D Link IR860LA1 Wireless AC1200 Dual Band Gigabit Router USB 3.0 User Manual DIR 860L A1 Manual 20130125 ok

D Link Corporation Wireless AC1200 Dual Band Gigabit Router USB 3.0 DIR 860L A1 Manual 20130125 ok

user manual

Version 1.0 | 01/15/2013
User Manual
DIR-860L
Wireless AC1200 Dual-Band Gigabit
Cloud Router USB 3.0
iD-Link DIR-860L User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes.
Manual Revisions
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of
their respective companies.
Copyright © 2013 by D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Corporation.
Revision Date Description
1.0 January 15, 2013 t*OJUJBMSFMFBTF
Preface
iiD-Link DIR-860L User Manual
Table of Contents
Preface ................................................................................. i
Manual Revisions ........................................................................... i
Trademarks ...................................................................................... i
Product Overview .............................................................. 1
Package Contents ......................................................................... 1
System Requirements ................................................................. 2
Introduction ................................................................................... 3
Features ............................................................................................ 4
Hardware Overview ..................................................................... 5
Connections ........................................................................... 5
LEDs ........................................................................................... 6
Installation ......................................................................... 7
Before you Begin ........................................................................... 7
Wireless Installation Considerations ...................................... 8
Manual Setup ................................................................................. 9
Conguration ...................................................................11
D-Link Quick Setup Wizard .....................................................12
QRS Mobile App (iOS, Android) .............................................19
SharePort Mobile App (iOS, Android) .................................20
Web-based Conguration Utility ..........................................24
Internet Connection Setup .............................................25
Static IP ..............................................................................26
Dynamic IP (DHCP) ........................................................27
PPPoE (Username/Password) ....................................28
PPTP ....................................................................................30
L2TP ....................................................................................31
DS-Lite ...............................................................................33
Wireless Settings .................................................................34
Wireless Connection Setup Wizard..........................35
Add Wireless Device with WPS Wizard ...................38
Manual Wireless Settings .................................................40
802.11ac draft (2.4GHz) ...............................................40
802.11ac draft (5GHz) ...................................................41
Network Settings ................................................................42
Router Settings ...............................................................43
DHCP Server Settings ...................................................44
DHCP Reservation .........................................................45
Storage ...................................................................................46
Media Server.........................................................................47
IPv6 ..........................................................................................48
IPv6 Internet Connection Setup Wizard ................49
Manual IPv6 Local Connectivity Setup ..................54
IPv6 Manual Setup.........................................................55
mydlink Settings .................................................................66
Advanced ......................................................................................67
Virtual Server ........................................................................67
Port Forwarding ..................................................................68
Application Rules ................................................................69
QoS Engine............................................................................70
Network Filters .....................................................................72
Access Control .....................................................................73
Website Filters ......................................................................76
Table of Contents
iiiD-Link DIR-860L User Manual
Table of Contents
Inbound Filter ......................................................................77
Firewall Settings ..................................................................78
Routing ...................................................................................80
Advanced Wireless .............................................................81
Wi-Fi Protected Setup .......................................................82
Advanced Network ............................................................84
Guest Zone ............................................................................85
IPv6 Firewall ..........................................................................86
IPv6 Routing .........................................................................87
Tools ................................................................................................88
Admin .....................................................................................88
Time .........................................................................................89
SysLog ..................................................................................... 90
Email Settings ......................................................................91
System ....................................................................................92
Firmware ................................................................................93
Firmware Upgrade .........................................................93
Language Pack ................................................................93
Dynamic DNS .......................................................................94
System Check .......................................................................95
Schedules ..............................................................................96
Status ..............................................................................................97
Device Info ............................................................................97
Logs .........................................................................................98
Statistics .................................................................................99
Internet Sessions .............................................................. 100
Wireless ............................................................................... 101
Routing ................................................................................ 102
IPv6 ....................................................................................... 103
IPv6 Routing ...................................................................... 104
Support ....................................................................................... 105
Connect a Wireless Client to your Router ....................106
WPS Button ................................................................................ 106
Windows® 7 ................................................................................ 107
WPA/WPA2 ......................................................................... 107
WPS ....................................................................................... 110
Windows Vista® ......................................................................... 114
WPA/WPA2 ......................................................................... 115
WPS/WCN 2.0 .................................................................... 117
Windows® XP ............................................................................. 118
WPA/WPA2 ......................................................................... 119
Troubleshooting ............................................................121
Wireless Basics ...............................................................125
What is Wireless? ...................................................................... 126
Tips ................................................................................................ 128
Wireless Modes ......................................................................... 129
Networking Basics .........................................................130
Check your IP address ............................................................ 130
Statically Assign an IP address ............................................ 131
Wireless Security ......................................................... 132
What is WPA? ................................................................ 132
Technical Specications ................................................133
1D-Link DIR-860L User Manual
Section 1 - Product Overview
Product Overview
Package Contents
Note: Using a power supply with a dierent voltage rating than the one included with the DIR-860L will cause damage and void the warranty
for this product.
If any of the above items are missing, please contact your reseller.
DIR-860L Wireless AC1200 Dual-Band Gigabit Cloud Router USB 3.0
Ethernet Cable
Power Adapter
Wi-Fi Conguration Note
Wi-Fi Conguration Note
2D-Link DIR-860L User Manual
Section 1 - Product Overview
Network Requirements
t"O&UIFSOFUCBTFE$BCMFPS%4-NPEFN
t"OBDESBGUOHCPSBXJSFMFTTBEBQUPSPSBO&UIFSOFU
port
Web-based Conguration
Utility Requirements
Computer with the following:
t8JOEPXT¥.BDJOUPTIPS-JOVYCBTFEPQFSBUJOHTZTUFN
t"OJOTUBMMFE&UIFSOFUBEBQUFS
Browser Requirements:
t*OUFSOFU&YQMPSFSPSIJHIFS
t'JSFGPYPSIJHIFS
t4BGBSJPSIJHIFS
t$ISPNFPSIJHIFS
Windows® Users: Make sure you have the latest version of Java
installed. Visit www.java.com to download the latest version.
mydlink Requirements
tJ1IPOFJ1BEJ1PE5PVDIJ04PSIJHIFS
t"OESPJEEFWJDFPSIJHIFS
t$PNQVUFSXJUIUIFGPMMPXJOHCSPXTFSSFRVJSFNFOUT
t*OUFSOFU&YQMPSFSPSIJHIFS
t'JSFGPYPSIJHIFS
t4BGBSJPSIJHIFS
t$ISPNFPSIJHIFS
iPhone, iPad, and iPod touch are registered trademarks of Apple Inc. Android is a trademark of Google, Inc.
System Requirements
3D-Link DIR-860L User Manual
Section 1 - Product Overview
Introduction
The D-Link Wireless AC1200 Dual-Band Gigabit Cloud Router USB 3.0 (DIR-860L) comes equipped with four Gigabit ports to
provide speeds up to 10x faster than standard 10/100 ports. It also uses 802.11ac (draft) technology with multiple intelligent
antennas to maximize the speed and range of your wireless signal and signicantly outperform 802.11n devices. With the
addition of Intelligent Quality of Service (QoS), data streams are separated, helping to organize and prioritize your network
trac so that your video streaming, gaming, and VoIP calls run smoother over both your wired and wireless network.
The DIR-860L supports a host of cloud features including QRS Mobile, which allows you to set up and congure the router
using a mobile app. You can set up your router right from your sofa, no PC required.
The Wireless AC1200 Dual-Band Gigabit Cloud Router USB 3.0 is also mydlink-enabled, which gives you access to your home
network no matter where you are. Now you can monitor and manage your home network right from your laptop, iPhone®,
iPad®, or Android™ device. mydlink-enabled routers can be congured to send an email to keep you informed anywhere,
anytime when new devices are connecting to your network or unwanted access is detected. Monitor in real-time websites that
are being visited with recent browser history displayed on the mydlink™ Lite app – great for parents.
SharePort Mobile technology lets you take advantage of the USB 3.0 port found on the back of your DIR-860L. Plug in a USB
storage drive and you can use the SharePort Mobile app for iOS and Android to access les, stream videos, view photos, or
listen to music on your laptop or mobile devices. Plug in a printer and you can use the SharePort Mobile Plus app to share that
printer with all of your devices.
The DIR-860L Wireless AC1200 Dual-Band Gigabit Cloud Router USB 3.0 provides incredible speeds, smart antenna technology,
fast ports, cloud features, and terric security features. It also features an innovative design and easy installation options.
4D-Link DIR-860L User Manual
Section 1 - Product Overview
t'BTUFS8JSFMFTT/FUXPSLJOH - The DIR-860L can provide up to a full 1750Mbps* wireless connection with
concurrent 801.11ac and 802.11n wireless clients . It also operates on both the 2.4 GHz and 5 GHz bands, to
allow separation of trac so users can participate in high-bandwidth activities, such as video streaming, online
gaming, and real-time audio, without aecting low-priority trac like email and web surng.
t$MPVE'FBUVSFT - The DIR-860L support the QRS Mobile app to setup the router using a mobile device. It is also
mydlink-enabled so you can remotely access and mange your DIR-860L from a mobile device. SharePort Mobile
can be used to share les, stream videos, view photos, and play music. SharePort Plus lets you share a printer.
t$PNQBUJCMFXJUIBCHO%FWJDFT - The DIR-860L is still fully compatible with the 802.11n, IEEE 802.11g
and 802.11a standards, so it can connect with existing 802.11n, 802.11g, 802.11b, and 802.11a wireless devices.
t"EWBODFE'JSFXBMM'FBUVSFT - The Web-based user interface displays a number of advanced network
NBOBHFNFOUGFBUVSFTJODMVEJOH
tContent Filtering - Easily applied content ltering based on MAC Address, URL, and/or Domain
Name.
tFilter Scheduling - These lters can be scheduled to be active on certain days or for a duration of
hours or minutes.
t4FDVSF.VMUJQMF$PODVSSFOU4FTTJPOT - The DIR-860L can pass through VPN sessions. It supports
multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-860L can securely access
corporate networks.
t6TFSGSJFOEMZ4FUVQ8J[BSE - Through its easy-to-use Web-based user interface, the DIR-860L lets you control
what information is accessible to those on the wireless network, whether from the Internet or from your company’s
server. Congure your router to your specic settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11b, 802.11g, 802.11n, and draft 802.11ac specications. Actual data throughput will vary. Network
conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead lower actual data throughput rate.
Environmental conditions will adversely aect wireless signal range.
Features
5D-Link DIR-860L User Manual
Section 1 - Product Overview
Hardware Overview
Connections
1USB 3.0 Port Connect a USB ash drive to share content , or connect it to a USB printer to share it on your network.
2WPS Button Press to start the WPS process and automatically create a secure connection to a WPS client.
3Gigabit LAN Ports (1-4) Connect Ethernet devices such as computers, switches, storage (NAS) devices and game consoles.
4Gigabit Internet Port Using an Ethernet cable, connect your broadband modem to this port.
5Power Button Press the power button to power on and o.
6Power Receptor Receptor for the supplied power adapter.
7Reset Button Insert a paperclip in to the hole and hold for several seconds to reset the router to default settings.
4
5
6
2
1
3
7
6D-Link DIR-860L User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
1Power LED A solid green light indicates a proper connection to the power supply. The light will blink green during
the WPS process. The light will be a solid orange during boot up.
2Internet LED A solid light indicates connection on the Internet port. If the LED is orange, the connection is good but
the router cannot connect to the Internet.
1
2
7D-Link DIR-860L User Manual
Section 2 - Installation
Before you Begin
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the router
in an enclosed area such as a closet or cabinet, or in an attic or garage.
t 1MFBTFDPOöHVSFUIFSPVUFSXJUIUIFDPNQVUFSUIBUXBTMBTUDPOOFDUFEEJSFDUMZUPZPVSNPEFN
t :PVDBOPOMZVTFUIF&UIFSOFUQPSUPOZPVSNPEFN*GZPVXFSFVTJOHB64#DPOOFDUJPOCFGPSFVTJOHUIFSPVUFS
then you must turn o your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port
on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection
types (USB to Ethernet).
t *GZPVIBWF%4-BOEBSFDPOOFDUJOHWJB111P&NBLFTVSFZPVEJTBCMFPSVOJOTUBMMBOZ111P&TPGUXBSFTVDIBT8JO1PFU
Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.
8D-Link DIR-860L User Manual
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the
operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings,
or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types
of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to
GPMMPXUIFTFCBTJDHVJEFMJOFT
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum -
each wall or ceiling can reduce your device’s range from 3-90 feet (1-30 meters.) Position your devices so that
the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree
angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it appears over 42 feet (14 meters) thick!
Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better
reception.
3. Building Materials make a dierence. A solid `metal door or aluminum studs may have a negative eect on range.
Try to position access points, wireless routers, and computers so that the signal passes through drywall or open
doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le
cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF
noise.
5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security
systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone
base is as far away from your wireless devices as possible. The base transmits a signal even if the phone is in not
in use.
9D-Link DIR-860L User Manual
Section 2 - Installation
1. Turn o and unplug your cable or DSL broadband modem. This is required.
Manual Setup
4
2. Position your router close to your modem and a computer. Place the router in an open area of your intended
work area for better wireless coverage.
3. Unplug the Ethernet cable from your modem (or existing router if upgrading) that is connected to your computer.
Plug it into the LAN port labeled 1 on the back of your router. The router is now connected to your computer.
Modem
DIR-860LComputer
10D-Link DIR-860L User Manual
Section 2 - Installation
4. Plug one end of the included Ethernet cable that came with your router into the yellow port labeled INTERNET
on the back of the router. Plug the other end of this cable into the Ethernet port on your modem.
5. Reconnect the power adapter to your cable or DSL broadband modem and wait for two minutes.
6. Connect the supplied power adapter into the power receptor on the back of the router and then plug it into a
power outlet or surge protector. Press the power button and verify that the power LED is lit. Allow 1 minute for
the router to boot up.
1
7. If you are connecting to a Broadband service, you may be online already and further conguration will be optional.
DIR-860L
DIR-860L
Modem
Computer
Modem
Computer
11D-Link DIR-860L User Manual
Section 2 - Installation
5IFSFBSFTFWFSBMEJòFSFOUXBZTZPVDBODPOöHVSFZPVSSPVUFSUPDPOOFDUUPUIF*OUFSOFUBOEDPOOFDUUPZPVSDMJFOUT
t %-JOL4FUVQ8J[BSE - This wizard will launch when you log into the router for the rst time. Refer to page 12.
t 234.PCJMF"QQ- Use your iPhone, iPad, or iPod Touch to congure your router. Refer to page 19.
t Manual Setup - Log into the router and manually congure your router (advanced users only). Refer to pagepage 26.
Conguration
12D-Link DIR-860L User Manual
Section 3 - Conguration
This wizard is designed to guide you through a step-by-step
process to congure your new D-Link router and connect to the
Internet.
Click Next to continue.
D-Link Quick Setup Wizard
If this is your rst time installing the router, open your web browser. You
will automatically be directed to the Wizard Setup Screen.
If the wizard does not open automatically, you can alternatively reach
the conguration utility by entering “http://dlinkrouter.local.” or the
IP address of the router (IUUQ). Please refer to page 24.
Please wait while your router detects your internet connection type.
If the router detects your Internet connection, you may need to enter
your ISP information such as username and password.
13D-Link DIR-860L User Manual
Section 3 - Conguration
If the router does not detect a valid Ethernet connection from the
Internet port, this screen will appear. Connect your broadband modem
to the Internet port and then click 5SZ"HBJO.
If the router detects an Ethernet connection but does not detect the type
of Internet connection you have, this screen will appear. Click Guide me
through the Internet Connection Settings to display a list of connection
types to choose from.
Select your Internet connection type and click Next to continue.
14D-Link DIR-860L User Manual
Section 3 - Conguration
If the router detected or you selected PPPoE, enter your PPPoE username
and password and click Next to continue.
Note: Make sure to remove any PPPoE software from your computer. The
software is no longer needed and will not work through a router.
If the router detected or you selected PPTP, enter your PPTP username,
password, and other information supplied by your ISP. Click Next to
continue.
If the router detected or you selected L2TP, enter your L2TP username,
password, and other information supplied by your ISP. Click Next to
continue.
15D-Link DIR-860L User Manual
Section 3 - Conguration
If the router detected or you selected Static, enter the IP and DNS
settings supplied by your ISP. Click Next to continue.
For both the 2.4GHz and 5GHz segments, create a Wi-Fi network name
(SSID) using up to 32 characters.
Create a Wi-Fi password (between 8-63 characters). Your wireless clients
will need to have this passphrase or key entered to be able to connect
to your wireless network.
Click Next to continue.
In order to secure your router, please enter a new password to use when
accessing the web-based conguration utility (where the password eld
was previously left blank). Check the &OBCMF(SBQIJDBM"VUIFOUJDBUJPO
box to enable CAPTCHA authentication for added security. Be sure to
make a record of this password for future use. Click Next to continue.
16D-Link DIR-860L User Manual
Section 3 - Conguration
Select your time zone from the drop-down menu and click Next to
continue.
The Setup Complete window will display your Wi-Fi settings. Click Save
and Connect to continue.
If you want to create a bookmark to the router, click OK. Click Cancel if
you do not want to create a bookmark.
If you clicked Yes, a window may appear (depending on what web
browser you are using) to create a bookmark.
17D-Link DIR-860L User Manual
Section 2 - Installation
To use the mydlink service (mydlink.com or the mydlink Lite app), you
must have an account. Select if you do have a mydlink account or if you
need to create one. Click Next to continue.
If you do not want to register at this time, click Cancel.
If you selected Yes , enter your mydlink account name (email address)
and password. Click Login to register your router.
If you selected No, ll out the requested information and click Next to
create your mydlink account.
18D-Link DIR-860L User Manual
Section 3 - Conguration
The mydlink App will allow you to receive notices, browse network
users, and congure your router from an iPhone/iPad/iPod Touch
(iOS 3.0 or higher), or Android device (1.6 or higher).
To download the "mydlink Lite" app, visit the App Store, Google Play,
or IUUQNZEMJOLDPN-JUF.
PC and Mac users can use the mydlink portal at IUUQNZEMJOLDPN.
19D-Link DIR-860L User Manual
Section 3 - Conguration
QRS Mobile App (iOS, Android)
D-Link oers an app for your iOS or Android device to install and congure your router.
Step 1
From an iOS device, go to the App Store. From an Android
device go to Google Play. Search for ‘D-Link’, select QRS Mobile,
and download the app to your device. You may also scan the
appropriate code on the right to locate the app download page.
Step 2
Once your app is installed, you may now congure your router.
Connect to the router wirelessly by going to your wireless utility
on your device. Scan for the Wi-Fi name (SSID) as listed on the
supplied info card. Select and then enter your Wi-Fi password.
Step 3
Once you connect to the router, launch the QRS mobile app and
it will guide you through the installation of your router.
iOS Android
20D-Link DIR-860L User Manual
Section 3 - Conguration
2. Use your iOS or Android mobile device to scan the QR code
to the right to download the SharePort Mobile app.
You can also search for the SharePort Mobile app directly in
the iOS App Store or Google Play.
SharePort Mobile App (iOS, Android)
3. From your iOS or Android mobile device, choose Settings.
Note: These steps are for the iOS version of the
app. The Android version may dier slightly. Settings
iOS Android
USB port
1. Plug your USB storage drive into the USB port.
Note: The DIR-860L supports hard drives with up to
one terabyte of storage capacity.
The SharePort Mobile app will allow you to access les from a USB storage drive that is plugged into your router. You must enable le sharing from
the Setup > Storage page (refer to page 22) for this app to work properly.
21D-Link DIR-860L User Manual
Section 3 - Conguration
4. Click Wi-Fi, select the Wi-Fi Network Name (SSID) that you created during
setup and then enter the default Wi-Fi password located on your Wi-Fi
conguration note.
6. The following screen will appear.
5. Once connected, tap on the SharePort Mobile icon.
22D-Link DIR-860L User Manual
Section 3 - Conguration
7. Tap on the Settings icon located on the right top corner of the screen.
Tap Edit to enter your User Name and Password (the default username
is admin and the password eld should be left blank). Once you nish,
click Done to continue.
9. For the Music section, click the music icon to play your music from your
USB ash drive.
8. For the Movie section, click the movie icon to play your movie from your
USB ash drive.
23D-Link DIR-860L User Manual
Section 3 - Conguration
10. For the Photo section, click the Photo icon to view your photos from
your USB ash drive.
11. For the Files section, click on the Files icon to view your les from your
USB ash drive.
12. For the Folder section, click the folder icon to view your folders
from your USB ash drive.
24D-Link DIR-860L User Manual
Section 3 - Conguration
Web-based Conguration Utility
Enter your password. The password should be left blank
by default.
To access the conguration utility, open a web-browser such as
Internet Explorer and enter IUUQEMJOLSPVUFSMPDBM
Users may also connect by typing the IP address of the router
(IUUQ) in the address bar.
25D-Link DIR-860L User Manual
Section 3 - Conguration
Internet Connection Setup
If you want to congure your router to connect to the Internet
using the wizard, click *OUFSOFU$POOFDUJPO4FUVQ8J[BSE.
You will be directed to the Quick Setup Wizard. Please refer
to page 12.
Click Manual Internet Connection Setup to congure your
connection manually and continue to the next page.
26D-Link DIR-860L User Manual
Section 3 - Conguration
Select Static IP to manually enter the IP settings supplied by your ISP.
Advanced Domain Name System (DNS) services enhances your Internet
performance by getting you the information and web pages you are
looking for faster and more reliably. In addition, it improves your overall
Internet experience by correcting many common typing mistakes
automatically, taking you where you intended to go and saving you
valuable time.
Check to enable true Gigabit routing. This will increase the throughput
of the WAN-LAN connectivity of the router.
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The DNS server information will be supplied by your ISP
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1500 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the $MPOF:PVS1$T."$"EESFTT button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
My Internet
Connection Is:
Enable Advanced
DNS Service:
Enable True
Gigabit Routing
Connectivity:
IP Address:
Subnet Mask:
Default Gateway:
DNS Servers:
MTU:
MAC Address:
Manual Internet Setup
Static IP
Select your connection type from the My Internet Connect Is drop-down box. Choose Static IP if all of the necessary IP information has been provided
by your ISP. You will need to enter the IP address, subnet mask, gateway address, and DNS address(es). Each IP address entered in the elds must
be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
27D-Link DIR-860L User Manual
Section 3 - Conguration
Select Dynamic IP (DHCP) to obtain IP Address information automatically
from your ISP. Select this option if your ISP does not give you any IP
numbers to use. This option is commonly used for cable modem services.
Advanced Domain Name System (DNS) services enhances your Internet
performance by getting you the information and web pages you are looking
for faster and more reliably. In addition, it improves your overall Internet
experience by correcting many common typing mistakes automatically,
taking you where you intended to go and saving you valuable time.
Disclaimer%-JOLNBLFT OPXBSSBOUZBT UPUIFBWBJMBCJMJUZSFMJBCJMJUZ
functionality and operation of the Advanced DNS service or its features.
Check to enable true Gigabit routing. This will increase the throughput
of the WAN-LAN connectivity of the router.
The Host Name is optional but may be required by some ISPs. Leave
blank if you are not sure.
Check the box if you are having problems obtaining an IP address from
your ISP.
Enter the Primary and secondary DNS server IP addresses assigned by your ISP. These addresses are usually obtained automatically
from your ISP. Leave at 0.0.0.0 if you did not specically receive these from your ISP.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1500 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the $MPOF:PVS1$T."$"EESFTT button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
My Internet
Connection:
Enable Advanced
DNS Service:
Enable True
Gigabit Routing
Connectivity:
Host Name:
Use Unicasting:
Primary/Secondary
DNS Server:
MTU:
MAC Address:
Dynamic IP (DHCP)
If you are unsure what method you use to connect to the Internet, try this rst. Cable modems usually use this type of connection
28D-Link DIR-860L User Manual
Section 3 - Conguration
Select 111P&6TFSOBNF1BTTXPSE from the drop-down menu.
Advanced Domain Name System (DNS) services enhances your Internet
performance by getting you the information and web pages you are
looking for faster and more reliably. In addition, it improves your overall
Internet experience by correcting many common typing mistakes
automatically, taking you where you intended to go and saving you
valuable time.
Disclaimer%-JOLNBLFT OPXBSSBOUZBT UPUIFBWBJMBCJMJUZSFMJBCJMJUZ
functionality and operation of the Advanced DNS service or its features.
Check to enable true Gigabit routing. This will increase the throughput
of the WAN-LAN connectivity of the router.
Select Static IP if your ISP assigned you IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next box.
Enter the ISP Service Name (optional).
Select either "MXBZTPO, On-Demand, or Manual.
My Internet
Connection:
Enable
Advanced DNS
Service:
Enable True
Gigabit Routing
Connectivity:
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnect
Mode:
PPPoE (Username/Password)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password.
This option is typically used for DSL services. Make sure to remove any PPPoE software from your computer. The software is not needed and will
not work through a router.
29D-Link DIR-860L User Manual
Section 3 - Conguration
Maximum
Idle Time:
DNS
Addresses:
MTU:
MAC Address:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the $MPOF:PVS1$T."$"EESFTT button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
30D-Link DIR-860L User Manual
Section 3 - Conguration
Select 11516TFSOBNF1BTTXPSE from the drop-down menu.
Advanced Domain Name System (DNS) services enhances your Internet
performance by getting you the information and web pages you are
looking for faster and more reliably. In addition, it improves your overall
Internet experience by correcting many common typing mistakes
automatically, taking you where you intended to go and saving you
valuable time.
Disclaimer%-JOLNBLFT OPXBSSBOUZBT UPUIFBWBJMBCJMJUZSFMJBCJMJUZ
functionality and operation of the Advanced DNS service or its features.
Check to enable true Gigabit routing. This will increase the throughput of
the WAN-LAN connectivity of the router.
Select Static if your ISP assigned you an IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses (Static PPTP
only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password in the next box.
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This
option is typically used for DSL services.
My Internet
Connection:
Enable Advanced
DNS Service:
Enable True
Gigabit Routing
Connectivity:
Address Mode:
PPTP IP Address:
PPTP Subnet Mask:
PPTP Gateway:
PPTP Server IP:
Username:
Password:
Reconnect Mode:
31D-Link DIR-860L User Manual
Section 3 - Conguration
Select -516TFSOBNF1BTTXPSE from the drop-down menu.
Advanced Domain Name System (DNS) services enhances your Internet
performance by getting you the information and web pages you are
looking for faster and more reliably. In addition, it improves your overall
Internet experience by correcting many common typing mistakes
automatically, taking you where you intended to go and saving you
valuable time.
Disclaimer%-JOLNBLFT OPXBSSBOUZBT UPUIFBWBJMBCJMJUZSFMJBCJMJUZ
functionality and operation of the Advanced DNS service or its features.
Check to enable true Gigabit routing. This will increase the throughput of
the WAN-LAN connectivity of the router.
Select Static if your ISP assigned you an IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses (Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password in the next box.
Select either "MXBZTPO, On-Demand, or Manual.
L2TP
Choose L2TP (Layer 2 Tunneling Protocol ) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option
is typically used for DSL services.
My Internet
Connection:
Enable Advanced
DNS Service:
Enable True
Gigabit Routing
Connectivity:
Address Mode:
PPTP IP Address:
PPTP Subnet Mask:
PPTP Gateway:
PPTP Server IP:
Username:
Password:
Reconnect Mode:
32D-Link DIR-860L User Manual
Section 3 - Conguration
Select either "MXBZTPO, On-Demand, or Manual.
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
The DNS server information will be supplied by your ISP.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1400 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the $MPOF:PVS1$T."$"EESFTT button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Maximum Idle
Time:
DNS Servers:
MTU:
MAC Address:
33D-Link DIR-860L User Manual
Section 3 - Conguration
DS-Lite
%4-JUFJTBO*1WDPOOFDUJPOUZQF"GUFSTFMFDUJOH%4-JUFUIFGPMMPXJOHQBSBNFUFSTXJMMCFBWBJMBCMFGPSDPOöHVSBUJPO
DS-Lite
Conguration:
AFTR IPv6 Address:
B4 IPv4 Address:
WAN IPv6 Address:
IPv6 WAN Default
Gateway:
Select the DS-Lite DHCPv6 option to let the router allocate the AFTR
IPv6 address automatically. Select the Manual Conguration to enter
the AFTR IPv6 address in manually.
After selecting the Manual Conguration option above, enter the AFTR
IPv6 address used here.
Enter the B4 IPv4 address value used here.
Once connected, the WAN IPv6 address will be displayed here.
Once connected, the IPv6 WAN Default Gateway address will be
displayed here.
34D-Link DIR-860L User Manual
Section 3 - Conguration
Wireless Settings
If you want to congure the wireless settings on your router using the wizard,
click 8JSFMFTT/FUXPSL4FUVQ8J[BSEand refer to page 42.
Click "EE8JSFMFTT%FWJDFXJUI814 if you want to add a wireless device
using Wi-Fi Protected Setup (WPS) and refer to page 44.
If you want to manually congure the wireless settings on your router click
Manual Wireless Network Setup and refer to the next page.
35D-Link DIR-860L User Manual
Section 4 - Security
Wireless Connection Setup Wizard
To run the security wizard, click on Setup at the top and then click Wireless
$POOFDUJPO4FUVQ8J[BSE.
STEP 1: Type your desired wireless network names (SSIDs) for both the 2.4 GHz
band and the 5 GHz band.
"VUPNBUJDBMMZSelect this option to automatically generate the router’s
network key (password) and click Next.
Manually: Select this option to manually enter your network key and
click Next.
36D-Link DIR-860L User Manual
Section 4 - Security
If you selected "VUPNBUJDBMMZ, the wizard will generate a pre-shared key
(password). The password will be the same for both the 2.4GHz and 5GHz
bands.
Click Next.
You will now see a summary window that displays your settings. Write down
the password and use it to access your wireless networks.
Click Save to save your settings.
37D-Link DIR-860L User Manual
Section 4 - Security
If you selected Manually, the option to make your password the same on
both bands will be oered.
Enter your wireless password in the box below. If you chose to have dierent
passwords for each band, you will need to enter a separate password for
each band.
Click Next.
You will now see a summary window that displays your settings. Write down
the password and use it to access your wireless networks.
Click Save to save your settings.
38D-Link DIR-860L User Manual
Section 4 - Security
From the Setup > Wireless Settings screen, click "EE8JSFMFTT%FWJDFXJUI
WPS.
Add Wireless Device with WPS Wizard
If you select Manual, a settings summary screen will appear. Write down the
security key and use this to access your wireless networks.
Click OK to nish.
Select "VUP to add a wireless client using WPS (Wi-Fi Protected Setup) and
then click
Next. Skip to the next page.
If you are unfamiliar with the types of wireless security, more information is located in the appendix at back of this manual.
39D-Link DIR-860L User Manual
Section 4 - Security
PIN: Select this option to use PIN method. In order to use this method you
must know the wireless client’s 8 digit PIN and click Connect.
PBC: Select this option to use PBC (Push Button) method to add a wireless
client. Click Connect.
Once you click Connect, you will have a 120 second time limit to apply the
settings to your wireless client(s) and successfully establish a connection.
40D-Link DIR-860L User Manual
Section 3 - Conguration
Check the box to enable the wireless function. If you do not want to use wireless,
uncheck the box to disable all the wireless functions.
Select the time frame that you would like your wireless network enabled. The schedule
may be set to "MXBZT. Any schedule you create will be available in the drop-down
menu. Click New Schedule to create a schedule.
Service Set Identier (SSID) is the name of your wireless network. Create a name for
your wireless network using up to 32 characters. The SSID is case-sensitive.
4FMFDUPOFPGUIFGPMMPXJOH
.JYFEBDOBOEB - Select if you are using both 802.11ac, 802.11
n, and 802.11a wireless clients.
.JYFEBDBOEOSelect if you are using both 802.11 ac and 802.11 n
wireless clients.
.JYFEOBOEB - Select if you are using both 802.11n and 802.11a
wireless clients.
BD0OMZ - Select only if all of your wireless clients are 802.11ac.
O0OMZ - Select only if all of your wireless clients are 802.11n.
The "VUP$IBOOFM4DBO setting can be selected to allow the DIR-860L to choose the channel with the least amount of interference.
Indicates the channel setting for the DIR-860L. By default the channel is set to 6. The Channel can be changed to t the channel setting for an existing wireless
network or to customize the wireless network. If you enable "VUP$IBOOFM4DBO, this option will be greyed out.
4FMFDUUIF$IBOOFM8JEUI
"VUP - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
.)[ - Select if you are not using any 802.11n wireless clients.
Select Invisible if you do not want the SSID of your wireless network to be broadcast by the DIR-860L. If Invisible is selected, the SSID of the DIR-860L will not
be seen by site survey utilities so your wireless clients will have to know the SSID of your DIR-860L in order to connect to it.
Refer to the appendix in the back of the manual for more information regarding wireless security.
Enable Wireless:
Schedule:
Wireless Network
Name:
802.11 Mode:
Enable Auto Channel
Scan:
Wireless Channel:
Manual Wireless Settings
Channel Width:
Visibility Status:
Wireless Security:
802.11ac draft (2.4GHz)
If you are unfamiliar with the types of wireless security, more information is located in the appendix at back of this manual.
41D-Link DIR-860L User Manual
Section 3 - Conguration
802.11ac draft (5GHz)
Check the box to enable the wireless function. If you do not want to use wireless,
uncheck the box to disable all the wireless functions.
Select the time frame that you would like your wireless network enabled. The schedule
may be set to "MXBZT. Any schedule you create will be available in the drop-down
menu. Click New Schedule to create a schedule.
Service Set Identier (SSID) is the name of your wireless network. Create a name for
your wireless network using up to 32 characters. The SSID is case-sensitive.
4FMFDUPOFPGUIFGPMMPXJOH
O0OMZ - Select only if all of your wireless clients are 802.11n.
BD0OMZ - Select if all of your wireless clients are 802.11ac.
.JYFEOBOEB - Select if you are using both 802.11n and 802.11a
wireless clients.
.JYFEBDBOEO - Select if you are using both 802.11ac and 802.11n
wireless clients.
.JYFEBDBOEB - Select if you are using both 802.11ac and 802.11a
wireless clients.
The "VUP$IBOOFM4DBO setting can be selected to allow the DIR-860L to choose the channel with the least amount of interference.
Indicates the channel setting for the DIR-860L. By default the channel is set to 6. The Channel can be changed to t the channel setting for an existing wireless
network or to customize the wireless network. If you enable "VUP$IBOOFM4DBO, this option will be greyed out.
4FMFDUUIF$IBOOFM8JEUI
"VUP - Select if you are using both 802.11ac, 802.11n and non-802.11n wireless devices.
"VUP - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
.)[ - Select if you are not using any 802.11n wireless clients.
Select Invisible if you do not want the SSID of your wireless network to be broadcast by the DIR-860L. If Invisible is selected, the SSID of the DIR-860L will not
be seen by site survey utilities so your wireless clients will have to know the SSID of your DIR-860L in order to connect to it.
Refer to the next page for more information regarding wireless security.
Enable Wireless:
Schedule:
Wireless Network
Name:
802.11 Mode:
Enable Auto Channel
Scan:
Wireless Channel:
Channel Width:
Visibility Status:
Wireless Security:
42D-Link DIR-860L User Manual
Section 3 - Conguration
This section will allow you to change the local network settings of the router and to congure the DHCP settings.
Network Settings
43D-Link DIR-860L User Manual
Section 3 - Conguration
This section will allow you to congure the router settings.
Router Settings
Enter the IP address of the router. The default IP address
is 192.168.0.1.
If you change the IP address, once you click Save Settings,
you will need to enter the new IP address in your browser
in order to log in to the conguration utility in the future.
Enter the Subnet Mask. The default subnet mask is
255.255.255.0.
Enter a name for the router.
Enter the Domain name (Optional).
Uncheck the box to transfer the DNS server information
from your ISP to your computers. If checked, your
computers will use the router for a DNS server.
Router IP Address:
Subnet Mask:
Device Name:
Local Domain:
Enable DNS Relay:
44D-Link DIR-860L User Manual
Section 3 - Conguration
DHCP Server Settings
DHCP stands for Dynamic Host Control Protocol. The DIR-860L has a built-in DHCP server. The DHCP Server will automatically assign an IP address
to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP
Address Automatically”. When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-860L. The
DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting
and ending address of the IP address pool.
Check this box to enable the DHCP server on your router. Uncheck to
disable this function.
Enter the starting and ending IP addresses for the DHCP server’s IP
assignment range.
Note: If you statically (manually) assign IP addresses to your computers or
devices, make sure the IP addresses are outside of this range or you may
have an IP conict.
The length of time for the IP address lease. Enter the lease time in
minutes.
Enable this feature to broadcast your network’s DHCP server to LAN/
WLAN clients.
NetBIOS allows LAN hosts to discover all other computers within the network, enable this feature to allow the DHCP Server to oer
NetBIOS conguration settings.
Enable this feature to allow WINS information to be learned from the WAN side, disable to allow manual conguration.
This feature allows the conguration of a NetBIOS ‘domain’ name under which network hosts operates. This setting has no eect
if the ‘Learn NetBIOS information from WAN’ is activated.
Select the dierent type of NetBIOS node; Broadcast only, Point-to-Point, Mixed-mode, and Hybrid.
Enter your WINS Server IP address(es).
Enable DHCP
Server:
DHCP IP Address
Range:
DHCP Lease Time:
Always
Broadcast:
NetBIOS
Announcement:
Learn NetBIOS
from WAN:
NetBIOS Scope:
NetBIOS Node:
WINS IP Address:
45D-Link DIR-860L User Manual
Section 3 - Conguration
DHCP Reservation
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP
address only to that computer or device.
Note: This IP address must be within the DHCP IP Address Range.
Check this box to enable the reservation.
Enter the computer name or select from the drop-down
menu and click <<.
Enter the IP address you want to assign to the computer
or device. This IP Address must be within the DHCP IP
Address Range.
Enter the MAC address of the computer or device.
If you want to assign an IP address to the computer you
are currently on, click this button to populate the elds.
Click Save to save your entry. You must click Save Settings
at the top to activate your reservations.
Displays any reservation entries. Displays the host name
(name of your computer or device), MAC Address, and IP
address.
Check to enable the reservation.
Click the edit icon to make changes to the reservation entry.
Click to remove the reservation from the list.
Enable:
Computer Name:
IP Address:
MAC Address:
Copy Your PC’s
MAC Address:
Save:
DHCP
Reservations List:
Enable:
Edit:
Delete:
DHCP Reservations List
46D-Link DIR-860L User Manual
Section 3 - Conguration
Storage
This page will allow you to set up access to les on an external USB hard drive1 or thumb drive that is plugged into the router. You can do this
through local network or from the Internet using either a web browser or an app on your smartphone or tablet. You can create users that can be
allowed access to these les through SharePort Mobile services accessible through a web UI or on mobile devices using the SharePort Mobile app
available for iOS and Android.
1 Supports capacities of up to 1TB for USB storage drives.
Check this box if you wish to be able to access SharePort through a
browser as well as the mobile app.
Enter the port you want to use when accessing SharePort using a web
browser.
Enter the port you want to use when accessing SharePort through a
secure connection using a web browser.
Check this box if you wish to be able to access SharePort through a web
browser over the Internet.
To give a new user access to your SharePort storage, enter a User Name
and Password here. You can Add new users or choose existing users
from the drop-down menu if you wish to Edit or Delete them.
Note: The Admin password is the same as the admin password for the
router. The Guest password is “guest” and cannot be changed.
This list displays all of the users with access to the SharePort Mobile
content, what they can access, and their Read/Write Permissions.
All devices you have set up for SharePort access will be listed here.
This area will display the HTTP and HTTPS links to connect to your SharePort drive through a web browser from a device on
your network.
Enable SharePort
Web Access
HTTP Access Port:
HTTPS Access Port:
Allow Remote
Access:
User Creation:
User List:
Number of Devices:
SharePort Web
Access Link:
47D-Link DIR-860L User Manual
Section 3 - Conguration
Media Server
This page will allow you to enable a DLNA Media Server. DLNA (Digital Living Network Alliance) is the standard for the interoperability of Network
Media Devices (NMDs). The user can enjoy multimedia applications (music, pictures and videos) on your network connected PC or media devices.
If you agree to share media with devices, any computer or device that connects to your network can play your shared music, pictures and videos.
Note: The shared media may not be secure. Allowing any devices to stream is recommended only on secure networks.
Check to enable DLNA Media Server functions.
Choose a name for your DLNA media server so that it can be
found.
Choose the location of the folder you wish to share or check the
box to use the root folder of the entire drive.
Check to enable iTunes Server functions.
Choose the location of the iTunes Library folder you wish to share
or check the box to use the root folder if it is located on the root
folder of the connected drive.
Use this setting to enable USB 3.0 fuctionality for the USB port
on the back of the router. USB 3.0 provides high-speed transfer
speeds with compatible devices. This setting is disabled by
default, which means that the USB port will operate at the USB
2.0 specication.
DLNA Server:
DLNA Server
Name:
Folder:
iTunes Server:
Folder:
USB 3.0
48D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6
On this page, you can congure the IPv6 Connection type. There are two ways to set up the IPv6 Internet connection. You can use the Web-based
IPv6 Internet Connection Setup Wizard, or you can manually congure the connection.
If you are a beginner who has not congured a router before, click on the IPv6 Internet
$POOFDUJPO4FUVQ8J[BSEbutton and the router will guide you through a few simple
steps to get your network up and running.
If you are an advanced user who has congured a router before, click on the Manual
IPv6 Internet Connection Setup button to input all the settings manually.
49D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6 Internet Connection Setup Wizard
On this page, the you can congure the IPv6 Connection type using the IPv6 Internet Connection Setup Wizard.
Click the *1W*OUFSOFU$POOFDUJPO4FUVQ8J[BSE button and the router will guide
you through a few simple steps to get your network up and running.
Click Next to continue to the next page. Click Cancel to discard the changes made
and return to the main page.
The router will attempt to detect whether it is possible to obtain the IPv6 Internet
connection type automatically. If this succeeds then you will be guided through the
input of the appropriate parameters for the connection type found.
50D-Link DIR-860L User Manual
Section 3 - Conguration
However, if the automatic detection fails, you will be prompt to either Try again or
to click on the Guide me through the IPv6 settings button to initiate the manual
continuation of the wizard.
There are several connection types to choose from. If you are unsure of your
connection method, please contact your IPv6 Internet Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client
software on your computers has been removed or disabled. The 3 options available
on this page are*1WPWFS111P&4UBUJD*1WBEESFTTBOE3PVUF, and Tunneling
Connection.
Choose the required IPv6 Internet Connection type and click on the Next button
to continue. Click on the Prev button to return to the previous page. Click on the
Cancel button to discard all the changes made and return to the main page.
Click on the Next button to continue. Click on the Prev button to return to the previous page.
Click on the Cancel button to discard all the changes made and return to the main page.
51D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6 over PPPoE
After selecting the IPv6 over PPPoE option, you will be able to congure the IPv6
Internet connection that requires a username and password to get online. Most
DSL modems use this type of connection.
5IFGPMMPXJOHQBSBNFUFSTXJMMCFBWBJMBCMFGPSDPOöHVSBUJPO
PPPoE Session: Select the PPPoE Session value used here. This
option will state that this connection shares its
information with the already congured IPv6
PPPoE connection, or the user can create a new
PPPoE connection here.
User Name: Enter the PPPoE username used here. If you do not
know your user name, please contact your ISP.
Password: Enter the PPPoE password used here. If you do not
know your password, please contact your ISP.
Verify Password: Re-enter the PPPoE password used here.
Service Name: Enter the service name for this connection here.
This option is optional.
52D-Link DIR-860L User Manual
Section 3 - Conguration
The Link-local address is used by nodes and routers when
communicating with neighboring nodes on the same link. This mode
enables IPv6-capable devices to communicate with each other on
the LAN side.
Enter the WAN IPv6 address for the router here.
Enter the WAN subnet prex length value used here.
Enter the WAN default gateway IPv6 address used here.
Enter the WAN primary DNS Server address used here.
Enter the WAN secondary DNS Server address used here.
These are the settings of the LAN (Local Area Network) IPv6 interface for the router. The router’s LAN IPv6 Address conguration is
based on the IPv6 Address and Subnet assigned by your ISP. (A subnet with prex /64 is supported in LAN.)
4UBUJD*1W"EESFTT$POOFDUJPO
This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your
IPv6 conguration settings. You must enter the IPv6 address, Subnet Prex Length, Default Gateway, Primary DNS Server, and Secondary DNS
Server. Your ISP provides you with all of this information.
Use Link-Local
Address:
IPv6 Address:
Subnet Prex
Length:
Default Gateway:
Primary DNS
Address:
Secondary DNS
Address:
LAN IPv6 Address:
53D-Link DIR-860L User Manual
Section 3 - Conguration
The IPv6 Internet Connection Setup Wizard is complete.
Click on the Connect button to continue. Click on the Prev button to return to
the previous page. Click on the Cancel button to discard all the changes made
and return to the main page.
Tunneling Connection (6rd)
After selecting the Tunneling Connection (6rd) option, you can congure the IPv6 6rd connection settings.
Enter the 6rd IPv6 address and prex value used here.
Enter the IPv4 address used here.
Enter the IPv4 mask length used here.
Displays the IPv6 assigned prex value here.
Enter the 6rd border relay IPv4 address used here.
Enter the primary DNS Server address used here.
6rd IPv6 Prex:
IPv4 Address:
Mask Length:
Assigned
IPv6 Prex:
6rd Border Relay
IPv4 Address:
IPv6 DNS Server:
54D-Link DIR-860L User Manual
Section 3 - Conguration
Manual IPv6 Local Connectivity Setup
You can set up a local-only IPv6 Internet connection as well. If you want to congure an IPv6 connection that will not connect to the Internet, click
on the Manual IPv6 Local Connectivity Settings button.
Enable ULA:
Use Default
ULA Prex:
ULA Prex:
Current IPv6
ULA Settings:
Click here to enable Unique Local IPv6 Unicast Addresses settings.
Checking this box will automatically congure
the ULA prex for the default setting.
If you wish to choose your own ULA prex, enter it here.
This section with display the current settings for your IPv6 ULA.
55D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6 Manual Setup
5IFSFBSFTFWFSBMDPOOFDUJPOUZQFTUPDIPPTFGSPN"VUP%FUFDUJPO4UBUJD*1W"VUPDPOöHVSBUJPO4-""$%)$1W111P&*1WJO*1W5VOOFM
6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled.
56D-Link DIR-860L User Manual
Section 3 - Conguration
Static IPv6
Select Static IPv6 from the drop-down menu.
Enter the address settings supplied by your Internet provider (ISP).
Enter a subnet prex length.
Enter the default gateway for your IPv6 connection.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the router’s LAN Link-Local Address.
Check to enable the Autoconguration feature.
Choose either Stateful DHCPv6, 4-""$3%/44 or 4-""$4UBUFMFTT%)$1W from the drop-down menu.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6
Connection Is:
Use Link-Local
Address:
Subnet Prex
Length:
IPv6 Default
Gateway:
Primary/
Secondary IPv6
DNS Servers:
LAN IPv6 Address:
LAN Link-Local
Address:
Enable Automatic
IPv6 Address
Assignment:
Autoconguration
Type:
Router
Advertisement
Lifetime:
57D-Link DIR-860L User Manual
Section 3 - Conguration
Auto Conguration
Select "VUP%FUFDUJPO from the drop-down menu.
Select either Obtain DNS server address automatically or Use the
GPMMPXJOH%/4"EESFTT.
Enter the primary and secondary DNS server addresses.
Check this box to enable DHCP-PD services.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Automatic IPv6 Address Assignment feature.
Check this box to automatically enable DHCP-PD services.
Select Stateful (DHCPv6), 4-""$3%/44 or 4-""$4UBUFMFTT
DHCPv6.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6
Connection Is:
IPv6 DNS Settings:
Primary/Secondary
DNS Address:
Enable DHCP-PD:
LAN IPv6 Address:
LAN Link-Local
Address:
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconguration
Type:
Router
Advertisement
Lifetime:
58D-Link DIR-860L User Manual
Section 3 - Conguration
PPPoE
Select PPPoE from the drop-down menu.
Enter the PPPoE account settings supplied by your Internet provider.
Select Static if your ISP assigned you an IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and retype the password in the next box.
Enter the ISP Service Name (optional).
Select either "MXBZTPO, On-Demand, or Manual.
Enter a maximum idle time during which the Internet connection is
maintained during inactivity.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is the default
MTU.
Select either Obtain DNS server address automatically or 6TFUIFGPMMPXJOH%/4"EESFTT.
Enter the primary and secondary DNS server addresses.
Check this box to enable DHCP prex delegation for each LAN on the network.
My IPv6
Connection Is:
PPPoE Session:
Address Mode:
IP Address:
Username:
Password:
Service Name:
Reconnection
mode:
Maximum Idle
Time:
MTU:
IPv6 DNS Settings:
Primary/Secondary
DNS Address:
59D-Link DIR-860L User Manual
Section 3 - Conguration
Enable DHCP-D:
LAN IPv6 Address:
LAN Link-Local
Address:
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconguration
Type:
IPv6 Address
Lifetime:
Enter the LAN (local) IPv6 address for the router.
Displays the router’s LAN Link-Local Address.
Check to enable the Automatic IPv6 Address Assignment feature.
Check this box to enable automatic conguration of the DHCP prex
delegation for each LAN on the network.
Select Stateful (DHCPv6), 4-""$3%/44 or 4-""$4UBUFMFTT%)$1W.
Enter the IPv6 Address Lifetime (in minutes).
60D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6 in IPv4 Tunneling
Select IPv6 in IPv4 Tunnel from the drop-down menu.
Enter the IPv4 remote address you will use.
Enter the IPv6 remote address you will use.
Enter the IPv4 local address you will use.
Enter the IPv6 local address you will use.
Select either Obtain DNS server address automatically or Use the
GPMMPXJOH%/4"EESFTT.
Enter the primary and secondary DNS server addresses.
Check this box to enable DHCP prex delegation for each LAN.
Enter the LAN (local) IPv6 address for the router.
Displays the router’s LAN Link-Local Address.
My IPv6
Connection Is:
Remote IPv4
Address:
Remote IPv6
Address:
Local IPv4 Address:
Local IPv6 Address:
IPv6 DNS Settings:
Primary/Secondary
DNS Address:
Enable DHCP-D:
LAN IPv6 Address:
LAN IPv6 Lin-Local
Address:
61D-Link DIR-860L User Manual
Section 3 - Conguration
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconguration
Type:
Router
Advertisement
Lifetime:
Check to enable the Automatic IPv6 Address Assignment feature.
Check this box to enable automatic conguration of the DHCP prex
delegation for each LAN on the network.
Select Stateful (DHCPv6), 4-""$ 3%/44 or 4-""$4UBUFMFTT
DHCPv6.
Enter the Router Advertisement Lifetime (in minutes).
62D-Link DIR-860L User Manual
Section 3 - Conguration
6to4
Select 6to4 from the drop-down menu.
Enter the IPv6 settings supplied by your ISP.
Enter the IPv6 relay supplied by your ISP.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
Check to enable the Automatic IPv6 Address Assignment feature.
Select Stateful (DHCPv6), 4-""$3%/44 or 4-""$4UBUFMFTT
DHCPv6.
Enter the IPv6 Address Lifetime (in minutes).
My IPv6
Connection Is:
6to4 Address:
6to4 Relay:
Primary/Secondary
DNS Address:
LAN IPv6 Address:
LAN Link-Local
Address:
Enable Automatic
IPv6 Address
Assignment:
Autoconguration
Type:
Router
Advertisement
Lifetime:
63D-Link DIR-860L User Manual
Section 3 - Conguration
6rd
Select 6rd from the drop-down menu.
Check this box if you want to minimize the number of routes to the
destination by using a hub and spoke method of networking.
Choose the 6rd DHCPv4 Option to automatically discover and populate
the data values, or Manual Conguration to enter the settings yourself.
Enter the 6rd IPv6 prex settings supplied by your ISP.
Your IPv4 address will appear here.
Enter the desired IPv4 mask length.
When an IPv6 prex is assigned, it will appear here.
Enter the 6rd Border Relay IPv4 address settings supplied by your ISP.
Enter the primary and secondary DNS server addresses.
Enter the LAN (local) IPv6 address for the router.
Displays the Router’s LAN Link-Local Address.
My IPv6
Connection Is:
Enable Hub and
Spoke Mode:
6rd Conguration:
6rd IPv6 Prex:
IPv4 Address:
Mask Length:
Assigned IPv6
Prex:
6rd Border Relay
IPv4 Address:
Primary/
Secondary DNS
Address:
LAN IPv6 Address:
LAN Link-Local
Address:
64D-Link DIR-860L User Manual
Section 3 - Conguration
Enable Automatic
IPv6 Address
Assignment:
Autoconguration
Type:
Router
Advertisement
Lifetime:
Check to enable the Automatic IPv6 Address Assignment feature.
Select Stateful (DHCPv6), 4-""$3%/44 or 4-""$ 4UBUFMFTT
DHCPv6.
Enter the IPv6 Address Lifetime (in minutes).
65D-Link DIR-860L User Manual
Section 3 - Conguration
Select Link-Local Only from the drop-down menu.
Displays the IPv6 address of the router.
My IPv6
Connection Is:
LAN IPv6 Address
Settings:
Link-Local Connectivity
66D-Link DIR-860L User Manual
Section 3 - Conguration
mydlink Settings
Displays whether your device is registered with a mydlink
account or not.
Displays the email address associated with your mydlink
account if you have an active account.
Click to go to the mydlink website to register your device or
edit your settings.
mydlink Service:
mydlink E-mail:
Register mydlink
Service:
Devices that are mydlink-enabled can be accessed and managed through the mydlink website and by using mydlink mobile apps for iOS and
Android. You cannot take advantage of these features without a mydlink account. If you have a mydlink account already, you can log in when you
rst set up the router, or by visiting this setup page.
67D-Link DIR-860L User Manual
Section 3 - Conguration
This page will allow you to open a single port. If you would like to open a range of ports, refer to the next page.
Enter a name for the rule or select an application from the
drop-down menu. Select an application and click << to
populate the elds.
Enter the IP address of the computer on your local network
that you want to allow the incoming service to. If your
computer is receiving an IP address automatically from the
router (DHCP), your computer will be listed in the “Computer
Name” drop-down menu.
Enter the port that you want to open next to Private Port
and Public Port. The private and public ports are usually the
same. The public port is seen from the Internet side, and
the private port is used by the application on the computer
within your local network.
Select TCP, UDP, or Both from the drop-down menu.
The schedule of time when the Virtual Server Rule will be
enabled. The schedule may be set to Always, which will allow
the particular service to always be enabled. You can create
your own times in the Tools > Schedules section.
Select "MMPX"MM (most common) or a created Inbound lter.
You may create your own inbound lters in the "EWBODFE
Inbound Filter page.
Name:
IP Address:
Private Port/
Public Port:
Protocol:
Schedule:
Inbound Filter:
Virtual Server
Advanced
68D-Link DIR-860L User Manual
Section 3 - Conguration
This page will allow you to open a single port or a range of ports.
Port Forwarding
Enter a name for the rule or select an application from the
drop-down menu. Select an application and click to populate
the elds.
Enter the IP address of the computer on your local network that
you want to allow the incoming service to. If your computer is
receiving an IP address automatically from the router (DHCP),
you computer will be listed in the “Computer Name” drop-
down menu. Select your computer and click <<.
Enter the TCP and/or UDP port or ports that you want to open.
You can enter a single port or a range of ports. Separate ports
XJUIBDPNNB&YBNQMF
The schedule of time when the Virtual Server Rule will be
enabled. The schedule may be set to "MXBZT, which will allow
the particular service to always be enabled. You can create your
own times in the Tools > Schedules section.
Select "MMPX"MM (most common) or a created Inbound lter.
You may create your own inbound lters in the "EWBODFE
Inbound Filter page.
Name:
IP Address:
TCP/UDP:
Schedule:
Inbound Filter:
69D-Link DIR-860L User Manual
Section 3 - Conguration
Enter a name for the rule. You may select a pre-dened
application from the drop-down menu and click.
This is the port used to trigger the application. It
can be either a single port or a range of ports.
Select the protocol of the trigger port (TCP, UDP, or Both).
This is the port number on the Internet side that
will be used to access the application. You may
dene a single port or a range of ports. You can use
a comma to add multiple ports or port ranges.
Select the protocol of the rewall port (TCP, UDP, or Both).
The schedule of time when the Application Rule will be
enabled. The schedule may be set to Always, which will
allow the particular service to always be enabled. You can
create your own times in the Tools > Schedules section.
Name:
Trigger:
Trac Type:
Firewall:
Trac Type:
Schedule:
Application Rules
Some applications, such as Internet gaming, video conferencing, Internet telephony and others, require multiple connections. These applications
have diculties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-860L.
If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port”
eld, select the protocol type as TCP or UDP, then enter the rewall (public) ports associated with the trigger port to open them for inbound trac.
70D-Link DIR-860L User Manual
Section 3 - Conguration
QoS Engine
This option is disabled by default. Enable this option for better
performance and experience with online games and other interactive
applications, such as VoIP.
This option is enabled by default when the QoS Engine option is
enabled. This option will allow your router to automatically determine
the uplink speed of your Internet connection.
This displays the detected uplink speed.
The speed at which data can be transferred from the router to your ISP.
This is determined by your ISP. ISPs state often speed as a download/
VQMPBEQBJSFH.CJUT,CJUT6TJOHUIJTFYBNQMFZPVXPVMEFOUFS
284. Alternatively you can test your uplink speed using an online speed
testing website or service.
A QoS Engine Rule identies a specic message ow and assigns a
priority to that ow. For most applications, automatic classication will
be adequate, and specic QoS Engine Rules will not be required.
The QoS Engine supports overlaps between rules, where more than
one rule can match for a specic message ow. If more than one rule is
found to match, the rule with the highest priority will be used.
Create a name for the rule that is meaningful to you.
The priority of the message ow is entered here -- 1 receives the highest
priority (most urgent) and 255 receives the lowest priority (least urgent).
The protocol used by the messages.
Enable QoS
Engine:
Automatic Uplink
Speed:
Measured Uplink
Speed:
Manual Uplink
Speed:
QoS Engine Rules:
Name:
Priority:
Protocol:
The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are
disabled and application priority is not classied automatically.
71D-Link DIR-860L User Manual
Section 3 - Conguration
The rule applies to a ow of messages whose LAN-side IP address falls within the range set here.
The rule applies to a ow of messages whose LAN-side port number is within the range set here.
The rule applies to a ow of messages whose WAN-side IP address falls within the range set here.
The rule applies to a ow of messages whose WAN-side port number is within the range set here.
Local IP Range:
Local Port Range:
Remote IP Range:
Remote Port
Range:
72D-Link DIR-860L User Manual
Section 3 - Conguration
Network Filters
Select5VSO."$'JMUFSJOH0ò, "MMPX."$BEESFTTFTMJTUFE
below, or %FOZ."$BEESFTTFTMJTUFECFMPX from the drop-
down menu.
Enter the MAC address you would like to lter.
To nd the MAC address on a computer, please refer to the
Networking Basics section in this manual.
Select a DHCP client from the drop-down menu and click << to
copy that MAC Address.
Click to remove the MAC address.
Congure MAC
Filtering:
MAC Address:
DHCP Client:
Clear:
Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers from accessing the network
according to their MAC addresses. You can either manually add a MAC address or select the MAC address from the list of clients
that are currently connected to the DIR-860L.
73D-Link DIR-860L User Manual
Section 3 - Conguration
Access Control
Click the "EE1PMJDZ button to start the Access Control Wizard. Add Policy:
The Access Control section allows you to control access in and out of your network. Use this feature as a parental control to
only grant access to approved sites, limit web access based on time or date, and/or block access from applications like P2P
utilities or games.
Click Next to continue with the wizard.
Access Control Wizard
74D-Link DIR-860L User Manual
Section 3 - Conguration
Enter a name for the policy and then click Next to continue.
4FMFDUBTDIFEVMFFH"MXBZTGSPNUIFESPQEPXONFOVBOE
then click Next to continue.
Enter the following information and then click Next to continue.
t "EESFTT5ZQF - Select IP address, MAC address, or Other
Machines.
t *1"EESFTT - Enter the IP address of the computer you want to
apply the rule to.
t .BDIJOF"EESFTT&OUFSUIF1$."$BEESFTTJF
Select the ltering method and then click Next to continue.
75D-Link DIR-860L User Manual
Section 3 - Conguration
&OUFSUIFSVMF
Enable - Check to enable the rule.
Name - Enter a name for your rule.
Dest IP Start - Enter the starting IP address.
Dest IP End - Enter the ending IP address.
Protocol - Select the protocol.
Dest Port Start - Enter the starting port number.
Dest Port End - Enter the ending port number.
To enable web logging, click Enable.
Click Save to save the access control rule.
Your newly created policy will now show up under Policy Table.
76D-Link DIR-860L User Manual
Section 3 - Conguration
Congure Website
Filter:
Website URL/
Domain:
Website Filters
Select either DENY computers access to ONLY these sites
or "--08DPNQVUFSTBDDFTTUP0/-:UIFTFTJUFT.
Enter the keywords or URLs that you want to allow or block.
Click Save Settings.
Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network.
To use this feature select to "MMPX or Deny, enter the domain or website and click Save Settings. You must also select "QQMZ
Web Filter under the Access Control section.
77D-Link DIR-860L User Manual
Section 3 - Conguration
Enter a name for the inbound lter rule.
Select "MMPX or Deny.
Check to enable rule.
Enter the starting IP address. Enter 0.0.0.0 if you do not want
to specify an IP range.
Enter the ending IP address. Enter 255.255.255.255 if you do
not want to specify and IP range.
Click the "EE button to apply your settings. You must click
Save Settings at the top to save the settings.
This section will list any rules that are created. You may click
the Edit icon to change the settings or enable/disable the rule,
or click the Delete icon to remove the rule.
Name:
Action:
Enable:
Remote IP Start:
Remote IP End:
Add:
Inbound Filter
Rules List:
The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can
congure inbound data ltering rules that control data based on an IP address range. Inbound Filters can be used with Virtual
Server, Port Forwarding, or Remote Administration features.
Inbound Filter
78D-Link DIR-860L User Manual
Section 3 - Conguration
SPI (Stateful Packet Inspection, also known as dynamic packet ltering)
helps to prevent cyber attacks by tracking the state of each session. It
validates that the trac passing through the session conforms to the
protocol.
Enable this feature to protect your network from certain kinds of
“spoong” attacks.
If an application has trouble working from behind the router, you can
expose one computer to the Internet and run the application on that
computer.
Note: Placing a computer in the DMZ may expose that computer to a variety
of security risks. Use of this option is only recommended as a last resort.
Specify the IP address of the computer on the LAN that you want to
have unrestricted Internet communication. If this computer obtains its IP
address automatically using DHCP, be sure to make a static reservation
on the Setup > Network Settings page so that the IP address of the
DMZ machine does not change.
Allows multiple machines on the LAN to connect to their corporate
network using PPTP protocol.
Allows multiple VPN clients to connect to their corporate network
using IPSec. Some VPN clients support traversal of IPSec through NAT.
This Application-level Gateway (ALG) may interfere with the operation
of such VPN clients. If you are having trouble connecting with your
corporate network, try turning this ALG o. Please check with the system
Enable SPI:
Anti-Spoof Check:
Enable DMZ:
DMZ IP Address:
PPTP:
IPSEC (VPN):
Firewall Settings
A rewall protects your network from the outside world. The DIR-860L oers a rewall type functionality. The SPI feature helps
prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications.
If you choose to expose a computer, you can enable Demilitarized Zone (DMZ). This option will expose the chosen computer
completely to the outside world.
79D-Link DIR-860L User Manual
Section 3 - Conguration
RTSP:
SIP:
administrator of your corporate network whether your VPN client supports NAT traversal.
Allows application that uses Real Time Streaming Protocol to receive streaming media from the Internet. QuickTime and Real Player
are some of the common applications using this protocol.
Allows devices and applications using VoIP (Voice over IP) to communicate across NAT. Some VoIP applications and devices have
the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are
having trouble making VoIP calls, try turning this ALG o.
80D-Link DIR-860L User Manual
Section 3 - Conguration
Enter a name for your route.
Enter the IP address of packets that will take this route.
Enter the netmask of the route, please note that the octets
must match your destination IP address.
Enter your next hop gateway to be taken if this route is used.
The route metric is a value from 1 to 16 that indicates the
cost of using this route. A value 1 is the lowest cost and 15
is the highest cost.
Select the interface that the IP packet must use to transit out
of the router when this route is used.
Name:
Destination IP:
Netmask:
Gateway:
Metric:
Interface:
Routing
The Routing option is an advanced method of customizing specic routes of data through your network.
81D-Link DIR-860L User Manual
Section 3 - Conguration
Advanced Wireless
This section will allow you to adjust the settings for the ()[CBOE
Set the transmission power of the antennas for the 2.4 GHz band.
This enables 802.11d operation. 802.11d is a wireless specication
developed to allow implementation of wireless networks in
countries that cannot use the 802.11 standard. This feature
should only be enabled if you are in a country that requires it.
WMM is QoS for your wireless network. This will improve the
quality of video and voice applications for your wireless clients.
Enable this option to reduce interference from other
wireless networks in your area. If the channel width
is operating at 40MHz and there is another wireless
network’s channel over-lapping and causing interference, the router will automatically change to 20MHz.
This section will allow you to adjust the settings for the ()[CBOE.
Set the transmission power of the antennas for the 5 GHz band.
This enables 802.11d operation. 802.11d is a wireless specication developed to allow implementation of wireless networks
in countries that cannot use the 802.11 standard. This feature should only be enabled if you are in a country that requires it.
WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.
Wireless Band
Transmit Power:
WLAN Partition:
WMM Enable:
HT20/40
Coexistence:
Wireless Band:
Transmit Power:
WLAN Partition:
WMM Enable:
This page allows you to change some of the advanced wireless settings of the DIR-860L. It is recommended that you only change these settings if
you are familiar with their functions and proper settings, or are instructed to do so.
82D-Link DIR-860L User Manual
Section 3 - Conguration
Wi-Fi Protected Setup
Enable the Wi-Fi Protected Setup feature.
Note: if this option is unchecked, the WPS button
on the side of the router will be disabled.
Check to disable the option of conguring the WPS PIN options.
A PIN is a unique number that can be used to add the router
to an existing network or to create a new network. Only the
Administrator (“admin” account) can change or reset the PIN.
Shows the current PIN.
Create a random number that is a valid PIN. This becomes the router’s
PIN. You can then use this pin to access your wireless network.
Restore the default PIN of the router.
Enable:
Lock WPS-PIN
Setup:
PIN Settings:
Current PIN:
Generate New
PIN:
Reset PIN to
Default:
Wi-Fi Protected Setup (WPS) is a simplied method for securing your wireless network during the “Initial setup” as well as the “Add New Device”
processes. The Wi-Fi Alliance (WFA) has certied WPS across many dierent products and manufacturers. The process as simple as pressing a
button for the Push-Button Method or correctly entering an 8-digit code for the PIN Code Method. The time reduction in setup and ease of use are
signicant, and the highest wireless security setting of WPA2 is automatically used.
83D-Link DIR-860L User Manual
Section 3 - Conguration
This Wizard helps you add wireless devices to the wireless network.
The wizard will either display the wireless network settings to guide you through manual conguration, prompt you to enter the
PIN for the device, or ask you to press the conguration button on the device. If the device supports Wi-Fi Protected Setup and
has a conguration button, you can add it to the network by pressing the conguration button on the device and then the on the
router within 120 seconds. The status LED on the router will ash three times if a device has been successfully added to the network.
There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A registrar
only allows devices onto the wireless network if you have entered the correct PIN, or pressed a special WPS button on the device.
The router acts as a registrar for the network, although other devices may act as a registrar as well.
Click to start the wizard, and refer to page 38 for further instructions.
Add Wireless
Station:
You can also simply press the WPS button on the side of the router, and then press the
WPS button on your wireless client within 120 seconds to automatically connect without
logging into the router.
Refer to page 106 for more information.
WPS Button
WPS Button
84D-Link DIR-860L User Manual
Section 3 - Conguration
To use the Universal Plug and Play (UPnP™) feature click
on Enabled. UPnP provides plug and play functionality
with compatible networking equipment, software and
peripherals.
Checking the box will allow the DIR-860L to respond
to pings. Unchecking the box may provide some extra
security from hackers.
Select from the drop-down menu if you would like to apply
the Inbound Filter to the WAN ping. Refer to the Inbound
Filters section for more information.
You may set the port speed of the Internet/WAN port to
10Mbps, 100Mbps, 1000Mbps, or Auto (recommended).
Check the box to allow multicast trac to pass through
the router from the Internet (IPv4).
Check the box to allow multicast trac to pass through
the router from the Internet (IPv6).
Enable UPnP:
WAN Ping:
WAN Ping Inbound
Filter:
WAN Port Speed:
Enable IPV4
Multicast Streams:
Enable IPV6
Multicast Streams:
Advanced Network
This page allows you to change some of the advanced network settings of the DIR-860L. It is recommended that you only change these settings if
you are familiar with their functions and proper settings, or are instructed to do so.
85D-Link DIR-860L User Manual
Section 3 - Conguration
Guest Zone
Check to allow network connectivity between the dierent zones
created.
Check to enable the Guest Zone feature for the 2.4 GHz band.
The timeframe when the Guest Zone will be active. The schedule may
be set to "MXBZT, which will allow the particular service to always be
enabled. You can create your own times in the Tools > Schedules
section or click "EE/FX.
Enter a wireless network name (SSID) that is dierent from that of your
main wireless network.
If you want to choose a security mode for the 2.4 GHz band, choose
from the drop-down menu.
Check to enable the Guest Zone feature for the 5 GHz band.
The timeframe when the Guest Zone will be active. The schedule may be set to "MXBZT, which will allow the particular service to
always be enabled. You can create your own times in the Tools > Schedules section or click "EE/FX.
Enter a wireless network name (SSID) that is dierent from that of your main wireless network and 2.4GHz band guest zone (if enabled).
If you want to choose a security mode for the 5 GHz band, choose from the drop-down menu.
Enable Routing
Between Zones:
Enable Guest Zone:
Schedule:
Wireless Network
Name:
Security Mode:
Enable Guest Zone:
Schedule:
Wireless Network
Name:
Security Mode:
The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate
from your main wireless network. You may congure dierent zones for the 2.4GHz and 5GHz wireless bands.
86D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6 Firewall
The DIR-860L’s IPv6 Firewall feature allows you to congure which kind of IPv6 trac is allowed to pass through the device. The DIR-860L’s IPv6
Firewall functions in a similar way to the IP Filters feature.
Check the box to enable the IPv6 rewall simple security.
Select an action from the drop-down menu.
Enter a name to identify the IPv6 rewall rule.
Use the drop-down menu to select the time schedule that the IPv6
Firewall Rule will be enabled on. The schedule may be set to "MXBZT,
which will allow the particular service to always be enabled. You can
create your own times in the Tools > Schedules section.
Use the Source drop-down menu to specify the interface that connects
to the source IPv6 addresses of the rewall rule.
Enter the source IPv6 address range in the adjacent IP Address Range
eld.
Use the Destination drop-down menu to specify the interface that
connects to the destination IP addresses of the rewall rule.
Select the protocol of the rewall port ("MM, TCP, UDP, or ICMP).
Enter the rst port of the range that will be used for the rewall rule
in the rst box and enter the last port in the eld in the second box.
Enable IPv6 Simple
Security:
Congure IPv6
Firewall:
Name:
Schedule:
Source:
IP Address Range:
Destination:
Protocol:
Port Range:
87D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6 Routing
Check the box next to the route you wish to enable.
Enter a specic name to identify this route.
This is the IP address of the router used to reach the specied
destination. You can also enter the IPv6 address prex length
of the packets that will take this route.
The route metric is a value from 1 to 16 that indicates the cost
of using this route. A value 1 is the lowest cost and 15 is the
highest cost.
Use the drop-down menu to specify if the IP packet must use
the WAN or LAN interface to transit out of the Router.
Enter the next hop that will be taken if this route is used.
Route List:
Name:
Destination IP/
Prex Length:
Metric:
Interface:
Gateway:
This page allows you to specify custom routes that determine how data is moved around your network.
88D-Link DIR-860L User Manual
Section 3 - Conguration
Admin
This page will allow you to change the Administrator password. You can also enable Remote Management. Admin has full read/write access to the
router’s settings.
Tools
Here you can enter a new password for the Administrator Login Name. The
administrator can make changes to the settings. Enter the new password
twice for verication.
Enter a name for your router.
Enables a CAPTCHA challenge-response test, which requires users to type
letters or numbers from a distorted image displayed on the screen This
prevents unauthorized users from using automated methods to gain
access your wireless network.
Check to enable HTTPS to connect to the router securely. This means
to connect to the router, you must enter IUUQTEMJOLSPVUFSMPDBM or
https://192.168.0.1 (for example) instead of IUUQEMJOLSPVUFSMPDBMor
http://192.168.0.1.
Remote management allows the DIR-860L to be congured from the
Internet by a web browser. A username/password is still required to access
the Web Management interface.
5IFQPSUOVNCFSVTFEUPBDDFTTUIF%*3-JTVTFEJOUIF63-&YBNQMFIUUQYYYY where x.x.x.x is the Internet IP address of
the DIR-860L and 8080 is the port used for the Web Management interface. If you have enabled )55144FSWFS you must enter IUUQT
as part of the URL to access the router remotely.
This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the
Delete icon to remove the rule. Details will display the current status of the rule.
Admin
Password:
Gateway Name:
Enable Graphical
Authentication:
Enable HTTPS
Server:
Enable Remote
Management:
Remote Admin
Port:
Remote Admin
Inbound Filter:
89D-Link DIR-860L User Manual
Section 3 - Conguration
Time
Displays the current date and time of the router.
Select your Time Zone from the drop-down menu.
To select Daylight Saving time manually, select enabled or
disabled, and enter a start date and an end date for daylight
saving time.
NTP is short for Network Time Protocol. An NTP server will
synchronize the time and date with your router. This will only
connect to a server on the Internet, not a local server. Check
the box to enable this feature.
Enter the IP address of an NTP server or select one from the
drop-down menu.
To manually input the time, enter the values in these elds
for the Year, Month, Day, Hour, Minute, and Second and then
click Set Time.
You can also click Sync Your Computer’s Time Settings to
sync the date and time with that of the computer you are
currently using.
Time:
Time Zone:
Enable Daylight
Saving:
Enable NTP Server:
NTP Server Used:
Manual:
The Time Conguration option allows you to congure, update, and maintain the correct time on the internal system clock.
From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be congured to
automatically adjust the time when needed.
90D-Link DIR-860L User Manual
Section 3 - Conguration
SysLog
The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a
SysLog server on your network.
Enable Logging to
SysLog Server: Check this box to send the router logs to a SysLog Server.
91D-Link DIR-860L User Manual
Section 3 - Conguration
Email Settings
The Email feature can be used to send the system log les, router alert messages, and rmware update notications to an
email address.
Enable Email
Notication:
From Email
Address:
To Email Address:
SMTP Server
Address:
SMTP Server Port:
Enable
Authentication:
Account Name:
Password:
On Log Full:
On Schedule:
Schedule:
Details:
When this option is enabled, router activity logs are emailed
to a designated email address.
This email address will appear as the sender when you receive
a log le or rmware upgrade notication via email.
Enter the email address where you want the email to be sent.
Enter the SMTP server address for sending email.
Enter the SMTP port used on the server.
Check this box if your SMTP server requires authentication.
Enter your account for sending email.
Enter the password associated with the account. Re-type the
password associated with the account.
When this option is selected, logs will be sent via email to your
account when the log is full.
Selecting this option will send the logs via email according to schedule.
This option is enabled when On Schedule is selected. You can select a schedule from the list of dened schedules.
To create a schedule, go to 5PPMT4DIFEVMFT.
Here you can choose from a drop down menu whether email details are kept in the log or not.
92D-Link DIR-860L User Manual
Section 3 - Conguration
Use this option to save the current router conguration settings
to a le on the hard disk of the computer you are using. First, click
the Save Conguration button. A le dialog will appear, allowing
you to select a location and le name for the settings.
Use this option to load previously saved router conguration
settings. First, use the Browse option to nd a previously saved le
of conguration settings. Then, click the Load button to transfer
those settings to the router.
This option will restore all conguration settings back to the
settings that were in eect at the time the router was shipped
from the factory. Any settings that have not been saved will be lost,
including any rules that you have created. If you want to save the
current router conguration settings, use the Save button above.
Click to reboot the router.
Save Settings to
Local Hard Drive:
Load Settings
from Local Hard
Drive:
Restore to
Factory Default
Settings:
Reboot Device:
System
This section allows you to manage the router’s conguration settings, reboot the router, and restore the router to the factory
default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
93D-Link DIR-860L User Manual
Section 3 - Conguration
Firmware
Choose File:
Upload:
After you have downloaded the new rmware, click
Choose File to locate the rmware update on your
hard drive.
Click Upload to complete the rmware upgrade.
You can upgrade router’s rmware using this feature. Make sure the rmware you want to use is on the local hard drive of the computer you are
using. Click on Choose File to locate the rmware le to be used for the update. Please check the D-Link support website for rmware updates at
IUUQTVQQPSUEMJOLDPN. You can download rmware upgrades to your hard drive from this site.
After you have downloaded the new language pack,
click Choose File to locate the language pack le on
your hard drive.
Click Upload to complete the language pack upgrade.
Language Pack
You can change the language of the web UI by uploading available
language packs.
Choose File:
Upload:
This section shows the details of the current rmware
version that is installed. Click on the check now
button to check online for new rmware versions.
Firmware
Information
Firmware Upgrade
You can change update the internal router software by uploading a
new rmware version.
94D-Link DIR-860L User Manual
Section 3 - Conguration
Dynamic Domain Name System is a method of keeping a domain name
linked to a changing IP Address. Check the box to enable DDNS.
Select your DDNS provider from the drop-down menu or enter the
DDNS server address.
Enter the Host Name that you registered with your DDNS service
provider.
Enter the Username or key for your DDNS account.
Enter the Password or key for your DDNS account.
Enter a timeout time (in hours).
Displays the current connection status.
Check the Enable box to enable DDNS for IPv6 Hosts.
Select your DDNS provider from the drop-down menu or enter the
DDNS server address.
Enter the Host Name that you registered with your DDNS service provider.
Displays the list of active IPv6 Dynamic DNS addresses.
Enable Dynamic
DNS:
Server Address:
Host Name:
Username or
Key:
Password or Key:
Timeout:
Status:
Enable DDNS for
IPv6 Hosts
IPv6 Address:
Host Name:
IPv6 DDNS List:
Dynamic DNS
The DDNS feature allows you to host a server (Web, FTP, Game Server, etc.) using a domain name that you have purchased with your dynamically
assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends
can enter your domain name to connect to your server no matter what your IP address is.
95D-Link DIR-860L User Manual
Section 3 - Conguration
The Ping Test is used to send Ping packets to test if a
computer is connected to the Internet. Enter the IP address
that you wish to Ping and click Ping.
Enter the IPv6 address that you wish to Ping and click Ping.
The results of your ping attempts will be displayed here.
System Check
Ping Test:
IPv6 Ping Test:
Ping Results:
96D-Link DIR-860L User Manual
Section 3 - Conguration
Enter a name for your new schedule.
Select a day, a range of days, or All Week to include every day.
Check "MM%BZIST to schedule the entire day.
Choose a 24 hour or 12 hour clock-style.
Enter a start time for your schedule.
Enter an end time for your schedule.
The list of schedules will be listed here. Click the Edit icon to
make changes or click the Delete icon to remove the schedule.
Name:
Days:
All Day - 24 Hrs:
Time Format:
Start Time:
End Time:
Schedule Rules
List:
Schedules
Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you can create
a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.
97D-Link DIR-860L User Manual
Section 3 - Conguration
This page displays the current information for the DIR-860L. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection
is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use
Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use
Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.
Displays the router’s time and rmware version.
Displays the MAC address and the public IP settings
Displays the MAC address and the private (local) IP settings for the router.
Displays the 2.4GHz wireless MAC address and your wireless settings such as
SSID and Channel.
Displays the 5GHz wireless MAC address and your wireless settings such as SSID
and Channel.
Displays computers and devices that are connected to the router via Ethernet
and that are receiving an IP address assigned by the router (DHCP).
Displays the group address of any IGMP multicasts.
General:
WAN:
LAN:
Wireless LAN1:
Wireless LAN2:
LAN Computers:
IGMP Multicast
Memberships:
Device Info
Status
98D-Link DIR-860L User Manual
Section 3 - Conguration
Logs
Log Options:
Refresh:
First Page:
Last Page:
Previous:
Next:
Clear:
Email Now:
Save Log:
You can select the types of messages that you want to display
from the log. System Activity, Debug Information, Attacks,
Dropped Packets, and Notice messages can be selected. Click
"QQMZ-PH4FUUJOHT/PX to activate your settings.
Updates the log details on the screen so it displays any recent
activity.
Click to go to the rst page.
Click to go to the last page.
Click to go back one page.
Click to go to the next page.
Clears all of the log contents.
This option will send a copy of the router log to the email
address congured in the Tools > Email Settings screen.
This option will save the router log to a le on your computer.
The router automatically logs (records) events of possible interest in its internal memory. If there isn’t enough internal memory for all events, logs
of the oldest events are deleted rstand replaced with logs of the most recent events. The Logs option allows you to view the router logs. You can
dene what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can
send the log les to a computer on your network that is running a Syslog utility.
99D-Link DIR-860L User Manual
Section 3 - Conguration
Statistics
The screen below displays the Trac Statistics. Here you can view the amount of packets that pass through the DIR-860L on both the WAN, LAN ports
and the wireless segments. The trac counter will reset if the device is rebooted.
100D-Link DIR-860L User Manual
Section 3 - Conguration
Internet Sessions
The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a
program or application on a LAN-side computer and a program or application on a WAN-side computer.
101D-Link DIR-860L User Manual
Section 3 - Conguration
The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the
connected wireless clients.
Wireless
102D-Link DIR-860L User Manual
Section 3 - Conguration
Routing
This page will display your current routing table.
103D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6
The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
104D-Link DIR-860L User Manual
Section 3 - Conguration
IPv6 Routing
This page displays the IPV6 routing details congured for your router.
105D-Link DIR-860L User Manual
Section 3 - Conguration
Support
The Support pages let you jump to descriptions of the settings and their functions.
106D-Link DIR-860L User Manual
Section 4 - Security
Connect a Wireless Client to your Router
WPS Button
Step 2 - Within 120 seconds, press the WPS button on your wireless client (or launch the software utility and start the WPS
process).
The easiest way to securely connect your wireless devices to the router is using WPS (Wi-Fi Protected Setup). Most wireless
devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button
(or a software utility with WPS) that you can press to connect to the DIR-860L router. Please refer to the user manual for the
XJSFMFTTEFWJDFZPVXBOUUPDPOOFDUUPNBLFTVSFZPVVOEFSTUBOEIPXUPFOBCMF8140ODFSFBEZGPMMPXUIFTUFQTCFMPX
Step 1 - Press the WPS button on the DIR-860L for about 1 second. The Internet LED on the front will start to blink.
Step 3 - Allow up to 1 minute while your connection is congured. Once the Internet light stops blinking, you will be connected
and your wireless connection will be secure with WPA2.
WPS Button
107D-Link DIR-860L User Manual
Section 4 - Security
Windows® 7
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your
wireless adapter. If you are joining an existing network, you will need to know the security key or password being used.
1. Click on the wireless icon in your system tray (lower-right corner).
2. The utility will display any available wireless networks in your area.
Wireless Icon
WPA/WPA2
108D-Link DIR-860L User Manual
Section 4 - Security
3. Highlight the wireless connection with Wi-Fi name (SSID) you would
like to connect to and click the Connect button.
If you get a good signal but cannot access the Internet, check your
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
4. The following window appears while your computer tries to
connect to the router.
109D-Link DIR-860L User Manual
Section 4 - Security
5. Enter the same security key or passphrase (Wi-Fi password) was set
for your router and click Connect. You can also connect by pushing
the WPS button on the router.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.
110D-Link DIR-860L User Manual
Section 4 - Security
WPS
The WPS feature of the DIR-860L can be congured using Windows® 7. Carry out the following steps to use Windows® 7 to
DPOöHVSFUIF814GFBUVSF
1. Click the Start button and select Computer from the Start menu.
2. Click Network on the left side.
111D-Link DIR-860L User Manual
Section 4 - Security
3. Double-click the DIR-860L.
4. Input the WPS PIN number (displayed in the WPS window on the
Setup > Wireless Setup menu in the Router’s Web UI) and click
Next.
112D-Link DIR-860L User Manual
Section 4 - Security
5. Type a name to identify the network.
6. To congure advanced settings, click the icon.
Click Next to continue.
113D-Link DIR-860L User Manual
Section 4 - Security
7. The following window appears while the Router is being
congured.
Wait for the conguration to complete.
8. The following window informs you that WPS on the router has
been setup successfully.
Make a note of the security key as you may need to provide this
security key if adding an older wireless device to the network in
the future.
9. Click Close to complete WPS setup.
114D-Link DIR-860L User Manual
Section 5 - Connecting to a Wireless Network
Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another utility, please refer to the user manual of
your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to
the Windows Vista® utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select Connect to a network.
If you receive the Wireless Networks Detected bubble, click on the
center of the bubble to access the utility.
or
The utility will display any available wireless networks in your area. Click
on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
115D-Link DIR-860L User Manual
Section 5 - Connecting to a Wireless Network
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
2. Highlight the Wi-Fi name (SSID) you would like to connect to and
click Connect.
1. Open the Windows Vista® Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower right corner of
screen). Select Connect to a network.
116D-Link DIR-860L User Manual
Section 5 - Connecting to a Wireless Network
3. Enter the same security key or passphrase (Wi-Fi password) was set for
your router and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.
117D-Link DIR-860L User Manual
Section 5 - Connecting to a Wireless Network
WPS/WCN 2.0
The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up
depends on whether you are using Windows Vista® to congure the router or third party software.
When you rst set up the router, Wi-Fi protection is disabled and uncongured. To enjoy the benets of Wi-Fi protection, the
SPVUFSNVTUCFCPUIFOBCMFEBOEDPOöHVSFE5IFSFBSFUISFFCBTJDNFUIPETUPBDDPNQMJTIUIJTVTF8JOEPXT7JTUBTCVJMUJO
support for WCN 2.0, use software provided by a third party, or manually congure.
If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the
Current PIN that is displayed on the "EWBODFE > Wi-Fi Protected Setup section or choose to click the Generate New PIN
button or Reset PIN to Default button.
If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are nished, proceed
to the next section to set up the newly-congured router.
118D-Link DIR-860L User Manual
Section 5 - Connecting to a Wireless Network
Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Conguration Utility). The following instructions are for Service
Pack 2 users. If you are using another utility, please refer to the user manual of your wireless adapter for help with connecting
to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select 7JFX"WBJMBCMF8JSFMFTT/FUXPSLT.
If you receive the Wireless Networks Detected bubble, click on the
center of the bubble to access the utility.
or
The utility will display any available wireless networks in your area. Click
on a Wi-Fi network (displayed using the SSID) and click the Connect
button.
If you get a good signal but cannot access the Internet, check you
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
119D-Link DIR-860L User Manual
Section 5 - Connecting to a Wireless Network
It is recommended to enable WPA on your wireless router or access point before conguring your wireless adapter. If you are
joining an existing network, you will need to know the WPA key being used.
2. Highlight the Wi-Fi network (SSID) you would like to connect
to and click Connect.
1. Open the Windows® XP Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower-right corner
of screen). Select 7JFX"WBJMBCMF8JSFMFTT/FUXPSLT.
WPA/WPA2
120D-Link DIR-860L User Manual
Section 5 - Connecting to a Wireless Network
3. The Wireless Network Connection box will appear. Enter the WPA-PSK
Wi-Fi password and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WPA-PSK settings are correct. The
Wi-Fi password must be exactly the same as on the wireless router.
121D-Link DIR-860L User Manual
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DIR-860L. Read the
following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a dierent
operating system, the screenshots on your computer will look similar to the following examples.
1. Why can’t I access the web-based conguration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you
have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must
be on the same IP subnet to connect to the web-based utility.
t .BLFTVSFZPVIBWFBOVQEBUFE+BWBFOBCMFEXFCCSPXTFS8FSFDPNNFOEUIFGPMMPXJOH
- Microsoft Internet Explorer® 7 and higher
- Mozilla Firefox 3.5 and higher
- Google™ Chrome 8 and higher
- Apple Safari 4 and higher
t 7FSJGZQIZTJDBMDPOOFDUJWJUZCZDIFDLJOHGPSTPMJEMJOLMJHIUTPOUIFEFWJDF*GZPVEPOPUHFUBTPMJEMJOLMJHIUUSZVTJOHB
dierent cable or connect to a dierent port on the device if possible. If the computer is turned o, the link light may not be
on.
t %JTBCMFBOZ*OUFSOFUTFDVSJUZTPGUXBSFSVOOJOHPOUIFDPNQVUFS4PGUXBSFöSFXBMMTTVDIBT;POF"MBSN#MBDL*DF4ZHBUF
Norton Personal Firewall, and Windows® XP rewall may block access to the conguration pages. Check the help les included
with your rewall software for more information on disabling or conguring it.
122D-Link DIR-860L User Manual
Section 6 - Troubleshooting
t $POöHVSFZPVS*OUFSOFUTFUUJOHT
t (PUPStart > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click
the button to restore the settings to their defaults.
t $MJDLUIFConnection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
t (PUPUIF"EWBODFE tab and click the button to restore these settings to their defaults. Click OK three times.
t $MPTFZPVSXFCCSPXTFSJGPQFOBOEPQFOJU
t "DDFTTUIFXFCNBOBHFNFOU0QFOZPVSXFCCSPXTFSBOEFOUFSUIF*1BEESFTTPGZPVS%-JOLSPVUFSJOUIFBEESFTTCBS5IJT
should open the login page for your web management.
t *GZPVTUJMMDBOOPUBDDFTTUIFDPOöHVSBUJPOVOQMVHUIFQPXFSUPUIFSPVUFSGPSTFDPOETBOEQMVHCBDLJO8BJUTFDPOET
and try accessing the conguration. If you have multiple computers, try connecting using a dierent computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the
factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip
to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30
seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the
password box empty.
123D-Link DIR-860L User Manual
Section 6 - Troubleshooting
3. Why can’t I connect to certain sites or send and receive emails when connecting through my router?
If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail,
we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
To nd the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be
another computer, or a URL.
t$MJDLPOStart and then click Run.
t8JOEPXT¥BOE.FVTFSTUZQFJOcommand (Windows® NT, 2000, XP, Vista®, and 7 users type in cmd) and
press Enter (or click OK).
t0ODFUIFXJOEPXPQFOTZPVMMOFFEUPEPBTQFDJBMQJOH6TFUIFGPMMPXJOHTZOUBY
ping [url] [-f] [-l] [MTU value]
&YBNQMFping yahoo.com -f -l 1472
124D-Link DIR-860L User Manual
Section 6 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented
packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, if 1452 was the proper
value, the actual MTU size would be 1480, which is the optimum for the network you’re working with (1452+28=1480).
Once you nd your MTU, you can now congure your router with the proper MTU size.
5PDIBOHFUIF.56SBUFPOZPVSSPVUFSGPMMPXUIFTUFQTCFMPX
t0QFOZPVSCSPXTFSFOUFSUIF*1BEESFTTPGZPVSSPVUFSBOEDMJDLOK.
t&OUFSZPVSVTFSOBNFBENJOBOEQBTTXPSECMBOLCZEFGBVMU$MJDLOK to enter the web conguration page
for the device.
t$MJDLPOSetup and then click Manual Congure.
t5PDIBOHFUIF.56FOUFSUIFOVNCFSJOUIF.56öFMEBOEDMJDLSave Settings to save your settings.
t5FTUZPVSFNBJM*GDIBOHJOHUIF.56EPFTOPUSFTPMWFUIFQSPCMFNDPOUJOVFDIBOHJOHUIF.56JOJODSFNFOUT
of ten.
125D-Link DIR-860L User Manual
Appendix A - Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless
connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link
wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able
to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of
wires. Wireless LANs are used increasingly in both home and oce environments, and public areas such as airports, coee shops
and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more eciently.
Increased mobility and the absence of cabling and other xed infrastructure have proven to be benecial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop
systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to
use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide
this link.
Wireless Basics
126D-Link DIR-860L User Manual
Appendix A - Wireless Basics
What is Wireless?
Wireless, or Wi-Fi technology is a way of connecting your computer to the network without using wires. Wi-Fi uses radio
frequencies to connect wirelessly, so you have the freedom to connect computers anywhere in your home or oce to your
network.
Why D-Link Wireless?
D-Link is the worldwide leader and an award winning designer, developer, and manufacturer of networking products. D-Link
delivers the performance you need at a price you can aord. D-Link oers all the products you need to build your network.
How does wireless work?
Wireless works similarly to how cordless phones work, using radio signals to transmit data from one point to another. In order
to access a network wirelessl you must be within the wireless network range area. There are two dierent types of wireless
OFUXPSLT8JSFMFTT-PDBM"SFB/FUXPSL8-"/BOE8JSFMFTT1FSTPOBM"SFB/FUXPSL81"/
8JSFMFTT-PDBM"SFB/FUXPSL8-"/
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has
a small antenna attached to it, which allows it to transmit data back and forth using radio signals. With an indoor access point
such as the DIR-860L, the signal can travel up to 300 feet. With an outdoor access point the signal can reach up to 30 miles to
serve places like manufacturing plants, industrial locations, school campuses, airports, golf courses, and many other outdoor
venues.
127D-Link DIR-860L User Manual
Appendix A - Wireless Basics
8JSFMFTT1FSTPOBM"SFB/FUXPSL81"/
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate within a range of
up to 30 feet.
Compared to WLAN, the speed and wireless operation range are both reduced when using WPAN, however WPAN doesn’t uses
less power, which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other
devices that operate on batteries.
Who uses wireless?
Wireless technology has become increasingly popular in recent years, whether it’s for home, oce, or business, D-Link has a
wireless solution.
Home
 t(JWFTFWFSZPOFBUIPNFCSPBECBOEBDDFTT
 t4VSGUIFXFCDIFDLFNBJMJOTUBOUNFTTBHFFUDGSPNBOZXIFSFJOZPVSIPNF
 t(FUTSJEPGUIFDBCMFTBSPVOEUIFIPVTF
 t4JNQMFBOEFBTZUPVTF
Small Oce and Home Oce
 t3FEVDFEDPTUPGTFUUJOHVQBOFUXPSL
 t3FNPUFMZBDDFTTZPVSPóDFOFUXPSLGSPNIPNF
 t4IBSF*OUFSOFUDPOOFDUJPOTBOEQSJOUFSTXJUINVMUJQMFDPNQVUFST
 t/POFFEUPEFEJDBUFPóDFTQBDF
128D-Link DIR-860L User Manual
Appendix A - Wireless Basics
Where is wireless used?
Wireless technology is expanding everywhere, not just at home or in the oce. People like the freedom of mobility and it’s
becoming so popular that more and more public facilities now provide wireless access. A wireless connection in public places
is usually called a “hotspot”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations
such as Airports, Hotels, Coee Shops, Libraries, Restaurants, and Convention Centers.
A wireless network is simple to setup, but if you’re installing one for the rst time it could be quite a task if you do not know
where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless
network.
Tips
Here are a few things to keep in mind when you install a wireless network.
$FOUSBMJ[FZPVSSPVUFSPS"DDFTT1PJOU
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to
place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have
a two-story home, you may need a repeater to boost the signal in order to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access
point. This can signicantly reduce any interference that these appliances might cause since they operate on same frequency.
129D-Link DIR-860L User Manual
Appendix A - Wireless Basics
Security
Don’t let neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the router’s
WPA or WEP security feature. Refer to product manual for detailed information on how to set up this feature.
5IFSFBSFUXPCBTJDNPEFTGPSXJSFMFTTOFUXPSLJOH
t Infrastructure – All wireless clients will connect to an access point or wireless router.
t "E)PD – Devices connect directly to one another, for peer-to-peer communication, using wireless network
adapters on each computer, such as two computers with wireless adaptors.
An Infrastructure network contains an Access Point or wireless router. All wireless devices, or clients, will connect to the wireless
router or access point in order to access the internet or other network resources.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All adapters must be in Ad-Hoc mode
to communicate.
Wireless Modes
130D-Link DIR-860L User Manual
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP
server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.)
At the prompt, type ipcong and press Enter.
This will display the IP address, subnet mask, and the
default gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation,
security settings, and the settings on your router.
Some rewall software programs may block a DHCP
request on newly installed adapters.
131D-Link DIR-860L User Manual
Appendix B - Networking Basics
Statically Assign an IP address
*GZPVBSFOPUVTJOHB%)$1DBQBCMFHBUFXBZSPVUFSPSZPVOFFEUPBTTJHOBTUBUJD*1BEESFTTQMFBTFGPMMPXUIFTUFQTCFMPX
Step 1
Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center.
Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network
Connections.
Windows® XP - Click on Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the -PDBM"SFB$POOFDUJPO which represents your network adapter and select Properties.
Step 3
Highlight *OUFSOFU1SPUPDPM5$1*1 and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet
as your network or the LAN IP address on your router.
&YBNQMF*GUIFSPVUFS}T-"/*1BEESFTTJTNBLFZPVS*1BEESFTT9
where X is a number between 2 and 99. Make sure that the number you choose is not
in use on the network. Set the Default Gateway the same as the LAN IP address of your
router (I.E. 192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
132D-Link DIR-860L User Manual
Appendix B - Networking Basics
Wireless Security
This section will show you the dierent levels of security you can use to protect your data from intruders. The DIR-860L oers the
GPMMPXJOHUZQFTPGTFDVSJUZ
t81"8J'J1SPUFDUFE"DDFTT   t81"14,1SF4IBSFE,FZ
 t81"8J'J1SPUFDUFE"DDFTT t81"14,1SF4IBSFE,FZ
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
5IFNBKPSJNQSPWFNFOUTPWFS8&1
t *NQSPWFEEBUBFODSZQUJPOUISPVHIUIF5FNQPSBM,FZ*OUFHSJUZ1SPUPDPM5,*15,*1TDSBNCMFTUIFLFZTVTJOHBIBTIJOH
algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is
based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
t 6TFSBVUIFOUJDBUJPOXIJDIXBTHFOFSBMMZNJTTJOHJO8&1UISPVHIUIFFYUFOTJCMFBVUIFOUJDBUJPOQSPUPDPM&"18&1
regulates access to a wireless network based on a computer’s hardware-specic MAC address, which is relatively simple
to be snied out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized
network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between
8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your
wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public
key encryption system to ensure that only authorized network users can access the network.
133D-Link DIR-860L User Manual
Appendix C - Technical Specications
Technical Specications
Device Interfaces
 tBCHOESBGUBDXJSFMFTT-"/
 t'PVS(JHBCJU-"/QPSUT
t10/100/1000 Gigabit WAN port
tUSB 3.0 port
"OUFOOB5ZQFT
 t*OUFSOBMBOUFOOBT
Standards
 t*&&&BDESBGU
 t*&&&O
 t*&&&H
 t*&&&C
 t*&&&B
 t*&&&
 t*&&&V
Security
t81"
- Personal/Enterprise
t81"
- Personal/Enterprise
 t8J'J1SPUFDUFE4FUVQ8141*/1#$
Power
 t*OQVUUP7"$)[
 t0VUQVU7%$"
USB Port Power
 t7"
Operating Temperature
 t¡$UP¡$¡'UP¡'
Humidity
 tNBYJNVNOPODPOEFOTJOH
Safety & Emissions
 t'$$$MBTT#
 t$&$MBTT#
 t$5JDL
 t%-/"
 t*1W3FBEZ
 t8J'J1SPUFDUFE4FUVQ814
 t8J'J.VMUJNFEJB8..
 t$PNQBUJCMFXJUI8JOEPXT
Dimensions
 t-DNJODIFT
 t8DNJODIFT
 t)DNJODIFT
1 Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including
volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely aect wireless signal range.
2 Frequency Range varies depending on country’s regulation.
3 The DIR-860L does not include 5.25-5.35GHz & 5.47-5.725GHz in some regions.
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
˗Reorient or relocate the receiving antenna.
˗Increase the separation between the equipment and receiver.
˗Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
˗Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Chain Brand Model Name
A
ntenna
Type Connector Gain
(dBi)
Loss of
External
Cable
(dB)
True Gain
(dBi) Remark
1WHA
YU SSR-30247 PCB
Antenna I-PEX 4 0.18 3.82
TX / RX
2WHA
YU SSR-30247 PCB
Antenna I-PEX 4 0.18 3.82 TX / RX
Note: The EUT has two Chains.ġ
5G Module FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
˗Reorient or relocate the receiving antenna.
˗Increase the separation between the equipment and receiver.
˗Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
˗Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor
environment only.
Devices will not permit operations on channels 120-132 for 11a and 11n/a which overlap the 5600 -
5650 MHz band.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
ġ
In the users manual of the end product, the end user has to be informed to keep at least 20cm
separation with the antenna while this end product is installed and operated. The end user has to be
informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end user has to also be informed that any changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate this equipment.ġIf the size of
the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be
available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Chain Brand Model Name
A
ntenna
Type Connector Gain
(dBi)
Loss of
External
Cable
(dB)
True Gain
(dBi) Remark
1WHA
YU SSR-30247 PCB
Antenna I-PEX 4 0.18 3.82
TX / RX
2WHA
YU SSR-30247 PCB
Antenna I-PEX 4 0.18 3.82 TX / RX
Note: The EUT has two Chains.
ġ
5G Module IC Statement
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou
transmetteur.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
ŅŦŤŭŢųŢŤŪǴůġťŦġŦŹűŰŴŪŤŪǴůġŢġŭŢġųŢťŪŢŤŪǴůġťŦġńŢůŢťŢĻ
ņŴŵŦġŦŲŶŪűŰġŤŶŮűŭŦġŤŰůġŭŰŴġŭǮŮŪŵŦŴġťŦġŦŹűŰŴŪŤŪǴůġŢġŭŢġųŢťŪŢŤŪǴůġťŦġŭŢġŊńġŦŴŵŢţŭŦŤŪťŰŴġűŢųŢġŶůġŢŮţŪŦůŵŦġůŰġŤŰůŵųŰŭŢťŰįġ
ņŴŵŦġŦŲŶŪűŰġŴŦġťŦţŦġŪůŴŵŢŭŢųġźġŰűŦųŢųġŤŰůġŶůŢġťŪŴŵŢůŤŪŢġŮǮůŪŮŢġťŦġijıġŤŮġŦůŵųŦġŦŭġųŢťŪŢťŰųġźġŴŶġŤŶŦųűŰįġ
The device could automatically discontinue transmission in case of absence of information to transmit,
or operational failure. Note that this is not intended to prohibit transmission of control or signaling
information or the use of repetitive codes where required by the technology.
Le dispositif pourrait automatiquement cesser d'émettre en cas d'absence d'informations à transmettre, ou une défaillance
opérationnelle. Notez que ce n'est pas l'intention d'interdire la transmission des informations de contrôle ou de
signalisation ou l'utilisation de codes répétitifs lorsque requis par la technologie.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful
interference to co-channel mobile satellite systems.
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz,
5470-5600 MHz and 5650-5725 MHz
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600
MHz et 5650-5725 MHz
The maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz)
to comply with the e.i.r.p. limit.
le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et
5470-5725 MHz doit se conformer à la limite de p.i.r.e.;
Users should also be advised that high-power radars are allocated as primary users (i.e. priority
users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés
utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces
radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the
e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz)
doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.
In the users manual of the end product, the end user has to be informed to keep at least 20cm
separation with the antenna while this end product is installed and operated. The end user has to be
informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end user has to also be informed that any changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate this equipment.ġIC statement
is required to be available in the users manual: This Class B digital apparatus complies with Canadian
ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un
type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de
sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.

This radio transmitter (identify the device by certification number, or model number if Category II) has
been approved by Industry Canada to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie
du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés
ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Chain Brand Model Name
A
ntenna
Type Connector Gain
(dBi)
Loss of
External
Cable
(dB)
True Gain
(dBi) Remark
1WHA
YU SSR-30247 PCB
Antenna I-PEX 4 0.18 3.82
TX / RX
2WHA
YU SSR-30247 PCB
Antenna I-PEX 4 0.18 3.82 TX / RX
Note: The EUT has two Chains.

Navigation menu