Connection is: connect to your ISP using 6 to 4. 6 to 4 is an IPv6 address assignment
and automatic tunneling technology that is used to provide unicast
IPv6 connectivity between IPv6 sites and hosts across the IPv4
Internet.
DIR-819
SETUP
IPV6
IPV6
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
Save Settings
WAN IPV6 ADDRESS SETTINGS
6to4 Address: The current 6to4 address is displayed here.
Don’t Save Settings
IPV6 CONNECTION TYPE
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
6to4
▼
WAN IPV6 ADDRESS SETTINGS
6to4 Relay: Enter the 6 to 4 relay address supplied by your ISP.
Enter the IPv6 address information provided by your Internet Service Provider (ISP).
6to4 Address :
6to4 relay :
Primary DNS Enter the primary DNS server address.
Address:
Secondary DNS Enter the secondary DNS server address.
Address:
Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
LAN IPv6 Address : XXXX:XXXX:XXXX:
::1 /64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
LAN IPv6 Address Settings
Autoconfiguration Type :
D-Link DIR-819 User Manual
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
LAN IPv6 Link- Displays the router’s LAN link-local address.
Local Address:
☑
Router Advertisement Lifetime :
Save Settings
(minutes)
Don’t Save Settings
74
Section 3 - Configuration
6to4 (continued)
Address Autoconfiguration Settings
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. If
IPv6 address you disable this option, no further configuration is available.
assignment:
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
▼
Stateful DHCPv6
Router Advertisement LIfetime :
(minutes)
Don’t Save Settings
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
If you choose SLAAC+Stateless DHCP, please configure the following field:
Router Enter the IPv6 address lifetime (in minutes).
Advertisement
Lifetime:
SLAAC+RDNSS
SLAAC+Stateless DHCP
Save Settings
Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6.
Type:
☑
Autoconfiguration Type :
Stateful DHCPv6
▼
IPv6 Address Range (Start) :
:00
IPv6 Address Range (End) :
:00
ff
Router Advertisement LIfetime :
Save Settings
☑
(minutes)
Don’t Save Settings
If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Range(Start):
IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Range(End):
Router Enter the IPv6 address lifetime (in seconds).
Advertisement
Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
75
Section 3 - Configuration
6rd
IPV6 CONNECTION TYPE
My IPv6 Select 6rd if your ISP uses the 6rd IPv6 connection protocol.
Connection is:
DIR-819
SETUP
IPV6
IPV6
WAN IPV6 ADDRESS SETTINGS
6rd Configuration: Select either 6rd DHCPv4 or Manual Configuration.
If you selected Manual Configuration, fill in the following fields:
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
Save Settings
Don’t Save Settings
IPV6 CONNECTION TYPE
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
6rd IPv6 Prefix: Enter the 6rd IPv6 prefix and mask length supplied by your ISP.
6rd
▼
WAN IPV6 ADDRESS SETTINGS
Enter the IPv6 address information provided by your Internet Service Provider (ISP).
6rd Configuration : ž 6rd DHCPv4 option š Manual Configuration
IPv4 Address: Displays the router’s IPv4 address and mask length.
6rd IPv6 Prefix :
IPv4 Address :
Assigned IPv6 Displays the router’s assigned IPv6 prefix.
Prefix:
Mask Length :
Assigned IPv6 Prefix :
Tunnel Link-Local Address :
6rd Border Relay IPv4 Address :
Primary DNS Address :
Tunnel Link-Local Displays the tunnel link-local address.
Address:
6rd Border Relay Enter the 6rd border relay IPv4 address settings supplied by your ISP.
IPv4 Address:
Primary DNS Enter the primary DNS server address.
Address:
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
LAN IPv6 Address : XXXX:XXXX:XXXX:
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Router Advertisement Lifetime :
Secondary DNS Enter the secondary DNS server address.
Address:
::1 /64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
Save Settings
(minutes)
Don’t Save Settings
LAN IPV6 ADDRESS SETTINGS
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
D-Link DIR-819 User Manual
76
Section 3 - Configuration
6rd (continued)
LAN IPv6 Link- Displays the router’s LAN link-local address.
Local Address:
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to
adjust your PC network settings to access the network again.
LAN IPv6 Address : XXXX:XXXX:XXXX:
::1 /64
LAN IPv6 Link-Local Address : ffff::fff:ffff:ffff:1234 /64
Address Autoconfiguration Settings
Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. If
IPv6 address you disable this option, no further configuration is available.
assignment:
ADDRESS AUTOCONFIGURATION SETTINGS
Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network.
Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
☑
SLAAC+RDNSS
▼
SLAAC+Stateless DHCP
Stateful DHCPv6
Router Advertisement Lifetime :
Save Settings
(minutes)
Don’t Save Settings
Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6.
Type:
If you choose SLAAC+Stateless DHCP, please configure the following field:
Router Enter the IPv6 address lifetime (in minutes).
Advertisement
Lifetime:
If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Range(Start):
IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Range(End):
Router Enter the IPv6 address lifetime (in seconds).
Advertisement
Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button.
D-Link DIR-819 User Manual
77
Section 3 - Configuration
Local Connectivity Only
IPV6 CONNECTION TYPE
My IPv6 Select Local Connectivity Only allows you to set up a local IPv6
Connection is: connection that does not connect to the Internet.
DIR-819
SETUP
IPV6
IPV6
IPV6 CONNECTION TYPE
LAN IPv6 Link- Displays the router’s LAN IPv6 Link-Local address and mask length.
Local Address :
IPV6
Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet
Service Provider.
Save Settings
Don’t Save Settings
IPV6 CONNECTION TYPE
LAN IPv6 Unique Displays the router’s LAN IPv6 unique local address and mask length.
Local Address :
Choose the mode to be used by the router to connect to the IPv6 Internet.
My IPv6 Connection is:
Local Connectivity Only
▼
LAN IPV6 ADDRESS SETTINGS
Use this section to configure the internal network settings of your router.
LAN IPv6 Link-Local Address : XXXX:XXXX:XXXX:XXXX / 64
When you have finished configuring your IPv6 connection, click the Save Settings button.
LAN IPv6 Unique Local Address : ffff::fff:ffff:ffff:1234 /64
Save Settings
D-Link DIR-819 User Manual
Don’t Save Settings
78
Section 3 - Configuration
Advanced
The Advanced tab provides access to configure the advanced features of your DIR-819.
DIR-819
SETUP
ADVANCED
TOOLS
STATUS
SUPPORT
VIRTUAL SERVER
VIRTUAL SERVER
PORT FORWARDING
The Virtual Server option allows you to define a single public port on your router for redirection to an internal LAN IP Address and
Private LAN port if required.This feature is useful for hosting online services such as FTP or Web Servers.
APPLICATION RULES
Save Settings
Don’t Save Settings
QOS ENGINE
NETWORK FILTER
24 - VIRTUAL SERVERS LIST
Remaining number of rules that can be created: 24
INBOUND FILTER
Port
Name
ACCESS CONTROL
WEBSITE FILTER
☐
<<
Application Name
▼
<<
Computer Name
▼
IP Address
FIREWALL SETTINGS
Traffic Type
Public Port
Protocol
TCP
▼
Schedule
Always
▼
Inbound Filter
Private Port
Allow All
▼
ROUTING
ADVANCED WIRELESS
Save Settings
Don’t Save Settings
WI-FI PROTECTED SETUP
ADVANCED NETWORK
GUEST ZONE
IPV6 FIREWALL
IPV6 ROUTING
DIR-819
To return to the Web UI Table of Contents page, simply click the D-Link logo on the top right
of each page.
D-Link DIR-819 User Manual
INTERNET
SETUP
INTERNET CONNECTION
79
Section 3 - Configuration
Virtual Server
Click Virtual Server on the navigation menu to configure the virtual server. The virtual
server performs port-redirection, which allows remote users to access multiple services
on your local network via your public IP address. For example, you may want to connect
two FTP servers on two different machines on your local network to the Internet. Using
Port Forwarding only allows a single machine use port 21, but with port forwarding you
can remap two different external ports to each machine. When you are satisfied with your
configuration, click Save Settings.
24 - VIRTUAL SERVERS LIST
Enable: Check the box to enable this rule.
DIR-819
ADVANCED
VIRTUAL SERVER
VIRTUAL SERVER
VIRTUAL SERVER
The Virtual Server option allows you to define a single public port on your router for redirection to an internal LAN IP Address and
Private LAN port if required.This feature is useful for hosting online services such as FTP or Web Servers.
Save Settings
Don’t Save Settings
24 - VIRTUAL SERVERS LIST
Remaining number of rules that can be created: 24
Port
Name
Name: Enter a name for the application you wish to apply the virtual server
to. Use the Application Name dropdown menu and the << button to
quickly select commonly used applications. The name, private port,
public port, and protocol type are automatically populated.
☐
Public Port
<<
Application Name
Computer Name
▼
▼
Schedule
Always
▼
Inbound Filter
Private Port
<<
Save Settings
Protocol
TCP
▼
IP Address
Traffic Type
Allow All
▼
Don’t Save Settings
Public Port: Enter or adjust the WAN port number in order to remap traffic.
Protocol: Select TCP or UDP from the Protocol drop-down menu.
Schedule: Select the schedule from the drop-down menu. The default is Always.
Refer to Schedules on page 110 for more information on creating
new schedules.
IP Address: Enter the IP address of the computer on your local network that you
want to allow the incoming service to or use the Computer Name
dropdown menu and the << button to quickly insert a device’s IP
address.
Private Port: Enter the LAN port number.
Inbound Filter: You may set the traffic filter to Allow All or Block All traffic.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
80
Section 3 - Configuration
Port Forwarding
Click Port Forwarding on the navigation menu to configure Port Forwarding. Port
Forwarding allows you to expose devices, applications, and servers on your local network
to the Internet. When you are satisfied with your configuration, click Save Settings.
DIR-819
24 -- PORT FORWARDING RULES
Enable: Check the box to enable this rule.
Name: Enter a name for the application you wish to apply the virtual server
to. Use the Application Name dropdown menu and the << button
to quickly select an application. The name, TCP port, and UDP port
are automatically populated.
TCP: Enter the TCP port number to forward.
Schedule: Select the schedule from the drop-down menu. The default is Always.
Refer to Schedules on page 110 for more information on creating
new schedules.
ADVANCED
PORT FORWARDING
PORT FORWARDING
PORT FORWARDING
This option is used to open multiple ports or a range of ports in your router and redirect data through those ports to a single PC on
your network. This feature allows you to enter ports in the format, Port Ranges (100-150), Individual Ports (80, 68, 888), or Mixed
(1020-5000, 689). This option is only applicable to the INTERNET session.
Save Settings
Don’t Save Settings
24 -- PORT FORWARDING RULES
Remaining number of rules that can be created: 24
Ports to Open
Name
☐
TCP
<<
Application Name
IP Address
UDP
<<
Save Settings
Computer Name
▼
Schedule
Always
▼
▼
Inbound Filter
Allow All
▼
Don’t Save Settings
IP Address: Enter the IP address of the computer on your local network that you
want to allow the incoming service to or use the Computer Name
dropdown menu and the << button to quickly insert a device’s IP
address.
UDP: Enter the UDP port number to forward.
Inbound Filter: You may set the traffic filter to Allow All or Block All traffic.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
81
Section 3 - Configuration
Application Rules
Click Port Triggering on the navigation menu to configure Port Triggering. Port triggering
allows external ports to be opened for remote access when triggered by activity by a local
computer on specified ports. When you are satisfied with your configuration, click Save
Settings.
24 -- APPLICATION RULES
Enable: Check the box to enable this rule.
Name: Enter a name for the application you wish to apply the virtual server
to. Use the Application Name dropdown menu and the << button
to quickly select an application. The name, port numbers, and traffic
type are automatically populated.
Trigger Port: Enter the trigger port.
DIR-819
ADVANCED
APPLICATION RULES
APPLICATION RULES
APPLICATION RULES
The Application Rules option is used to open single or multiple ports in your firewall when the router senses data sent to the Internet
on an outgoing "Trigger" port or port range. Special Application rules apply to all computers on your internal network.
Save Settings
Don’t Save Settings
24 -- APPLICATION RULES
Remaining number of rules that can be created: 24
Port
Trigger
☐
Name
Save Settings
Application <<
Application Name
▼
Firewall
Traffic Type
TCP
▼
TCP
▼
Schedule
Always
▼
Don’t Save Settings
Traffic Type: Select TCP, UDP, or All.
Firewall Port: Enter the firewall port to open once triggered.
Traffic Type: Select TCP, UDP, or All.
Schedule: Select the schedule from the drop-down menu. The default is Always.
Refer to Schedules on page 110 for more information on creating
new schedules.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
82
Section 3 - Configuration
QOS Engine
Click QoS Engine on the navigation menu to configure Quality of Service (QoS). QoS allows
you to prioritize Internet traffic to ensure a better web browsing experience in situations
where bandwidth is limited or large numbers of devices are in use. QoS can improve your
online experience by ensuring that specific traffic is prioritized over other network traffic,
such as VoIP, FTP, or Web. When you are satisfied with your configuration, click Save Settings.
QOS SETUP
Enable QoS: Enable or disable QoS.
Uplink Speed: Enter your Internet connection’s Uplink Speed in kbps or use the
Select Transmission Rate dropdown menu and the << button to
quickly select and populate a speed.
Downlink Speed: Enter your Internet connection’s Downlink Speed in kbps or use the
Select Transmission Rate dropdown menu and the << button to
quickly select and populate a speed.
DIR-819
ADVANCED
QOS SETTINGS
QOS ENGINE
QOS SETTINGS
Use this section to configure D-Link's QoS Engine powered by QoS Engine Technology. This QoS Engine improves your online gaming
experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web.For best performance, use
the Automatic Classification option to automatically set the priority for your applications.
Save Settings
Don’t Save Settings
QOS SETUP
Enable Qos :
☐
Uplink Speed :
kbps <<
Select Transmission Rate
▼
Downlink Speed :
kbps <<
Select Transmission Rate
▼
Queue Type : ž Strict Priority Queue š Weighted Fair Queue
Queue ID
Queue Priority
Highest
Higher
Normal
Best Effort(default)
32 -- ADD CLASSIFICATION RULE
Enable :
Queue Type: Choose either Strict Priority Queue or Weighted Fair Queue. If you
select Weighted Fair Queue, you may adjust the percentage weights
for each queue.
☐
Name :
Queue ID :
1 - Highest
Protocol :
ALL
Classify :
Upstream
▼
▼
▼
Local IP Range : Local IP Start
Click the Save Settings button before proceeding to 32 -- ADD CLASSIFICATION RULE.
Local IP End
to
Application Port :
Application Name
▼
>>
to
Remote IP Range : Remote IP Start
Remote IP End
to
Add
Cancel
CLASSIFICATION RULES
Enable
Save Settings
D-Link DIR-819 User Manual
Name
Queue ID
Protocol
Classify
Application
Port
Remote
IP Range
Local IP
Range
Don’t Save Settings
83
Section 3 - Configuration
QOS Engine (continued)
32 -- ADD CLASSIFICATION RULE
Enable: Check the box to enable this rule.
Name: Enter a name for this QoS rule.
DIR-819
ADVANCED
QOS SETTINGS
QOS ENGINE
Queue ID: Select the queue to apply this rule to.
Protocol: Select the protocol to apply the rule to: TCP, UDP, or All.
Classify: Select to apply the rule to Upstream or Downstream traffic.
Local IP Range: If you selected Upstream as the Classify type, enter the local IP
Range, excluding the router IP and broadcast IP, to apply this rule to.
For example 192.168.0.2 to 192.168.0.254.
Application Port: Enter the port range you wish to apply this rule to. Use the Application
Name dropdown menu and the << button to quickly select an
application. The protocol, and port range are automatically populated.
QOS SETTINGS
Use this section to configure D-Link's QoS Engine powered by QoS Engine Technology. This QoS Engine improves your online gaming
experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web.For best performance, use
the Automatic Classification option to automatically set the priority for your applications.
Save Settings
Don’t Save Settings
QOS SETUP
Enable Qos :
☐
Uplink Speed :
kbps <<
Select Transmission Rate
▼
Downlink Speed :
kbps <<
Select Transmission Rate
▼
Queue Type : ž Strict Priority Queue š Weighted Fair Queue
Queue ID
Queue Priority
Highest
Higher
Normal
Best Effort(default)
32 -- ADD CLASSIFICATION RULE
Enable :
☐
Name :
Queue ID :
Remote IP Range: If you selected Downstream as the Classify type, enter the Remote
IP Range, excluding the router IP and broadcast IP, to apply this rule
to. For example 192.168.0.2 to 192.168.0.254.
1 - Highest
Protocol :
ALL
Classify :
Upstream
▼
▼
▼
Local IP Range : Local IP Start
Local IP End
to
Application Port :
Application Name
▼
>>
to
Remote IP Range : Remote IP Start
Remote IP End
to
CLASSIFICATION RULES
The currently defined QoS rules are listed here.
Add
CLASSIFICATION RULES
Enable
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
Cancel
Save Settings
Name
Queue ID
Protocol
Classify
Application
Port
Remote
IP Range
Local IP
Range
Don’t Save Settings
84
Section 3 - Configuration
Network Filter
Click Network Filter on the navigation menu to configure the Network Filter. The Network
Filter allows you to allow or block a device’s access to the network or Internet based on its
MAC address. When you are satisfied with your configuration, click Save Settings.
DIR-819
24 -- MAC FILTERING RULES
Configure MAC Select the function of the MAC Filter, the options are Turn MAC
Filtering below: Filtering OFF, Turn MAC Filtering ON and ALLOW rules listed, or
Turn MAC Filtering ON and DENY rules listed.
Enable: Check the box to enable this rule.
ADVANCED
MAC ADDRESS FILTER
NETWORK FILTER
MAC ADDRESS FILTER
The MAC (Media Access Controller) Address filter option is used to control network access based on the MAC Address of the network
adapter.A MAC address is a unique ID assigned by the manufacturer of the network adapter.This feature can be configured to ALLOW
or DENY network/Internet access.
Save Settings
Don’t Save Settings
24 -- MAC FILTERING RULES
Configure MAC Filtering below:
Turn MAC Filtering OFF
MAC Address: Enter the MAC Address of the device you wish to apply the Network
Filter to. Use the Computer Name dropdown menu and the <<
button to quickly select a device. The MAC Address is automatically
populated.
▼
Turn MAC Filtering ON and ALLOW rules listed
Turn MAC Filtering ON and DENY rules listed
Remaining number of rules that can be created: 24
MAC Address
☐
DHCP Client List
<<
Save Settings
Computer Name
▼
Schedule
Always
▼
New Schedule
Don’t Save Settings
Schedule: Select the schedule from the drop-down menu. The default is Always.
Refer to Schedules on page 110 for more information on creating
new schedules.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
85
Section 3 - Configuration
Inbound Filter
Click Inbound Filter on the navigation menu to configure the Inbound Filter. The Inbound
Filter allows you to place filtering rules on a per IP basis. Using this tool you may restrict
access to or block traffic to a specific remote IP address or range. When you are satisfied
with your configuration, click Save Settings.
ADD INBOUND FILTER RULE
Name: Enter a name for this Inbound Filter.
Action: Allow or Deny traffic.
DIR-819
ADVANCED
INBOUND FILTER
INBOUND FILTER
ORANGE
OrangeText
Save Settings
Don’t Save Settings
ADD INBOUND FILTER RULE
Name :
Remote IP Range
Action :
Allow
Remote IP Range : Enable
Enable: Check the box to enable this rule.
Remote IP Start: Enter the starting IP address to apply the rule to.
Remote IP End: Enter the ending IP address to apply the rule to.
▼
Remote IP Start
0.0.0.0
255.255.255.255
☐
0.0.0.0
255.255.255.255
☐
0.0.0.0
255.255.255.255
☐
0.0.0.0
255.255.255.255
☐
0.0.0.0
255.255.255.255
☐
0.0.0.0
255.255.255.255
☐
0.0.0.0
255.255.255.255
☐
0.0.0.0
Add
INBOUND FILTER RULES LIST
The currently defined Inbound Filter rules are listed here.
Remote IP End
☐
255.255.255.255
Cancel
INBOUND FILTER RULES LIST
Name
Action
Remote IP Range
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
86
Section 3 - Configuration
Access Control
Click Access Control on the navigation menu to configure Access Control. The Access Control
function allows you to control access to the Internet. You may also monitor which web sites
were accessed. The Add Policy Wizard allows you to easily add access control policies. When
you are satisfied with your configuration, click Save Settings.
ACCESS CONTROL
Enable Access Enable or disable Access Control. You must click Save Settings after
Control: enabling Access Control before you can add policies.
Add Policy: Click this button to add a policy. Refer to Add Policy on page 88
for more information on running the Add Policy Wizard.
DIR-819
ADVANCED
ACCESS CONTROL
ACCESS CONTROL
ACCESS CONTROL
The Access Control option allows you to control access in and out of your network. Use this feature as Access Controls to only grant
access to approved sites, limit web access based on time or dates, and/or block Internet access for applications like P2P utilities or
games.
Save Settings
Don’t Save Settings
ACCESS CONTROL
Enable Access Control :
☑
Add Policy
POLICY TABLE
Enable
POLICY TABLE
Save Settings
Policy
Machine
Filtering
Logged
Schedule
Don’t Save Settings
The currently defined access control policies are listed in this table.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
87
Section 3 - Configuration
Add Policy
ADD NEW POLICY
Click Next to begin the add policy wizard.
ADD NEW POLICY
This wizard will guide you through the following steps to add a new policy for Access Control.
Step 1 - Choose a unique name for your policy
Step 2 - Select a schedule
Step 3 - Select the machine to which this policy applies
Step 4 - Select filtering method
Step 5 - Select filters
Step 6 - Configure Web Access Logging
Prev
STEP 1: CHOOSE POLICY NAME
Next
Save
Cancel
Save
Cancel
STEP 1: CHOOSE POLICY NAME
Choose a unique name for your policy.
Policy Name : Enter a name for your policy.
Policy Name :
Prev
Next
Click Next to continue.
STEP 2: SELECT SCHEDULE
STEP 2: SELECT SCHEDULE
Choose a schedule to apply to this policy.
Always
Details: Select a schedule from the drop-down menu. The default is Always.
Refer to Schedules on page 110 for more information on creating
new schedules.
Details :
Prev
▼
Always
Next
Save
Cancel
Click Next to continue.
STEP 3: SELECT MACHINE
Address Type: Choose whether this policy is applied by IP or MAC address.
IP Address: If you select IP as the address type, enter the IP address of the device
you wish to apply the policy to or use the Computer Name dropdown
menu to quickly select a computer. The IP address is automatically
populated.
STEP 3: SELECT MACHINE
Select the machine to which this policy applies.
Specify a machine with its IP or MAC address.
Address Type : ž IP š MAC
IP Address :
<<
Computer Name
▼
Machine Addres :
<<
Computer Name
▼
Clone Your PC’s MAC Address
Add
Prev
D-Link DIR-819 User Manual
Cancel
Machine
Next
Save
Cancel
88
Section 3 - Configuration
Add Policy (continued)
Machine Address: If you select MAC as the address type, enter the IP address of the
device you wish to apply the policy to or use the Computer Name
dropdown menu to quickly select a computer. The MAC address is
automatically populated. You may also use the Clone Your PC’s MAC
Address button to use the MAC address of the device you are running
the wizard from.
Add: Click this button to add the machine to the table.
STEP 3: SELECT MACHINE
Select the machine to which this policy applies.
Specify a machine with its IP or MAC address.
Address Type : ž IP š MAC
IP Address :
<<
Computer Name
▼
Machine Addres :
<<
Computer Name
▼
Clone Your PC’s MAC Address
Add
Cancel
Machine
Prev
Next
Save
Cancel
Cancel: Click this button to clear the currently configured information
Machine
IP or MAC Address: To edit a machine added to the table, click its corresponding pencil
icon. To remove a machine click its corresponding trashcan icon.
Click Next to continue.
STEP 4: SELECT FILTERING METHOD
STEP 4: SELECT FILTERING METHOD
Select the method for filtering.
Method: Select the method for filtering. The available options are Log Web
Access Only, Block All Access, or Block Some Access.
If you select Log Web Access Only or Block Some Access, click Save to finish the wizard.
Method : ž Log Web Access Only š Block All Access š Block Some Access
Prev
Next
Save
Cancel
STEP 4: SELECT FILTERING METHOD
Select the method for filtering.
Method : š Log Web Access Only š Block All Access ž Block Some Access
If you select Block Some Access, select the following options:
Apply Web Filter: Check this box to enable Web Access Logging.
Apply Web Filter :
☑
Apply Advanced Port Filters :
☑
Prev
Next
Save
Cancel
Apply Advanced Check this box to enable port filtering.
Port Filters:
Click Next to continue.
D-Link DIR-819 User Manual
89
Section 3 - Configuration
Add Policy (continued)
If you selected Block Some Access, configure the following options:
STEP 5: PORT FILTER
Enable: Check the box to enable this rule.
Name: Enter a name for port filtering rule.
Dest IP Start: Enter the start of the IP address range to filter.
Dest IP End: Enter the end of the IP address range to filter.
STEP 5: PORT FILTER
Add Port Filters Rules.
Specify rules to prohibit access to specific IP addresses and ports.
Enable
Protocol
Dest Port Start
☑
Name
0.0.0.0
Dest IP Start
255.255.255.255
Any
▼
65535
☑
0.0.0.0
255.255.255.255
Any
▼
65535
☑
0.0.0.0
255.255.255.255
Any
▼
65535
☑
0.0.0.0
255.255.255.255
Any
▼
65535
☑
0.0.0.0
255.255.255.255
Any
▼
65535
☑
0.0.0.0
255.255.255.255
Any
▼
65535
☑
0.0.0.0
255.255.255.255
Any
▼
65535
☑
0.0.0.0
255.255.255.255
Any
▼
65535
Protocol: Select the protocol to apply the port filter to. The options are Any,
ICMP, TCP, and UDP.
Prev
Dest IP End
Next
Save
Cancel
Save
Cancel
Dest Port End
If you select TCP or UDP, enter the port range:
Des Port Start: Enter the start of the port range to filter.
Des Port End: Enter the end of the port range to filter.
Click Next to continue.
STEP 6: CONFIGURE WEB ACCESS LOGGING
Web Access Enable or disable Web Access logging. You may view the web access
Logging: log from the Status > Logs section of the web configuration utility.
STEP 6: CONFIGURE WEB ACCESS LOGGING
Select the method for filtering.
Web Access Logging : ž Disabled
š Enabled
Prev
Next
Click Save to finish.
D-Link DIR-819 User Manual
90
Section 3 - Configuration
Website Filter
Click Website Filter on the navigation menu to configure the Website Filter. The Website
Filter function allows you to control access to specific websites. When you are satisfied with
your configuration, click Save Settings.
DIR-819
40 -- WEBSITE FILTERING RULES
Configure Website Select the function of the Website Filter, the options are ALLOW
Filter below: computers access to ONLY these sites or DENY computers access
to ONLY these sites.
Clear the list Click this button to clear the website filter.
below...
Website URL/ Enter website URL/Domains in each box.
Domain:
ADVANCED
WEBSITE FILTER
WEBSITE FILTER
WEBSITE FILTER
The Website Filter option allows you to set up a list of Web sites you would like to allow or deny through your network.
Save Settings
Don’t Save Settings
40 -- WEBSITE FILTERING RULES
Configure Website Filter below:
ALLOW computers access to ONLY these sites
▼
DENY computers access to ONLY these sites
Clear the list below...
Website URL/Domain
Click the Save Settings button when you are finished.
Save Settings
D-Link DIR-819 User Manual
Don’t Save Settings
91
Section 3 - Configuration
Firewall Settings
Click Firewall Settings on the navigation menu to configure the Firewall Settings. When
you are satisfied with your configuration, click Save Settings.
FIREWALL SETTINGS
Enable SPI: Enable or disable the Stateful Packet Inspection (SPI) firewall.
Disabling the firewall is not recommended.
DIR-819
ADVANCED
FIREWALL & DMZ SETTINGS
FIREWALL SETTINGS
FIREWALL & DMZ SETTINGS
DMZ means "Demilitarized Zone". DMZ allows computers behind the router firewall to be accessible to Internet traffic.Typically, your
DMZ would contain Web servers, FTP servers and others.b
ANTI-SPOOF CHECKING
Enable anti-spoof Enable or disable anti-spoof checking.
checking:
Save Settings
Don’t Save Settings
FIREWALL SETTINGS
Enable SPI :
☑
Enable anti-spoof checking :
☐
ANTI-SPOOF CHECKING
DMZ HOST
The DMZ (Demilitarized Zone) option lets you set a single computer on your network outside of the router.If you have a computer that
cannot run Internet applications successfully from behind the router, then you can place the computer into the DMZ for unrestricted
Internet access.
DMZ HOST
This option allows you to manually configure the router’s demilitarized zone (DMZ). The
DMZ should only be used as a last resort when you are having difficulty using other port
forwarding tools since the device using this IP address is not protected by the firewall. If
you use DMZ, take measures such as client-based virus protection to protect the remaining
client PCs on your LAN from possible attacks through DMZ’d device.
Note:Putting a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended
as a last resort.
Enable DMZ :
☐
DMZ IP Address :
<<
Computer Name
▼
APPLICATION LEVEL GATEWAY (ALG) CONFIGURATION
PPTP :
IPSec (VPN) :
RTSP :
SIP :
Save Settings
☑
☑
☑
☑
Don’t Save Settings
Enable DMZ: Check the box to enable the DMZ function.
DMZ Host IP Enter the IP address of the machine that you wish to place in the DMZ.
Address: If the machine receives an IP address from the DHCP server, you should
create a static DHCP reservation to ensure that the machine always
receives the same address from the DHCP server. Use the Computer
Name dropdown menu and the << button to quickly select a device.
The IP address is automatically populated.
D-Link DIR-819 User Manual
92
Section 3 - Configuration
Firewall Settings (continued)
APPLICATION LEVEL GATEWAY (ALG) CONFIGURATION
PPTP: Allows multiple machines on the LAN to connect to their corporate
network using the Point-to-Point Tunneling protocol (PPTP) based
VPNs.
DIR-819
ADVANCED
FIREWALL & DMZ SETTINGS
FIREWALL SETTINGS
IPSec (VPN): Allows VPN clients to connect to their corporate IPSec-based network.
Some VPN clients support traversal of IPSec through NAT. This
Application Level Gateway (ALG) may interfere with the operation
of such VPN clients. If you are having trouble connecting with your
corporate network, try turning this ALG off. Please check with the
system administrator of your corporate network whether your VPN
client supports NAT traversal.
RTSP: A llows applications that use Real Time Streaming Protocol (RTSP)to
receive streaming media from the Internet.
FIREWALL & DMZ SETTINGS
DMZ means "Demilitarized Zone". DMZ allows computers behind the router firewall to be accessible to Internet traffic.Typically, your
DMZ would contain Web servers, FTP servers and others.b
Save Settings
Don’t Save Settings
FIREWALL SETTINGS
Enable SPI :
☑
Enable anti-spoof checking :
☐
ANTI-SPOOF CHECKING
DMZ HOST
The DMZ (Demilitarized Zone) option lets you set a single computer on your network outside of the router.If you have a computer that
cannot run Internet applications successfully from behind the router, then you can place the computer into the DMZ for unrestricted
Internet access.
Note:Putting a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended
as a last resort.
Enable DMZ :
☐
DMZ IP Address :
<<
Computer Name
SIP: Enabling Session Initiation Protocol (SIP) allows devices and
applications using VoIP (Voice over IP). Some VoIP applications and
devices have the ability to discover NAT devices and work around
them. This ALG may interfere with the operation of such devices. If
you are having trouble making VoIP calls, try turning this ALG off.
▼
APPLICATION LEVEL GATEWAY (ALG) CONFIGURATION
PPTP :
IPSec (VPN) :
RTSP :
SIP :
Save Settings
☑
☑
☑
☑
Don’t Save Settings
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
93
Section 3 - Configuration
Routing
Click Routing on the navigation menu to configure Routing. The routing page allows you
to define custom static routes to control the route which your data takes. When you are
satisfied with your configuration, click Save Settings.
DIR-819
32 -- ROUTE LIST
Enable: Check the box to enable this rule.
ADVANCED
ROUTING
ROUTING
ROUTING
The Routing option allows you to define static routes to specific destinations.
Name: Enter a name for this static route.
Destination IP: Enter the destination IP address.
Save Settings
Don’t Save Settings
24 -- APPLICATION RULES
Remaining number of rules that can be created: 24
Metric
Gateway: Enter the gateway IP address.
Metric: Enter the metric value between 1-255.
☐
Name
Destination IP
Netmask
Gateway
Save Settings
Interface
WAN(172.17.5.x)
▼
Don’t Save Settings
Interface: Select the Interface from the drop-down menu.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
94
Section 3 - Configuration
Advanced Wireless
Click Advanced Wireless on the navigation menu to configure the advanced wireless
options. When you are satisfied with your configuration, click Save Settings.
ADVANCED WIRELESS SETTINGS
Wireless Band: 2.4 GHz Band
DIR-819
ADVANCED
ADVANCED WIRELESS SETTINGS
ADVANCED WIRELESS
ADVANCED WIRELESS SETTINGS
Transmit Power: Select the desired wireless transmission power.
WLAN Partition: Check this box to enable user isolation. User isolation forces wireless
clients to communicate with each other through the access point.
These options are for users that wish to change the behavior of their 802.11n wireless radio from the standard settings. We do not
recommend changing these settings from the factory defaults. Incorrect settings may impact the performance of your wireless radio.
The default settings should provide the best wireless radio performance in most environments.
Save Settings
Don’t Save Settings
ADVANCED WIRELESS SETTINGS
Wireless Band : 2.4GHz Band
Transmit Power :
WMM Enable: Enable or Disable Wi-Fi MultiMedia QoS.
WLAN Partition :
WMM Enable :
High
▼
☐
☑
HT 20/40 Coexistence : ž Enable š Disable
HT 20/40 Enable or disable HT20/40 Coexistence.
Coexistence:
ADVANCED WIRELESS SETTINGS
Wireless Band : 5GHz Band
Transmit Power :
WLAN Partition :
WMM Enable :
ADVANCED WIRELESS SETTINGS
Save Settings
High
▼
☑
☑
Don’t Save Settings
Wireless Band: 5 GHz Band
Transmit Power: Select the desired wireless transmission power.
WLAN Partition: Check this box to enable user isolation. User isolation forces wireless
clients to communicate with each other through the access point.
WMM Enable: Enable or Disable Wi-Fi MultiMedia QoS.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
95
Section 3 - Configuration
Wi-Fi Protected Setup
Click Wi-Fi Protected Setup on the navigation menu to configure the Wi-Fi Protected Setup
(WPS) feature. Refer to WPS Button on page 122 for more information about WPS. When
you are satisfied with your configuration, click Save Settings.
DIR-819
WI-FI PROTECTED SETUP
Enable: Check the box to enable WPS.
WiFi Protected The current status of the WPS feature is displayed here.
Setup:
Lock WPS-PIN Enable or disable WPS-PIN functionality.
Setup:
ADVANCED
WI-FI PROTECTED SETUP
WI-FI PROTECTED SETUP
WI-FI PROTECTED SETUP
Wi-Fi Protected Setup is used to easily add devices to a network using a PIN or button press. Devices must support Wi-Fi Protected
Setup in order to be configured by this method.
If the PIN changes, the new PIN will be used in following Wi-Fi Protected Setup process. Clicking on ''Don't Save Settings'' button will
not reset the PIN.
However, if the new PIN is not saved, it will get lost when the device reboots or loses power.
Save Settings
Don’t Save Settings
WI-FI PROTECTED SETUP
Enable :
☑
WiFi Protected Setup : Enabled/Configured
Lock WPS-PIN Setup :
☐
PIN SETTINGS
PIN : 49445183
PIN SETTINGS
PIN: The currently defined WPS-PIN is displyaed here.
Reset PIN to Default Click this button to reset the WPS-PIN to the factory default.
Reset PIN to Default
Generate New Pin
ADD WIRELESS STATION
Connect your Wireless Device
Save Settings
Don’t Save Settings
Generate New PIN Click this button to generate a new WPS PIN.
ADD WIRELESS STATION
Connect your Click this button to launch the WPS Add Device Wizard. Refer to Add
Wireless Device: Wireless Device with WPS on page 47 for more information.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
96
Section 3 - Configuration
Advanced Network
Click Advanced Network on the navigation menu to configure the Advanced Wireless
settings. This page allows for the configuration of miscillaneous settings. When you are
satisfied with your configuration, click Save Settings.
DIR-819
UPNP
Enable UPnP IGD: Click Enable to use the UPnP feature. UPnP provides compatibility
with networking equipment, software, and peripherals.
ADVANCED
ADVANCED NETWORK SETTINGS
These options are for users that wish to change the LAN settings. We do not recommend changing these settings from factory default.
Changing these settings may affect the behavior of your network.
Save Settings
WAN PING
Enable WAN Ping Enable or disable the router to reply to pings.
Response:
ADVANCED NETWORK SETTINGS
ADVANCED NETWORK
Don’t Save Settings
UPNP
Universal Plug and Play(UPnP) supports peer-to-peer Plug and Play functionality for network devices.
Enable UPnP IGD :
☐
WAN PING
If you enable this feature, the WAN port of your router will respond to ping requests from the Internet that are sent to the WAN IP
Address.
Enable WAN Ping Response :
☐
WAN PORT SPEED
WAN Port Speed :
WAN PORT SPEED
WAN Port Speed: You may set the port speed of the Internet port to 10 Mbps, 100 Mbps,
or Auto 10/100Mbps. Using Auto 10/100Mbps is recommended.
Auto 10/100Mbps
▼
MULTICAST STREAMS
Enable Multicast Streams :
☐
IPV6 MULTICAST STREAMS
Enable IPv6 Multicast Streams :
Save Settings
☐
Don’t Save Settings
MULTICAST STREAMS
Enable Multicast Enable to allow IPv4 multicast traffic to pass through the router from
Streams: the Internet.
IPV6 MULTICAST STREAMS
Enable IPv6 Enable to allow IPv6 multicast traffic to pass through the router from
Multicast Streams: the Internet.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
97
Section 3 - Configuration
Guest Zone
Click Guest Zone on the navigation menu to configure Guest Zones. The guest zone feature
allows you to create wireless networks for visitors. This allows you to keep your devices
secure. When you are satisfied with your configuration, click Save Settings.
DIR-819
GUEST ZONE
Enable Routing If a guest zone or zones are enabled and this option is disabled, guest
Between Zones: device network connectivity is restricted to the Internet. If this option
is enabled, guest devices are allowed access to other local network
devices.
ADVANCED
GUEST ZONE
GUEST ZONE
GUEST ZONE
Use this section to configure the guest zone settings of your router. The guest zone provide a separate network zone for guest to
access Internet.
Save Settings
Don’t Save Settings
GUEST ZONE
Enable Routing Between Zones :
☑
Enable Guest Zone :
☑
SESSION 2.4GHZ
SESSION 2.4GHZ / SESSION 5GHZ
Enable Guest Zone: Enable or disable this guest wireless network. From the drop down
menu you may apply a schedule to enable or disable this wireless
network. Click New Schedule to create a new schedule. Refer to
Schedules on page 110 for more information.
Always
▼
Wireless Network Name :
Security Mode :
(Also called the SSID)
None
▼
SESSION 5GHZ
Enable Guest Zone :
☑
Always
▼
New Schedule
Wireless Band : 5GHz Band
Wireless Network Name :
Wireless Band: The current wireless band is displayed here, either 2.4GHz or 5GHz.
New Schedule
Wireless Band : 2.4GHz Band
Security Mode :
Save Settings
(Also called the SSID)
None
▼
Don’t Save Settings
Wireless Network Create a name for your wireless network.
Name:
Security Mode: Select a wireless security encryption option. The options are
None, WEP, WPA-Personal, and WPA-Enterprise. Using WPA is
recommended. Refer to Wireless Security Mode on page 52 for
more information.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
98
Section 3 - Configuration
IPv6 Firewall
Click IPv6 Firewall on the navigation menu to configure the IPv6 Firewall Settings. When
you are satisfied with your configuration, click Save Settings.
IPV6 SIMPLE SECURITY
Enable IPv6 Simple Enable or disable the IPv6 firewall.
Security:
DIR-819
ADVANCED
IPV6 FIREWALL
IPV6 FIREWALL
IPV6 FIREWALL
The firewall settings section is an advance feature used to allow or deny traffic from passing through the device. It works in the same
way as IP Filters with additional settings. You can create more detailed rules for the device.
20 -- IPV6 FIREWALL RULES
Configure IPv6 Select the function of the IPv6 Filter, the options are Turn IPv6
Filtering below: Filtering OFF, Turn IPv6 Filtering ON and ALLOW rules listed, Turn
IPv6 Filtering ON and DENY rules listed.
Save Settings
Don’t Save Settings
IPV6 SIMPLE SECURITY
Enable IPv6 Simple Security :
☐
20 -- IPV6 FIREWALL RULES
Remaining number of rules that can be created: 24
Configure IPv6 Filtering below:
Turn IPv6 Filtering OFF
▼
Turn IPv6 Filtering ON and ALLOW rules listed
Enable: Check the box to enable this rule.
Turn IPv6 Filtering ON and DENY rules listed
Schedule
Name
Always
Name: Enter a name for the rule.
Schedule: Select the schedule from the drop-down menu. The default is Always.
Refer to Schedules on page 110 for more information on creating
new schedules.
☐
Source
Dest
Save Settings
Interface
LAN
Protocol
ALL
▼
▼
IP Address /PrefixLength
Interface
LAN
▼
IP Address /PrefixLength
▼
Port Range
Don’t Save Settings
Source Interface: Select the source interface, WAN or LAN, from the drop down menu.
Source IP Address / Enter the source IP address and specify the prefix length for the rule.
PrefixLength:
Protocol: Select the protocol to apply the rule to, either ALL, TCP, UDP, or ICMP.
Destination Select the destination interface, WAN or LAN, from the drop down
Interface: menu.
D-Link DIR-819 User Manual
99
Section 3 - Configuration
IPv6 Firewall (continued)
Destination Enter the destination IP address and specify the prefix length for the
IP Address / rule.
PrefixLength:
Port Range: Enter the port range to apply the rule to. If the protocol is set as ALL
or ICMP this feature is disabled.
Click the Save Settings button when you are finished.
DIR-819
ADVANCED
IPV6 FIREWALL
IPV6 FIREWALL
IPV6 FIREWALL
The firewall settings section is an advance feature used to allow or deny traffic from passing through the device. It works in the same
way as IP Filters with additional settings. You can create more detailed rules for the device.
Save Settings
Don’t Save Settings
IPV6 SIMPLE SECURITY
Enable IPv6 Simple Security :
☐
20 -- IPV6 FIREWALL RULES
Remaining number of rules that can be created: 24
Configure IPv6 Filtering below:
Turn IPv6 Filtering OFF
▼
Turn IPv6 Filtering ON and ALLOW rules listed
Turn IPv6 Filtering ON and DENY rules listed
Schedule
Name
Always
☐
Source
Dest
Save Settings
D-Link DIR-819 User Manual
Interface
LAN
Protocol
LAN
▼
▼
IP Address /PrefixLength
Interface
LAN
▼
IP Address /PrefixLength
▼
Port Range
Don’t Save Settings
100
Section 3 - Configuration
IPv6 Routing
Click IPv6 Routing on the navigation menu to configure IPv6 Routing. The routing page
allows you to define custom static routes to control the route which your data takes. When
you are satisfied with your configuration, click Save Settings.
DIR-819
10 -- ROUTE LIST
Enable: Check the box to enable this rule.
ADVANCED
ROUTING
IPV6 ROUTING
ROUTING
This Routing page allows you to specify custom routes that determine how data is moved around your network.
Name: Enter a name for this IPv6 static route.
Destination IPv6 / Enter the destination IPv6 address and Prefix Length.
Prefix Length:
Save Settings
Don’t Save Settings
10 -- ROUTE LIST
Destination IPv6 / Prefix Length
Name
☐
Metric: Enter the metric value between 1-255.
Interface: Select the Interface from the drop-down menu.
Metric
256
Save Settings
Interface
NULL
Gateway
▼
Don’t Save Settings
Gateway: Enter the gateway IPv6 address.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
101
Section 3 - Configuration
Tools
The Tools tab provides access to administration related settings of your DIR-819.
DIR-819
SETUP
ADVANCED
TOOLS
STATUS
ADMIN
ADMINISTRATOR SETTINGS
TIME
The 'admin' account can access the management interface. The admin has read/write access and can change password.
By default there is no password configured. It is highly recommended that you create a password to keep your router secure.
SUPPORT
SYSLOG
Save Settings
SYSTEM
Don’t Save Settings
FIRMWARE
ADMIN PASSWORD
DYNAMIC DNS
Please enter the same password into both boxes, for confirmation.
Password :
SYSTEM CHECK
Verify Password :
SCHEDULES
ADMINISTRATION
Enable HTTPS Server :
Enable Remote Management :
Remote Admin Port :
Save Settings
☐
☐
8080
Remote Admin Inbound Filter :
Allow All
Details :
Allow All
Use HTTPS:
☐
▼
Don’t Save Settings
DIR-819
To return to this Web UI Table of Contents page, simply click the D-Link logo on the top
right of each page.
D-Link DIR-819 User Manual
INTERNET
SETUP
INTERNET CONNECTION
102
Section 3 - Configuration
Admin
Click Admin on the navigation menu to configure the administration settings. This page
allows you to configure access to the web configuration utility. When you are satisfied with
your configuration, click Save Settings.
DIR-819
ADMIN PASSWORD
Password: Enter the new password for the admin account.
Verify Password: Enter the new password for the admin account one more time.
TOOLS
ADMINISTRATOR SETTINGS
ADMIN
ADMINISTRATOR SETTINGS
The 'admin' account can access the management interface. The admin has read/write access and can change password.
By default there is no password configured. It is highly recommended that you create a password to keep your router secure.
Save Settings
Don’t Save Settings
ADMIN PASSWORD
ADMINISTRATION
Enable HTTPS Check to enable HTTPS to connect to the router securely. You may
Server:: access the web configuration utility using https://dlinkrouter.local./.
Please enter the same password into both boxes, for confirmation.
Password :
Verify Password :
ADMINISTRATION
Enable HTTPS Server :
Enable Remote Management :
Enable Remote Remote management allows the DIR-819 to be configured from the
Management: Internet by a web browser. A password is still required to access the
web management interface.
Remote Admin Port :
Save Settings
☐
☐
8080
Remote Admin Inbound Filter :
Allow All
Details :
Allow All
Use HTTPS:
☐
▼
Don’t Save Settings
Remote Admin Enter the port number you wish to use to access the DIR-819’s web
Port: configuration utility. Example: http://x.x.x.x:8080 where x.x.x.x is
the Internet IP address of the DIR-819 and 8080 is the port used for
the web management interface.
Note: If you enabled HTTPS Server and wish to access the router remotely
and securely, you may enter https:// at the beginning of the address.
Remote Admin You may select an inbound filter from the drop down menu to restrict
Inbound Filter: remote administration. Refer to Inbound Filter on page 86 for
more information.
Details: The current status of the Remote Administration Inbound filter is
displayed here.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
103
Section 3 - Configuration
Time
Click Time on the navigation menu to configure the time. When you are satisfied with your
configuration, click Save Settings.
TIME AND DATE CONFIGURATION
Time: The currently set time on the router is displayed.
Time Zone: Displays the current date and time of the router.
Enable Daylight Enable or disable daylight saving time.
Saving:
DIR-819
TIME AND DATE
TIME
TIME AND DATE
The Time and Date Configuration option allows you to configure, update, and maintain the correct time on the internal system clock.
From this section you can set the time zone you are in and set the NTP (Network Time Protocol) Server. Daylight Saving can also be
configured to adjust the time when needed.
Save Settings
Don’t Save Settings
TIME AND DATE CONFIGURATION
Time : 2016-09-19 12:00:00
Time Zone :
Daylight Saving Select the daylight saving offset if Daylight Saving time will be used.
Offset:
Daylight Saving Select the date range for when to start and stop daylight savings time.
Dates:
TOOLS
Enable Daylight Saving :
Daylight Saving Offset :
Automatically
synchronize with
D-Link’s Internet
time server:
Enable this option to get the current time from an NTP server on the
Internet. To configure the router's time and date manually, disable
this option and use the drop-down menus that appear to input the
time and date.
-02:00
▼
▼
Daylight Saving Dates :
Month
Week
Day of Week
Time
DST Start
Mar
▼
2nd
▼
Sun
▼
2 am
▼
DST End
Nov
▼
1st
▼
Sun
▼
2 am
▼
AUTOMATIC TIME AND DATE CONFIGURATION
☑ Automatically synchronize with D-Link’s Internet time server
NTP Server Used :
AUTOMATIC TIME AND DATE CONFIGURATION
(GMT+08:00) Taipei
☑
ntp1.dlink.com
▼
SET THE TIME AND DATE MANUALLY
Year
2016
▼
Month
Sep
▼
Day
19
▼
Hour
▼
Minute
▼
Second
59
▼
Sync. your computer’s time settings
Save Settings
Don’t Save Settings
NTP Server Used: If you enable this option, select an NTP server from the drop-down
menu.
SET THE TIME AND DATE MANUALLY
You may manually set the time from this option or set the time by clicking Sync. your
computer’s time settings.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
104
Section 3 - Configuration
Syslog
Click Syslog on the navigation menu to configure the system log settings. This device
maintains a running log of events which can be sent to a syslog server. Refer to Logs on
page 114 for an example system log. When you are satisfied with your configuration, click
Save Settings.
SYSLOG SETTINGS
Enable Logging to Enable or disable the sending of router logs to a syslog server.
SysLog Server:
If you enable Logging to SysLog Server, enter the Syslog Server IP Address:
DIR-819
TOOLS
SYSLOG
SYSLOG
SYSLOG
The SysLog options allow you to send log information to a Syslog Server.
Save Settings
Don’t Save Settings
SYSLOG SETTINGS
Enable Logging To SysLog Server:
Syslog Server IP Address:
SysLog Server IP Enter the IP address of the syslog server. Use the Computer Name
Address: dropdown menu and the << button to quickly select a device. The
IP address is automatically populated.
Save Settings
☑
<<
Computer Name
▼
Don’t Save Settings
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
105
Section 3 - Configuration
System
Click System on the navigation menu to configure the system settings. This section allows
you to manage the router’s configuration settings, reboot the router, and restore the router
to the factory default settings. Restoring the unit to the factory default settings will erase
all settings, including any rules that you’ve created.
SAVE AND RESTORE SETTINGS
Save Settings To Use this option to save the current router configuration settings to
Local Hard Drive: a file on the hard disk of the computer you are using. Click the Save
Configuration button. A file dialog will appear, allowing you to select
a location and file name for the settings.
DIR-819
TOOLS
SAVE AND RESTORE SETTINGS
SYSTEM
SAVE AND RESTORE SETTINGS
Once the router is configured you can save the configuration settings to a configuration file on your hard drive. You also have the
option to load configuration settings, or restore the factory default settings.
SAVE AND RESTORE SETTINGS
Save Settings To Local Hard Drive :
Load Settings From Local Hard Drive :
Save Configuration
Choose File
No file chosen
Restore Configuration From File
Load Settings From Use this option to load previously saved router configuration
Local Hard Drive: settings. Use the Choose File option to find a previously saved file
of configuration settings and then click the Restore Configuration
From File to transfer those settings to the router.
Restore To Factory Default Settings :
Reboot The Device :
Clear Language Pack :
Restore Factory Defaults
Reboot the Device
Clear
Restore To Factory This option will restore all configuration settings back to the settings
Default Settings: that were in effect at the time the router was shipped from the factory.
Any settings that have not been saved will be lost, including any
rules that you have created. If you want to save the current router
configuration settings, use the Save button above.
Reboot The Device: Click this button to reboot the device.
Clear Language If the device is of other language than English, clicking this button
Pack: to convert the router’s language back to English.
D-Link DIR-819 User Manual
106
Section 3 - Configuration
Firmware
Click Firmware on the navigation menu to configure the firmware. Please check
the D-Link support website for firmware updates and new language packs at
http://support.dlink.com. Be sure to keep your router firmware updated to help protect
against the latest cyber threats.
FIRMWARE INFORMATION
Current Firmware The current firmware version is displayed here.
Version:
Current Firmware The release date and time of the current firmware is displayed here.
Time:
DIR-819
TOOLS
FIRMWARE UPDATE
FIRMWARE
FIRMWARE UPDATE
There may be new firmware for your router to improve functionality and performance.
Click here to check for an upgrade on our support site.
To upgrade the firmware, locate the upgrade file on the local hard drive with the Browse button. Once you have found the file to be
used, click the Upload button to start the firmware upgrade.
The language pack allows you to change the language of the user interface on the router. We suggest that you upgrade your current
language pack if you upgrade the firmware. This ensures that any changes in the firmware are displayed correctly.
To upgrade the language pack, locate the upgrade file on the local hard drive with the Browse button. Once you have found the file to
be used, click the Upload button to start the language pack upgrade.
SAVE AND RESTORE SETTINGS
Current Firmware Version : V1.01
Check Online Now Click this button to prompt the router to check for a new firmware
for Latest Firmware version.
Version:
Current Firmware Time : Sep-29-2016T21:40:49
Check Online Now for Latest Firmware Version :
Check Now
FIRMWARE UPGRADE
Note: Some firmware upgrades reset the configuration options to the factory defaults. Before performing an upgrade,
be sure to save the current configuration.
To upgrade the firmware, your PC must have a wired connection to the router. Enter the name of the firmware upgrade
file, and click on the Upload button.
Upload :
FIRMWARE UPGRADE
Upload: Select a file to upgrade your device with by clicking the Choose File
button. Click the Upload button to begin the firmware upgrade.
Clear Config :
Choose File
No file chosen
☐
Upload
LANGUAGE PACK UPGRADE
Upload :
Choose File
No file chosen
Upload
Clear Config: Check this box to clear the current settings of your DIR-819 once the
firmware update is applied.
LANGUAGE PACK UPGRADE
Upload: You can change the language of the web UI by uploading language
packs. Select a file to upgrade your device with by clicking the Choose
File button. Click the Upload button to begin the firmware upgrade.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
107
Section 3 - Configuration
Dynamic DNS
Click Dynamic DNS on the navigation menu to configure the Dynamic Domain Name Server
(DDNS) client. DDNS makes accessing your network from the Internet easier by providing
you with an easy to use web address. Owners of D-Link routers can use the dlinkdns service.
DIR-819
DYNAMIC DNS SETTINGS
Enable Dynamic Enable or disable the Dynamic DNS feature.
DNS:
If you enabled Dynamic DNS, configure the following settings:
Server Address: Enter the IP address of your DDNS provider. Use the Select Dynamic
DNS Server dropdown menu and the << button to quickly select a
device. The IP address is automatically populated.
DYNAMIC DNS
DYNAMIC DNS
DYNAMIC DNS
The Dynamic DNS feature allows you to host a server (Web, FTP, Game Server, etc...) using a domain name that you have purchased
(www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign
dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter your host name to connect to your game
server no matter what your IP address is.
Save Settings
Don’t Save Settings
DYNAMIC DNS SETTINGS
Enable Dynamic DNS :
☑
Server Address :
<<
Select Dynamic DNS Server
▼
Host Name :
Username :
Host Name: Enter the host name that you registered with your DDNS service
provider.
Username: Enter your DDNS username.
TOOLS
Password :
···
Verify Password :
···
Timeout :
576
(Times)
Status : Disconnected
Save Settings
Don’t Save Settings
Password: Enter your DDNS password.
Verify Password: Enter your DDNS password one more time.
Timeout: Enter a timeout time (in hours) before the DDNS information is
automatically updated.
Status: The current status of your DDNS service is displayed here.
Click the Save Settings button when you are finished.
D-Link DIR-819 User Manual
108
Section 3 - Configuration
System Check
Click System Check on the navigation menu to test your connection to the Internet.
PING TEST
Host Name or IP Enter either an IP address or web address that you wish to Ping and
Address: click Ping.
DIR-819
TOOLS
SYSTEM CHECK
PING TEST
PING TEST
Ping Test sends "ping" packets to test a computer on the Internet.
IPV6 PING TEST
Host Name or IPv6 Enter either an IPv6 address or web address that you wish to Ping
Address: and click Ping.
PING TEST
Host Name or IP Address :
Ping
Host Name or IPv6 Address :
Ping
IPV6 PING TEST
PING RESULT
Result here
PING RESULT
The results of the test are displayed in this dialog box.
D-Link DIR-819 User Manual
109
Section 3 - Configuration
Schedules
Click Schedules on the navigation menu to configure the system schedules. Several router
functions be operated according to a pre-configured schedule which may be created from
this page.
DIR-819
10 -- ADD SCHEDULE RULE
If you wish to create a new schedule, fill in the following fields:
Name: Enter a name for your new schedule.
TOOLS
SCHEDULES
SCHEDULES
SCHEDULES
The Schedule configuration option is used to manage schedule rules for "WAN", "Wireless", "Virtual Server", "Port Forwarding",
"Applications" and "Network Filter".
10 -- ADD SCHEDULE RULE
Name :
Day(s): Choose to have the schedule apply to All Week or Select Days and
check the boxes of the days to apply the rules to.
All Day - 24 hrs: Check this box to have the rule apply all day or leave this box
unchecked at fill in the Start Time and End Time fields.
Start Time: Enter the start time for this rule to start.
Day(s) : ž All Week š Select Days
All Day - 24 hrs :
☐
☐
Sun
☐
Mon
Start Time :
End Time :
Add
☐
Tue
☐
Wed
☐
Thu
☐
Frid
☐
Sat
(hour:minute)
(hour:minute)
Cancel
SCHEDULE RULES LIST
Name
Days
Time Frame
End Time: Enter the end time for this rule to stop.
Click the Add button when you are satisfied with your new schedule.
SCHEDULE RULES LIST
The currently added rules are displayed in this table. You may edit or delete a rule by clicking
on its corresponding Edit or Delete buttons.
D-Link DIR-819 User Manual
110
Section 3 - Configuration
Status
The Status tab provides information about the DIR-819’s current status.
DIR-819
DEVICE INFO
LOGS
STATISTICS
SETUP
TOOLS
STATUS
SUPPORT
DEVICE INFORMATION
All of your Internet and network connection details are displayed on this page. The firmware version is also displayed here.
GENERAL
INTERNET SESSIONS
Time: 2016-09-19 13:00
Current Firmware Version : V1.01
WIRELESS
ROUTING
ADVANCED
WAN
IPV6
IPV6 ROUTING
Connection Type : DHCP Client
Cable Status : Connected
Network Status : Connected
Renew
Release
Connection Up Time : 0 Day 0 Hour 0 Min 0 Sec
MAC Address : ff:ff:ff:ff:ff:ff
IP Address : 192.168.0.1
DIR-819
To return to this Web UI Table of Contents page, simply click the D-Link logo on the top
right of each page.
D-Link DIR-819 User Manual
INTERNET
SETUP
INTERNET CONNECTION
111
Section 3 - Configuration
Device Info
Click Device Info to see current information about the DIR-819. This pages displays LAN,
WAN (Internet), and Wireless information.
GENERAL
The DIR-819’s currently set time and firmware are displayed here.
DIR-819
STATUS
DEVICE INFORMATION
DEVICE INFO
DEVICE INFORMATION
All of your Internet and network connection details are displayed on this page. The firmware version is also displayed here.
WAN
The DIR-819’s currently configured Internet connection settings are displayed here.
GENERAL
Time: 2016-09-19 13:00
Current Firmware Version : V1.01
WAN
Connection Type : DHCP Client
Cable Status : Connected
Network Status : Connected
LAN
Renew
Release
Connection Up Time : 0 Day 0 Hour 0 Min 0 Sec
The DIR-819’s currently configured local network settings are displayed here.
MAC Address : ff:ff:ff:ff:ff:ff
IP Address : 192.168.0.1
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
WIRELESS LAN
The DIR-819’s currently configured 2.4 GHz wireless network settings are displayed here.
Primary DNS Server : 192.168.0.1
Secondary DNS Server : 192.168.0.1
LAN
MAC Address : ff:ff:ff:ff:ff:ff
IP Address : 192.168.0.1
Subnet Mask 255.255.255.0
DHCP Server : Enabled
WIRELESS LAN
Wireless Radio : Enabled
MAC Address : ff:ff:ff:ff:ff:ff
802.11 Mode : Mixed 802.11n, 802.11g and 802.11b
Channel Width : 20/40MHz
Channel : 1
Network Name (SSID) : Your_2.4GHz_Network
Wi-Fi Protected Setup : Enabled/Not configured
Security : NONE
Guest Zone Wireless Radio : Disabled
Guest Zone Network Name (SSID) :
Guest Zone Security : NONE
D-Link DIR-819 User Manual
112
Section 3 - Configuration
Device Info (continued)
WIRELESS LAN2
WIRELESS LAN2
Wireless Radio : Enabled
MAC Address : ff:ff:ff:ff:ff:ff
The DIR-819’s currently configured 5 GHz wireless network settings are displayed here.
802.11 Mode : Mixed 802.11ac, 802.11n and 802.11a
Channel Width : 20/40/80MHz
Channel : 161
Network Name (SSID) : Your_5GHz_Network
LAN COMPUTERS
Wi-Fi Protected Setup : Enabled/Not configured
Security : NONE
The devices currently connected to the DIR-819’s are displayed here.
Guest Zone Wireless Radio : Disabled
Guest Zone Network Name (SSID) :
Guest Zone Security : NONE
LAN COMPUTERS
IGMP MULTICAST MEMBERSHIPS
The DIR-819’s current IGMP multicast information is displayed here.
MAC Address
IP Address
Name(if any)
ff:ff:ff:ff:ff:ff
IGMP MULTICAST MEMBERSHIPS
IPv4 Multicast Group Address
IPv6 Multicast Group Address
D-Link DIR-819 User Manual
113
Section 3 - Configuration
Logs
Click Logs on the navigation menu to view the system log. This device maintains a running
log of events which can be sent to a syslog server. Refer to Syslog on page 105 for more
information on configuring the system log.
DIR-819
SAVE LOG FILE
Click the Save button to save the log file to your local hard drive.
STATUS
VIEW LOG
LOGS
VIEW LOG
The View Log displays the activities occurring on the router.
WAN
Log Type: To change the type of information to view and then click the Save
Settings button.
Log Level: To change the levl of information to view and then click the Save
Settings button.
Save Settings
Don’t Save Settings
SAVE LOG FILE
Save Log File To Local Hard Drive.
Save
WAN
Log Type : ž System
š Firewall & Security
š Router Status
Log Level : ž Critical
š Warning
š Information
LOG FILES
First Page Last Page
Previous
Next
Clear
1/1
Time
Message
Sep 19 09:15:05 2016
User Admin login success
LOG FILES
Click the navigation buttons to view the log file.
D-Link DIR-819 User Manual
114
Section 3 - Configuration
Statistics
Click Statistics on the navigation menu to view statistics on the amount of traffic which
has passed through the DIR-819’s interfaces. Click the Refresh Statistics button to view
the latest numbers.
DIR-819
STATUS
TRAFFIC STATISTICS
STATISTICS
TRAFFIC STATISTICS
Traffic Statistics displays Receive and Transmit packets passing through the device.
Refresh Statistics
LAN STATISTICS
Sent :
Received :
TX Packets Dropped :
RX Packets Dropped :
Collisions :
Errors :
Sent :
Received :
TX Packets Dropped :
RX Packets Dropped :
Collisions :
Errors :
WAN STATISTICS
WIRELESS STATISTICS - 2.4GHZ BAND
Sent :
Received :
TX Packets Dropped :
RX Packets Dropped :
Collisions :
Errors :
Sent :
Received :
TX Packets Dropped :
RX Packets Dropped :
Collisions :
Errors :
WIRELESS STATISTICS - 5GHZ BAND
D-Link DIR-819 User Manual
115
Section 3 - Configuration
Internet Sessions
Click Internet Sessions on the navigation menu to view information about currently active
Internet connections. This page helps to diagnose connectivity issues. Click the Refresh
button to view the latest information.
DIR-819
STATUS
INTERNET SESSIONS
INTERNET SESSIONS
INTERNET SESSIONS
This page displays Source and Destination sessions passing through the device.
Refresh
D-Link DIR-819 User Manual
IP
Protocol
NAT
Internet
192.168.0.100
UDP
54674
192.168.0.1
State
Dir
Time Out
Out
60
116
Section 3 - Configuration
Wireless
Click Wireless on the navigation menu to view information about currently connected
wireless clients. You may view each client’s MAC address, IP address, 802.11 mode, speed,
and signal strength.
DIR-819
STATUS
CONNECTED WIRELESS CLIENT LIST
WIRELESS
CONNECTED WIRELESS CLIENT LISTV
View the wireless clients that are connected to the router. (A client might linger in the list for a few minutes after an unexpected
disconnect.)
NUMBER OF WIRELESS CLIENTS - 2.4GHZ BAND : 0
MAC Address
IP Address
Mode
Rate(Mbps)
Signal (%)
Mode
Rate(Mbps)
Signal (%)
NUMBER OF WIRELESS CLIENTS - 5GHZ BAND : 0
MAC Address
D-Link DIR-819 User Manual
IP Address
117
Section 3 - Configuration
Routing
Click Routing to view the currently configured IPv4 routing table.
DIR-819
STATUS
ROUTING
ROUTING
ROUTING
Routing Table
This page displays the routing details configured for your router.
ROUTING TABLE
D-Link DIR-819 User Manual
Destination
Gateway
Genmask
Metric
Iface
Creator
192.168.0.100
0.0.0.0
255.255.255.0
eth1
118
Section 3 - Configuration
IPV6
Click IPv6 to view the currently IPv6 information.
IPV6 CONNECTION INFORMATION
IPv6 Connection The currently configured IPv6 connection type is listed here.
Type:
IPv6 Default The current IPv6 default gateway is listed here.
Gateway:
DIR-819
STATUS
IPV6 NETWORK INFORMATION
IPV6
IPV6 NETWORK INFORMATION
All of your IPv6 Internet and network connection details are displayed on this
IPV6 CONNECTION INFORMATION
IPv6 Connection Type : Link-Lcoal
LAN IPv6 Link-Local The current IPv6 Link-Local address is listed here.
Address:
IPv6 Default Gateway : NONE
LAN IPv6 Link-Local Address : ffff::fff:fff:ffff:ffff
LAN IPV6 COMPUTERS
IPv6 Address
Name(if any)
LAN IPV6 COMPUTERS
The currently connected IPv6 computers are listed in this table.
D-Link DIR-819 User Manual
119
Section 3 - Configuration
IPv6 Routing
Click IPv6 Routing to view the currently configured IPv6 routing table.
DIR-819
STATUS
IPV6 ROUTING
IPV6 ROUTING
IPV6 ROUTING
This page displays IPV6 routing details configured for your router.
IPV6 ROUTING TABLE
D-Link DIR-819 User Manual
Destination IP
Gateway
Metric
Interface
fe800000000000000000000000
000000/64
000000000000000000000000
00000000
256
br0
120
Section 3 - Configuration
Support
DIR-819
SETUP
MENU
IPV6 ROUTING
SETUP
•
•
•
•
ADVANCED
TOOLS
STATUS
ADVANCED
TOOLS
STATUS
SUPPORT
Setup
Advanced
Tools
Status
SETUP HELP
•
•
•
•
Internet
Wireless Settings
Network Settings
IPv6
ADVANCED HELP
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Virtual Server
Port Forwarding
Application Rules
QOS Engine
Network Filter
Inbound Filter
Access Control
Website filter
Firewall Settings
Routing
Advanced Wireless
Wi-Fi Protected Setup
Advanced Network
Guest Zone
IPv6 Firewall
IPv6 Routing
D-Link DIR-819 User Manual
121
Section 4 - Connecting to a Wireless Network
Connect a Wireless Client to Your Router
WPS Button
The easiest and most secure way to connect your wireless devices to the router is with WPS (Wi-Fi Protected Setup). Most wireless
devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers, and cameras will have a WPS button
(or a software utility with WPS) that you can press to connect to the DIR-819 router. Please refer to your user manual for the
wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:
Step 1 - Press the WPS button on the DIR-819 for about 1 second. The wireless LED on the front will start to blink.
WPS Button
Step 2 - Within 2 minutes, press the WPS button on your wireless device (or launch the software utility and start the WPS
process).
Step 3 - Allow up to 1 minute for your connection to be configured. Once the WPS LED stops blinking, you will be connected
and your wireless connection will be secure with WPA2.
D-Link DIR-819 User Manual
122
Section 4 - Connecting to a Wireless Network
Windows® 10
When connecting to the DIR-819 wirelessly for the first time, you will need to input the wireless network name (SSID) and WiFi password (security key) of the device you are connecting to. If your product has a Wi-Fi configuration card, you can find the
default network name and Wi-Fi password here. Otherwise refer to the product label for the default Wi-Fi network SSID and
password, or enter the Wi-Fi credentials set during the product configuration.
To join an existing network, locate the wireless network icon in the taskbar,
next to the time display and click on it.
Wireless Icon
Clicking on this icon will display a list of wireless networks which are within
range of your computer. Select the desired network by clicking on the SSID.
D-Link DIR-819 User Manual
123
Section 4 - Connecting to a Wireless Network
To connect to the SSID, click Connect.
To automatically connect with the router when your device next detects the
SSID, click the Connect Automatically check box.
You will then be prompted to enter the Wi-Fi password (network security key)
for the wireless network. Enter the password into the box and click Next to
connect to the network. Your computer will now automatically connect to this
wireless network when it is detected.
You can also use Wi-Fi Protected Setup (WPS) to connect to the router. Press the
WPS button on your D-Link device and you will be automatically connected.
D-Link DIR-819 User Manual
124
Section 4 - Connecting to a Wireless Network
Windows® 8
WPA/WPA2
It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring
your wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used.
To join an existing network, locate the wireless network icon in the taskbar
next to the time display.
Wireless Icon
Clicking on this icon will display a list of wireless networks that are within
connecting proximity of your computer. Select the desired network by clicking
on the network name.
D-Link DIR-819 User Manual
125
Section 4 - Connecting to a Wireless Network
You will then be prompted to enter the network security key (Wi-Fi password)
for the wireless network. Enter the password into the box and click Next.
If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router, you
can also press the WPS button on your router during this step to enable the
WPS function.
When you have established a successful connection to a wireless network, the
word Connected will appear next to the name of the network to which you
are connected to.
D-Link DIR-819 User Manual
126
Section 4 - Connecting to a Wireless Network
Windows® 7
WPA/WPA2
It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring
your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Click on the wireless icon in your system tray (lower-right corner).
Wireless Icon
2. The utility will display any available wireless networks in your area.
D-Link DIR-819 User Manual
127
Section 4 - Connecting to a Wireless Network
3. Highlight the wireless connection with Wi-Fi name (SSID) you would
like to connect to and click the Connect button.
If you get a good signal but cannot access the Internet, check your TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
4. The following window appears while your computer tries to connect
to the router.
D-Link DIR-819 User Manual
128
Section 4 - Connecting to a Wireless Network
WPS
The WPS feature of the DIR-819 can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to
configure the WPS feature:
1. Click the Start button and select Computer from the Start menu.
2. Click Network on the left side.
D-Link DIR-819 User Manual
129
Section 4 - Connecting to a Wireless Network
3. Double-click the DIR-819.
DIR-819
4. Input the WPS PIN number (on the router label) in the Setup > Wireless
Setup menu in the Router’s Web UI) and click Next.
D-Link DIR-819 User Manual
130
Section 4 - Connecting to a Wireless Network
5. Type a name to identify the network.
6. To configure advanced settings, click the
icon.
Click Next to continue.
D-Link DIR-819 User Manual
131
Section 4 - Connecting to a Wireless Network
7. The following window appears while the DIR-819 is being configured.
Wait for the configuration to complete.
8. The following window informs you that WPS on the DIR-819 has been set
up successfully.
Make a note of the security key as you may need to provide this security key
if adding an older wireless device to the network in the future.
9. Click Close to complete WPS setup.
D-Link DIR-819 User Manual
132
Section 4 - Connecting to a Wireless Network
Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another company’s wireless utility, please refer to the
user manual of your wireless adapter for help connecting to a wireless network. Most wireless utilities will have a “site survey”
option similar to the Windows Vista® utility as seen below.
If you receive the Wireless Networks Detected bubble, click on the center of
the bubble to access the utility.
					or
Right-click on the wireless computer icon in your system tray (lower-right corner
next to the time). Select Connect to a network.
The utility will display any available wireless networks in your area. Click on a
network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check your TCP/IP
settings for your wireless adapter. Refer to the Networking Basics section in
this manual for more information.
D-Link DIR-819 User Manual
133
Section 4 - Connecting to a Wireless Network
WPA/WPA2
It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring
your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless
computer icon in your system tray (lower right corner of screen). Select
Connect to a network.
2. Highlight the Wi-Fi name (SSID) you would like to connect to and click
Connect.
D-Link DIR-819 User Manual
134
Section 4 - Connecting to a Wireless Network
3. Enter the same security key or passphrase (Wi-Fi password) that is on your
router and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the connection
fails, please verify that the security settings are correct. The key or passphrase
must be exactly the same as the one on the wireless router.
D-Link DIR-819 User Manual
135
Section 5 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DIR-819. Read the
following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different
operating system, the screenshots on your computer will look similar to these examples.
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.11.1 for example), you are not connecting to a website, nor do
you have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer
must be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
• Internet Explorer 10 or higher
• EDGE Browser 20 or higher
• Firefox 28 or higher
• Safari 6.0 or higher
• Chrome 28 or higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a
different cable, or connect to a different port on the device if possible. If the computer is turned off, the link light may not
be on.
• Disable any Internet security software running on the computer. Software firewalls such as ZoneAlarm, BlackICE, Sygate,
Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included
with your firewall software for more information on disabling or configuring it.
D-Link DIR-819 User Manual
136
Section 5 - Troubleshooting
• Configure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click
the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This
should open the login page for your web management.
• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30
seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. This process will change all your settings back to the factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip
to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30
seconds to access the router. The default IP address is 192.168.11.1. When logging in, leave the password box empty.
D-Link DIR-819 User Manual
137
Section 5 - Troubleshooting
3. Why can’t I connect to certain sites or send and receive emails when connecting through my router?
If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail,
we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be
another computer, or a URL.
• Click on Start and then click Run.
• Windows® 95, 98, and Me users type in command (Windows® NT, 2000, XP, Vista®, and 7 users type in cmd) and
press Enter (or click OK).
• Once the window opens, you’ll need to do a special ping. Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472
D-Link DIR-819 User Manual
138
Section 5 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented
packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the
proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Once you find your MTU, you can now configure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
• Open your browser, enter the IP address of your router (192.168.11.1) and click OK.
• Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page
for the device.
• Click on Setup and then click Manual Configure.
• To change the MTU, enter the number in the MTU field and click Save Settings to save your settings.
• Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments
of ten.
D-Link DIR-819 User Manual
139
Appendix A - Wireless Basics
Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless
connectivity within your home, business, or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link
wireless family of products will allow you to securely access the data you want, when, and where you want it. You will be able
to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead
of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee
shops and universities. Innovative ways to utilize WLAN technology are helping people work, and communicate more efficiently.
Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop
systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to
use servers, printers or an Internet connection supplied through the wired LAN. A wireless router is a device used to provide
this link.
D-Link DIR-819 User Manual
140
Appendix A - Wireless Basics
What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio
frequency to connect wirelessly so you have the freedom to connect computers anywhere in your home or office network.
Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link
delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.
How does wireless work?
Wireless works similarly to how cordless phones work, through radio signals that transmit data from one point A to point B.
But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range
area to be able to connect your computer. There are two different types of wireless networks: Wireless Local Area Network
(WLAN), and Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point
has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access
point the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places
like manufacturing plants, industrial locations, university and high school campuses, airports, golf courses, and many other
outdoor venues.
Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to
30 feet away.
D-Link DIR-819 User Manual
141
Appendix A - Wireless Basics
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as
much power. This makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other
devices that operate on batteries.
Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business,
D-Link has a wireless solution for it.
Home Uses/Benefits
• Gives everyone at home broadband access
• Surf the web, check email, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Office and Home Office Uses/Benefits
• Stay on top of everything at home as you would at office
• Remotely access your office network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate office space
Where is wireless used?
Wireless technology is expanding everywhere, not just at home or office. People like the freedom of mobility and it’s becoming
so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public
places is usually called “hotspots”.
Using a D-Link USB adapter with your laptop, you can access the hotspot to connect to the Internet from remote locations like:
airports, hotels, coffee shops, libraries, restaurants, and convention centers.
D-Link DIR-819 User Manual
142
Appendix A - Wireless Basics
Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start.
That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your router or access point
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to
place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have
a two-story home, you may need a repeater to boost the signal to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access
point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency.
Security
Don’t let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on
the WPA or WEP security feature on the router. Refer to the product manual for detail information on how to set it up.
D-Link DIR-819 User Manual
143
Appendix A - Wireless Basics
Wireless Modes
There are basically two modes of networking:
• Infrastructure – All wireless clients will connect to an access point or wireless router.
• Ad-hoc – Directly connecting to another computer for peer-to-peer communication using wireless network
adapters on each computer, such as two or more wireless network USB adapters.
An Infrastructure network contains an access point or wireless router. All the wireless devices, or clients, will connect to the
wireless router or access point.
An Ad-hoc network contains only clients, such as laptops with wireless USB adapters. All the adapters must be in Ad-hoc mode
to communicate.
D-Link DIR-819 User Manual
144
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP
server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.)
At the prompt, type ipconfig and press Enter.
This will display the IP address, subnet mask, and the
default gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation,
security settings, and the settings on your router.
Some firewall software programs may block a DHCP
request on newly installed adapters.
D-Link DIR-819 User Manual
145
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® 7 -		
Windows Vista® Windows® XP Windows® 2000 -
Click on Start > Control Panel > Network and Internet > Network and Sharing Center.
Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.
Click on Start > Control Panel > Network Connections.
From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet as your network
or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.11.1, make your IP address 192.168.0.X where X is a
number between 2 and 99. Make sure that the number you choose is not in use on the network. Set
the Default Gateway the same as the LAN IP address of your router (I.E. 192.168.11.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.11.1). The Secondary DNS is
not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
D-Link DIR-819 User Manual
146
Appendix B - Networking Basics
Wireless Security
This section will show you the different levels of security you can use to protect your data from intruders. The DIR-819 offers
the following types of security:
• WPA2 (Wi-Fi Protected Access 2) 			
• WPA (Wi-Fi Protected Access)				
• WPA2-PSK (Pre-Shared Key)
• WPA-PSK (Pre-Shared Key)
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing
algorithm and by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based
on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP
regulates access to a wireless network based on a computer’s hardware-specific MAC address, which is relatively simple
to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized
network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between
8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your
wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public
key encryption system to ensure that only authorized network users can access the network.
D-Link DIR-819 User Manual
147
Appendix C - Technical Specifications
Technical Specifications
Device Interfaces
• 802.11 ac/n/g/a/b wireless LAN
• Four 10/100 Fast Ethernet LAN ports
• One 10/100 Fast Ethernet WAN port
Antenna Types
• Three external antennas
Standards
• IEEE 802.11ac1,2,3
• IEEE 802.11n
• IEEE 802.11g
• IEEE 802.11b
• IEEE 802.11a
• IEEE 802.3
• IEEE 802.3u
Security
• WPA™ - Personal/Enterprise
• WPA2™ - Personal/Enterprise
• Wi-Fi Protected Setup (WPS) PIN/PBC
Power
• Input: 100 to 240 V AC, 50/60 Hz
• Output: 12 V DC, 0.5 A
Operating Temperature
• 0 to 40 °C (32 to 104 °F)
Storage Temperature
• -20 to 65 °C (-4 to 149 °F)
Operating Humidity
• 10% to 95% maximum (non-condensing)
Storage Humidity
• 5% to 95% maximum (non-condensing)
Certifications
• FCC
• ISED
• UL
• Wi-Fi Certified
• Wi-Fi Protected Setup (WPS)
Dimensions & Weight
• L = 192 mm (7.56 inches)
• W = 108 mm (4.25 inches)
• H = 30 mm (1.8 inches)
• 240 g (8.5 ounces)
1 Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, 802.11n, and 802.11ac specifications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range.
2 Frequency Range varies depending on country’s regulation.
3 The DIR-819 does not include 5.47-5.725 GHz in some regions.
D-Link DIR-819 User Manual
148
Appendix D - Regulatory Statements
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Non-modifications Statement:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance
with FCC multi-transmitter product procedures. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection
of other channels is not possible.
Note
The country code selection is for non-USA models only and is not available to all USA models. Per FCC regulations, all WiFi product marketed in
the USA must be fixed to USA operational channels only.
D-Link DIR-819 User Manual
149
Appendix D - Regulatory Statements
RF Frequency Requirements
This device is for indoor use only when using all channels in the 5.125 to 5.250 GHz frequency range. High power radars are allocated as primary
users of the 5.725 to 5.850 GHz bands. These radar stations can cause interference with and/or damage this device.
It is restricted to indoor environments only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
D-Link DIR-819 User Manual
150
Appendix D - Regulatory Statements
Innovation, Science and Economic Development Canada (ISED) Statement:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development Canada (ISED) Statement:
This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems;
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques
de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate;
(iii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5850
MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et l'exploitation non point à point, selon le cas;
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement
doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
D-Link DIR-819 User Manual
151

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42
Create Date                     : 2016:11:04 10:32+08:00
Metadata Date                   : 2016:11:04 10:33:19+08:00
Modify Date                     : 2016:11:04 10:33:19+08:00
Creator Tool                    : Adobe InDesign CC 2017 (Windows)
Instance ID                     : uuid:21b67f0e-c7e1-4d85-acf1-577589ab53b8
Original Document ID            : adobe:docid:indd:51a62a94-6654-11de-a441-985dc935f5ab
Document ID                     : xmp.id:d38cfc2a-61d4-1443-81a9-710d371f4be1
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:b55ff922-590a-dd4a-bb06-9b5dd532d649
Derived From Document ID        : xmp.did:3F040550AAA1E611A41D983BDD04DA2B
Derived From Original Document ID: adobe:docid:indd:51a62a94-6654-11de-a441-985dc935f5ab
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Windows)
History Changed                 : /
History When                    : 2016:11:04 10:32+08:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 155
Creator                         : Adobe InDesign CC 2017 (Windows)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: KA2IR819A1

Navigation menu