DB ELETTRONICA TELECOMUNICAZIONI S P A MOZART500 500W FM BROADCAST TRANSMITTER User Manual Mozart series R1 0 3
DB ELETTRONICA TELECOMUNICAZIONI S.P.A. 500W FM BROADCAST TRANSMITTER Mozart series R1 0 3
User Manual
MOZART Series FM Exciters/Transmitters Userâs Manual Release 1.0.3 - DB ELETTRONICA TELECOMUNICAZIONI S.p.A. - Riviera Maestri del Lavoro, 20/1 - 35127 Z.I. SUD PADOVA ITALY -- Ph. (049) 870-0588 - Fax. (049) 870-0747 - - http://www.dbbroadcast.com - MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 1 /87 The constructor reserves the right to modify the information in this manual at any time without advising update. Document History Rev. 1.0 1.0.1 Date September 2013 October 2013 Name IC IC 1.0.2 1.0.3 October 2013 February 2014 IC AB+DS Details Integration and correction of the menu and technical parameters Complete Series user manual Updated the menu description chapter Issued: February 2014 â Version 1.0.3 Š 2013. Copyright by: DB Elettronica Telecomunicazioni SpA Riviera Maestri del Lavoro, 20/1 35127 Z.I. SUD PADOVA ITALY All rights reserved. All specifications, characteristics and circuit descriptions indicated in this manual are subject to change without notice. MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 2 /87 INDEX GENERAL INFORMATION ................................................................................................................................ 8 1.1 1.2 1.3 1.4 1.5 1.6 SAFETY NOTICES ............................................................................................................................................. 8 FIRST AID IN CASE OF ELECTROCUTION .................................................................................................... 9 WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) ............................................................ 10 MANUFACTURE LABELS .............................................................................................................................. 10 IC RSS-GEN, SEC 7.1.2 WARNING STATEMENT- (REQUIRED FOR TRANSMITTERS) ........................................... 11 IC RSS-102, SEC 2.6 WARNING STATEMENTS .................................................................................................... 11 FM EXCITER GENERAL DESCRIPTION ...................................................................................................... 12 TECHNICAL SPECIFICATIONS ...................................................................................................................... 18 INSTALLATION AND ACTIVATION .............................................................................................................. 21 4.1 4.2 INITIAL CHECK ............................................................................................................................................... 21 CONNECTIONS ................................................................................................................................................ 22 MENU DESCRIPTION ........................................................................................................................................ 23 5.1 VISUALIZATION ............................................................................................................................................. 23 5.1.1 START PAGE ............................................................................................................................................ 23 5.1.2 Main menu ................................................................................................................................................ 23 5.2 VMETERS AND INFO MENU .......................................................................................................................... 24 5.2.1 Output Modulation .................................................................................................................................... 25 5.2.2 Left and Right channels level .................................................................................................................... 25 5.2.3 AES-EBU Left and Right channels level ................................................................................................... 25 5.2.4 Auxiliary channels level ............................................................................................................................ 26 5.2.5 Voltages and current ................................................................................................................................. 26 5.2.6 Heatsink temperature ................................................................................................................................ 27 5.2.7 Device information ................................................................................................................................... 27 5.3 SETTINGS MENU............................................................................................................................................. 28 5.3.1 Frequency Set menu .................................................................................................................................. 29 5.3.2 Power Set menu ........................................................................................................................................ 29 5.3.3 Operative Mode menu ............................................................................................................................... 30 5.3.4 Audio Selection menu................................................................................................................................ 32 5.3.5 Sensitivity menu ........................................................................................................................................ 35 5.3.6 Presetting menu ........................................................................................................................................ 36 5.3.7 Alarms menu ............................................................................................................................................. 43 5.3.8 Memory menu ........................................................................................................................................... 49 5.3.9 History menu ............................................................................................................................................. 53 5.3.10 Generals menu ..................................................................................................................................... 55 FRONT PANEL .................................................................................................................................................... 59 6.1 FRONT PANEL KEYS ...................................................................................................................................... 59 6.2 FRONT PANEL LEDS ...................................................................................................................................... 61 6.2.1 Status leds ................................................................................................................................................. 61 6.2.2 Audio leds ................................................................................................................................................. 62 6.2.3 Control leds............................................................................................................................................... 63 6.2.4 Command leds........................................................................................................................................... 64 REMOTE I/O (OPTIONAL) ............................................................................................................................... 65 WEB SERVER (OPTIONAL) ............................................................................................................................. 66 8.1 WEB PAGES...................................................................................................................................................... 67 8.1.1 Main page ................................................................................................................................................. 67 8.1.2 Login page ................................................................................................................................................ 68 8.1.3 Settings page ............................................................................................................................................. 69 8.1.4 Presettings page ........................................................................................................................................ 70 8.1.5 Log page ................................................................................................................................................... 71 MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 3 /87 8.1.6 Administration page .................................................................................................................................. 72 8.1.7 Modulator Upgrade page ......................................................................................................................... 74 8.1.8 Webserver Upgrade page ......................................................................................................................... 75 8.2 UPGRADING PROCEDURES .......................................................................................................................... 76 8.2.1 Upgrading the modulator firmware .......................................................................................................... 76 8.2.2 Upgrading the webserver board firmware ................................................................................................ 80 8.3 SNMP PROTOCOL ........................................................................................................................................... 84 8.3.1 Management Information Base MIB ......................................................................................................... 84 8.3.2 Message trap and inform .......................................................................................................................... 86 8.3.3 Commands and State................................................................................................................................. 87 MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 4 /87 FIGURES INDEX FIG. 1.1 - UNITS LABEL ..................................................................................................................................................... 10 FIG. 2.1 - MOZART 30 FRONT VIEW ......................................................................................................................... 14 FIG. 2.2 - MOZART 30 REAR VIEW ............................................................................................................................ 15 FIG. 2.3 â MOZART 50/120/300/500/1000 FRONT VIEW .......................................................................................... 16 FIG. 2.4 â MOZART 50/120/300/500/1000 REAR VIEW ............................................................................................. 17 FIG. 5.1 â START PAGE....................................................................................................................................................... 23 FIG. 5.2 â MAIN MENU ....................................................................................................................................................... 23 FIG. 5.3 â VMETERS AND INFO MENUS FLOW GRAPH ......................................................................................................... 24 FIG. 5.4 â OUTPUT TOTAL MODULATION PAGE ................................................................................................................. 25 FIG. 5.5 â ANALOGIC LEFT AND RIGHT INPUT LEVELS ....................................................................................................... 25 FIG. 5.6 â AES-EBU LEFT AND RIGHT INPUT LEVELS ....................................................................................................... 25 FIG. 5.7 â AUXILIARY CHANNELS 1 INPUT LEVELS ............................................................................................................. 26 FIG. 5.8 â AUXILIARY CHANNELS 2 INPUT LEVELS ............................................................................................................. 26 FIG. 5.9 â VOLTAGES AND CURRENT PAGE ........................................................................................................................ 26 FIG. 5.10 â HEATSINK TEMPERATURE PAGE ....................................................................................................................... 27 FIG. 5.11 â DEVICE INFORMATION PAGE ............................................................................................................................ 27 FIG. 5.12 â SETTING MENU FLOW GRAPH ........................................................................................................................... 28 FIG. 5.13 â SET FREQUENCY MENU .................................................................................................................................... 29 FIG. 5.14 â SET POWER MENU ............................................................................................................................................ 29 FIG. 5.15 â OPERATIVE MODE MONO .............................................................................................................................. 30 FIG. 5.16 â OPERATIVE MODE MONO CHANNEL SELECTION ............................................................................................ 30 FIG. 5.17 â OPERATIVE MODE STEREO OPTIONS ............................................................................................................. 31 FIG. 5.18 â OPERATIVE MODE STEREO MPX .................................................................................................................. 31 FIG. 5.19 â AUXILIARY CHANNELS OPTIONS ...................................................................................................................... 32 FIG. 5.20 â AUDIO SELECTION MENU OPTIONS................................................................................................................... 32 FIG. 5.21 â INPUT IMPEDANCE MENU ................................................................................................................................. 33 FIG. 5.22 â PRE-EMPHASIS MENU ....................................................................................................................................... 33 FIG. 5.23 â ENABLE LIMITER MENU ................................................................................................................................... 34 FIG. 5.24 â LIMITER VALUE MENU ..................................................................................................................................... 34 FIG. 5.25 â CHANNELS SENSITIVITY .................................................................................................................................. 35 FIG. 5.26 â PRESETTING MODE........................................................................................................................................... 36 FIG. 5.27 â PRESETTING MONO MODE MENU.................................................................................................................... 37 FIG. 5.28 â PRESETTING STEREO MPX INT MODE MENU ................................................................................................. 38 FIG. 5.29 â PRESETTING TOTAL DEVIATION ADJUSTMENT .................................................................................................. 39 FIG. 5.30 â PRESETTING AUXILIARY CHANNELS DEVIATION ADJUSTMENT ......................................................................... 39 FIG. 5.31 â PRESETTING 19KHZ/MPX OUT MENU............................................................................................................. 40 FIG. 5.32 â PILOT TONE DEVIATION ADJUSTMENT.............................................................................................................. 40 FIG. 5.33 â PILOT TONE PHASE ADJUSTMENT ..................................................................................................................... 41 FIG. 5.34 â AES-EBU INTERFACE ENABLE MENU .............................................................................................................. 41 FIG. 5.35 â AES-EBU RATIO MENU .................................................................................................................................. 42 FIG. 5.36 â ALARMS/WARNINGS MENU FLOW GRAPH ........................................................................................................ 43 FIG. 5.37 â FOLDBACK REFLECTED MENU ......................................................................................................................... 44 FIG. 5.38 â WARNING REFLECTED MENU........................................................................................................................... 44 FIG. 5.39 â WARNING POWER LOW MENU.......................................................................................................................... 45 FIG. 5.40 â ALARM POWER LOW MENU.............................................................................................................................. 46 FIG. 5.41 â AUDIO LOW LEVEL MENU ............................................................................................................................... 46 FIG. 5.42 â AUDIO LOW TIMEOUT MENUS .......................................................................................................................... 47 FIG. 5.43 â AUDIO OVER LEVEL MENU .............................................................................................................................. 47 FIG. 5.44 â AUDIO OVER TIMEOUT MENUS ........................................................................................................................ 48 FIG. 5.45 â AUDIO EVENTS TYPE MENU.............................................................................................................................. 48 FIG. 5.46 â MEMORY MENU FLOW GRAPH .......................................................................................................................... 49 FIG. 5.47 â ACTIVE MEMORY MENU .................................................................................................................................. 50 FIG. 5.48 â EDIT MEMORY MENUS ..................................................................................................................................... 50 FIG. 5.49 â ENABLE MEMORY EDITING PAGE ..................................................................................................................... 51 FIG. 5.50 â ENDING EDITING MEMORY PAGE .................................................................................................................... 51 FIG. 5.51 - MEMORY MENU DURING EDITING ..................................................................................................................... 51 FIG. 5.52 â CONFIRMATION EDITING MEMORY PAGE ......................................................................................................... 51 MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 5 /87 FIG. 5.53 â CLEAR ALL MEMORY MENU ............................................................................................................................ 52 FIG. 5.54 â CLEAR ALL MEMORY CONFIRMATION PAGE .................................................................................................... 52 FIG. 5.55 â HISTORY MENU ................................................................................................................................................ 53 FIG. 5.56 â HISTORY MENU EVENT DETAIL PAGE ............................................................................................................... 53 FIG. 5.57 â GENERALS MENU FLOW GRAPH........................................................................................................................ 55 FIG. 5.58 â SET HOUR PAGE ............................................................................................................................................... 56 FIG. 5.59 â SET MINUTE PAGE ............................................................................................................................................ 56 FIG. 5.60 â SET SECOND PAGE............................................................................................................................................ 56 FIG. 5.61 â SET DAY PAGE ................................................................................................................................................. 57 FIG. 5.62 â SET MONTH PAGE............................................................................................................................................. 57 FIG. 5.63 â SET YEAR PAGE................................................................................................................................................ 57 FIG. 5.64 â SET RS-485 ADDRESS PAGE ............................................................................................................................. 58 FIG. 5.65 â UNIT IP ADDRESS PAGE ................................................................................................................................... 58 FIG. 5.66 â UNIT NETMASK PAGE ....................................................................................................................................... 58 FIG. 8.1 â WEBSERVER MAIN PAGE .................................................................................................................................... 67 FIG. 8.2 â WEBSERVER LOGIN PAGE .................................................................................................................................. 68 FIG. 8.3 â WEBSERVER SETTING PAGE ............................................................................................................................... 69 FIG. 8.4 â WEBSERVER PRESETTING PAGE ......................................................................................................................... 70 FIG. 8.5 â WEBSERVER LOG PAGE ..................................................................................................................................... 71 FIG. 8.6 â WEBSERVER ADMINISTRATION PAGE ................................................................................................................ 72 FIG. 8.7 â WEBSERVER MODULATOR UPGRADE PAGE ....................................................................................................... 74 FIG. 8.8 â WEBSERVER UPGRADE PAGE ............................................................................................................................. 75 FIG. 8.9 â START IN BOOTLOADER MODE ........................................................................................................................... 76 FIG. 8.10 â MODULATOR UPGRADE PAGE .......................................................................................................................... 76 FIG. 8.11 â NEW FIRMWARE SELECTION ............................................................................................................................ 77 FIG. 8.12 â UPLOAD THE NEW FIRMWARE .......................................................................................................................... 77 FIG. 8.13 â CONFIRM THE UPLOAD..................................................................................................................................... 77 FIG. 8.14 â UPGRADE TO THE NEW FIRMWARE ................................................................................................................... 78 FIG. 8.15 â ERASE THE FLASH BEFORE THE UPGRADE ........................................................................................................ 78 FIG. 8.16 â UPGRADE IN WORKING .................................................................................................................................... 78 FIG. 8.17 â UPGRADE COMPLETE ....................................................................................................................................... 79 FIG. 8.18 â WEBSERVER UPGRADE PAGE ........................................................................................................................... 80 FIG. 8.19 â SELECT THE NEW WEBSERVER BOARD FIRMWARE ........................................................................................... 80 FIG. 8.20 â UPLOAD THE FIRMWARE TO WEBSERVER ......................................................................................................... 81 FIG. 8.21 â CONFIRM THE UPLOADING ............................................................................................................................... 81 FIG. 8.22 â BUSY STATE DURING UPLOAD PROCEDURE ...................................................................................................... 81 FIG. 8.23 â NEW FIRMWARE READY TO UPGRADE .............................................................................................................. 82 FIG. 8.24 â CONFIRMATIONS TO UPGRADE ......................................................................................................................... 82 FIG. 8.25 â UPGRADE IN WORKING .................................................................................................................................... 82 FIG. 8.26 â REBOOT THE WEBSERVER ................................................................................................................................ 83 FIG. 8.27 â CONFIRM THE REBOOT ..................................................................................................................................... 83 FIG. 8.28 â WAIT UNTIL THE REBOOT IS COMPLETED ......................................................................................................... 83 FIG. 8.29 â LIST OF FILE OF MIB PACKET .......................................................................................................................... 84 FIG. 8.30 â FM SINGLE TRANSMITTER MIB ...................................................................................................................... 85 FIG. 8.31 - TRAPS AND INFORMS CONFIGURATION ............................................................................................................. 86 MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 6 /87 TABLES INDEX TABLE 5.1 â FREQUENCY PERMITTED VALUES................................................................................................................... 29 TABLE 5.2 â SETTING POWER SPECIFICS ............................................................................................................................ 30 TABLE 5.3 â IMPEDANCE PERMITTED VALUES ................................................................................................................... 33 TABLE 5.4 â PRE-EMPHASIS PERMITTED VALUES ............................................................................................................... 33 TABLE 5.5 â LIMITER PERMITTED VALUES ......................................................................................................................... 34 TABLE 5.6 â SENSITIVITY PERMITTED VALUES .................................................................................................................. 35 TABLE 5.7 - PRESETTING STEREO MPX EXT MODE MENU .............................................................................................. 38 TABLE 5.8 â TOTAL DEVIATION ADJUSTMENT PERMITTED VALUES ................................................................................... 39 TABLE 5.9 â AUXILIARY CHANNELS DEVIATION ADJUSTMENT PERMITTED VALUE ............................................................ 39 TABLE 5.10 â PILOT TONE DEVIATION ADJUSTMENT PERMITTED VALUES.......................................................................... 40 TABLE 5.11 â PILOT TONE PHASE ADJUSTMENT PERMITTED VALUES ................................................................................. 41 TABLE 5.12 â AES-EBU RATIO PERMITTED VALUES ........................................................................................................ 42 TABLE 5.13 â FOLDBACK REFLECTED PERMITTED VALUES ............................................................................................... 44 TABLE 5.14 â WARNING REFLECTED PERMITTED VALUES ................................................................................................. 45 TABLE 5.15 â WARNING POWER LOW PERMITTED VALUES................................................................................................ 45 TABLE 5.16 â ALARM POWER LOW PERMITTED VALUES .................................................................................................... 46 TABLE 5.17 â AUDIO LOW LEVEL PERMITTED VALUES ..................................................................................................... 47 TABLE 5.18 â AUDIO LOW TIMEOUTS PERMITTED VALUES ................................................................................................ 47 TABLE 5.19 â AUDIO OVER LEVEL PERMITTED VALUES .................................................................................................... 48 TABLE 5.20 â AUDIO OVER TIMEOUTS PERMITTED VALUES .............................................................................................. 48 TABLE 5.21 â AUDIO EVENTS PERMITTED TYPES ............................................................................................................... 49 TABLE 5.22 â MEMORY AVAILABLE .................................................................................................................................. 50 TABLE 5.23 â EVENTS LIST ................................................................................................................................................ 54 TABLE 7.1 â REMOTE I/O PINOUT ...................................................................................................................................... 65 TABLE 8.1 â TRAPS AND INFORMS AVAILABLE .................................................................................................................. 86 MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 7 /87 1 GENERAL INFORMATION 1.1 SAFETY NOTICES To avoid risks of electrical shocks or fire, only qualified personnel should execute the procedures specified in this manual. When the protective covers of any device or component connected to a 110 / 240 VAC source by a power cord are removed, voltages and currents dangerous to life may be exposed. Contact with 110 / 240 Volts of alternating current and associated direct current and voltages can be fatal. CAUTION To reduce the risks of electrical shock, do not remove the cover (or the back). Refer, for servicing, to qualified service personnel. This installation should be done by a qualified person and should comply with to all local applicable laws. Beryllium Oxide It is dangerous component if inhaled, eaten or put into direct contact with skin, especially if the skin is cut or wounded. Special care is required in handling beryllium material in order to NOT produce any dust, particles, fumes etc. etc. Whenever beryllium material is broken it is extremely important to collect all parts in a carefully sealed and marked container for discharging in a specific way through controlled channels. All above operations have to be affected using gloves and tongs, with special care taken not to produce dust. After handling beryllium components it is essential to wash hands carefully. Beryllium compounds are used in RF Connectors. MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 8 /87 1.2 FIRST AID IN CASE OF ELECTROCUTION Do not touch the victim until the electrical circuit has been interrupted to make sure the person is isolated. If this is not possible, move the victim away from the conductor by using insulated material. If respiration is interrupted, artificial respiration must be applied (mouth-to-mouth respiration). Lay the patient on his back, feet elevated above the level of the head, chin up and head back. Call a doctor urgently In case of a mouth wound it may be necessary to apply mouth-to-nose respiration, blocking the patientâs mouth. In case of face wounds the need for manual artificial respiration may arise. Push down on the chest of the prostrate patient whilst moving the patientâs arms up and out. If the victim has also suffered burns then, without obstructing breathing, proceed as follows: ⢠Do not remove clothing from burn wounds. ⢠If possible gently pour cold water over wounds to relieve pain. ⢠Do not use any medication. ⢠Call for urgent medical assistance. MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 9 /87 1.3 WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) The purpose of the DIRECTIVE 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE) is, as first priority, the prevention of waste electrical and electronic equipment and, in addition, the reuse, recycling and other forms of recovery of such wastes so as to reduce the disposal of waste. To do this, remember to collect separately all the electronic material. 1.4 MANUFACTURE LABELS All the units are identified by a black silver label: Fig. 1.1 - Units Label Label fields: 1. Product name This field contains the model of the unit (part name). 2. Serial number This field contains the serial number of the module or equipment (made by 8 digits). 3. Operating Frequency This field contains the operating frequency (for FM units) or the channel and standard (for TV units) set by the factory. In case no indication is present, the unit is considered as broadband in its operating band. 4. Return Loss FACTORY USE ONLY MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 10 /87 5. Functional Test A cross on this field indicates that the functional test of the unit has been done by the technician. 6. Mechanical Test A cross on this field indicates that the functional test of the unit has been done by the technician. 7. Temp. Test A cross on this field indicates that the functional test of the unit has been done by the technician. 1.5 5)(;32685(6TATEMENT6 $QWHQQDVIRUEURDGFDVWWUDQVPLWWHUVVKRXOGEHPRXQWHGRQRXWGRRUSHUPDQHQWVWUXFWXUHV 7KH)&&DVVHVVHV5)H[SRVXUHLVVXHVDWWKHWLPHRIOLFHQVLQJRI\RXUVWDWLRQZLWKWKHUHTXLUHG )&&%XUHDX V DQGWKLVZLOOLQFOXGHDQWHQQDFRORFDWLRQLVVXHVDVUHTXLUHGLQ E 6LPLODUO\&DQDGDZLOODOVRDVVHVV5)H[SRVXUHDWWKHWLPHWKHVWDWLRQLVOLFHQVHG MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 11 /87 2 FM EXCITER GENERAL DESCRIPTION The MOZART FM exciter/transmitter is the result of the development of the MSE (Magnetic Sound Enhancer) technology together with the improvements in the FM modulation and using high performances PFC filters for the AC/DC conversion. This unit is ideal as stand alone unit for low power transmissions or suitable as high performance exciter in modular transmitters. This unit has been developed with the Green RF technology which increases the efficiency of the amplification part reducing the dimensions and power consumption without modifying the quality of the transmission. The main advantages of this technology are: - High RF efficiency - Lower heating (lower necessity of air conditioning in the installation room) - Higher devices safety - Higher total reliability - Lower AC power consumption An user friendly interface with the combination of leds and LCD display offers a very easy method to control the MOZART main parameters with a metering accuracy that helps the user to install the unit and check its status even in case he doesnât have expensive test equipments. In case of fault of the unit or antenna system, the protection system lowers automatically the output power, in order to bring back the operating conditions to a safe area without causing a system shut down, and it indicates on the front panel display the alarm message. The protection system reduces or stops the output power in case of: - V.S.W.R. too high. - Heatsink temperature too high or cooling stop (OVER HEAT). - Missing Enable command (in case of combination with external units like control logic units) MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 12 /87 The switch-mode power supply is largely oversized and guarantees a regular operation even in the presence of wide main voltage fluctuations. The systems cooling grants a safe operation even in hard climatic conditions. MOZART SERIES âFM Exciters/Transmitters - USERâS MANUAL 13 /87 Fig. 2.1 - MOZART 30 FRONT VIEW 1. RF Monitor connector 2. Status leds a. ALARM: in case of a temporary alarm (it returns automatically to the normal status at next attempt of the unit) â RED led b. WARNING: in case of a warning is present - YELLOW led c. ON: in case the unit is connected to the mains and switched on â GREEN led 3. LCD Display 4. Navigation keys (UP /DOWN / RIGHT / LEFT / OK) 5. Escape key 6. AUDIO and CONTROL leds a. RDS/AUX: it is ON in case the RDS/SCA/AUX are on b. MPX: it is ON in case the MPX EXT mode is selected c. NO AUDIO: it is ON in case of alarm/warning on audio signal d. AES-EBU: it is ON in case the AES-EBU is on e. LIM: it is ON in case the limiter is set to on f. STEREO: it is ON in case the MPX INT mode is selected g. PRE EMPH: it is ON in case the pre-emphasis is on h. MONO: it is ON in case the MONO mode is selected i. PREF: no actually available j. PLL LOCK: it is ON in case the PLL is correctly locked k. AUTO: no actually available l. INTLK: it is ON in case the ENABLE is closed 7. Command keys (Reset Alarms, Local/Remote, ON/OFF) and leds (Fault, Local, RF ON) 14 /87 Fig. 2.2 - MOZART 30 REAR VIEW 1. 2. 3. 4. 5. 6. 7. 8. 9. AC input LAN port Cooling FAN RF output connector (N) Left XLR connector Right XLR connector AES/EBU XLR connector 19kHz / MPX OUT BNC connector AUX BNC connector 10 12 11 13 15 14 16 17 10. MOD OUT BNC connector 11. SCA BNC connector 12. MPX BNC connector 13. RDS BNC connector 14. ENABLE connector 15. RS 485 MASTER connector 16. RS 485 SLAVE connector 17. REMOTE connector 15 /87 Fig. 2.3 â MOZART 50/120/300/500/1000 FRONT VIEW 1. RF Monitor connector 2. Status leds a. ALARM: in case of a temporary alarm (it returns automatically to the normal status at next attempt of the unit) â RED led b. WARNING: in case of a warning is present - YELLOW led c. ON: in case the unit is connected to the mains and switched on â GREEN led 3. LCD Display 4. Navigation keys (UP / DOWN / RIGHT / LEFT / OK) 5. ESCAPE key 6. AUDIO and CONTROL leds a. RDS/AUX: it is ON in case the RDS/SCA/AUX are on b. MPX: it is ON in case the MPX EXT mode is selected c. NO AUDIO: it is ON in case of alarm/warning on audio signal d. AES-EBU: it is ON in case the AES-EBU is on e. LIM: it is ON in case the limiter is set to on f. STEREO: it is ON in case the MPX INT mode is selected g. PRE EMPH: it is ON in case the pre-emphasis is on h. MONO: it is ON in case the MONO mode is selected i. PREF: no actually available j. PLL LOCK: it is ON in case the PLL is correctly locked k. AUTO: no actually available l. INTLK: it is ON in case the ENABLE is closed 7. Command keys (Reset Alarms, Local/Remote, ON/OFF) and leds (Fault, Local, RF ON) 16 /87 Fig. 2.4 â MOZART 50/120/300/500/1000 REAR VIEW 18 19 17 13 11 12 10 1. 2. 3. 4. 5. 6. 7. 8. 9. AC input LAN port Cooling FAN RF output connector (N) Left XLR connector Right XLR connector AES/EBU XLR connector 19kHz / MPX OUT BNC connector AUX BNC connector 16 15 14 10. MOD OUT BNC connector 11. SCA BNC connector 12. MPX BNC connector 13. RDS BNC connector 14. ENABLE connector 15. RS 485 MASTER connector 16. RS 485 SLAVE connector 17. REMOTE connector 18. Fuse 19. Switching on button 17 /87 3 TECHNICAL SPECIFICATIONS RF FEATURES RF Output impedance Frequency range Frequency control Off-lock attenuation Type of modulation Modulation mode Frequency deviation Reference Constancy of freq. dev. Variation of freq. Short term stability Instantaneous BW RF harmonics RF spurious Pre-emphasis Pre-emphasis precision Stereo operation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Audio response Audio filter attenuation Common mode rejection Stereo Separation Crosstalk attenuation (M / S) Spurious products 38 kHz suppression Subcarrier frequency Subcarrier generation Pilot frequency THD+N on encoded channels Nominal pilot deviation Audio response THD+N on encoded channels 50⌠unbalanced 87.5 to 108 MHz Synthesizer Âľprocessor controlled > 75 dBc (typical -80 dB) F3E / F8E direct FM at the carrier frequency Mono, Stereo, Multiplex, SCA, RDS, AUX (input selected by front panel) Âą75 kHz =100 %, Âą150 kHz capability (others on request) VCTCXO 10 MHz Âą 1ppm or 10 MHz external (Optional) Âą1 % over six months Âą 1ppm/year Âą 1 ppm from -5 to +45 °C >20 MHz Exceeds EBU/CCIR/FCC requirements > -75dBc Exceeds EBU/CCIR/FCC requirements < -100 dBc @ Âą 1 MHz min. out of carrier (typical -110dB) Flat/50/75Âľs selectable via front panel Nominal 1% (typical 0.4% ) CCIR 450/S2 "pilot tone system" STEREO OPERATION Âą0.3 dB da 20 Hz to 15 kHz > 55 dB @ 19 kHz, >45dB 19 to 100kHz 20 Hz to 15 kHz > 45 dB 30-80Hz >53dB (typ. 56), 80Hz-15kHz >60 dB (typ.70) > 40 dB 30 Hz to 15 kHz (typ. 52dB / 400Hz to 5kHz) > 53 kHz > 50 dB > 70 dB (Typ -85dB) 38 kHz Âą 2 Hz Internal crystal 19 kHz Âą 1 Hz < 0.03 % 30 Hz TO 15 kHz ( typ -75dB) Âą7 kHz MONO OPERATION Âą0.3 dB 20 Hz to 15 kHz (+0/-2%) 30 Hz to 15 kHz < 0.06% ( typ. 0.03 % ) typ. -78dB 18 /87 MPX OPERATION (External coder) 30Hz - 100kHz Âą 0.15 dB Audio response THD+N on encoded channels 30 Hz to 15 kHz < 0.03% ( typ. 0.02% , < -75dB) AUDIO INPUTS Function Composite SCA/RDS/AUX AES/EBU Input level / Adjustment range -0 á +15 dBu BW Âą0.15 dB 30 Hzá100kHz Âą0.15 dB 40kHzá100kHz -16 á 0 dBu -3 dBFS for Âą 75 kHz 15 dBu (12.33 Vpp) -15 ⌠0 dBFS 0 to 15 dBu (2.19 Vpp to 12.3 Vpp) -0 á +15 dBu -0 á +15 dBu RF connector Monitor RF output Pilot/MPX Mod. Output Impedance Type Conn. N° >5 k⌠Unbal. BNC on Unbal. BNC ~2 k⌠(other request) 0.15 dB 40kHzá100kHz 110 ⌠Unbal XLR Âą0.15 dB 30Hzá15kHz 10 k⌠600 ⌠Unbal. Bal. XLR Âą0.15 dB 30Hzá15kHz 10 k⌠600 ⌠Unbal. Bal. XLR AUDIO OUTPUTS N female -44dBcÂą2dB from 87.5 to 108 MHz BNC connector 19 kHz or MPX, level 1 Vpp, internally adjustable BNC Connector MODEL NOMINAL POWER CONNECTOR SIZE MOZART 30 30 W 1U x 19â MOZART 50 50 W 1U x 19â MOZART 120 120 W 2 U x 19â MOZART 300 300 W 2 U x 19â MOZART 500 500 W 2 U x 19â MOZART 1000 1000 W DIN 7/16 2 U x 19â 19 /87 Storage temperature Operating temperature Guaranteed performance temperature Relative non-condensing humidity Max operating altitude Max extraneous field strength Power supply Display Cooling ENVIRONMENT -20°C TO + 60 °C 0 °C TO + 50 °C 0 °C TO + 45 °C 90 % MA 3000 mt. â¤10 V/m; ⤠4 A/m SIZE & ELECTRICS 110/220V single phase AC (+10 / -15 %) 50-60Hz/ Âą 5% Blue back panel; 2 raw 24 character LCD Forced air, with external long life brushless ball bearing fan Features and specifications subject to change without notice. 20 /87 4 INSTALLATION AND ACTIVATION 4.1 INITIAL CHECK The equipment becomes the property of the customer when the equipment is delivered to the carrier. Carefully unpack the transmitter. Perform a visual inspection to determine that no apparent damage has been incurred during shipment. All shipping materials should be retained until it is determined that the unit has not been damaged. Claims for damaged equipment must be promptly filed with the carrier or the carrier may not accept the claim. The contents of the shipment should be as indicated on the packing list. If the contents are incomplete, or if the unit is damaged electrically or mechanically, notify both the carrier and the supplier. CAUTION: Before switch the equipment on, ensure that all RF Loads, RF cables and connectors are properly connected. To prevent damage to the amplifiers, it is essential that either the feeder and antenna system or the dummy load have a good in band return loss. Failure to observe the above caution and also the installation instructions of this amplifier may cause damages to the amplifiers for which the supplier cannot be considered responsible. PREVENTION OF ACCIDENTS When it is used in normal applications and within the parameters defined in the technical specifications, this equipment does not endanger health and safety, provided that normal operating and engineering safety practices are observed and that it is used only by authorized, trained and qualified personnel. THERMIC AND ENVIRONMENTAL CONDITIONS - A too high environmental temperature (in any case not higher than 45°C) shall cause a nonadequate rack cooling putting the equipment in hard working conditions. - An air conditioner should be installed to keep the room temperature constant even in case of external temperature variation. 21 /87 4.2 CONNECTIONS Install the transmitter so that the space over and under the equipment is sufficient for the cooling air to flow through. Before installing the equipment always make sure that the transmitter is not powered. This has the purpose to prevent electrical shocks to the operators and damage to the equipment. Before carrying out any other electrical connection, connect the rack to the station ground. Connect the transmitting antenna cable or the cable related to the connection of the output filter to the output connector of the unit (in the latest case connect the output of the filter to the transmitting antenna) using a 50 Ohms coaxial cable. In case the transmitter is not connected to an external control unit, check that the ENABLE connector on the back panel is correctly inserted. Connect the power cord to an operating source. Make sure that the power supply source provides the nominal voltage prescribed. Note: the unit is designed to operate with the nominal voltage Âą15%. We suggest the installation of spike suppressors, line conditioners, isolation transformers, AVR and/or UPS or other devices useful to protect the equipment from eventual damages that can be caused by the mains fluctuations. 22 /87 5 MENU DESCRIPTION 5.1 VISUALIZATION The following pages are related to parameters that are visualized on the front panel: they are indications of the actual operating parameters of the unit. 5.1.1 START PAGE After the unit power on, the first page in the display shows information about the internal hardware revision and supplier (first row), and about firmware revision and unit model (second row). Fig. 5.1 â Start page The page remains active for a few seconds before moving to the main menu. 5.1.2 MAIN MENU This is the default page and it indicates the output power set by the customer (SET), the transmission frequency in MHz, the real forward power in Watt (that can be different from SET in case of an alarm, warning, failure or in case the unit is in OFF state), and the reflected power in Watt. Fig. 5.2 â Main menu The unit moves to this page in case no key is pressed for 60 seconds. 23 /87 5.2 VMETERS AND INFO MENU In these menus it is possible to find the levels of the input channels, the internal voltages, currents, temperatures and the software/hardware revisions. In the Main Menu page press DOWN key to enter these pages and UP and DOWN keys to navigate in the sub-menus. [0] Main Page [1] Output Modulation [2] Left and Right channels input level [3] Left and Right AES-EBU channels input level [4] MPX External, RDS External input levels [5] SCA and AUX input levels [6] Internal voltages and current [7] Heatsink temperature [8] Device information Fig. 5.3 â Vmeters and Info menus flow graph 24 /87 5.2.1 OUTPUT MODULATION In this page the Total Output modulation level is indicated in KHz. Fig. 5.4 â Output Total Modulation page Pressing the UP or DOWN buttons you can move inside this menu and see the different pages indicated here below. 5.2.2 LEFT AND RIGHT CHANNELS LEVEL In this page the analogic Left and Right channels levels are indicated in dBu. Fig. 5.5 â Analogic Left and Right input levels 5.2.3 AES-EBU LEFT AND RIGHT CHANNELS LEVEL Pressing the DOWN button you can see the Left and Right levels for the AES-EBU input channels indicated in dBFS. Fig. 5.6 â AES-EBU Left and Right input levels 25 /87 5.2.4 AUXILIARY CHANNELS LEVEL Pressing the DOWN button you can see the MPX External and RDS External levels indicated in dBu. Fig. 5.7 â Auxiliary channels 1 input levels Pressing the DOWN button you can see the SCA and AUX levels indicated in dBu. Fig. 5.8 â Auxiliary channels 2 input levels 5.2.5 VOLTAGES AND CURRENT This page allows the visualization of the unit analogic working values: VPA = voltage that supplies the RF module in Volt. IPA = current absorbed by the RF module in Ampere. VPu = Main power supply voltage in Volt. VT = Voltage Tuning (VCO working voltage) in Volt. Fig. 5.9 â Voltages and Current page 26 /87 5.2.6 HEATSINK TEMPERATURE This page allows the visualization of the RF heatsink temperature in Celsius degrees. Fig. 5.10 â Heatsink temperature page 5.2.7 DEVICE INFORMATION This page allows the visualization of device model, manufacturer name, hardware and firmware revisions. Fig. 5.11 â Device information page 27 /87 5.3 SETTINGS MENU The following pages are related to the unit main parameters. To navigate on Setting menu press LEFT or RIGHT key from Main Menu. In case sub-menu is present, an arrow pointing downwards will be showed in the second row on the right, press DOWN or UP to navigate on sub-menus. [0] Main Menu [1] Frequency [2] Setting Power [3] Operative Mode [4] Audio Selection [5] Sensitivity Set [6] Presettings [7] Alarms/Warnings [8] Memory Manage [9] History Log [10] Generals Fig. 5.12 â Setting menu flow graph 28 /87 5.3.1 FREQUENCY SET MENU Press the LEFT or RIGHT keys to access the slide to program the frequency. Push the OK key to enter the menu (a blinking arrow will be showed in the second row on the right), press UP key to increase or DOWN key to decrease the frequency value. Confirm the new value pressing the OK key or ESC key to exit without saving. During the frequency change the PLL LOCK led will be switched off until the PLL will be locked to the new frequency. Fig. 5.13 â Set frequency menu MIN value: 87.50 MHz MAX value: 108.00 MHz STEP: Âą0.01MHz Table 5.1 â Frequency permitted values 5.3.2 POWER SET MENU To program the RF Power output in Watt, press the LEFT or RIGHT key up to arrive to the slide here below. Press the OK key to enter the program mode (blinking arrow in second row on the right). In the first row the forward power value indicates the actual output power, in the second row the Set Pout is the value that the customer is setting. Fig. 5.14 â Set power menu The value can be modified pressing UP and DOWN keys to increase or decrease the value. Confirm new value and exit routine pressing the OK button or press ESC key to exit without saving. The new power value is applied in real time. 29 /87 NOMINAL POWER MIN POWER MAX POWER STEP 30 W 0W 30 W 0.1 W 50 W 0W 60 W 1W 120 W 0W 150 W 1W 300 W 0W 330 W 1W 500 W 0W 550 W 10 W 1000 W 0W 1100 W 10 W Table 5.2 â Setting power specifics 5.3.3 OPERATIVE MODE MENU In the Operative Mode menu is possible activate/deactivate the various input channels depending on the configuration MONO/STEREO in the Presettings Menu. 5.3.3.1 MONO ACTIVE In case the MONO is active, the page in the Operative Mode menu will be the one here below: Fig. 5.15 â Operative Mode MONO Starting condition in case the configuration is changed from STEREO to MONO is always OFF. To activate the desired channel press the OK key to enter the program mode (blinking arrow in second row on the right). To select Left or Right channel press UP or DOWN keys, press OK key to confirm the channel selected or ESC key to exit routine without saving. Fig. 5.16 â Operative Mode MONO channel selection 30 /87 In case the AES-EBU is active (Presetting Menu), the enabled channel is relative to AES-EBU, please select AES-EBU:Off for using the analogic input channels. 5.3.3.2 STEREO ACTIVE In case the STEREO is active, in the Operative Mode is present a sub menu due to the possibilities to activate the auxiliary channels: [0] STEREO selection [1] Auxiliary channel RDS [2] Auxiliary channel SCA [3] Auxiliary channel AUX Fig. 5.17 â Operative Mode STEREO options Starting condition for STEREO selection and auxiliary channels, in case the mode is changed from MONO to STEREO, is always OFF. In the STEREO selection can be selected the MPX External (rear connector) or the MPX Internal (if Stereo Coder card is available) mode. Fig. 5.18 â Operative Mode STEREO MPX To activate the desired mode press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select the desired mode. Press OK key to confirm or ESC key to exit routine without saving. 31 /87 5.3.3.3 AUXILIARY CHANNELS To enable the auxiliary channels (available only in STEREO mode) navigate in the sub-menu with the UP and DOWN keys until the channel desired and press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to change the ON/OFF state. Press OK key to confirm or ESC key to exit routine without saving. Fig. 5.19 â Auxiliary channels options In case one auxiliary channel is enabled the led RDS/AUX in the frontal panel will be switched on. 5.3.4 AUDIO SELECTION MENU In the Audio Selection sub-menu the regulations of input impedance, pre-emphasis and limiter are available. To navigate in the sub-menu press UP or DOWN keys. [0] Input Impedance [1] Preemphasis [2] Limiter [3] Limiter Value Fig. 5.20 â Audio Selection menu options 32 /87 5.3.4.1 INPUT IMPEDANCE In this sub-menu the impedance of analogic Left and Right channels can be selected. Fig. 5.21 â Input Impedance menu To change the input impedance, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select the impedance value. Press OK key to confirm or ESC key to exit routine without saving. Impedance value: 600, 10K Table 5.3 â Impedance permitted values 5.3.4.2 PRE-EMPHASIS REGULATION In this sub-menu pre-emphasis value can be changed. Fig. 5.22 â Pre-emphasis menu To change the pre-emphasis value, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select the new value. Press OK key to confirm or ESC key to exit routine without saving. Pre-emphasis values: Linear, 50us, 75us Table 5.4 â Pre-emphasis permitted values In case the pre-emphasis is set different from Linear the led PRE EMPH on the frontal panel will be switched on. 33 /87 5.3.4.3 LIMITER REGULATION In these sub-menus an upper limit for the output signal deviation can be enabled and regulated. The menu Limiter permits to enable or disable the limiter, if the limiter is enabled the value can be regulated in the next menu. Fig. 5.23 â Enable limiter menu To enable/disable the limiter press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select the on/off state. Press OK key to confirm or ESC key to exit routine without saving. In case the Limiter is enabled the green led LIM on the frontal panel will switched on. To adjust the limiter value, press DOWN key to select the Limiter value sub-menu. Fig. 5.24 â Limiter value menu To change the limiter value, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select the new value. Press OK key to confirm or ESC key to exit routine without saving. The limiter value is applied in real time and only if the limiter is enabled. MIN value: 30 KHz MAX value: 180 KHz STEP: Âą1 KHz Table 5.5 â Limiter permitted values 34 /87 5.3.5 SENSITIVITY MENU In this menu it is possible to set the sensitivity value in of all available unit input channels, the sensitivity level will induce a regulation of channels internal attenuators. A sensitivity value equal to the relative channel input level will cause an output signal deviation of 75 KHz in case of mono signal or 71 KHz in case of stereo signal. To navigate in this sub-menu press UP or DOWN keys until the channel desired. Fig. 5.25 â Channels Sensitivity To change the sensitivity level, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to increase or decrease the value. Press OK key to confirm or ESC key to exit routine without saving. The sensitivity value is applied in real time and only if the relative channel is in ON state (see menu Operat.Mode). CHANNELS MIN value MAX value STEP LEFT, RIGHT 0 dBu +15 dBu Âą0.05 dB AES-EBU LEFT, RIGHT -10 dBFS 0 dBFS Âą0.05 dB MPX Ext 0 dBu +15 dBu Âą0.05 dB RDS, SCA, AUX -16 dBu 0 dBu Âą0.5 dB Table 5.6 â Sensitivity permitted values 35 /87 5.3.6 PRESETTING MENU In this menu it is possible to set the other main parameters of the unit: MONO/STEREO mode, channels deviation offset, pilot tone frequency and phase shift, AES-EBU and MPX/19KHz Out. The menu layout is different depending on MONO, STEREO (MPX Int or MPX Ext) mode. 5.3.6.1 MODE: MONO/STEREO To change the operational mode, select the first entry in the Presettings menu and press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select MONO or STEREO. Press OK key to confirm or ESC key to exit routine without saving. Fig. 5.26 â Presetting mode Note: Now in the menu Operat.Mode the channels or the configuration MPX Internal/MPX External (in case of STEREO mode) have to be activated. Every change from MONO-to-STEREO or STEREO-to-MONO will set the channels and the MPX Int/Ext in OFF state so the configuration has to be set again in the menu Operat.Mode. If MONO mode is enabled the led MONO in the frontal panel will be switched on, in case of STEREO MPX Internal is enabled the led STEREO will be switched on, in case of STEREO MPX External is enabled the led MPX will be switched on. 36 /87 5.3.6.2 PRESETTINGS IN MONO MODE [0] Mode Selection [1] Total Deviation Adjustment [2] AES-EBU Enable [3] AES-EBU Ratio Fig. 5.27 â Presetting MONO mode menu In MONO mode the options available are the fine adjustment of output signal deviation and the AES-EBU controls. To navigate in these menus press UP or DOWN keys. 5.3.6.3 PRESETTINGS IN STEREO MPX INTERNAL MODE [0] Mode Selection [1] Total Deviation Adjustment [2] RDS Deviation Adjustment [3] SCA Deviation Adjustment [4] AUX Deviation Adjustment [5] 19KHz/MPX Selection [6] Pilot Tone Deviation 37 /87 [7] Pilot Tone Phase Shift [8] AES-EBU Enable [9] AES-EBU Ratio Fig. 5.28 â Presetting STEREO MPX Int mode menu In STEREO mode MPX Internal enabled, the options available are the fine adjustment of output signal and auxiliary channels deviation, 19KHz/MPX output selection, Pilot Tone regulation and AES-EBU controls. To navigate in these menus press UP or DOWN keys. 5.3.6.4 PRESETTINGS IN STEREO MPX EXTERNAL MODE [0] Mode Selection [1] Total Deviation Adjustment [2] RDS Deviation Adjustment [3] SCA Deviation Adjustment [4] AUX Deviation Adjustment Table 5.7 - Presetting STEREO MPX Ext mode menu 38 /87 5.3.6.5 TOTAL DEVIATION ADJUSTMENT In this menu it is possible to adjust an internal circuit offset (in dB) to set the total output signal deviation to 75KHz (in MONO mode) or 71KHz (in STEREO MODE) regardless the sensitivity level set in the Sensitivity menu. Fig. 5.29 â Presetting total deviation adjustment To change the offset value, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to increase or decrease the value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: -10 dB MAX value: +10 dB STEP: Âą0.05 dB Table 5.8 â Total deviation adjustment permitted values 5.3.6.6 RDS, SCA, AUX DEVIATION ADJUSTMENT In this menu it is possible to adjust an internal circuit offset (in dB) to set the particular auxiliary channel deviation to 4KHz regardless the sensitivity level set in the Sensitivity menu. This option is available only in STEREO mode. Fig. 5.30 â Presetting auxiliary channels deviation adjustment Press UP or DOWN key to select the channel desired. To change the offset value, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to increase or decrease the value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: -5 dB MAX value: +5 dB STEP: Âą0.5 dB Table 5.9 â Auxiliary channels deviation adjustment permitted value 39 /87 5.3.6.7 19KHZ/MPX OUTPUT SELECTION In this menu it is possible to select the output signal at the 19KHz/MPX OUT rear connector: the 19KHz signal or the MPX Internal signal. This option is available only in STEREO MPX Internal mode. Fig. 5.31 â Presetting 19KHz/MPX Out menu To change the output, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select the desired output. Press OK key to confirm or ESC key to exit routine without saving. 5.3.6.8 PILOT TONE DEVIATION In this menu it is possible adjust the deviation of pilot tone, the standard value is 7 KHz (10% of stereo signal deviation of 71 KHz). The deviation change is obtained through an incrementdecrement of the pilot tone level. This option is available only in STEREO MPX Internal mode. Fig. 5.32 â Pilot tone deviation adjustment To change the deviation value, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to increase or decrease the deviation value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: 2 KHz MAX value: 15KHz STEP: Âą0.05 KHz Table 5.10 â Pilot tone deviation adjustment permitted values 40 /87 5.3.6.9 PILOT TONE PHASE SHIFT In this menu it is possible adjust the phase of 19KHz pilot tone. This option is available only in STEREO MPX Internal mode. Fig. 5.33 â Pilot tone phase adjustment To change the phase value, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to increase or decrease the value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: -100° MAX value: +100° STEP: Âą1° Table 5.11 â Pilot tone phase adjustment permitted values 5.3.6.10 AES-EBU CONTROLS In these menus it is possible enable/disable the AES-EBU interface. The menus are available in MONO and STEREO MPX Internal modes. Fig. 5.34 â AES-EBU interface enable menu To enable/disable the AES-EBU interface, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select ON or OFF. Press OK key to confirm or ESC key to exit routine without saving. If the interface is enabled, the internal switch will commutate from analogic Left/Right channels to digital Left/Right ones but the active channels set in the Operat.Mode menu will not change. In case of interface enabled the AES-EBU led in the frontal panel will be switched on. 41 /87 It is possible to change the AES-EBU interface Recovered Master Clock Frequency in the Ratio menu. Fig. 5.35 â AES-EBU Ratio menu To change the AES-EBU Ratio, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. Values available: 128, 256 Table 5.12 â AES-EBU Ratio permitted values 42 /87 5.3.7 ALARMS MENU In these menus it is possible to set the thresholds of intervention of alarms/warnings. In case an event is verified an info will be saved in the history log and the warning or alarm led (depending on event type) will be switched on. To navigate in these menus press UP or DOWN keys. [0] Foldback Reflected [1] Warning Reflected [2] Warning Power Low [3] Alarm Power Low [4] Audio Low Level [5] Audio Low T1 [6] Audio Low T2 [7] Audio Over Level [8] Audio Over T1 [9] Audio Over T2 [10] Audio Event Type Fig. 5.36 â Alarms/Warnings menu flow graph 43 /87 5.3.7.1 WARNING FOLDBACK REFLECTED POWER The unit is provided with a reflected power level proportional protection: in case the output reflected power exceeds the foldback threshold value the unit enters in warning mode and the output forward power is proportionally lowered to maintain the reflected power under the foldback threshold level. The folbadck threshold is indicated as percentage of nominal unit power. Standard factory calibration is 15% of nominal power. Fig. 5.37 â Foldback Reflected menu To change the foldback threshold level, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: 0% MAX value: 100% STEP: Âą1% Table 5.13 â Foldback Reflected permitted values 5.3.7.2 WARNING REFLECTED POWER In this menu it is possible to set a threshold value for a reflected power warning in similar way to the previous menu. The presence of this warning does not alter in any way the output forward power unlike by the foldback reflected warning. The Warning Reflected threshold is indicated as percentage of nominal unit power. Fig. 5.38 â Warning Reflected menu 44 /87 To change the Warning Reflected threshold level, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: 0% MAX value: 100% STEP: Âą1% Table 5.14 â Warning Reflected permitted values To disable this warning set the Warning Reflected to 0%. 5.3.7.3 WARNING POWER LOW In this menu it is possible to set a warning in case the forward power level drops below a threshold. In case the forward power never exceeds the Warning Power Low threshold from the unit switch ON the warning is generated after 40 seconds otherwise after 4 seconds. The Warning Power Low threshold is indicated as percentage of nominal unit power. Fig. 5.39 â Warning power Low menu To change the Warning Power Low threshold, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: 0% MAX value: 100% STEP: Âą1% Table 5.15 â Warning power Low permitted values To disable this warning set the Warning Power Low to 0%. 45 /87 5.3.7.4 ALARM POWER LOW In this menu it is possible to set an alarm in case the forward power level drops below a threshold in a similar mode as previous menu. In case the forward power never exceeds the Alarm Power Low threshold from the unit switch ON the warning is generated after 40 seconds otherwise after 4 seconds. The Alarm Power Low threshold is indicated as percentage of nominal unit power. Fig. 5.40 â Alarm power Low menu To change the Alarm Power Low threshold, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: 0% MAX value: 100% STEP: Âą1% Table 5.16 â Alarm power Low permitted values To disable this alarm set the Alarm Power Low to 0%. 5.3.7.5 AUDIO LOW EVENT The Audio Low warning/alarm is generated if the audio level at an active input channel drops below a threshold set in the menu Audio Low Level for at least T1 seconds. In presence of Audio Low warning/alarm in case the audio level exceeds the Audio Low threshold for at least T2 seconds the warning/alarm status is automatically ended. This warning/alarm is indicated also by the led NO AUDIO switched on in the frontal panel. The timeouts T1 and T2 are set in the menus Audio Low T1 and Audio Low T2. Fig. 5.41 â Audio Low Level menu 46 /87 To change the Audio Low level, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: -20 dBu MAX value: +20 dBu STEP: Âą0.1 dB Table 5.17 â Audio Low Level permitted values To setup the timeouts Audio Low T1 and T2 navigate to the relative menus with UP or DOWN keys. Fig. 5.42 â Audio Low timeout menus To change the Audio Low timeouts, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: 0 sec MAX value: 1000 sec STEP: Âą1 sec Table 5.18 â Audio Low timeouts permitted values To disable this warning/alarm set both the timeouts Audio Low T1 and T2 to 0 sec. 5.3.7.6 AUDIO OVER EVENT The Audio Over warning/alarm is generated if the audio level at an active input channel exceeds a threshold set in the menu Audio Over Level for at least T1 seconds. In presence of Audio Over warning/alarm in case the audio level drops below the Audio Over threshold for at least T2 seconds the warning/alarm status is automatically ended. This warning/alarm is indicated also by the led NO AUDIO switched on in the frontal panel. The timeouts T1 and T2 are set in the menus Audio Over T1 and Audio Over T2. Fig. 5.43 â Audio Over Level menu 47 /87 To change the Audio Over level, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: -20 dBu MAX value: +20 dBu STEP: Âą0.1 dB Table 5.19 â Audio Over Level permitted values To setup the Audio Over timeouts navigate to the relative menus with UP or DOWN keys. Fig. 5.44 â Audio Over timeout menus To change the Audio Over timeouts, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select desired value. Press OK key to confirm or ESC key to exit routine without saving. MIN value: 0 sec MAX value: 1000 sec STEP: 1 sec Table 5.20 â Audio Over timeouts permitted values To disable this warning/alarm set both the timeouts Audio Over T1 and T2 to 0 sec. 5.3.7.7 ALARMS MENU In this menu it is possible to configure the type of audio event for both Audio Low and Audio Over. In case the audio event is configured as warning the yellow warning led will be switched on in the frontal panel and in the history log the event will be saved as warning. In case the audio event is configured as alarm, the red alarm led will be switched on in the frontal panel and the event will be saved as alarm in the history log. Fig. 5.45 â Audio events type menu 48 /87 To change the Audio Event type, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select type desired. Press OK key to confirm or ESC key to exit routine without saving. TYPE AVAILABLE: Warning, Alarm Table 5.21 â Audio events permitted types 5.3.8 MEMORY MENU The unit can be completely configured in 6 different modes (Memories) and these configurations are stored in the internal unit memory. [0] Active Memory [1] Edit Memory 0 [2] Edit Memory 1 [3] Edit Memory 2 [4] Edit Memory 3 [5] Edit Memory 4 [6] Edit Memory 5 [7] Clear Memory Fig. 5.46 â Memory menu flow graph 49 /87 5.3.8.1 ACTIVE MEMORY The active Memory is the current configuration applied to the unit. Any parameter changed during normal unit working mode is automatically applied and saved in the current active Memory. The active Memory is indicated in the sub-menu Active. Fig. 5.47 â Active Memory menu To change the active Memory, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select Memory desired. Press OK key to confirm or ESC key to exit routine without saving. MEMORY AVAILABLE: M0, M1, M2, M3, M4, M5 Table 5.22 â Memory available When a Memory is recalled the unit is reconfigured with the parameters saved in that particular Memory. 5.3.8.2 EDITING A MEMORY In these menus it is possible enable the editing of a Memory parameters, the editing is not available for the Active Memory because for this particular Memory the parameters change is executed and saved in real time. Fig. 5.48 â Edit Memory menus A Memory already manually edited has Full state otherwise is Empty. It has no sense to recall an empty Memory but, if it is recalled, the empty Memory will be an exact copy of the last Active Memory. 50 /87 To enable the editing of a Memory navigate with UP or DOWN keys in the sub-menus up to the desired Memory M, keep pressing OK key until the display shows the line Fig. 5.49 â Enable Memory editing page Press RIGHT key to enable the editing or LEFT key to exit, if the editing is confirmed the display shows the following line Fig. 5.50 â Ending Editing Memory page If editing Memory is enabled, in the first row of every menu between the brackets the edited Memory number will be alternated with the menu ID. Changing parameters in this modality does not influence the unit on air working mode but the parameters are saved in the Memory edited. Pressing ESC key will exit from editing Memory state without any change in that Memory. To save the new parameters it is necessary return in the Memory menu Fig. 5.51 - Memory menu during editing And keep pressing the OK key until the display shows the line Fig. 5.52 â Confirmation editing Memory page Press RIGHT key to confirm the saving procedure or LEFT key to discard the editing. 51 /87 5.3.8.3 CLEAR ALL MEMORY It is possible clear all Memory configurations with the exception of the Active Memory one. To clear all Memory navigate to the menu Clear all Memory with DOWN key. Fig. 5.53 â Clear all Memory menu Keep pressing the OK key until the display shows the line Fig. 5.54 â Clear all Memory confirmation page Press RIGHT key to confirm the cleaning operation, press LEFT key to exit without cleaning. 52 /87 5.3.9 HISTORY MENU In the History menu is present the list of events occurred during the unit operation. The events recorded can be grouped in three types: alarm, warning and info. The alarm is an event type that can compromise the normal unit operation, the warning doesnât compromise the unit operation but have to be examined to prevent alarms. The info is an information about a unit change of state (for example passing in local mode, or exit from warning or alarm state). The menu shows always the last event happened Fig. 5.55 â History menu In the second row on the left the numbers 000 identify the last event (there is the possibility to check the last 200 events), after the symbol â>â a brief event description is provided. To see a total event information and the complete event list press OK key: Fig. 5.56 â History menu event detail page The first row shows the same message as the second row of previous menu, while in the second row the information showed are in order: date, hour and code of event recorded. Press UP or DOWN keys to navigate the event list press OK or ESC key to exit. 53 /87 Here below the complete list of events recognized is indicated: EVENT Max Current Max Environment Temp Foldback Reflected Reset Max Heatsink Temp Max Supply Temp Interlock Open Power On Max Hardware Reflected Fan Warning Frequency Change Change to Local Change to Remote Audio Low Power Low Switch ON Switch OFF Fault too many Alarms End PLL Unlock PLL Unlock Audio Over End Foldback Reflected End Hardware Reflected End Power Low End Audio Low End Audio Over End Fan Warning End Max Heatsink Temp Fault Hardware Reflected Power Low RDS Alarm End RDS Alarm Alarms Present Alarms Absent Warnings Present Warnings Absent RF Present RF Absent Audio Low End Audio Low End Power Low Audio Over End Audio Over NTP Synchronization End NTP Synchronization Warning Reflected End Warning Reflected TYPE ALARM ALARM [Not used] WARNING INFO ALARM ALARM [Not used] WARNING INFO ALARM WARNING INFO INFO INFO ALARM ALARM INFO INFO ALARM INFO ALARM ALARM INFO INFO INFO INFO INFO INFO INFO ALARM WARNING ALARM INFO ALARM INFO INFO INFO INFO INFO [Not used] [Not used] WARNING INFO INFO WARNING INFO WARNING INFO WARNING INFO CODE 0001 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0029 0030 0031 0032 0033 0034 0035 0036 0037 0038 0039 0040 0041 0042 0043 0044 0045 0046 0047 0048 0049 0050 0051 [Not used] If Temperature > 68°C [Not used] Alarm version Alarm version Alarm version For Alarm version For Alarm version For Alarm version Too many hardware reflected events Warning version At least 1 alarm present No alarm present At least 1 warning present No warning present If Pout > 10% of power set value If Pout < 10% of power set value [Not used] [Not used] Warning version For Warning version For Warning version Warning version For Warning version Table 5.23 â Events list 54 /87 Every Warning and Alarm event has the corresponding END info event to indicate the time instant of ending from that particular warning/alarm condition. 5.3.10 GENERALS MENU The Generals menu contains options as time and date set, the RS-485 address, the IP address and netmask. [0] Set Hour [1] Set Minute [2] Set Second [3] Set Day [4] Set Month [5] Set Year [6] Set RS-485 address [7] IP address [8] Netmask Fig. 5.57 â Generals menu flow graph 55 /87 5.3.10.1 TIME SET In these menus it is possible to set the time of day: this time is used in the history log menu during the events saving. To adjust the hour localize the menu Fig. 5.58 â Set hour page To change the hour, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select right value. Press OK key to confirm or ESC key to exit routine without saving. To adjust the minutes press UP or DOWN key Fig. 5.59 â Set minute page To change the minutes, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select right value. Press OK key to confirm or ESC key to exit routine without saving. To adjust the seconds press UP or DOWN key Fig. 5.60 â Set second page To change the seconds, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select right value. Press OK key to confirm or ESC key to exit routine without saving. 56 /87 5.3.10.2 DATE SET In these menus it is possible to set the date: the date is used in the history log menu during the events saving as the time of the day. To adjust the day press UP or DOWN key Fig. 5.61 â Set day page To change the current day, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select right value. Press OK key to confirm or ESC key to exit routine without saving. To adjust the month press UP or DOWN key Fig. 5.62 â Set month page To change the current month, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select right value. Press OK key to confirm or ESC key to exit routine without saving. To adjust the year press UP or DOWN key Fig. 5.63 â Set year page To change the current year, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select right value. Press OK key to confirm or ESC key to exit routine without saving. 57 /87 5.3.10.3 RS-485 ADDRESS MENU In this menu it is possible set the RS-485 address in case the unit is used as slave device in a bus system (for example a high power transmitter or a 1+1 system). Navigate to the menu RS485 Address with UP or DOWN key. Fig. 5.64 â Set RS-485 address page To change the RS-485 address, press the OK key to enter the program mode (blinking arrow in second row on the right). Press UP or DOWN keys to select the desired value. Press OK key to confirm or ESC key to exit routine without saving. 5.3.10.4 NETWORK PARAMETERS These are read only menus, the IP address and Netmask are set directly from webpage if webserver option is available. Fig. 5.65 â Unit IP address page In this menu the actual unit IP address is showed. Fig. 5.66 â Unit netmask page In this menu the actual netmask is showed. 58 /87 6 FRONT PANEL Not all the functions are available from the LCD display: the most important ones are available from the front panel keys and leds present on the unit front panel. 6.1 FRONT PANEL KEYS Reset In case the unit is completely blocked (Fault status) due for example to the repetition of an alarm multiple times, the FAULT led will switch on and to restore the functioning of the unit it is sufficient to press this key (Reset of the alarm/warning/fault status). Local In case the led LOCAL is switched on, the unit is in LOCAL mode and all the functions from the front panel are enabled. If the led is off the unit is in REMOTE mode and it will accept only the commands given by remote. To change the status of the led it is sufficient to press the key. ON/OFF In case the led ON/OFF is switched on, the unit is in ON mode and the RF power is enabled. If the led is off the unit is in OFF mode (standby) and it is only powered but it will not give any output power. To change the status of the led it is sufficient to press the key. 59 /87 UP RIGHT LEFT DOWN OK UP/DOWN/LEFT/RIGHT The keys are available for the menus navigation and the parameter editing if the menu editing is enabled. OK The key is available to enable the editing menu mode and to confirm the parameters change. ESCAPE The key is available to exit from editing menu mode without any change or to return to main menu from any other menu. 60 /87 6.2 FRONT PANEL LEDS The frontal panel leds donât change depending on units model. For the leds name see the Fig.2.1 or Fig.2.3 6.2.1 STATUS LEDS ALARM led This led is switched on in case an alarm event is recognized. It is automatically switched off at the end of the alarm event without the reset needed. It is still possible press reset key to clear the alarm condition. WARNING led This led is switched on in case a warning event is recognized or in case of a parameter is saved or read from unit internal Eeprom memory. It is automatically switched off at the end of the warning event or when the read/write operation on internal Eeprom memory is terminated. ON led This led is switched on at the unit power on. 61 /87 6.2.2 AUDIO LEDS RDS/AUX led This led is switched on if an auxiliary channel (RDS, SCA, AUX) is enabled. MPX led This led is switched on in case the STEREO MPX External mode is enabled. NO AUDIO led This led is switched on in case of Audio Low or Audio Over alarm/warning events. AES EBU led This led is switched on in case the AES-EBU interface is enabled. LIM led This led is switched on in case the limiter is enabled. STEREO led This led is switched on in case the STEREO MPX Internal mode is enabled. PRE EMPH led This led is switched on in case the preemphasis value set is different from Linear. MONO led This led is switched on in case the MONO mode is enabled. 62 /87 6.2.3 CONTROL LEDS PREF led This led is reserved for future uses. PLL LOCK led This led is switched on when the PLL is locked to the frequency set value. AUTO led This led is reserved for future uses. INTLK led This led is switched on in case the rear connector ENABLE is closed. 63 /87 6.2.4 COMMAND LEDS ALARM RESET led This led is switched on in case of unit fault. The unit enters in fault state when 5 alarm hardware reflected events are recognized in 2 minutes. In this case a reset is necessary. LOCAL led This led is switched on in case the unit is in local mode. RF ON led This led is switched on in case the unit is switched on and the RF power is enabled. The output power level is set in the relative menu. 64 /87 7 REMOTE I/O (OPTIONAL) The Remote I/O is an optional interface that provides the DB25 connector REMOTE to monitor and control the unit through digital signals. The signals available are: Pin 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Name TC_1 TC_3 TC_5 TC_7 TC_9 TC_11 VCC_FIELD TS_11_TM4 TS_9_TM2 TS_7/OUT_ANA7 TS_5/OUT_ANA5 TS_3/OUT_ANA3 TS_1/OUT_ANA1 TC_2 TC_4 TC_6 TC_8 TC_10 GND_OUT TS_COM TS_10_TM3 TS_8_TM1/OUT_ANA8 TS_6/OUT_ANA6 TS_4/OUT_ANA4 TS_2/OUT_ANA2 I/O Tele Command Tele Command Tele Command Tele Command Tele Command Tele Command Vcc Tele Signal Tele Signal Tele Signal Tele Signal Tele Signal Tele Signal Tele Command Tele Command Tele Command Tele Command Tele Command GND COMMON Tele Signal Tele Signal Tele Signal Tele Signal Tele Signal Function OFF Change to MEMORY 0 Change to MEMORY 2 Change to MEMORY 4 +12V ON LOCAL AUDIO_OK MEMORY 1 MEMORY 3 MEMORY 5 ON RESET Change to MEMORY 1 Change to MEMORY 3 Change to MEMORY 5 GND Tele Signals Common NO_FAULT RF_OK MEMORY 0 MEMORY 2 MEMORY 4 Table 7.1 â Remote I/O pinout The particular unit state is verified if there is a short-circuit between the relative Tele Signal pin and the Common pin (pin 20). To send a command to the unit (only in remote state) is necessary a short-circuit between the particular Tele Command pin and GND for at least 100ms. 65 /87 8 WEB SERVER (OPTIONAL) As option it is possible to add a remote webserver system via TCP/IP and SNMP. A webserver board is installed on the exciter and, through an Ethernet port, it is possible to read the main parameters of the transmitter and make all main settings. NOTE: The WEB GUI commands work only if the unit is in REMOTE MODE. Connect the unit to a LAN or directly to the computer using a cross cable. Enter the default address from an internet browser. This address is indicated in the GENERALS menu on the front panel of the unit. 66 /87 8.1 WEB PAGES 8.1.1 MAIN PAGE The default page is the MAIN page: Fig. 8.1 â Webserver main page Here all the information regarding the unit and the software are indicated: 1. Unit audio and RF state 2. Login Status: Administrator, Guest 3. Available web pages 4. Unit model and hardware/firmware revision 5. Webserver info and firmware build 67 /87 8.1.2 LOGIN PAGE To have the possibility to change the functioning parameters of the unit you need to enter as administrator. Here the Login page: Fig. 8.2 â Webserver Login page The standard Administration username and password: FACTORY ADMIN ID: admin FACTORY ADMIN PASSWORD: admin FACTORY IP ADDRESS: 192.168.1.251 68 /87 8.1.3 SETTINGS PAGE In this page is present a view of the status of unit parameters, as normally indicated in the front panel on the LCD display. If the login has been done it will be possible to change the values, otherwise it is possible only to see them. Fig. 8.3 â Webserver Setting page The parameters available in this page are: 1. Frequency 2. Power Set 3. Audio options 4. Sensitivity option 5. AES-EBU options 6. Mono/Stereo and Auxiliary channels enable 7. Active Memory status 69 /87 8.1.4 PRESETTINGS PAGE In the Presettings page it is possible to see and change the status of all remains unit parameters. If the login has been done it will be possible to change the values, otherwise it is possible only to see them. Fig. 8.4 â Webserver Presetting page Parameters available are: 1. Mono/Stereo mode 2. Alarms and Warnings Settings 3. Deviation offsets adjustment 70 /87 8.1.5 LOG PAGE The LOG page allows the visualization and the download of the unit history (the register of all the events happened with date, hour and event code). If the login has been done it will be possible to download the file, otherwise it is possible only to see it. Fig. 8.5 â Webserver Log page The Log type can be configured as FULL or RECENT. In FULL mode it is possible see the unit complete list of event saved, in RECENT mode it is available a list of events starting from the selection of RECENT option. The Reset current log button will restart only the RECENT mode of the Log. To restart the Log FULL mode it is necessary to go on Administration page. 71 /87 8.1.6 ADMINISTRATION PAGE If the user is logged as administrator it is possible change all parameters related to the connection of the unit to the network and the SNMP configuration. Fig. 8.6 â Webserver Administration page 72 /87 The parameters available are: 1. Network parameters: IP address, netmask and Gateway address. 2. SNMP configuration. 3. Username and password for both administrator and guest users. 4. NTP configuration 5. Buttons necessary to reconfigure the webserver board. To save a new network or SNMP configuration press SAVE button after the new parameters are set. To apply the new configuration press REBOOT button to restart the webserver board. The RESTART LOG button will restart the FULL mode of webserver Log. 73 /87 8.1.7 MODULATOR UPGRADE PAGE If the login has been done it is possible to upgrade the firmware of the unit uploading the file from this page. The upgrade will be automatically done once the file has been uploaded. The upload is done in 2 steps: ⢠The software is uploaded into the web server board (web module) and stored in it ⢠The software is passed from the web module to the microprocessor of the unit Fig. 8.7 â Webserver Modulator Upgrade page To upgrade the modulator refer to the upgrading procedure. 74 /87 8.1.8 WEBSERVER UPGRADE PAGE If the login has been done it will be possible to upgrade the firmware of the webserver board uploading the file from this page. The upgrade will be automatically done once the file has been uploaded. The upgrade will be automatically done once the file has been uploaded. The upload is done in 2 steps: ⢠The software is uploaded into the webserver board (web module) and stored in it ⢠The software is applied to the web server Fig. 8.8 â Webserver Upgrade page To upgrade the webserver board refer to the upgrading procedure. 75 /87 8.2 UPGRADING PROCEDURES 8.2.1 UPGRADING THE MODULATOR FIRMWARE The modulator firmware upgrade is available only with the webserver board installed. The copies of modulator firmwares are always stored in the webserver board so it is possible the downgrade in case of failed upgrading attempts. To start the procedure please follow these points: 1. Power on the unit maintaining pressed the OK key to start the unit in bootloader mode. Fig. 8.9 â Start in bootloader mode 2. Connect a PC to the unit using a crossover LAN cable. Open a browser and type the IP address of the unit. Usually the boot time of webserver loading is 1 minute, after that the webpage will be active. 3. Login as administrator. 4. Go to the âModulator Upgradeâ menu and press the âSfogliaâ button to select the new firmware. Fig. 8.10 â Modulator Upgrade page 76 /87 5. Select the latest firmware .hex file and click âOPENâ (The file below is just an example, please use the firmware provided by DB Elettronica). Fig. 8.11 â New firmware selection 6. Click on âUploadâ button and confirm the operation pressing âOKâ button on the popup window. Fig. 8.12 â Upload the new firmware Fig. 8.13 â Confirm the upload 77 /87 7. The new firmware will be added on the list. Select it from the list and click on âUpgradeâ button. Fig. 8.14 â Upgrade to the new firmware 8. The procedure starts erasing the flash, on the display of the transmitter the text âERASE FLASHâ will show on. Fig. 8.15 â Erase the flash before the upgrade 9. During the firmware upgrade on the display of the transmitter the text âupgrading âŚâ will show on. Fig. 8.16 â Upgrade in working 10. The Control Board will be upgraded with the new firmware. The operation process will take about 5 minutes. When the process is finished the text âENDâ will be shown at the end of the log report. 78 /87 Fig. 8.17 â Upgrade complete When the upgrade is complete, the transmitter will be restarted automatically. In case of procedure failed, power off the unit, wait some seconds and power on the unit. Now retry the upgrade procedure again. In case of new upgrading failed contact the assistance. 79 /87 8.2.2 UPGRADING THE WEBSERVER BOARD FIRMWARE To upgrade the webserver board please follow the next steps: 1. Connect a PC to the Mozart transmitter using a crossover LAN cable. Open a browser and type the IP Address of transmitter. 2. Login as administrator. 3. Go to the âWebserver Upgradeâ menu and click on âSfogliaâ button. Fig. 8.18 â Webserver Upgrade page 4. Select the latest firmware .tgz file and click âOPENâ. (The file below is just an example, please use the firmware provided by DB Elettronica). Fig. 8.19 â Select the new webserver board firmware 80 /87 5. Click on âUploadâ button and confirm the operation pressing âOKâ button. Fig. 8.20 â Upload the firmware to webserver Fig. 8.21 â Confirm the uploading 6. The following screen will be shown on while the process is running. Fig. 8.22 â Busy state during upload procedure 81 /87 7. The new firmware will be added on the list. Select it and click on âUpgradeâ button. Fig. 8.23 â New firmware ready to upgrade 8. Select âOKâ to confirm the operation and âOKâ after the message was read. Fig. 8.24 â Confirmations to upgrade 9. Wait until the following screen will disappear Fig. 8.25 â Upgrade in working 82 /87 10. The webserver is ready to be upgraded. Go to âAdministrationâ menu and click on the âREBOOTâ button. Confirm the operation pressing âOKâ button. The webserver will be restarted with the new firmware. Fig. 8.26 â Reboot the webserver Fig. 8.27 â Confirm the reboot 11. Wait until the process is finished. The operation process will take about 90 seconds. Fig. 8.28 â Wait until the reboot is completed 83 /87 8.3 SNMP PROTOCOL SNMP (Simple Network Management Protocol) is used for monitoring and controlling a wide variety of different units in a network. A description of the unit - the MIB (Management Information Base) - must be loaded in the central unit ("manager") from which the unit is monitored. A monitored unit contains a program ("agent") which can answer queries from the manager and execute commands. Furthermore, the agent may of its own accord generate a message (âtrapâ or âinformâ) and send it to the manager. In this way, the central unit can be informed of a fault. 8.3.1 MANAGEMENT INFORMATION BASE MIB The MIBs required for monitoring and controlling the unit can be requested to assistance. The packet IRT-TC-MIB.04.05.2007 contains a group of files: Fig. 8.29 â List of file of MIB packet Select and open the FM folder and load the file IRT-FM-SINGLETRANSMITTER-MIB in the MIB browser of manager unit. 84 /87 The supported protocol is SNMPv2c. Fig. 8.30 â FM Single Transmitter MIB 85 /87 8.3.2 MESSAGE TRAP AND INFORM The events that can generate a trap or inform (depending on user configuration) are grouped in the fmEventsST folder: EVENT OID DESCRIPTION fmSTTransmitterOpModeEvent .1.3.6.1.4.1.19831.1.1.3.1.0.1 Unit in ON state fmSTRFPresentEvent .1.3.6.1.4.1.19831.1.1.3.1.0.2 RF present event recognized fmSTFaultEvent .1.3.6.1.4.1.19831.1.1.3.1.0.3 Presence of alarms fwSTWarningEvent .1.3.6.1.4.1.19831.1.1.3.1.0.4 Presence of Warnings fmSTLocalModeEvent .1.3.6.1.4.1.19831.1.1.3.1.0.5 Unit in Local mode Table 8.1 â Traps and Informs available The Traps/Informs can be configured in the webpage on Administration menu. Fig. 8.31 - Traps and Informs configuration The trap/inform messages can be sent to 2 different IP address set in TRAP IP ADDRESS box with the relative port. 86 /87 In the TRAP TYPE box select the message type desired, trap or inform. If inform is selected, the timeout the agent waits (if no answer from the manager) before re-send the inform message can be set in the INFORMS TIMEOUT box, the number of inform retransmission can be set in INFORMS RETRIES box. The messages trap/inform have to be enable and can be enable singly. The enable is provided to the OIDs (fmSTEventEnable folder): EVENT OID DESCRIPTION fmSTTransmitterOpModeEventEnable .1.3.6.1.4.1.19831.1.1.3.1.2.1.1 1=Enable, 2=Disable fmSTRFPresentEventEnable .1.3.6.1.4.1.19831.1.1.3.1.2.1.2 1=Enable, 2=Disable fmSTFaultEventEnable .1.3.6.1.4.1.19831.1.1.3.1.2.1.3 1=Enable, 2=Disable fwSTWarningEventEnable .1.3.6.1.4.1.19831.1.1.3.1.2.1.4 1=Enable, 2=Disable fmSTLocalModeEventEnable .1.3.6.1.4.1.19831.1.1.3.1.2.1.5 1=Enable, 2=Disable 8.3.3 COMMANDS AND STATE Commands and State available through SNMP are summed in the following table: EVENT OID TYPE DESCIPTION fmSTTransmitterOpMode .1.3.6.1.4.1.19831.1.1.3.1.1.1 Read and Write 1=ON, 2=OFF fmSTRFPresent .1.3.6.1.4.1.19831.1.1.3.1.1.2 Read only 1=Present, 2=Not Present fmSTFault .1.3.6.1.4.1.19831.1.1.3.1.1.3 Read only 1=Fault, 2=No Fault fwSTWarning .1.3.6.1.4.1.19831.1.1.3.1.1.4 Read only 1=Warning, 2=No Warning fmSTLocalMode .1.3.6.1.4.1.19831.1.1.3.1.1.5 Read only 1=Local, 2=Remote The commands are accepted by the unit only in remote mode and if the community strings are correctly set for both read and write operations. The community read/write strings have to be set both to the agent and manager units. In the webpage can be set in the Administration menu. 87 /87
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : IlariaCavinato Create Date : 2014:04:03 14:10:14+02:00 Modify Date : 2014:07:01 17:12:47-04:00 Subject : Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : IlariaCavinato Description : Title : Mozart series - User Manual R1.0.3 Creator Tool : PDFCreator Version 1.2.3 Metadata Date : 2014:07:01 17:12:47-04:00 Keywords : Producer : GPL Ghostscript 9.04 Document ID : uuid:541eae31-5436-47c9-b9b0-366a9917c5b8 Instance ID : uuid:617612e8-1db8-4119-b8a0-a0ba7bec493e Page Count : 87EXIF Metadata provided by EXIF.tools