DASAN Zhone Solutions 67X8 1)XDSL 4-Port 802.11N WiFi IAD; (2)XDSL 4-Port 802.11N WiFi Gateway; (3)XDSL Bonded 4-Port WiFi Gateway (4)XDSL Bonded (17A) 4-Port WiFi Gateway User Manual manual

Download:
Mirror Download [FCC.gov]
Document ID	1862232
Application ID	a6o4XjZNzEKT7iYV/e/GtA==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	102.82kB (1285228 bits)
Date Submitted	2012-12-18 00:00:00
Date Available	2012-12-19 00:00:00
Creation Date	2012-07-12 10:27:13
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2012-12-13 14:31:45
Document Title	Microsoft Word - ZHONE 6748_User Manual（优化）.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	User

ZHONE
6748-W1-EU,6748-W1-UK,6748-W1-NA
User Manual
VER: 1.0
FCC Statement
This equipment has been tested and found to comply with the limits for
a C lass B digital device, pursuant to part 15 of t he FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void
the user ’s aut hority to operate this equipment. (Example- use only
shielded interface cables when connecting to computer or peripheral
devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter. This eq uipment should be in stalled and operated with a
minimum distance of 20 centimeters between the radiator and your
body.
This equipment complies with Part 15 of the FCC Rules.Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Caution!
The m anufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such
modifications could void the user authority to operate the equipment.
FCC - PART 68
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the bottom of this equipment
is a label that contains, among other information, a product identifier in
the form at US: 6R TDL01B67X8. If reques ted, t his number must b e
provided to the telephone company.
This equipment uses the following USOC jacks: RJ11C.
REN (RINGER EQUIV ALENT NUMBERS) STATEMENT Notice:
The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on
an interface may consist of any combination of devices subject only to
the requirement that the sum of the Ringer Equivalence Numbers of all
the devices does not exceed 5.
ATTACHMENT LIMITATIONS STATEMENT
Notice: This equipment meets telecommunications network protective,
operational and safety requirements as prescribed in the appropriate
Terminal Equipment Technical Requirements document(s). This is
confirmed by marking the equipment with the Industry Canada
certification number. The Department does not guarantee the
equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together.
This precaution may be particularly important in rural areas. Caution:
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or
electrician, as appropriate
CE Statement
Hereby, Zhone Technologies, Inc. declares that this device is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
User Manual
Contents
Safety Precautions ............................................................................................. 1
Overview ............................................................................................................ 2
2.1
Application ............................................................................................. 2
2.2
Features ................................................................................................ 3
2.3
Standards Compatibility and Compliance.............................................. 4
Hardware Description and Installation ............................................................... 5
3.1
3.2
Hardware Description ............................................................................ 5
3.1.1
Front Panel ................................................................................. 5
3.1.2
Rear Panel and Side Panel ........................................................ 7
Hardware Installation............................................................................. 8
3.2.1
Choosing the Best Location for Wireless Operation................... 8
3.2.2
Connecting the Device ............................................................... 8
PC Network Configuration and Login............................................................... 10
4.1
PC Network Configuration ................................................................... 10
4.2
Logging In to the DSL Router .............................................................. 12
Web-Based Management ................................................................................ 13
5.1
5.2
5.3
5.4
5.5
Quick Setup ......................................................................................... 13
Advanced Setup .................................................................................. 16
5.2.1
Layer2 Interface........................................................................ 16
5.2.2
WAN Service ............................................................................ 20
5.2.3
3G WAN Service....................................................................... 28
Wireless............................................................................................... 30
5.3.1
Basic Settings ........................................................................... 30
5.3.2
Security..................................................................................... 31
Voice.................................................................................................... 33
5.4.1
VoIP Status ............................................................................... 34
5.4.2
SIP Basic Setting ...................................................................... 34
5.4.3
SIP Advanced Setting ............................................................... 38
5.4.4
SIP Extra Setting ...................................................................... 42
5.4.5
SIP Debug Setting .................................................................... 42
Management........................................................................................ 43
5.5.1
Access Control.......................................................................... 43
User Manual
5.5.2
Update Software ....................................................................... 44
Q&A.................................................................................................................. 45
ii
User Manual
Safety Precautions
Read the following information carefully before operating the device. Please follow
the following precaution items to protect the device from risks and damage caused
by fire and electric power:

Use volume labels to mark the type of power.

Use the power adapter that is packed within the device package.

Pay attention to the power load of the outlet or prolonged lines. An
overburden power outlet or damaged lines and plugs may cause electric
shock or fire accident. Check the power cords regularly. If you find any
damage, replace it at once.

Proper space left for heat dissipation is necessary to avoid any damage
caused by overheating to the device. The holes on the device are designed
for heat dissipation to ensure that the device works normally. Do not cover
these heat dissipation holes.

Do not put this device close to a place where a heat source exits or high

Do not put this device close to a place where is over damp or watery. Do not

Do not connect this device to any PC or electronic product, unless our
temperature occurs. Avoid the device from direct sunshine.
spill any fluid on this device.
customer engineer or your broadband provider instructs you to do this,
because any wrong connection may cause any power or fire risk.

Do not place this device on an unstable surface or support.
User Manual
Overview
The xDSL Router integrates wireless LAN, USB, and VoIP service into one unit. It
is designed to provide a simple and cost-effective xDSL Internet connection for a
private Ethernet and 802.11b/802.11g/802.11n wireless network. The Router
combines high-speed xDSL Internet connection, Ethernet uplink, IP routing for the
LAN and wireless connectivity in one package. It is usually preferred to provide
high access performance applications for the individual users, the SOHOs, and the
small enterprises. The Router supports 3G WAN service.
The Router is easy to install and use. The Router connects to an Ethernet LAN or
computers via standard Ethernet ports. The xDSL connection is made using
ordinary telephone line with standard connectors. You can connect the Ethernet
interface of WAN to Internet with Ethernet cable for ETH uplink. Multiple
workstations can be networked and connected to the Internet by a single Wide
Area Network (WAN) interface and single global IP address. The advanced
security enhancements, packet filtering and port redirection, can help protect your
network from potentially devastating intrusions by malicious agents from outside
your network.
Network and Router management is done through the web-based management
interface that can be accessed through the local Ethernet using any web browser.
You may also enable remote management to enable configuration of the Router via
the WAN interface.
2.1 Application

Home gateway

SOHOs

Small enterprises

Higher data rate broadband sharing

Audio and video streaming and transfer

PC file and application sharing

Network and online gaming

Voice over IP (VoIP)

USB storage
User Manual

3G WAN service
2.2 Features

User-friendly GUI for web configuration

Several pre-configured popular games. Just enable the game and the port

Compatible with all standard Internet applications

Industry standard and interoperable DSL interface

Simple web-based status page displays a snapshot of system configuration,

Downloadable flash software updates

Support for up to 8 permanent virtual circuits (PVC)

Support for up to 8 PPPoE sessions

Support RIP v1 & RIP v2
settings are automatically configured.
and links to the configuration pages

WLAN with high-speed data transfer rates, compatible with IEEE 802.11b/g/n

Optimized Linux 2.6 Operating System

IP routing and bridging

Asynchronous transfer mode (ATM) and digital subscriber line (DSL) support

Packet Transfer Mode (PTM)

Ethernet (ETH) Transfer Mode

Point-to-point protocol (PPP)

Network/port address translation (NAT/PAT)

Quality of service (QoS)

Wireless LAN security: WPA, 802.1x, RADIUS client

Universal plug-and-play(UPnP)

File server for network attached storage (NAS) devices

Print server

Web filtering

Management and control
Web-based management (WBM)
Command line interface (CLI)
TR-069 WAN management protocol
Simple Network Management Protocol (SNMP)

Remote update

System statistics and monitoring
User Manual

DSL router is targeted at the following platforms: DSL modems, wireless
access points and bridge.
2.3 Standards Compatibility and Compliance

Support application level gateway (ALG)

ITU G.992.1 (G.dmt)

ITU G.992.2 (G.lite)

ITU G.994.1 (G.hs)

ITU G.992.3 (ADSL2)

ITU G.992.5 (ADSL2+)

ITU G.993.1 (VDSL)

ITU G993.2 (VDSL2)

3G (WCDMA, CDMA2000, TD-SCDMA)

ANSI T1.413 Issue 2

IEEE 802.3

IEEE 802.3u

IEEE 802.11b

IEEE 802.11g

IEEE 802.11n

RFC3261 (SIP for VoIP)
User Manual
Hardware Description and Installation

Note:
The figures in this document are for reference only.
3.1 Hardware Description
3.1.1 Front Panel
Figure 1 Front panel
The following table describes the indicators on the front panel.
Indicator Color Status
Description
On
Green
Power
Red
DSL
Green
The software is upgrading.
Off
The device is powered off.
On
The device is initiating.
Blink
The software is upgrading.
On
DSL link has established.
Blink
The DSL line is training.
On
Internet
Red
Green
Device is powered off.
Internet is synchronized successfully in the route
mode.
Blink
Internet data is being transmitted.
Off
Ethernet interface is disconnected.
On
On
WAN
normally.
Blink
Off
Green
The device is powered on and the device operates
Authentication has failed.
The WAN interface is connected to the Ethernet
Blink
cable.
Network data is transmitting.
Off
The WAN interface is not connected to the
User Manual
Indicator
Color
Status
Description
Ethernet cable.
On
LAN
1/2/3/4
WiFi
Green
Green
Blink
The Ethernet interface is disconnected.
On
WIFI is enabled.
Blink
On
Green
Blink
Off
On
USB1/2
Phone1/2
Green
Green
interface.
Off
Off
WPS
The Ethernet interface is connected.
Data is being transmitted through the Ethernet
Data is being transmitted through the wireless
interface.
WIFI is disabled.
Connection succeeds under Wi-Fi Protected
Setup.
Negotiation is in progress under Wi-Fi Protected
Setup.
Wi-Fi Protected Setup is disabled.
The connection of 3G or USB flash disk has
established.
Blink
Data is being transmitted.
Off
No signal is detected.
Off
No FXS signal is detected.
Blink
The user data is passing through FXS port.
On
The FXS interface is ready to work.
User Manual
3.1.2 Rear Panel and Side Panel
Figure 2 Rear panel
Figure 3 Side
panel
The following table describes the interfaces and the buttons.
Interface
Description
DSL
Phone1/2
LAN 4~1
WAN
Reset
USB1/2
RJ-11 port. Connect the router to DSL connector or splitter through
telephone cable.
RJ-11 port, using the telephone cable to connect the telephone set.
RJ-45 port, for connecting the router to a PC or another network
device.
For connecting Ethernet cable to provide Ethernet uplink.
Press the button for at least 1 second and then release it. System
restores the factory default settings.
USB port, for connecting the 3G network card or other USB storage
devices.
Power
On/Off
Power switch.
Power interface, for connecting the power adapter.
WiFi
WiFi switch, for enabling or disabling the WiFi function.
User Manual
Interface
Description
This button is used for enabling WPS PBC mode. If WPS is enabled,
WPS
press this button, and then the wireless router starts to accept the
negotiation of PBC mode.
Warning:
Do not press the Reset button unless you want to clear the current settings. The
Reset button is in a small circular hole on the rear panel. If you want to restore the
default settings, please press the Reset button gently for 1 second with a fine needle
inserted into the hole and then release the button. The system reboots and returns to
the factory defaults.
3.2 Hardware Installation
3.2.1 Choosing the Best Location for Wireless Operation
Many environmental factors may affect the effective wireless function of the DSL
Router. If this is the first time that you set up a wireless network device, read the
following information:
The access point can be placed on a shelf or desktop, ideally you should be able to
see the LED indicators in the front, as you may need to view them for troubleshooting.
Designed to go up to 100 meters indoors and up to 300 meters outdoors, wireless
LAN lets you access your network from anywhere you want. However, the numbers of
walls, ceilings, or other objects that the wireless signals must pass through limit signal
range. Typical ranges vary depending on types of materials and background RF
noise in your home or business.
3.2.2 Connecting the Device
Step 1
Connect the DSL port of the router and the Modem port of the splitter
with a telephone cable; connect the phone to the phone port of the
splitter through a cable; and connect the incoming line to the Line port of
the splitter.
The spliiter has three ports:
 Line: Connect to a wall phone jack (RJ-11 jack)
 Modem: Connect to the Line interface of the router
User Manual
 Phone: Connect to a telephone set
Step 2
Connect the LAN port of the router to the network card of the PC through
an Ethernet cable.
Step 3
Plug the power adapter to the wall outlet and then connect the other end
of it to the Power port of the router.
The followig figure displays the connection of the DSL router, PC, and telephones.
Figure 4 Connecting the DSL router
Note:
If you use 3G WAN service, connect the 3G USB data card to the USB port of
the router.
If you use the Ethernet uplink, connect the WAN interface that is defined to the
Internet with Ethernet cable.
The xDSL uplink, 3G WAN service, and Ethernet uplink can not coexist.
User Manual
PC Network Configuration and Login
4.1 PC Network Configuration
Each network interface on the PC should either be configured with a statically defined
IP address and DNS address, or be instructed to automatically obtain an IP address
using the network DHCP server. DSL router provides a DHCP server on its LAN and
it is recommended to configure your LAN to automatically obtain its IP address and
DNS server IP address.
The configuration principle is identical but should be carried out differently on each
operating system.
The following displays the TCP/IP Properties dialog box on Windows XP.
10
User Manual
Figure 5 IP and DNS configuration
TCP/IP configuration steps for Windows XP are as follows:
Step 1
Choose Start > Control Panel > Network Connections.
Step 2
Right-click the Ethernet connection icon and choose Properties.
Step 3
On the General tab, select the Internet Protocol (TCP/IP) component
and click Properties.
Step 4
The Internet Protocol (TCP/IP) Properties window appears.
11
User Manual
Step 5
Select the Obtain an IP address automatically radio button.
Step 6
Select the Obtain DNS server address automatically radio button.
Step 7
If you want to set the IP address and subnet mask manually, you can set
the IP address and subnet mask of the computer to 192.168.1.x and
255.255.255.0 respectively. The range for x is from 2 to 254.
Step 8
Click OK to save the settings.
4.2 Logging In to the DSL Router
To log in to the DSL router, do as follows:
Step 1
Open a Web browser on your computer.
Step 2
Enter http://192.168.1.1 (the default IP address of the DSL router) in the
address bar. The login page appears.
Step 3
Enter the user name and the password. The default username and
password of the super user are admin and admin. The username and
password of the common user are user and user. You need not enter
the username and the password again if you select the option
Remember my password. It is recommended to change these default
values after logging in to the DSL router for the first time.
Step 4
Click OK to log in to the Web page. Otherwise, please click Cancel to
exit the login page.
12
User Manual
Figure 6 Login page
After logging in to the DSL router as a super user, you can query, configure, and
modify all the settings, and diagnose the system
Web-Based Management
This chapter describes how to use Web-based management of the DSL router, which
allows you to configure and control all of DSL router features and system parameters
in a user-friendly GUI.
5.1 Quick Setup
Choose Quick Setup and the following page is displayed.
13
User Manual

VPI (Virtual Path Identifier): The virtual path between two points in an ATM
network, and its valid value is from 0 to 255.

VCI (Virtual Channel Identifier): The virtual channel between two points in
an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known
protocols).

Encapsulation Mode: LLC/SNAP-BRIDGING, or VC/MUX

Protocol: You can select the following items from the drop-down list: PPPoE,
DHCP, PPPoA, IPoA, or Bridge.
14
User Manual

PPP Username: The correct user name provided by your ISP.

PPP Password: The correct password provided by your ISP.

Use Static IP Address: If this function is disabled, the modem obtains an IP
address assigned by an uplink equipment such as BAS, through PPPoE
dial-up. If this function is enabled, the modem uses this IP address as the
WAN IP address.

SSID: The service set identification (SSID) is a unique name to identify the
router in the wireless LAN. Wireless stations associating to the router must
have the same SSID. Enter a descriptive name that is used when the
wireless client connecting to the router.
Select Automatic Configuration to display the following page.

PPP Username: The correct user name provided by your ISP.

PPP Password: The correct password provided by your ISP.

SSID: The service set identification (SSID) is a unique name to identify the
router in the wireless LAN. Wireless stations associating to the router must
have the same SSID. Enter a descriptive name that is used when the
wireless client connecting to the router.
After finishing setting, click Apply/Save to save the settings.
15
User Manual
5.2 Advanced Setup
5.2.1 Layer2 Interface
5.2.1.1
ATM Interface
Choose Advanced Setup > Layer2 Interface > ATM Interface . In this page, you
can add or remove to configure DSL ATM Interfaces.
Click Add to add ATM Interface and the following page appears.
16
User Manual
In this page, you can enter this PVC (VPI and VCI) value, and select DSL link type
(EoA is for PPPoE, IPoE, and Bridge.), encapsulation mode, service category.

VPI (Virtual Path Identifier): The virtual path between two points in an ATM
network, and its valid value is from 0 to 255.

VCI (Virtual Channel Identifier): The virtual channel between two points in
an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known
protocols).

DSL Link Type: EoA (it is for PPPoE, IPoE, and Bridge), PPPoA, or IPoA

Encapsulation Mode: LLC/SNAP-BRIDGING, or VC/MUX

Service Category: UBR Without PCR, UBR With PCR, CBR, Non Realtime
VBR, Realtime VBR.
17
User Manual

Select Scheduler for Queues of Equal Precedence as the Default Queue:
Weighted Round Robin or Weighted Fair Queuing.
Click Apply/Save to save the configuration, and return the following page:
If you want to remove this Interface, please select the Remove check box and click
Remove.
5.2.1.2
PTM Interface
Choose Advanced Setup > Layer2 Interface > PTM Interface, and the following
page appears. In this page, you can add or remove to configure PTM WAN
Interfaces.
Click Add and the following page appears.
18
User Manual
In this page, you can select scheduler for queues of equal precedence and enter
the queue value. Click Apply/Save to save configuration.
5.2.1.3
ETH Interface
Choose Advanced Setup > Layer2 Interface > ETH Interface, and the following
page appears. In this page, you can add or remove to configure ETH WAN
Interfaces.
19
User Manual
Click Add and the following page appears.
In this page, you can select a ETH port. Click Apply/Save to save configuration.
Note:
If ETH Interface is selected, there are two WAN service types (PPPoE and
IPoE).
5.2.2
WAN Service
Choose Advanced Setup > WAN Service, and the following page appears.
In this page, you are allowed to add, remove, or edit a WAN service.
Note:
If PTM Interface is selected, there are three WAN service types: PPP over
Ethernet (PPPoE), IP over Ethernet, Bridging. And the corresponding
configurations of PTM WAN service are same as the configurations of ATM
WAN service.
20
User Manual
5.2.2.1 Adding a PPPoE WAN Service
This section describes the steps for adding the PPPoE WAN service.
Step1
In the Wide Area Network (WAN) Service Setup page, click the Add
button to display the following page. (At first, you must add a proper ATM
or PTM interface for this WAN service.)
Step2
In this page, you can select a ATM Interface for the WAN service. After
selecting the ATM interface, click Next to display the following page.
21
User Manual
Step3
In this page, select the WAN service type to be PPP over Ethernet
(PPPoE). Click Next to display the following page.
22
User Manual
Step4
In this page, you can modify the PPP username, PPP password, PPPoE
service name and authentication method.

PPP Username: The correct user name provided by your ISP.

PPP Password: The correct password provided by your ISP.

PPPoE Service Name: If your ISP provides it to you, please enter it. If not,
do not enter any information.

Authentication Method: The value can be AUTO, PAP, CHAP, or MSCHAP.
Usually, you can select AUTO.

Enable Fullcone NAT:. NAT is one where all requests from the same internal
IP address and port are mapped to the same external IP address and port.
Furthermore, any external host can send a packet to the internal host, by
sending a packet to the mapped external address.

Dial on demand (with idle timeout timer): If this function is enabled, you
need to enter the idle timeout time. Within the preset minutes, if the modem
does not detect the flow of the user continuously, the modem automatically
stops the PPPoE connection. Once it detects the flow (like access to a
webpage), the modem restarts the PPPoE dialup. If this function is disabled,
the modem performs PPPoE dial-up all the time. The PPPoE connnection
23
User Manual
does not stop, unless the modem is powered off and DSLAM or uplink
equipment is abnormal.

PPP IP extension: If you want to configure DMZ Host, you should enable it
first.

Use Static IPv4 Address: If this function is disabled, the modem obtains an
IP address assigned by an uplink equipment such as BAS, through PPPoE
dial-up. If this function is enabled, the modem uses this IP address as the
WAN IP address.

Enable PPP Debug Mode:Enable or disable this function.

Bridge PPPoE Frames Between WAN and Local Ports:Enable or disable
this function.

Enable IGMP Multicast Proxy:If you want PPPoE mode to support IPTV,
enable it.
Step5
After setting the parameters, click Next to display the following page.
Step6
In this page, select a preferred WAN interface as the system default
gateway and then click Next to display the following page.
24
User Manual
Step7
In this page, you can obtain the DNS server addresses from the selected
WAN interface. Click Next, and the following page appears.
Step8
In this page, it displays the information about the PPPoE settngs. Click
Apply/Save to save and apply the settings.
5.2.2.2 Adding a Bridge WAN service
This section describes the steps for adding the Bridge WAN service.
Step1
In the Wide Area Network (WAN) Service Setup page, click the Add
button to display the following page. (At first, you must add a proper ATM
25
User Manual
or PTM interface for this WAN service.) Click the Add button to display
the following page.
Step2
Select the proper ATM Interface and then click Next to display the
following page.
26
User Manual
Step3
In this page, you can select the WAN service type, and modify the service
description for this service. After finishing setting, click Next to display the
following page.
27
User Manual
Step4
In this page, it displays the information about the bridge settngs. Click
Apply/Save to save and apply the settings. You can modify the settings
by clicking the Back button if necessary.
5.2.3 3G WAN Service
Choose Advanced Setup > 3G Wan Service , and the following page appears.
This page is used to configure 3G connection. If you want to access the Internet
through 3G connection, a 3G network card is required. Connect the 3G network
card to the USB interface of the Router.

Information: Click it to display the information of the 3G network card.

Upload Driver: For a un-support USB dongle, click it to upload the new
driver for supporting the USB. The driver is a text file.
Click Add in the WAN Service for 3G Mobile Setup to display the following page.
28
User Manual
In this page, you are allowed to configure the settings of the 3G USB modem.

Enable USB Modem: If you want to access the Internet through the 3G
network card, you must enable the USB modem.

User Name: Username provided by your 3G ISP.

Password: Password provided by your 3G ISP.

Authentication Method: Select a proper authentication method in the drop down list. You can select Auto, PAP, CHAP, or MSCHAP.

APN: APN (Access Point Name) is used to identify the service type. Enter
the APN provided by your 3G ISP.


Dial Number: Enter the dial number provided by your 3G ISP.
Idle time (in sec.): If no traffic for the preset time, the 3G will disconnect
automatically.

Dial Delay (in sec.): The 3G delays dial after the DSL is disconnected.

Default WAN Connection Select: You can select DSL or ETHERNET or 3G
from the drop-down list.

WAN back mechanism: The 3G connection is backup for the DSL
connection.
29
User Manual
–
- DSL: If the DSL is disconnected, the 3G starts to dial.
–
- IP connectivity: If the system fails to ping the specified IP
address, the 3G starts to dial.
After finishing setting, click the Apply/Save button to save the settings.
You may also click the Auto Setting button to automatically configure the 3G
connection.
5.3 Wireless
Choose Wireless and the submenus of Wireless are shown as below:
5.3.1 Basic Settings
Choose Wireless > Basic to display the following page. In this page, the figure in
the right area is 2-dimensional code. It includes the wireless SSID and password.
You can obtain the wireless SSID and password through scanning this figure.
30
User Manual
This page allows you to configure the basic features of the wireless LAN interface.

Enable Wireless: Enable or disable the wireless function.

Hide Access Point: if you want to hide any access point for your router,
select this option, and then a station cannot obtain the SSID through the
passive scanning.

Clients Isolation: When many clients connect to the same access point,
they can access each other. If you want to disable the access between the
clients that connect to the same access point, you can select this option.

Disable WMM Advertise: After enabling this option, the transmission
performance multimedia of the voice and video data can be improved.

Enable Wireless Multicast Forwarding (WMF): After enabling this option,
the transmission quality of video service such as IPTV can be improved.

SSID: For the security reason, you should change the default SSID to a
unique name.

BSSID: Display the MAC address of the wireless interface.

Country: The name of the country with which your gateway is configured.
This parameter further specifies your wireless connection. For example, the
channel will adjust according to nations to adapt to each nation's frequency
provision.

Max Clients: Specify the maximum wireless client stations to be enabled to
link with AP. Once the clients exceed the max vlaue, all other clients are
refused. The value of maximum clients is 16.

Wireless - Guest/Virtual Access Points: If you want to make Guest/Virtual
network function be available, you have to check those boxes in the table
below. In the current software version, three virtual access points can be
configured.
After finishing setting, click Apply/Save to save the basic wireless settings and
make the settings take effect.
5.3.2 Security
Choose Wireless > Security to display the following page.
31
User Manual
This page allows you to configure the security features of the wireless LAN
interface. In this page, you can configure the network security settings by the Wi-Fi
Protected Setup (WPS) method or setting the network authentication mode.

WPS Setup
32
User Manual
There are 2 primary methods used in the Wi-Fi Protected Setup:

PIN entry, a mandatory method of setup for all WPS certified devices.
–
Enter STA PIN: If you select it, you need to enter the station PIN from
–
Use AP PIN: The PIN is generated by AP.
client.

Push button configuration (PBC), an actual push button on the hardware or
through a simulated push button in the software. (This is an optional method
on wireless client).
If you are using the PIN method, you will need a Registrar (access point/wireless
router) to initiate the registration between a new device and an active access
point/wireless router. (Note: The PBC method may also need a Registrar when
used in a special case where the PIN is all zeros)
In order to use the push-button for WPS authentication, you must ensure that the
network card support the function. if it supports, you need not to do any
configuration. You can press the WPS button directly to enable the WPS function.
5.4 Voice
Choose Voice and the submenus of Voice are shown as below.
33
User Manual
5.4.1
VoIP Status
Choose Voice > VoIP Status and the Voice Status page appears. In the
Registration Status field, Up means registered successfully, Down means
unregistered, Disable means account is not enabled.
5.4.2
SIP Basic Setting
Choose Voice > SIP Basic Setting, and the following page appears.
34
User Manual
35
User Manual
Figure 7 SIP Basic Setting

Bound Interface Name: you can select the bound interface name from the
drop-down list.

SIP Local Port: Set the SIP local port of the gateway, the default value is
5060. SIP local port is the SIP UA (user agent) port.

SIP domain name: Enter the SIP domain name that you want to set.

Use SIP Proxy: Select the checkbox of Use SIP Proxy, if your DSL router
uses a SIP proxy. SIP proxy allows other parties to call DSL router through it.
When it is selected, the following fields appear.
–
SIP Proxy: The IP address of the proxy.
–
SIP Proxy port: The port that this proxy is listening on. By
default, the port value is 5060.

Use SIP Outbound Proxy: Some network service providers require the use
of an outbound proxy. This is an additional proxy, through which all outgoing
calls are directed. In some cases, the outbound proxy is placed alongside the
firewall and it is the only way to let SIP traffic pass from the internal network
to the Internet. When it is selected, the following fields appear.
–
SIP Outbound Proxy: The IP address of the outbound
proxy.
36
User Manual
–
SIP Outbound Proxy port: The port that the outbound
proxy is listening on. By default, the port value is 5060.

Use SIP Registrar: Select the checkbox of Use SIP Registrar to register
with the proxy. You can register your user ID on the SIP registrar. SIP
registrar works with SIP proxy, allowing other parties to call DSL router
through it. When it is selected, the following fields appear.
–
SIP Registrar: The IP address of the SIP registrar.
–
SIP Registrar port: The port that SIP registrar is listening
on. By default, the port value is 5060.

Account Enabled: If it is unselected, the corresponding account is disabled.
You can not use it to initiate or accept any call.

Polarity Reverse Enable: Enable or disable this function.

Authentication name: Set the user name of authentication.

Password: Set the password of authentication.

Cid Name: User name. It is the Display Name.

Cid Number: Set the caller number. It must be a number of 0~9.

ptime: You can use it to set the packetization time (PT). The PT is the length
of the digital voice segment that each packet holds. The default is 20
millisecond packets. If selecting 10 millisecond, packets improve the voice
quality. Because of the packet loss, less information is lost, but more loads
on the network traffic.

Priority: The priority of codec is declined from up to down. Codecs define the
method of relaying voice data. Different codecs have different characteristics,
such as data compression and voice quality. For Example, G723 is a codec
that uses compression, therefore, it is good for use where the bandwidth is
limited but its voice quality is not good as other codecs, such as the G711. If
you specify none of the codecs, using the default value showed in the above
figure, the DSL router chooses the codec automatically.
After setting, click Apply to take the settings in to effect.
37
User Manual
5.4.3
SIP Advanced Setting
Choose Voice > SIP Advanced Setting, and the following page appears.
38
User Manual
39
User Manual
Figure 8 SIP Advanced Setting

Line: It displays the line you want to configure.

Call waiting:
If call waiting is enabled on a line, you can hear the call waiting tone during a call,
press FLASH on the phone to answer the second call. The first call is automatically
placed on hold. To switch between calls, press FLASH again.
Select Call waiting to enable this feature.
Call forward feature settings (Busy or All) take priority over the call waiting feature.
Call waiting feature is ignored on new incoming calls if there is already a call on
hold or in conference.

Unconditionally Call forwarding number: Enter the number that you want
to set. It is the feature that forwards all incoming calls to an appointed
number unconditionally.

Busy Call forwarding number: Enter the number that you want to set. It is a
feature that forwards all incoming calls to an appointed number when the line
is busy.

No Answer Call forwarding number: Enter the number that you want to set.
It is a feature that forwards all incoming calls to an appointed number when
the call is not answered.

Options Time: Set the time interval for sending the Options message.

Forward unconditionally: Select the check box to enable this function.

Forward on "busy": Select the check box to enable this function.

Forward on "no answer": Select the check box to enable this function.

MWI: When selecting message waiting indicator (MWI), the DSL router
sends a SIP SUBSCRIBE message to the proxy, asking for a notification
when its voicemail status changes. When its status does change, the proxy
send a NOTIFY message to the gateway, causing a MWI tone streamed to
user’s receiver.

Anonymous call blocking
It is a feature that can block the anonymous call.
Select the checkbox of Anonymous call blocking to enable this feature. You can
also dial *77 to enable this feature. Dial *87 to disable this feature.

Anonymous calling
It is a feature that allows using anonymous name as a call number when calling
out.
40
User Manual
Select the checkbox of Anonymous calling to enable this feature. You can also
dial *68 to enable this feature. Dial *82 to disable this feature.

DND
It is a feature to reject all incoming calls.
Select the checkbox of DND to enable this feature. You can also Dial *78 to enable
the feature.


Enable Call Return: Select the check box to enable this function.
Fax Negotiate Mode: You can select it from the drop-down list.

Bypass Codec: You can select it from the drop-down list.

Enable T38 redundancy support: Select the check box to enable this
function.

Enable vbd redundancy support: Select the check box to enable this
function.

RFC2198 Payload Value (range 96~127): Enter the RFC2198 payload
value that the valid range is 96 ~ 127.

Registration Expire Timeout*: Enter the registration expire timeout.

Session Expire Time: The interval of dialog refreshing time.

Min Session Expire Time: The minimum interval of dialog refreshing time.

VoIP DialPlan Setting: Set the VoIP dial plan. If user-dialed number
matches it, the number is processed by the DSL router immediately.

DSCP for SIP: Set the DSCP for SIP. You can select it from the drop-down
list.

DSCP for RTP: Set the DSCP for RTP. You can select it from the drop-down
list.

Dtmf Relay Setting: Set DTMF transmit method, which can be following
values:
–
SIP Info: Use SIP INFO message to transmit DTMF digits.
41
User Manual
–
RFC2833: Use RTP packet to encapsulate DTMF events,
as specified in RFC 2833.
–
InBand: DTMF events are mixed with user voice in RTP
packet.

SIP Transport Protocol: Select the transport protocol to use for SIP
signaling. Note that the SIP proxy and registrar need to support the protocol
you select.

Enable Local Supplementary Service: Select the checkbox to enable the
supplementary service settings by the telephone set. If you deselect the
checkbox, the supplementary service can not be set by the telephone set.
After setting, click Apply to take the settings in to effect.
5.4.4
SIP Extra Setting
Choose Voice > SIP Extra Setting, and the following page appears.

Dial tone time: Dial tone duration.

Busy tone time: Busy tone duration.

Inter digit time: The valid range is 1 ~ 5.

Offhook warning tone time: Offhook warning tone duration.

Ringback tone time: Ringback tone duration.
After setting, click Apply to take the settings in to effect.
5.4.5
SIP Debug Setting
Choose Voice > SIP Debug Setting, and the following page appears.
42
User Manual

Vodsl Console Log Level: Select it from the drop-down list.

SIP Log Server Settings: Set SIP log server IP address and port, then the
log message of the VoIP is sent to the device which IP address you set to. If
you want use this function, both of the IP address and port must be set
correctly.

Gain Settings: Gain is a measure of the ability of a circuit (often an amplifier)
to increase the power or amplitude of a signal. You can increase or decrease
ingress gain and egress gain. The range of the value is from -14 to 6.
5.5 Management
5.5.1 Access Control
Passwords
Choose Management > Access Control > Passwords, and the following page
appears.
43
User Manual
In the page, you can modify the username and password of different users.
After finishing setting, click the Apply/Save button to save and apply the settings.
5.5.2 Update Software
Choose Management > Update Software, and the following page appears.
If you want to upload the software, click the Browse… button to choose the new
software, and then click the Update Software button.
Note:
When software update is in progress, do not shut down the router. After software
update completes, the router automatically reboots.
Please make sure that the new software for updating is correct, and do not use other
software to update the router.
44
User Manual
Q&A
(1)
Q: Why all the indicators are off?
A: Check the following:
 The connection between the power adaptor and the power socket.
 The status of the power switch.
(2)
Q: Why the LAN indicator is off?
A: Check the following:
 The connection between the ADSL router and your computer, hub, or
switch.
 The running status of your PC, hub, or switch.
(3)
Q: Why the DSL indicator is off?
A: Check the connection between the “DSL” port of router and the wall jack.
(4)
Q: Why Internet access fails while the DSL indicator is on?
A: Check whether the VPI, VCI, user name, and password are correctly
entered.
(5)
Q: Why I fail to access the web configuration page of the DSL router?
A: Choose Start > Run from the desktop, and ping 192.168.1.1 (IP address of
the DSL router). If the DSL router is not reachable, check the type of the
network cable, the connection between the DSL router and the PC, and
the TCP/IP configuration of the PC.
(6)
Q: How to load the default settings after incorrect configuration?
A: To restore the factory default settings, turn on the device, and press the
reset button for at least 1 second, and then release it. The default IP
address and the subnet mask of the DSL router are 192.168.1.1 and
255.255.255.0, respectively.
 User/password of super user: admin/admin
 User/password of common user: user/user
45

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : User
Create Date                     : 2012:07:12 10:27:13+08:00
Modify Date                     : 2012:12:13 14:31:45+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : User
Title                           : Microsoft Word - ZHONE 6748_User Manual（优化）.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2012:12:13 14:31:45+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:70c3dbae-f9aa-400e-95d4-c10cb53ac9ac
Instance ID                     : uuid:ab1b8c19-c1ed-48f1-8080-547253f78930
Page Count                      : 51

EXIF Metadata provided by EXIF.tools