DGL Group QDRTBCAM Remote Control User Manual AW QDR TB9 Manual
DGL Group LTD. Remote Control AW QDR TB9 Manual
15_AW-QDR-TBCAM UserMan
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3191042 |
| Application ID | zjRBHVsPHo2PLpXeV9PjpA== |
| Document Description | 15_AW-QDR-TBCAM UserMan |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 83.16kB (1039542 bits) |
| Date Submitted | 2016-11-09 00:00:00 |
| Date Available | 2016-11-09 00:00:00 |
| Creation Date | 2016-09-08 16:09:53 |
| Producing Software | Adobe PDF library 11.00 |
| Document Lastmod | 2016-09-08 16:09:53 |
| Document Title | AW-QDR-TB9-Manual |
| Document Creator | Adobe Illustrator CC 2014 (Macintosh) |
quadrone AW-QDR-TBCAM FCC ID:2AANZQDRTBCAM Instruction Manual Introduction Warnings • Thank you for choosing Quadrone! This is a four-axis aircraft that can fly outdoors, in order to make it easier to control the aircraft. Please carefully read this manual before operating your Quadrone. Please keep this manual for future reference. • Before your first flight, please take the time to carefully read this manual containing important flight information which will help your first flight go more smoothly. Table of Contents Introduction Table of Contents Notice Warning Additional Warnings and Precautions Safety Notes Included Remote Controller Diagram Remote Controller Battery Installation Charging Your Drone Installing the Camera Syncing the Quad and Remote Flight Controls Practice Tips Trimming the Quad Flips and Rolls Speed Selection Headless Mode Auto Return Taking Photo/Video Changing the Blades Troubleshooting 10 10 10 12 Notice • All instructions, warranties and other collateral documents are subject to change at the sole discretion of our company. • Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property or cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense, and requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or property. This product is not intended for use by children without direct adult supervision. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in this manual, prior to assembly, set up or use, in order to operate correctly and avoid damage or serious injury. Additional Warnings and Precautions 1. Age Recommendation: Not for children under 14 years of age. This is not a toy. 2. Always operate in open spaces away from obstacles, people, and hazards. 3. Always follow directions and warnings for this and any optional equipment carefully. (chargers, rechargeable battery packs, etc) 4. Always keep small parts and electrical parts out of the reach of children. 5. Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture can cause damage to electronics. 6. Never place any portion of the model in your mouth as it could cause serious injury or even death. 7. Never operate your model with low batteries. • RC models are composed of many precise electrical components. It is important to keep the model and associated equipment away from moisture and other contaminants. The introduction of exposure to water or moisture in any form can cause the model to malfunction or crash. Do not operate or expose to rain or moisture. • To avoid a potential fire hazard from batteries, do not short, reverse polarity, or puncture batteries. Battery charging should be done under adult supervision at all times, at a location out of reach of children. Do not mix Ni-Cad and Alkaline batteries. • Make sure the batteries are installed correctly to ensure correct polarity. If you do not plan to use your Quadrone for an extended period of time, remove the batteries from the controller to avoid battery leakage which may damage the controller. Please dispose depleted batteries according to local laws and ordinances. • Li-Polymer batteries have higher operational risks compared to other batteries. It is imperative to follow proper operational guidelines. The manufacturer and dealer assume no liability for accidental damages caused by improper usage. Do not use any other charger other than the supplied charger included in this packaging in order to avoid potential fire or explosion. Do not crush, disassemble, burn, or reverse polarity. • RC models are made from various forms of plastic very susceptible to damage or deformation due to extreme heat and cold temperatures. Make sure not to store the model near any heat source or adverse temperatures. Remote Controller Diagram Charging Your Drone Antenna Power lndicator Flip Button Speed Selection Throttle Joystick Directional Joystick Headless Mode (Press) Photo Button (Up) Video Button (Down) Forward/Backward Trim Button Light Control (Left) Auto Return (Right) Alerion Trim Button Power Switch • To charge your Quadrone, first disconnect the battery from the drone and slide it out of its holder. Plug the provided USB charger into a USB port. A green light on the USB charger will turn on. Now connect the USB charger to the battery. The light on the charger will turn red, indicating the battery is now charging. The red light will turn green again once the charging process has completed. Always charge your Quadrone under adult supervision and out of the reach of children. Charging time is approximately 30 minutes. When you are ready to fly your Quadrone again, reinsert the battery into its slot on the bottom of the drone. Remote Controller Battery Installation To install batteries, use the included screw driver to open the battery cover. Rotate counter clockwise to loosen screw. Insert 4 AA batteries into the remote. Make sure the batteries are installed in the correct polarity as indicated in the controller. Do not mix old and new batteries or batteries with different chemistries. Reattach battery cover. Rotate screw clockwise to refasten. • This product is suitable for indoor and outdoor use. Please make sure you choose a flight area with no obstacles and maintain a safe distance from people and pets. Do not operate near power lines. 2. Lower the Throttle Joystick on the remote to its lowest position. Turn the remote on. Push the Throttle Joystick to its highest position. The lights on the Quadrone will stop flashing and stay on and the remote will beep. You are now ready to fly your drone. USB Charger x1 Extra Blades x4 Forward/Backward 2. Connect the camera by inserting the power cable into the slot on the bottom of the drone. Trimming the Quad • If your Quadrone is leaning to or favoring a side, you may need to use the trim feature to balance it out so it flies straight. Battery cover Installing the Landing Gear and Crash Guards If the Quadrone leans forward, press the Down Forward/Backward Trim button until it balances out. If the Quadrone leans forward, press the Up Forward/Backward Trim button until it balances out. Aileron Push the directional joystick to the right. The Quadrone will fly to the right. • If you are not going to use your Quadrone for an extended period of time, please take out the batteries in your remote controller. Potential battery leakage could occur and possibly damage the remote or create a fire hazard. • Before flying your Quadrone, it is highly recommended that you familiarize yourself completely with its controls. Read through the instruction manual completely before attempting your first flight. Elevation Push up on the throttle joystick. The Quadrone will begin to ascend. Camera x1 Pull down on the throttle joystick. The Quadrone will begin to descend. 2. To install the crash guards, insert them into the slots at the end of each arm. Use the provide srew and screwdriver to secure the guard in place. Li-Polymer Battery x1 Aileron If the Quadrone leans to the right, press the Left Aileron Trim button until it straightens out. Push the directional joystick to the left. The Quadrone will fly to left. If the Quadrone leans to the right, press the Left Aileron Trim button until it straightens out. Practice Tips • Use these recommended practice exercises to become a better Quadrone pilot: Elevation: Raise the Quadrone using the throttle joystick. Gradually lower the Quadrone so it lands softly to the ground. Direction: Move the Quadrone in a cross pattern using the directional joystick. Move forward, backward, left, right, and back to its original position. Turning: Flips and Rolls • Your Quadrone can perform impressive flips and rolls in midair. In order to do this, press the flip button on your remote during flight. Move the directional joystick in any direction and the aircraft will perform a coinciding flip. See diagram below: Auto Return Troubleshooting Once you have mounted the new blade, you can refasten it with the screw. Rotate clockwise to tighten. • To enter Auto Return simply press the Auto Return button while in Headless Mode. The remote will beep and the lights on the quad will begin to flash. The drone will being to fly directly backwards towards the remote.To exit Auto Return, press the button again or press forward on the Directional Joystick. Forward/Backward Push the directional joystick to the left. The Quadrone will turn to left. 1. To install the landing gear, simply insert the landing gear into the bottom of the drone. The landing gear will snap in when fully inserted. Screwdriver x1 Push the throttle joystick to the left. The Quadrone will turn to left. Push the directional joystick to forward. The Quadrone will fly forward. 1. Slide the camera into the slots under the drone on the battery holder to secure it to the drone. 4 Alkaline batteries Remote Controller x1 Push the throttle joystick to the right. The Quadrone will turn to right. 1. Insert the battery into the drone and connect its wires. Turn on the drone and place it on a flat surface. The lights on the drone will begin to flash. Do not move the Quadrone during the syncing process to ensure the gyroscope stays balanced. Once you have mastered the previous three exercises, draw a circle on the ground. Practice flying within the confines of the circle. Narrow the circle as your skills progress. Flight Controls Included Quadrone Tumbler-9 x1 Flying: Turning Installing the Camera Safety Notes • If this is your first time flying a quadcopter read the manual carefully. Seek the help of an experienced pilot to help you fly. These safety instructions are intended not only for the protection of your Quadrone but also to protect your own safety. Improper operation can cause injury or property damage. Syncing the Quad and Remote Turn the Quadrone in a throttle joystick. Turn left and right repeatedly, and back to its original position. * If the trim buttons do not correct the problem, you will have to recalibrate your drone. To do so, place the Quadrone on a flat surface. Hold the two joysticks down and to the right as depicted in the figure. The lights on the will begin to flash. Once the lights on the quad stop blinking for two seconds, recalibration is complete. Speed Selection • Your Quadrone can fly at four speeds. To select a speed, press the Speed Selection button on your remote. Your remote will beep each time you switch speeds. Slow Speed: 1 Beep Medium Speed: 2 Beeps Fast Speed: 3 Beeps Full Speed: 4 Beeps Headless Mode • When in Headless Mode, no matter what direction the quadcopter faces, it will respond according to the direction pushed on the remote. (Forward on the remote will make the quadcopter fly forward, even if it is pointing in another direction.) To enter Headless Mode, land the Quadrone on a flat surface. Press the down on the Directional Joystick. The remote will beep and the lights on the quad will begin to flash. To exit Headless Mode, simply press the joystick again. The remote will beep again and all lights will remain on and return to normal. Taking Photo/Video Problem Cause Drone’s LED lights blink continuously for more than 4 seconds after quad is turned on. No response to controller. Unable to sync to remote controller. Repeat power sequence and re-sync. (See pg. 5) No response after quad is turned on. 1. Remote batteries have been depleted. 2. Batteries are installed at incorrect polarity. 1. Replace batteries. 2. Reinstall batteries at correct polarity. Motor does not respond to throttle. Battery has been depleted. Recharge quad battery. Motor spins but doesn’t take off. 1. Bent rotor blades. 2. Quad battery is depleted. 1. Replace damaged blade. 2. Recharge battery. Quad is making a loud vibration noise. Bent or damaged rotor blades. Replace damaged blade. Quad still wanders forward after trim adjustment. Forward trim is too high. 1. Lower forward trim. 2. Recalibrate drone. Cannot fly after crash. 1. Motor fell out. 2. Gear loosened. 1. Reinstall motor. 2. Tighten gear. • To take a photo, press up on the Photo/Video button on the remote. The light on the camera will flash and the remote will beep, indicating a picture has been taken. • To take a video, press down on the Photo/Video button on the remote. The light on the camera will flash continuously and the remote will beep twice, indicating a video is being recorded. Press down on the Photo/Video button again to stop recording. 10 Limited 90-Day Warranty DGL Group, Ltd. warrants to the original consumer that this product is free from any electrical or mechanical defects for a period or 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, DGL Group, Ltd. will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center. The warranty covers normal consumer use and does not cover damage that occurs in shipment of failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty does not cover cost of repairs made or attempted outside by third-party individuals and fitness, are hereby limited to 90 DAYS from the date or purchase. Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded. Some states do not allow limitations on the duration of implied warranties and do not allow exclusion of incidental or consequential damages, so the above limitations and exclusions in these instances may not apply. REPAIR/REPLACE PRODUCT If your product begins to malfunction or stop working, immediately call or email our warranty center at the phone/email listed below. If it is determined that a return is necessary, our warranty department will issue you an RMA number/form and an address to the nearest return center to ship the product to. IMPORTANT NOTICE: We will reject all returns that are not accompanied by an issued RMA form and number so make sure to contact our warranty center before attempting to return your product! PREPARATION FOR SHIPPING YOUR PRODUCT Please repack your product in a durable box, preferably in the original carton, and send it prepaid, and adequately insured. Include the RMA form that was issued by our warranty department along with your daytime telephone number and email address (if available) inside the shipping carton. If your warranty has expired, contact our warranty center for charged service. For further information please send all inquiries to support@dglusa.com WARNING: Changing the Blades • If a blade breaks or falls off your Quadrone during a crash, it will be up to you to repair it. Use the screwdriver included in the package to remove the screw, detaching the propeller from the drone. Rotate counter-clockwise to loosen. Remove the damaged blade from the motor. You can now attach a new blade. It is important for the correct blade to be put on the correct motor or the drone will not fly correctly. A letter is marked on each blade to indicate which motor it should go on. Solution CHOKING HAZARD-Small parts. Not for children under 3 years. DGL Toys™ is an innovative division of DGL Group, Ltd. Other trademarks and trade names are those of their respective owners. DGL Toys, 195 Raritan Center Parkway, Edison, NJ 08837. Specifications, colors and contents may vary from illustrations. Conforms to safety requirements of ASTM, FCC, & CPSIA. BATTERY WARNING: • Do no mix alkaline, standard (carbon zinc), rechargeable (nickel hydride) batteries. • Do not mix old and new batteries. • Non-rechargeable batteries should not be recharged. • Rechargeable batteries should be removed from the appliance before being charged. • Rechargeable batteries should be charged under adult supervision only. • Exhausted batteries should be removed. • The supply terminals should not be short-circuited. • Only batteries of the same or equivalent type are recommended to be used. • Batteries should be inserted with the correct polarity. 11 12 IMPORTANT NOTICE! Tested to comply with FCC standards. FOR HOME OR OFFICE USE. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT AT: DGL Group. Ltd. WARRANTY REPLACEMENT DEPARTMENT TEL: 888-987-3089 support@dglusa.com Safety Guidelines • Follow community-based safety guidelines, as developed by organizations such as the Academy of Model Aeronautics (AMA). • Fly no higher than 400 feet and remain below any surrounding obstacles when possible. • Keep your drone in eyesight at all times, and use an observer to assist if needed. • Remain well clear of and do not interfere with manned aircraft operations, and you must see and avoid other aircraft and obstacles at all times. • Do not intentionally fly over unprotected persons or moving vehicles, and remain at least 25 feet away from individuals and vulnerable property. • Contact the airport or control tower before flying within five miles of an airport. • Do not fly in adverse weather conditions such as in high winds or reduced visibility. • Do not fly under the influence of alcohol or drugs. • Ensure the operating environment is safe and that the operator is competent and proficient in the operation of the drone. • Do not fly near or over sensitive infrastructure or property such as power stations, water treatment facilities, correctional facilities, heavily traveled roadways, government facilities, etc. • Check and follow all local laws and ordinances before flying over private property. • Do not conduct surveillance or photograph persons in areas where there is an expectation of privacy without the individual’s permission. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING! To reduce the risk of fire or burns: Do not disassemble, crush, puncture, or short external connectors contacts. Use only with specified charger and player. Do not dispose of in fire or water. Do not expose to high temperature above 140° F (60 ° C). Store between 32° F (0 ° C) and 140° F (60 ° C). Keep away from children. See operating instructions of this battery or product. Li-ion Battery Must Be Disposed Of Properly Batteries should be recycled or disposed of as per State and Local guidelines. Manufactured in China. Batch Ref: XXXX Model Number: XXXX 13 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c014 79.156821, 2014/08/29-03:07:50 Format : application/pdf Title : AW-QDR-TB9-Manual Metadata Date : 2016:09:08 16:09:53-04:00 Modify Date : 2016:09:08 16:09:53-04:00 Create Date : 2016:09:08 16:09:53-04:00 Creator Tool : Adobe Illustrator CC 2014 (Macintosh) Thumbnail Width : 256 Thumbnail Height : 24 Thumbnail Format : JPEG Thumbnail Image : (Binary data 3991 bytes, use -b option to extract) Instance ID : uuid:d93ddc0f-ed7f-8642-a5cf-26a9257fe0ec Document ID : xmp.did:d70d70de-7787-45cc-a9ee-a720a32249af Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:ac2af48b-edab-486e-aac2-10324378ccb4 Derived From Document ID : xmp.did:ac2af48b-edab-486e-aac2-10324378ccb4 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : default History Action : saved, saved History Instance ID : xmp.iid:CBA355A2FEBFE1118A5984573AC21E8B, xmp.iid:d70d70de-7787-45cc-a9ee-a720a32249af History When : 2012:06:27 11:48:04+08:00, 2016:09:08 16:09:43-04:00 History Software Agent : Adobe Illustrator CS5, Adobe Illustrator CC 2014 (Macintosh) History Changed : /, / Startup Profile : Print Has Visible Overprint : True Has Visible Transparency : False N Pages : 1 Max Page Size W : 2276.331348 Max Page Size H : 226.501324 Max Page Size Unit : Millimeters Font Name : Arial-BoldMT, GoodTimesRg-Regular, Helvetica, Helvetica-Bold, HelveticaNeue-Roman, HelveticaNeue-Black, HelveticaNeueLTPro-Roman, MyriadPro-Regular, Helvetica-Black Font Family : Arial, Good Times, Helvetica, Helvetica, Helvetica Neue, Helvetica Neue, Helvetica Neue LT Pro, Myriad Pro, Helvetica Black Font Face : Bold, Regular, Regular, Bold, 55 Roman, 95 Black, 55 Roman, Regular, Black Font Type : Open Type, TrueType, TrueType, TrueType, Type 1, Type 1, Open Type, Open Type, Unknown Font Version : Version 5.06, Version 4.001, 9.0d3e2, 9.0d3e2, 001.101, 001.001, Version 1.000;PS 001.000;Core 1.0.38, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329 Font Composite : False, False, False, False, False, False, False, False, False Font File Name : Arial Bold.ttf, good times rg.ttf, Helvetica.dfont, Helvetica.dfont, HelveNeuRom; Helvetica Neue.t1, HelveNeuBla; Helvetica Neue.t1, HelveticaNeueLTPro-Roman.otf, MyriadPro-Regular.otf, MyriadPro-Regular.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : Default Swatch Group Swatch Groups Group Type : 0 Swatch Groups Colorants Swatch Name: [Registration] 2 Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Cyan : 100.000000 Swatch Groups Colorants Magenta : 100.000000 Swatch Groups Colorants Yellow : 100.000000 Swatch Groups Colorants Black : 100.000000 Producer : Adobe PDF library 11.00 Page Count : 1 Creator : Adobe Illustrator CC 2014 (Macintosh)EXIF Metadata provided by EXIF.tools