D O Tel DOTH-500 Industrial PDA User Manual 1

D.O.Tel Co., Ltd. Industrial PDA 1

Contents

User Manual

시작하기 전에...1. This user manual may be changed without notice in accordance with improvements to the product or changes in available functions.2. This user manual has been prepared based on information available at the time of publishing and may have technical or editorial errors or omissions.3. The screen and shape of the product in this manual may differ from that of the actual product.4. All the content of this manual is protected by Copyright Law.5. All the rights for the software installed on this product belong to DOTel Co., Ltd. And are protected by Copyright Law.6. Among the content specified in this manual, some functions may not be installed in your PDA (Wireless LAN, Bluetooth)Before starting…FCC NOTICE TO USERS: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user's authority to operate the device.During transmitter operation, in order to meet RF maximum permissible Exposure Safety Guidelines, a minimum distance of 0cm shall be maintained between this device and personnel. This equipment may generate or use frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
Consent Regarding Copyright and Use...1. All the contents in this manual and PDA software are protected by Copyright Law and all the rights belong to DOTel Co., Ltd.2. No part of this manual may be duplicated, renovated or translated into other languages without prior written consent. The act of duplicating, correcting or distributing this manual without permission is a crime punishable in accordance with Copyright Law.3. As to instructions for separate business programs not specified in this manual, and questions about and after service for such programs,please contact the software provider.4. For all other applications or programs installed by the user except the basic program, each software provider should specify contact information required to make inquiries or ask for technical support on the product manual or on the packaging, or enclose a separate manual with contact information.5. DOTel Co., Ltd. Does not provide any warranty for all the software installed once PDAs are shipped out of the factory.6. DOT is a trademark of DOTel Co., Ltd. Protected by law.7. The logos and product names, Microsoft, Windows and Internet Explorer, are trademarks of Microsoft and MS Windows CE software installedon this device is a product officially licensed by Microsoft.8. All the product names and program names used in this manual and the product are company names, symbols, trademarks or registered trademarks of each owner.9. DOTel Co., Ltd. May ask the application providers to provide their software loaded in this product on request of mobile communication providers or for improvement or verification of the products.
Table of Contents1. Important Notices.2. Before Using2.1 Package Contents2.2 Button Layout and Physical Features2.3 Connection to a PC3. Additional Functions3.1 Wireless LAN3.2 Bluetooth4. Problem Solving and Warranty4.1 Problem Solving4.2 Contacting Customer Support4.3 Product Warranty4.4 communication and Product Specifications4.5 Product specifications
1. Important Notices: Proper Usage and Battery Care!!Be sure to carefully read this user manual, as not observing thecautions may cause injury of the user or other persons, or damage to property.The manufacturer and seller do not take any responsibilities for any and all accidents due to not observing the cautions specified in this manual.This product should be used only for the established purpose. Do not use the product for other purposes than those specified in the user manual.If there is an odor of burning or excessive heat from the product while in use, remove the battery and immediately contact the customer service center.Be sure to use the product in a bright place to protect your eyesight, as looking into the LCD screen in a dark place for a long period of time may hurt your eyesight.We recommend you to back up important data in this product often. The seller and manufacturer do not take any responsibility for data loss, even during service or repair of the product. The manufacturer and seller as well as the customer service center do not take any responsibility for data loss.Do not place the product near magnets or magnetic fields. It may cause failure of the product.Use the LCD screen with a stylus pen provided by the manufacturer or a non pointed tool. Otherwise, the LCD may be damaged.Do not handle the product with wet hands as it may cause malfunction of the product and, especially, if the AC adapter is handled with wet hands, there is a risk of electrocution.The film attached on the LCD is a film used to protect the LCD during shipping. If the product is used with the film on, poor touch screen functionmay occur. Be sure to use the product after replacing the film with the LCD protection film separately provided.
1. Important Notices: Proper Usage and Battery Care!!When using USB cable and adapter be careful with the direction of connector insertion If it is inserted incorrectly it may cause a problem with the PDA or PC. Ensure the cable used is in good condition not having bent pins or damaged areas along the cord.Turn off the power of the product in places where use of the product is prohibited. Especially where radio wave interference may occur such as in an airplane or in a hospital. Electromagnetic waves generated by the product not harmful to a human body may cause problems for electronic flight equipment or medical instruments.The product may not operate properly in extreme cold or heat. The proper operating temperature is between -10℃ ~ 50℃. Be especially careful to avoid storing the product in a place in extreme temperatures, or moistareas. This may cause external change or product damage. Store in a cool dry place. In following cases, warranty service will not be provided and repairs may be impossible:- If the product has been disassembled or remodeled by the user;- If the product has fallen into the water or stored in a moist place fora long period of time;- If the product has been dropped from a high place or received excessive external shock.Charge the battery fully for at least 30 minutes or longer before using the product for the first time. The product may not turn on before the battery is charged.There is a risk of explosion if the battery installed is of the incorrect type. When replacing the battery be sure to check that you are using the correct one. Dispose of used batteries according to the instructions.If battery not provided by the manufacturer are used, there is risk of product failure or explosion. Keep the battery away from children or pets to prevent them from biting or sucking the battery. Be careful to prevent metal objects from contacting the charging terminals of the battery as it may cause fire.
1. Important Notices: Proper Usage and Battery Care!!Do not paint or attach stickers to the product, especially if those paints or stickers contain metal ingredients. It may cause buttons not to operate or reception problems.Do not use any power adaptor with this product except the one provided.Provided adaptorModel : KSAFE0500400W1UV-1 / Manufacturer : Kuantech(Shenzhen)Co. Ltd
…………………………………………………………………2.1 Package ContentsBasic ComponentsAdditional Components2. Before usingNoticeNoticeThe specification and components of this product may changeAccording to the situation of the manufacturer.Device Micro USB Cable Cradle Touch Film Stylus PenTwo Standard Batteries A/C Adapter Manual CDLeather case
……………………………………………………………….2.2 Button Layout and Physical FeaturesPart Description and Function2. Before UsingName Description①LCD Touch screen on which information is displayed②Speaker Where the sound is output③ Buttons Function Key④ Battery Switch Switch used to mount or remove the battery⑤Battery Standard capacity battery⑥ Power key Switching the product on/off by pressing and holding this key⑦ Reset key Used to the product to reboot⑧ Battery Charge indicator Displays the status of battery charging and complete⑨ WLAN indicator Displays the status of WLAN links⑩ Stylus pen holder Stylus pen holder⑪ Cradle Insertion Hole Place to insert the cradle for charging and synchronization
……………………………………………………………….2.2 Button Layout and Physical Features2. Before UsingButton FunctionsButton FunctionFunction Key1Function Key2Function Key3To turn on/off the product, pressing and holding the power key for three seconds.To turn on/off the LCD while the device is on, pressing the power key.Used to reset the product to reboot it when a problem has occurred during use.
……………………………………………………………….2.2 Button Layout and Physical FeaturesPower connection and charging2. Before UsingConnect the device to the cradle.1Connect an adapter to the back of the cradle.2While charging, the red LED light will be on.When charging is complete, light will turn green.3Battery charging and using timeStandard BatteryCharging time About 3 hoursStandby time About 500 hoursNoticeNotice- The Charging time is calculated based on using the proper charging cradle.- Charge, talk and standby time may depending on user environment.-Battery life will vary by user service type, environment, battery age.-If user does not use the device, the battery will lose charge. The battery is consumable product.-If battery usage time decreases below standard a new battery should be purchased.-PDA warranty is 1 year. Battery warranty is 6 months.
……………………………………………………………….2.3 To connect with a PCTo install Active Sync2. Before Using1Agree with the license for Microsoft ActiveSync. Select ‘Agree’ and press‘Next’2Enter ‘User Name’ and ‘Organization’and press ‘Next’3Check the disk capacity which can be usedfor installation and change the installationlocation by pressing ‘Change’ or press‘Next’ if you want to install it in the defaultLocation.4In order to connect (synchronize) the PDA with a PC, Microsoft program called ActiveSync is required. For installation, execute ‘Install Program’ and press ‘Next’. At this time the PDA and PC should not be connected.
……………………………………………………………….2.3 To connect with a PCTo install Active Sync2. Before UsingActiveSync is now ready to install. ExecuteInstallation by pressing ‘install’5Installation of ActiveSync will be performed.It may take several minutes depending onthe environment of the user PC.6Once installation of ActiveSync has beenCompleted finish installation by pressing‘Finish’7Now, connect the PDA with the PCUsing the cradle.8
……………………………………………………………….2.3 To connect with a PCTo install Active Sync 2. Before Using‘Found New hardware wizard’ will start.Select ‘Yes, connect whenever a device is connected’ and press ‘Next’910 ‘Generic USB Serial’ is found .Select ‘Install at listed or specific location’ and press ‘Next’Press ‘Next’ after finding the driver file by pressing ‘Browse’1112 A driver adequate for PDA will beinstalled.13 When the window for compatibilitychecking appears, proceed by pressing ‘Continue’
……………………………………………………………….2.3 To connect with a PCTo install Active Sync2. Before Using14 Once the installation of the driver has beencompleted. Press ‘Finish’15 Installation of ActiveSync has beencompleted and synchronization will start.
……………………………………………………………….3.1 Wireless LANWireless Manager3. FunctionsIt can be controlled bypressing on or off as shown in the figure aboveafter selecting ‘Start’ ->‘Program’ -> ‘WiFi’ fromthe tool bar at the bottomof Windows wallpaper.WLAN on/off state is maintained even afterthe system is rebooted.
……………………………………………………………….3.2 BluetoothBluetooth3. FunctionsUse this menu to activate or deactivate Bluetoothfunction. Bluetooth function can be used only afterturning the module on by pressing ‘Bluetooth On’button.When Bluetooth function is not being used, the functionshould be turned off by pressing ‘Bluetooth Off’ button In order to extend the battery life.Place the Bluetooth device within 10meters of this equipment.Press “search Device” button.Press “Register” button after selecting the Bluetoothdevice to be connected from among the list of devicessearched.
……………………………………………………………….3.2 BluetoothBluetooth3. FunctionsWhen the window asking to enter the pin code pop up,enter the pin code and press “Confirm”. Each Bluetooth device has a unique pin code which is used for certification. Check the pin code with the manufacturer ofThe Bluetooth device. If ‘Registered Device List’ Window appears with a popup window informing that connection is made,connection is successfully achieved.If a failure window pops up, thesteps should be taken again fromthe step #1 in order. Caution : Please refer to the manual of the Bluetooth device to be connected with this equipment as the method to execute each Bluetooth device differs from one device to another. Prior “Pairing” is required for Bluetooth devices. Once pairing is done for Bluetooth devices, connection can be made without being required to pair again later.However, if pairing information is deleted or the device list item is deleted by repair, pairing should be done again.
……………………………………………………………….3.2 BluetoothBluetooth3. FunctionsPress “Registered Device List” button.Press ”Connect/Transmit” button after selecting the item which has been connectedbefore from the “Registered Device List”. A popup window will appear to inform thatthe connection is made and connection status will be displayed in the status blankof the list.In case connection has not been made, start from the step #1 again. In order todisconnect the device connected, press “Disconnect” button.Caution : If the device has been paired before, connection can be made right away without pairing procedure. The list of devices paired before will be shown in the “Registered Device List”.
……………………………………………………………….3.2 BluetoothBluetooth3. FunctionsThe Device Information screen shown informationabout Bluetooth device such as device name,device ID (BD address), support profile, Bluetoothversion, firmware version and software version.In order to delete a device once connected, press“Delete” button after selecting the item to bedeleted. A device currently connected cannot bedeleted. Delete the list after disconnecting thedevice.* Reference : Even after the device is deleted from the ‘Registered Device List’, pin code window can popup if connection is requested by the Bluetooth device. At this time, connection can be made by pressing ‘Confirm’ button after entering the pin code
…………………………………………………………………Problem SolutionProduct does not turn on.4.1 Problem solving 4. Problem solving and Warranty 1. When the product is shipped from the factory, the circuitry is disconnected. Press the power button for 2 seconds or longer, when the product will turn on.2. Check if the battery is fully charged and charge the battery before using the product.No sound from the speaker. 1. Check if the volume of the product is not set at 0.Screen is dark. 1. Enter into ‘Setup’ and adjust the lighting.Problem solving1. Check followings first when a problem occurs while using the product. If the problem is still not solved, first contact the dealer you bought from.2. In case of the delayed response, you can reach the manufacturer.DOTel’s Customer service Phone No. : +82-2-850-3243Some points in manual are unclear.1. Use customer support in the Web site or contact customer center over phone, and a customer support agent will be glade to help you.
…………………………………………………………………Problem SolutionThe product seems to be hot.4.1 Problem solving4. Problem Solving and Warranty1. This product is designed to properly radiate the heat generated inside the product through the case.2. If the product is used for a long period of time or the adapter is connected for long, you may feel warmth from the case please use the product at ease as there is no problem with the product.The PC does not recognize the product.1. If the connection is frequently cut and instable, please connect the product not to a separate hub but directly to the USB terminal of the PC.
…………………………………………………………………4.2 Customer support information4. Problem Solving and Warranty1.1. Contacting the customer service centerContacting the customer service center1) Web site- Before contacting customer support you may wish to try to find troubleshooting help at our website : www.dotel.co.kr- Click ‘Contact’ on the DOT website.- Fill in the form and click the ‘submit’ button.2) Content of serviceFree or charged repair of all the models of PDA and sale of various accessories.2. Before asking for repair2. Before asking for repair1) Be sure to check the content of ‘Problem solving’ in the previous pages before asking for repair.2) Do not forget to backup important data contained in the product in advance. Data may be deleted during repair due to memory formatting, etc. The Company does not take any responsibility for the data lost during servicing.3) Be sure to write your telephone number and address. If there is no contact information for the customer, a problem may occur in the process.3. Quality Assurance3. Quality Assurance1) The warranty of the product is on the overleaf of the manual.2) The products manufactured and sold by the Company are products shipped after going through strict quality control and inspection of DOTel Co., Ltd
…………………………………………………………………4.2 Contacting Customer Support4. Problem solving and Warranty3) Warranty period- Main body : 1 year- Accessories (consumables) : 6 months (battery and items excluding the main body)- Mandatory period to keep spare parts in stock : 3 years from the date of releasing the relevant model.4) Content of warrantyWhen a problem occurs during normal use within the warranty period, the customer service center of the dealer shall provide legitimate material and immaterial service in accordance with Consumer Damage Compensation Regulation by item. In the following cases, repair may be inevitably impossible even within the warranty period and at a cost.a. if the product is out of order due to shock or water-logging caused by a mistake of the consumer,b. if the product has been disassembled or remodeled;c. if the product is out of order due to natural disaster such as fire, earthquake or flood; or d. if the product has been repaired by persons other than the designated service staff of DOTel. Co., Ltd. , or in a non-designated service locationIndividual matters not specified in this article shall be reviewed from the aspect of the internal regulation of DOTel Co., Ltd. For after service and customer support but aiming at convenience of the final consumer.5) Warranty area : Korea4. Expense for repair4. Expense for repair1) If the product has failed due to defect of the product it self within the warranty period, it will be repaired at free of charge in accordance with the warranty standard of the Company and Consumer Damage Compensation Regulation.2)The repair expense shall be decided in accordance with the repair price for each item in the internal regulation of the Company.3) Even within the warranty period, if it falls under article 3-4 above, a certain amount of repair expense will be charged. Please understand as repair may not be possible in some cases.- Hardware manufacturer : DOTel Co., Ltd. www.dotel.co.kr
………………………………………………………………….Product Warranty4.3 Product Warranty4. Problem Solving and WarrantyClassification ContentModel name DOTH-500Date of purchasePurchased fromManufacturing No.Warranty period One year from the date of purchaseProduct failure type Within warranty periodAfter warranty periodIf the failure occurs within 10 days after the purchase Replace N/ARepair ableWhen failure has occurred more than 3times due to same defect Free repair Repair at a costWhen failure has occurred more than 4times due to same defect Replace Repair at a costNot repair ableIf repair is impossible within one month ReplaceReplace after deducting a fixed amount of depreciationIf repair is impossible due to unavailability of repair part ReplaceReplace after deducting a fixed amount of depreciationIf replacement is impossible RefundRefund the amount after deducting a fixed amount of depreciation and adding 10 percentRepair charge regulation
Classification Content WLAN Frequency used: - 802.11b/g: 2412 ~ 2462 MHz Modulation - BPSK / QPSK/CCK/ 16- QAM/ 64-QAM Bluetooth Frequency used: 2402 ~ 2480 MHz Modulation : GFSK Note This device use already certified module (TX Module FCC ID: TWG-SDCMSD30AG) The TX module was certified with both 2.4G and 5G bands but this device only uses 802.11 b/g mode of 2.4G band and the TX module is limited to operated 2.4G b/g mode only.
………………………………………………………………….Product Specifications4.5 Product Specifications4. Problem solving and WarrantyClassification ContentC P U ARM 11 / 800MHzO S Windows CE5.0R A M 128MBR O M 256MBDISPLAY TFT LCD MODULE 5.01INCH,262K COLOR with Touch screen panelINTERFACE USB 2.0 (Micro USB)BATTERY Standard type : 2800mAh SIZE 149(L)*86(W)*17.9(H)mmWEIGHT 200gADAPTER 5V/4A

Navigation menu