DGL Group CCSELBT Coca-Cola Wireless Selfie Stick User Manual
DGL Group LTD. Coca-Cola Wireless Selfie Stick
User Manual
DGL Group LTD.
Coca-Cola Wireless Selfie Stick
Mode No.: CC-SLF-BT-ASST
Thanks for your support of this wireless mobile phone monopod from Kjstar Co.,Ltd
China.This monopod is based on the Bluetooth HID wireless communication
technology.please confirm that your samart phone supports this technology.This
monopod can intelligently recognizies and works with smart phones with IOS 4.0 or
Android 3.0 and above Also it can be manually switched if necessary.
1. Function
Autodyne and vide wirelessly by Mobile
2. Description of the whole package: 1 piece phone clamp , 1 piece Gasket ,1 piece USB
charging
cable, 1 piece user manual, 1piece Warranty card
3. Specification
3.1 Working enviroment temperature:- 10-+40°C
3.2 working enviroment relative
Humidity:10%-90%
.1.
3.3 Battery Capacity: 55Mah
3.4 charging Voltage: DC 5.0V
3.5 Autodyne Frequence: 500times
3.6 Standby Time: 100 hours
3.7 Charging time: 1hour
3.8 Memory quantity: 4times
3.9 The product automatically goes to “sleep”within 2 hours unused, it will “wake up”5
seconds later after pressing the key of “press”
4. Usage intructions
4.1 Full charging time: 1 hourle
4.2 Paring: Mobile phone and Monopod
Apple IOS System: Open the “setting”→Bluetooth→turn on monopod→Searching
autodyne→ system “Kjstar” →enter system→complete Paring
Android System: open the “setting” →Bluetooth→Scanning→turn on the
monopod→Searching autodyne system “Kjstar” →enter the system→complete paring
.2.
★ The paringof the camera and monopod need not password,The paring is on-going
when the blue LED light is flashing quickly,please operate it within 40
seconds,otherwise you need to restar the power,rescan and repair.
4.3 Autodyne
Put the mobile phone to the monopod→enter the camera application “ ”
→stretch the monopod→press the key of “press”
★ some devicees with the android system might not normally work with the monopod
in that case,please download an APP “Kjstar-365”from our website or you can aslo
try switch the system of the monopod
5. Switch of the system:
Push the “press”button and turn one the power of the monopod in the same time and
then pair it with your device.
.3.
6. Caution and safety
6.1 Press read the instruction carefully before uasage
6.2 Please turn off the nearby bluetooth to 6 avoid the signal interference
6.3it may conflict when using some mobile phone keyboard with it simultaneously,
please close the bluetooth or turn off the power of the monopodl
6.4 Safety
6.4.1 please do not dismantle the products
6.4.2 please do not use corrosive solvent to clean it
6.4.3 Forbidden to use it or charging under high temperature or strong light
6.4.4 Forbidden to use it in the rain with damp or soaked
6.4.5 Forbidden to throw it into the fire, so as to avoid the explosion
6.4.6 Please do not knock it heaviy
.4.
7. Other cautions:
7.1 No power or poower turned off:
LED turned off
7.2 Bluetooth pairing: Bluetooth LED
Light keep flashing at middle frequency
7.3 Taking photo:Blue LED light flash one time
7.4 Blue paring Sucessfuly or wake up
Sleep: LED light keep flashing quickly
7.5 Low voltage: LED light keep flashing slowly
7.6 Charging : Red LED light on,full charging red LED Light off
.5.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.