D Link T1130 2.4Ghz/54Mbps Wireless MINI PCI Card User Manual 802 11g Mini PCI manual

D Link Corporation 2.4Ghz/54Mbps Wireless MINI PCI Card 802 11g Mini PCI manual

Users Manual

IEEE 802.11g (draft) Wireless Network Adapter User Manual version 1.0
Manufacturer's Disclaimer Statement The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular purpose of this document. The manufacturer reserves the right to make changes to the content of this document and/or the products associated with it at any time without obligation to notify any person or organization of such changes. In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages. This document contains materials protected by copyright. All rights are reserved. No part of this manual may be reproduced or transmitted in any form, by any means or for any purpose without expressed written consent of its authors. Product names appearing in this document are mentioned for identification purchases only. All trademarks, product names or brand names appearing in this document are registered property of their respective owners.
Driver Installation Step 1: Insert the 802.11g Wireless Network Adapter into your computer. Windows Found New Hardware Wizard will come up. Select the second option and click “Next” to continue.
Step 2: Select the driver to install. Click “Browse” to select the folder where you store the driver files. Click “OK” to continue. Click “Next” to continue.
Step 4: Driver Found Click “Continue Anyway” to continue
Step 3: Driver Installation Driver files are being saved to your Windows system.
Step 4: Driver Installation Complete Click “Finish” to complete the driver setup. The following message will appear as soon as you successfully installed the driver for your IEEE 802.11g wireless network adapter.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one of thefollowing measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device may not causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved bythe party responsible for compliance could void the user's authority tooperate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment. This equipment should be installed and operatedwith minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with anyother antenna or transmitter.
This device is intended only for OEM integrators under the followingconditions: 1) The antenna must be installed such that 20 cm is maintained between theantenna and users.2) The transmitter module may not be co-located with any other transmitteror antenna.3) The Module is approved using the FCC ‘unlicensed modular transmitterapproval’ method. Therefore the module must only be used with the originallyapproved antennas.As long as the 3 conditions above are met, further transmitter testing will notbe required. However, the OEM integrator is still responsible for testingtheir end-product for any additional compliance requirements required withthis module installed (for example, digital device emissions, PC peripheralrequirements, etc.).IMPORTANT NOTE: In the event that these conditions can not be met (forexample certain laptop configurations or co-location with another transmitter),then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integratorwill be responsible for re-evaluating the end product (including the transmitter)and obtaining a separate FCC authorization.End Product LabelingThis transmitter module is authorized only for use in device where the antennamay be installed such that 20 cm may be maintained between the antenna andusers (for example :Wireless AP, Wireless Router ). The final end product mustbe labeled in a visible area with the following: “Contains TX FCC ID:KA2T1130”.Manual Information That Must be IncludedThe OEM integrator has to be aware not to provide information to the end userregarding how to install or remove this RF module in the users manual of theend product which integrate this module.The users manual for OEM integrators must include the following informationin a prominent location “ IMPORTANT NOTE: To comply with FCC RF
exposure compliance requirements, the antenna used for this transmitter mustbe installed to provide a separation distance of at least 20 cm from all personsand must not be co-located or operating in conjunction with any other antennaor transmitter.

Navigation menu