D Link SR500NA1 SMB Wireless N Gigabit VPN Router User Manual DLink DSR User Manual

D Link Corporation SMB Wireless N Gigabit VPN Router DLink DSR User Manual

User Manual

Unified Services RouterUser ManualDSR-500N/1000NRelease 1.01http://www.dlink.comBuilding Networks for People
User Manual Unified Services Router D-Link Corporation Copyright © 2010. http://www.dlink.com
Unified Services Router User Manual 1 User Manual DSR-500N/1000N Unified Services Router Version 1.0 Copyright © 2010 Copyright Notice This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Limitations of Liability UNDER NO CIRCUMSTANCES SHALL D-LINK OR ITS SUPPLIERS BE LIABLE FOR DAMAGES OF ANY CHARACTER (E.G. DAMAGES FOR LOSS OF PROFIT, SOFTWARE RESTORATION, WORK STOPPAGE, LOSS OF SAVED DATA OR ANY OTHER COMMERCIAL DAMAGES OR LOSSES) RESULTING FROM THE APPLICATION OR IMPROPER USE OF THE D-LINK PRODUCT OR FAILURE OF THE PRODUCT, EVEN IF D-LINK IS INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. FURTHERMORE, D-LINK WILL NOT BE LIABLE FOR THIRD-PARTY CLAIMS AGAINST CUSTOMER FOR LOSSES OR DAMAGES. D-LINK WILL IN NO EVENT BE LIABLE FOR ANY DAMAGES IN EXCESS OF THE AMOUNT D-LINK RECEIVED FROM THE END-USER FOR THE PRODUCT.
Unified Services Router User Manual 2 Table of Contents Chapter 1. Introduction ............................................................................................................................. 8 1.1 About this User Manual ............................................................................................ 8 1.2 Typographical Conventions ..................................................................................... 8 Chapter 2. Configuring Your Network: LAN Setup ............................................................................... 9 2.1 LAN Configuration ..................................................................................................... 9 2.1.1 LAN Configuration in an IPv6 Network ................................................................ 11 2.1.2 Configuring IPv6 Router Advertisements ............................................................ 14 2.2 VLAN Configuration ................................................................................................ 17 2.2.1 Associating VLANs to ports ................................................................................... 18 2.3 Configurable Port: DMZ Setup .............................................................................. 20 2.4 Universal Plug and Play (UPnP) ........................................................................... 21 Chapter 3. Connecting to the Internet: WAN Setup ........................................................................... 23 3.1 Internet Setup Wizard ............................................................................................. 23 3.2 WAN Configuration ................................................................................................. 24 3.2.1 WAN Port IP address ............................................................................................. 25 3.2.2 WAN DNS Servers ................................................................................................. 25 3.2.3 DHCP WAN ............................................................................................................. 25 3.2.4 PPPoE Profiles ........................................................................................................ 27 3.2.5 WAN Configuration in an IPv6 Network ............................................................... 28 3.2.6 Checking WAN Status ............................................................................................ 29 3.3 Bandwidth Controls ................................................................................................. 32 3.4 Features with Multiple WAN Links ........................................................................ 34 3.4.1 Auto Failover ............................................................................................................ 34 3.4.2 Load Balancing ........................................................................................................ 35 3.4.3 Protocol Bindings .................................................................................................... 36 3.5 Routing Configuration ............................................................................................. 37 3.5.1 Routing Mode .......................................................................................................... 37 3.5.2 Dynamic Routing (RIP) .......................................................................................... 39 3.5.3 Static Routing .......................................................................................................... 40 3.6 Configurable Port - WAN Option .......................................................................... 42 3.7 WAN Port Settings .................................................................................................. 44 Chapter 4. Wireless Access Point Setup ............................................................................................. 46 4.1 Wireless Settings Wizard ....................................................................................... 46 4.1.1 Wireless Network Setup Wizard ........................................................................... 47 4.1.2 Add Wireless Device with WPS ............................................................................ 47 4.1.3 Manual Wireless Network Setup .......................................................................... 48 4.2 Wireless Profiles ..................................................................................................... 48 4.2.1 WEP Security .......................................................................................................... 49 4.2.2 WPA or WPA2 with PSK ........................................................................................ 50 4.2.3 RADIUS Authentication .......................................................................................... 51 4.3 Creating and Using Access Points ....................................................................... 52 4.3.1 Primary benefits of Virtual APs: ............................................................................ 54 4.4 Tuning Radio Specific Settings ............................................................................. 55 4.5 Advanced Wireless Settings .................................................................................. 56
Unified Services Router User Manual 3 4.6 Wi-Fi Protected Setup (WPS) ............................................................................... 56 Chapter 5. Securing the Private Network ............................................................................................ 59 5.1 Firewall Rules .......................................................................................................... 59 5.2 Defining Rule Schedules ....................................................................................... 60 5.3 Configuring Firewall Rules ..................................................................................... 61 5.3.1 Firewall Rule Configuration Examples ................................................................. 65 5.4 Security on Custom Services ................................................................................ 68 5.5 ALG support ............................................................................................................. 69 5.6 VPN Passthrough for Firewall ............................................................................... 70 5.7 Application Rules .................................................................................................... 71 5.8 Web Content Filtering ............................................................................................. 72 5.9 IP/MAC Binding ....................................................................................................... 75 5.10 Intrusion Prevention (IPS)...................................................................................... 76 5.10.1 Protecting from Internet Attacks ........................................................................... 77 Chapter 6. IPSec / PPTP / L2TP VPN ................................................................................................. 79 6.1 VPN Wizard ............................................................................................................. 79 6.2 Configuring IPSec Policies .................................................................................... 82 6.2.1 Extended Authentication (XAUTH) ....................................................................... 85 6.3 Configuring VPN clients ......................................................................................... 85 6.4 PPTP / L2TP Tunnels ............................................................................................. 86 6.4.1 PPTP Tunnel Support ............................................................................................ 86 6.4.2 L2TP Tunnel Support ............................................................................................. 87 Chapter 7. SSL VPN ............................................................................................................................... 89 7.1 Users, Groups, and Domains ................................................................................ 89 7.1.1 User Types and Passwords .................................................................................. 90 7.2 Using SSL VPN Policies ........................................................................................ 92 7.2.1 Using Network Resources ..................................................................................... 94 7.3 Application Port Forwarding .................................................................................. 95 7.4 SSL VPN Client Configuration .............................................................................. 96 7.5 User Portal ............................................................................................................... 98 7.5.1 Creating Portal Layouts ......................................................................................... 99 Chapter 8. Advanced Configuration Tools ......................................................................................... 101 8.1 USB Device Setup ................................................................................................ 101 8.2 Authentication Certificates ................................................................................... 101 Chapter 9. Administration & Management ......................................................................................... 103 9.1 Configuration Access Control .............................................................................. 103 9.1.1 Remote Management ........................................................................................... 103 9.1.2 CLI Access ............................................................................................................. 104 9.2 SNMP Configuration ............................................................................................. 104 9.3 Configuring Time Zone and NTP ........................................................................ 106 9.4 Log Configuration .................................................................................................. 107 9.4.1 Defining What to Log ............................................................................................ 107
Unified Services Router User Manual 4 9.4.2 Sending Logs to E-mail or Syslog ...................................................................... 111 9.4.3 Event Log Viewer in GUI ..................................................................................... 113 9.5 Backing up and Restoring Configuration Settings ........................................... 114 9.6 Upgrading Router Firmware ................................................................................ 115 9.7 Dynamic DNS Setup ............................................................................................. 116 9.8 Using Diagnostic Tools ........................................................................................ 117 9.8.1 Ping ......................................................................................................................... 118 9.8.2 Trace Route ........................................................................................................... 118 9.8.3 DNS Lookup .......................................................................................................... 119 9.8.4 Router Options ...................................................................................................... 119 Chapter 10. Router Status and Statistics ............................................................................................. 120 10.1 System Overview .................................................................................................. 120 10.1.1 Device Status ........................................................................................................ 120 10.1.2 Resource Utilization .............................................................................................. 122 10.2 Traffic Statistics ..................................................................................................... 126 10.2.1 Wired Port Statistics ............................................................................................. 126 10.2.2 Wireless Statistics ................................................................................................. 127 10.3 Active Connections ............................................................................................... 128 10.3.1 Sessions through the Router ............................................................................... 128 10.3.2 Wireless Clients..................................................................................................... 130 10.3.3 LAN Clients ............................................................................................................ 130 10.3.4 Active VPN Tunnels .............................................................................................. 131 Chapter 11. Trouble Shooting ................................................................................................................ 133 11.1 Internet connection ............................................................................................... 133 11.2 Date and time ........................................................................................................ 135 11.3 Pinging to Test LAN Connectivity ....................................................................... 135 11.3.1 Testing the LAN path from your PC to your router .......................................... 135 11.3.2 Testing the LAN path from your PC to a remote device ................................. 136 11.4 Restoring factory-default configuration settings ............................................... 137 Chapter 12. Credits ................................................................................................................................. 139 Appendix A. Glossary .............................................................................................................................. 140 Appendix B. Factory Default Settings ................................................................................................... 143 Appendix C. Standard Services Available for Port Forwarding & Firewall Configuration .............. 144 Appendix D. Log Output Reference ....................................................................................................... 145
Unified Services Router User Manual 5 List of Figures Figure 1: Setup page for LAN TCP/IP settings ...................................................................................... 11 Figure 2: IPv6 LAN and DHCPv6 configuration ..................................................................................... 13 Figure 3: Configuring the Router Advertisement Daemon ................................................................... 16 Figure 4: IPv6 Advertisement Prefix settings ......................................................................................... 17 Figure 5: Adding VLAN memberships to the LAN ................................................................................. 18 Figure 6: Port VLAN list ............................................................................................................................. 19 Figure 7: Configuring VLAN membership for a port .............................................................................. 20 Figure 8: DMZ configuration ..................................................................................................................... 21 Figure 9: UPnP Configuration ................................................................................................................... 22 Figure 10: Internet Connection Setup Wizard ........................................................................................ 23 Figure 11: Manual WAN configuration .................................................................................................... 26 Figure 12: List of configured PPPoE profiles .......................................................................................... 27 Figure 13: PPPoE profile configuration ................................................................................................... 28 Figure 14: IPv6 WAN Setup page ............................................................................................................ 29 Figure 15: Connection Status information for both WAN ports ............................................................ 31 Figure 16: List of Configured Bandwidth Profiles ................................................................................... 32 Figure 17: Bandwidth Profile Configuration page .................................................................................. 33 Figure 18: Traffic Selector Configuration ................................................................................................ 34 Figure 19: Load Balancing is available when multiple WAN ports are configured and Protocol Bindings have been defined ................................................................................................... 36 Figure 20: Protocol binding setup to associate a service and/or LAN source to a WAN and/or destination network .................................................................................................................. 37 Figure 21: Routing Mode is used to configure traffic routing between WAN and LAN, as well as Dynamic routing (RIP) ............................................................................................................. 39 Figure 22: Static route configuration fields ............................................................................................. 42 Figure 23: WAN2 configuration for 3G internet (part 1) ........................................................................ 43 Figure 24: WAN2 configuration for 3G internet (part 2) ........................................................................ 44 Figure 25: Physical WAN port settings .................................................................................................... 45 Figure 26: Wireless Network Setup Wizards .......................................................................................... 47 Figure 27: List of Available Profiles shows the variety of options available to secure the wireless link .............................................................................................................................................. 49 Figure 28: Profile configuration to set network security ........................................................................ 50 Figure 29: RADIUS server (External Authentication) configuration .................................................... 52 Figure 30: Virtual AP configuration .......................................................................................................... 53 Figure 31: List of configured access points (Virtual APs) shows one enabled access point on the radio, broadcasting its SSID ................................................................................................... 54
Unified Services Router User Manual 6 Figure 32: Radio card configuration options ........................................................................................... 55 Figure 33: Advanced Wireless communication settings ....................................................................... 56 Figure 34: WPS configuration for an AP with WPA/WPA2 profile ....................................................... 57 Figure 35: List of Available Firewall Rules .............................................................................................. 60 Figure 36: List of Available Schedules to bind to a firewall rule .......................................................... 61 Figure 37: The firewall rule configuration page allows you to define the To/From zone, service, action, schedules, and specify source/destination IP addresses as needed. ................. 64 Figure 38: Schedule configuration for the above example. .................................................................. 67 Figure 39: List of user defined services. ................................................................................................. 69 Figure 40: Available ALG support on the router..................................................................................... 70 Figure 41: Passthrough options for VPN tunnels ................................................................................... 71 Figure 42: List of Available Application Rules showing 4 unique rules .............................................. 72 Figure 43: Content Filtering used to block access to proxy servers and prevent ActiveX controls from being downloaded ........................................................................................................... 73 Figure 44: Two trusted domains added to the Approved URLs List ................................................... 74 Figure 45: Two keywords added to the block list ................................................................................... 75 Figure 46: The above example of IP/MAC Binding binds a LAN host’s MAC Address to an IP address. If there is an IP/MAC Binding violation, the violating packet will be dropped and logs will be captured ........................................................................................................ 76 Figure 47: Intrusion Prevention features on the router ......................................................................... 77 Figure 48: Protecting the router and LAN from internet attacks .......................................................... 78 Figure 49: VPN Wizard launch screen .................................................................................................... 80 Figure 50: IPSec policy configuration ...................................................................................................... 83 Figure 51: IPSec policy configuration continued (Auto policy via IKE) ............................................... 84 Figure 52: IPSec policy configuration continued (Auto / Manual Phase 2) ........................................ 85 Figure 53: PPTP tunnel configuration – PPTP Server .......................................................................... 87 Figure 54: L2TP tunnel configuration – L2TP Server ............................................................................ 87 Figure 55: Available Users with login status and associated Group/Domain .................................... 90 Figure 56: User configuration options ...................................................................................................... 92 Figure 57: List of SSL VPN polices (Global filter) .................................................................................. 93 Figure 58: SSL VPN policy configuration ................................................................................................ 94 Figure 59: List of configured resources, which are available to assign to SSL VPN policies ......... 95 Figure 60: List of Available Applications for SSL Port Forwarding ...................................................... 96 Figure 61: SSL VPN client adapter and access configuration ............................................................. 97 Figure 62: Configured client routes only apply in split tunnel mode.................................................... 98 Figure 63: List of configured SSL VPN portals. The configured portal can then be associated with an authentication domain ........................................................................................................ 99
Unified Services Router User Manual 7 Figure 64: SSL VPN Portal configuration .............................................................................................. 100 Figure 65: USB device configuration ..................................................................................................... 101 Figure 66: Certificate summary for IPSec and HTTPS management ............................................... 102 Figure 67: User Login policy configuration ........................................................................................... 103 Figure 68: Remote Management from the WAN.................................................................................. 104 Figure 69: SNMP Users, Traps, and Access Control .......................................................................... 105 Figure 70: SNMP system information for this router ........................................................................... 106 Figure 71: Date, Time, and NTP server setup ..................................................................................... 107 Figure 72: Facility settings for Logging .................................................................................................. 109 Figure 73: Log configuration options for traffic through router ........................................................... 111 Figure 74: E-mail configuration as a Remote Logging option ............................................................ 112 Figure 75: Syslog server configuration for Remote Logging (continued) ......................................... 113 Figure 76: VPN logs displayed in GUI event viewer ............................................................................ 114 Figure 77: Restoring configuration from a saved file will result in the current configuration being overwritten and a reboot ....................................................................................................... 115 Figure 78: Firmware version information and upgrade option ........................................................... 116 Figure 79: Dynamic DNS configuration ................................................................................................. 117 Figure 80: Router diagnostics tools available in the GUI .................................................................... 118 Figure 81: Sample traceroute output ..................................................................................................... 119 Figure 82: Device Status display ............................................................................................................ 121 Figure 83: Device Status display (continued) ....................................................................................... 122 Figure 84: Resource Utilization statistics .............................................................................................. 123 Figure 85: Resource Utilization data (continued) ................................................................................. 125 Figure 86: Resource Utilization data (continued) ................................................................................. 126 Figure 87: Physical port statistics ........................................................................................................... 127 Figure 88: AP specific statistics .............................................................................................................. 128 Figure 89: List of current Active Firewall Sessions .............................................................................. 129 Figure 90: List of connected 802.11 clients per AP ............................................................................. 130 Figure 91: List of LAN hosts .................................................................................................................... 131 Figure 92: List of current Active VPN Sessions ................................................................................... 132
Unified Services Router User Manual 8 Chapter 1. Introduction The D-Link Unified Services Routers are enterprise grade security gateway solutions with Firewall, VPN and in some cases 802.11n Access Point capabilities. These devices have wizards to allow for quick and easy configuration for internet access, VPN tunnels, and wireless networks. The GUI provides all the capabilities for novice and advanced users to administer this secure and feature rich router. 1.1 About this User Manual This document is a high level manual to allow new D-Link Unified Services Router users to configure connectivity, setup VPN tunnels, establish firewall rules and perform general administrative tasks. Typical deployment and use case scenarios are described in each section. For more detailed setup instructions and explanations of each configuration parameter, refer to the online help that can be accessed from each page in the router GUI. 1.2 Typographical Conventions The following is a list of the various terms, followed by an example of how that term is represented in this document: • Product Name – D-Link Unified Services Router. • Model numbers DSR-500/500N/1000/1000N • GUI Menu Path/GUI Navigation – Monitoring > Router Status • User input – Text • Important note – 
Chapter 2. Configuring Your Network: LAN Setup It is assumed that the user has a machine for management connected to the LAN to the router. The LAN connection may be through the wired Ethernet ports available on the router, or once the initial setup is complete, the device may also be managed through its wireless interface as it is bridged with the LAN. Access the router’s graphical user interface (GUI) for management by using any web browser, such as Microsoft Internet Explorer or Mozilla Firefox: • Go to http://192.168.10.1 (default IP address) to display the router’s management login screen. • Default login credentials for the management GUI: • Username: admin • Password: admin  If the router’s LAN IP address was changed, use that IP address in the navigation bar of the browser to access the router’s management UI. 2.1 LAN Configuration Setup > Network Settings > LAN Configuration By default, the router functions as a Dynamic Host Configuration Protocol (DHCP) server to the hosts on the WLAN or LAN network. With DHCP, PCs and other LAN devices can be assigned IP addresses as well as addresses for DNS servers, Windows Internet Name Service (WINS) servers, and the default gateway. With the DHCP server enabled the router’s IP address serves as the gateway address for LAN and WLAN clients. The PCs in the LAN are assigned IP addresses from a pool of addresses specified in this procedure. Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN. For most applications the default DHCP and TCP/IP settings are satisfactory. If you want another PC on your network to be the DHCP server or if you are manually configuring the network settings of all of your PCs, set the DHCP mode to ‘none’. DHCP relay can be used to forward DHCP lease information from another LAN device that is the network’s DHCP server; this is particularly useful for wireless clients. Instead of using a DNS server, you can use a Windows Internet Naming Service (WINS) server. A WINS server is the equivalent of a DNS server but uses the NetBIOS protocol to resolve hostnames. The router includes the WINS server IP address in the DHCP configuration when acknowledging a DHCP request from a DHCP client. You can also enable DNS proxy for the LAN. When this is enabled the router then as a proxy for all DNS requests and communicates with the ISP’s DNS servers. When disabled all DHCP clients receive the DNS IP addresses of the ISP.
Unified Services Router User Manual 10 To configure LAN Connectivity, please follow the steps below: 1. In the LAN Setup page, enter the following information for your router: • IP address (factory default: 192.168.10.1).  If you change the IP address and click Save Settings, the GUI will not respond. Open a new connection to the new IP address and log in again. Be sure the LAN host (the machine used to manage the router) has obtained IP address from newly assigned pool (or has a static IP address in the router’s LAN subnet) before accessing the router via changed IP address. • Subnet mask (factory default: 255.255.255.0). 2. In the DHCP section, select the DHCP mode: • None: the router’s DHCP server is disabled for the LAN • DHCP Server. With this option the router assigns an IP address within the specified range plus additional specified information to any LAN device that requests DHCP served addresses. • DHCP Relay: With this option enabled, DHCP clients on the LAN can receive IP address leases and corresponding information from a DHCP server on a different subnet. Specify the Relay Gateway, and when LAN clients make a DHCP request it will be passed along to the server accessible via the Relay Gateway IP address. • If DHCP is being enabled, enter the following DHCP server parameters: • Starting and Ending IP Addresses: Enter the first and last continuous addresses in the IP address pool. Any new DHCP client joining the LAN is assigned an IP address in this range. The default starting address is 192.168.10.2. The default ending address is 192.168.10.100. These addresses should be in the same IP address subnet as the router’s LAN IP address. You may wish to save part of the subnet range for devices with statically assigned IP addresses in the LAN. • Primary and Secondary DNS servers: If configured domain name system (DNS) servers are available on the LAN enter their IP addresses here. • WINS Server (optional): Enter the IP address for the WINS server or, if present in your network, the Windows NetBios server. • Lease Time: Enter the time, in hours, for which IP addresses are leased to clients.
Unified Services Router User Manual 11 • Enable DNS Proxy: To enable the router to act as a proxy for all DNS requests and communicate with the ISP’s DNS servers, click the checkbox. 3. Click Save Settings to apply all changes. Figure 1: Setup page for LAN TCP/IP settings 2.1.1 LAN Configuration in an IPv6 Network Advanced > IPv6 > IPv6 LAN > IPv6 LAN Config In IPv6 mode, the LAN DHCP server is enabled by default (similar to IPv4 mode). The DHCPv6 server will serve IPv6 addresses from configured address pools with the IPv6 Prefix Length assigned to the LAN.
Unified Services Router User Manual 12  IPv4 / IPv6 mode must be enabled in the Advanced > IPv6 > IP mode to enable IPv6 configuration options. LAN Settings The default IPv6 LAN address for the router is fec0::1. You can change this 128 bit IPv6 address based on your network requirements. The other field that defines the LAN settings for the router is the prefix length. The IPv6 network (subnet) is identified by the initial bits of the address called the prefix. By default this is 64 bits long. All hosts in the network have common initial bits for their IPv6 address; the number of common initial bits in the network’s addresses is set by the prefix length field.
Unified Services Router User Manual 13 Figure 2: IPv6 LAN and DHCPv6 configuration  If you change the IP address and click Save Settings, the GUI will not respond. Open a new connection to the new IP address and log in again. Be sure the LAN host (the machine used to manage the router) has obtained IP address from newly assigned pool (or has a static IP address in the router’s LAN subnet) before accessing the router via changed IP address. As with an IPv4 LAN network, the router has a DHCPv6 server. If enabled, the router assigns an IP address within the specified range plus additional specified information to any LAN PC that requests DHCP served addresses. The following settings are used to configure the DHCPv6 server:
Unified Services Router User Manual 14 • DHCP Mode: The IPv6 DHCP server is either stateless or stateful. If stateless is selected an external IPv6 DHCP server is not required as the IPv6 LAN hosts are auto-configured by this router. In this case the router advertisement daemon (RADVD) must be configured on this device and ICMPv6 router discovery messages are used by the host for auto-configuration. There are no managed addresses to serve the LAN nodes. If stateful is selected the IPv6 LAN host will rely on an external DHCPv6 server to provide required configuration settings • The domain name of the DHCPv6 server is an optional setting • Server Preference is used to indicate the preference level of this DHCP server. DHCP advertise messages with the highest server preference value to a LAN host are preferred over other DHCP server advertise messages. The default is 255. • The DNS server details can be manually entered here (primary/secondary options. An alternative is to allow the LAN DHCP client to receive the DNS server details from the ISP directly. By selecting Use DNS proxy, this router acts as a proxy for all DNS requests and communicate with the ISP’s DNS servers (a WAN configuration parameter). • Primary and Secondary DNS servers: If there are configured domain name system (DNS) servers available on the LAN enter the IP addresses here. • Lease/Rebind time sets the duration of the DHCPv6 lease from this router to the LAN client. IPv6 Address Pools This feature allows you to define the IPv6 delegation prefix for a range of IP addresses to be served by the gateway’s DHCPv6 server. Using a delegation prefix you can automate the process of informing other networking equipment on the LAN of DHCP information specific for the assigned prefix. 2.1.2 Configuring IPv6 Router Advertisements Router Advertisements are analogous to IPv4 DHCP assignments for LAN clients, in that the router will assign an IP address and supporting network information to devices that are configured to accept such details. Router Advertisement is required in an IPv6 network is required for stateless auto configuration of the IPv6 LAN. By configuring the Router Advertisement Daemon on this router, the device will listen on the LAN for router solicitations and respond to these LAN hosts with router advisements.
Unified Services Router User Manual 15 RADVD Advanced > IPv6 > IPv6 LAN > Router Advertisement To support stateless IPv6 auto configuration on the LAN, set the RADVD status to Enable. The following settings are used to configure RADVD: • Advertise Mode: Select Unsolicited Multicast to send router advertisements (RA’s) to all interfaces in the multicast group. To restrict RA’s to well known IPv6 addresses on the LAN, and thereby reduce overall network traffic, select Unicast only. • Advertise Interval: When advertisements are unsolicited multicast packets, this interval sets the maximum time between advertisements from the interface. The actual duration between advertisements is a random value between one third of this field and this field. The default is 30 seconds. • RA Flags: The router advertisements (RA’s) can be sent with one or both of these flags. Chose Managed to use the administered /stateful protocol for address auto configuration. If the Other flag is selected the host uses administered/stateful protocol for non-address auto configuration. • Router Preference: this low/medium/high parameter determines the preference associated with the RADVD process of the router. This is useful if there are other RADVD enabled devices on the LAN as it helps avoid conflicts for IPv6 clients. • MTU: The router advertisement will set this maximum transmission unit (MTU) value for all nodes in the LAN that are autoconfigured by the router. The default is 1500. • Router Lifetime: This value is present in RA’s and indicates the usefulness of this router as a default router for the interface. The default is 3600 seconds. Upon expiration of this value, a new RADVD exchange must take place between the host and this router.
Unified Services Router User Manual 16 Figure 3: Configuring the Router Advertisement Daemon Advertisement Prefixes Advanced > IPv6 > IPv6 LAN > Advertisement Prefixes The router advertisements configured with advertisement prefixes allow this router to inform hosts how to perform stateless address auto configuration. Router advertisements contain a list of subnet prefixes that allow the router to determine neighbors and whether the host is on the same link as the router. The following prefix options are available for the router advertisements: • IPv6 Prefix Type: To ensure hosts support IPv6 to IPv4 tunnel select the 6to4 prefix type. Selecting Global/Local/ISATAP will allow the nodes to support all other IPv6 routing options • SLA ID: The SLA ID (Site-Level Aggregation Identifier) is available when 6to4 Prefixes are selected. This should be the interface ID of the router’s LAN interface used for router advertisements. • IPv6 Prefix: When using Global/Local/ISATAP prefixes, this field is used to define the IPv6 network advertised by this router.
Unified Services Router User Manual 17 • IPv6 Prefix Length: This value indicates the number contiguous, higher order bits of the IPv6 address that define up the network portion of the address. Typically this is 64. • Prefix Lifetime: This defines the duration (in seconds) that the requesting node is allowed to use the advertised prefix. It is analogous to DHCP lease time in an IPv4 network. Figure 4: IPv6 Advertisement Prefix settings 2.2 VLAN Configuration The router supports virtual network isolation on the LAN with the use of VLANs. LAN devices can be configured to communicate in a subnetwork defined by VLAN identifiers. LAN ports can be assigned unique VLAN IDs so that traffic to and from that physical port can be isolated from the general LAN. VLAN filtering is particularly useful to limit broadcast packets of a device in a large network VLAN support is disabled by default in the router. In the VLAN Configuration page, enable VLAN support on the router and then proceed to the next section to define the virtual network. Setup > VLAN Settings > Available VLAN The Available VLAN page shows a list of configured VLANs by name and VLAN ID. A VLAN membership can be created by clicking the Add button below the List of Available VLANs. A VLAN membership entry consists of a VLAN identifier and the numerical VLAN ID which is assigned to the VLAN membership. The VLAN ID value can be any number from 2 to 4091. VLAN ID 1 is reserved for the default VLAN, which is used for untagged frames received on the interface. By enabling Inter VLAN Routing, you
Unified Services Router User Manual 18 will allow traffic from LAN hosts belonging to this VLAN ID to pass through to other configured VLAN IDs that have Inter VLAN Routing enabled. Figure 5: Adding VLAN memberships to the LAN 2.2.1 Associating VLANs to ports In order to tag all traffic through a specific LAN port with a VLAN ID, you can associate a VLAN to a physical port. Setup > VLAN Settings > Port VLAN VLAN membership properties for the LAN and wireless LAN are listed on this page. The VLAN Port table displays the port identifier, the mode setting for that port and VLAN membership information. The configuration page is accessed by selecting one of the four physical ports or a configured access point and clicking Edit. The edit page offers the following configuration options: • Mode: The mode of this VLAN can be General, Access, or Trunk. The default is access. • In General mode the port is a member of a user selectable set of VLANs. The port sends and receives data that is tagged or untagged with a VLAN ID. If the data into the port is untagged, it is assigned the defined PVID. In the configuration from Figure 4, Port 3 is a General port with PVID 3, so untagged data into Port 3 will be assigned PVID 3. All tagged data sent out of the port with the same PVID will be untagged. This is mode is typically used with IP Phones that have dual Ethernet ports. Data coming from phone to the switch port on the router will be tagged. Data passing through the phone from a connected device will be untagged.
Unified Services Router User Manual 19 Figure 6: Port VLAN list • In Access mode the port is a member of a single VLAN (and only one). All data going into and out of the port is untagged. Traffic through a port in access mode looks like any other Ethernet frame. • In Trunk mode the port is a member of a user selectable set of VLANs. All data going into and out of the port is tagged. Untagged coming into the port is not forwarded, except for the default VLAN with PVID=1, which is untagged. Trunk ports multiplex traffic for multiple VLANs over the same physical link. • Select PVID for the port when the General mode is selected. • Configured VLAN memberships will be displayed on the VLAN Membership Configuration for the port. By selecting one more VLAN membership options for a General or Trunk port, traffic can be routed between the selected VLAN membership IDs
Unified Services Router User Manual 20 Figure 7: Configuring VLAN membership for a port 2.3 Configurable Port: DMZ Setup This router supports one of the physical ports to be configured as a secondary WAN Ethernet port or a dedicated DMZ port. A DMZ is a subnetwork that is open to the public but behind the firewall. The DMZ adds an additional layer of security to the LAN, as specific services/ports that are exposed to the internet on the DMZ do not have to be exposed on the LAN. It is recommended that hosts that must be exposed to the internet (such as web or email servers) be placed in the DMZ network. Firewall rules can be allowed to permit access specific services/ports to the DMZ from both the LAN or WAN. In the event of an attack to any of the DMZ nodes, the LAN is not necessarily vulnerable as well. Setup > DMZ Setup > DMZ Setup Configuration DMZ configuration is identical to the LAN configuration. There are no restrictions on the IP address or subnet assigned to the DMZ port, other than the fact that it cannot be identical to the IP address given to the LAN interface of this gateway.
Unified Services Router User Manual 21 Figure 8: DMZ configuration  In order to configure a DMZ port, the router’s configurable port must be set to DMZ in the Setup > Internet Settings > Configurable Port page. 2.4 Universal Plug and Play (UPnP) Advanced > Advanced Network > UPnP Universal Plug and Play (UPnP) is a feature that allows the router to discovery devices on the network that can communicate with the router and allow for auto configuration. If a network device is detected by UPnP, the router can open internal or external ports for the traffic protocol required by that network device. Once UPnP is enabled, you can configure the router to detect UPnP-supporting devices on the LAN (or a configured VLAN). If disabled, the router will not allow for automatic device configuration. Configure the following settings to use UPnP:
Unified Services Router User Manual 22 • Advertisement Period: This is the frequency that the router broadcasts UPnP information over the network. A large value will minimize network traffic but cause delays in identifying new UPnP devices to the network. • Advertisement Time to Live: This is expressed in hops for each UPnP packet. This is the number of steps a packet is allowed to propagate before being discarded. Small values will limit the UPnP broadcast range. A default of 4 is typical for networks with few switches. Figure 9: UPnP Configuration UPnP Port map Table The UPnP Port map Table has the details of UPnP devices that respond to the router’s advertisements. The following information is displayed for each detected device: • Active: A yes/no indicating whether the port of the UPnP device that established a connection is currently active • Protocol: The network protocol (i.e. HTTP, FTP, etc.) used by the device • Int. Port (Internal Port): The internal ports opened by UPnP (if any) • Ext. Port (External Port): The external ports opened by UPnP (if any) • IP Address: The IP address of the UPnP device detected by this router Click Refresh to refresh the portmap table and search for any new UPnP devices.
Unified Services Router User Manual 23 Chapter 3. Connecting to the Internet: WAN Setup This router has two WAN ports that can be used to establish a connection to the internet. The following ISP connection types are supported: DHCP, Static, PPPoE, PPTP, L2TP, 3G Internet (via USB modem). It is assumed that you have arranged for internet service with your Internet Service Provider (ISP). Please contact your ISP or network administrator for the configuration information that will be required to setup the router. 3.1 Internet Setup Wizard Setup > Wizard > Internet The Internet Connection Setup Wizard is available for users new to networking. By going through a few straightforward configuration pages you can take the information provided by your ISP to get your WAN connection up and enable internet access for your network. Figure 10: Internet Connection Setup Wizard You can start using the Wizard by logging in with the administrator password for the router. Once authenticated set the time zone that you are located in, and then choose the type of ISP connection type: DHCP, Static, PPPoE, PPTP, L2TP. Depending on the connection type a username/password may be required to register this router with the ISP. In most cases the default settings can be used if the ISP did not specify that parameter. The last step in the Wizard is to click the Connect button, which confirms the settings by establishing a link with the ISP. Once connected, you can move on and configure other features in this router.
Unified Services Router User Manual 24  3G Internet access with a USB modem is supported on the secondary WAN port (WAN2). The Internet Connection Setup Wizard assists with the primary WAN port (WAN1) configuration only. 3.2 WAN Configuration Setup > Internet Settings > WAN1 Setup You must either allow the router to detect WAN connection type automatically or configure manually the following basic settings to enable Internet connectivity: • ISP Connection type: Based on the ISP you have selected for the primary WAN link for this router, choose Static IP address, DHCP client, Point-to-Point Tunneling Protocol (PPTP), Point-to-Point Protocol over Ethernet (PPPoE), Layer 2 Tunneling Protocol (L2TP). Required fields for the selected ISP type become highlighted. Enter the following information as needed and as provided by your ISP: • PPPoE Profile Name. This menu lists configured PPPoE profiles, particularly useful when configuring multiple PPPoE connections (i.e. for Japan ISPs that have multiple PPPoE support). • ISP login information. This is required for PPTP and L2TP ISPs. • User Name • Password • Secret (required for L2TP only) • MPPE Encryption: For PPTP links, your ISP may require you to enable Microsoft Point-to-Point Encryption (MPPE). • Split Tunnel (supported for PPTP and L2TP connection). This setting allows your LAN hosts to access internet sites over this WAN link while still permitting VPN traffic to be directed to a VPN configured on this WAN port.  With split tunneling enabled users can bypass content filtering and other firewall settings. Disable split tunneling on the WAN interface for highest gateway security measures. • Connectivity Type. To keep the connection always on, click Keep Connected. To log out after the connection is idle for a period of time (useful if your ISP costs are based on logon times), click Idle Timeout and enter the time, in minutes, to wait before disconnecting in the Idle Time field. • My IP Address: Enter the IP address assigned to you by the ISP.
Unified Services Router User Manual 25 • Server IP Address: Enter the IP address of the PPTP or L2TP server. 3.2.1 WAN Port IP address Your ISP assigns you an IP address that is either dynamic (newly generated each time you log in) or static (permanent). The IP Address Source option allows you to define whether the address is statically provided by the ISP or should be received dynamically at each login. If static, enter your IP address, IPv4 subnet mask, and the ISP gateway’s IP address. PPTP and L2TP ISPs also can provide a static IP address and subnet to configure, however the default is to receive that information dynamically from the ISP. 3.2.2 WAN DNS Servers The IP Addresses of WAN Domain Name Servers (DNS) are typically provided dynamically from the ISP but in some cases you can define the static IP addresses of the DNS servers. DNS servers map Internet domain names (example: www.google.com) to IP addresses. Click to indicate whether to get DNS server addresses automatically from your ISP or to use ISP-specified addresses. If the latter, enter addresses for the primary and secondary DNS servers. To avoid connectivity problems, ensure that you enter the addresses correctly. 3.2.3 DHCP WAN For DHCP client connections, you can choose the MAC address of the router to register with the ISP. In some cases you may need to clone the LAN host’s MAC address if the ISP is registered with that LAN host.
Unified Services Router User Manual 26 Figure 11: Manual WAN configuration
Unified Services Router User Manual 27 3.2.4 PPPoE Profiles Setup > Internet Settings > PPPoE Profiles > WAN1 PPPoE Profiles Some ISP’s allow for multiple concurrent PPPoE sessions (it is most common in Japan). Each connection can have its own specific authentication requirements and will provide unique IP, gateway, and DNS address parameters to the associated WAN port. The PPPoE Profiles page offers a convenient way to maintain multiple PPPoE accounts, which can then be associated with one of the available WAN interfaces. Once configured, a PPPoE profile name can be selected on the WAN configuration page to reduce the configuration requirements for that WAN port. The PPPoE profile is referenced on the WAN Configuration page. The List of PPPoE profiles for a particular WAN (see figure below) outlines the available profile and their status and authentication type. Figure 12: List of configured PPPoE profiles To create a new PPPoE profile, select Add in the PPPoE Profile page. Each profile is associated to one of the two WAN ports. Similar to the PPPoE configuration options in the WAN configuration page, you need to define the ISP logon credentials, authentication type, and connectivity settings for the PPPoE session. This information will be provided by the ISP that offers multiple PPPoE session support.
Unified Services Router User Manual 28 Figure 13: PPPoE profile configuration 3.2.5 WAN Configuration in an IPv6 Network Setup > IPv6 > IPv6 WAN1 Config For IPv6 WAN connections, this router can have a static IPv6 address or receive connection information when configured as a DHCPv6 client. In the case where the ISP assigns you a fixed address to access the internet, the static configuration settings must be completed. In addition to the IPv6 address assigned to your router, the IPv6 prefix length defined by the ISP is needed. The default IPv6 Gateway address is the server at the ISP that this router will connect to for accessing the internet. The primary and secondary DNS servers on the ISP’s IPv6 network are used for resolving internet addresses, and these are provided along with the static IP address and prefix length from the ISP.
Unified Services Router User Manual 29 When the ISP allows you to obtain the WAN IP settings via DHCP, you need to provide details for the DHCPv6 client configuration. The DHCPv6 client on the gateway can be either stateless or stateful. If a stateful client is selected the gateway will connect to the ISP’s DHCPv6 server for a leased address. For stateless DHCP there need not be a DHCPv6 server available at the ISP, rather ICMPv6 discover messages will originate from this gateway and will be used for auto configuration. A third option to specify the IP address and prefix length of a preferred DHCPv6 server is available as well. Figure 14: IPv6 WAN Setup page 3.2.6 Checking WAN Status Setup > Internet Settings > WAN Status The status and summary of configured settings for both WAN1 and WAN2 are available on the WAN Status page. You can view the following key connection status information for each WAN port: • Connection time • Connection type: dynamic IP or static IP
Unified Services Router User Manual 30 • Connection state: This is whether the WAN is connected or disconnected to an ISP. The Link State is whether the physical WAN connection in place; the Link State can be UP (i.e. cable inserted) while the WAN Connection State is down. • IP address / subnet mask • Gateway IP address
Unified Services Router User Manual 31 Figure 15: Connection Status information for both WAN ports The WAN status page allows you to Enable or Disable static WAN links. For WAN settings that are dynamically received from the ISP, you can Renew or Release the link parameters if required.
Unified Services Router User Manual 32 3.3 Bandwidth Controls Advanced > Advanced Network > Traffic Management > Bandwidth Profiles Bandwidth profiles allow you to regulate the traffic flow from the LAN to WAN 1 or WAN 2. This is useful to ensure that low priority LAN users (like guests or HTTP service) do not monopolize the available WAN’s bandwidth for cost-savings or bandwidth-priority-allocation purposes. Bandwidth profiles configuration consists of enabling the bandwidth control feature from the GUI and adding a profile which defines the control parameters. The profile can then be associated with a traffic selector, so that bandwidth profile can be applied to the traffic matching the selectors. Selectors are elements like IP addresses or services that would trigger the configured bandwidth regulation. Figure 16: List of Configured Bandwidth Profiles To create a new bandwidth profile, click Add in the List of Bandwidth Profiles. The following configuration parameters are used to define a bandwidth profile: • Profile Name: This identifier is used to associate the configured profile to the traffic selector • You can choose to limit the bandwidth either using priority or rate. • If using priority “Low”, “High”, “Medium” can be selected. If there is a low priority profile associated with traffic selector A and a high priority profile associated with traffic selector B, then the WAN bandwidth allocation preference will be to traffic selector B packets.
Unified Services Router User Manual 33 • For finer control, the Rate profile type can be used. With this option the minimum and maximum bandwidth allowed by this profile can be limited. • Choose the WAN interface that the profile should be associated with Figure 17: Bandwidth Profile Configuration page Advanced > Advanced Network > Traffic Management > Traffic Selectors Once a profile has been created it can then be associated with a traffic flow from the LAN to WAN. To create a traffic selector, click Add on the Traffic Selectors page. Traffic selector configuration binds a bandwidth profile to a type or source of LAN traffic with the following settings: • Available profiles: Assign one of the defined bandwidth profiles • Service: You can have the selected bandwidth regulation apply to a specific service (i.e. FTP) from the LAN. If you do not see a service that you want, you can configure a custom service through the Advanced > Firewall Settings > Custom Services page. To have the profile apply to all services, select ANY. • Traffic Selector Match Type: this defines the parameter to filter against when applying the bandwidth profile. A specific machine on the LAN can be identified via IP address or MAC address, or the profile can apply to a LAN port or VLAN group. As well a wireless network can be selected by its BSSID for bandwidth shaping.
Unified Services Router User Manual 34 Figure 18: Traffic Selector Configuration 3.4 Features with Multiple WAN Links This router supports multiple WAN links. This allows you to take advantage of failover and load balancing features to ensure certain internet dependent services are prioritized in the event of unstable WAN connectivity on one of the ports. Setup > Internet Settings > WAN Mode To use Auto Failover or Load Balancing, WAN link failure detection must be configured. This involves accessing DNS servers on the internet or ping to an internet address (user defined). If required, you can configure the number of retry attempts when the link seems to be disconnected or the threshold of failures that determines if a WAN port is down. 3.4.1 Auto Failover In this case one of your WAN ports is assigned as the primary internet link for all internet traffic. The secondary WAN port is used for redundancy in case the primary link goes down for any reason. Both WAN ports (primary and secondary) must be configured to connect to the respective ISP’s before enabling this feature. The secondary WAN port will remain unconnected until a failure is detected on the primary link (either port can be assigned as the primary). In the event of a failure on the primary port, all internet traffic will be rolled over to the backup port. When configured in Auto Failover mode, the link status of the primary WAN port is checked at regular intervals as defined by the failure detection settings.
Unified Services Router User Manual 35 3.4.2 Load Balancing This feature allows you to use multiple WAN links (and presumably multiple ISP’s) simultaneously. After configuring more than one WAN port, the load balancing option is available to carry traffic over more than one link. Protocol bindings are used to segregate and assign services over one WAN port in order to manage internet flow. The configured failure detection method is used at regular intervals on all configured WAN ports when in Load Balancing mode. Load balancing is particularly useful when the connection speed of one WAN port greatly differs from another. In this case you can define protocol bindings to route low-latency services (such as VOIP) over the higher-speed link and let low-volume background traffic (such as SMPT) go over the lower speed link.
Unified Services Router User Manual 36 Figure 19: Load Balancing is available when multiple WAN ports are configured and Protocol Bindings have been defined 3.4.3 Protocol Bindings Advanced > Routing > Protocol Bindings Protocol bindings are required when the Load Balancing feature is in use. Choosing from a list of configured services or any of the user-defined services, the type of traffic can be assigned to go over only one of the available WAN ports. For increased flexibility the source network or machines can be specified as well as the destination network or machines. For example the VOIP traffic for a set of LAN IP addresses can be assigned to one WAN and any VIOP traffic from the remaining IP addresses can be assigned to the other WAN link. Protocol bindings are only applicable when load balancing mode is enabled and more than one WAN is configured.
Unified Services Router User Manual 37 Figure 20: Protocol binding setup to associate a service and/or LAN source to a WAN and/or destination network 3.5 Routing Configuration Routing between the LAN and WAN will impact the way this router handles traffic that is received on any of its physical interfaces. The routing mode of the gateway is core to the behavior of the traffic flow between the secure LAN and the internet. 3.5.1 Routing Mode Setup > Internet Settings > Routing Mode This device supports classical routing, network address translation (NAT), and transport mode routing. • With classical routing, devices on the LAN can be directly accessed from the internet by their public IP addresses (assuming appropriate firewall settings). If your ISP has assigned an IP address for each of the computers that you use, select Classic Routing. • NAT is a technique which allows several computers on a LAN to share an Internet connection. The computers on the LAN use a "private" IP address range while the WAN port on the router is configured with a single "public"
Unified Services Router User Manual 38 IP address. Along with connection sharing, NAT also hides internal IP addresses from the computers on the Internet. NAT is required if your ISP has assigned only one IP address to you. The computers that connect through the router will need to be assigned IP addresses from a private subnet. • Transparent mode routing between the LAN and WAN does not perform NAT. Broadcast and multicast packets that arrive on the LAN interface are switched to the WAN and vice versa, if they do not get filtered by firewall or VPN policies. If the LAN and WAN are in the same broadcast domain, select Transparent mode.
Unified Services Router User Manual 39 Figure 21: Routing Mode is used to configure traffic routing between WAN and LAN, as well as Dynamic routing (RIP) 3.5.2 Dynamic Routing (RIP) Setup > Internet Settings > Routing Mode
Unified Services Router User Manual 40 Dynamic routing using the Routing Information Protocol (RIP) is an Interior Gateway Protocol (IGP) that is common in LANs. With RIP this router can exchange routing information with other supported routers in the LAN and allow for dynamic adjustment of routing tables in order to adapt to modifications in the LAN without interrupting traffic flow. The RIP direction will define how this router sends and receives RIP packets. Choose between: • Both: The router both broadcasts its routing table and also processes RIP information received from other routers. This is the recommended setting in order to fully utilize RIP capabilities. • Out Only: The router broadcasts its routing table periodically but does not accept RIP information from other routers. • In Only: The router accepts RIP information from other routers, but does not broadcast its routing table. • None: The router neither broadcasts its route table nor does it accept any RIP packets from other routers. This effectively disables RIP. The RIP version is dependent on the RIP support of other routing devices in the LAN. • Disabled: This is the setting when RIP is disabled. • RIP-1 is a class-based routing version that does not include subnet information. This is the most commonly supported version. • RIP-2 includes all the functionality of RIPv1 plus it supports subnet information. Though the data is sent in RIP-2 format for both RIP-2B and RIP-2M, the mode in which packets are sent is different. RIP-2B broadcasts data in the entire subnet while RIP-2M sends data to multicast addresses. If RIP-2B or RIP-2M is the selected version, authentication between this router and other routers (configured with the same RIP version) is required. MD5 authentication is used in a first/second key exchange process. The authentication key validity lifetimes are configurable to ensure that the routing information exchange is with current and supported routers detected on the LAN. 3.5.3 Static Routing Advanced > Routing > Static Routing Advanced > IPv6 > IPv6 Static Routing Manually adding static routes to this device allows you to define the path selection of traffic from one interface to another. There is no communication between this router and other devices to account for changes in the path; once configured the static route will be active and effective until the network changes.
Unified Services Router User Manual 41 The List of Static Routes displays all routes that have been added manually by an administrator and allows several operations on the static routes. The List of IPv4 Static Routes and List of IPv6 Static Routes share the same fields (with one exception): • Name: Name of the route, for identification and management. • Active: Determines whether the route is active or inactive. A route can be added to the table and made inactive, if not needed. This allows routes to be used as needed without deleting and re-adding the entry. An inactive route is not broadcast if RIP is enabled. • Private: Determines whether the route can be shared with other routers when RIP is enabled. If the route is made private, then the route will not be shared in a RIP broadcast or multicast. This is only applicable for IPv4 static routes. • Destination: the route will lead to this destination host or IP address. • IP Subnet Mask: This is valid for IPv4 networks only, and identifies the subnet that is affected by this static route • Interface: The physical network interface (WAN1, WAN2, DMZ or LAN), through which this route is accessible. • Gateway: IP address of the gateway through which the destination host or network can be reached. • Metric: Determines the priority of the route. If multiple routes to the same destination exist, the route with the lowest metric is chosen.
Unified Services Router User Manual 42 Figure 22: Static route configuration fields 3.6 Configurable Port - WAN Option This router supports one of the physical ports to be configured as a secondary WAN Ethernet port or a dedicated DMZ port. If the port is selected to be a secondary WAN interface, all configuration pages relating to WAN2 are enabled. Setup > Internet Settings > WAN2 Setup WAN2 configuration is identical to the WAN1 configuration with one significant exception: configuration for the 3G USB modem is available only on WAN2.
Unified Services Router User Manual 43 Figure 23: WAN2 configuration for 3G internet (part 1) Cellular 3G internet access is available on WAN2 via a USB modem. The cellular ISP that provides the 3G data plan will provide the authentication requirements to establish a connection. The dial Number and APN are specific to the cellular carriers. Once the connection type settings are configured and saved, navigate to the WAN status page (Setup > Internet Settings > WAN Status) and Enable the WAN2 link to establish the 3G connection.
Unified Services Router User Manual 44 Figure 24: WAN2 configuration for 3G internet (part 2) 3.7 WAN Port Settings Advanced > Advanced Network > WAN Port Setup The physical port settings for each WAN link can be defined here. If your ISP account defines the WAN port speed or is associated with a MAC address, this information is required by the router to ensure a smooth connection with the network. The default MTU size supported by all ports is 1500. This is the largest packet size that can pass through the interface without fragmentation. This size can be increased, however large packets can introduce network lag and bring down the interface speed. Note that a 1500 byte size packet is the largest allowed by the Ethernet protocol at the network layer. The port speed can be sensed by the router when Auto is selected. With this option the optimal port settings are determined by the router and network. The duplex (half or full) can be defined based on the port support, as well as one of three port speeds: 10 Mbps, 100 Mbps and 1000 Mbps (i.e. 1 Gbps). The default setting is 100 Mbps for all ports.
Unified Services Router User Manual 45 The default MAC address is defined during the manufacturing process for the interfaces, and can uniquely identify this router. You can customize each WAN port’s MAC address as needed, either by letting the WAN port assume the current LAN host’s MAC address or by entering a MAC address manually. Figure 25: Physical WAN port settings
Unified Services Router User Manual 46 Chapter 4. Wireless Access Point Setup This router has an integrated 802.11n radio that allows you to create an access point for wireless LAN clients. The security/encryption/authentication options are grouped in a wireless Profile, and each configured profile will be available for selection in the AP configuration menu. The profile defines various parameters for the AP, including the security between the wireless client and the AP, and can be shared between multiple APs instances on the same device when needed. Up to four unique wireless networks can be created by configuring multiple “virtual” APs. Each such virtual AP appears as an independent AP (unique SSID) to supported clients in the environment, but is actually running on the same physical radio integrated with this router. You will need the following information to configure your wireless network: • Types of devices expected to access the wireless network and their supported Wi-Fi™ modes • The router’s geographical region • The security settings to use for securing the wireless network.  Profiles may be thought of as a grouping of AP parameters that can then be applied to not just one but multiple AP instances (SSIDs), thus avoiding duplication if the same parameters are to be used on multiple AP instances or SSIDs. 4.1 Wireless Settings Wizard Setup > Wizard > Wireless Settings The Wireless Network Setup Wizard is available for users new to networking. By going through a few straightforward configuration pages you can enable a Wi-Fi™ network on your LAN and allow supported 802.11 clients to connect to the configured Access Point.
Unified Services Router User Manual 47 Figure 26: Wireless Network Setup Wizards 4.1.1 Wireless Network Setup Wizard This wizard provides a step-by-step guide to create and secure a new access point on the router. The network name (SSID) is the AP identifier that will be detected by supported clients. The Wizard uses a TKIP+AES cipher for WPA / WPA2 security; depending on support on the client side, devices associate with this AP using either WPA or WPA2 security with the same pre-shared key. The wizard has the option to automatically generate a network key for the AP. This key is the pre-shared key for WPA or WPA2 type security. Supported clients that have been given this PSK can associate with this AP. The default (auto-assigned) PSK is “passphrase”. The last step in the Wizard is to click the Connect button, which confirms the settings and enables this AP to broadcast its availability in the LAN. 4.1.2 Add Wireless Device with WPS With WPS enabled on your router, the selected access point allows supported WPS clients to join the network very easily. When the Auto option for connecting a wireless device is chose, you will be presented with two common WPS setup options:
Unified Services Router User Manual 48 • Personal Identification Number (PIN): The wireless device that supports WPS may have an alphanumeric PIN, and if entered in this field the AP will establish a link to the client. Click Connect to complete setup and connect to the client. • Push Button Configuration (PBC): for wireless devices that support PBC, press and hold down on this button and within 2 minutes, click the PBC connect button. The AP will detect the wireless device and establish a link to the client.  You need to enable at least one AP with WPA/WPA2 security and also enable WPS in the Advanced > Wireless Settings > WPS page to use the WPS wizard. 4.1.3 Manual Wireless Network Setup This button on the Wizard page will link to the Setup> Wireless Settings> Access Points page. The manual options allow you to create new APs or modify the parameters of APs created by the Wizard. 4.2 Wireless Profiles Setup > Wireless Settings > Profiles The profile allows you to assign the security type, encryption and authentication to use when connecting the AP to a wireless client. The default mode is “open”, i.e. no security. This mode is insecure as it allows any compatible wireless clients to connect to an AP configured with this security profile. To create a new profile, use a unique profile name to identify the combination of settings. Configure a unique SSID that will be the identifier used by the clients to communicate to the AP using this profile. By choosing to broadcast the SSID, compatible wireless clients within range of the AP can detect this profile’s availability. The AP offers all advanced 802.11 security modes, including WEP, WPA, WPA2 and WPA+WPA2 options. The security of the Access point is configured by the Wireless Security Type section: • Open: select this option to create a public “open” network to allow unauthenticated devices to access this wireless gateway. • WEP (Wired Equivalent Privacy): this option requires a static (pre-shared) key to be shared between the AP and wireless client. Note that WEP does not support 802.11n data rates; is it appropriate for legacy 802.11 connections. • WPA (Wi-Fi Protected Access): For stronger wireless security than WEP, choose this option. The encryption for WPA will use TKIP and also CCMP if required. The authentication can be a pre-shared key (PSK), Enterprise mode with RADIUS
Unified Services Router User Manual 49 server, or both. Note that WPA does not support 802.11n data rates; is it appropriate for legacy 802.11 connections. • WPA2: this security type uses CCMP encryption (and the option to add TKIP encryption) on either PSK (pre-shared key) or Enterprise (RADIUS Server) authentication. • WPA + WPA2: this uses both encryption algorithms, TKIP and CCMP. WPA clients will use TKIP and WPA2 clients will use CCMP encryption algorithms.  “WPA+WPA2” is a security option that allows devices to connect to an AP using the strongest security that it supports. This mode allows legacy devices that only support WPA2 keys (such as an older wireless printer) to connect to a secure AP where all the other wireless clients are using WPA2. Figure 27: List of Available Profiles shows the variety of options available to secure the wireless link 4.2.1 WEP Security If WEP is the chosen security option, you must set a unique static key to be shared with clients that wish to access this secured wireless network. This static key can be generated from an easy-to-remember passphrase and the selected encryption length. • Authentication: select between Open System, or Shared Key schemes • Encryption: select the encryption key size -- 64 bit WEP or 128 bit WEP. The larger size keys provide stronger encryption, thus making the key more difficult to crack • WEP Passphrase: enter a alphanumeric phrase and click Generate Key to generate 4 unique WEP keys with length determined by the encryption key
Unified Services Router User Manual 50 size. Next choose one of the keys to be used for authentication. The selected key must be shared with wireless clients to connect to this device. Figure 28: Profile configuration to set network security 4.2.2 WPA or WPA2 with PSK A pre-shared key (PSK) is a known passphrase configured on the AP and client both and is used to authenticate the wireless client. An acceptable passphrase is between 8 to 63 characters in length.
Unified Services Router User Manual 51 4.2.3 RADIUS Authentication Setup > Wireless Settings > RADIUS Settings Enterprise Mode uses a RADIUS Server for WPA and/or WPA2 security. A RADIUS server must be configured and accessible by the router to authenticate wireless client connections to an AP enabled with a profile that uses RADIUS authentication. • The Authentication IP Address is required to identify the server. A secondary RADIUS server provides redundancy in the event that the primary server cannot be reached by the router when needed. • Authentication Port: the port for the RADIUS server connection • Secret: enter the shared secret that allows this router to log into the specified RADIUS server(s). This key must match the shared secret on the RADIUS Server. • The Timeout and Retries fields are used to either move to a secondary server if the primary cannot be reached, or to give up the RADIUS authentication attempt if communication with the server is not possible.
Unified Services Router User Manual 52 Figure 29: RADIUS server (External Authentication) configuration 4.3 Creating and Using Access Points Setup > Wireless Settings > Access Points Once a profile (a group of security settings) is created, it can be assigned to an AP on the router. The AP SSID can be configured to broadcast its availability to the 802.11 environment can be used to establish a WLAN network. The AP configuration page allows you to create a new AP and link to it one of the available profiles. This router supports multiple AP’s referred to as virtual access points (VAPs). Each virtual AP that has a unique SSIDs appears as an independent access point to clients. This valuable feature allows the router’s radio to be configured in a way to optimize security and throughput for a group of clients as required by the user. To create a VAP, click the “add” button on the Setup > Wireless Settings > Access Points page. After setting the AP name, the profile dropdown menu is used to select one of the configured profiles.  The AP Name is a unique identifier used to manage the AP from the GUI, and is not the SSID that is detected by clients when the AP has broadcast enabled.
Unified Services Router User Manual 53 Figure 30: Virtual AP configuration A valuable power saving feature is the start and stop time control for this AP. You can conserve on the radio power by disabling the AP when it is not in use. For example on evenings and weekends if you know there are no wireless clients, the start and stop time will enable/disable the access point automatically. Once the AP settings are configured, you must enable the AP on the radio on the Setup > Wireless Settings > Access Points page. The status field changes to “Enabled” if the AP is available to accept wireless clients. If the AP is configured to broadcast its SSID (a profile parameter), a green check mark indicating it is broadcasting will be shown in the List of Available Access points.
Unified Services Router User Manual 54 Figure 31: List of configured access points (Virtual APs) shows one enabled access point on the radio, broadcasting its SSID The clients connected to a particular AP can be viewed by using the Status Button on the List of Available Access Points. Traffic statistics are shown for that individual AP, as compared to the summary stats for each AP on the Statistics table. Connected clients are sorted by the MAC address and indicate the security parameters used by the wireless link, as well as the time connected to this particular AP. Clicking the Details button next to the connected client will give the detailed send and receive traffic statistics for the wireless link between this AP and the client. 4.3.1 Primary benefits of Virtual APs: • Optimize throughput: if 802.11b, 802.11 g, and 802.11n clients are expected to access the LAN via this router, creating 3 VAPs will allow you to manage or shape traffic for each group of clients. A unique SSID can be created for the network of 802.11b clients and another SSID can be assigned for the 802.11n clients. Each can have different security parameters – remember, the SSID and security of the link is determined by the profile. In this way legacy clients can access the network without bringing down the overall throughput of more capable 802.11n clients. • Optimize security: you may wish to support select legacy clients that only offer WEP security while using WPA2 security for the majority of clients for the radio. By creating two VAPs configured with different SSIDs and different security parameters, both types of clients can connect to the LAN. Since WPA2 is more secure, you may want to broadcast this SSID and not broadcast the SSID for the VAP with WEP since it is meant to be used for a few legacy devices in this scenario.
Unified Services Router User Manual 55 4.4 Tuning Radio Specific Settings Setup > Wireless Settings > Radio Settings The Radio Settings page lets you configure the channels and power levels available for the AP’s enabled on the device. The router has a dual band 802.11n radio, meaning either 2.4 GHz or 5 GHz frequency of operation can be selected (not concurrently though). Based on the selected operating frequency, the mode selection will let you define whether legacy connections or only 802.11n connections (or both) are accepted on configured APs. Figure 32: Radio card configuration options The ratified 802.11n support on this radio requires selecting the appropriate broadcast (NA or NG etc.) mode, and then defining the channel spacing and control side band for 802.11n traffic. The default settings are appropriate for most networks. For example, changing the channel spacing to 40 MHz can improve bandwidth at the expense of supporting earlier 802.11n clients. The available transmission channels are governed by regulatory constraints based on the region setting of the router. The maximum transmission power is similarly governed by regulatory limits; you have the option to decrease from the default maximum to reduce the signal strength of traffic out of the radio.
Unified Services Router User Manual 56 4.5 Advanced Wireless Settings Advanced > Wireless Settings > Advanced Wireless Sophisticated wireless administrators can modify the 802.11 communication parameters in this page. Generally, the default settings are appropriate for most networks. Please refer to the GUI integrated help text for further details on the use of each configuration parameter. Figure 33: Advanced Wireless communication settings 4.6 Wi-Fi Protected Setup (WPS) Advanced > Wireless Settings > WPS WPS is a simplified method to add supporting wireless clients to the network. WPS is only applicable for APs that employ WPA or WPA2 security. To use WPS, select the eligible VAPs from the dropdown list of APs that have been configured with this security and enable WPS status for this AP. The WPS Current Status section outlines the security, authentication, and encryption settings of the selected AP. These are consistent with the AP’s profile. There are two setup options available for WPS: • Personal Identification Number (PIN): The wireless device that supports WPS may have an alphanumeric PIN, if so add the PIN in this field. The router will
Unified Services Router User Manual 57 connect within 60 seconds of clicking the “Configure via PIN” button immediately below the PIN field. There is no LED indication that a client has connected. • Push Button Configuration (PBC): for wireless devices that support PBC, press and hold down on this button and within 2 minutes click the PBC connect button. The AP will detect the wireless device and establish a link to the client.  More than one AP can use WPS, but only one AP can be used to establish WPS links to client at any given time. Figure 34: WPS configuration for an AP with WPA/WPA2 profile
Chapter 5. Securing the Private Network You can secure your network by creating and applying rules that your router uses to selectively block and allow inbound and outbound Internet traffic. You then specify how and to whom the rules apply. To do so, you must define the following: • Services or traffic types (examples: web browsing, VoIP, other standard services and also custom services that you define) • Direction for the traffic by specifying the source and destination of traffic; this is done by specifying the “From Zone” (LAN/WAN/DMZ) and “To Zone” (LAN/WAN/DMZ) • Schedules as to when the router should apply rules • Any Keywords (in a domain name or on a URL of a web page) that the router should allow or block • Rules for allowing or blocking inbound and outbound Internet traffic for specified services on specified schedules • MAC addresses of devices that should not access the internet • Port triggers that signal the router to allow or block access to specified services as defined by port number • Reports and alerts that you want the router to send to you You can, for example, establish restricted-access policies based on time-of-day, web addresses, and web address keywords. You can block Internet access by applications and services on the LAN, such as chat rooms or games. You can block just certain groups of PCs on your network from being accessed by the WAN or public DMZ network. 5.1 Firewall Rules Advanced > Firewall Settings > Firewall Rules Inbound (WAN to LAN/DMZ) rules restrict access to traffic entering your network, selectively allowing only specific outside users to access specific local resources. By default all access from the insecure WAN side are blocked from accessing the secure LAN, except in response to requests from the LAN or DMZ. To allow outside devices to access services on the secure LAN, you must create an inbound firewall rule for each service. If you want to allow incoming traffic, you must make the router’s WAN port IP address known to the public. This is called “exposing your host.” How you make your address known depends on how the WAN ports are configured; for this router you
Unified Services Router User Manual 60 may use the IP address if a static address is assigned to the WAN port, or if your WAN address is dynamic a DDNS (Dynamic DNS) name can be used. Outbound (LAN/DMZ to WAN) rules restrict access to traffic leaving your network, selectively allowing only specific local users to access specific outside resources. The default outbound rule is to allow access from the secure zone (LAN) to either the public DMZ or insecure WAN. You can change this default behavior in the Firewall Settings > Default Outbound Policy page. When the default outbound policy is allow always, you can to block hosts on the LAN from accessing internet services by creating an outbound firewall rule for each service. Figure 35: List of Available Firewall Rules 5.2 Defining Rule Schedules Tools > Schedules Firewall rules can be enabled or disabled automatically if they are associated with a configured schedule. The schedule configuration page allows you to define days of the week and the time of day for a new schedule, and then this schedule can be selected in the firewall rule configuration page.  All schedules will follow the time in the routers configured time zone. Refer to the section on choosing your Time Zone and configuring NTP servers for more information.
Unified Services Router User Manual 61 Figure 36: List of Available Schedules to bind to a firewall rule 5.3 Configuring Firewall Rules Advanced > Firewall Settings > Firewall Rules All configured firewall rules on the router are displayed in the Firewall Rules list. This list also indicates whether the rule is enabled (active) or not, and gives a summary of the From/To zone as well as the services or users that the rule affects. To create a new firewall rules, follow the steps below: 1. View the existing rules in the List of Available Firewall Rules table. 2. To edit or add an outbound or inbound services rule, do the following: • To edit a rule, click the checkbox next to the rule and click Edit to reach that rule’s configuration page. • To add a new rule, click Add to be taken to a new rule’s configuration page. Once created, the new rule is automatically added to the original table. 3. Chose the From Zone to be the source of originating traffic: either the secure LAN, public DMZ, or insecure WAN. For an inbound rule WAN should be selected as the From Zone. 4. Choose the To Zone to be the destination of traffic covered by this rule. If the From Zone is the WAN, the To Zone can be the public DMZ or secure LAN. Similarly if the From Zone is the LAN, then the To Zone can be the public DMZ or insecure WAN. 5. Parameters that define the firewall rule include the following:
Unified Services Router User Manual 62 • Service: ANY means all traffic is affected by this rule. For a specific service the drop down list has common services, or you can select a custom defined service. • Action & Schedule: Select one of the 4 actions that this rule defines: BLOCK always, ALLOW always, BLOCK by schedule otherwise ALLOW, or ALLOW by schedule otherwise BLOCK. A schedule must be preconfigured in order for it to be available in the dropdown list to assign to this rule. • Source & Destination users: For each relevant category, select the users to which the rule applies: • Any (all users) • Single Address (enter an IP address) • Address Range (enter the appropriate IP address range) • Log: traffic that is filtered by this rule can be logged; this requires configuring the router’s logging feature separately. • QoS Priority: Outbound rules (where To Zone = insecure WAN only) can have the traffic marked with a QoS priority tag. Select a priority level: • Normal-Service: ToS=0 (lowest QoS) • Minimize-Cost: ToS=1 • Maximize-Reliability: ToS=2 • Maximize-Throughput: ToS=4 • Minimize-Delay: ToS=8 (highest QoS) 6. Inbound rules can use Destination NAT (DNAT) for managing traffic from the WAN. Destination NAT is available when the To Zone = DMZ or secure LAN. • With an inbound allow rule you can enter the internal server address that is hosting the selected service. • You can enable port forwarding for an incoming service specific rule (From Zone = WAN) by selecting the appropriate checkbox. This will allow the selected service traffic from the internet to reach the appropriate LAN port via a port forwarding rule. • Translate Port Number: With port forwarding, the incoming traffic to be forwarded to the port number entered here.
Unified Services Router User Manual 63 • External IP address: The rule can be bound to a specific WAN interface by selecting either the primary WAN or configurable port WAN as the source IP address for incoming traffic.  This router supports multi-NAT and so the External IP address does not necessarily have to be the WAN address. On a single WAN interface, multiple public IP addresses are supported. If your ISP assigns you more than one public IP address, one of these can be used as your primary IP address on the WAN port, and the others can be assigned to servers on the LAN or DMZ. In this way the LAN/DMZ server can be accessed from the internet by its aliased public IP address. 7. Outbound rules can use Source NAT (SNAT) in order to statically map (bind) all LAN/DMZ traffic matching the rule parameters to a specific WAN interface or external IP address (usually provided by your ISP). Once the new or modified rule parameters are saved, it appears in the master list of firewall rules. To enable or disable a rule, click the checkbox next to the rule in the list of firewall rules and choose Enable or Disable.  The router applies firewall rules in the order listed. As a general rule, you should move the strictest rules (those with the most specific services or addresses) to the top of the list. To reorder rules, click the checkbox next to a rule and click up or down.
Unified Services Router User Manual 64 Figure 37: The firewall rule configuration page allows you to define the To/From zone, service, action, schedules, and specify source/destination IP addresses as needed.
Unified Services Router User Manual 65 5.3.1 Firewall Rule Configuration Examples Example 1: Allow inbound HTTP traffic to the DMZ Situation: You host a public web server on your local DMZ network. You want to allow inbound HTTP requests from any outside IP address to the IP address of your web server at any time of day. Solution: Create an inbound rule as follows. Parameter Value From Zone Insecure (WAN1/WAN2) To Zone Public (DMZ) Service HTTP Action ALLOW always Send to Local Server (DNAT IP) 192.168.5.2 (web server IP address) Destination Users Any Log Never Example 2: Allow videoconferencing from range of outside IP addresses Situation: You want to allow incoming videoconferencing to be initiated from a restricted range of outside IP addresses (132.177.88.2 - 132.177.88.254), from a branch office. Solution: Create an inbound rule as follows. In the example, CUSeeMe (the video conference service used) connections are allowed only from a specified range of external IP addresses. Parameter Value From Zone Insecure (WAN1/WAN2) To Zone Secure (LAN) Service CU-SEEME:UDP Action ALLOW always Send to Local Server (DNAT IP) 192.168.10.11 Destination Users Address Range From 132.177.88.2 To 134.177.88.254 Enable Port Forwarding Yes (enabled) Example 3: Multi-NAT configuration Situation: You want to configure multi-NAT to support multiple public IP addresses on one WAN port interface. Solution: Create an inbound rule that configures the firewall to host an additional public IP address. Associate this address with a web server on the DMZ. If you
Unified Services Router User Manual 66 arrange with your ISP to have more than one public IP address for your use, you can use the additional public IP addresses to map to servers on your LAN. One of these public IP addresses is used as the primary IP address of the router. This address is used to provide Internet access to your LAN PCs through NAT. The other addresses are available to map to your DMZ servers. The following addressing scheme is used to illustrate this procedure: Router • WAN IP address: 10.1.0.118 • LAN IP address: 192.168.10.1; subnet 255.255.255.0 • Web server host in the DMZ, IP address: 192.168.12.222 • Access to Web server: (simulated) public IP address 10.1.0.52 Example 4: Block traffic by schedule if generated from specific range of machines Use Case: Block all HTTP traffic on the weekends if the request originates from a specific group of machines in the LAN having a known range of IP addresses, and anyone coming in through the Network from the WAN (i.e. all remote users). Configuration: 1. Setup a schedule: • To setup a schedule that affects traffic on weekends only, navigate to Security: Schedule, and name the schedule “Weekend” • Define “weekend” to mean 12 am Saturday morning to 12 am Monday morning – all day Saturday & Sunday • In the Scheduled days box, check that you want the schedule to be active for “specific days”. Select “Saturday” and “Sunday” • In the scheduled time of day, select “all day” – this will apply the schedule between 12 am to 11:59 pm of the selected day. Parameter Value From Zone Insecure (WAN1/WAN2) To Zone Public (DMZ) Service HTTP Action ALLOW always Send to Local Server (DNAT IP) 192.168.12.222 ( web server local IP address) Destination Users Single Address From 10.1.0.52 WAN Users Any Log Never
Unified Services Router User Manual 67 • Click apply – now schedule “Weekend” isolates all day Saturday and Sunday from the rest of the week. Figure 38: Schedule configuration for the above example. 2. Since we are trying to block HTTP requests, it is a service with To Zone: Insecure (WAN1/WAN2) that is to be blocked according to schedule “Weekend”.
Unified Services Router User Manual 68 3. Select the Action to “Block by Schedule, otherwise allow”. This will take a predefined schedule and make sure the rule is a blocking rule during the defined dates/times. All other times outside the schedule will not be affected by this firewall blocking rule 4. As we defined our schedule in schedule “Weekend”, this is available in the dropdown menu 5. We want to block the IP range assigned to the marketing group. Let’s say they have IP 192.168.10.20 to 192.168.10.30. On the Source Users dropdown, select Address Range and add this IP range as the From and To IP addresses. 6. We want to block all HTTP traffic to any services going to the insecure zone. The Destination Users dropdown should be “any”. 7. We don’t need to change default QoS priority or Logging (unless desired) – clicking apply will add this firewall rule to the list of firewall rules. 8. The last step is to enable this firewall rule. Select the rule, and click “enable” below the list to make sure the firewall rule is active 5.4 Security on Custom Services Advanced > Firewall Settings > Custom Services Custom services can be defined to add to the list of services available during firewall rule configuration. While common services have known TCP/UDP/ICMP ports for traffic, many custom or uncommon applications exist in the LAN or WAN. In the custom service configuration menu you can define a range of ports and identify the traffic type (TCP/UDP/ICMP) for this service. Once defined, the new service will appear in the services list of the firewall rules configuration menu.
Unified Services Router User Manual 69 Figure 39: List of user defined services. 5.5 ALG support Advanced > Firewall Settings > ALGs Application Level Gateways (ALGs) are security component that enhance the firewall and NAT support of this router to seamlessly support application layer protocols. In some cases enabling the ALG will allow the firewall to use dynamic ephemeral TCP/ UDP ports to communicate with the known ports a particular client application (such as H.323 or RTSP) requires, without which the admin would have to open large number of ports to accomplish the same support. Because the ALG understands the protocol used by the specific application that it supports, it is a very secure and efficient way of introducing support for client applications through the router’s firewall.
Unified Services Router User Manual 70 Figure 40: Available ALG support on the router. 5.6 VPN Passthrough for Firewall Advanced > Firewall Settings > VPN Passthrough This router’s firewall settings can be configured to allow encrypted VPN traffic for IPSec, PPTP, and L2TP VPN tunnel connections between the LAN and internet. A specific firewall rule or service is not appropriate to introduce this passthrough support; instead the appropriate check boxes in the VPN Passthrough page must be enabled.
Unified Services Router User Manual 71 Figure 41: Passthrough options for VPN tunnels 5.7 Application Rules Advanced > Application Rules > Application Rules Application rules are also referred to as port triggering. This feature allows devices on the LAN or DMZ to request one or more ports to be forwarded to them. Port triggering waits for an outbound request from the LAN/DMZ on one of the defined outgoing ports, and then opens an incoming port for that specified type of traffic. This can be thought of as a form of dynamic port forwarding while an application is transmitting data over the opened outgoing or incoming port(s). Port triggering application rules are more flexible than static port forwarding that is an available option when configuring firewall rules. This is because a port triggering rule does not have to reference a specific LAN IP or IP range. As well ports are not left open when not in use, thereby providing a level of security that port forwarding does not offer.  Port triggering is not appropriate for servers on the LAN, since there is a dependency on the LAN device making an outgoing connection before incoming ports are opened. Some applications require that when external devices connect to them, they receive data on a specific port or range of ports in order to function properly. The router must send all incoming data for that application only on the required port or range of ports. The router has a list of common applications and games with corresponding outbound and inbound ports to open. You can also specify a port triggering rule by defining the type of traffic (TCP or UDP) and the range of incoming and outgoing ports to open when enabled.
Unified Services Router User Manual 72 Figure 42: List of Available Application Rules showing 4 unique rules The application rule status page will list any active rules, i.e. incoming ports that are being triggered based on outbound requests from a defined outgoing port. 5.8 Web Content Filtering The gateway offers some standard web filtering options to allow the admin to easily create internet access policies between the secure LAN and insecure WAN. Instead of creating policies based on the type of traffic (as is the case when using firewall rules), web based content itself can be used to determine if traffic is allowed or dropped. • Content Filtering Advanced > Website Filter > Content Filtering Content filtering must be enabled to configure and use the subsequent features (list of Trusted Domains, filtering on Blocked Keywords, etc.). Proxy servers, which can be used to circumvent certain firewall rules and thus a potential security gap, can be blocked for all LAN devices. Java applets can be prevented from being downloaded from internet sites, and similarly the gateway can prevent ActiveX controls from being downloaded via Internet Explorer. For added security cookies, which typically contain session information, can be blocked as well for all devices on the private network.
Unified Services Router User Manual 73 Figure 43: Content Filtering used to block access to proxy servers and prevent ActiveX controls from being downloaded • Approved URLs Advanced > Website Filter > Approved URLs The Approved URLs is an acceptance list for all URL domain names. Domains added to this list are allowed in any form. For example, if the domain “yahoo” is added to this list then all of the following URL’s are permitted access from the LAN: www.yahoo.com, yahoo.co.uk, etc.
Unified Services Router User Manual 74 Figure 44: Two trusted domains added to the Approved URLs List • Blocked Keywords Advanced > Website Filter > Blocked Keywords Keyword blocking allows you to block all website URL’s or site content that contains the keywords in the configured list. This is lower priority than the Approved URL List; i.e. if the blocked keyword is present in a site allowed by a Trusted Domain in the Approved URL List, then access to that site will be allowed.
Unified Services Router User Manual 75 Figure 45: Two keywords added to the block list 5.9 IP/MAC Binding Advanced > IP/MAC Binding Another available security measure is to only allow outbound traffic (from the LAN to WAN) when the LAN node has an IP address matching the MAC address bound to it. This is IP/MAC Binding, and by enforcing the gateway to validate the source traffic’s IP address with the unique MAC Address of the configured LAN node, the administrator can ensure traffic from that IP address is not spoofed. In the event of a violation (i.e. the traffic’s source IP address doesn’t match up with the expected MAC address having the same IP address) the packets will be dropped and can be logged for diagnosis.
Unified Services Router User Manual 76 Figure 46: The above example of IP/MAC Binding binds a LAN host’s MAC Address to an IP address. If there is an IP/MAC Binding violation, the violating packet will be dropped and logs will be captured 5.10 Intrusion Prevention (IPS) Advanced > Advanced Network > IPS The gateway’s Intrusion Prevention System (IPS) prevents malicious attacks from the internet from accessing the private network. Static attack signatures loaded to the device allow common attacks to be detected and prevented. The checks can be enabled between the WAN and DMZ or LAN, and a running counter will allow the administrator to see how many malicious intrusion attempts from the WAN have been detected and prevented.
Unified Services Router User Manual 77 Figure 47: Intrusion Prevention features on the router 5.10.1 Protecting from Internet Attacks Advanced > Advanced Network > Attack Checks Attacks can be malicious security breaches or unintentional network issues that render the router unusable. Attack checks allow you to manage WAN security threats such as continual ping requests and discovery via ARP scans. TCP and UDP flood attack checks can be enabled to manage extreme usage of WAN resources. Additionally certain Denial-of-Service (DoS) attacks can be blocked. These attacks, if uninhibited, can use up processing power and bandwidth and prevent regular network services from running normally. ICMP packet flooding, SYN traffic flooding, and Echo storm thresholds can be configured to temporarily suspect traffic from the offending source.
Unified Services Router User Manual 78 Figure 48: Protecting the router and LAN from internet attacks
Unified Services Router User Manual 79 Chapter 6. IPSec / PPTP / L2TP VPN A VPN provides a secure communication channel (“tunnel”) between two gateway routers or a remote PC client. The following types of tunnels can be created: • Gateway-to-gateway VPN: to connect two or more routers to secure traffic between remote sites. • Remote Client (client-to-gateway VPN tunnel): A remote client initiates a VPN tunnel as the IP address of the remote PC client is not known in advance. The gateway in this case acts as a responder. • Remote client behind a NAT router: The client has a dynamic IP address and is behind a NAT Router. The remote PC client at the NAT router initiates a VPN tunnel as the IP address of the remote NAT router is not known in advance. The gateway WAN port acts as responder. • PPTP server for LAN / WAN PPTP client connections. • L2TP server for LAN / WAN L2TP client connections. 6.1 VPN Wizard Setup > Wizard > VPN Wizard You can use the VPN wizard to quickly create both IKE and VPN policies. Once the IKE or VPN policy is created, you can modify it as required.
Unified Services Router User Manual 80 Figure 49: VPN Wizard launch screen To easily establish a VPN tunnel using VPN Wizard, follow the steps below: 1. Step 1: Select the VPN tunnel type to create • The tunnel can either be a gateway to gateway connection (site-to-site) or a tunnel to a host on the internet (remote access). • Set the Connection Name and pre-shared key: the connection name is used for management, and the pre-shared key will be required on the VPN client or gateway to establish the tunnel • Determine the local gateway for this tunnel; if there is more than 1 WAN configured the tunnel can be configured for either of the gateways. 2. Step 2: Configure Remote and Local WAN address for the tunnel endpoints • Remote Gateway Type: identify the remote endpoint of the tunnel by FQDN or static IP address • Remote WAN IP address / FQDN: This field is enabled only if the peer you are trying to connect to is a Gateway. For VPN Clients, this IP address or Internet Name is determined when a connection request is received from a client. • Local Gateway Type: identify this router’s endpoint of the tunnel by FQDN or static IP address
Unified Services Router User Manual 81 • Local WAN IP address / FQDN: This field can be left blank if you are not using a different FQDN or IP address than the one specified in the WAN port’s configuration. 3. Step 3: Configure the Secure Connection Remote Accessibility fields to identify the remote network: • Remote LAN IP address: address of the LAN behind the peer gateway • Remote LAN Subnet Mask: the subnet mask of the LAN behind the peer  Note: The IP address range used on the remote LAN must be different from the IP address range used on the local LAN. 4. Step4: review the settings and click Connect to establish the tunnel. The Wizard will create a Auto IPSec policy with the following default values for a VPN Client or Gateway policy (these can be accessed from a link on the Wizard page): Parameter Default value from Wizard Exchange Mode Aggressive (Client policy ) or Main (Gateway policy) ID Type FQDN Local WAN ID wan_local.com (only applies to Client policies) Remote WAN ID wan_remote.com (only applies to Client policies) Encryption Algorithm 3DES Authentication Algorithm SHA-1 Authentication Method Pre-shared Key PFS Key-Group DH-Group 2(1024 bit) Life Time (Phase 1) 24 hours Life Time (Phase 2) 8 hours NETBIOS Enabled (only applies to Gateway policies)  The VPN Wizard is the recommended method to set up an Auto IPSec policy. Once the Wizard creates the matching IKE and VPN policies required by the Auto policy, one can modify the required fields through the edit link. Refer to the online help for details.
Unified Services Router User Manual 82 6.2 Configuring IPSec Policies Setup > VPN Settings > IPSec > IPSec Policies A IPSec policy is between this router and another gateway or this router and a IPSec client on a remote host. The IPSec mode can be either tunnel or transport depending on the network being traversed between the two policy endpoints. • Transport: This is used for end-to-end communication between this router and the tunnel endpoint, either another IPSec gateway or an IPSec VPN client on a host. Only the data payload is encrypted and the IP header is not modified or encrypted. • Tunnel: This mode is used for network-to-network IPSec tunnels where this gateway is one endpoint of the tunnel. In this mode the entire IP packet including the header is encrypted and/or authenticated. When tunnel mode is selected, you can enable NetBIOS and DHCP over IPSec. DHCP over IPSec allows this router to serve IP leases to hosts on the remote LAN. As well in this mode you can define the single IP address, range of IPs, or subnet on both the local and remote private networks that can communicate over the tunnel.
Unified Services Router User Manual 83 Figure 50: IPSec policy configuration Once the tunnel type and endpoints of the tunnel are defined you can determine the Phase 1 / Phase 2 negotiation to use for the tunnel. This is covered in the IPSec mode setting, as the policy can be Manual or Auto. For Auto policies, the Internet Key Exchange (IKE) protocol dynamically exchanges keys between two IPSec hosts. The Phase 1 IKE parameters are used to define the tunnel’s security association details. The Phase 2 Auto policy parameters cover the security association lifetime and encryption/authentication details of the phase 2 key negotiation. The VPN policy is one half of the IKE/VPN policy pair required to establish a Auto IPSec VPN tunnel. The IP addresses of the machine or machines on the two VPN endpoints are configured here, along with the policy parameters required to secure the tunnel
Unified Services Router User Manual 84 Figure 51: IPSec policy configuration continued (Auto policy via IKE) A Manual policy does not use IKE and instead relies on manual keying to exchange authentication parameters between the two IPSec hosts. The incoming and outgoing security parameter index (SPI) values must be mirrored on the remote tunnel endpoint. As well the encryption and integrity algorithms and keys must match on the remote IPSec host exactly in order for the tunnel to establish successfully. Note that using Auto policies with IKE are preferred as in some IPSec implementations the SPI (security parameter index) values require conversion at each endpoint.
Unified Services Router User Manual 85 Figure 52: IPSec policy configuration continued (Auto / Manual Phase 2) 6.2.1 Extended Authentication (XAUTH) You can also configure extended authentication (XAUTH). Rather than configure a unique VPN policy for each user, you can configure the VPN gateway router to authenticate users from a stored list of user accounts or with an external authentication server such as a RADIUS server. With a user database, user accounts created in the router are used to authenticate users. With a configured RADIUS server, the router connects to a RADIUS server and passes to it the credentials that it receives from the VPN client. You can secure the connection between the router and the RADIUS server with the authentication protocol supported by the server (PAP or CHAP). For RADIUS – PAP, the router first checks in the user database to see if the user credentials are available; if they are not, the router connects to the RADIUS server. 6.3 Configuring VPN clients Remote VPN clients must be configured with the same VPN policy parameters used in the VPN tunnel that the client wishes to use: encryption, authentication, life time, and PFS key-group. Upon establishing these authentication parameters, the VPN Client user database must also be populated with an account to give a user access to the tunnel.
Unified Services Router User Manual 86  VPN client software is required to establish a VPN tunnel between the router and remote endpoint. Open source software (such as OpenVPN or Openswan) as well as Microsoft IPSec VPN software can be configured with the required IKE policy parameters to establish an IPSec VPN tunnel. Refer to the client software guide for detailed instructions on setup as well as the router’s online help. The user database contains the list of VPN user accounts that are authorized to use a given VPN tunnel. Alternatively VPN tunnel users can be authenticated using a configured Radius database. Refer to the online help to determine how to populate the user database and/or configure RADIUS authentication. 6.4 PPTP / L2TP Tunnels This router supports VPN tunnels from either PPTP or L2TP ISP servers. The router acts as a broker device to allow the ISP's server to create a TCP control connection between the LAN VPN client and the VPN server. 6.4.1 PPTP Tunnel Support Setup > VPN Settings > PPTP > PPTP Server A PPTP VPN can be established through this router. Once enabled a PPTP server is available on the router for LAN and WAN PPTP client users to access. Once the PPTP server is enabled, PPTP clients that are within the range of configured IP addresses of allowed clients can reach the router’s PPTP server. Once authenticated by the PPTP server (the tunnel endpoint), PPTP clients have access to the network managed by the router.
Unified Services Router User Manual 87 Figure 53: PPTP tunnel configuration – PPTP Server 6.4.2 L2TP Tunnel Support Setup > VPN Settings > L2TP > L2TP Server A L2TP VPN can be established through this router. Once enabled a L2TP server is available on the router for LAN and WAN L2TP client users to access. Once the L2TP server is enabled, L2TP clients that are within the range of configured IP addresses of allowed clients can reach the router’s L2TP server. Once authenticated by the L2TP server (the tunnel endpoint), L2TP clients have access to the network managed by the router. Figure 54: L2TP tunnel configuration – L2TP Server
Chapter 7. SSL VPN The router provides an intrinsic SSL VPN feature as an alternate to the standard IPSec VPN. SSL VPN differs from IPSec VPN mainly by removing the requirement of a pre-installed VPN client on the remote host. Instead, users can securely login through the SSL User Portal using a standard web browser and receive access to configured network resources within the corporate LAN. The router supports multiple concurrent sessions to allow remote users to access the LAN over an encrypted link through a customizable user portal interface, and each SSL VPN user can be assigned unique privileges and network resource access levels. The remote user can be provided different options for SSL service through this router: • VPN Tunnel: The remote user’s SSL enabled browser is used in place of a VPN client on the remote host to establish a secure VPN tunnel. A SSL VPN client (Active-X or Java based) is installed in the remote host to allow the client to join the corporate LAN with pre-configured access/policy privileges. At this point a virtual network interface is created on the user’s host and this will be assigned an IP address and DNS server address from the router. Once established, the host machine can access allocated network resources. • Port Forwarding: A web-based (ActiveX or Java) client is installed on the client machine again. Note that Port Forwarding service only supports TCP connections between the remote user and the router. The router administrator can define specific services or applications that are available to remote port forwarding users instead of access to the full LAN like the VPN tunnel.  ActiveX clients are used when the remote user accesses the portal using the Internet Explorer browser. The Java client is used for other browsers like Mozilla Firefox, Netscape Navigator, Google Chrome, and Apple Safari. 7.1 Users, Groups, and Domains Advanced > Users > Users Authentication of the users (IPSec, SSL VPN, or GUI) is done by the router using either a local database on the router or external authentication servers (i.e. LDAP or RADIUS). The remote user must specify the user, group and domain when logging in to the router. One or more users are members of a Group. One or more Groups belong to an authentication Domain.
Unified Services Router User Manual 90 Figure 55: Available Users with login status and associated Group/Domain Advanced > Users > Domains The Domain determines the authentication method (local user database, external server) to be used when validating the remote user’s connection. As well the Domain determines the portal layout presented to the remote SSL user. Since the portal layout assigns access to SSL VPN tunnel and/or SSL VPN Port Forwarding features, the domain is essential in defining the authentication and features exposed to SSL users. Advanced > Users > Groups Groups are used to assign access policies to a set of SSL users within a domain. Groups are domain subsets that can be seen as types of SSL users; some groups require access to all available network resources and some can be provided access to a select few. With groups, a very secure hierarchy of SSL VPN remote access can be created for all types of users with minimal number of policies to configure.  You must create a Domain first, and then a new Group can be created and assigned to the Domain. The last step is to add specific SSL VPN users to an already-configured Group. 7.1.1 User Types and Passwords Advanced > Users > Users User level policies can be specified by browser, IP address of the host, and whether the user can login to the router’s GUI in addition to the SSL VPN portal. The
Unified Services Router User Manual 91 following user types are assigned to a user that reaches the GUI login screen from the LAN or WAN: • Administrator: This is the router’s super-user, and can manage the router, use SSL VPN to access network resources, and login to L2TP/PPTP servers on the WAN. There will always be one default administrator user for the GUI. • Guest (read only): The guest user gains read only access to the GUI to observe and review configuration settings. The guest does not have SSL VPN access. • SSL VPN User: This user has access to the SSL VPN services as determined by the group policies and authentication domain of which it is a member. The domain-determined SSL VPN portal will be displayed when logging in with this user type. • XAuth User: This user’s authentication is performed by an externally configured RADIUS or other Enterprise server. It is not part of the local user database. • L2TP User: These are L2TP VPN tunnel LAN users that can establish a tunnel with the L2TP server on the WAN. • PPTP User: These are PPTP VPN tunnel LAN users that can establish a tunnel with the PPTP server on the WAN. • Local User: This user’s authentication domain is located on the router itself. Once the user type is determined, you can define/modify the password and idle login timeout for the user. It is recommended that passwords contains no dictionary words from any language, and is a mixture of letters (both uppercase and lowercase), numbers, and symbols. The password can be up to 30 characters.
Unified Services Router User Manual 92 Figure 56: User configuration options 7.2 Using SSL VPN Policies Setup > VPN Settings > SSL VPN Server > SSL VPN Policies SSL VPN Policies can be created on a Global, Group, or User level. User level policies take precedence over Group level policies and Group level policies take precedence over Global policies. These policies can be applied to a specific network resource, IP address or ranges on the LAN, or to different SSL VPN services supported by the router. The List of Available Policies can be filtered based on whether it applies to a user, group, or all users (global).  A more specific policy takes precedence over a generic policy when both are applied to the same user/group/global domain. I.e. a policy for a specific IP address takes precedence over a policy for a range of addresses containing the IP address already referenced.
Unified Services Router User Manual 93 Figure 57: List of SSL VPN polices (Global filter) To add a SSL VPN policy, you must first assign it to a user, group, or make it global (i.e. applicable to all SSL VPN users). If the policy is for a group, the available configured groups are shown in a drop down menu and one must be selected. Similarly, for a user defined policy a SSL VPN user must be chosen from the available list of configured users. The next step is to define the policy details. The policy name is a unique identifier for this rule. The policy can be assigned to a specific Network Resource (details follow in the subsequent section), IP address, IP network, or all devices on the LAN of the router. Based on the selection of one of these four options, the appropriate configuration fields are required (i.e. choosing the network resources from a list of defined resources, or defining the IP addresses). For applying the policy to addresses the port range/port number can be defined. The final steps require the policy permission to be set to either permit or deny access to the selected addresses or network resources. As well the policy can be specified for one or all of the supported SSL VPN services (i.e. VPN tunnel) Once defined, the policy goes into effect immediately. The policy name, SSL service it applies to, destination (network resource or IP addresses) and permission (deny/permit) is outlined in a list of configured policies for the router.
Unified Services Router User Manual 94 Figure 58: SSL VPN policy configuration 7.2.1 Using Network Resources Setup > VPN Settings > SSL VPN Server > Resources Network resources are services or groups of LAN IP addresses that are used to easily create and configure SSL VPN policies. This shortcut saves time when creating similar policies for multiple remote SSL VPN users. Adding a Network Resource involves creating a unique name to identify the resource and assigning it to one or all of the supported SSL services. Once this is done, editing one of the created network resources allows you to configure the object type (either IP address or IP range) associated with the service. The Network Address, Mask Length, and Port Range/Port Number can all be defined for this resource as required.
Unified Services Router User Manual 95 Figure 59: List of configured resources, which are available to assign to SSL VPN policies 7.3 Application Port Forwarding Setup > VPN Settings > SSL VPN Server > Port Forwarding Port forwarding allows remote SSL users to access specified network applications or services after they login to the User Portal and launch the Port Forwarding service. Traffic from the remote user to the router is detected and re-routed based on configured port forwarding rules. Internal host servers or TCP applications must be specified as being made accessible to remote users. Allowing access to a LAN server requires entering the local server IP address and TCP port number of the application to be tunneled. The table below lists some common applications and corresponding TCP port numbers: TCP Application Port Number FTP Data (usually not needed) 20 FTP Control Protocol 21 SSH 22 Telnet 23 SMTP (send mail) 25 HTTP (web) 80 POP3 (receive mail) 110 NTP (network time protocol) 123 Citrix 1494 Terminal Services 3389 VNC (virtual network computing) 5900 or 5800 As a convenience for remote users, the hostname (FQDN) of the network server can be configured to allow for IP address resolution. This host name resolution provides
Unified Services Router User Manual 96 users with easy-to-remember FQDN’s to access TCP applications instead of error-prone IP addresses when using the Port Forwarding service through the SSL User Portal.  Defining the hostname is optional as minimum requirement for port forwarding is identifying the TCP application and local server IP address. The local server IP address of the configured hostname must match the IP address of the configured application for port forwarding. Figure 60: List of Available Applications for SSL Port Forwarding 7.4 SSL VPN Client Configuration Setup > VPN Settings > SSL VPN Client > SSL VPN Client An SSL VPN tunnel client provides a point-to-point connection between the browser-side machine and this router. When a SSL VPN client is launched from the user portal, a "network adapter" with an IP address from the corporate subnet, DNS and WINS settings is automatically created. This allows local applications to access services on the private network without any special network configuration on the remote SSL VPN client machine. It is important to ensure that the virtual (PPP) interface address of the VPN tunnel client does not conflict with physical devices on the LAN. The IP address range for the SSL VPN virtual network adapter should be either in a different subnet or non-overlapping range as the corporate LAN.
Unified Services Router User Manual 97  The IP addresses of the client’s network interfaces (Ethernet, Wireless, etc.) cannot be identical to the router’s IP address or a server on the corporate LAN that is being accessed through the SSL VPN tunnel. Figure 61: SSL VPN client adapter and access configuration The router allows full tunnel and split tunnel support. Full tunnel mode just sends all traffic from the client across the VPN tunnel to the router. Split tunnel mode only sends traffic to the private LAN based on pre-specified client routes. These client routes give the SSL client access to specific private networks, thereby allowing access control over specific LAN services. Setup > VPN Settings > SSL VPN Client > Configured Client Routes If the SSL VPN client is assigned an IP address in a different subnet than the corporate network, a client route must be added to allow access to the private LAN through the VPN tunnel. As well a static route on the private LAN’s firewall (typically this router) is needed to forward private traffic through the VPN Firewall to the remote SSL VPN client.
Unified Services Router User Manual 98 Figure 62: Configured client routes only apply in split tunnel mode 7.5 User Portal Setup > VPN Settings > SSL VPN Client > SSL VPN Client Portal When remote users want to access the private network through an SSL tunnel (either using the Port Forwarding or VPN tunnel service), they login through a user portal. This portal provides the authentication fields to provide the appropriate access levels and privileges as determined by the router administrator. The domain where the user account is stored must be specified, and the domain determines the authentication method and portal layout screen presented to the remote user.
Unified Services Router User Manual 99 Figure 63: List of configured SSL VPN portals. The configured portal can then be associated with an authentication domain 7.5.1 Creating Portal Layouts Setup > VPN Settings > SSL VPN Server > Portal Layouts The router allows you to create a custom page for remote SSL VPN users that is presented upon authentication. There are various fields in the portal that are customizable for the domain, and this allows the router administrator to communicate details such as login instructions, available services, and other usage details in the portal visible to remote users. During domain setup, configured portal layouts are available to select for all users authenticated by the domain.  The default portal LAN IP address is https://192.168.10.1/scgi-bin/userPortal/portal. This is the same page that opens when the “User Portal” link is clicked on the SSL VPN menu of the router GUI. The router administrator creates and edits portal layouts from the configuration pages in the SSL VPN menu. The portal name, title, banner name, and banner contents are all customizable to the intended users for this portal. The portal name is appended to the SSL VPN portal URL. As well, the users assigned to this portal (through their authentication domain) can be presented with one or more of the router’s supported SSL services such as the VPN Tunnel page or Port Forwarding page.
Unified Services Router User Manual 100 Figure 64: SSL VPN Portal configuration
Unified Services Router User Manual 101 Chapter 8. Advanced Configuration Tools 8.1 USB Device Setup Setup > USB Settings There are two USB ports on the DSR Unified Services Router. The port supports a 3G modem where the USB dongle is used as a secondary WAN interface. Additionally, the port can be used for a USB storage device if USB Disc is type is selected. This storage can be accessed by LAN devices if appropriate policies are configured. Figure 65: USB device configuration 8.2 Authentication Certificates Advanced > Certificates This gateway uses digital certificates for IPSec VPN authentication as well as SSL validation (for HTTPS and SSL VPN authentication). You can obtain a digital certificate from a well known Certificate Authority (CA) such as VeriSign, or generate and sign your own certificate using functionality available on this gateway. The gateway comes with a self-signed certificate, and this can be replaced by one signed by a CA as per your networking requirements. A CA certificate provides strong assurance of the server’s identity and is a requirement for most corporate network VPN solutions. The certificates menu allows you to view a list of certificates (both from a CA and self-signed) currently loaded on the gateway. The following certificate data is displayed in the list of Trusted (CA) certificates: CA Identity (Subject Name): The certificate is issued to this person or organization Issuer Name: This is the CA name that issued this certificate Expiry Time: The date after which this Trusted certificate becomes invalid
Unified Services Router User Manual 102 A self certificate is a certificate issued by a CA identifying your device (or self-signed if you don’t want the identity protection of a CA). The Active Self Certificate table lists the self certificates currently loaded on the gateway. The following information is displayed for each uploaded self certificate: Name: The name you use to identify this certificate, it is not displayed to IPSec VPN peers or SSL users. Subject Name: This is the name that will be displayed as the owner of this certificate. This should be your official registered or company name, as IPSec or SSL VPN peers are shown this field. Serial Number: The serial number is maintained by the CA and used to identify this signed certificate. Issuer Name: This is the CA name that issued (signed) this certificate Expiry Time: The date after which this signed certificate becomes invalid – you should renew the certificate before it expires. To request a self certificate to be signed by a CA, you can generate a Certificate Signing Request from the gateway by entering identification parameters and passing it along to the CA for signing. Once signed, the CA’s Trusted Certificate and signed certificate from the CA are uploaded to activate the self-certificate validating the identity of this gateway. The self certificate is then used in IPSec and SSL connections with peers to validate the gateway’s authenticity. Figure 66: Certificate summary for IPSec and HTTPS management
Unified Services Router User Manual 103 Chapter 9. Administration & Management 9.1 Configuration Access Control The primary means to configure this gateway via the browser-independent GUI. The GUI can be accessed from LAN node by using the gateway’s LAN IP address and HTTP, or from the WAN by using the gateway’s WAN IP address and HTTPS (HTTP over SSL). Administrator and Guest users are permitted to login to the router’s management interface. The user type is set in the Advanced > Users > Users page. The Admin or Guest user can be configured to access the router GUI from the LAN or the Internet (WAN) by enabling the corresponding Login Policy. Figure 67: User Login policy configuration 9.1.1 Remote Management Both HTTPS and telnet access can be restricted to a subset of IP addresses. The router administrator can define a known PC, single IP address or range of IP addresses that are allowed to access the GUI with HTTPS. The opened port for SSL traffic can be changed from the default of 443 at the same time as defining the allowed remote management IP address range.
Unified Services Router User Manual 104 Figure 68: Remote Management from the WAN 9.1.2 CLI Access In addition to the web-based GUI, the gateway supports SSH and Telnet management for command-line interaction. The CLI login credentials are shared with the GUI for administrator users. To access the CLI, type “cli” in the SSH or console prompt and login with administrator user credentials. 9.2 SNMP Configuration Tools > Admin > SNMP SNMP is an additional management tool that is useful when multiple routers in a network are being managed by a central Master system. When an external SNMP manager is provided with this router’s Management Information Base (MIB) file, the manager can update the router’s hierarchal variables to view or update configuration parameters. The router as a managed device has an SNMP agent that allows the MIB configuration variables to be accessed by the Master (the SNMP manager). The Access Control List on the router identifies managers in the network that have read-only or read-write SNMP credentials. The Traps List outlines the port over which notifications from this router are provided to the SNMP community (managers) and also the SNMP version (v1, v2c, v3) for the trap.
Unified Services Router User Manual 105 Figure 69: SNMP Users, Traps, and Access Control Tools > Admin > SNMP System Info The router is identified by an SNMP manager via the System Information. The identifier settings The SysName set here is also used to identify the router for SysLog logging.
Unified Services Router User Manual 106 Figure 70: SNMP system information for this router 9.3 Configuring Time Zone and NTP Tools > Date and Time You can configure your time zone, whether or not to adjust for Daylight Savings Time, and with which Network Time Protocol (NTP) server to synchronize the date and time. You can choose to set Date and Time manually, which will store the information on the router’s real time clock (RTC). If the router has access to the internet, the most accurate mechanism to set the router time is to enable NTP server communication.  Accurate date and time on the router is critical for firewall schedules, Wi-Fi power saving support to disable APs at certain times of the day, and accurate logging. Please follow the steps below to configure the NTP server: 1. Select the router’s time zone, relative to Greenwich Mean Time (GMT). 2. If supported for your region, click to Enable Daylight Savings. 3. Determine whether to use default or custom Network Time Protocol (NTP) servers. If custom, enter the server addresses or FQDN.
Unified Services Router User Manual 107 Figure 71: Date, Time, and NTP server setup 9.4 Log Configuration This router allows you to capture log messages for traffic through the firewall, VPN, and over the wireless AP. As an administrator you can monitor the type of traffic that goes through the router and also be notified of potential attacks or errors when they are detected by the router. The following sections describe the log configuration settings and the ways you can access these logs. 9.4.1 Defining What to Log Tools > Log Settings > Logs Facility The Logs Facility page allows you to determine the granularity of logs to receive from the router. There are three core components of the router, referred to as Facilities: • Kernel: This refers to the Linux kernel. Log messages that correspond to this facility would correspond to traffic through the firewall or network stack.
Unified Services Router User Manual 108 • System: This refers to application and management level features available on this router, including SSL VPN and administrator changes for managing the unit. • Wireless: This facility corresponds to the 802.11 driver used for providing AP functionality to your network. For each facility, the following events (in order of severity) can be logged: Emergency, Alert, Critical, Error, Warning, Notification, Information, Debugging. When a particular severity level is selected, all events with severity equal to and greater than the chosen severity are captured. For example if you have configured CRITICAL level logging for the Wireless facility, then 802.11 logs with severities CRITICAL, ALERT, and EMERGENCY are logged. The severity levels available for logging are: • EMERGENCY: system is unusable • ALERT: action must be taken immediately • CRITICAL: critical conditions • ERROR: error conditions • WARNING: warning conditions • NOTIFICATION: normal but significant condition • INFORMATION: informational • DEBUGGING: debug-level messages
Unified Services Router User Manual 109 Figure 72: Facility settings for Logging The display for logging can be customized based on where the logs are sent, either the Event Log viewer in the GUI (the Event Log viewer is in the Status > Logs page) or a remote Syslog server for later review. E-mail logs, discussed in a subsequent section, follow the same configuration as logs configured for a Syslog server. Tools > Log Settings > Logs Configuration This page allows you to determine the type of traffic through the router that is logged for display in Syslog, E-mailed logs, or the Event Viewer. Denial of service attacks, general attack information, login attempts, dropped packets, and similar events can be captured for review by the IT administrator. Traffic through each network segment (LAN, WAN, DMZ) can be tracked based on whether the packet was accepted or dropped by the firewall. Accepted Packets are those that were successfully transferred through the corresponding network segment (i.e. LAN to WAN). This option is particularly useful when the Default Outbound Policy is “Block Always” so the IT admin can monitor traffic that is passed through the firewall.
Unified Services Router User Manual 110 • Example: If Accept Packets from LAN to WAN is enabled and there is a firewall rule to allow SSH traffic from LAN, then whenever a LAN machine tries to make an SSH connection, those packets will be accepted and a message will be logged. (Assuming the log option is set to Allow for the SSH firewall rule.) Dropped Packets are packets that were intentionally blocked from being transferred through the corresponding network segment. This option is useful when the Default Outbound Policy is “Allow Always”. • Example: If Drop Packets from LAN to WAN is enabled and there is a firewall rule to block ssh traffic from LAN, then whenever a LAN machine tries to make an ssh connection, those packets will be dropped and a message will be logged. (Make sure the log option is set to allow for this firewall rule.)  Enabling accepted packet logging through the firewall may generate a significant volume of log messages depending on the typical network traffic. This is recommended for debugging purposes only. In addition to network segment logging, unicast and multicast traffic can be logged. Unicast packets have a single destination on the network, whereas broadcast (or multicast) packets are sent to all possible destinations simultaneously. One other useful log control is to log packets that are dropped due to configured bandwidth profiles over a particular interface. This data will indicate to the admin whether the bandwidth profile has to be modified to account for the desired internet traffic of LAN users.
Unified Services Router User Manual 111 Figure 73: Log configuration options for traffic through router 9.4.2 Sending Logs to E-mail or Syslog Tools > Log Settings > Remote Logging Once you have configured the type of logs that you want the router to collect, they can be sent to either a Syslog server or an E-Mail address. For remote logging a key configuration field is the Remote Log Identifier. Every logged message will contain the configured prefix of the Remote Log Identifier, so that syslog servers or email addresses that receive logs from more than one router can sort for the relevant device’s logs. Once you enable the option to e-mail logs, enter the e-mail server’s address (IP address or FQDN) of the SMTP server. The router will connect to this server when sending e-mails out to the configured addresses. The SMPT port and return e-mail addresses are required fields to allow the router to package the logs and send a valid e-mail that is accepted by one of the configured “send-to” addresses. Up to three e-mail addresses can be configured as log recipients. In order to establish a connection with the configured SMTP port and server, define the server’s authentication requirements. The router supports Login Plain (no encryption) or CRAM-MD5 (encrypted) for the username and password data to be sent to the SMTP server. Authentication can be disabled if the server does not have
Unified Services Router User Manual 112 this requirement. In some cases the SMTP server may send out IDENT requests, and this router can have this response option enabled as needed. Once the e-mail server and recipient details are defined you can determine when the router should send out logs. E-mail logs can be sent out based on a defined schedule by first choosing the unit (i.e. the frequency) of sending logs: Hourly, Daily, or Weekly. Selecting Never will disable log e-mails but will preserve the e-mail server settings. Figure 74: E-mail configuration as a Remote Logging option An external Syslog server is often used by network administrator to collect and store logs from the router. This remote device typically has less memory constraints than
Unified Services Router User Manual 113 the local Event Viewer on the router’s GUI, and thus can collect a considerable number of logs over a sustained period. This is typically very useful for debugging network issues or to monitor router traffic over a long duration. This router supports up to 8 concurrent Syslog servers. Each can be configured to receive different log facility messages of varying severity. To enable a Syslog server select the checkbox next to an empty Syslog server field and assign the IP address or FQDN to the Name field. The selected facility and severity level messages will be sent to the configured (and enabled) Syslog server once you save this configuration page’s settings. Figure 75: Syslog server configuration for Remote Logging (continued) 9.4.3 Event Log Viewer in GUI Status > Logs > View All Logs The router GUI lets you observe configured log messages from the Status menu. Whenever traffic through or to the router matches the settings determined in the Tools > Log Settings > Logs Facility or Tools > Log Settings > Logs Configuration pages, the corresponding log message will be displayed in this window with a timestamp.  It is very important to have accurate system time (manually set or from a NTP server) in order to understand log messages. Status > Logs > VPN Logs This page displays IPSec VPN log messages as determined by the configuration settings for facility and severity. This data is useful when evaluating IPSec VPN traffic and tunnel health.
Unified Services Router User Manual 114 Figure 76: VPN logs displayed in GUI event viewer 9.5 Backing up and Restoring Configuration Settings Tools > System You can back up the router’s custom configuration settings to restore them to a different device or the same router after some other changes. During backup, your settings are saved as a file on your host. You can restore the router's saved settings from this file as well. This page will also allow you revert to factory default settings or execute a soft reboot of the router.  IMPORTANT! During a restore operation, do NOT try to go online, turn off the router, shut down the PC, or do anything else to the router until the operation is complete. This will take approximately 1 minute. Once the LEDs are turned off, wait a few more seconds before doing anything with the router. For backing up configuration or restoring a previously saved configuration, please follow the steps below: 1. To save a copy of your current settings, click the Backup button in the Save Current Settings option. The browser initiates an export of the configuration file and prompts to save the file on your host.
Unified Services Router User Manual 115 2. To restore your saved settings from a backup file, click Browse then locate the file on the host. After clicking Restore, the router begins importing the file’s saved configuration settings. After the restore, the router reboots automatically with the restored settings. 3. To erase your current settings and revert to factory default settings, click the Default button. The router will then restore configuration settings to factory defaults and will reboot automatically. (See Appendix B for the factory default parameters for the router). Figure 77: Restoring configuration from a saved file will result in the current configuration being overwritten and a reboot 9.6 Upgrading Router Firmware Tools > Firmware You can upgrade to a newer software version from the Administration web page. In the Firmware Upgrade section, to upgrade your firmware, click Browse, locate and select the firmware image on your host, and click Upgrade. After the new firmware image is validated, the new image is written to flash, and the router is automatically rebooted with the new firmware. The Firmware Information and also the Status > Device Info > Device Status page will reflect the new firmware version.  IMPORTANT! During firmware upgrade, do NOT try to go online, turn off the device, shut down the PC, or interrupt the process in anyway until the operation is complete. This should take only a minute or so including the reboot process. Interrupting the upgrade process at specific points when the flash is being written to may corrupt the flash memory and render the router unusable without a low-level process of restoring the flash firmware (not through the web GUI).
Unified Services Router User Manual 116 Figure 78: Firmware version information and upgrade option This router also supports an automated notification to determine if a newer firmware version is available for this router. By clicking the Check Now button in the notification section, the router will check a D-Link server to see if a newer firmware version for this router is available for download and update the Status field below. 9.7 Dynamic DNS Setup Tools > Dynamic DNS Dynamic DNS (DDNS) is an Internet service that allows routers with varying public IP addresses to be located using Internet domain names. To use DDNS, you must setup an account with a DDNS provider such as DynDNS.org, D-Link DDNS, or Oray.net. Each configured WAN can have a different DDNS service if required. Once configured, the router will update DDNS services changes in the WAN IP address so that features that are dependent on accessing the router’s WAN via FQDN will be directed to the correct IP address. When you set up an account with a DDNS service, the host and domain name, username, password and wildcard support will be provided by the account provider.
Unified Services Router User Manual 117 Figure 79: Dynamic DNS configuration 9.8 Using Diagnostic Tools Tools > System Check The router has built in tools to allow an administrator to evaluate the communication status and overall network health.
Unified Services Router User Manual 118 Figure 80: Router diagnostics tools available in the GUI 9.8.1 Ping This utility can be used to test connectivity between this router and another device on the network connected to this router. Enter an IP address and click PING. The command output will appear indicating the ICMP echo request status. 9.8.2 Trace Route This utility will display all the routers present between the destination IP address and this router. Up to 30 “hops” (intermediate routers) between this router and the destination will be displayed.
Unified Services Router User Manual 119 Figure 81: Sample traceroute output 9.8.3 DNS Lookup To retrieve the IP address of a Web, FTP, Mail or any other server on the Internet, type the Internet Name in the text box and click Lookup. If the host or domain entry exists, you will see a response with the IP address. A message stating “Unknown Host” indicates that the specified Internet Name does not exist.  This feature assumes there is internet access available on the WAN link(s). 9.8.4 Router Options The static and dynamic routes configured on this router can be shown by clicking Display for the corresponding routing table. Clicking the Packet Trace button will allow the router to capture and display traffic through the device between the LAN and WAN interface as well. This information is often very useful in debugging traffic and routing issues.
Unified Services Router User Manual 120 Chapter 10. Router Status and Statistics 10.1 System Overview The Status page allows you to get a detailed overview of the system configuration. The settings for the wired and wireless interfaces are displayed in the Device Status page, and then the resulting hardware resource and router usage details are summarized on the router’s Dashboard. 10.1.1 Device Status Status > Device Info > Device Status The Device Status page gives a summary of the router configuration settings configured in the Setup and Advanced menus. The static hardware serial number and current firmware version are presented in the General section. The WAN and LAN interface information shown on this page are based on the administrator configuration parameters. The radio band and channel settings are presented below along with all configured and active APs that are enabled on this router.
Unified Services Router User Manual 121 Figure 82: Device Status display
Unified Services Router User Manual 122 Figure 83: Device Status display (continued) 10.1.2 Resource Utilization Status > Device Info > Dashboard The Dashboard page presents hardware and usage statistics. The CPU and Memory utilization is a function of the available hardware and current configuration and traffic through the router. Interface statistics for the wired connections (LAN, WAN1, WAN2/DMZ, VLANs) provide indication of packets through and packets dropped by the interface. Click refresh to have this page retrieve the most current statistics.
Unified Services Router User Manual 123 Figure 84: Resource Utilization statistics
Unified Services Router User Manual 124
Unified Services Router User Manual 125 Figure 85: Resource Utilization data (continued)
Unified Services Router User Manual 126 Figure 86: Resource Utilization data (continued) 10.2 Traffic Statistics 10.2.1 Wired Port Statistics Status > Traffic Monitor > Device Statistics Detailed transmit and receive statistics for each physical port are presented here. Each interface (WAN1, WAN2/DMZ, LAN, and VLANs) have port specific packet level information provided for review. Transmitted/received packets, port collisions, and the cumulating bytes/sec for transmit/receive directions are provided for each interface along with the port up time. If you suspect issues with any of the wired ports, this table will help diagnose uptime or transmit level issues with the port. The statistics table has auto-refresh control which allows display of the most current port level data at each page refresh. The default auto-refresh for this page is 10 seconds.
Unified Services Router User Manual 127 Figure 87: Physical port statistics 10.2.2 Wireless Statistics Status > Traffic Monitor > Wireless Statistics The Wireless Statistics tab displays the incrementing traffic statistics for each enabled access point. This page will give a snapshot of how much traffic is being transmitted over each wireless link. If you suspect that a radio or VAP may be down, the details on this page would confirm if traffic is being sent and received through the VAP. The clients connected to a particular AP can be viewed by using the Status Button on the list of APs in the Setup > Wireless > Access Points page. Traffic statistics are shown for that individual AP, as compared to the summary stats for each AP on this Statistics page. The poll interval (the refresh rate for the statistics) can be modified to view more frequent traffic and collision statistics.
Unified Services Router User Manual 128 Figure 88: AP specific statistics 10.3 Active Connections 10.3.1 Sessions through the Router Status > Active Sessions This table lists the active internet sessions through the router’s firewall. The session’s protocol, state, local and remote IP addresses are shown.
Unified Services Router User Manual 129 Figure 89: List of current Active Firewall Sessions
Unified Services Router User Manual 130 10.3.2 Wireless Clients Status > Wireless Clients The clients connected to a particular AP can be viewed on this page. Connected clients are sorted by the MAC address and indicate the security parameters used by the wireless link, as well as the time connected to the corresponding AP. The statistics table has auto-refresh control which allows display of the most current port level data at each page refresh. The default auto-refresh for this page is 10 seconds. Figure 90: List of connected 802.11 clients per AP 10.3.3 LAN Clients Status > LAN Clients The LAN clients to the router are identified by an ARP scan through the LAN switch. The NetBios name (if available), IP address and MAC address of discovered LAN hosts are displayed.
Unified Services Router User Manual 131 Figure 91: List of LAN hosts 10.3.4 Active VPN Tunnels Status > Active VPNs You can view and change the status (connect or drop) of the router’s IPSec security associations. Here, the active IPSec SAs (security associations) are listed along with the traffic details and tunnel state. The traffic is a cumulative measure of transmitted/received packets since the tunnel was established. If a VPN policy state is “IPSec SA Not Established”, it can be enabled by clicking the Connect button of the corresponding policy. The Active IPSec SAs table displays a list of active IPSec SAs. Table fields are as follows. Field Description Policy Name IKE or VPN policy associated with this SA. Endpoint IP address of the remote VPN gateway or client. Tx (KB) Kilobytes of data transmitted over this SA. Tx (Packets) Number of IP packets transmitted over this SA. State Status of the SA for IKE policies: Not Connected or IPSec SA Established.
Unified Services Router User Manual 132 Figure 92: List of current Active VPN Sessions All active SSL VPN connections, both for VPN tunnel and VPN Port forwarding, are displayed on this page as well. Table fields are as follows. Field Description User Name The SSL VPN user that has an active tunnel or port forwarding session to this router. IP Address IP address of the remote VPN client. Local PPP Interface The interface (WAN1 or WAN2) through which the session is active. Peer PPP Interface IP The assigned IP address of the virtual network adapter. Connect Status Status of the SSL connection between this router and the remote VPN client: Not Connected or Connected.
Unified Services Router User Manual 133 Chapter 11. Trouble Shooting 11.1 Internet connection Symptom: You cannot access the router’s web-configuration interface from a PC on your LAN. Recommended action: 1. Check the Ethernet connection between the PC and the router. 2. Ensure that your PC’s IP address is on the same subnet as the router. If you are using the recommended addressing scheme, your PC’s address should be in the range 192.168.10.2 to 192.168.10.254. 3. Check your PC’s IP address. If the PC cannot reach a DHCP server, some versions of Windows and Mac OS generate and assign an IP address. These auto-generated addresses are in the range 169.254.x.x. If your IP address is in this range, check the connection from the PC to the firewall and reboot your PC. 4. If your router’s IP address has changed and you don’t know what it is, reset the router configuration to factory defaults (this sets the firewall’s IP address to 192.168.10.1). 5. If you do not want to reset to factory default settings and lose your configuration, reboot the router and use a packet sniffer (such as Ethereal™) to capture packets sent during the reboot. Look at the Address Resolution Protocol (ARP) packets to locate the router’s LAN interface address. 6. Launch your browser and ensure that Java, JavaScript, or ActiveX is enabled. If you are using Internet Explorer, click Refresh to ensure that the Java applet is loaded. Close the browser and launch it again. 7. Ensure that you are using the correct login information. The factory default login name is admin and the password is password. Ensure that CAPS LOCK is off when entering this information. Symptom: Router does not save configuration changes. Recommended action: 1. When entering configuration settings, click Apply before moving to another menu or tab; otherwise your changes are lost. 2. Click Refresh or Reload in the browser. Your changes may have been made, but the browser may be caching the old configuration.
Unified Services Router User Manual 134 Symptom: Router cannot access the Internet. Possible cause: If you use dynamic IP addresses, your router may not have requested an IP address from the ISP. Recommended action: 1. Launch your browser and go to an external site such as www.google.com. 2. Access the firewall’s configuration main menu at http://192.168.10.1. 3. Select Monitoring > Router Status. 4. Ensure that an IP address is shown for the WAN port. If 0.0.0.0 is shown, your firewall has not obtained an IP address from your ISP. See the next symptom. Symptom: Router cannot obtain an IP address from the ISP. Recommended action: 1. Turn off power to the cable or DSL modem. 2. Turn off the router. 3. Wait 5 minutes, and then reapply power to the cable or DSL modem. 4. When the modem LEDs indicate that it has resynchronized with the ISP, reapply power to the router. If the router still cannot obtain an ISP address, see the next symptom. Symptom: Router still cannot obtain an IP address from the ISP. Recommended action: 1. Ask your ISP if it requires a login program — PPP over Ethernet (PPPoE) or some other type of login. 2. If yes, verify that your configured login name and password are correct. 3. Ask your ISP if it checks for your PC's hostname. 4. If yes, select Network Configuration > WAN Settings > Ethernet ISP Settings and set the account name to the PC hostname of your ISP account. 5. Ask your ISP if it allows only one Ethernet MAC address to connect to the Internet, and therefore checks for your PC’s MAC address. 6. If yes, inform your ISP that you have bought a new network device, and ask them to use the firewall’s MAC address. 7. Alternatively, select Network Configuration > WAN Settings > Ethernet ISP Settings and configure your router to spoof your PC’s MAC address.
Unified Services Router User Manual 135 Symptom: Router can obtain an IP address, but PC is unable to load Internet pages. Recommended action: 1. Ask your ISP for the addresses of its designated Domain Name System (DNS) servers. Configure your PC to recognize those addresses. For details, see your operating system documentation. 2. On your PC, configure the router to be its TCP/IP gateway. 11.2 Date and time Symptom: Date shown is January 1, 1970. Possible cause: The router has not yet successfully reached a network time server (NTS). Recommended action: 1. If you have just configured the router, wait at least 5 minutes, select Administration > Time Zone, and recheck the date and time. 2. Verify your Internet access settings. Symptom: Time is off by one hour. Possible cause: The router does not automatically adjust for Daylight Savings Time. Recommended action: 1. Select Administration > Time Zone and view the current date and time settings. 2. Click to check or uncheck “Automatically adjust for Daylight Savings Time”, then click Apply. 11.3 Pinging to Test LAN Connectivity Most TCP/IP terminal devices and firewalls contain a ping utility that sends an ICMP echo-request packet to the designated device. The device responds with an echo reply. Troubleshooting a TCP/IP network is made very easy by using the ping utility in your PC or workstation. 11.3.1 Testing the LAN path from your PC to your router 1. From the PC’s Windows toolbar, select Start > Run. 2. Type ping <IP_address> where <IP_address> is the router’s IP address. Example: ping 192.168.10.1. 3. Click OK.
Unified Services Router User Manual 136 4. Observe the display: • If the path is working, you see this message sequence: Pinging <IP address> with 32 bytes of data Reply from <IP address>: bytes=32 time=NN ms TTL=xxx • If the path is not working, you see this message sequence: Pinging <IP address> with 32 bytes of data Request timed out 5. If the path is not working, Test the physical connections between PC and router • If the LAN port LED is off, go to the “LED displays” section on page B-1 and follow instructions for “LAN or Internet port LEDs are not lit.” • Verify that the corresponding link LEDs are lit for your network interface card and for any hub ports that are connected to your workstation and firewall. 6. If the path is still not up, test the network configuration: • Verify that the Ethernet card driver software and TCP/IP software are installed and configured on the PC. • Verify that the IP address for the router and PC are correct and on the same subnet. 11.3.2 Testing the LAN path from your PC to a remote device 1. From the PC’s Windows toolbar, select Start > Run. 2. Type ping -n 10 <IP_address> where -n 10 specifies a maximum of 10 tries and <IP address> is the IP address of a remote device such as your ISP’s DNS server. Example: ping -n 10 10.1.1.1. 3. Click OK and then observe the display (see the previous procedure). 4. If the path is not working, do the following: • Check that the PC has the IP address of your firewall listed as the default gateway. (If the IP configuration of your PC is assigned by DHCP, this information is not visible in your PC’s Network Control Panel.)
Unified Services Router User Manual 137 • Verify that the network (subnet) address of your PC is different from the network address of the remote device. • Verify that the cable or DSL modem is connected and functioning. • Ask your ISP if it assigned a hostname to your PC. If yes, select Network Configuration > WAN Settings > Ethernet ISP Settings and enter that hostname as the ISP account name. • Ask your ISP if it rejects the Ethernet MAC addresses of all but one of your PCs. Many broadband ISPs restrict access by allowing traffic from the MAC address of only your broadband modem; but some ISPs additionally restrict access to the MAC address of just a single PC connected to that modem. If this is the case, configure your firewall to clone or spoof the MAC address from the authorized PC. 11.4 Restoring factory-default configuration settings To restore factory-default configuration settings, do either of the following: 1. Do you know the account password and IP address? • If yes, select Administration > Settings Backup & Upgrade and click default. • If no, do the following: On the rear panel of the router, press and hold the Reset button about 10 seconds, until the test LED lights and then blinks. Release the button and wait for the router to reboot. 2. If the router does not restart automatically; manually restart it to make the default settings effective. 3. After a restore to factory defaults —whether initiated from the configuration interface or the Reset button — the following settings apply: • LAN IP address: 192.168.10.1 • Username: admin • Password: password • DHCP server on LAN: enabled • WAN port configuration: Get configuration via DHCP
Chapter 12. Credits Microsoft, Windows are registered trademarks of Microsoft Corp. Linux is a registered trademark of Linus Torvalds. UNIX is a registered trademark of The Open Group.
Unified Services Router User Manual 140 Appendix A. Glossary ARP Address Resolution Protocol. Broadcast protocol for mapping IP addresses to MAC addresses. CHAP Challenge-Handshake Authentication Protocol. Protocol for authenticating users to an ISP. DDNS Dynamic DNS. System for updating domain names in real time. Allows a domain name to be assigned to a device with a dynamic IP address. DHCP Dynamic Host Configuration Protocol. Protocol for allocating IP addresses dynamically so that addresses can be reused when hosts no longer need them. DNS Domain Name System. Mechanism for translating H.323 IDs, URLs, or e-mail IDs into IP addresses. Also used to assist in locating remote gatekeepers and to map IP addresses to hostnames of administrative domains. FQDN Fully qualified domain name. Complete domain name, including the host portion. Example: serverA.companyA.com. FTP File Transfer Protocol. Protocol for transferring files between network nodes. HTTP Hypertext Transfer Protocol. Protocol used by web browsers and web servers to transfer files. IKE Internet Key Exchange. Mode for securely exchanging encryption keys in ISAKMP as part of building a VPN tunnel. IPSec IP security. Suite of protocols for securing VPN tunnels by authenticating or encrypting IP packets in a data stream. IPSec operates in either transport mode (encrypts payload but not packet headers) or tunnel mode (encrypts both payload and packet headers). ISAKMP Internet Key Exchange Security Protocol. Protocol for establishing security associations and cryptographic keys on the Internet. ISP Internet service provider. MAC Address Media-access-control address. Unique physical-address identifier attached to a network adapter. MTU Maximum transmission unit. Size, in bytes, of the largest packet that can be passed on. The MTU for Ethernet is a 1500-byte packet. NAT Network Address Translation. Process of rewriting IP addresses as a packet passes through a router or firewall. NAT enables multiple hosts on a LAN to access the Internet using the single public IP address of the LAN’s gateway router. NetBIOS Microsoft Windows protocol for file sharing, printer sharing, messaging, authentication, and name resolution. NTP Network Time Protocol. Protocol for synchronizing a router to a single clock on the network, known as the clock master. PAP Password Authentication Protocol. Protocol for authenticating users to a remote access server or ISP.
Unified Services Router User Manual 141 PPPoE Point-to-Point Protocol over Ethernet. Protocol for connecting a network of hosts to an ISP without the ISP having to manage the allocation of IP addresses. PPTP Point-to-Point Tunneling Protocol. Protocol for creation of VPNs for the secure transfer of data from remote clients to private servers over the Internet. RADIUS Remote Authentication Dial-In User Service. Protocol for remote user authentication and accounting. Provides centralized management of usernames and passwords. RSA Rivest-Shamir-Adleman. Public key encryption algorithm. TCP Transmission Control Protocol. Protocol for transmitting data over the Internet with guaranteed reliability and in-order delivery. UDP User Data Protocol. Protocol for transmitting data over the Internet quickly but with no guarantee of reliability or in-order delivery. VPN Virtual private network. Network that enables IP traffic to travel securely over a public TCP/IP network by encrypting all traffic from one network to another. Uses tunneling to encrypt all information at the IP level. WINS Windows Internet Name Service. Service for name resolution. Allows clients on different IP subnets to dynamically resolve addresses, register themselves, and browse the network without sending broadcasts. XAUTH IKE Extended Authentication. Method, based on the IKE protocol, for authenticating not just devices (which IKE authenticates) but also users. User authentication is performed after device authentication and before IPSec negotiation.
Appendix B. Factory Default Settings Feature Description Default Setting Device login User login URL http://192.168.10.1 User name (case sensitive) admin Login password (case sensitive) admin Internet Connection WAN MAC address Use default address WAN MTU size 1500 Port speed Autosense Local area network (LAN) IP address 192.168.10.1 IPv4 subnet mask 255.255.255.0 RIP direction None RIP version Disabled RIP authentication Disabled DHCP server Enabled DHCP starting IP address 192.168.10.2 DHCP ending IP address 192.168.10.100 Time zone GMT Time zone adjusted for Daylight Saving Time Disabled SNMP Disabled Remote management Disabled Firewall Inbound communications from the Internet Disabled (except traffic on port 80, the HTTP port) Outbound communications to the Internet Enabled (all) Source MAC filtering Disabled Stealth mode Enabled
Unified Services Router User Manual 144 Appendix C. Standard Services Available for Port Forwarding & Firewall Configuration ANY AIM BGP BOOTP_CLIENT BOOTP_SERVER CU-SEEME:UDP CU-SEEME:TCP DNS:UDP DNS:TCP FINGER FTP HTTP HTTPS ICMP-TYPE-3 ICMP-TYPE-4 ICMP-TYPE-5 ICMP-TYPE-6 ICMP-TYPE-7 ICMP-TYPE-8 ICMP-TYPE-9 ICMP-TYPE-10 ICMP-TYPE-11 ICMP-TYPE-13 ICQ IMAP2 IMAP3 IRC NEWS NFS NNTP PING POP3 PPTP RCMD REAL-AUDIO REXEC RLOGIN RTELNET RTSP:TCP RTSP:UDP SFTP SMTP SNMP:TCP SNMP:UDP SNMP-TRAPS:TCP SNMP-TRAPS:UDP SQL-NET SSH:TCP SSH:UDP STRMWORKS TACACS TELNET TFTP VDOLIVE
Unified Services Router User Manual 145 Appendix D. Log Output Reference Facility: System (Networking) Log Message Severity Log Message Severity DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG BridgeConfig: too few arguments to command %s ERROR networkIntable.txt not found DEBUG BridgeConfig: too few arguments to command %s ERROR sqlite3QueryResGet failed DEBUG sqlite3QueryResGet failed.Query:%s ERROR Interface is already deleted in bridge DEBUG ddnsDisable failed ERROR removing %s from bridge %s... %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR adding %s to bridge %s... %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR stopping bridge... DEBUG ddnsDisable failed ERROR stopping bridge... DEBUG failed to call ddns enable ERROR stopping bridge... DEBUG ddnsDisable failed ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG sqlite3QueryResGet failed.Query:%s ERROR Wan is not up DEBUG Error in executing DB update handler ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG sqlite3QueryResGet failed.Query:%s ERROR doDNS:failed DEBUG Illegal invocation of ddnsView (%s) ERROR doDNS:failed DEBUG sqlite3QueryResGet failed.Query:%s ERROR doDNS:Result = FAILED DEBUG sqlite3QueryResGet failed.Query:%s ERROR doDNS:Result SUCCESS DEBUG ddns: SQL error: %s ERROR Write Old Entry: %s %s %s: to %s DEBUG Illegal operation interface got deleted ERROR Write New Entry: %s %s #%s : to %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Write Old Entry: %s %s %s: to %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Write New Entry: %s %s #%s : to %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR ifStaticMgmtDBUpdateHandler: returning with " DEBUG ddnsDisable failed ERROR nimfLinkStatusGet: buffer: \ DEBUG ddns: SQL error: %s ERROR nimfLinkStatusGetErr: returning with status: %d DEBUG Failed to call ddns enable ERROR nimfAdvOptSetWrap: current Mac Option: %d DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: current Port Speed Option: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: current Mtu Option: %d DEBUG Failed to call ddns enable ERROR nimfAdvOptSetWrap: looks like we are reconnecting. " DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: Mtu Size: %d DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: NIMF table is %s DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap:WAN_MODE TRIGGER DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: MTU: %d DEBUG Failed to call ddns enable ERROR nimfAdvOptSetWrap: MacAddress: %s DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: old Mtu Flag: %d DEBUG ddnsDisable failed ERROR
Unified Services Router User Manual 146 nimfAdvOptSetWrap: user has changed MTU option DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: MTU: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: old MTU size: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfAdvOptSetWrap: old Port Speed Option: %d DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: old Mac Address Option: %d DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: MacAddress: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Setting LED [%d]:[%d] For %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR l2tpEnable: command string: %s DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: handling reboot scenario DEBUG failed to call ddns enable ERROR nimfAdvOptSetWrap: INDICATOR = %d DEBUG ddns: SQL error: %s ERROR nimfAdvOptSetWrap: UpdateFlag: %d DEBUG ddnsDisable failed ERROR nimfAdvOptSetWrap: returning with status: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfGetUpdateMacFlag: MacTable Flag is: %d DEBUG Error in executing DB update handler ERROR nimfMacGet: Mac Option changed DEBUG Failed to open the resolv.conf file. Exiting./n ERROR nimfMacGet: Update Flag: %d DEBUG Could not write to the resolv.conf file. Exiting. ERROR nimfMacGet: MacAddress: %s DEBUG Error opening the lanUptime File ERROR nimfMacGet: MacAddress: %s DEBUG Error Opening the lanUptime File. ERROR nimfMacGet: MacAddress: %s DEBUG failed to open %s ERROR nimfMacGet: MacAddress: %s DEBUG failed to open %s ERROR nimfMacGet: MacAddress: %s DEBUG failed to query networkInterface table ERROR nimfMacGet:Mac option Not changed \ DEBUG failed to query networkInterface table ERROR nimfMacGet: MacAddress: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR nimfMacGet: MacAddress: %s DEBUG failed to enable IPv6 forwarding ERROR nimfMacGet: MacAddress: %s DEBUG failed to set capabilities on the " ERROR nimfMacGet: returning with status: %s DEBUG failed to enable IPv6 forwarding ERROR Now in enableing LanBridge function DEBUG failed to set capabilities on the " ERROR sucessfully executed the command %s DEBUG failed to disable IPv6 forwarding ERROR Now in disableing LanBridge function DEBUG failed to set capabilities on the " ERROR sucessfully executed the command %s DEBUG failed to open %s ERROR configPortTblHandler:Now we are in Sqlite Update " DEBUG Could not create ISATAP Tunnel ERROR The Old Configuration of ConfiPort was:%s DEBUG Could not destroy ISATAP Tunnel ERROR The New Configuration of ConfiPort was:%s DEBUG Could not configure ISATAP Tunnel ERROR The user has deselected the configurable port DEBUG Could not de-configure ISATAP Tunnel ERROR failed query %s DEBUG nimfStatusUpdate: updating NimfStatus failed ERROR failed query %s DEBUG nimfStatusUpdate: updating NimfStatus failed ERROR failed query %s DEBUG nimfLinkStatusGet: determinig link's status failed ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG nimfLinkStatusGet: opening status file failed ERROR
Unified Services Router User Manual 147 %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG Failed to commit ERROR %s:%d SIP ENABLE: %s DEBUG ifStatusDBUpdate: Failed to begin " ERROR sipTblHandler:failed to update ifStatic DEBUG %s: SQL error: %s ERROR sipTblHandler:failed to update Configport DEBUG %s: Failed to commit " ERROR %s:%d SIP DISABLE: %s DEBUG nimfNetIfaceTblHandler: unable to get LedPinId ERROR %s:%d SIP SET CONF: %s DEBUG nimfNetIfaceTblHandler: unable to get LedPinId ERROR Failed to open %s: %s DEBUG nimfNetIfaceTblHandler: unable to get LedPinId ERROR Failed to start sipalg DEBUG %s: unable to kill dhclient ERROR Failed to stop sipalg DEBUG nimfAdvOptSetWrap: unable to get current Mac Option ERROR Failed to get config info DEBUG nimfAdvOptSetWrap: unable to get current Port " ERROR Network Mask: 0x%x DEBUG nimfAdvOptSetWrap: unable to get current MTU Option ERROR RTP DSCP Value: 0x%x DEBUG nimfAdvOptSetWrap: error getting Mac Address from " ERROR Need more arguments DEBUG nimfAdvOptSetWrap: unable to get the MTU ERROR Invalid lanaddr DEBUG nimfAdvOptSetWrap: error setting interface advanced " ERROR Invalid lanmask DEBUG nimfAdvOptSetWrap: error getting MTU size ERROR Invalid option DEBUG nimfAdvOptSetWrap: unable to get Mac Address ERROR Failed to set config info DEBUG nimfAdvOptSetWrap: error setting interface advanced " ERROR Unknown option DEBUG nimfAdvOptSetWrap: failed to get old connectiontype ERROR sshdTblHandler DEBUG nimfAdvOptSetWrap: old connection type is: %s ERROR pPort: %s DEBUG nimfAdvOptSetWrap: failed to get old MTU Option ERROR pProtocol: %s DEBUG nimfAdvOptSetWrap: error getting MTU size ERROR pListerAddr: %s DEBUG nimfOldFieldValueGet: failed to get old " ERROR pKeyBits: %s DEBUG nimfOldFieldValueGet: user has changed MTU size ERROR pRootEnable: %s DEBUG nimfAdvOptSetWrap: failed to get old Port Speed " ERROR pRsaEnable: %s DEBUG nimfAdvOptSetWrap: user has changed Port Speed ERROR pDsaEnable: %s DEBUG nimfAdvOptSetWrap: failed to get old Mac Address " ERROR pPassEnable: %s DEBUG nimfAdvOptSetWrap: user has changed Mac Address " ERROR pEmptyPassEnable: %s DEBUG nimfAdvOptSetWrap: unable to get Mac Address ERROR pSftpEnable: %s DEBUG nimfAdvOptSetWrap:Failed to RESET the flag ERROR pScpEnable: %s DEBUG nimfAdvOptSetWrap: setting advanced options failed ERROR pSshdEnable: %s DEBUG nimfAdvOptSetWrap: interface advanced options applied ERROR
Unified Services Router User Manual 148 pPrivSep: %s DEBUG nimfGetUpdateMacFlag: unable to get Flag from MacTable ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG nimfMacGet: Updating MAC address failed ERROR Re-Starting sshd daemon.... DEBUG sqlite3QueryResGet failed.Query:%s ERROR sshd re-started successfully. DEBUG error executing the command %s ERROR sshd stopped . DEBUG error executing the command %s ERROR failed query %s DEBUG error executing the command %s ERROR vlan disabled, not applying vlan configuration.. DEBUG disableLan function is failed to disable ConfigPort" ERROR failed query %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR failed query %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR no ports present in this vlanId %d DEBUG Unable to Disable configurable port from ERROR failed query %s DEBUG configPortTblHandler has failed ERROR vlan disabled, not applying vlan configuration.. DEBUG sqlite3QueryResGet failed.Query:%s ERROR disabling vlan DEBUG Error in executing DB update handler ERROR enabling vlan DEBUG sqlite3QueryResGet failed ERROR vlan disabled, not applying vlan configuration.. DEBUG Failed to execute switchConfig for port\ ERROR no ports present in this vlanId %d DEBUG Failed to execute switchConfig for port enable ERROR failed query %s DEBUG Failed to execute ifconfig for port enable ERROR vlan disabled, not applying vlan configuration.. DEBUG Failed to execute ethtool for\ ERROR removing %s from bridge%s... %s DEBUG Failed to execute switchConfig for port disable ERROR adding %s to bridge%d... %s DEBUG Failed to execute ifconfig for port disable ERROR restarting bridge... DEBUG sqlite3QueryResGet failed ERROR [switchConfig] Ignoring event on port number %d DEBUG sqlite3_mprintf failed ERROR restarting bridge... DEBUG sqlite3QueryResGet failed ERROR executing %s ... %s DEBUG Failed to execute switchConfig for port mirroring ERROR removing %s from bridge%s... %s DEBUG Usage:%s <DB Name> <Entry Name> <logFile> <subject> ERROR adding %s to bridge%d... %s DEBUG sqlite3QueryResGet failed ERROR [switchConfig] Ignoring event on %s DEBUG Could not get all the required variables to email the Logs. ERROR restarting bridge... DEBUG runSmtpClient failed ERROR [switchConfig] Ignoring event on port number %d DEBUG getaddrinfo returned %s ERROR [switchConfig] executing %s ... %s DEBUG file not found ERROR restarting bridge... DEBUG sqlite3QueryResGet failed.Query:%s ERROR UserName: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Password: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR IspName: %s DEBUG No memory to allocate ERROR DialNumber: %s DEBUG Failed to Open SSHD Configuration File ERROR Apn: %s DEBUG Ipaddress should be provided with accessoption 1 ERROR
Unified Services Router User Manual 149 GetDnsFromIsp: %s DEBUG Subnetaddress should be provided with accessoption 2 ERROR IdleTimeOutFlag: %s DEBUG Failed to restart sshd ERROR IdleTimeOutValue: %d DEBUG unable to open the " ERROR AuthMetho: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR executing %s ... %s DEBUG Error in executing DB update handler ERROR removing %s from bridge%d... %s DEBUG Error in executing DB update handler ERROR adding %s to bridge%d... %s DEBUG unknown vlan state ERROR stopping bridge... DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR restarting bridge... DEBUG sqlite3_mprintf failed ERROR Could not configure 6to4 Tunnel Interface DEBUG Access port can be present only in single vlan ERROR Could not de-configure 6to4 Tunnel Interface DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR failed to restart 6to4 tunnel interfaces DEBUG unknown vlan state ERROR BridgeConfig: too few arguments to command %s DEBUG Failed to execute vlanConfig binary for port number %d ERROR BridgeConfig: unsupported command %d DEBUG Failed to clear vlan for oldPVID %d ERROR BridgeConfig returned error=%d DEBUG Failed to execute vlanConfig binary for port number %d ERROR sqlite3QueryResGet failed DEBUG Failed to clear vlan for %d ERROR Error in executing DB update handler DEBUG Failed to set vlan entry for vlan %d ERROR sqlite3QueryResGet failed DEBUG Failed to set vlan entries, while enabling \ ERROR Failed to remove vlan Interface for vlanId \ DEBUG sqlite3QueryResGet failed ERROR sqlite3QueryResGet failed DEBUG Failed to execute vlanConfig binary for port number %d ERROR Invalid oidp passed DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR Invalid oidp passed DEBUG Failed to enable vlan ERROR Failed to get oid from the tree DEBUG Failed to disable vlan ERROR threegEnable: Input to wrapper %s DEBUG Failed to set vlanPort table entries, while \ ERROR threegEnable: spawning command %s DEBUG Failed to enable vlan ERROR threegMgmtHandler: query string: %s DEBUG unknown vlan state ERROR threegMgmtHandler: returning with status: %s DEBUG Error in executing DB update handler ERROR adding to dhcprealy ifgroup failed DEBUG unknown vlan state ERROR adding to ipset fwDhcpRelay failed DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR Disabling Firewall Rule for DHCP Relay Protocol DEBUG sqlite3_mprintf failed ERROR Enabling Firewall Rule for DHCP Relay Protocol DEBUG Access port can be present only in single vlan ERROR prerouting Firewall Rule add for Relay failed DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR prerouting Firewall Rule add for Relay failed DEBUG unknown vlan state ERROR %s: SQL get query: %s DEBUG Failed to execute vlanConfig binary for port number %d ERROR %s: sqlite3QueryResGet failed DEBUG Failed to clear vlan for oldPVID %d ERROR %s: no result found DEBUG Failed to execute vlanConfig binary for port number %d ERROR
Unified Services Router User Manual 150 %s: buffer overflow DEBUG Failed to clear vlan for %d ERROR %s: value of %s in %s table is: %s DEBUG Failed to set vlan entry for vlan %d ERROR %s: returning with status: %s DEBUG Failed to set vlan entries, while enabling \ ERROR dnsResolverConfigure: addressFamily: %d DEBUG Failed to execute vlanConfig binary for port number %d ERROR dnsResolverConfigure: LogicalIfName: %s DEBUG Failed to execute vlanConfig binary for vlanId %d ERROR chap-secrets File found DEBUG Failed to enable vlan ERROR PID File for xl2tpd found DEBUG Failed to disable vlan ERROR pid: %d DEBUG Failed to set vlanPort table entries, while \ ERROR options.xl2tpd file found DEBUG Failed to enable vlan ERROR options.xl2tpd file not found DEBUG unknown vlan state ERROR Conf File for xl2tpd found DEBUG threegMgmtInit: unable to open the database file %s ERROR xl2tpd.conf not found DEBUG threegConnEnable: failed to get the WanMode ERROR Chap Secrets file found DEBUG threegEnable:spawning failed ERROR Chap Secrets file not found DEBUG threegDisable: unable to kill ppp daemon ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG threegMgmtHandler: Query: %s ERROR chap-secrets File found DEBUG threegMgmtHandler: error in executing database update ERROR PID File for pptpd found DEBUG Error in executing DB update handler ERROR pid: %d DEBUG are we getting invoked twice ?? ERROR PID File for pptpd interface found DEBUG could not open %s to append ERROR pid: %d DEBUG could not write nameserver %s to %s ERROR options.pptpd file found DEBUG could not write nameserver %s to %s ERROR options.pptpd file not found DEBUG could not open %s to truncate ERROR Conf File for pptpd found DEBUG dnsResolverConfigMgmtInit: unable to open the " ERROR pptpd.conf not found DEBUG resolverConfigDBUpateHandler: sqlite3QueryResGet " ERROR Chap Secrets file found DEBUG could not configure DNS resolver ERROR Chap Secrets file not found DEBUG dnsResolverConfigure: could not write nameserver:%s," ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG unboundMgmt: unable to open the " ERROR chap-secrets File found DEBUG ioctl call Failed-could not update active user Details ERROR pppoeMgmtTblHandler: MtuFlag: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR pppoeMgmtTblHandler: Mtu: %d DEBUG Can't kill xl2tpd ERROR pppoeMgmtTblHandler: IdleTimeOutFlag: %d DEBUG xl2tpd restart failed ERROR pppoeMgmtTblHandler: IdleTimeOutValue: %d DEBUG failed to get field value ERROR pppoeMgmtTblHandler: UserName: %s DEBUG failed to get field value ERROR pppoeMgmtTblHandler: Password: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR pppoeMgmtTblHandler: DNS specified: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR pppoeMgmtTblHandler: Service: %s DEBUG unboundMgmt: unable to open the " ERROR pppoeMgmtTblHandler: StaticIp: %s DEBUG writing options.xl2tpd failed ERROR
Unified Services Router User Manual 151 pppoeMgmtTblHandler: NetMask: %s DEBUG xl2tpdStop failed ERROR pppoeMgmtTblHandler: AuthOpt: %d DEBUG writing xl2tpd.conf failed ERROR pppoeMgmtTblHandler: Satus: %d DEBUG writing options.xl2tpd failed ERROR pppoeEnable: ppp dial string: %s DEBUG xl2tpdStop failed ERROR pppoeMgmtDBUpdateHandler: returning with status: %s DEBUG xl2tpdStart failed ERROR pptpMgmtTblHandler: MtuFlag: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR pptpMgmtTblHandler: Mtu: %d DEBUG writing Chap-secrets/Pap-Secrets failed ERROR pptpMgmtTblHandler: IdleTimeOutFlag: %d DEBUG xl2tpdStop failed ERROR pptpMgmtTblHandler: IdleTimeOutValue: %d DEBUG xl2tpdStart failed ERROR pptpMgmtTblHandler: GetDnsFromIsp: %d DEBUG sqlite3QueryResGet failed.Query:%s ERROR pptpMgmtTblHandler: UserName: %s DEBUG writing Chap-secrets/Pap-Secrets failed ERROR pptpMgmtTblHandler: Password: %s DEBUG xl2tpdStop failed ERROR pptpMgmtTblHandler: dynamic MyIp configured DEBUG xl2tpdStart failed ERROR pptpMgmtTblHandler: MyIp: %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR pptpMgmtTblHandler: ServerIp: %s DEBUG writing Chap-secrets/Pap-Secrets failed ERROR pptpMgmtTblHandler: StaticIp: %s DEBUG Error in executing DB update handler ERROR pptpMgmtTblHandler: NetMask: %s DEBUG unboundMgmt: unable to open the " ERROR pptpMgmtTblHandler: MppeEncryptSupport: %s DEBUG Can't kill pptpd ERROR pptpMgmtTblHandler: SplitTunnel: %s DEBUG pptpd restart failed ERROR pptpEnable: ppp dial string: %s DEBUG Can't kill pptpd ERROR pptpEnable: spawning command %s DEBUG failed to get field value ERROR PID File for dhcpc found DEBUG failed to get field value ERROR pid: %d DEBUG unboundMgmt: unable to open the " ERROR pptpMgmtDBUpdateHandler: query string: %s DEBUG writing options.pptpd failed ERROR pptpMgmtDBUpdateHandler: returning with status: %s DEBUG pptpdStop failed ERROR dhcpcReleaseLease: dhcpc release command: %s DEBUG writing pptpd.conf failed ERROR dhcpcMgmtTblHandler: MtuFlag: %d DEBUG writing options.pptpd failed ERROR dhcpcMgmtTblHandler: Mtu: %d DEBUG pptpdStop failed ERROR DHCPv6 Server started successfully. DEBUG pptpdStart failed ERROR DHCPv6 Server stopped successfully DEBUG writing Chap-secrets/Pap-Secrets failed ERROR DHCPv6 Client started successfully. DEBUG Error in executing DB update handler ERROR DHCPv6 Client stopped successfully. DEBUG pppStatsUpdate: unable to get default MTU ERROR DHCPv6 Client Restart successful DEBUG pppoeMgmtInit: unable to open the database file %s ERROR l2tpMgmtTblHandler: MtuFlag: %d DEBUG pppoeDisable: unable to kill ppp daemon ERROR l2tpMgmtTblHandler: Mtu: %d DEBUG pppoeMultipleEnableDisable: pppoe enable failed ERROR l2tpMgmtTblHandler: IspName: %s DEBUG pppoeMultipleEnableDisable: pppoe disable failed ERROR
Unified Services Router User Manual 152 l2tpMgmtTblHandler: UserName: %s DEBUG pppoeMgmtTblHandler: unable to get current Mtu Option ERROR l2tpMgmtTblHandler: Password: %s DEBUG pppoeMgmtTblHandler: unable to get the Mtu ERROR l2tpMgmtTblHandler: AccountName: %s DEBUG pppoeMgmtTblHandler: pppoe enable failed ERROR l2tpMgmtTblHandler: DomainName: %s DEBUG pppoeMgmtDBUpdateHandler: failed query: %s ERROR l2tpMgmtTblHandler: Secret: not specified DEBUG pppoeMgmtDBUpdateHandler: error in executing " ERROR l2tpMgmtTblHandler: Secret: %s DEBUG pptpMgmtInit: unable to open the database file %s ERROR l2tpMgmtTblHandler: dynamic MyIp configured DEBUG pptpEnable: error executing command: %s ERROR l2tpMgmtTblHandler: MyIp: %s DEBUG pptpEnable: unable to resolve address: %s ERROR l2tpMgmtTblHandler: ServerIp: %s DEBUG pptpEnable: inet_aton failed ERROR l2tpMgmtTblHandler: StaticIp: %s DEBUG pptpEnable: inet_aton failed ERROR l2tpMgmtTblHandler: NetMask: %s DEBUG pptpEnable:spawning failed ERROR l2tpMgmtTblHandler: SplitTunnel: %s DEBUG pptpDisable: unable to kill ppp daemon ERROR needToStartHealthMonitor: returning with status: %s DEBUG pptpMgmtTblHandler: unable to get current MTU Option ERROR l2tpEnable: command string: %s DEBUG pptpMgmtTblHandler: unable to get the Mtu ERROR l2tpEnable: command: %s DEBUG pptpMgmtTblHandler: dbRecordValueGet failed for %s " ERROR l2tpEnable: command string: %s DEBUG pptpMgmtTblHandler: pptp enable failed ERROR PID File for dhcpc found DEBUG pptpMgmtTblHandler: pptp disable failed ERROR pid: %d DEBUG pptpMgmtDBUpdateHandler: sqlite3QueryResGet " ERROR l2tpMgmtDBUpdateHandler: query string: %s DEBUG pptpMgmtDBUpdateHandler: error in executing " ERROR l2tpMgmtDBUpdateHandler: returning with status: %s DEBUG Illegal invocation of dhcpConfig (%s) ERROR RADVD started successfully DEBUG dhcpLibInit: unable to open the database file %s ERROR RADVD stopped successfully DEBUG sqlite3QueryResGet failed.Query:%s ERROR empty update. nRows=%d nCols=%d WARN dhcpcMgmtInit: unable to open the database file %s ERROR Wan is not up or in load balencing mode WARN dhcpcReleaseLease: unable to release lease ERROR threegMgmtHandler: no row found. nRows = %d nCols = %d WARN dhcpcEnable: unable to kill dhclient ERROR pppoeMgmtDBUpdateHandler: empty update. WARN dhcpcEnable: enabling dhcpc failed on: %s ERROR dhcpcEnable: dhclient already running on: %s WARN dhcpcDisable: unable to kill dhclient ERROR dhcpcDisable: deleted dhclient.leases WARN dhcpcDisable: delete failed for dhclient.leases ERROR l2tpMgmtInit: unable to open the database file %s ERROR dhcpcDisable: failed to reset the ip ERROR l2tpEnable: unable to resolve address: %s ERROR dhcpcMgmtTblHandler: unable to get current Mtu Option ERROR l2tpEnable: inet_aton failed ERROR dhcpcMgmtTblHandler: unable to get the Mtu ERROR
Unified Services Router User Manual 153 The Enable Command is %s ERROR dhcpcMgmtTblHandler: dhclient enable failed ERROR l2tpEnable:Executing the Command failed ERROR dhcpcMgmtTblHandler: dhcpc release failed ERROR l2tpDisable: command string: %s ERROR dhcpcMgmtTblHandler: dhcpc disable failed ERROR l2tpDisable: unable to stop l2tp session ERROR dhcpcMgmtDBUpdateHandler: failed query: %s ERROR l2tpMgmtTblHandler: unable to get current MTU option ERROR dhcpcMgmtDBUpdateHandler: error in executing " ERROR l2tpMgmtTblHandler: unable to get the Mtu ERROR DHCPv6 Client start failed. ERROR l2tpMgmtTblHandler: dbRecordValueGet failed for %s " ERROR DHCPv6 Client stop failed. ERROR l2tpMgmtTblHandler: l2tpEnable failed ERROR failed to create/open DHCPv6 client " ERROR l2tpMgmtTblHandler: disabling l2tp failed ERROR failed to write DHCPv6 client configuration file ERROR l2tpMgmtDBUpdateHandler: sqlite3QueryResGet " ERROR failed to restart DHCPv6 Client ERROR l2tpMgmtDBUpdateHandler: error in executing ERROR failed to create/open DHCPv6 Server " ERROR Illegal invocation of tcpdumpConfig (%s) ERROR Restoring old configuration.. ERROR Failed to start tcpdump ERROR DHCPv6 Server configuration update failed ERROR Failed to stop tcpdump ERROR DHCPv6 Server Restart failed ERROR Invalid tcpdumpEnable value ERROR sqlite3QueryResGet failed.Query:%s ERROR Facility: System (VPN) Log Message Severity Log Message Severity %d command not supported by eapAuth DEBUG PEAP key derive: ERROR ERROR pCtx NULL. DEBUG PEAP context is NULL: ERROR ERROR Current cert subject name= %s DEBUG Constructing P2 response: ERROR ERROR X509_STORE_CTX_get_ex_data failed. DEBUG innerEapRecv is NULL: ERROR ERROR Cannot get cipher, no session est. DEBUG Decrypting TLS data: ERROR ERROR %s: SSL_ERROR_WANT_X509_LOOKUP DEBUG Wrong identity size: ERROR ERROR err code = (%d) in %s DEBUG Wrong size for extensions packet: ERROR ERROR BIO_write: Error DEBUG innerEapRecv is NULL: ERROR. ERROR Decrypting: BIO reset failed DEBUG Inner EAP processing: ERROR ERROR Encrypting BIO reset: ERROR DEBUG TLS handshake: ERROR. ERROR BIO_read: Error DEBUG Sending P1 response: ERROR ERROR EAP state machine changed from %s to %s. DEBUG Unexpected tlsGlueContinue return value. ERROR EAP state machine changed from %s to %s. DEBUG No more fragments in message. ERROR ERROR Received EAP Packet with code %d DEBUG No phase 2 data or phase 2 data buffer NULL: ERROR ERROR Response ID %d DEBUG Allocating memory for PEAP Phase 2 payload: ERROR ERROR Response Method %d DEBUG TLS encrypting response: ERROR ERROR
Unified Services Router User Manual 154 Created EAP/PEAP context: OK DEBUG Setting message in fragment buffer: ERROR ERROR Deleted EAP/PEAP context: OK DEBUG Allocating TLS read buffer is NULL: ERROR ERROR Upper EAP sent us: decision = %d method state = %d DEBUG Setting last fragment: ERROR ERROR P2 decision=(%d); methodState=(%d) DEBUG Getting message: ERROR ERROR Writing message to BIO: ERROR. DEBUG Processing PEAP message: ERROR ERROR Encrypted (%d) bytes for P2 DEBUG Setting fragment: ERROR ERROR P2: sending fragment. DEBUG Creating receive buffer: ERROR ERROR P2: message size = %d DEBUG Setting first fragment: ERROR ERROR P2: sending unfragmented message. DEBUG Sending P1 response: ERROR ERROR P1: Sending fragment. DEBUG NULL request (or response) PDU or NULL context: ERROR ERROR P1: Total TLS message size = (%d) DEBUG Expecting start packet, got something else: ERROR ERROR P1: sending unfragmented message. DEBUG Protocol version mismatch: ERROR ERROR peapFragFirstProcess: TLS record size to receive = (%d) DEBUG Processing PEAP message (from frag): ERROR ERROR Setting version %d DEBUG Processing PEAP message: ERROR ERROR PEAP pkt rcvd: data len=(%d) flags=(%d) version=(%d) DEBUG Processing PEAP message: ERROR ERROR Got PEAP/Start packet. DEBUG Indicated length not valid: ERROR ERROR Got first fragment DEBUG Did not get Acknowledged result: ERROR ERROR Got fragment (n) DEBUG Cannot understand AVP value: ERROR ERROR Got last fragment DEBUG eapExtResp is NULL: ERROR ERROR Got unfragmented message DEBUG eapWscCtxCreate: EAPAUTH_MALLOC failed. ERROR Got frag ack. DEBUG eapWscProcess: umiIoctl req to WSC failed, status = %d ERROR Ext AVP parsed: flags=(0x%x) DEBUG eapWscCheck: Invalid frame ERROR Mandatory bit not set: WARNING DEBUG eapWscBuildReq: Invalid state %d ERROR Ext AVP parsed: type=(%d) DEBUG eapWscProcessWscResp: Invalid data recd pData = %p, dataLen" ERROR Ext AVP parsed: value=(%d) DEBUG Data received for invalid context, dropping it ERROR Got PEAPv0 success! DEBUG eapWscProcessWscResp: Build Request failed ERROR Got PEAPv0 failure! DEBUG eapWscProcessWscResp: Invalid state %d ERROR pCtx NULL. DEBUG eapWscProcessWscResp: Message processing failed 0x%X ERROR Authenticator response check: Error DEBUG eapWscProcessWscData: Invalid notification recd %d ERROR Authenticator response check: Failed DEBUG unable to initialize MD5 ERROR MS-CHAP2 Response AVP size = %u DEBUG MDString: adpDigestInit for md5 failed ERROR Created EAP/MS-CHAP2 context: OK. DEBUG EAPAUTH_MALLOC failed. ERROR pCtx NULL. DEBUG EAPAUTH_MALLOC failed. ERROR Deleted EAP/MS-CHAPv2 context: OK DEBUG NULL context created: Error ERROR Not authenticated yet. DEBUG NULL context received: Error ERROR Authenticator response invalid DEBUG Authenticator ident invalid. ERROR EAP-MS-CHAPv2 password changed. DEBUG Success request message invalid: ERROR
Unified Services Router User Manual 155 Error rcvd. opCode %d. DEBUG Plugin context is NULL ERROR pCtx NULL. DEBUG Deriving implicit challenge: Error ERROR TLS message len changed in the fragment, ignoring. DEBUG Generating NT response: Error ERROR no data to send while fragment ack received. DEBUG NULL in/out buffer: Error ERROR TLS handshake successful. DEBUG Incorrect vendor id. ERROR Created EAP/TTLS context: OK DEBUG Allocating memory for outBuff: ERROR ERROR Deleted EAP/TTLS context: OK DEBUG AVP code not recognized ERROR No more fragments in message. ERROR DEBUG EAPAUTH_MALLOC failed. ERROR Upper EAP sent us: method state = %d; decision = %d DEBUG Converting password to unicode: Error ERROR P2: sending fragment. DEBUG Generating password hash: Error. ERROR P2 send unfragmented message. DEBUG Generating password hash hash: Error. ERROR P1: sending fragment. DEBUG Generating master key: Error. ERROR P1: sending unfragmented message. DEBUG Generating first 16 bytes of session key: Error.n ERROR \tTLSMsgLen = 0x%x DEBUG Generating second 16 bytes of session key: Error.n ERROR Send req ptr = 0x%x; Send resp ptr = 0x%x DEBUG Converting password to unicode: Error ERROR P2 decision=(%d); methodState=(%d) DEBUG Constructing failure response: ERROR ERROR Default EAP: method state = %d; decision = %d DEBUG Error checking authenticator response. ERROR TTLS pkt: data len=(%d) flags=(0x%x) DEBUG Error generating NT response. ERROR Got start DEBUG Username string more than 256 ASCII characters: ERROR ERROR Got first fragment (n). DEBUG Invalid Value-Size. ERROR Got fragment (n). DEBUG Invalid MS-Length. Got (%d), expected (%d) ERROR Got last fragment DEBUG Error constructing response. ERROR Got unfragmented message. DEBUG Got type (%d), expecting (%d) ERROR Got frag ack. DEBUG Cannot handle message; opCode = %d ERROR Rcvd. AVP Code-%u: flags-0x%x: len-%u: vendorId-%u: " DEBUG EAPAUTH_MALLOC failed. ERROR MOD EAP: method state from upper = %d; decision = %d DEBUG tlsGlueCtxCreate failed. ERROR Got AVP len = %ul. Should be less than 16777215 DEBUG client certificate must be set in the profile. ERROR AVP length extract: Error DEBUG received tls message length too big. ERROR pFB is NULL DEBUG total frags len > initial total tls length. ERROR Requesting message before assembly complete DEBUG total frags len > initial total tls length. ERROR pFB is NULL DEBUG total data rcvd(%d) doesnt match the initial " ERROR pFB is NULL DEBUG couldnt write %d data to TLS buffer. ERROR Buffer cannot hold message: ERROR DEBUG invalid flags %s passed to eapTlsBuildResp. ERROR pFB is NULL: Error DEBUG EAPAUTH_MALLOC failed. ERROR pFB is NULL DEBUG tlsGlueCtxCreate failed. ERROR TLS_FB* is NULL. DEBUG Context NULL: ERROR ERROR
Unified Services Router User Manual 156 pFB->msgBuff is NULL. DEBUG Setting profile to glue layer: ERROR. ERROR Error calculating binary. DEBUG _eapCtxCreate failed. ERROR Error calculating binary. DEBUG %d authentication not enabled in the system. ERROR adpDigestInit for SHA1 failed. DEBUG Initializing inner non-EAP auth plugin: ERROR ERROR adpDigestInit for SHA1 failed. DEBUG TTLS key derive: ERROR ERROR E = %d DEBUG TTLS context from EAP plugin is NULL: ERROR ERROR R = %d DEBUG Allocating memory for TTLS Phase 2 payload: ERROR ERROR Could not initialize des-ecb DEBUG TLS Encrypting response: ERROR ERROR adpDigestInit for MD4 failed. DEBUG Allocating TLS read buffer is NULL: ERROR ERROR adpDigestInit for SHA1 failed. DEBUG Inner authentication (id: %d) unhandled ERROR adpDigestInit for SHA1 failed. DEBUG innerEapRecv is NULL: ERROR. ERROR Error converting received auth reponse to bin. DEBUG Decrypting TLS data: ERROR ERROR Gnerating challenge hash: Error DEBUG Processing Phase 2 method: Error ERROR Generating password hash: Error DEBUG Writing message to BIO: ERROR. ERROR Generating challenge response: Error DEBUG TLS handshake: ERROR. ERROR Conn cipher name=%s ver=%s: %s DEBUG Unexpected tlsGlueContinue return value. ERROR Send req ptr = 0x%x; Send resp ptr = 0x%x DEBUG NULL request (or response) PDU or NULL context ERROR Request ptr = 0x%x; DEBUG Protocol version mismatch: ERROR ERROR Response ptr = 0x%x DEBUG Creating receive buffer: ERROR ERROR Rcvd. AVP Code - %ul DEBUG Setting first fragment: ERROR ERROR Rcvd. AVP flags - 0x%02x DEBUG Setting fragment: ERROR ERROR Rcvd. AVP len - %ul DEBUG Setting last fragment: ERROR ERROR Rcvd. AVP vendor id - %ul DEBUG Getting message: ERROR ERROR \tCode = %d DEBUG Processing TTLS message: ERROR ERROR \tIdent = %d DEBUG Processing TTLS message: ERROR ERROR \tLen = %d DEBUG Processing TTLS message: ERROR ERROR \tType = %d DEBUG Decapsulating AVP: ERROR ERROR \tOpCode = %d DEBUG Processing EAP receive: Error ERROR \tMSID = %d DEBUG AVP code not EAP: Error ERROR \tmsLen = %d DEBUG Encapsulating AVP: ERROR ERROR \tvalSize = %d DEBUG profile %s doesnt exist. ERROR Frag Buffer bytes left = (%d) DEBUG profile %s is in use. ERROR Stripped username=(%s) DEBUG profile %s already exists. ERROR digestLen = %d. DEBUG EAPAUTH_MALLOC failed ERROR ClearText = DEBUG User not found. ERROR CipherText = DEBUG EAP-MD5 not enabled in system configuration. ERROR digestLen = %d. DEBUG EAP-MSCHAPV2 not enabled in system configuration. ERROR digestLen1 = %d. DEBUG EAP-TLS not enabled in system configuration. ERROR digestLen2 = %d. DEBUG EAP-TTLS not enabled in system configuration. ERROR
Unified Services Router User Manual 157 password change is not allowed for this user DEBUG EAP-PEAP not enabled in system configuration. ERROR completed writing the policy DEBUG EAP-WSC not enabled in system configuration. ERROR completed writing the SA DEBUG PAP not enabled in system configuration. ERROR completed writing the proposal block DEBUG CHAP not enabled in system configuration. ERROR cmdBuf: %s DEBUG MSCHAP not enabled in system configuration. ERROR X509_DEBUG : Invalid Certificate for the generated" DEBUG MSCHAPV2 not enabled in system configuration. ERROR X590_ERROR : Failed to create File '%s' DEBUG PAP/Token not enabled in system configuration. ERROR x509TblHandler DEBUG EAP-MD5 not enabled in system configuration. ERROR pCertType: %s DEBUG EAP-MSCHAPV2 not enabled in system config. ERROR pRowQueryStr: %s DEBUG EAP-TLS not enabled in system configuration. ERROR x509SelfCertTblHandler DEBUG EAP-TTLS and EAP-PEAP are not valid as inner" ERROR pRowQueryStr: %s DEBUG invalid innerAuth %d. ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG profile %s doesnt exist. ERROR umiRegister failed ERROR Re-assembling fragments incorrect size ERROR eapAuthHandler: Invalid data received ERROR Error creating cipher context. ERROR EAPAUTH_MALLOC failed. ERROR Error initializing cipher context. ERROR malloc failed. ERROR Error creating digest context. ERROR BIO_new_mem_buf failed. ERROR Error initializing digest context. ERROR malloc failed. ERROR Error initializing DES in Klite ERROR BIO_new_mem_buf failed. ERROR Error initializing MD4 in Klite ERROR SSL_CTX_new (TLSv1_client_method) failed. ERROR Error initializing RC4 in Klite ERROR unable to set user configured CIPHER list %s ERROR Error initializing SHA in Klite ERROR Certificate verification failed. ERROR Error cleaning cipher context. ERROR Server name match failed. Got (%s) expected " ERROR Error destroying cipher context. ERROR SSL_CTX_use_certificate_file (cert, PEM) failed. ERROR Error cleaning digest context. ERROR SSL_CTX_use_PrivateKey_file failed. ERROR Error destroying digest context. ERROR private key does not match public key ERROR Error stripping domain name. ERROR SSL_CTX_load_verify_locations failed ERROR Error cleaning digest context. ERROR SSL_new failed. ERROR Error cleaning digest context. ERROR Both SSL_VERIFY_PEER and SSL_VERIFY_NONE set: Error ERROR Challenge not present in failure packet. ERROR EAPAUTH_MALLOC failed. ERROR Wrong challenge length. ERROR EAPAUTH_MALLOC failed. ERROR Incorrect password change version value. ERROR eapTimerCreate failed. ERROR Error generating password hash. ERROR eapCtxDelete:pCtx == NULL ERROR Error generating password hash. ERROR eapRole != EAP_ROLE_PEER or EAP_ROLE_AUTHENTICATOR ERROR Error encrypting password hash with block ERROR
Unified Services Router User Manual 158 pEapCtx == NULL or pPDU == NULL. ERROR Could not initialize des-ecb ERROR received EAP pdu bigger than EAP_MTU_SIZE. ERROR Error cleaning cipher context. ERROR received EAP pdu bigger than EAP_MTU_SIZE. ERROR Error cleaning cipher context. ERROR state machine is in invalid state. ERROR Error cleaning digest context. ERROR unable to create method context. ERROR Error cleaning digest context. ERROR method ctxCreate failed. ERROR adpDigestInit for SHA1 failed. ERROR method profile set failed. ERROR X509_ERROR : .Query:%s ERROR state machine is in invalid state. ERROR X509_ERROR : Invalid Certificate for the " ERROR Only StandAlone authenticator supported currently. ERROR invalid x509 certificate ERROR state machine is in invalid state. ERROR Couldn't get the x509 cert hash ERROR BuildReq operation failed ERROR Memory allocation failed ERROR No method ops defined for current method ERROR FileName too lengthy ERROR Process operation failed ERROR Couldn't execute command ERROR state machine is in invalid state. ERROR Memory allocation failed ERROR Packet length mismatch %d, %d ERROR Memory allocation failed ERROR eapAuthTypeToType: Invalid eapAuthType %d ERROR invalid certificate data ERROR eapTypeToAuthType: Invalid eapType %d ERROR .Query:%s ERROR unable to create method context. ERROR .Query:%s ERROR method ctxCreate failed. ERROR Memory allocation failed ERROR Invalid condition, methodState = %d, respMethod = %d ERROR X509_ERROR : Failed to validate the certficate " ERROR A EAP Ctx map already exists ERROR Memory allocation failed ERROR eapTimerCreate: Currently unsupported for Peer role ERROR .Query:%s ERROR eapTimerStart: Currently unsupported for Peer role ERROR Invalid Sign Key Length : %d ERROR eapTimerDestroy: Currently unsupported for Peer role ERROR Invalid Hash Alg : %d ERROR eapTimerCancel: Currently unsupported for Peer role ERROR Invalid Sign Alg : %d ERROR eapTimerHandler: Currently unsupported for Peer role ERROR No Memory Available ERROR pCtx is NULL: ERROR ERROR Certificate Request Failed ERROR tlsGlueCtxCreate failed ERROR File Open Failed ERROR eapVars is NULL ERROR File is Empty ERROR Context NULL: ERROR ERROR Memory Allocation Failed ERROR Initializing inner EAP auth: ERROR ERROR File Open Failed ERROR pCtx is NULL: ERROR ERROR File is Empty ERROR Memory Allocation Failed ERROR Error in executing DB update handler ERROR Facility: System (Admin) Log Message Severity Log Message Severity Usage:%s <DBFile> DEBUG unable to register to UMI ERROR
Unified Services Router User Manual 159 Could not open database: %s DEBUG sqlite3QueryResGet failed ERROR CPU LOG File not found DEBUG radSendtoServer: socket: %s ERROR MEM LOG File not found DEBUG radSendtoServer: bind() Failed: %s: %s ERROR cpuMemUsageDBUpdateHandler: update query: %s DEBUG radRecvfromServer: recvfrom() Failed: %s ERROR Printing the whole list after inserting DEBUG radRecvfromServer: Packet too small from %s:%d: %s ERROR %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG radCheckMsgAuth: Invalid Message-Authenticator length in" ERROR adpCmdExec exited with return code=%d DEBUG radDictLoad: couldn't open dictionary %s: %s ERROR %s op=%d row=%d DEBUG radBuildAndSendReq: Invalid Request Code %d ERROR sqlite3_mprintf failed DEBUG radPairAssign: bad attribute value length ERROR sqlite3QueryResGet failed: query=%s DEBUG radPairAssign: unknown attribute type %d ERROR Printing the whole list after delete DEBUG radPairNew: unknown attribute %d ERROR %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG radPairGen: Attribute(%d) has invalid length ERROR Printing the whole list after inserting DEBUG radPairValue: unknown attribute type %d ERROR %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG radPairValueLen: unknown attribute type %d ERROR email logs: No logging events enabled DEBUG radPairLocate: Attribute(%d) has invalid length ERROR %s DEBUG radPairUnpackDefault: Unknown-Attribute[%d]: ERROR Mail sent and the Database is reset. DEBUG radConfigure: can't open %s: %s ERROR Disabled syslog server DEBUG radConfigure: %s: line %d: bogus format: %s ERROR Event logs are full, sending logs to email DEBUG radConfAssert: No AuthServer Specified ERROR Email logs sending failed DEBUG radConfAssert: No Default Timeout Specified ERROR Packing attribute: %s DEBUG radConfAssert: No Default Retry Count Specified ERROR Server found: %s, secret: %s DEBUG radExtractMppeKey: Invalid MS-MPPE-Key Length ERROR Packed Auth. Reqest: code:%d, id:%d, len:%d DEBUG radVendorMessage: Invalid Length in Vendor Message ERROR Sending Packet to %x:%d .... DEBUG radVendorMessage: Unknown Vendor ID received:%d ERROR Receiving Reply Packet.... DEBUG radVendorAttrGet: Invalid Length in Vendor Message ERROR Verified Reply Packet Integrity DEBUG radVendorAttrGet: Unknown Vendor ID:%d ERROR Generated Reply Attribute-Value pairs DEBUG radVendorMessagePack: Unknown Vendor ID:%d ERROR Verified Message-Authenticator DEBUG radGetIPByName: couldn't resolve hostname: %s ERROR Unloaded RADIUS Dictionary DEBUG radGetHostIP: couldn't get hostname ERROR Adding Dictionary Attribute %s DEBUG radGetHostIP: couldn't get host IP address ERROR Adding Dictionary Value %s DEBUG radius dictionary loading failed ERROR Loaded Dictionary %s DEBUG Failed to set default timeout value ERROR
Unified Services Router User Manual 160 Adding Dictionary Attribute '%s' DEBUG Failed to set default retries value ERROR Adding Dictionary Value %s DEBUG ERROR: incomplete DB update information. ERROR Receiving attribute: %s DEBUG old values result does not contain 2 rows ERROR Processing attribute: %s DEBUG sqlite3QueryResGet failed ERROR Processing attribute: %s DEBUG empty update. nRows=%d nCols=%d ERROR Processing attribute: %s DEBUG Error in executing DB update handler ERROR Processing attribute: %s DEBUG sqlite3QueryResGet failed ERROR radConfGet: " DEBUG Invalid SQLITE operation code - %d ERROR Added Server %s:%d with " DEBUG sqlite3QueryResGet failed ERROR Added Server %s:%d with " DEBUG empty result. nRows=%d nCols=%d ERROR Default Timeout Set to %d DEBUG sqlite3QueryResGet failed ERROR Default Retry Count Set to %d DEBUG empty result. nRows=%d nCols=%d ERROR %s - %s : %d DEBUG RADIUS Accounting Exchange Failed ERROR Deleting Server %s:%d with " DEBUG Unable to set debug for radAcct. ERROR Adding RowId:%d to Server %s:%d with " DEBUG Unable to set debug level for radAcct. ERROR rowIds: %d - %d DEBUG ERROR: option value not specified ERROR Deleting Server %s:%d with " DEBUG ERROR: option value not specified ERROR RADIUS Deconfigured DEBUG Unable to initialize radius ERROR Found Option %s on line %d of file %s DEBUG radEapMsgQueueAdd: Invalid EAP packet length(%d) ERROR Setting Option %s with value %s DEBUG radEapRecvTask: invalid EAP code:%d ERROR RADIUS Configured DEBUG radEapRecvTask: Packet length mismatch %d, %d ERROR %d : Server %s:%d with " DEBUG No attributes received in Access-Challenge message ERROR DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG No State Attribute in Access-Challenge message ERROR Host IP address: %s DEBUG radEapRecvTask: " ERROR Adding Packet for existing cookie:%p DEBUG failed to initialize UMI ERROR Adding Packet and cookie:%p DEBUG umiRegister failed. errno=%d ERROR Releasing Packet and cookie:%p DEBUG Invalid arguments to ioctl handler ERROR Releasing Packet with cookie:%p DEBUG radEapSendRtn: Invalid Arguments ERROR Received EAP-Identity from Pnac: %s DEBUG radEapSendRtn: failed to allocate buffer ERROR Filling User-Name: %s DEBUG umiIoctl failed ERROR Filling State: DEBUG failed to initialize EAP message queue ERROR Filling EAP-Message: DEBUG Unable to set debug for radEap. ERROR Filling Service-Type: %d DEBUG Unable to set debug level for radEap. ERROR Filling Framed-MTU: %d DEBUG ERROR: option value not specified ERROR Received Access-Challenge from Server DEBUG ERROR: option value not specified ERROR Sending Reply EAP Packet to Pnac DEBUG could not initialize MGMT framework ERROR Error sending packet to Pnac DEBUG Unable to initialize radius ERROR RADIUS Authentication Failed; " DEBUG Unable to set debug for radEap. ERROR RADIUS Authentication Successful; " DEBUG Unable to set debug level for radEap. ERROR Got Packet with cookie:%p DEBUG ERROR: option value not specified ERROR Next DNS Retry after 1 min DEBUG Unable to initialize radius ERROR Next Synchronization after" DEBUG Invalid username or password ERROR
Unified Services Router User Manual 161 Next Synchronization after" DEBUG Unable to set debug for radAuth. ERROR Next Synchronization after %d \ DEBUG Unable to set debug level for radAuth. ERROR Primary is not available, " DEBUG ERROR: option value not specified ERROR Secondary is not available, " DEBUG Unable to initialize radius ERROR Invalid value for use default servers, " DEBUG Invalid username, challenge or response ERROR No server is configured, " DEBUG Unable to set debug for radAuth. ERROR Backing off for %d seconds DEBUG Unable to set debug level for radAuth. ERROR Requesting time from %s DEBUG ERROR: option value not specified ERROR Synchronized time with %s DEBUG Unable to initialize radius ERROR Received KOD packet from %s DEBUG Invalid username or password ERROR No suitable server found %s DEBUG usage : %s <DB fileName> ERROR Received Invalid Length packet from %s DEBUG ntpd : umi initialization failed ERROR Received Invalid Version packet from %s DEBUG ntpd : ntpInit failed ERROR Received Invalid Mode packet from %s DEBUG ntpd : ntpMgmtInit failed ERROR Request Timed out from %s DEBUG There was an error while getting the timeZoneChangeScript." ERROR Looking Up %s DEBUG unexpected reply from %d cmd=%d ! ERROR Timezone difference :%d DEBUG cmd %d not supported. caller %d ERROR Could not open file: %s DEBUG default reached ERROR Could not read data from file DEBUG Unable to initialize ntpControl ERROR ntpTblHandler DEBUG ntpMgmt : Couldn't open database %s ERROR status: %d DEBUG ERROR : incomplete DB update information ERROR tz: %d DEBUG empty update. nRows=%d nCols=%d ERROR DayLightsaving: %d DEBUG Error in executing DB update handler ERROR pNtpControl->ServerNames[PRIMARY_SERVER]: %s DEBUG requestNtpTime: Invalid addr ERROR pNtpControl->ServerNames[SECONDARY_SERVER]: %s DEBUG failed to take lock for compId: %d ERROR DS: %d DEBUG failed to convert ioctl args to buffer for" ERROR pPriServ %s DEBUG request timeout dst(%d) <-- src(%d) ERROR pSecServ %s DEBUG failed to take lock for compId: %d ERROR Making request from %d --> %d DEBUG umiIoctlArgsToBuf: failed to allocate memory ERROR sent request dst(%d) <-- src(%d) using option %d DEBUG umiRecvFrom: could not allocate memory ERROR received request too small!(%d bytes) DEBUG adpMalloc failed ERROR Received a UMI request from %d DEBUG context with ID: %d already registered ERROR sent a reply src(%d) ---> dst(%d) DEBUG Failed to allocate memory for creating UMI context ERROR umiRegister (%x,%x,%x,%x) DEBUG Failed to create recvSem for UMI context ERROR srcId=%d(%s) --> destId=%d(%s) cmd=%d inLen=%d outLen=%d DEBUG Failed to create mutex locks for UMI context ERROR waiting for reply...Giving Up DEBUG Failed to create mutex recvQLock for UMI context ERROR No request in the list after semTake DEBUG Invalid arguments to umiIoctl ERROR reply timeout DEBUG could not find the destination context ERROR
Unified Services Router User Manual 162 timeout after semTake DEBUG memPartAlloc for %d size failed ERROR srcId=%d(%s) <-- destId=%d(%s) cmd=%d DEBUG memPartAlloc for %d size failed ERROR Un-registerting component with Id %d DEBUG No Handler registered for this UMI context ERROR failed to send ioctl request: dst(%d) <--- src(%d) DEBUG Couldn't find component with ID (%d)," ERROR processed a reply dst(%d) <-- src(%d) DEBUG id=%d handler=%x ERROR request with no result option dst(%d) <-- src(%d) DEBUG Received NULL buffer in umiBufToIoctlArgs() ERROR cmd = %s DEBUG usbMgmtInit: unable to open the database file %s ERROR cmdstring is %s %s:%d DEBUG call to printConfig failed ERROR Calling printerConfig binary ... DEBUG Failed to Disable Network Storage" ERROR Calling unmount for USB ... DEBUG Some error occurred while removing device ERROR Calling mount for USB ... DEBUG Some error occurred while removing device ERROR usbdevice is %d %s:%d DEBUG Sqlite update failed ERROR Query string: %s DEBUG Failed to enable printer properly ERROR sqlite3QueryResGet failed.Query:%s DEBUG Failed to mount device on system ERROR %s: 1. usb is already disconnected for old usb type. " DEBUG Failed to enable network storage device" ERROR %s: 2.call disable for new usb type ! DEBUG Failed to mount device on system ERROR %s: 3. usb is already disconnected for old usb type. " DEBUG Sqlite update failed ERROR %s: 4. Disabled old usb type . Now " DEBUG USB1 Touch failed ERROR usbdevice is %d %s:%d DEBUG USB2 Touch failed ERROR USB: failed to begin transaction: %s DEBUG Sqlite update failed ERROR USB: SQL error: %s pSetString = %s DEBUG Failed query: %s ERROR USB: failed to commit transaction: %s DEBUG Failed to execute usb database update handler ERROR USB: updated table: %s DEBUG Usage:%s <DBFile> <opType> <tblName> <rowId> ERROR USB: returning with status: %s DEBUG Illegal invocation of snmpConfig (%s) ERROR %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG Invalid Community Access Type ERROR executing %s status =%d DEBUG Invalid User Access Type ERROR executing %s DEBUG Invalid Security Level ERROR %s returned status=%d DEBUG Invalid Authentication Algorithm ERROR %s returned status=%d DEBUG Invalid Privacy Algorithm ERROR snmpd.conf not found DEBUG Invalid Argument ERROR [SNMP_DEBUG] : Fwrite Successful DEBUG Failed to allocate memory for engineID ERROR [SNMP_DEBUG] : Fwrite failed DEBUG [SNMP_DEBUG]: Failed to get host address ERROR radPairGen: received unknown attribute %d of length %d WARN [SNMP_DEBUG] : FOPEN failed ERROR radPairGen: %s has unknown type WARN sqlite3QueryResGet failed.Query:%s ERROR radPairLocate: unknown attribute %ld of length %d WARN sqlite3QueryResGet failed.Query:%s ERROR radPairLocate: %s has unknown type WARN Invalid Security Level ERROR Illegal invocation of cpuMemUsage (%s) ERROR Invalid Authentication Algorithm ERROR
Unified Services Router User Manual 163 cpuMemUsageDBUpdateHandler: SQL error: %s ERROR Invalid Privacy Algorithm ERROR unable to open the DB file %s ERROR Failed to Get Host Address ERROR umiInit failed ERROR Invalid version ERROR unable to register to UMI ERROR snmp v3 Trap Configuration Failed ERROR Error Reading from the Database. ERROR sqlite3QueryResGet failed query:%s ERROR short DB update event request! ERROR sqlite3QueryResGet failed.Query:%s ERROR Error in executing DB update handler ERROR Failed to Open Snmp Configuration File ERROR adpListNodeRemove : Returned with an error ERROR Failed to write access control entries ERROR command too long. Try increasing " ERROR Failed to write snmpv3 users entries ERROR failed to allocate memory for CRON_NODE ERROR Failed to write snmp trap entries ERROR sqlite3QueryResGet failed ERROR Failed to write system entries. ERROR There was an error while reading the schedules. ERROR Failed to restart snmp ERROR unable to register to UMI ERROR %s failed with status ERROR short DB update event request! ERROR Error in executing DB update handler ERROR malloc(DB_UPDATE_NODE) failed ERROR %s: Unable to open file: %s ERROR short ifDev event request! ERROR RADVD start failed ERROR sqlite3_mprintf failed ERROR RADVD stop failed ERROR no component id matching %s ERROR failed to create/open RADVD configuration file %s ERROR umiIoctl (%s, UMI_CMD_DB_UPDATE(%d)) failed. ERROR Restoring old configuration.. ERROR sqlite3_mprintf failed ERROR failed to write/update RADVD configuration file ERROR sqlite3_mprintf failed ERROR upnpDisableFunc failed ERROR no component id matching %s ERROR upnpEnableFunc failed ERROR umiIoctl (%s, UMI_CMD_IFDEV_EVENT(%d)) failed. ERROR sqlite3QueryResGet failed.Query:%s ERROR klogctl(9) failed ERROR Error in executing DB update handler ERROR malloc failed for %d bytes ERROR unable to open the DB file %s ERROR klogctl(4) failed ERROR umiInit failed ERROR emailLogs: Invalid Number of Arguments!! Exiting. ERROR unable to register to UMI ERROR sqlite3QueryResGet failed ERROR short DB update event request! ERROR Could not execute the smtpClient. ERROR short ifDev event request! ERROR Error while cleaning the database.Exiting. %s ERROR sqlite3_mprintf failed ERROR %s failed. status=%d ERROR Facility: System (Firewall) Log Message Severity Log Message Severity Enabling rule for protocol binding. DEBUG Disable all NAT rules. DEBUG Disabling rule for protocol binding. DEBUG Enable all NAT rules. DEBUG Enabling Remote SNMP on WAN. DEBUG Enabling NAT URL filter rules. DEBUG Disabling Remote SNMP on WAN DEBUG Restarting all NAT rules. DEBUG
Unified Services Router User Manual 164 wan traffic counters are restared DEBUG Deleting schedule based firewall rules. DEBUG Traffic limit has been reached DEBUG Deleting schedule based firewall rules from DB. DEBUG Traffic meter monthly limit has been changed to %d. DEBUG Update schedule based firewall rules in DB. DEBUG Enabling traffic meter for only dowload. DEBUG Restart schedule based firewall rules. DEBUG Enabling traffic meter for both directions. DEBUG inter vlan routing enabled DEBUG Enabling traffic meter with no limit. DEBUG inter vlan routing disabled DEBUG Email alert in traffic meter disabled. DEBUG Disabling Content Filter for %d DEBUG Email alert in traffic meter enabled. DEBUG Enabling Content Filter for %d DEBUG Traffic Meter:Monthly limit %d MB has been " DEBUG ./src/firewall/linux/user/firewalld.c:59:#undef ADP_DEBUG2 DEBUG Traffic Metering: Adding rule to drop all traffic DEBUG ./src/firewall/linux/user/firewalld.c:61:#define ADP_DEBUG2 printf DEBUG Traffic Metering: %sabling Email traffic DEBUG Enabling Source MAC Filtering DEBUG Disabling attack checks for IPv6 rules. DEBUG Disabling Source MAC Filtering DEBUG Enabling attack checks for IPv6 rules. DEBUG Adding MAC Filter Policy for Block & Permit Rest DEBUG Configuring one to one NAT settings with %s private start IP " DEBUG Adding MAC Filter Policy for Permit & Block Rest DEBUG Deleting forward one to one NAT having setting %s private start" DEBUG Restarting Source MAC Address Policy DEBUG Disabling attack check for Block ping to WAN interface. DEBUG Disabling Firewall Rule for DHCP Relay Protocol DEBUG Disabling attack check for Stealth mode for tcp DEBUG Enabling Firewall Rule for DHCP Relay Protocol DEBUG Disabling attack check for Stealth mode for udp DEBUG prerouting Firewall Rule add for Relay failed DEBUG Disabling attack check for TCP Flood. DEBUG prerouting Firewall Rule add for Relay failed DEBUG Disabling attack check for UDP Flood. DEBUG Deleting MAC Filter Policy for Address %s DEBUG Disabling attack check for IPSec. DEBUG Adding MAC Filter Policy for Address %s DEBUG Disabling attack check for PPTP. DEBUG Disabling Firewall Rules for DMZ host DEBUG Disabling attack check for L2TP. DEBUG Enabling Firewall Rules for DMZ host DEBUG Disabling attack check for UDP Flood. DEBUG Disabling Firewall Rules for Spill Over Load Balancing DEBUG Disabling attack check for IPSec. DEBUG Disabling Firewall Rules for Load Balancing DEBUG Disabling attack check for PPTP. DEBUG Enabling Firewall Rules for Load Balancing DEBUG Disabling attack check for L2TP. DEBUG Enabling Firewall Rules for Spill Over Load Balancing DEBUG Enabling attack check for Block ping to WAN " DEBUG Enabling Firewall Rules for Auto Failover DEBUG Enabling attack check for Stealth Mode for tcp. DEBUG Enabling Firewall Rules for Load Balancing . DEBUG Enabling attack check for Stealth Mode for udp. DEBUG Enabling Firewall Rules for Spill Over Load Balancing . DEBUG Enabling attack check for TCP Flood. DEBUG Enabling Firewall Rules for Auto Failover DEBUG Enabling attack check for UDP Flood. DEBUG Deleting BlockSites Keyword \ DEBUG Enabling attack check for IPSec. DEBUG Enabling BlockSites Keyword \ DEBUG Enabling attack check for PPTP. DEBUG Disabling BlockSites Keyword \ DEBUG
Unified Services Router User Manual 165 Enabling attack check for L2TP. DEBUG Updating BlockSites Keyword from \ DEBUG Enabling attack check for UDP Flood. DEBUG Inserting BlockSites Keyword \ DEBUG Enabling attack check for IPSec. DEBUG Deleting Trusted Domain \ DEBUG Enabling attack check for PPTP. DEBUG Adding Trusted Domain \ DEBUG Enabling attack check for L2TP. DEBUG Restarting Schedule Based Firewall Rules DEBUG Enabling DoS attack check with %d SyncFlood detect rate, " DEBUG Enabling Remote SNMP DEBUG Disabling DoS attack check having %d SyncFlood detect rate," DEBUG Disabling Remote SNMP DEBUG Enabling ICSA Notification Item for ICMP notification. DEBUG Enabling Remote SNMP DEBUG Enabling ICSA Notification Item for Fragmented Packets. DEBUG Disabling DOS Attacks DEBUG Enabling ICSA Notification Item for Multi cast Packets. DEBUG Enabling DOS Attacks DEBUG Disabling ICSA Notification Item for ICMP notification. DEBUG Enabling DOS Attacks DEBUG Disabling ICSA Notification Item for Fragmented Packets. DEBUG Restarting Firewall [%d]:[%d] For %s DEBUG Disabling ICSA Notification Item for Multi cast Packets. DEBUG restartStatus = %d for LogicalIfName = %s DEBUG Adding IP/MAC binding rule for %s MAC address " DEBUG Deleting Lan Group %s DEBUG Deleting IP/MAC binding rule for %s MAC " DEBUG Adding Lan Group %s DEBUG ./src/firewall/linux/user/firewalld.c:60:#undef ADP_DEBUG DEBUG Deleting lan host %s from group %s DEBUG ./src/firewall/linux/user/firewalld.c:62:#define ADP_DEBUG printf DEBUG Adding lan host %s from group %s DEBUG Restarting traffic meter with %d mins, %d hours, " DEBUG Disabling Firewall Rule for IGMP Protocol DEBUG Updating traffic meter with %d mins, %d hours, " DEBUG Enabling Firewall Rule for IGMP Protocol DEBUG Deleting traffic meter. DEBUG Deleting IP/MAC Bind Rule for MAC address %s and IP " DEBUG Disabling block traffic for traffic meter. DEBUG Adding IP/MAC Bind Rule for MAC address %s and IP DEBUG Enabling traffic meter. DEBUG Deleting Protocol Bind Rule for Service %s DEBUG Adding lan group %s. DEBUG Deleting Protocol Bind Rule for Service %s DEBUG Deleting lan group %s. DEBUG Deleting Protocol Bind Rule for Service %s DEBUG Renaming lan group from %s to %s. DEBUG Adding Protocol Bind Rule for Service %s DEBUG Deleting host %s from %s group. DEBUG %s Session Settings DEBUG Adding host %s to %s group. DEBUG Restarting IPv6 Firewall Rules... DEBUG Enabling Keyword blocking for %s keyword. DEBUG Deleting Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Disabling keyword Blocking for %s keyword . DEBUG Deleting Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Deleting trusted domain with keyword %s. DEBUG Enabling Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Adding %s keyword to trusted domain. DEBUG Disabling Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Enabling Management Access from DEBUG Enabling Port Trigger Rule for DEBUG
Unified Services Router User Manual 166 Internet on port %d %d:%d:%d:%d:%d Enabling remote access management for IP address range" DEBUG Disabling Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Enabling remote access management to only this PC. DEBUG Adding Port Trigger Rule for %d:%d:%d:%d:%d DEBUG Disabling Management Access from Internet on port %d DEBUG Enabling Content Filter DEBUG Disabling remote access management for IP address range" DEBUG Disabling Content Filter DEBUG Disabling remote access management only to this PC. DEBUG Enabling Content Filter DEBUG MAC Filtering %sabled for BLOCK and PERMIT REST. DEBUG Setting NAT mode for pLogicalIfName = %s DEBUG MAC Filtering %sabled for PERMIT and BLOCK REST. DEBUG Enabling DROP for INPUT DEBUG Enabling Content Filtering. DEBUG Enabling DROP for FORWARD DEBUG Disabling Content Filtering. DEBUG Enabling NAT based Firewall Rules DEBUG Deleting rule, port triggering for protocol TCP. DEBUG Setting transparent mode for pLogicalIfName \ DEBUG Deleting rule, port triggering for protocol UDP. DEBUG Enabling Accept for INPUT DEBUG Deleting rule, port triggering for protocol TCP. DEBUG Enabling Accept for FORWARD DEBUG Deleting rule, port triggering for protocol UDP. DEBUG Setting Routing mode for pLogicalIfName \ DEBUG Enabling rule, port triggering for protocol TCP. DEBUG Enabling DROP for INPUT DEBUG Enabling rule, port triggering for protocol UDP. DEBUG Enabling DROP for FORWARD DEBUG Enabling rule, port triggering for protocol TCP. DEBUG Disabling NAT based Firewall Rules DEBUG Enabling rule, port triggering for protocol UDP. DEBUG Enabling Firewall Rules for URL Filtering & " DEBUG Enabling DNS proxy. DEBUG Adding Firewall Rule for RIP Protocol DEBUG Restarting DNS proxy. DEBUG Restarting Schedule Based Firewall Rules DEBUG checking DNS proxy for Secure zone. DEBUG enabling IPS checks between %s and %s zones. DEBUG checking DNS proxy for Public zone. DEBUG disabling IPS checks between %s and %s zones. DEBUG Enabling Block traffic from %s zone. DEBUG Stopping IPS...%s DEBUG Configuring firewall session settings for " DEBUG IPS started. DEBUG Disabling DMZ DEBUG Route already exists DEBUG Disabling WAN-DMZ rules . DEBUG Route addition failed: Network Unreachable DEBUG Enabling WAN DMZ rules . DEBUG Route addition failed: Network is down DEBUG Restarting DMZ rule having %s address with %s address. DEBUG Route addition failed DEBUG Enabling LAN DHCP relay. DEBUG Failed to add rule in iptables DEBUG OneToOneNat configured successfully DEBUG Failed to delete rule from iptables DEBUG OneToOneNat configuration failed DEBUG fwLBSpillOverConfigure: Something going wrong here ERROR Deleting scheduled IPv6 rules. DEBUG fwLBSpillOverConfigure: unable to get interfaceName ERROR delete from FirewallRules6 where ScheduleName = '%s'. DEBUG fwLBSpillOverConfigure: Could not set PREROUTING rules ERROR
Unified Services Router User Manual 167 Update FirewallRules6 where ScheduleName = '%s' to New " DEBUG fwLBSpillOverConfigure: Could not set POSTROUTING rules ERROR Dns proxy Restart failed DEBUG fwLBSpillOverConfigure: Something going wrong Here ERROR deleting interface to ifgroup failed DEBUG fwL2TPGenericRules.c: unable to open the database file " ERROR adding interface to ifgroup failed DEBUG fwL2TPGenericRules.c: inet_aton failed ERROR deleting interface pVirtIface %s from ifgroup %d" DEBUG fwPPTPGenericRules.c: unable to open the database file " ERROR adding interface pVirtIface %s to ifgroup %d failed DEBUG fwPPTPGenericRules.c: inet_aton failed ERROR Deleting IP address %s. DEBUG DNS proxy firewall rule add failed for %s ERROR Adding new IP address %s. DEBUG deleting interface %s from ifgroup %d failed ERROR Updating old IP address %s to new IP address %s. DEBUG adding interface %s to ifgroup %d failed ERROR Restarting Firewall For %s Address Update from %s:%s DEBUG nimfBridgeTblHandler: unable to get interfaceName ERROR Disabling Firewall Rule for MSS packet marking DEBUG nimfBridgeTblHandler: \ ERROR Enabling Firewall Rule for MSS packet marking DEBUG nimfBridgeTblHandler: unable to get \ ERROR Enabling packet marking rule for %s IDLE timer DEBUG Failed to %s traffic from %s to %s to IPS. ERROR Deleted firewall rule %s for service %s with action %s DEBUG Failed to %s traffic from %s to %s to IPS. ERROR %s firewall rule %s for service %s with action %s DEBUG failed to start IPS service. ERROR Added firewall rule %s for service %s with action %s DEBUG Timeout in waiting for IPS service to start. ERROR Deleting inbound(WAN-LAN) firewall rule. DEBUG Usage:%s <DBFile> <opType> <tblName> <rowId> " ERROR Deleting inbound(WAN-DMZ) firewall rule. DEBUG xlr8NatConfig: illegal invocation of (%s) ERROR RIPng disabled. DEBUG Illegal invocation of [%s] ERROR RIPng enabled. DEBUG xlr8NatMgmtTblHandler: failed query: %s ERROR Disable IPv6 firewall rule. DEBUG Could not open file: %s ERROR Enable IPv6 firewall rule. DEBUG Rip Error Command Too Long ERROR Deleting IGMP proxy rule. DEBUG No authentication for Ripv1 ERROR Enable IGMP proxy rule. DEBUG Invalid Rip Direction ERROR Restarting IGMP rule. DEBUG Invalid Rip Version ERROR Traffic meter enabled with no limit type. DEBUG Invalid Password for 1st Key ERROR Traffic meter enabled for only download. DEBUG Invalid Time for 1st Key ERROR Traffic meter enabled for both directions. DEBUG Invalid Password for 2nd Key ERROR Deleted firewall rule %s for service %s with action %s DEBUG Invalid Time for 2nd Key ERROR %s firewall rule %s for service %s with action %s DEBUG Invalid First KeyId ERROR Added firewall rule %s for service %s with action %s DEBUG Invalid Second KeyId ERROR Enabling Inter VLAN routing. DEBUG Invalid Authentication Type ERROR Updating inter VLAN routing status. DEBUG ripDisable failed ERROR Deleting inter VLAN routing. DEBUG ripEnable failed ERROR
Unified Services Router User Manual 168 Facility: Local0 (Wireless) Log Message Severity Log Message Severity (node=%s) setting %s to val = %d DEBUG sqlite3QueryResGet failed ERROR Custom wireless event: '%s' DEBUG sqlite3QueryResGet failed ERROR Wireless event: cmd=0x%x len=%d DEBUG VAP(%s) set beacon interval failed ERROR New Rogue AP (%02x:%02x:%02x:%02x:%02x:%02x) detected DEBUG VAP(%s) set DTIM interval failed ERROR WPS session in progress, ignoring enrolle assoc request DEBUG VAP(%s) set RTS Threshold failed ERROR ran query %s DEBUG VAP(%s) set Fragmentation Threshold failed ERROR DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG VAP(%s) set Protection Mode failed ERROR %sing VAPs using profile %s DEBUG VAP(%s) set Tx Power failed ERROR %sing VAP %s DEBUG WDS Profile %s not found ERROR ran query %s DEBUG Failed to initalize WPS on %s ERROR %sing VAP instance %s DEBUG failed to get profile %s ERROR VAP(%s) set Short Preamble failed DEBUG could not initialize MGMT framework ERROR VAP(%s) set Short Retry failed DEBUG could not initialize MGMT framework ERROR VAP(%s) set Long Retry failed DEBUG dot11VapBssidUpdt SQL error: %s ERROR Decrypting context with key %s DEBUG sqlite3QueryResGet failed.Query:%s ERROR Unknown IAPP command %d received. DEBUG KDOT11_GET_PARAM(IEEE80211_IOC_CHANNEL) failed ERROR unexpected reply from %d cmd=%d ! DEBUG Failed to get the channel setting for %s ERROR unexpected reply from %d cmd=%d ! DEBUG sqlite3QueryResGet failed.Query:%s ERROR Recvied DOT11_EAPOL_KEYMSG DEBUG sqlite3QueryResGet failed.Query:%s ERROR shutting down AP:%s DEBUG profile %s not found ERROR APCtx Found DEBUG sqlite3QueryResGet failed.Query:%s ERROR APCtx Not-Found DEBUG Interface name and policy must be specified ERROR node not found *:*:*:%x:%x:%x DEBUG Interface name and policy must be specified ERROR error installing unicast key for %s DEBUG invalid ACL type %d ERROR cmd =%d i_type =%d i_val=%d DEBUG interface name not specified ERROR join event for new node %s DEBUG interface name not specified ERROR wpa/rsn IE id %d/%d not supported DEBUG Invalid interface - %s specified ERROR wpa IE id %d not supported DEBUG buffer length not specified ERROR leave event for node %s DEBUG Invalid length(%d) specified ERROR NodeFree request for node : %s DEBUG failed created iappdLock ERROR installing key to index %d DEBUG failed to create cipher contexts. ERROR iReq.i_val : %d DEBUG unable to register to UMI ERROR pIfName : %s DEBUG iappSockInit() failed ERROR iReq.i_val : %d DEBUG iappInit got error, unregistering it with UMI ERROR setting mode: %d DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) failed ERROR Global counter wrapped, re-generating... DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) failed ERROR
Unified Services Router User Manual 169 Got PNAC_EVENT_PREAUTH_SUCCESS event for : %s DEBUG UDP failed, received Length is %d ERROR event for non-existent node %s DEBUG umiIoctl(UMI_COMP_KDOT11, ERROR PNAC_EVENT_EAPOL_START event received DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) \ ERROR PNAC_EVENT_EAPOL_LOGOFF event received DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) \ ERROR PNAC_EVENT_REAUTH event received DEBUG No IAPP Node found for req id %d ERROR PNAC_EVENT_AUTH_SUCCESS event received DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) \ ERROR PNAC_EVENT_PORT_STATUS_CHANGED event received DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) \ ERROR unsupported event %d from PNAC DEBUG umiIoctl(UMI_COMP_UDOT11,%d,%d) failed ERROR event for non-existent node %s. Create new node. DEBUG UDP socket is not created ERROR Add new node to DOT11 Node list DEBUG UDP send failed ERROR Update dot11STA database DEBUG IAPP: socket (SOCK_STREAM) failed. ERROR Add PMKSA to the list DEBUG IAPP: TCP connect failed to %s. ERROR eapolRecvAuthKeyMsg: received key message DEBUG cmd %d not supported.sender=%d ERROR node not found DEBUG umiIoctl(UMI_COMP_KDOT11,%d,%d) failed ERROR eapolRecvKeyMsg: replay counter not incremented DEBUG IAPP-CACHE-NOTIFY-REQUEST send to ERROR eapolRecvKeyMsg: replay counter is not same DEBUG ./src/dot11/iapp/iappLib.c:1314: ADP_ERROR ( ERROR processing pairwise key message 2 DEBUG BSSID value passed is NULL ERROR RSN IE matching: OK DEBUG reserved requestId is passed ERROR processing pairwise key message 4 DEBUG interface name is NULL ERROR processing group key message 2 DEBUG IP address value passed is NULL ERROR processing key request message from client DEBUG opening receive UDP socket failed ERROR WPA version %2x %2x not supported DEBUG enabling broadcast for UDP socket failed ERROR (%s) group cipher %2x doesn't match DEBUG opening receive TCP socket for new AP failed ERROR (%s)Pairwise cipher %s not supported DEBUG ./src/dot11/iapp/iappLib.c:1784: ADP_ERROR( ERROR (%s) authentication method %d not supported DEBUG ./src/dot11/iapp/iappLib.c:1794: ADP_ERROR( ERROR %s:Auth method=%s pairwise cipher=%s IE size=%d DEBUG ./src/dot11/iapp/iappLib.c:1803: ADP_ERROR( ERROR WPA version %2x %2x not supported DEBUG failed created dot11dLock. ERROR Unable to obtain IE of type %d DEBUG failed initialize profile library. ERROR PTK state changed from %s to %s DEBUG failed to create cipher contexts. ERROR using PMKSA from cache DEBUG unable to register to UMI ERROR PTK GK state changed from %s to %s DEBUG could not create MIB tree ERROR GK state changed from %s to %s DEBUG unable to register to PNAC ERROR Sending PTK Msg1 DEBUG Max registration attempts by DOT11 to PNAC exceeded ERROR Sending PTK Msg3 DEBUG Creation of EAP WPS Profile Failed ERROR Sending GTK Msg1 DEBUG umiIoctl(UMI_COMP_IAPP,%d ) failed ERROR
Unified Services Router User Manual 170 sending EAPOL pdu to PNAC... DEBUG DOT11_RX_EAPOL_KEYMSG: unknown ifname %s ERROR creating pnac authenticator with values %d %d - %s DEBUG cmd %d not supported.sender=%d ERROR Profile %s does not exist DEBUG inteface name passed is NULL ERROR IAPP initialized. DEBUG BSSID passed is NULL ERROR Encrypting context key=%s for DEBUG inteface name passed is NULL ERROR could not find access point context for %s DEBUG unable to allocate memory for DOT11_CTX ERROR join event for existing node %s DEBUG unable to install wme mapping on %s ERROR failed to send PNAC_FORCE_AUTHORIZED " DEBUG unable to get %s mac address ERROR failed to send PNAC_AUTHORIZED " DEBUG Failed to set %s SSID ERROR failed to send PNAC_VAR_KEY_AVAILABLE (TRUE) " DEBUG Failed to set SSID broadcast status ERROR failed to send PNAC_VAR_KEY_TX_EN (TRUE) " DEBUG Failed to set PreAuth mode ERROR failed to send PNAC_VAR_KEY_TX_EN (FALSE) " DEBUG unable to install key ERROR failed to send PNAC_FORCE_AUTHORIZED " DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_AUTHMODE failed ERROR failed to send PNAC_AUTHORIZED " DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_PRIVACY failed ERROR mic verification: OK DEBUG wpaInit failed ERROR pnacIfConfig: Invalid supplicant" DEBUG dot11InstallProfile: unable to get interface index ERROR Failed to process user request DEBUG adpHmacInit(%s) failed ERROR Failed to process user request - %s(%d) DEBUG interface %s not found ERROR pnacIfConfigUmiIoctl: umiIoctl failed DEBUG AP not found on %s ERROR pnacIfConfigUmiIoctl: usrPnac returned %d DEBUG keyLen > PNAC_KEY_MAX_SIZE ERROR pnacIfConfigUmiIoctl: usrPnac returned %d DEBUG Invalid profile name passed ERROR pnacIfConfigUmiIoctl: usrPnac returned %d DEBUG Creation of WPS EAP Profile failed ERROR pnacKernNotifier: invalid PAE configuration " DEBUG unsupported command %d ERROR From pnacEapDemoAuthRecv: unsupported response " DEBUG device %s not found ERROR From pnacEapDemoAuthRecv: invalid codes received DEBUG unsupported command %d ERROR From pnacRadXlateDemoRecv: received unknown " DEBUG dot11NodeAlloc failed ERROR From pnacRadXlateDemoRecv: invalid codes received DEBUG Getting WPA IE failed for %s ERROR Error from pnacRadXlateDemoRecv: malloc failed DEBUG Getting WPS IE failed for %s ERROR From pnacRadXlateRadPktHandle: received a non-supported" DEBUG Failed initialize authenticator for node %s ERROR Only md5 authentication scheme currently supported. " DEBUG Failed to get the system up time while adding node %s ERROR Message from authenticator: DEBUG error creating PNAC port for node %s ERROR from pnacPDUXmit: bufsize = %d, pktType = %d," DEBUG dot11NodeAlloc failed ERROR pnacPDUXmit: sending eap packet. code = %d, " DEBUG Invalid arguments. ERROR
Unified Services Router User Manual 171 pnacRecvRtn: no corresponding pnac port pae found DEBUG umiIoctl(UMI_COMP_IAPP,%d) failed ERROR sending unicast key DEBUG Invalid IE. ERROR sending broadcast key DEBUG umiIoctl(UMI_COMP_KDOT11_VAP,%d ) failed ERROR from pnacAuthPAEDisconnected: calling pnacTxCannedFail DEBUG umiIoctl(UMI_COMP_KDOT11,%d ,%d) failed ERROR from pnacAuthPAEForceUnauth: calling pnacTxCannedFail DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_CWMIN failed ERROR state changed from %s to %s DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_CWMAX failed ERROR PNAC user comp id not set. dropping event %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_AIFS failed ERROR sending event %d to %d DEBUG KDOT11_SET_PARAM:80211_IOC_WME_TXOPLIMIT failed ERROR requesting keys informantion from %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME_ACM failed ERROR pnacUmiPortPaeParamSet: error in getting port pae DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WME failed ERROR pnacUmiPortPaeParamSet: invalid param - %d DEBUG invalid group cipher %d ERROR pnacRecvASInfoMessage: Skey of length %d set DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_MCASTCIPHER failed ERROR pnacRecvASInfoMessage: reAuthPeriod set to: %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_MCASTKEYLEN failed ERROR pnacRecvASInfoMessage: suppTimeout set to: %d DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_UCASTCIPHERS failed ERROR PORT SUCCESSFULLY DESTROYED DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_KEYMGTALGS failed ERROR creating physical port for %s DEBUG KDOT11_SET_PARAM:IEEE80211_IOC_WPA failed ERROR pnacAuthInit: using defualt pnacAuthParams DEBUG unknow cipher type = %d ERROR pnacSuppInit: using defualt pnacSuppParams DEBUG umiIoctl(UMI_COMP_IAPP,%d) failed ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG invalid media value=%d ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG invalid mediaOpt value=%d ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG invalid mode value=%d ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG dot11PnacIfCreate failed ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG wpaPRF failed ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG Error generating global key counter ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG wpaCalcMic: unsupported key descriptor version ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG integrity failed. need to stop all stations " ERROR Error from pnacCombinedStMachTriggerFunc: " DEBUG couldn't find AP context for %s interface ERROR received a pdu on %s DEBUG dot11Malloc failed ERROR pnacRecvMapi: protoType: %04x pPhyPort->authToASSendRtn:%p DEBUG dot11Malloc failed ERROR port not found DEBUG eapolRecvKeyMsg: unknown descType =%d ERROR
Unified Services Router User Manual 172 from pnacRecvMapi: pkt body len = %d, pktType = %d DEBUG eapolRecvKeyMsg: invalid descriptor version ERROR from pnacPDUProcess: received PNAC_EAP_PACKET DEBUG eapolRecvKeyMsg: incorrect descriptor version ERROR from pnacPDUProcess: currentId = %d DEBUG eapolRecvKeyMsg: Ack must not be set ERROR from pnacPDUProcess: code = %d, identifier = %d, " DEBUG eapolRecvKeyMsg: MIC bit must be set ERROR from pnacPDUProcess: setting rxResp true DEBUG wpaAuthRecvPTKMsg2: unexpected packet received ERROR from pnacPDUProcess: code = %d, identifier = %d, " DEBUG wpaAuthRecvPTKMsg2: mic check failed ERROR from pnacPDUProcess: received " DEBUG wpaAuthRecvPTKMsg2: rsn ie mismatch ERROR from pnacPDUProcess: received " DEBUG wpaAuthRecvPTKMsg4: unexpected packet received ERROR from pnacPDUProcess: received PNAC_EAPOL_KEY_PACKET DEBUG wpaAuthRecvPTKMsg4: keyDataLength not zero ERROR doing pnacTxCannedFail DEBUG wpaAuthRecvPTKMsg4: mic check failed ERROR doing pnacTxCannedSuccess DEBUG wpaAuthRecvGTKMsg2: unexpected packet received ERROR doing pnacTxReqId DEBUG secureBit not set in GTK Msg2 ERROR doing pnacTxReq DEBUG wpaAuthRecvGTKMsg2: keyDataLength not zero ERROR doing pnacTxStart DEBUG wpaAuthRecvGTKMsg2: mic check failed ERROR doing pnacTxLogoff DEBUG wpaAuthRecvKeyReq: unexpected packet received ERROR doing pnacTxRspId: 1st cond DEBUG wpaAuthRecvKeyReq: keyDataLength not zero ERROR doing pnacTxRspId: entering 2nd cond DEBUG wpaAuthRecvKeyReq: mic check failed ERROR from pnacTxRspId: code = %d, identifier = %d, length = %d, " DEBUG invalid OUI %x %x %x ERROR doing pnacTxRspId: 2nd cond DEBUG (%s) invalid OUI %x %x %x ERROR doing pnacTxRspAuth: 1st cond DEBUG [%s:%d] Cipher in WPA IE : %x ERROR doing pnacTxRspAuth: 2nd cond DEBUG (%s) invalid OUI %x %x %x ERROR message for unknown port PAE DEBUG short WPA IE (length = %d) received ERROR from pnacACToSuppRecvRtn: calling pnacEapPktRecord DEBUG PTK state machine in unknown state. ERROR from pnacEapPktRecord: code = %d, identifier = %d, " DEBUG dot11InstallKeys failed ERROR from pnacEapPktRecord: received success pkt DEBUG group state machine entered into WPA_AUTH_GTK_INIT ERROR from pnacEapPktRecord: received failure pkt DEBUG dot11Malloc failed ERROR from pnacEapPktRecord: received request pkt DEBUG dot11Malloc failed ERROR unknown EAP-code %d DEBUG dot11Malloc failed ERROR Authenticator[%d]: DEBUG aesWrap failed ERROR Auth PAE state = %s DEBUG unknown key descriptor version %d ERROR Auth Reauth state = %s DEBUG dot11Malloc failed ERROR Back auth state = %s DEBUG could not initialize AES128ECB ERROR Supplicant[%d]: DEBUG could not initialize AES-128-ECB ERROR Supp Pae state = %s DEBUG MD5 initialization failed ERROR
Unified Services Router User Manual 173 from pnacBackAuthFail: calling pnacTxCannedFail DEBUG RC4 framework initialization failed ERROR %s returned ERROR DEBUG PNAC framework initialization failed ERROR pnacUmiIoctlHandler: cmd: %s(%d) DEBUG ERROR: option value not specified ERROR %s not configured for 802.1x DEBUG ERROR: -u can be used only with -s ERROR could not process PDU received from the wire DEBUG ERROR: user-name not specified ERROR pnacPDUForward: failed to foward the received PDU DEBUG failed to enable debug ERROR Creating PHY port with AUTH backend : %s SendRtn: %p RecvRtn:%p DEBUG [%s]: failed to convert string to MAC " ERROR pnacUmiAuthConfig: %s not configured for 802.1x DEBUG failed to initialize UMI ERROR pnacSuppRegisterUserInfo: not a valid AC DEBUG pnacPhyPortParamSet:invalid arguments ERROR pnacIfConfig: autoAuth Enabled DEBUG pnacPhyPortParamSet:Failed to create socket ERROR pnacSendRtn: no pnac port pae found for " DEBUG Error from pnacPhyPortParamSet:%s-device invalid ERROR sending portStatus: %s[%d] to dot11 DEBUG Error from pnacPhyPortParamSet:%s-Getting MAC address " ERROR pnacRecvASInfoMessage: Rkey of length %d set DEBUG pnacPhyPortParamSet:Failed to add 802.1X multicast " ERROR ASSendRtn: %p ASToAuthRecv: %p DEBUG pnacIsInterfaceUp: failed to create a raw socket ERROR adpRand failed:unable to generate random unicast key WARN pnacIsInterfaceUp: failed to get interface flags ERROR using group key as unicast key WARN failed to allocate buffer ERROR Integrity check failed more than once in last 60 secs. WARN UMI initialization failed ERROR MIC failed twice in last 60 secs, taking countermeasures WARN UMI initialization failed ERROR Failed to set dot11 port status WARN Error from pnacEapDemoAuthLibInit: malloc failed ERROR PTK state machine in NO_STATE. WARN Error from pnacEapDemoAuthRecv: received null EAP pkt ERROR PTK state machine in NO_STATE!! WARN Error from pnacEapDemoAuthRecv: send " ERROR PMKSA refcount not 1 WARN Error from pnacRadXlateASAdd: cannot open socket ERROR IV verification failednknown subtype> WARN Error from pnacRadXlateDemoRecv: received null EAP pkt ERROR pnacIfConfig: overwriting previous interface " WARN From pnacRadXlateDemoRecv: send " ERROR pnacIfConfig: overwriting previous " WARN Error from pnacRadXlateDemoRecv: radius " ERROR pnacIfConfig: overwriting previous username" WARN Error from pnacRadXlateDemoRecv: radius " ERROR pnacIfConfig: overwriting previous password" WARN Error from pnacRadXlateRadIdRespSend: send to failed ERROR %s: Failed to set port status WARN Error from pnacRadXlateRadNonIdRespSend: send to failed ERROR %s: Failed to notify event to dot11 WARN Error from pnacRadXlateRadRecvProc: recvfrom failed ERROR pnacLibDeinit: Failed to destroy the WARN From ERROR
Unified Services Router User Manual 174 phyPort:%s pnacRadXlateRadPktIntegrityChk: no corresponding " pnacPortPaeDeconfig:kpnacPortPaeDeconfig failed WARN Error from pnacRadXlateRadPktIntegrityChk: no message " ERROR pnacPortPaeDeconfig:kpnacPortPaeDeconfig failed WARN Error from pnacRadXlateRadPktIntegrityChk: " ERROR pnacBackAuthSuccess: failed to notify the destination " WARN From pnacRadXlateRadChalPktHandle: no encapsulated eap " ERROR could not initialize MGMT framework ERROR Error from pnacRadXlateRadChalPktHandle: malloc for eap " ERROR umiInit failed ERROR Error from pnacEapDemoSuppUserInfoRegister: invalid " ERROR iappInit failed ERROR Error from pnacEapDemoSuppRecv: received null EAP pkt ERROR could not initialize IAPP MGMT. ERROR Error from pnacEapDemoSuppRecv: send ptr to pnac supplicant" ERROR dot11Malloc failed ERROR From pnacEapDemoSuppRecv: user info not entered yet ERROR buffer length not specified ERROR Error from pnacEapDemoSuppRecv: couldn't " ERROR Invalid length(%d) specified ERROR MDString: adpDigestInit for md5 failed ERROR Failed to get information about authorized AP list. ERROR pnacUmiInit: UMI initialization failed ERROR Recd IE data for non-existent AP %s ERROR could not start PNAC task ERROR Recd IE data for wrong AP %s ERROR invalid aruments ERROR Received Invalid IE data from WSC ERROR pnacIfNameToIndex failed ERROR Recd IE data for non-existent AP %s ERROR pnacPhyPortParamSet: device invalid %s%d ERROR Recd WSC Start command without interface name ERROR pnacPhyPortParamSet: EIOCGADDR ioctl failed ERROR Recd WSC start for non-existent AP %s ERROR pnacPhyPortParamSet: multicast addr add ioctl failed ERROR Recd WSC start for wrong AP %s ERROR pnacPhyPortParamUnset: multicast addr del ioctl failed ERROR Unable to send WSC_WLAN_CMD_PORT to WSC ERROR pnacPDUXmit: Invalid arguments ERROR Failed to get the ap context for %s ERROR pnacPDUXmit: failed to get M_BLK_ID ERROR WPS can only be applied to WPA/WPA2 security profiles ERROR from pnacIsInterfaceUp: device %s%d invalid ERROR wpsEnable: running wsccmd failed ERROR pnacRecvRtn: dropping received packet as port is" ERROR Failed to get the ap context for %s ERROR pnacSendRtn: Invalid arguments ERROR WPS conf. under non WPA/WPA2 security setting ERROR pnacSendRtn: no physical port corresponding to" ERROR Failed to reset the Beacon Frame IE in the driver ERROR pnacSendRtn: dropping packet as port" ERROR Failed to reset the Beacon Frame IE in the driver ERROR pnacAuthBuildRC4KeyDesc: adpEncryptInit(RC4) failed ERROR WPS method cannot be NULL ERROR pnacAuthBuildRC4KeyDesc: adpCipherContextCtrl" ERROR PIN value length should be a multiple of 4 !! ERROR pnacDot11UserSet: incorrect buffer length ERROR Failed to initiate PIN based association, PIN = %s ERROR PNAC user component id not set. ERROR
Unified Services Router User Manual 175 Failed to initiate PBC based enrolle association ERROR pnacKeyInfoGet:failed to allocate buffer ERROR Invalid association mode. (Allowed modes : PIN/PBC) ERROR PNAC user comp id not set. dropping EAPOL key pkt ERROR wpsEnable: running wsccmd failed ERROR pnacUmiPortPaeParamSet: invalid buffer received ERROR Failed to send QUIT command to WSC from DOT11 ERROR Error from pnacRecvASInfoMessage: " ERROR Failed to clear off the WPS process ERROR pnacRecvASInfoMessage: " ERROR missing profile name ERROR pnacRecvASInfoMessage: Bad info length ERROR A profile exists with the same name ERROR Error from pnacLibInit: malloc failed ERROR Error in allocating memory for profile ERROR could not create phy ports lock ERROR missing profile name ERROR could not create nodes ports lock ERROR missing profile name ERROR port exists for iface - %s ERROR Profile name and interface name must be specified ERROR pnacPhyPortCreate failed ERROR Profile %s does not exist ERROR kpnacPhyPortCreate failed ERROR Could not set profile %s on the interface %s ERROR invalid argument ERROR missing profile name ERROR pnacAuthConfig: maxAuth limit reached ERROR Profile %s does not exist ERROR pnacAuthConfig: malloc failed ERROR Profile %s does not exist ERROR Error from pnacAuthConfig: pAsArg cannot be NULL ERROR SSID should not be longer than %d ERROR Error from pnacAuthConfig: receive routine hook " ERROR Profile %s does not exist ERROR pnacAuthConfig: pnacAuthInit failed ERROR Profile %s does not exist ERROR kpnacPortPaeConfig failed ERROR Profile %s does not exist ERROR Invalid arguments ERROR Profile %s does not exist ERROR Error from pnacSuppConfig: malloc failed ERROR Profile %s does not exist ERROR Error from pnacSuppConfig: receive routine hook " ERROR Profile %s does not exist ERROR Error from pnacSuppConfig: pnacSuppInit failed ERROR SSID not set. SSID is needed to generate password hash ERROR kpnacPortPaeConfig failed ERROR Password string too big ERROR pnacAuthDeconfig failed: pPortPae NULL ERROR dot11Malloc failed ERROR Error from pnacPhyPortDestroy: port not configured ERROR Profile %s does not exist ERROR pnacPhyPortDestroy: Failed to deconfigure port ERROR Hex string should only have %d hex chars ERROR pnacPhyPortParamUnset FAILED ERROR dot11Malloc failed ERROR Error from pnacPhyPortCreate: malloc failed ERROR Profile %s does not exist ERROR Error from pnacPhyPortCreate: pnacPhyPortParamSet" ERROR invalid key index %d. key index should be 0-3. ERROR error from pnacPhyPortCreate: malloc failed ERROR wepKey length incorrect ERROR Error from pnacAuthInit: pnacPortTimersInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacAuthPAEInit failed ERROR
Unified Services Router User Manual 176 Invalid Cipher type %d ERROR Error from pnacAuthInit: pnacAuthKeyTxInit failed ERROR Profile supports WEP stas,Group cipher must be WEP ERROR Error from pnacAuthInit: pnacReauthTimerInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacBackAuthInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacCtrlDirInit failed ERROR Profile %s does not exist ERROR Error from pnacAuthInit: pnacKeyRecvInit failed ERROR invalid pairwise cipher type %d ERROR Error from pnacSuppInit: malloc failed ERROR Cipher %s is already in the list. ERROR Error from pnacSuppInit: pnacPortTimersInit failed ERROR Profile %s does not exist ERROR Error from pnacSuppInit: pnacKeyRecvInit failed ERROR Invalid Cipher type %d ERROR Error from pnacSuppInit: pnacSuppKeyTxInit failed ERROR Cipher %s not found in the list. ERROR Error from pnacSuppInit: pnacSuppPAEInit failed ERROR Profile %s does not exist ERROR Error from pnacRecvRtn: invalid arguments ERROR Profile %s does not exist ERROR Error from pnacRecvMapi: unsupported PDU received ERROR Auth method %s is already in the list ERROR suppToACSendRtn returned not OK! ERROR Profile %s does not exist ERROR Error from pnacBasicPktCreate: malloc failed ERROR Auth method %s not found in the list. ERROR Error from pnacEAPPktCreate: basic pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxCannedFail: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxCannedSuccess: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxReqId: eap pkt create failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacTxReq: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacSendRespToServer: malloc failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacSendRespToServer: no AS configured ERROR Profile %s does not exist ERROR Error from pnacTxStart: basic pkt create failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacTxStart: basic pkt create failed ERROR Profile %s does not exist ERROR Error from pnacTxRspId: eap pkt create failed ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacTxRspAuth: eap pkt create failed ERROR Profile %s does not exist ERROR Error from pnacEapPktRecord: EAP packet too" ERROR invalid type value %d. supported values are 1,2,3,4 ERROR Error from pnacEapPktRecord: " ERROR Profile %s does not exist ERROR from pnacBackAuthTimeout: calling pnacTxCannedFail ERROR ERROR: incomplete DB update information. ERROR hmac_md5: adpHmacContextCreate failed ERROR old values result does not contain 2 rows ERROR hmac_md5:adpHmacInit failed ERROR sqlite3QueryResGet failed ERROR pnacUmiIoctlHandler: invalid cmd: %d ERROR
Unified Services Router User Manual 177 Error in executing DB update handler ERROR pnacEapRadAuthSend: Invalid arguments ERROR sqlite3QueryResGet failed ERROR pnacEapRadAuthSend: failed to allocate inbuffer ERROR ERROR: incomplete DB update information. ERROR pnacXmit : umiIoctl failed[%d] ERROR old values result does not contain 2 rows ERROR pnacPDUForward: Invalid input ERROR sqlite3QueryResGet failed ERROR pnacPDUForward: error in getting port pae information ERROR Error in executing DB update handler ERROR pnacPDUForward: error allocating memory ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiIfMacAddrChange: %s not configured for 802.1x ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiIfMacAddrChange: could not process PDU received" ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiPhyPortConfig: Invalid config data ERROR sqlite3QueryResGet failed.Query:%s ERROR pnacUmiPhyPortConfig: Invalid backend name specified ERROR startStopVap failed to stop %s ERROR pnacUmiPhyPortConfig: could not create PNAC physical" ERROR Invalid SQLITE operation code - %d ERROR pnacUmiAuthConfig: Invalid config data ERROR ./src/dot11/mgmt/dot11Mgmt.c:1177: ADP_ERROR ( ERROR pnacUmiAuthConfig: Invalid backend name specified ERROR only delete event expected on dot11RogueAP. ERROR unable to create new EAP context. ERROR sqlite3QueryResGet failed ERROR unable to apply %s profile on the EAP context. ERROR unhandled database operation %d ERROR pnacUmiAuthConfig: could not configure PNAC PAE " ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: Invalid config data ERROR failed to configure WPS on %s ERROR pnacUmiSuppConfig: Invalid backend name specified ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: %s not configured for 802.1x ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: could not PNAC port Access" ERROR sqlite3QueryResGet failed ERROR pnacUmiSuppConfig: Failed to register user information ERROR sqlite3QueryResGet failed ERROR pnacPortByMacDeconfig: port not found ERROR sqlite3QueryResGet failed ERROR pnacPortByMacDeconfig: port not found ERROR no VAP rows returned. expected one ERROR pnacUmiIfDown: Invalid config data ERROR multiple VAP rows returned. expected one ERROR pnacUmiIfDown: Invalid config data ERROR sqlite3QueryResGet failed ERROR Error from pnacPortDeconfig: port not configured ERROR invalid query result. ncols=%d nrows=%d ERROR pnacUmiIfDown: could not de-configure port ERROR %s:VAP(%s) create failed ERROR pnacUmiPhyPortDestroy: Invalid config data ERROR sqlite3QueryResGet failed ERROR pnacUmiPhyPortDestroy: Invalid config data ERROR invalid query result. ncols=%d nrows=%d ERROR pnacUmiPhyPortDestroy: Failed to destroy the port ERROR
Unified Services Router User Manual 178 Invalid config data ERROR Facility: Kernel Log Message Severity Log Message Severity DNAT: multiple ranges no longer supported DEBUG %s: %s%s:%d -> %s:%d %s, DEBUG DNAT: Target size %u wrong for %u ranges, DEBUG %s: %s%s:%d %s, DEBUG DNAT: wrong table %s, tablename DEBUG %s: Failed to add WDS MAC: %s, dev->name, DEBUG DNAT: hook mask 0x%x bad, hook_mask DEBUG %s: Device already has WDS mac address attached, DEBUG %s%d: resetting MPPC/MPPE compressor, DEBUG %s: Added WDS MAC: %s, dev->name, DEBUG %s%d: wrong offset value: %d, DEBUG %s: WDS MAC address %s is not known by this interface, DEBUG %s%d: wrong length of match value: %d, DEBUG [madwifi] %s() : Not enough space., __FUNCTION__ DEBUG %s%d: too big offset value: %d, DEBUG Returning to chan %d, ieeeChan DEBUG %s%d: cannot decode offset value, DEBUG WEP DEBUG %s%d: wrong length code: 0x%X, DEBUG AES DEBUG %s%d: short packet (len=%d), __FUNCTION__, DEBUG AES_CCM DEBUG %s%d: bad sequence number: %d, expected: %d, DEBUG CKIP DEBUG %s%d: bad sequence number: %d, expected: %d, DEBUG TKIP DEBUG PPPIOCDETACH file->f_count=%d, DEBUG %s: cannot map channel to mode; freq %u flags 0x%x, DEBUG PPP: outbound frame not passed DEBUG %s: %s, vap->iv_dev->name, buf DEBUG PPP: VJ decompression error DEBUG %s: [%s] %s, vap->iv_dev->name, DEBUG PPP: inbound frame not passed DEBUG %s: [%s] %s, vap->iv_dev->name, ether_sprintf(mac), buf DEBUG PPP: reconstructed packet DEBUG [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG PPP: no memory for DEBUG [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG missed pkts %u..%u, DEBUG [%s:%s] discard %s information element, %s, DEBUG %s%d: resetting MPPC/MPPE compressor, DEBUG [%s:%s] discard information element, %s, DEBUG %s%d: wrong offset value: %d, DEBUG [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG %s%d: wrong length of match value: %d, DEBUG [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG %s%d: too big offset value: %d, DEBUG ifmedia_add: null ifm DEBUG %s%d: cannot decode offset value, DEBUG Adding entry for DEBUG %s%d: wrong length code: 0x%X, DEBUG ifmedia_set: no match for 0x%x/0x%x, DEBUG %s%d: short packet (len=%d), __FUNCTION__, DEBUG ifmedia_set: target DEBUG %s%d: bad sequence number: %d, expected: %d, DEBUG ifmedia_set: setting to DEBUG
Unified Services Router User Manual 179 %s%d: bad sequence number: %d, expected: %d, DEBUG ifmedia_ioctl: no media found for 0x%x, DEBUG PPPIOCDETACH file->f_count=%d, DEBUG ifmedia_ioctl: switching %s to , dev->name DEBUG PPP: outbound frame not passed DEBUG ifmedia_match: multiple match for DEBUG PPP: VJ decompression error DEBUG <unknown type> DEBUG PPP: inbound frame not passed DEBUG desc->ifmt_string DEBUG PPP: reconstructed packet DEBUG mode %s, desc->ifmt_string DEBUG PPP: no memory for DEBUG <unknown subtype> DEBUG missed pkts %u..%u, DEBUG %s, desc->ifmt_string DEBUG %s: INC_USE_COUNT, now %d, __FUNCTION__, mod_use_count \ DEBUG %s%s, seen_option++ ? , : , DEBUG %s: DEC_USE_COUNT, now %d, __FUNCTION__, mod_use_count \ DEBUG %s%s, seen_option++ ? , : , DEBUG PPPOL2TP %s: _fmt, DEBUG %s, seen_option ? > : DEBUG PPPOL2TP: --> %s, __FUNCTION__) DEBUG %s: %s, dev->name, buf DEBUG PPPOL2TP: <-- %s, __FUNCTION__) DEBUG %s: no memory for sysctl table!, __func__ DEBUG %s: recv: , tunnel->name DEBUG %s: no memory for VAP name!, __func__ DEBUG %s: xmit:, session->name DEBUG %s: failed to register sysctls!, vap->iv_dev->name DEBUG %s: xmit:, session->name DEBUG %s: no memory for new proc entry (%s)!, __func__, DEBUG %s: module use_count is %d, __FUNCTION__, mod_use_count DEBUG %s: 0x%p len %u, tag, p, len DEBUG PPPOL2TP %s: _fmt, DEBUG %03d:, i DEBUG PPPOL2TP: --> %s, __FUNCTION__) DEBUG %02x, ((u_int8_t *)p)[i] DEBUG PPPOL2TP: <-- %s, __FUNCTION__) DEBUG first difference at byte %u, i DEBUG %s: recv: , tunnel->name DEBUG %s: , t->name DEBUG %s: xmit:, session->name DEBUG FAIL: ieee80211_crypto_newkey failed DEBUG %s: xmit:, session->name DEBUG FAIL: ieee80211_crypto_setkey failed DEBUG PPPOL2TP %s: _fmt, DEBUG FAIL: unable to allocate skbuff DEBUG PPPOL2TP: --> %s, __FUNCTION__) DEBUG FAIL: wep decap failed DEBUG PPPOL2TP: <-- %s, __FUNCTION__) DEBUG FAIL: decap botch; length mismatch DEBUG %s: recv: , tunnel->name DEBUG FAIL: decap botch; data does not compare DEBUG %s: xmit:, session->name DEBUG FAIL: wep encap failed DEBUG %s: xmit:, session->name DEBUG FAIL: encap data length mismatch DEBUG IRQ 31 is triggered DEBUG FAIL: encrypt data does not compare DEBUG [%s:%d] , __func__, __LINE__\ DEBUG PASS DEBUG \t[R%s %#0x %#0x 0x%08x%08x], (status == ERROR ? # : ), page, addr, (uint32_t)(*pValue >> 32), (uint32_t)(*pValue & 0xffffffff) DEBUG %u of %u 802.11i WEP test vectors passed, pass, total DEBUG \t[W%s %#0x %#0x 0x%08x%08x], (status == ERROR ? # : ), page, addr, (uint32_t)(value >> 32), (uint32_t)(value & 0xffffffff) DEBUG %s: 0x%p len %u, tag, p, len DEBUG %s: mac_add %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG %03d:, i DEBUG
Unified Services Router User Manual 180 %s: mac_del %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG %02x, ((u_int8_t *)p)[i] DEBUG %s: mac_kick %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG first difference at byte %u, i DEBUG %s: mac_undefined %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG %s: , t->name DEBUG %s: addr_add %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG FAIL: ieee80211_crypto_newkey failed DEBUG %s: addr_del %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG FAIL: ieee80211_crypto_setkey failed DEBUG %s: mac_undefined %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] DEBUG FAIL: unable to allocate skbuff DEBUG %s: set_float %d;%d, DEBUG FAIL: ccmp encap failed DEBUG IRQ 32 is triggered DEBUG FAIL: encap data length mismatch DEBUG ip_finish_output2: No header cache and no neighbour! DEBUG FAIL: encrypt data does not compare DEBUG a guy asks for address mask. Who is it? DEBUG FAIL: ccmp decap failed DEBUG icmp v4 hw csum failure) DEBUG FAIL: decap botch; length mismatch DEBUG expire>> %u %d %d %d, expire, DEBUG FAIL: decap botch; data does not compare DEBUG expire++ %u %d %d %d, expire, DEBUG PASS DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG %u of %u 802.11i AES-CCMP test vectors passed, pass, total DEBUG rt_bind_peer(0) @%p, NET_CALLER(iph) DEBUG %s: 0x%p len %u, tag, p, len DEBUG ip_rt_advice: redirect to DEBUG %03d:, i DEBUG ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG %02x, ((u_int8_t *)p)[i] DEBUG udp cork app bug 2) DEBUG first difference at byte %u, i DEBUG udp cork app bug 3) DEBUG ieee80211_crypto_newkey failed DEBUG udp v4 hw csum failure.) DEBUG ieee80211_crypto_setkey failed DEBUG UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, DEBUG unable to allocate skbuff DEBUG UDP: bad checksum. From %d.%d.%d.%d:%d to %d.%d.%d.%d:%d ulen %d, DEBUG tkip enmic failed DEBUG %s: lookup policy [list] found=%s, DEBUG enmic botch; length mismatch DEBUG %s: called: [output START], __FUNCTION__ DEBUG enmic botch DEBUG %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_dst, family) DEBUG tkip encap failed DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_src, family) DEBUG encrypt phase1 botch DEBUG
Unified Services Router User Manual 181 %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_dst, family) DEBUG encrypt data length mismatch DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_src, family) DEBUG encrypt data does not compare DEBUG a guy asks for address mask. Who is it? DEBUG tkip decap failed DEBUG icmp v4 hw csum failure) DEBUG decrypt phase1 botch DEBUG expire>> %u %d %d %d, expire, DEBUG decrypt data does not compare DEBUG expire++ %u %d %d %d, expire, DEBUG decap botch; length mismatch DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG decap botch; data does not compare DEBUG rt_bind_peer(0) @%p, NET_CALLER(iph) DEBUG tkip demic failed DEBUG ip_rt_advice: redirect to DEBUG 802.11i TKIP test vectors passed DEBUG ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG %s, buf DEBUG UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, DEBUG Atheros HAL assertion failure: %s: line %u: %s, DEBUG UDP: bad checksum. From %d.%d.%d.%d:%d to %d.%d.%d.%d:%d ulen %d, DEBUG ath_hal: logging to %s %s, ath_hal_logfile, DEBUG a guy asks for address mask. Who is it? DEBUG ath_hal: logging disabled DEBUG fib_add_ifaddr: bug: prim == NULL DEBUG %s%s, sep, ath_hal_buildopts[i] DEBUG fib_del_ifaddr: bug: prim == NULL DEBUG ath_pci: No devices found, driver not installed. DEBUG expire>> %u %d %d %d, expire, DEBUG _fmt, __VA_ARGS__ DEBUG expire++ %u %d %d %d, expire, DEBUG %s: Warning, using only %u entries in %u key cache, DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG %s: TX99 support enabled, dev->name DEBUG rt_bind_peer(0) @%p, DEBUG %s:grppoll Buf allocation failed ,__func__ DEBUG ip_rt_advice: redirect to DEBUG %s: %s: unable to start recv logic, DEBUG ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG %s: %s: unable to start recv logic, DEBUG %s: lookup policy [list] found=%s, DEBUG %s: no skbuff, __func__ DEBUG %s: called: [output START], __FUNCTION__ DEBUG %s: hardware error; resetting, dev->name DEBUG %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_dst, family) DEBUG %s: rx FIFO overrun; resetting, dev->name DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl4_src, family) DEBUG %s: unable to reset hardware: '%s' (HAL status %u) DEBUG %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_dst, family) DEBUG %s: unable to start recv logic, dev->name DEBUG %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_src, family) DEBUG %s: %s: unable to reset hardware: '%s' (HAL status %u), DEBUG a guy asks for address mask. Who is it? DEBUG %s: %s: unable to start recv logic, DEBUG icmp v4 hw csum failure) DEBUG ath_mgtstart: discard, no xmit buf DEBUG expire>> %u %d %d %d, expire, DEBUG %s: [%02u] %-7s , tag, ix, ciphers[hk->kv_type] DEBUG expire++ %u %d %d %d, expire, DEBUG %02x, hk->kv_val[i] DEBUG rt_cache @%02x: %u.%u.%u.%u, hash, DEBUG mac %s, ether_sprintf(mac) DEBUG rt_bind_peer(0) @%p, NET_CALLER(iph) DEBUG %s , sc->sc_splitmic ? mic : rxmic DEBUG ip_rt_advice: redirect to DEBUG %02x, hk->kv_mic[i] DEBUG
Unified Services Router User Manual 182 ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, DEBUG txmic DEBUG UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, DEBUG %02x, hk->kv_txmic[i] DEBUG UDP: bad checksum. From %d.%d.%d.%d:%d to %d.%d.%d.%d:%d ulen %d, DEBUG %s: unable to update h/w beacon queue parameters, DEBUG REJECT: ECHOREPLY no longer supported. DEBUG %s: stuck beacon; resetting (bmiss count %u), DEBUG ipt_rpc: only valid for PRE_ROUTING, FORWARD, POST_ROUTING, LOCAL_IN and/or LOCAL_OUT targets. DEBUG move data from NORMAL to XR DEBUG ip_nat_init: can't setup rules. DEBUG moved %d buffers from NORMAL to XR, index DEBUG ip_nat_init: can't register in hook. DEBUG move buffers from XR to NORMAL DEBUG ip_nat_init: can't register out hook. DEBUG moved %d buffers from XR to NORMAL, count DEBUG ip_nat_init: can't register adjust in hook. DEBUG %s:%d %s, __FILE__, __LINE__, __func__ DEBUG ip_nat_init: can't register adjust out hook. DEBUG %s:%d %s, __FILE__, __LINE__, __func__ DEBUG ip_nat_init: can't register local out hook. DEBUG %s: no buffer (%s), dev->name, __func__ DEBUG ip_nat_init: can't register local in hook. DEBUG %s: no skbuff (%s), dev->name, __func__ DEBUG ipt_hook: happy cracking. DEBUG %s: HAL qnum %u out of range, max %u!, DEBUG ip_conntrack: can't register pre-routing defrag hook. DEBUG grppoll_start: grppoll Buf allocation failed DEBUG ip_conntrack: can't register local_out defrag hook. DEBUG %s: HAL qnum %u out of range, max %u!, DEBUG ip_conntrack: can't register pre-routing hook. DEBUG %s: AC %u out of range, max %u!, DEBUG ip_conntrack: can't register local out hook. DEBUG %s: unable to update hardware queue DEBUG ip_conntrack: can't register local in helper hook. DEBUG %s: bogus frame type 0x%x (%s), dev->name, DEBUG ip_conntrack: can't register postrouting helper hook. DEBUG ath_stoprecv: rx queue 0x%x, link %p, DEBUG ip_conntrack: can't register post-routing hook. DEBUG %s: %s: unable to reset channel %u (%u MHz) DEBUG ip_conntrack: can't register local in hook. DEBUG %s: %s: unable to restart recv logic, DEBUG ip_conntrack: can't register to sysctl. DEBUG %s: unable to allocate channel table, dev->name DEBUG ip_conntrack_rtsp v IP_NF_RTSP_VERSION loading DEBUG %s: unable to allocate channel table, dev->name DEBUG ip_conntrack_rtsp: max_outstanding must be a positive integer DEBUG %s: unable to collect channel list from HAL; DEBUG ip_conntrack_rtsp: setup_timeout must be a positive integer DEBUG R (%p %llx) %08x %08x %08x %08x %08x %08x %c, DEBUG ip_conntrack_rtsp: ERROR registering port %d, ports[i] DEBUG T (%p %llx) %08x %08x %08x %08x %08x %08x %08x %08x %c, DEBUG ip_nat_rtsp v IP_NF_RTSP_VERSION loading DEBUG %s: no memory for sysctl table!, __func__ DEBUG %s: Sorry! Cannot find this match option., __FILE__ DEBUG %s: no memory for device name storage!, __func__ DEBUG ipt_time loading DEBUG %s: failed to register sysctls!, sc- DEBUG
Unified Services Router User Manual 183 >sc_dev->name ipt_time unloaded DEBUG %s: mac %d.%d phy %d.%d, dev->name, DEBUG ip_conntrack_irc: max_dcc_channels must be a positive integer DEBUG 5 GHz radio %d.%d 2 GHz radio %d.%d, DEBUG ip_conntrack_irc: ERROR registering port %d, DEBUG radio %d.%d, ah->ah_analog5GhzRev >> 4, DEBUG ip_nat_h323: ip_nat_mangle_tcp_packet DEBUG radio %d.%d, ah->ah_analog5GhzRev >> 4, DEBUG ip_nat_h323: ip_nat_mangle_udp_packet DEBUG %s: Use hw queue %u for %s traffic, DEBUG ip_nat_h323: out of expectations DEBUG %s: Use hw queue %u for CAB traffic, dev->name, DEBUG ip_nat_h323: out of RTP ports DEBUG %s: Use hw queue %u for beacons, dev->name, DEBUG ip_nat_h323: out of TCP ports DEBUG Could not find Board Configuration Data DEBUG ip_nat_q931: out of TCP ports DEBUG Could not find Radio Configuration data DEBUG ip_nat_ras: out of TCP ports DEBUG ath_ahb: No devices found, driver not installed. DEBUG ip_nat_q931: out of TCP ports DEBUG _fmt, __VA_ARGS__ DEBUG ip_conntrack_core: Frag of proto %u., DEBUG _fmt, __VA_ARGS__ DEBUG Broadcast packet! DEBUG xlr8NatIpFinishOutput: Err.. skb2 == NULL ! DEBUG Should bcast: %u.%u.%u.%u->%u.%u.%u.%u (sk=%p, ptype=%u), DEBUG xlr8NatSoftCtxEnqueue: Calling xlr8NatIpFinishOutput () .., status DEBUG ip_conntrack version %s (%u buckets, %d max) DEBUG xlr8NatSoftCtxEnqueue: xlr8NatIpFinishOutput () returned [%d], status DEBUG ERROR registering port %d, DEBUG icmpExceptionHandler: Exception! DEBUG netfilter PSD loaded - (c) astaro AG DEBUG fragExceptionHandler: Exception! DEBUG netfilter PSD unloaded - (c) astaro AG DEBUG algExceptionHandler: Exception! DEBUG %s , SELF DEBUG dnsExceptionHandler: Exception! DEBUG %s , LAN DEBUG ipsecExceptionHandler: Exception! DEBUG %s , WAN DEBUG ESP Packet Src:%x Dest:%x Sport:%d dport:%d secure:%d spi:%d isr:%p, DEBUG TRUNCATED DEBUG xlr8NatConntrackPreHook: We found the valid context, DEBUG SRC=%u.%u.%u.%u DST=%u.%u.%u.%u , DEBUG xlr8NatConntrackPreHook: Not a secured packet. DEBUG LEN=%u TOS=0x%02X PREC=0x%02X TTL=%u ID=%u , DEBUG xlr8NatConntrackPreHook: isr=[%p], pIsr DEBUG FRAG:%u , ntohs(ih->frag_off) & IP_OFFSET DEBUG xlr8NatConntrackPreHook: secure=[%d], secure DEBUG TRUNCATED DEBUG Context found for ESP %p,pFlowEntry->post.pIsr[0] DEBUG PROTO=TCP DEBUG xlr8NatConntrackPreHook: New connection. DEBUG INCOMPLETE [%u bytes] , DEBUG xlr8NatConntrackPostHook: postSecure=[%d] postIsr=[%p %p], DEBUG SPT=%u DPT=%u , DEBUG proto %d spi %d <-------> proto %d spi %d,pPktInfo->proto,pPktInfo->spi, DEBUG SEQ=%u ACK=%u , DEBUG IPSEC_INF Clock skew detected DEBUG WINDOW=%u , ntohs(th->window) DEBUG IPSEC_ERR [%s:%d]: Max (%d) No of SA Limit reached, DEBUG
Unified Services Router User Manual 184 RES=0x%02x , (u8)(ntohl(tcp_flag_word(th) & TCP_RESERVED_BITS) >> 22) DEBUG IPSEC_ERR [%s:%d]: Max (%d) No of SA Limit reached, DEBUG URGP=%u , ntohs(th->urg_ptr) DEBUG IPSEC_ERR [%s:%d]: time(secs): %u DEBUG TRUNCATED DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG %02X, op[i] DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG PROTO=UDP DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG INCOMPLETE [%u bytes] , DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG SPT=%u DPT=%u LEN=%u , DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG SPT=%u DPT=%u LEN=%u , DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG PROTO=ICMP DEBUG unknown oid '%s', varName DEBUG INCOMPLETE [%u bytes] , DEBUG could not find oid pointer for '%s', varName DEBUG TYPE=%u CODE=%u , ich->type, ich->code DEBUG unRegistering ipsecMib ..... DEBUG INCOMPLETE [%u bytes] , DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG ID=%u SEQ=%u , DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG PARAMETER=%u , DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG GATEWAY=%u.%u.%u.%u , DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG MTU=%u , ntohs(ich->un.frag.mtu) DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG PROTO=AH DEBUG ERROR: Failed to add entry to ipsec sa table DEBUG INCOMPLETE [%u bytes] , DEBUG unknown oid '%s', varName DEBUG SPI=0x%x , ntohl(ah->spi) DEBUG could not find oid pointer for '%s', varName DEBUG PROTO=ESP DEBUG unRegistering ipsecMib ..... DEBUG INCOMPLETE [%u bytes] , DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG SPI=0x%x , ntohl(eh->spi) DEBUG %02x, *p DEBUG PROTO=%u , ih->protocol DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG UID=%u , skb->sk->sk_socket->file->f_uid DEBUG %02x, *p DEBUG <%d>%sIN=%s OUT=%s , loginfo->u.log.level, DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG level_string DEBUG %02x, *p DEBUG %sIN=%s OUT=%s , DEBUG . %u.%u.%u.%u, NIPQUAD(trt->rt_dst) DEBUG %s , prefix == NULL ? loginfo->prefix : prefix DEBUG %02x, *p DEBUG IN= DEBUG unable to register vipsec kernel comp to UMI DEBUG OUT= DEBUG unregistering VIPSECK from UMI .... DEBUG PHYSIN=%s , physindev->name DEBUG in vipsecKIoctlHandler cmd - %d, cmd DEBUG PHYSOUT=%s , physoutdev->name DEBUG %s: Error. DST Refcount value less than 1 (%d), DEBUG MAC= DEBUG for %s DEVICE refcnt: %d ,pDst->dev->name, DEBUG
Unified Services Router User Manual 185 %02x%c, *p, DEBUG %s: Got Null m:%p *m:%p sa:%p *sa:%p,__func__,ppBufMgr, DEBUG NAT: no longer support implicit source local NAT DEBUG %s Got Deleted SA:%p state:%d,__func__,pIpsecInfo,pIpsecInfo->state DEBUG NAT: packet src %u.%u.%u.%u -> dst %u.%u.%u.%u, DEBUG %s: %s: fmt, __FILE__, __FUNCTION__ , ## args) INFO SNAT: multiple ranges no longer supported DEBUG %s: %s: fmt, __FILE__, __FUNCTION__ , ## args) INFO format,##args) DEBUG ipt_TIME: format, ## args) INFO version DEBUG IPT_ACCOUNT_NAME : checkentry() wrong parameters (not equals existing table parameters). INFO offset_before=%d, offset_after=%d, correction_pos=%u, x->offset_before, x->offset_after, x->correction_pos DEBUG IPT_ACCOUNT_NAME : checkentry() too big netmask. INFO ip_ct_h323: DEBUG IPT_ACCOUNT_NAME : checkentry() failed to allocate %zu for new table %s., sizeof(struct t_ipt_account_table), info->name INFO ip_ct_h323: incomplete TPKT (fragmented?) DEBUG IPT_ACCOUNT_NAME : checkentry() wrong network/netmask. INFO ip_ct_h245: decoding error: %s, DEBUG account: Wrong netmask given by netmask parameter (%i). Valid is 32 to 0., netmask INFO ip_ct_h245: packet dropped DEBUG IPT_ACCOUNT_NAME : checkentry() failed to create procfs entry. INFO ip_ct_q931: decoding error: %s, DEBUG IPT_ACCOUNT_NAME : checkentry() failed to register match. INFO ip_ct_q931: packet dropped DEBUG failed to create procfs entry . INFO ip_ct_ras: decoding error: %s, DEBUG MPPE/MPPC encryption/compression module registered INFO ip_ct_ras: packet dropped DEBUG MPPE/MPPC encryption/compression module unregistered INFO ERROR registering port %d, DEBUG PPP generic driver version PPP_VERSION INFO ERROR registering port %d, DEBUG MPPE/MPPC encryption/compression module registered INFO ipt_connlimit [%d]: src=%u.%u.%u.%u:%d dst=%u.%u.%u.%u:%d %s, DEBUG MPPE/MPPC encryption/compression module unregistered INFO ipt_connlimit [%d]: src=%u.%u.%u.%u:%d dst=%u.%u.%u.%u:%d new, DEBUG PPP generic driver version PPP_VERSION INFO ipt_connlimit: Oops: invalid ct state ? DEBUG PPPoL2TP kernel driver, %s, INFO ipt_connlimit: Hmm, kmalloc failed :-( DEBUG PPPoL2TP kernel driver, %s, INFO ipt_connlimit: src=%u.%u.%u.%u mask=%u.%u.%u.%u DEBUG PPPoL2TP kernel driver, %s, INFO _lvl PPPOL2TP: _fmt, ##args DEBUG failed to create procfs entry . INFO %02X, ptr[length] DEBUG proc dir not created .. INFO %02X, ((unsigned char *) m->msg_iov[i].iov_base)[j] DEBUG Initialzing Product Data modules INFO %02X, skb->data[i] DEBUG De initializing by \ INFO _lvl PPPOL2TP: _fmt, ##args DEBUG kernel UMI module loaded INFO %02X, ptr[length] DEBUG kernel UMI module unloaded INFO
Unified Services Router User Manual 186 %02X, ((unsigned char *) m->msg_iov[i].iov_base)[j] DEBUG Loading bridge module INFO %02X, skb->data[i] DEBUG Unloading bridge module INFO _lvl PPPOL2TP: _fmt, ##args DEBUG unsupported command %d, cmd INFO %02X, ptr[length] DEBUG Loading ifDev module INFO %02X, ((unsigned char *) m->msg_iov[i].iov_base)[j] DEBUG Unloading ifDev module INFO %02X, skb->data[i] DEBUG ERROR#%d in alloc_chrdev_region, result INFO KERN_EMERG THE value read is %d,value*/ DEBUG ERROR#%d in cdev_add, result INFO KERN_EMERG Factory Reset button is pressed DEBUG using bcm switch %s, bcmswitch INFO KERN_EMERG Returing error in INTR registration DEBUG privlegedID %d wanporttNo: %d, privlegedID,wanportNo INFO KERN_EMERG Initialzing Factory defaults modules DEBUG Loading mii INFO Failed to allocate memory for pSipListNode DEBUG Unloading mii INFO SIPALG: Memeory allocation failed for pSipNodeEntryTbl DEBUG %s: Version 0.1 INFO pkt-err %s, pktInfo.error DEBUG %s: driver unloaded, dev_info INFO pkt-err %s, pktInfo.error DEBUG wlan: %s backend registered, be->iab_name INFO pkt-err %s, pktInfo.error DEBUG wlan: %s backend unregistered, INFO %s Len=%d, msg, len DEBUG wlan: %s acl policy registered, iac->iac_name INFO %02x , ((uint8_t *) ptr)[i] DEBUG wlan: %s acl policy unregistered, iac->iac_name INFO End DEBUG %s, tmpbuf INFO CVM_MOD_EXP_BASE MISMATCH cmd=%x base=%x, cmd, DEBUG VLAN2 INFO op->sizeofptr = %ld, op->sizeofptr DEBUG VLAN3 INFO opcode cmd = %x, cmd DEBUG VLAN4 <%d %d>, INFO modexp opcode received DEBUG %s: %s, dev_info, version INFO Memory Allocation failed DEBUG %s: driver unloaded, dev_info INFO modexpcrt opcode received DEBUG %s, buf INFO kmalloc failed DEBUG %s: %s (, dev_info, ath_hal_version INFO kmalloc failed DEBUG %s: driver unloaded, dev_info INFO kmalloc failed DEBUG %s: %s: mem=0x%lx, irq=%d hw_base=0x%p, INFO kmalloc failed DEBUG %s: %s, dev_info, version INFO kmalloc Failed DEBUG %s: driver unloaded, dev_info INFO kmalloc failed DEBUG %s: %s: mem=0x%lx, irq=%d, INFO unknown cyrpto ioctl cmd received %x, cmd DEBUG %s: %s: mem=0x%lx, irq=%d, INFO register_chrdev returned ZERO DEBUG %s: %s, dev_info, version INFO const char *descr, krb5_keyblock *k) { DEBUG %s: driver unloaded, dev_info INFO F password, &pdata DEBUG %s, buf INFO test key, key DEBUG %s: %s (, dev_info, ath_hal_version INFO pre-hashed key, key DEBUG %s: driver unloaded, dev_info INFO const char *descr, krb5_keyblock *k) { DEBUG %s: driver unloaded, dev_info INFO AES 128-bit key, &key DEBUG %s: Version 2.0.0 INFO
Unified Services Router User Manual 187 const char *descr, krb5_keyblock *k) { DEBUG %s: driver unloaded, dev_info INFO test key, key DEBUG %s: driver unloaded, dev_info INFO pre-hashed key, key DEBUG wlan: %s backend registered, be->iab_name INFO const char *descr, krb5_keyblock *k) { DEBUG wlan: %s backend unregistered, INFO 128-bit AES key,&dk DEBUG wlan: %s acl policy registered, iac->iac_name INFO 256-bit AES key, &dk DEBUG wlan: %s acl policy unregistered, iac->iac_name INFO WARNING: DEBUG %s: %s, dev_info, version INFO bwMonMultipathNxtHopSelect:: checking rates DEBUG %s: driver unloaded, dev_info INFO hop :%d dev:%s usableBwLimit = %d currBwShare = %d lastHopSelected = %d weightedHopPrefer = %d , DEBUG %s: %s (, dev_info, ath_hal_version INFO 1. selecting hop: %d lastHopSelected = %d , selHop, lastHopSelected DEBUG %s: driver unloaded, dev_info INFO 4. hop :%d dev:%s usableBwLimit = %d currBwShare = %d lastHopSelected = %d weightedHopPrefer = %d , DEBUG %s: %s: mem=0x%lx, irq=%d, INFO 2. selecting hop: %d lastHopSelected = %d , selHop, lastHopSelected DEBUG %s: %s, dev_info, version INFO 3. selecting hop: %d lastHopSelected = %d , selHop, lastHopSelected DEBUG %s: driver unloaded, dev_info INFO bwMonitor multipath selection enabled DEBUG ath_pci: switching rfkill capability %s, INFO bwMonitor multipath selection disabled DEBUG Unknown autocreate mode: %s, INFO weightedHopPrefer set to %d ,weightedHopPrefer DEBUG %s: %s: mem=0x%lx, irq=%d, INFO bwMonitor sysctl registration failed DEBUG %s: %s, dev_info, version INFO bwMonitor sysctl registered DEBUG %s: driver unloaded, dev_info INFO bwMonitor sysctl not registered DEBUG %s: %s, dev_info, version INFO Unregistered bwMonitor sysctl DEBUG %s: unloaded, dev_info INFO CONFIG_SYSCTL enabled ... DEBUG %s: %s, dev_info, version INFO Initialized bandwidth monitor ... DEBUG %s: unloaded, dev_info INFO Removed bandwidth monitor ... DEBUG %s: %s, dev_info, version INFO Oops.. AES_GCM_encrypt failed (keylen:%u),key->cvm_keylen DEBUG %s: unloaded, dev_info INFO Oops.. AES_GCM_decrypt failed (keylen:%u),key->cvm_keylen DEBUG failed to create procfs entry . INFO %s, msg DEBUG ICMP: %u.%u.%u.%u: INFO %02x%s, data[i], DEBUG ICMP: %u.%u.%u.%u: Source INFO Failed to set AES encrypt key DEBUG Wrong address mask %u.%u.%u.%u from INFO Failed to set AES encrypt key DEBUG Redirect from %u.%u.%u.%u on %s about INFO AES %s Encrypt Test Duration: %d:%d, hard ? Hard : Soft, DEBUG IP: routing cache hash table of %u buckets, %ldKbytes, INFO Failed to set AES encrypt key DEBUG source route option %u.%u.%u.%u -> %u.%u.%u.%u, INFO Failed to set AES encrypt key DEBUG ICMP: %u.%u.%u.%u: INFO AES %s Decrypt Test Duration: %d:%d, hard ? Hard : Soft, DEBUG ICMP: %u.%u.%u.%u: Source INFO Failed to set AES encrypt key DEBUG Wrong address mask %u.%u.%u.%u from INFO
Unified Services Router User Manual 188 Failed to set AES encrypt key DEBUG Redirect from %u.%u.%u.%u on %s about INFO Failed to set AES encrypt key DEBUG IP: routing cache hash table of %u buckets, %ldKbytes, INFO Failed to set AES encrypt key DEBUG source route option %u.%u.%u.%u -> %u.%u.%u.%u, INFO Failed to set DES encrypt key[%d], i DEBUG Wrong address mask %u.%u.%u.%u from INFO Failed to set DES decrypt key[%d], i DEBUG Redirect from %u.%u.%u.%u on %s about INFO Failed to set DES encrypt key[%d], i DEBUG source route option INFO Failed to set DES decrypt key[%d], i DEBUG ICMP: %u.%u.%u.%u: INFO Failed to set DES encrypt key DEBUG ICMP: %u.%u.%u.%u: Source INFO Failed to set DES decrypt key DEBUG Wrong address mask %u.%u.%u.%u from INFO Failed to set DES encrypt key DEBUG Redirect from %u.%u.%u.%u on %s about INFO Failed to set DES decrypt key DEBUG IP: routing cache hash table of %u buckets, %ldKbytes, INFO AES Software Test: DEBUG source route option %u.%u.%u.%u -> %u.%u.%u.%u, INFO AES Software Test %s, aesSoftTest(0) ? Failed : Passed DEBUG IPsec: device unregistering: %s, dev->name INFO AES Hardware Test: DEBUG IPsec: device down: %s, dev->name INFO AES Hardware Test %s, aesHardTest(0) ? Failed : Passed DEBUG mark: only supports 32bit mark WARNING 3DES Software Test: DEBUG ipt_time: invalid argument WARNING 3DES Software Test %s, des3SoftTest(0) ? Failed : Passed DEBUG ipt_time: IPT_DAY didn't matched WARNING 3DES Hardware Test: DEBUG ./Logs_kernel.txt:45:KERN_WARNING WARNING 3DES Hardware Test %s, des3HardTest(0) ? Failed : Passed DEBUG ./Logs_kernel.txt:59:KERN_WARNING WARNING DES Software Test: DEBUG ipt_LOG: not logging via system console WARNING DES Software Test %s, desSoftTest(0) ? Failed : Passed DEBUG %s: wrong options length: %u, fname, opt_len WARNING DES Hardware Test: DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING DES Hardware Test %s, desHardTest(0) ? Failed : Passed DEBUG %s: wrong options length: %u, WARNING SHA Software Test: DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING SHA Software Test %s, shaSoftTest(0) ? Failed : Passed DEBUG %s: don't know what to do: o[5]=%02x, WARNING SHA Hardware Test: DEBUG %s: wrong options length: %u, fname, opt_len WARNING SHA Hardware Test %s, shaHardTest(0) ? Failed : Passed DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING MD5 Software Test: DEBUG %s: wrong options length: %u, WARNING MD5 Software Test %s, md5SoftTest(0) ? Failed : Passed DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, WARNING MD5 Hardware Test: DEBUG %s: don't know what to do: o[5]=%02x, WARNING MD5 Hardware Test %s, DEBUG *** New port %d ***, ntohs(expinfo- WARNIN
Unified Services Router User Manual 189 md5HardTest(0) ? Failed : Passed >natport) G AES Software Test: %d iterations, iter DEBUG ** skb len %d, dlen %d,(*pskb)->len, WARNING AES Software Test Duration: %d:%d, DEBUG ********** Non linear skb WARNING AES Hardware Test: %d iterations, iter DEBUG End of sdp %p, nexthdr WARNING AES Hardware Test Duration: %d:%d, DEBUG %s: unknown pairwise cipher %d, WARNING 3DES Software Test: %d iterations, iter DEBUG %s: unknown group cipher %d, WARNING 3DES Software Test Duration: %d:%d, DEBUG %s: unknown SIOCSIWAUTH flag %d, WARNING 3DES Hardware Test: %d iterations, iter DEBUG %s: unknown SIOCGIWAUTH flag %d, WARNING 3DES Hardware Test Duration: %d:%d, DEBUG %s: unknown algorithm %d, WARNING DES Software Test: %d iterations, iter DEBUG %s: key size %d is too large, WARNING DES Software Test Duration: %d:%d, DEBUG try_module_get failed \ WARNING DES Hardware Test: %d iterations, iter DEBUG %s: request_irq failed, dev->name WARNING DES Hardware Test Duration: %d:%d, DEBUG try_module_get failed WARNING SHA Software Test: %d iterations, iter DEBUG try_module_get failed \ WARNING SHA Software Test Duration: %d:%d, DEBUG %s: unknown pairwise cipher %d, WARNING SHA Hardware Test: %d iterations, iter DEBUG %s: unknown group cipher %d, WARNING SHA Hardware Test Duration: %d:%d, DEBUG %s: unknown SIOCSIWAUTH flag %d, WARNING MD5 Software Test: %d iterations, iter DEBUG %s: unknown SIOCGIWAUTH flag %d, WARNING MD5 Software Test Duration: %d:%d, DEBUG %s: unknown algorithm %d, WARNING MD5 Hardware Test: %d iterations, iter DEBUG %s: key size %d is too large, WARNING MD5 Hardware Test Duration: %d:%d, DEBUG unable to load %s, scan_modnames[mode] WARNING ./pnac/src/pnac/linux/kernel/xcalibur.c:209:#define DEBUG_PRINTK printk DEBUG Failed to mkdir /proc/net/madwifi WARNING bcmDeviceInit: registration failed DEBUG try_module_get failed WARNING bcmDeviceInit: pCdev Add failed DEBUG %s: request_irq failed, dev->name WARNING REG Size == 8 Bit DEBUG too many virtual ap's (already got %d), sc->sc_nvaps WARNING Value = %x ::: At Page = %x : Addr = %x DEBUG %s: request_irq failed, dev->name WARNING REG Size == 16 Bit DEBUG rix %u (%u) bad ratekbps %u mode %u, WARNING Value = %x ::: At Page = %x : Addr = %x DEBUG cix %u (%u) bad ratekbps %u mode %u, WARNING REG Size == 32 Bit DEBUG %s: no rates for %s?, WARNING Value = %x ::: At Page = %x : Addr = DEBUG no rates yet! mode %u, sc- WARNIN
Unified Services Router User Manual 190 %x >sc_curmode G REG Size == 64 Bit DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING REG Size is not in 8/16/32/64 DEBUG dst cache overflow WARNING Written Value = %x ::: At Page = %x : Addr = %x DEBUG Neighbour table overflow. WARNING bcm_ioctl :Unknown Ioctl Case : DEBUG host %u.%u.%u.%u/if%d ignores WARNING =========Register Dump for Port Number # %d=========,port DEBUG martian destination %u.%u.%u.%u from WARNING %s : Read Status=%s data=%#x,regName[j], DEBUG martian source %u.%u.%u.%u from WARNING %s : Read Status=%s data=%#x,regName[j], DEBUG ll header: WARNING powerDeviceInit: device registration failed DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING powerDeviceInit: adding device failed DEBUG dst cache overflow WARNING %s: Error: Big jump in pn number. TID=%d, from %x %x to %x %x. DEBUG Neighbour table overflow. WARNING %s: The MIC is corrupted. Drop this frame., __func__ DEBUG host %u.%u.%u.%u/if%d ignores WARNING %s: The MIC is OK. Still use this frame and update PN., __func__ DEBUG martian destination %u.%u.%u.%u from WARNING ADDBA send failed: recipient is not a 11n node DEBUG martian source %u.%u.%u.%u from WARNING Cannot Set Rate: %x, value DEBUG ll header: WARNING Getting Rate Series: %x,vap->iv_fixed_rate.series DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING Getting Retry Series: %x,vap->iv_fixed_rate.retries DEBUG dst cache overflow WARNING IC Name: %s,ic->ic_dev->name DEBUG Neighbour table overflow. WARNING usage: rtparams rt_idx <0|1> per <0..100> probe_intval <0..100> DEBUG host %u.%u.%u.%u/if%d ignores WARNING usage: acparams ac <0|3> RTS <0|1> aggr scaling <0..4> min mbps <0..250> DEBUG martian source %u.%u.%u.%u from WARNING usage: hbrparams ac <2> enable <0|1> per_low <0..50> DEBUG ll header: WARNING %s(): ADDBA mode is AUTO, __func__ DEBUG martian destination %u.%u.%u.%u from WARNING %s(): Invalid TID value, __func__ DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING %s(): ADDBA mode is AUTO, __func__ DEBUG dst cache overflow WARNING %s(): Invalid TID value, __func__ DEBUG Neighbour table overflow. WARNING %s(): Invalid TID value, __func__ DEBUG host %u.%u.%u.%u/if%d ignores WARNING Addba status IDLE DEBUG martian destination %u.%u.%u.%u from WARNING %s(): ADDBA mode is AUTO, __func__ DEBUG martian source %u.%u.%u.%u from WARNING %s(): Invalid TID value, __func__ DEBUG ll header: WARNING
Unified Services Router User Manual 191 Error in ADD- no node available DEBUG Unable to create ip_set_list ERROR %s(): Channel capabilities do not match, chan flags 0x%x, DEBUG Unable to create ip_set_hash ERROR %s: cannot map channel to mode; freq %u flags 0x%x, DEBUG ip_conntrack_in: Frag of proto %u (hook=%u), ERROR ic_get_currentCountry not initialized yet DEBUG Unable to register netfilter socket option ERROR Country ie is %c%c%c, DEBUG Unable to create ip_conntrack_hash ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_conntrack slab cache ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_expect slab cache ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_set_iptreeb slab cache ERROR %s: wrong state transition from %d to %d, DEBUG Unable to create ip_set_iptreed slab cache ERROR %s: wrong state transition from %d to %d, DEBUG %s: cannot allocate space for %scompressor, fname, ERROR %s: wrong state transition from %d to %d, DEBUG %s: cannot allocate space for MPPC history, ERROR ieee80211_deliver_l2uf: no buf available DEBUG %s: cannot allocate space for MPPC history, ERROR %s: %s, vap->iv_dev->name, buf /* NB: no */ DEBUG %s: cannot load ARC4 module, fname ERROR %s: [%s] %s, vap->iv_dev->name, DEBUG %s: cannot load SHA1 module, fname ERROR %s: [%s] %s, vap->iv_dev->name, ether_sprintf(mac), buf DEBUG %s: CryptoAPI SHA1 digest size too small, fname ERROR [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG %s: cannot allocate space for SHA1 digest, fname ERROR [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG %s%d: trying to write outside history ERROR [%s:%s] discard %s information element, %s, DEBUG %s%d: trying to write outside history ERROR [%s:%s] discard information element, %s, DEBUG %s%d: trying to write outside history ERROR [%s:%s] discard %s frame, %s, vap->iv_dev->name, DEBUG %s%d: too big uncompressed packet: %d, ERROR [%s:%s] discard frame, %s, vap->iv_dev->name, DEBUG %s%d: encryption negotiated but not an ERROR HBR list dumpNode\tAddress\t\t\tState\tTrigger\tBlock DEBUG %s%d: error - not an MPPC or MPPE frame ERROR Nodes informationAddress\t\t\tBlock\t\tDroped VI frames DEBUG Kernel doesn't provide ARC4 and/or SHA1 algorithms ERROR %d\t %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x\t%s\t%s\t%s, DEBUG PPP: not interface or channel?? ERROR %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x\t%s\t\t%d, DEBUG PPP: no memory (VJ compressor) ERROR [%d]\tFunction\t%s, j, ni->node_trace[i].funcp DEBUG failed to register PPP device (%d), err ERROR [%d]\tMacAddr\t%s, j, DEBUG PPP: no memory (VJ comp pkt) ERROR [%d]\tDescp\t\t%s, j, ni->node_trace[i].descp DEBUG PPP: no memory (comp pkt) ERROR [%d]\tValue\t\t%llu(0x%llx), j, ni->node_trace[i].value, DEBUG ppp: compressor dropped pkt ERROR ifmedia_add: null ifm DEBUG PPP: no memory (fragment) ERROR
Unified Services Router User Manual 192 Adding entry for DEBUG PPP: VJ uncompressed error ERROR ifmedia_set: no match for 0x%x/0x%x, DEBUG ppp_decompress_frame: no memory ERROR ifmedia_set: target DEBUG ppp_mp_reconstruct bad seq %u < %u, ERROR ifmedia_set: setting to DEBUG PPP: couldn't register device %s (%d), ERROR ifmedia_ioctl: switching %s to , dev->name DEBUG ppp: destroying ppp struct %p but dead=%d ERROR ifmedia_match: multiple match for DEBUG ppp: destroying undead channel %p !, ERROR <unknown type> DEBUG PPP: removing module but units remain! ERROR desc->ifmt_string DEBUG PPP: failed to unregister PPP device ERROR mode %s, desc->ifmt_string DEBUG %s: cannot allocate space for %scompressor, fname, ERROR <unknown subtype> DEBUG %s: cannot allocate space for MPPC history, ERROR %s, desc->ifmt_string DEBUG %s: cannot allocate space for MPPC history, ERROR %s%s, seen_option++ ? , : , DEBUG %s: cannot load ARC4 module, fname ERROR %s%s, seen_option++ ? , : , DEBUG %s: cannot load SHA1 module, fname ERROR %s, seen_option ? > : DEBUG %s: CryptoAPI SHA1 digest size too small, fname ERROR %s: %s, dev->name, buf DEBUG %s: cannot allocate space for SHA1 digest, fname ERROR %s: no memory for sysctl table!, __func__ DEBUG %s%d: trying to write outside history ERROR %s: failed to register sysctls!, vap->iv_dev->name DEBUG %s%d: trying to write outside history ERROR Atheros HAL assertion failure: %s: line %u: %s, DEBUG %s%d: trying to write outside history ERROR ath_hal: logging to %s %s, ath_hal_logfile, DEBUG %s%d: too big uncompressed packet: %d, ERROR ath_hal: logging disabled DEBUG %s%d: encryption negotiated but not an ERROR %s%s, sep, ath_hal_buildopts[i] DEBUG %s%d: error - not an MPPC or MPPE frame ERROR ath_pci: No devices found, driver not installed. DEBUG Kernel doesn't provide ARC4 and/or SHA1 algorithms ERROR ---:%d pri:%d qd:%u ad:%u sd:%u tot:%u amp:%d %02x:%02x:%02x, DEBUG PPP: not interface or channel?? ERROR SC Pushbutton Notify on %s::%s,dev->name,vap->iv_dev->name DEBUG PPP: no memory (VJ compressor) ERROR Could not find Board Configuration Data DEBUG failed to register PPP device (%d), err ERROR Could not find Radio Configuration data DEBUG PPP: no memory (comp pkt) ERROR %s: No device, __func__ DEBUG ppp: compressor dropped pkt ERROR ath_ahb: No devices found, driver not installed. DEBUG PPP: no memory (VJ comp pkt) ERROR PKTLOG_TAG %s:proc_dointvec failed, __FUNCTION__ DEBUG PPP: no memory (comp pkt) ERROR PKTLOG_TAG %s:proc_dointvec failed, __FUNCTION__ DEBUG PPP: no memory (fragment) ERROR %s: failed to register sysctls!, proc_name DEBUG PPP: VJ uncompressed error ERROR PKTLOG_TAG %s: proc_mkdir failed, __FUNCTION__ DEBUG ppp_decompress_frame: no memory ERROR PKTLOG_TAG %s: pktlog_attach failed for %s, DEBUG ppp_mp_reconstruct bad seq %u < %u, ERROR
Unified Services Router User Manual 193 PKTLOG_TAG %s:allocation failed for pl_info, __FUNCTION__ DEBUG PPP: couldn't register device %s (%d), ERROR PKTLOG_TAG %s:allocation failed for pl_info, __FUNCTION__ DEBUG ppp: destroying ppp struct %p but dead=%d ERROR PKTLOG_TAG %s: create_proc_entry failed for %s, DEBUG ppp: destroying undead channel %p !, ERROR PKTLOG_TAG %s: sysctl register failed for %s, DEBUG PPP: removing module but units remain! ERROR PKTLOG_TAG %s: page fault out of range, __FUNCTION__ DEBUG PPP: failed to unregister PPP device ERROR PKTLOG_TAG %s: page fault out of range, __FUNCTION__ DEBUG JBD: bad block at offset %u, ERROR PKTLOG_TAG %s: Log buffer unavailable, __FUNCTION__ DEBUG JBD: corrupted journal superblock ERROR PKTLOG_TAG DEBUG JBD: bad block at offset %u, ERROR Logging should be disabled before changing bufer size DEBUG JBD: Failed to read block at offset %u, ERROR %s:allocation failed for pl_info, __func__ DEBUG JBD: error %d scanning journal, err ERROR %s: Unable to allocate buffer, __func__ DEBUG JBD: IO error %d recovering block ERROR %s:allocation failed for pl_info, __func__ DEBUG ./Logs_kernel.txt:303:KERN_ERR ERROR %s: Unable to allocate buffer, __func__ DEBUG ./Logs_kernel.txt:304:KERN_ERR ERROR Atheros HAL assertion failure: %s: line %u: %s, DEBUG JBD: recovery pass %d ended at ERROR ath_hal: logging to %s %s, ath_hal_logfile, DEBUG %s: %s:%d: BAD SESSION MAGIC \ ERROR ath_hal: logging disabled DEBUG %s: %s:%d: BAD TUNNEL MAGIC \ ERROR %s%s, sep, ath_hal_buildopts[i] DEBUG msg->msg_namelen wrong, %d, msg->msg_namelen ERROR failed to allocate rx descriptors: %d, error DEBUG addr family wrong: %d, usin->sin_family ERROR ath_stoprecv: rx queue %p, link %p, DEBUG udp addr=%x/%hu, usin->sin_addr.s_addr, usin->sin_port ERROR no mpdu (%s), __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR Reset rx chain mask. Do internal reset. (%s), __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR OS_CANCEL_TIMER failed!! DEBUG socki_lookup: socket file changed! ERROR %s: unable to allocate channel table, __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR %s: unable to collect channel list from hal; DEBUG %s: %s:%d: BAD SESSION MAGIC \ ERROR %s: cannot map channel to mode; freq %u flags 0x%x, DEBUG %s: %s:%d: BAD TUNNEL MAGIC \ ERROR %s: unable to reset channel %u (%uMhz) DEBUG msg->msg_namelen wrong, %d, msg->msg_namelen ERROR %s: unable to restart recv logic, DEBUG addr family wrong: %d, usin->sin_family ERROR %s: start DFS WAIT period on channel %d, __func__,sc->sc_curchan.channel DEBUG udp addr=%x/%hu, usin->sin_addr.s_addr, usin->sin_port ERROR %s: cancel DFS WAIT period on channel %d, __func__, sc->sc_curchan.channel DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR Non-DFS channel, cancelling previous DFS wait timer channel %d, sc->sc_curchan.channel DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR %s: unable to reset hardware; hal status %u DEBUG socki_lookup: socket file changed! ERROR
Unified Services Router User Manual 194 %s: unable to start recv logic, __func__ DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR %s: unable to start recv logic, __func__ DEBUG %s: %s:%d: BAD SESSION MAGIC \ ERROR %s: unable to reset hardware; hal status %u, DEBUG %s: %s:%d: BAD TUNNEL MAGIC \ ERROR hardware error; reseting DEBUG msg->msg_namelen wrong, %d, msg->msg_namelen ERROR rx FIFO overrun; reseting DEBUG addr family wrong: %d, usin->sin_family ERROR %s: During Wow Sleep and got BMISS, __func__ DEBUG udp addr=%x/%hu, usin->sin_addr.s_addr, usin->sin_port ERROR AC\tRTS \tAggr Scaling\tMin Rate(Kbps)\tHBR \tPER LOW THRESHOLD DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR BE\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR BK\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG socki_lookup: socket file changed! ERROR VI\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG %s: %s:%d: BAD TUNNEL MAGIC ERROR VO\t%s\t\t%d\t%6d\t\t%s\t%d, DEBUG rebootHook: null function pointer ERROR --%d,%p,%lu:0x%x 0x%x 0x%p 0x%x 0x%x 0x%x 0x%x, DEBUG Bad ioctl command ERROR bb state: 0x%08x 0x%08x, bbstate(sc, 4ul), bbstate(sc, 5ul) DEBUG fResetMod: Failed to configure gpio pin ERROR %08x %08x %08x %08x %08x %08x %08x %08x%08x %08x %08x %08x, DEBUG fResetMod: Failed to register interrupt handler ERROR noise floor: (%d, %d) (%d, %d) (%d, %d), DEBUG registering char device failed ERROR %p: %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x, DEBUG unregistering char device failed ERROR --%d,%p,%lu:0x%x 0x%x 0x%p 0x%x 0x%x 0x%x 0x%x, DEBUG proc entry delete failed ERROR %08x %08x %08x %08x %08x %08x %08x %08x%08x %08x %08x %08x, DEBUG proc entry initialization failed ERROR %s: unable to allocate device object., __func__ DEBUG testCompHandler: received %s from %d, (char *)pInBuf, ERROR %s: unable to attach hardware; HAL status %u, DEBUG UMI proto registration failed %d,ret ERROR %s: HAL ABI msmatch; DEBUG AF_UMI registration failed %d,ret ERROR %s: Warning, using only %u entries in %u key cache, DEBUG umi initialization failed %d,ret ERROR unable to setup a beacon xmit queue! DEBUG kernel UMI registration failed! ERROR unable to setup CAB xmit queue! DEBUG ./Logs_kernel.txt:447:KERN_ERR ERROR unable to setup xmit queue for BE traffic! DEBUG ERROR msm not found properly %d, len %d, msm, ERROR %s DFS attach failed, __func__ DEBUG ModExp returned Error ERROR %s: Invalid interface id = %u, __func__, if_id DEBUG ModExp returned Error ERROR %s:grppoll Buf allocation failed ,__func__ DEBUG %s: 0x%p len %u, tag, p, (unsigned int)len ERROR %s: unable to start recv logic, DEBUG %03d:, i ERROR %s: Invalid interface id = %u, __func__, if_id DEBUG %02x, ((unsigned char *)p)[i] ERROR %s: unable to allocate channel table, __func__ DEBUG mic check failed ERROR %s: Tx Antenna Switch. Do internal reset., __func__ DEBUG %s: 0x%p len %u, tag, p, (unsigned int)len ERROR
Unified Services Router User Manual 195 Radar found on channel %d (%d MHz), DEBUG %03d:, i ERROR End of DFS wait period DEBUG %02x, ((unsigned char *)p)[i] ERROR %s error allocating beacon, __func__ DEBUG mic check failed ERROR failed to allocate UAPSD QoS NULL tx descriptors: %d, error DEBUG [%s] Wrong parameters, __func__ ERROR failed to allocate UAPSD QoS NULL wbuf DEBUG [%s] Wrong Key length, __func__ ERROR %s: unable to allocate channel table, __func__ DEBUG [%s] Wrong parameters, __func__ ERROR %s: unable to update h/w beacon queue parameters, DEBUG [%s] Wrong Key length, __func__ ERROR ALREADY ACTIVATED DEBUG [%s] Wrong parameters, __func__ ERROR %s: missed %u consecutive beacons, DEBUG [%s] Wrong Key length, __func__ ERROR %s: busy times: rx_clear=%d, rx_frame=%d, tx_frame=%d, __func__, rx_clear, rx_frame, tx_frame DEBUG [%s] Wrong parameters, __func__ ERROR %s: unable to obtain busy times, __func__ DEBUG [%s] Wrong Key length, __func__ ERROR %s: beacon is officially stuck, DEBUG [%s]: Wrong parameters, __func__ ERROR Busy environment detected DEBUG [%s] Wrong Key Length %d, __func__, des_key_len ERROR Inteference detected DEBUG [%s] Wrong parameters %d, __func__, des_key_len ERROR rx_clear=%d, rx_frame=%d, tx_frame=%d, DEBUG [%s] Wrong Key Length %d, __func__, des_key_len ERROR %s: resume beacon xmit after %u misses, DEBUG [%s] Wrong parameters, __func__ ERROR %s: stuck beacon; resetting (bmiss count %u), DEBUG [%s] Wrong Key Length, __func__ ERROR EMPTY QUEUE DEBUG [%s] Wrong parameters, __func__ ERROR SWRInfo: seqno %d isswRetry %d retryCnt %d,wh ? (*(u_int16_t *)&wh->i_seq[0]) >> 4 : 0, bf->bf_isswretry,bf->bf_swretries DEBUG [%s] Wrong Key Length, __func__ ERROR Buffer #%08X --> Next#%08X Prev#%08X Last#%08X,bf, TAILQ_NEXT(bf,bf_list), DEBUG [%s] Wrong parameters, __func__ ERROR Stas#%08X flag#%08X Node#%08X, bf->bf_status, bf->bf_flags, bf->bf_node DEBUG [%s] Wrong parameters, __func__ ERROR Descr #%08X --> Next#%08X Data#%08X Ctl0#%08X Ctl1#%08X, bf->bf_daddr, ds->ds_link, ds->ds_data, ds->ds_ctl0, ds->ds_ctl1 DEBUG [%s] Wrong parameters, __func__ ERROR Ctl2#%08X Ctl3#%08X Sta0#%08X Sta1#%08X,ds->ds_hw[0], ds->ds_hw[1], lastds->ds_hw[2], lastds->ds_hw[3] DEBUG [%s] Wrong parameters, __func__ ERROR Error entering wow mode DEBUG device name=%s not found, pReq->ifName ERROR Wakingup due to wow signal DEBUG unable to register KIFDEV to UMI ERROR %s, wowStatus = 0x%x, __func__, wowStatus DEBUG ERROR: %s: Timeout at page %#0x addr %#0x ERROR Pattern added already DEBUG ERROR: %s: Timeout at page %#0x addr %#0x ERROR Error : All the %d pattern are in use. Cannot add a new pattern , DEBUG Invalid IOCTL %#08x, cmd ERROR
Unified Services Router User Manual 196 MAX_NUM_PATTERN Pattern added to entry %d ,i DEBUG %s: unable to register device, dev->name ERROR Remove wake up pattern DEBUG ath_pci: 32-bit DMA not available ERROR mask = %p pat = %p ,maskBytes,patternBytes DEBUG ath_pci: cannot reserve PCI memory region ERROR mask = %x pat = %x ,(u_int32_t)maskBytes, (u_int32_t)patternBytes DEBUG ath_pci: cannot remap PCI memory region) ; ERROR Pattern Removed from entry %d ,i DEBUG ath_pci: no memory for device state ERROR Error : Pattern not found DEBUG %s: unable to register device, dev->name ERROR PPM STATE ILLEGAL %x %x, forcePpmStateCur, afp->forceState DEBUG ath_dev_probe: no memory for device state ERROR FORCE_PPM %4d %6.6x %8.8x %8.8x %8.8x %3.3x %4.4x, DEBUG %s: no memory for device state, __func__ ERROR failed to allocate tx descriptors: %d, error DEBUG kernel MIBCTL registration failed! ERROR failed to allocate beacon descripotrs: %d, error DEBUG Bad ioctl command ERROR failed to allocate UAPSD descripotrs: %d, error DEBUG WpsMod: Failed to configure gpio pin ERROR hal qnum %u out of range, max %u!, DEBUG WpsMod: Failed to register interrupt handler ERROR HAL AC %u out of range, max %zu!, DEBUG registering char device failed ERROR HAL AC %u out of range, max %zu!, DEBUG unregistering char device failed ERROR %s: unable to update hardware queue %u!, DEBUG %s:%d - ERROR: non-NULL node pointer in %p, %p<%s>! ERROR Multicast Q: DEBUG %s:%d - ERROR: non-NULL node pointer in %p, %p<%s>! ERROR %p , buf DEBUG can't alloc name %s, name ERROR buf flags - 0x%08x --------- , buf->bf_flags DEBUG %s: unable to register device, dev->name ERROR buf status - 0x%08x, buf->bf_status DEBUG failed to automatically load module: %s; \ ERROR # frames in aggr - %d, length of aggregate - %d, length of frame - %d, sequence number - %d, tidno - %d, DEBUG Unable to load needed module: %s; no support for \ ERROR isdata: %d isaggr: %d isampdu: %d ht: %d isretried: %d isxretried: %d shpreamble: %d isbar: %d ispspoll: %d aggrburst: %d calcairtime: %d qosnulleosp: %d, DEBUG Module \%s\ is not known, buf ERROR %p: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG Error loading module \%s\, buf ERROR 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG Module \%s\ failed to initialize, buf ERROR 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG ath_pci: 32-bit DMA not available ERROR sc_txq[%d] : , i DEBUG ath_pci: cannot reserve PCI memory region ERROR tid %p pause %d : , tid, tid->paused DEBUG ath_pci: cannot remap PCI memory region) ; ERROR %d: %p , j, tid->tx_buf[j] DEBUG ath_pci: no memory for device state ERROR
Unified Services Router User Manual 197 %p , buf DEBUG %s: unable to attach hardware: '%s' (HAL status %u), ERROR axq_q: DEBUG %s: HAL ABI mismatch; ERROR %s: unable to reset hardware; hal status %u, __func__, status DEBUG %s: failed to allocate descriptors: %d, ERROR ****ASSERTION HIT**** DEBUG %s: unable to setup a beacon xmit queue!, ERROR MacAddr=%s, DEBUG %s: unable to setup CAB xmit queue!, ERROR TxBufIdx=%d, i DEBUG %s: unable to setup xmit queue for %s traffic!, ERROR Tid=%d, tidno DEBUG %s: unable to register device, dev->name ERROR AthBuf=%p, tid->tx_buf[i] DEBUG %s: autocreation of VAP failed: %d, ERROR %s: unable to reset hardware; hal status %u, DEBUG ath_dev_probe: no memory for device state ERROR %s: unable to reset hardware; hal status %u, DEBUG kdot11RogueAPEnable called with NULL argument. ERROR %s: unable to start recv logic, DEBUG kdot11RogueAPEnable: can not add more interfaces ERROR _fmt, __VA_ARGS__ \ DEBUG kdot11RogueAPGetState called with NULL argument. ERROR sample_pri=%d is a multiple of refpri=%d, sample_pri, refpri DEBUG kdot11RogueAPDisable called with NULL argument. ERROR ===========ft->ft_numfilters=%u===========, ft->ft_numfilters DEBUG %s: SKB does not exist., __FUNCTION__ ERROR filter[%d] filterID = %d rf_numpulses=%u; rf->rf_minpri=%u; rf->rf_maxpri=%u; rf->rf_threshold=%u; rf->rf_filterlen=%u; rf->rf_mindur=%u; rf->rf_maxdur=%u,j, rf->rf_pulseid, DEBUG %s: recvd invalid skb ERROR NOL DEBUG unable to register KIFDEV to UMI ERROR WARNING!!! 10 minute CAC period as channel is a weather radar channel DEBUG The system is going to factory defaults........!!! CRITICAL %s disable detects, __func__ DEBUG %s, msg CRITICAL %s enable detects, __func__ DEBUG %02x, *(data + i) CRITICAL %s disable FFT val=0x%x , __func__, val DEBUG Inside crypt_open in driver ###### CRITICAL %s enable FFT val=0x%x , __func__, val DEBUG Inside crypt_release in driver ###### CRITICAL %s debug level now = 0x%x , __func__, dfs_debug_level DEBUG Inside crypt_init module in driver @@@@@@@@ CRITICAL RateTable:%d, maxvalidrate:%d, ratemax:%d, pRc->rateTableSize,k,pRc->rateMaxPhy DEBUG Inside crypt_cleanup module in driver @@@@@@@@ CRITICAL %s: txRate value of 0x%x is bad., __FUNCTION__, txRate DEBUG SKB is null : %p ,skb CRITICAL Valid Rate Table:- DEBUG DST is null : %p ,dst CRITICAL Index:%d, value:%d, code:%x, rate:%d, flag:%x, i, (int)validRateIndex[i], DEBUG DEV is null %p %p ,dev,dst CRITICAL RateTable:%d, maxvalidrate:%d, ratemax:%d, pRc->rateTableSize,k,pRc->rateMaxPhy DEBUG Packet is Fragmented %d,pBufMgr->len CRITICAL
Unified Services Router User Manual 198 Can't allocate memory for ath_vap. DEBUG Marked the packet proto:%d sip:%x dip:%x sport:%d dport:%d spi:%d,isr:%p:%p %p CRITICAL Unable to add an interface for ath_dev. DEBUG SAV CHECK FAILED IN DECRYPTION CRITICAL %s: [%02u] %-7s , tag, ix, ciphers[hk->kv_type] DEBUG FAST PATH Breaks on BUF CHECK CRITICAL %02x, hk->kv_val[i] DEBUG FAST PATH Breaks on DST CHECK CRITICAL mac %02x-%02x-%02x-%02x-%02x-%02x, mac[0], mac[1], mac[2], mac[3], mac[4], mac[5] DEBUG FAST PATH Breaks on MTU %d %d %d,bufMgrLen(pBufMgr),mtu,dst_mtu(pDst->path) CRITICAL mac 00-00-00-00-00-00 DEBUG FAST PATH Breaks on MAX PACKET %d %d,bufMgrLen(pBufMgr),IP_MAX_PACKET CRITICAL %02x, hk->kv_mic[i] DEBUG SAV CHECK FAILED IN ENCRYPTION CRITICAL txmic DEBUG Match Found proto %d spi %d,pPktInfo->proto,pFlowEntry->pre.spi CRITICAL %02x, hk->kv_txmic[i] DEBUG PRE: proto: %u srcip:%u.%u.%u.%u sport :%u dstip: %u.%u.%u.%u dport: %u, CRITICAL Cannot support setting tx and rx keys individually DEBUG POST: proto: %u srcip:%u.%u.%u.%u sport :%u dstip: %u.%u.%u.%u dport: %u, CRITICAL bogus frame type 0x%x (%s), DEBUG Clearing the ISR %p,p CRITICAL ERROR: ieee80211_encap ret NULL DEBUG PROTO:%d %u.%u.%u.%u--->%u.%u.%u.%u, CRITICAL ERROR: ath_amsdu_attach not called DEBUG ESP-DONE: %p %p,sav,m CRITICAL %s: no memory for cwm attach, __func__ DEBUG ESP-BAD: %p %p,sav,m CRITICAL %s: error - acw NULL. Possible attach failure, __func__ DEBUG Bug in ip_route_input_slow(). CRITICAL %s: unable to abort tx dma, __func__ DEBUG Bug in ip_route_input_slow(). CRITICAL %s: no memory for ff attach, __func__ DEBUG Bug in ip_route_input \ CRITICAL Failed to initiate PBC based enrolle association DEBUG Bug in ip_route_input_slow(). CRITICAL KERN_EMERG Returing error in INTR registration DEBUG AH: Assigning the secure flags for sav :%p,sav CRITICAL KERN_EMERG Initialzing Wps module DEBUG ESP: Assigning the secure flags for sav :%p skb:%p src:%x dst:%x,sav,skb,ip->ip_src.s_addr,ip->ip_dst.s_addr CRITICAL %s:%d %s, __FILE__, __LINE__, __func__ DEBUG %s Buffer %d mtu %d path mtu %d header %d trailer %d,__func__,bufMgrLen(pBufMgr),mtu,dst_mtu(pDst->path),pDst->header_len,pDst->trailer_len CRITICAL
FCC Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipmentshould be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference, and2) This device must accept any interference received, including interference that may cause undesired operation.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The antennas used for this transmitter must be installed to provide a spectrum distance of at least 20cm from all personsand must not be co-located or operating in conjunction with any other antenna or transmitter.Non-modification StatementUse only the integral antenna supplied by the manufacturer when operating this device. Unauthorized antennas,modifications, or attachments could damage the TI Navigator access point and violate FCC regulations. Any changesor modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate this equipment.Federal Communications Commission (FCC) Compliance Notice: Radio Frequency NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Canadian Department of Communications Industry Canada (IC) NoticeThis Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de la classe Best conforme à la norme NMB-003 et CNR-210 du Canada.Industry Canada StatementThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE: Radiation Exposure StatementThis equipment complies with IC radiation exposure limits set forth for an uncontrolledenvironment. End users must follow the specific operating instructions for satisfying RFexposure compliance. To maintain compliance with IC RF exposure compliance requirements,please follow operation instruction as documented in this manual.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006+A11:2009 Safety of information technology equipment - EN 300 328 V1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive - EN 301 489-17 V1.3.2 (2008-04) and EN 301 489-1 V1.8.1 (2008-04) Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries under the following conditions and/or with the following restrictions: - In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. - This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the enduser should contact the national spectrum authority in France.
Česky [Czech] [D-Link Corporation] tímto prohlašuje, že tento [DSR-500N] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [D-Link Corporation] erklærer herved, at følgende udstyr [DSR-500N] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [D-Link Corporation], dass sich das Gerät [DSR-500N] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [D-Link Corporation] seadme [DSR-500N] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [D-Link Corporation], declares that this [DSR-500N] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [D-Link Corporation] declara que el [DSR-500N] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [D-Link Corporation] ΔΗΛΩΝΕΙ ΟΤΙ [DSR-500N] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [D-Link Corporation] déclare que l'appareil [DSR-500N] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [D-Link Corporation] dichiara che questo [DSR-500N] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [D-Link Corporation] deklarē, ka [DSR-500N] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [D-Link Corporation] deklaruoja, kad šis [DSR-500N] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [D-Link Corporation] dat het toestel [DSR-500N] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [D-Link Corporation], jiddikjara li dan [DSR-500N] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [D-Link Corporation] nyilatkozom, hogy a [DSR-500N] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [D-Link Corporation] oświadcza, że [DSR-500N] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese] [D-Link Corporation] declara que este [DSR-500N]está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [D-Link Corporation] izjavlja, da je ta [DSR-500N] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [D-Link Corporation] týmto vyhlasuje, že [DSR-500N] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [D-Link Corporation] vakuuttaa täten että [DSR-500N] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [D-Link Corporation] att denna [DSR-500N] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Navigation menu