D and T VP4726 26” LCD Medical Monitor User Manual

D&T; Inc. 26” LCD Medical Monitor

Contents

User manual

1General Specification THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO D&T CORPORATION AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED AND WRITTEN CONSENT OF D&TCORPORATION. 09.01.2009.01.2009.01.20APPROVEDCHECKEDDRAWNAPPROVALPROPRIETARY NOTEVP4726 / VP4726FGeneral Specification RoHSCompliant
2General Specification TABLE OF CONTENTS1. Overview ----------------- ------------------------------------------------------------------------------ 3 1.1 Scope1.2 Revision History2. General Features ------------------------------------------------------------------------------------- 42.1 General Description3. Product Specifications ------------------------------------------------------------------------------ 53.1 Electrical Specifications3.2 Entire System Block Diagram 3.3 Signal connector PIN assignments3.4 GPIO specification3.5 Environmental and Reliability 4. Regulatory --------------------------------------------------------------------------------------------- 154.1 EMC & Safety Agency Approvals 5. OSD specification ------------------------------------------------------------------------------------- 165.1 OSD User functions/ Messages5.2 OSD representation5.3 OSD System overview6. Mechanical specification ---------------------------------------------------------------------------- 276.1 Product dimension6.2 Label dimension6.3 Filter dimension7. Packing --------------------------------------------------------------------------------------------------- 34 7.1 Packing
3General Specification 1. OverviewVP4726 / VP4726F product has been specifically designed to use the professional applications. This system has been integrated ADC/TMDS Rx/Video decoder and SDI as well. Features include high-quality, motion-adaptive deinterlacing up to 1080p with enhanced low-angle processing, improved low-motion detection, advanced 3D noise reduction, and excellent 3D comb filter performance for PAL and NTSC.1.1 Scope1.2 Revision HistoryPanel changed.1.309.10.06OSD graphic changed.1.209.01.20OSD graphic changed.1.108.12.08Preliminary release.1.008.10.13Change DescriptionParagraphDate
4General Specification 2.1 General Description3 Function – Primary / Secondary screen swap– PIP / PBP1 / PBP2 Select– Record indicatorGPIO portVCOCable DriverCable EqualizerDeserializerGS1578ACNE3 ( GENNUM)GS1574ACNE3 ( GENNUM)GO1525-CTAE3 ( GENNUM)GS1559-CBE2 ( GENNUM)SDI Processor1 x DVI1 x Optical DVI (VP4726F only)1 x D-SUB1 x BNC (SDI)1 x BNC (CVBS)2 x BNC (SVHS Y/C)5 x BNC (Component Y/G, Pb/B, Pr/R, H/CS,VS Input) Input Signal1 x DVI1 x BNC (SDI)Output Signal618(W) x 412(H) x 99.5(D) (mm), 8Kg - Without stand24.330(W) x 16.220(H) x 3.917(D) (inch), 17.64 lbs- Without standUnit DimensionAC/DC Adaptor (AC 100~240V, DC 24V 6.25A)Power SupplyPower, Menu, PIP, Up, Down, Plus, Minus, InputControl KeyResolutionDescription LM260WU2-SLA2 (LG Display)LCD Panel 1920 x 1200 pixelPW338BC-30LScalarVP4726 / VP4726FModelDescriptionItem2. General Features
5General Specification 3.1 Electrical Specifications3. Product Specification3.1.1 Panelmm582.0 X 375.6Active areaTypicalView Angle Free (R/L 178, U/D 178)Viewing Angle (CR>10)-LM260WU2-SLA2 (LG Philips)DescriptionTransmissive mode, normally blackDisplay modeg , Typical3270gWeightmm0.2865(W) x 0.2865(H)Pixel Pitchmm, Typical582.0(H) x 375.6(V) x 41.5(D)Panel Dimensioncd/ m2400 Surface Luminancems , TypicalRise time (Tr) : 5.5Fall time (Tf) : 6.5Response Time(CR≥10)Typical1000 : 1 Contrast Ratiocolors16,777,216Number of Colors-RGB Vertical stripePixel Arrangementpixel1920 x 1200Number of PixelsHard coating(3H), Glare (Low Reflection treatment of the front polarizer)Surface TreatmentInch26” DiagonalSizeUnitDescriptionItem
6General Specification 3.1.2 Power supplyfeet10,0000AltitudeOver-current Protection : 8.125A~9.9AShort Circuit ProtectionOptional Over Voltage CrowbarProtection240mV p-p Max @ 90-264Vac, 50~60Hz : at 20MHz Bandwidth and full load.Ripple and Noise20msec min. Over entire input rangeHold-up time0.5ms for 50% Load change TypTransient Response+24Vdc +/-5%Load regulationLine regulationVoltage /CurrentHz6347Line Frequency RangeVac26490Voltage RangeConfigurationProtectionCurrentRated Line FrequencyRated Voltage%℃℃9585405-300HumidityStorage Temperature+24Vdc at 6.25AOutput+24Vdc +/-1%Operating TemperatureHzVac, Normal60240Dual internal primary current fuse: 250Vac / 5.0AInrush limiting : 50A PEAK @ 90~264Vac, 50~60HzInlet type : IEC320-C14,C83.00A max at 90Vac input50100InputAC/DC AdapterDescriptionJMW1150KA2400F09Model NoUnitMaxTypMinSpecificationItem
7General Specification Less then 20WLess than 20WLess than 20WUnder 130WPower ConsumptionOffGreen Flashing(5 sec. Interval)Green Flashing(5 sec. Interval)GreenPower IndicatorBlankedBlankedBlankedActiveVideoInactiveInactiveActiveActiveVertical SyncInactiveActiveInactiveActiveHorizontal SyncPOWER OffDPMS suspendDPMS StandbyNormal OperationState3.1.3 Power management This monitor saves energy by switching your monitor into a low power mode when it has not detected a video signal for approximately 45 seconds.NOTE : This monitor automatically returns to normal operation when horizontal and vertical syncreturn. This occurs when a video signal is detected.
8General Specification DVI-DConnector576i (50) ITU-R BT.656 720p (60 / 59.94 / 50)SMPTE-296M1080p (30 / 29.97 / 25 / 24 / 24sF / 23.98 / 23.98sF)1035i (60 / 59.94)SMPTE-260M480i (59.94)SMPTE-125M1080i (60 / 59.94 / 50)SMPTE-274MSDINTSC, PALColor systemY/C Separated Video SignalSignal FormatS-VideoTypeSVHS Y/CComposite Video SignalSignal FormatNTSC, PALColor systemC-VideoTypeCVBSFiber Optic TransmissionSignal FormatDigital RGBTypeOptical DVITMDS single linkSignal FormatDigital RGBTypeDVISyncVideoDSUB-15ConnectorPositive or NegativePolarity1920x1200 / 60Hz (154MHz Timing, NON-CRT)Maximum resolution170MHzApplicable maximum pixel frequency 50 ~ 85HzVertical frequencyPositivePolarityAutomatic synchronization for applicable resolution modes which follows industrial standardwithin frequency range of 30 to 93KHz in horizontal and 50 to 85Hz in verticalRangeTTL Level (V high ≥2.0V, V low ≤0.8V)Levelmore than 2KΩTerminal resistanceSeparate H/V sync, Composite H/V sync, Sync On Green Automatic synchronization without external switchType0.7Vp-p ±5%Level75 ohm ±5%Impedance30 ~ 93KHzHorizontal frequencyAnalog RGBTypeVGADescriptionTypeInput Signal3.1.4 Input Signal
9General Specification 3.1.5 Output Signal DVI-DConnector1080p (30 / 29.97 / 25 / 24 / 24sF / 23.98 / 23.98sF)576i (50) 480i (59.94)1035i (60 / 59.94)720p (60 / 59.94 / 50)1080i (60 / 59.94 / 50)ITU-R BT.656 SMPTE-125MSMPTE-296MSMPTE-260MSMPTE-274MSDITMDS single linkSignal FormatDigital RGBTypeDVIDescriptionTypeOutput Signal3.1.6 Input Signal Timing 56.25085.06153.674800 x 600 @85Hz44.90086.95835.5221024 x 768 @43Hz35.50085.03837.927720 x 400 @85Hz36.00056.25035.156800 x 600 @56Hz40.00060.31737.879800 x 600 @60Hz50.00072.18848.077800 x 600 @72Hz49.50075.00046.875800 x 600 @75Hz25.17559.94131.469640 x 400 @60Hz31.50085.08037.86640 x 350 @85Hz25.17570.08731.469640 x 400 @70Hz31.50085.08037.86640 x 400 @85Hz25.17570.08731.469640 x 350 @70Hz25.17559.94031.469640 x 480 @60Hz31.50075.00037.500640 x 480 @75Hz31.50072.80937.861640 x 480 @72Hz25.17559.94131.469640 x 350 @60Hz36.00085.00843.269640 x 480 @85HzPixel clock(MHz)Vertical frequency(Hz)Horizontal frequency(KHz)Resolution
10General Specification 148.50060.00067.5001920 x 1080 @60Hz162.00060.00075.0001600 x 1200 @60Hz154.12559.99974.0991920 x 1200 @60HZ148.50085.00285.9381280 x 960 @85Hz94.20070.01663.9551152 x 864 @70Hz80.00060.05354.3481152 x 864 @60Hz130.37559.98174.0771600 x 1200 @60Hz (**)157.50085.02491.1461280 x 1024 @85Hz135.00075.02579.9761280 x 1024 @75Hz108.50060.01363.9741280 x 1024 @60Hz94.50084.99768.6771024 x 768 @85Hz75.00070.06956.4761024 x 768 @70Hz65.00060.00448.3631024 x 768 @60Hz108.00060.00060.0001280 x 960 @60Hz108.00075.00067.5001152 x 864 @75Hz78.75075.02960.0231024 x 768 @75HzPixel clock(MHz)Vertical frequency(Hz)Horizontal frequency(KHz)Resolution(**) Preferred Timing for 1600 x 1200 @60Hz input
11General Specification 3.2 Entire System Block Diagram
12General Specification 3.3 Signal connector PIN assignments( VP4726F only)
13General Specification 3.4 GPIO specificationGPIO12341234P,S SwapPressing the swap button.Swaps the primary and secondary images.PSPIP,PBP1,PBP2 SelectThe selection of secondary Imageposition button is pressed.GNDCommon groundRecord IndicatorThe record indicator is displayed while a contact closure to the ground pin is present, the indicator is removed when the contacts are opened.The record indicator is displayed in the monitor’s top left corner.RECPSSPSPPIP PBP1 PBP2PSINGLE* GPIO mating connector : RJH 4pin(telephone handset connector)RJ9
14General Specification 3.5 Environmental specification5% ~ 95%, non-condensingHumidity-20℃~ 60℃TemperatureTransportation Conditions10% ~ 85%, non-condensingHumidity-20℃~ 60℃TemperatureStorage Conditions5% ~ 85%, non-condensingHumidityTemperature 0℃~ 40℃Operating ConditionsDescriptionItemMTBF : more than 30,000 hours at 90% confidence level, excluding LCD panel.Reliability items : 3.6 Reliability specification3.6.1 Stress / Time acceleration TestTime (hr)Temp (℃)No Damage7240 ±2Test ResultsCondition3.6.2 Temperature Cycle TestTime (hr)Temp (℃)No Damage95-20~40 ±2Test ResultsCondition
15General Specification 4. Regulatory4.1 EMC & Safety Agency ApprovalsUL Safety Compliance:This LCD monitor is investigated to UL60601-1, 1st Edition, 2006-04-26 (Medical Electrical Equipment, Part 1:General Requirements for Safety)CAN/CSA-C22.2 No. 601.1-M90, 2005 (Medical Electrical Equipment - Part 1:General Requirements for Safety)CE-LVD Compliance:This LCD monitor is investigated to EN 60601-1: 1990 + A1:1993 + A2:1995+ A13:1996 : IEC60601-1:1988 + A1:1991 + A2:1995 + corrigendum 1995,mod.CE-EMC Compliance:This LCD monitor is investigated toEN 60601-1-2: 2001 + EN2001-1-2+ A1:2006( IEC60601-1-2:2001 + A1:2004)FCC Compliance:This LCD monitor is investigated to FCC Part 15 CB Compliance:This LCD monitor is investigated to EN 60601-1: 1990 + A1:1993 + A2:1995
16General Specification 5.1 OSD User functions/ Messages Change the display signal source.-Select DVI OPTICAL(VP4726F) / DVI DIGITAL / DSUB ANALOG / SDI / YPbPr / RGBS / SVIDEO / CVIDEO -With OSD deactivated, Hot key of the auto adjustment control when it pressed over 1 second at DSUB ANALOG source.Input- With OSD deactivated, Hot key of the contrast control and decreases the contrast.- With OSD activated, decreases the adjustment of the selected function.Minus (-)- With OSD deactivated, Hot key of the contrast control and increasesthe contrast.- With OSD activated, enter sub menu and increases the adjustment of the selected function.Plus (+)- With OSD deactivated, Hot key of the brightness control and decreasesthe brightness.- With OSD activated, move the OSD cursor downward.Down (▼)- With OSD deactivated, Activated to OSD menu.- With OSD activated, Exit from main menu or sub menu.Menu- With OSD deactivated, Hot key of the brightness control and increasesthe brightness.- With OSD activated, move the OSD cursor upward.UP (▲)Enable PIP (Picture in Picture) function.- Select PIP,PBP1,PBP2PIPSoft power Turns ON/OFF the monitor.PowerDescriptionKey Name5. OSD specification5.1.1 OSD indicator 5.1.2 INPUT source select VP4726 / VP4726F gives various and very easy graphic user interface. User can easily access function. 8 button keypad, located on the front of monitor, allows the user to make adjustments to various display parameters using on screen menus easily. Be sure that your system power and LED is turned on before operating key board.
17General Specification Increase or decrease the Phase level (Range : 0~100)PHASEIncrease or decrease the sampling frequency (Range : 0~100)CLOCKChange the secondary input source.SOURCEChange the layout. (Single, PIP, PBP1, PBP2)LAYOUTChange the PIP size. (Small, Large)SIZEPIPChange the PIP position.POSITIONSwaps the position of the Primary and Secondary images.SWAPChange the name of a Preset to the Users Name, etcUSER NAME ENTRYSETUPAdjust time until the OSD Menu will disappear after adjusting the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)DURATIONChange the OSD position ( 9 positions )OSD POSITIONChange the OSD language (8 language)LANGUAGEChanges the all OSD value to factory outgoing status.RESET SETTINGSDisable or enable auto source select. (ON: Searches through all possible input source until an active video source is found. OFF: Video input is manually selected.)AUTO SOURCE SELECTKeep still the imageFREEZE FRAMEIMAGEEnlarge the image, move image left and rightZOOM / PANChange the image setting. (Preset 1,2 / User 1,2,3)IMAGE SETTINGAdjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMAFit to the most appropriate screen on the D-SUB Analog signalAUTO ADJUSTAdjust the displayed size.(0~8)OVER SCANSet the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTERAdjust the vertical position of the displayed source image. (Range : 0~100)V POSITIONGreen balance (Only works with USER mode) (Range : 0~100)GREENRed balance (Only works with USER mode) (Range : 0~100)REDBlue balance (Only works with USER mode) (Range : 0~100)BLUEAdjust the horizontal position of the displayed source image. (Range : 0~100)H POSITIONChange the image size (Full, Fill aspect, 1:1, Normal)IMAGE SIZEChange the color temperature mode ( 6500K, 5600K, USER )MODECOLOR TEMPIncrease or decrease the contrast (Range : 0~100)CONTRASTAdjust backlight dimming level (Range : 0~100)BACKLIGHTChanges the richness of color (Range : 50~0~50)COLORChanges the tone of color (Range : 0~100)SATURATIONIncrease or decrease the brightness (Range : 0~100)BRIGHTNESSADJUSTFunction DescriptionsSub-menusMenus5.2 OSD representation5.2.1 DSUB ANALOG / RGBS input source
18General Specification Changes the tone of color (Range : 0~100)SATURATIONIncrease or decrease the contrast (Range : 0~100)CONTRASTChange the secondary input source.SOURCEChange the PIP size. (Small, Large)SIZEAdjust the displayed size.(0~8)OVER SCANChange the image setting. (Preset 1,2 / User 1,2,3)IMAGE SETTINGChange the layout. (Single, PIP, PBP1, PBP2)LAYOUTPIPChange the PIP position.POSITIONSwaps the position of the Primary and Secondary images.SWAPChange the name of a Preset to the Users Name, etcUSER NAME ENTRYSETUPAdjust time until the OSD Menu will disappear after adjusting the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)DURATIONChange the OSD position ( 9 positions )OSD POSITIONChange the OSD language (8 language)LANGUAGEChanges the all OSD value to factory outgoing status.RESET SETTINGSDisable or enable auto source select. (ON: Searches through all possible input source until an active video source is found. OFF: Video input is manually selected.)AUTO SOURCE SELECTIMAGEEnlarge the image, move image left and rightZOOM / PANKeep still the imageFREEZE FRAMESet the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTERGreen balance (Only works with USER mode) (Range : 0~100)GREENRed balance (Only works with USER mode) (Range : 0~100)REDBlue balance (Only works with USER mode) (Range : 0~100)BLUEAdjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMAChange the image size (Full, Fill aspect, 1:1, Normal)IMAGE SIZEChange the color temperature mode ( 6500K, 5600K, USER )MODECOLOR TEMPChanges the richness of color (Range : Green 0~50, Red 0~50)COLORAdjust backlight dimming level (Range : 0~100)BACKLIGHTIncrease or decrease the brightness (Range : 0~100)BRIGHTNESSADJUSTFunction DescriptionsSub-menusMenus5.2.2 DVI OPTICAL / DVI DIGITAL input source
19General Specification Increase or decrease the sampling frequency (Range : 0~100)CLOCKChange the secondary input source.SOURCEChange the PIP size. (Small, Large)SIZEAdjust backlight dimming level (Range : 0~100)BACKLIGHTADJUSTChange the layout. (Single, PIP, PBP1, PBP2)LAYOUTPIPChange the PIP position.POSITIONSwaps the position of the Primary and Secondary images.SWAPChange the name of a Preset to the Users Name, etcUSER NAME ENTRYSETUPAdjust time until the OSD Menu will disappear after adjusting the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)DURATIONChange the OSD position ( 9 positions )OSD POSITIONChange the OSD language (8 language)LANGUAGEChanges the all OSD value to factory outgoing status.RESET SETTINGSDisable of enable auto source select.(ON: Searches through all possible input source until an active video source is found. OFF: Video input is manually selected.)AUTO SOURCE SELECTKeep still the imageFREEZE FRAMEIMAGEEnlarge the image, move image left and rightZOOM / PANChange the image setting. (Preset 1,2 / User 1,2,3)IMAGE SETTINGAdjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS,GAMMAIncrease or decrease the Phase level (Range : 0~100)PHASEAdjust the displayed size.(0~8)OVER SCANSet the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTERAdjust the vertical position of the displayed source image. (Range : 0~100)V POSITIONGreen balance (Only works with USER mode) (Range : 0~100)GREENRed balance (Only works with USER mode) (Range : 0~100)REDBlue balance (Only works with USER mode) (Range : 0~100)BLUEAdjust the horizontal position of the displayed source image. (Range : 0~100)H POSITIONChange the image size (Full, Fill aspect, 1:1, Normal, Anamorphic)IMAGE SIZEChange the color temperature mode ( 6500K, 5600K, USER )MODECOLOR TEMPIncrease or decrease the contrast (Range : 0~100)CONTRASTChanges the richness of color (Range : Green 0~50, Red 0~50)COLORChanges the tone of color (Range : 0~100)SATURATIONAdjusts the sharpness of video image (Range : 0~100)SHARPNESSIncrease or decrease the brightness (Range : 0~100)BRIGHTNESSFunction DescriptionsSub-menusMenus5.2.3 YPbPr input source
20General Specification Change the secondary input source.SOURCEChange the PIP size. (Small, Large)SIZEChange the layout. (Single, PIP, PBP1, PBP2)LAYOUTPIPChange the PIP position.POSITIONSwaps the position of the Primary and Secondary images.SWAPChange the name of a Preset to the Users Name, etcUSER NAME ENTRYSETUPAdjust time until the OSD Menu will disappear after adjusting the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)DURATIONChange the OSD position ( 9 positions )OSD POSITIONChange the OSD language (8 language)LANGUAGEChanges the all OSD value to factory outgoing status.RESET SETTINGSDisable of enable auto source select. (ON: Searches through all possible input source until an active video source is found. OFF: Video input is manually selected.)AUTO SOURCE SELECTKeep still the imageFREEZE FRAMEIMAGEEnlarge the image, move image left and rightZOOM / PANChange the image setting. (Preset 1,2 / User 1,2,3)IMAGE SETTINGAdjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMAAdjust backlight dimming level (Range : 0~100)BACKLIGHTAdjust the displayed size.(0~8)OVER SCANSet the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTERAdjust the vertical position of the displayed source image. (Range : 0~100)V POSITIONGreen balance (Only works with USER mode) (Range : 0~100)GREENRed balance (Only works with USER mode) (Range : 0~100)REDBlue balance (Only works with USER mode) (Range : 0~100)BLUEAdjust the horizontal position of the displayed source image. (Range : 0~100)H POSITIONChange the image size (Full, Fill aspect, 1:1, Normal, Anamorphic)IMAGE SIZEChange the color temperature mode ( 6500K, 5600K, USER )MODECOLOR TEMPIncrease or decrease the contrast (Range : 0~100)CONTRASTChanges the richness of color (Range : Green 0~50, Red 0~50)COLORChanges the tone of color (Range : 0~100)SATURATIONAdjusts the sharpness of video image (Range : 0~100)SHARPNESSIncrease or decrease the brightness (Range : 0~100)BRIGHTNESSADJUSTFunction DescriptionsSub-menusMenus5.2.4 SVIDEO / CVIDEO input source
21General Specification Adjust the displayed size.(0~8)OVER SCANChange the image setting. (Preset 1,2 / User 1,2,3)IMAGE SETTINGChange the secondary input source.SOURCEChange the PIP size. (Small, Large)SIZEChange the layout. (Single, PIP, PBP1, PBP2)LAYOUTPIPChange the PIP position.POSITIONSwaps the position of the Primary and Secondary images.SWAPChange the name of a Preset to the Users Name, etcUSER NAME ENTRYSETUPAdjust time until the OSD Menu will disappear after adjusting the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)DURATIONChange the OSD position ( 9 positions )OSD POSITIONChange the OSD language (8 language)LANGUAGEChanges the all OSD value to factory outgoing status.RESET SETTINGSDisable of enable auto source select.(ON: Searches through all possible input source until an active video source is found. OFF: Video input is manually selected.)AUTO SOURCE SELECTIMAGEEnlarge the image, move image left and rightZOOM / PANAdjust backlight dimming level (Range : 0~100)BACKLIGHTKeep still the imageFREEZE FRAMESet the sharpness of image (Softest, Soft, Normal, Sharp, Sharpest)FILTERGreen balance (Only works with USER mode) (Range : 0~100)GREENRed balance (Only works with USER mode) (Range : 0~100)REDBlue balance (Only works with USER mode) (Range : 0~100)BLUEAdjust GAMMA value (VIDEO,BYPASS,1.8,2.0,2.2,2.4,2.6,PACS)GAMMAChange the image size (Full, Fill aspect, 1:1, Normal, Anamorphic)IMAGE SIZEChange the color temperature mode ( 6500K, 5600K, USER )MODECOLOR TEMPIncrease or decrease the contrast (Range : 0~100)CONTRASTChanges the richness of color (Range : Green 0~50, Red 0~50)COLORChanges the tone of color (Range : 0~100)SATURATIONIncrease or decrease the brightness (Range : 0~100)BRIGHTNESSADJUSTFunction DescriptionsSub-menusMenus5.2.5 SDI input source
22General Specification Adjust backlight dimming level.Setting the backlight too low will cause dark image and too high will decrease the backlight lifetime.BACKLIGHTFit to the most appropriate screen on the D-SUB Analog signalAUTO ADJUSTAdjusts the sharpness of video imageSHARPNESSChanges the tone of colorSATURATIONChanges the richness of color (Range : Greenish 0~50, Reddish 0~50)COLORDefault 6500K color setting COLOR TEMP 6500KDefault 5600K color settingCOLOR TEMP 5600KDefault 6500K color setting. When USER is selected, Red, Green and Blue values are changeable by the userCOLOR TEMP USER*DSUB / DVI OPTICAL / DVI DIGITAL input sourceFULL FILL ASPECT1:1 NORMAL*YPbPr / RGBS / SDI / CVIDEO / SVIDEO input sourceFULL FILL ASPECT 1:1NORMAL ANAMORPHICIMAGE SIZEPHASE Do not adjust freely. It will adjust fine state automatically after auto adjustment.When phase value is wrong, the image have a noise.CLOCK Do not adjust freely. It will adjust fine state automatically after auto adjustment.When frequency value is wrong, the horizontal image have a wrong size or noise.Press the CONTRAST button to display the ADJUST menu or +,- hot key.Setting the Contrast too high or too low will cause loss of some grayscales.CONTRASTPress the BRIGHTNESS button to display the ADJUST menu or UP,DOWN hot key.Setting the brightness too high or too low will decrease the amount of visible grayscales.BRIGHTNESSFunction DescriptionsMenus5.3 OSD overviewCAUTION : FILL ASPECT,NORMALSize are depends on input size ratioCAUTION : FILL ASPECT,NORMAL,ANAMORPHIC Size are depends oninput size ratio
23General Specification Enable 10% over scan of original input imageOVER SCANFILTER Adjusts the sharpness of video image.GAMMA Adjusts the gamma curve of video image.1.8 2.0 2.2 2.4 2.6 PACS VIDEO< NOTICE > BYPASS is depend on panel gamma value, please refer to the panel specificationAdjusts the horizontal position of the image. It will return to the default state when executing AUTOADJUST or RESET SETTINGSV POSITIONAdjusts the horizontal position of the image. It will return to the default state when executing AUTOADJUST or RESET SETTINGSH POSITIONFunction DescriptionsMenusNORMALSOFTSOFTESTSHARPSHARPEST0 : 1 : 2 : 3 : 4 : 5 : 6 : 7 : 8 :
24General Specification Change the OSD language (8 language)ENGLISH / GERMAN / FRENCH / SPAINISH / ITALIAN / JAPANESE / CHINESE / KOREAN LANGUAGEOSD POSITION Adjust the position of OSDFREEZE FRAME Freeze the main image. Do not support secondary image freeze at PIP modeControls the zoom in/out of the image.Controls the PAN in/out of the image.ZOOM / PANSave the 5 user’s setting about BRIGHTNESS,CONTRAST,COLOR TEMP,FILTER value separately.(PRESET 1~2, USER 1~3)IMAGE SETTINGFunction DescriptionsMenus0 step : 4 step : 9 step :13 step : 18 step : 22 step :26 step : 30 step :
25General Specification Change PIP mode sub window size. SMALL LARGE25 % / Panel size 33 % / Panel size * CAUTION : Do not change input Source aspect ratio and the pip image size is changeable depend on input timing.PIP SIZESelect PIP source input. You can change other sub windows through OSD pip menu. Below chart is PIP matching table with main and sub window. O¹ : Support up to UXGA,60Hz (162MHz)When main window is running at 1080p,sub window supports up to 1080i mode only.When main window is running below 1080i,sub window supports up to 1080p mode.PIP SOURCEVP4726F onlyChange sub window layout (SINGLE,PIP,PBP1,PBP2)PIP : Main/Sub window doesn’t change aspect ratio.PBP1 : Main/Sub window doesn’t change aspect ratio.PBP2 : Main/Sub window H/V display 1:1 size.PIP LAY OUTPut user’s name or etc into set.USER NAME ENTRYPIP POSITION Change PIP mode sub window position.AUTO SOURCE SELECTWhen AUTO SOURCE SELECT is on, the monitor automatically search input source except PIP subSource.Reset the unit to factory outgoing status.RESET SETTINGSAdjust the time until the OSD Menu will disappear after adjusting the menuOSD DURATIONFunction DescriptionsMenusOOOOOOOXDVI OPTICALOOXXO¹XXYPbPrXXOOXOOSVIDEOXXOOXOOCVIDEOOOXXO¹XXRGBSXXO¹O¹XO¹OSDIOOXXO¹XXDSUB ANALOGOOXXOXXDVI DIGITALOOOOOOODVI OPTICALMa I n w I ndowSVIDEOCVIDEORGBSYPbPrSDIDSUB ANALOGDVI DIGITALInput sourceSub windowMainSubMainSubMainSub MainSubMainSubMainSubMainSubMain SubMainSubMainSubMainSub
26General Specification Change main window and sub window position on PIP,PBP1,PBP2.SWAPFunction DescriptionsMenusMainSubMainSubSubMain SubMainPIPPBP1SubMain SubMainPBP2
27General Specification 6. Mechanical Specifications6.1 Product dimension
28General Specification The color same as rear housing(Gray)Base ColorPolyester film (75Demicron)Material140X31(mm)SizeShall not be tilted more than 1mmTiltThe left bottom side of rear-coverLocationRating Label (This may vary based on the Customer's request, and the changed contents of the Rating Label shall not be specified in this specification.) VP4726 / VP4726FModel NO.ConMed LinvatecBrand Logo6.2 Label dimension6.2.2 Product label6.2.1 Connector (Function) label
29General Specification Label shall not be tilted more than 1mm TiltBlackBase ColorPolyester film 125uMaterial57.5 x 64.5 (mm)SizeThe center of rear-coverLocation6.2.3 AC ADAPTOR Label
30General Specification 6.2.4 BOX labelWhiteBase ColorArt paperMaterial161X63.5(mm)SizeShall not be tilted more than 1mmTiltThe left and right center side Location6.2.5 Membrane switchThe color same as front bezelBase ColorPc auto texMaterial185X38.5(mm)SizeShall not be tilted more than 1mmTiltThe center bottom side of front bezelLocation
31General Specification 6.3 Filter dimensionDouble side Anti-Reflection coatingCoatingNo contamination, No discoloration, No alien substanceSurfaceBetween Blue-Violet & Red-Violet Reflection colorNo harmful defect such as void, groove, and contaminationAppearancemm(576 +0/-1mm) x (356 +0/-1mm) x (3±0.3mm)Size%97% (at 545nm of the wavelength)(The average transmittance in the range of 450 ~ 650nm should be 97%)TransmittancenmLess than 1% (450 ~600nm)Average reflectanceUnitDescriptionItem6.3.1 General specification
32General Specification 14.5KgWeight657 mmHeight230 mmDepth750 mmWidth7.1 Packing7.1.1 Carton Dimension 7. PackingThis unit conforms to all specifications in the "General Specification VP4726 / VP4726F ” document, dated 09.01.20
33General Specification 7.1.2 Accessory

Navigation menu