DASAN ELECTRON DA-581BT PART15 SPREAD SPECTRUM TRANSMITTER User Manual DA 581BT

DASAN ELECTRON PART15 SPREAD SPECTRUM TRANSMITTER DA 581BT

Users Manual

- 2 - This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions ; (1) this device may not cause harmful Interference, and (2) this device must accept any interference received, Including interference that may cause undesired operation. Dasan Electron Co.,Ltd. Product: Bluetooth Headset Model No : DA-581BT FCC ID : WF2DA-581BT Bluetooth Headset Owner’s Manual DA-581BT - 3 -• CAUTION The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. • INFORMATION This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. The use of a permanently attached antenna or of an antenna that user a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of required this section. The manufacturer may design the unit so that broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. ※ STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, users, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocated the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help.
- 4 - The unit is a wireless comfort Bluetooth® headset for mobile phones and offices. When mobile phones replace the ordinary phones at the office, you need a comfortable and ergonomic solution for those who spend long hours on the phone. The unit such a solution, a truly comfortable headset with good sound quality, built for comfortable all day wearing. As an accessory, there is an USB Bluetooth dongle for the PC. With the dongle, you can connect your headset to a computer and use it as an audio device for VoIP applications, for example SkypeTM . Features z Bluetooth Version 2.1, with improved data transfer, security and connectivity. z Up to 15 hours talk time. z At least 96 hours stand by time z Up to 10 meters working range (class 2) z Volume control buttons z Answer button z Dedicated microphone mute button z Last number redial z Voice dial support z Low battery indication z Adjustable headband and soft ear cushion for all day wearing comfort z LED status indication z Desktop charging stand with LED charging status indicators(Option) z Car-Charger (Option) Introduction - 5 - Charging LED and LED indicators <DA-581BT(No charging cradle)> Direct Charging from DC5V switching power adapter. Overview If the headset has been out of use for some item, it may take up to five hours to charge it fully. Normal charging time is 3-4 hours. Low battery is indicated by the flashing red LED on the headset.. DC power jack / Car Charger Headset Hanger : For your convenience, fix the headset hanger on any place available. Wall Adapter Car Charger(Option)
- 6 - <DA-579BT> On Cradle charging From wall adapter Headset controls Headset Controls Headset Controls If the headset has been out of use for some item, it may take up to five hours to charge it fully. Normal charging time is 3-4 hours. Low battery is indicated by the flashing red LED on the headset. The LED’s on the charging stand indicates charging status. The headset can only be placed in one direction in the charging stand. - 7 - Headband adjustment Turn on the headset Press and hold the answer button for 2 seconds. Release the button when the LED flashes green and a short beep is heard in the speaker. Turn off the headset Press and hold the answer button for 4 seconds. Release the button when the LED flashes red 3 times. Prior to using the headset, it must be paired and connected to another Bluetooth device, such as a mobile phone. For specific instructions, check the users guide of your phone. Adjust the headband to a comfortable fit by sliding the headband up or down. There are two different types of ear cushions supplied with the product, leatherette and foam. Turning the headset on and off Pairing
- 8 - General procedure z Turn on Bluetooth on your phone z Put the headset in pairing mode (make sure the headset is switched off, press and hold the answer button for 4-5 seconds until the LED flashes red and green) z Perform a search for Bluetooth devices on your phone. z Connect to >>device logo<< when found. The PIN code is 0000 (four zeros) Different phones have different ways to handle Bluetooth devices. Read the users manual of your phone for more info. Some phone for more info. Some phones will connect to the headset automatically when it is within range, for example when you return to your office. For other phones, it may be necessary to reconnect manually when the connection has been broken. The pairing mode is active for 3 minutes. After that, the headset will enter standby mode. .. Answer a call z Press the answer button briefly. Make a call z Dial the number on the mobile phone and press the answer button briefly. End a call z Press the answer button briefly, or end the call on the mobile phone. Using the headset - 9 - Headset ring alert adjustment The type of ring alert signal in the headset will vary depending on your telephone model. Some phones will transfer your ordinary ring melody to the headset. In these cases, the volume and ring melody adjustments are made in the phone. With other telephone models, there is an internal ringer alert in the headset when you receive an incoming call. This ringer alert tone can be set to two different modes. For using this function, disconnect Bluetooth device with the phone. z Press and hold Volume Up and Down simultaneously for 1 second. A beep tone is heard in the speaker. z To resume the default setting, press Volume Up and Volume down Volume adjustment z Press volume up/volume down to adjust the listening volume. There is a small notch on each volume button that makes them easy to find. The headset listening volume can also be adjusted on the phone. Note that high listening volume settings may cause echo or other noise on the line, for one or both parties on the line. Try to lower the listening volume if this is the case. Important! – High listening volume settings may be harmful to your hearing.
- 10 - z simultaneously briefly. A beep tone is heard in the speaker. Mute z Press and release the mute button. Press again to resume the call. A beep tone is heard every thirty seconds when mute mode is active. Transfer sound from/to the headset or mobile phone z To transfer the sound from the phone to the headset, use the mobile phone. Refer to the manual of the mobile phone. Last number redial z Press the answer button briefly once. And then phone number will be listed on the phone. z Press the answer button briefly again to dial. Voice dialing z Press and hold the answer button 2-3 seconds to activate voice dial. In general, voice dial must be activated on your phone before you can use it. For more information on voice dialing and voice commands, refer to your phone’s user guide. Safe and efficient use Do not expose your product to humidity, liquid or extreme temperature conditions. Such conditions, or other rough treatment such as dropping or bending the product may damage it. Do not use any accessories or chargers other than original intended for use with this product. Neither headset nor charger contain any user serviceable Technical information - 11 -parts, and must not be opened. A Bluetooth device use radio signals to communicate with other devices. The power of this radio signal is low, maximum 0.001 Watts. Do not use the product where it is forbidden, for example in air planes, at hospitals, in blasting areas or in explosive atmospheres. Radio signals may interfere with other electronic devices, especially if these are not shielded. Permanent hearing loss may occur if headsets are used at high listening volumes for longer periods of time. Set the volume to a safe level. You can adapt to high listening volume over time, especially in a noisy environment where the level of sound may seem normal even if the volume is high. Reduce the time you use a headset with high listening volume. Battery information The device is equipped with a rechargeable Lithium-polymer battery. A new battery will need a few charging cycles before it can reach maximum capacity. A fully charged battery will loose its charge over time even if the headset is not used. Battery capacity and life span may be reduced if the device is exposed to extreme high or low temperatures, for example if it is left in a car. A device with a cold or hot battery may stop working until it is back to normal (room) temperature. Battery capacity at temperatures below -0 oC is reduced. Never dispose of batteries in open fire since they may explode. Always dispose of use batteries and electronic devices according to local recycling regulations.
- 12 - Troubleshooting If you have problems connecting the headset to your phone, do as follows: z Check that the headset is charged, turned on and within 10 meters of the phone. z Check that Bluetooth is switched on your phone. z Check that the headset is listed as a headset device in your phone and also connected. You may need to re-connect to the headset z Try removing the headset from the phone, then pair and connect again. z If the headset stops functioning, even though it is fully charged: Reset the headset by switching it off, wait for 15 seconds and then turn it on again. You might try to reset the phone as well. Some features are not possible to use with a certain phone: z Check the users manual of your phone for missing settings or functions that needs to be activated. z Different mobile phone manufacturers may implement Bluetooth functions in different ways. The unit should work with all phones that support the Headset and Hands-free Bluetooth profiles, but functionality may vary depending on the telephone model you use. You might also want to check for the latest firmware for your phone. Maintenance Your headset is a technically advanced device containing circuit boards and fine mechanics, made from top grade component. To increase reliability and life span, always treat your headset with care. Help and tips - 13 -z Do not expose the headset to moist, liquids, rain or dust. z Store the product at a dry and dust-free location. z For cleaning, use a dry cloth. z Do not store a fully charged headset in the charging stand for longer periods of time. z Ear cushions are available as spare parts. We will repair or replace, at our opinion, this product if found defective due to materials or workmanship within the warranty period beginning from the original date of purchase. This product is warranted by authorized representative for the period specified. The Original dated purchase receipt must be presented to the authorized service center when service is rendered. On all carry-in models, transportation to and from the service station is the responsibility of the purchaser. This warranty does not cover damages due to accident, fire, flood, earthquake and/or other acts of God; misuse, incorrect line voltage, improper installation, improper or unauthorized repairs, commercial use or damages occurred in shipping. Exterior and interior finish, lamps, glass, plastics parts and temperature probes are not covered under this warranty. Customer adjustment according to the owner’s manual are not covered under this warranty. This warranty is automatically void if the serial number is missing or altered. Warranty and service
- 14 - Equipment Specification Equipment Name Bluetooth Headset Model No DA-581BT Brand Name None Usage Wireless Hands-free for Cellular phone Serial Number Prototype ITU emission Code 1M00F1D Oscillation Type PLL (Phase Local Loop) Modulation Type FHSS (Frequency Hopping Spread Spectrum), GFSK Emission Type F1D Maximum Power 4.71㎽ (6.73 ㏈m)** Operated Frequency TX : 2 402 ㎒ ~ 2 480 ㎒ RX : 2 402 ㎒ ~ 2 480 ㎒ Channelspacing / Number 1 ㎒ / 79 Ch Communication Type Half duplex Communication access Method FHSS (Frequency Hopping Spread Spectrum) Final Amplifier U1 Weight / Dimension 100g / 60(L) ㎜ x 30(W) ㎜ x 40(D) ㎜ Operation temperature - 20℃~ + 80℃ Power Source DC 3.7 V, 300 ㎃ (Lithium polymer recharge battery) Antenna Description Type: Chip type, Connect type: Fixed on PCB, Length: 9 mm, Gain: 3.5㏈i Bluetooth Profile A2DP - 15 -

Navigation menu