DISH Technologies 301LM LIGHTSWITCH COVER MODULE User Manual Manual

Echostar Technologies LLC LIGHTSWITCH COVER MODULE Manual

Manual

LIGHT SWITCHQUICK START GUIDECopyright © 2014. EchoStar Technologies L.L.C., Englewood, Colorado 80112. All rights reserved. EchoStar is a registered trademark of EchoStar Technologies L.L.C. Other products, brands, and companies mentioned are the Trademarks of their respective owner(s). This product is designed in the United States and manufactured in Mexico. p/n 204886REGULATORY INFORMATIONFEDERAL COMMUNICATIONS COMMISSION NOTIFICATIONThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.If none of the remedies stops the radio interference, you should contact a licensed radio/television technician, your satellite dealer, or call the Customer Service Center at 1-800-333-DISH (3474), for assistance.Product must be installed at least 20 cm (~8 inches) from typical person locations per FCC RF exposure regulations.Do not make changes or modifications to this equipment. This could void the user’s authority to operate the equipment.This Limited Warranty is a legal document. Keep it in a safe place. Remember to retain your Bill of Sale for warranty service! Any items returned without a copy of the Proof of Purchase will be considered out of warranty.This warranty extends only to the original user (“you,” “your”) of the EchoStar device and is limited to the purchase price of the device. EchoStar Technologies L.L.C. and its afliated companies (“EchoStar,” “we,” “our,” “us”) warrant this device against defects in materials or workmanship as follows.For one year from the original date of purchase, if we nd the device is defective subject to the limits of this warranty, we will replace the device at no charge for parts or labor. We warrant any such work done against defects in materials or workmanship for the remaining part of the original warranty period.This warranty does not cover installation of the EchoStar System; consumer instruction; physical set up or adjustment of any consumer electronic equipment; remote control batteries; signal reception problems; loss of use of the equipment; unused programming charges due to equipment malfunction; cosmetic damage; damage due to lightning, electrical or telephone line surges, re, ood, or other acts of Nature; accident; misuse; abuse; repair or alteration by other than our factory service; negligence; commercial or institutional use; improper or neglected maintenance; equipment sold AS IS or WITH ALL FAULTS; equipment removal or reinstallation; shipping damage if the equipment was not packed and shipped in the manner we prescribe; nor equipment purchased, serviced, or operated outside the contiguous United States of America.REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY. WE SHALL NOT BE HELD LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY ON THIS DEVICE, NOR FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE RESULTING FROM THE USE OF, OR INABILITY TO USE, THIS DEVICE. SOME STATES MAY LIMIT OR EXCLUDE THE FOREGOING LIMITATION, SO THE ABOVE EXCLUSION OR LIMITTION MAY NOT APPLY TO YOU. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL OUR LIABILITY, IF ANY, EXCEED THE PURCHASE PRICE PAID FOR THIS DEVICE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS DEVICE IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG A STATUTORY OR IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. WE RESERVE THE RIGHT TO REFUSE TO HONOR THIS WARRANTY IF WE DETERMINE ANY OF THE ABOVE EXCEPTIONS TO HAVE CAUSED THIS DEVICE NOT TO HAVE PERFORMED PROPERLY. THIS WARRANTY SHALL BE VOID IF ANY FACTORY-APPLIED IDENTIFICATION MARK, INCLUDING BUT NOT LIMITED TO SERIAL OR CONDITIONAL ACCESS NUMBERS, HAS BEEN ALTERED OR REMOVED. THIS WARRANTY SHALL ALSO BE VOID IF THE DEVICE HAS BEEN OPENED BY AN UNAUTHORIZED PERSON (with the exception of opening the battery cover).LIMITED WARRANTY
WELCOMEThank you for buying the Light Switch. The Light Switch allows you to control a light switch from the convenience of your receiver and TV. Please follow these instructions to install your new Light Switch.PACKAGE CONTENTS: LightSwitchTwo-sidedMounting AdhesiveQuick Start Guide USING YOUR LIGHT SWITCHSETUP AND INSTALLATION 54If you want to leave the Light Switch on a table, make sure the original light switch is in the on position. Follow the instructions on your home automation receiver to complete setup.If you want to install the Light Switch over your current light switch, continue with these instructions.Line the back plate of the Light Switch up with the screw holes, ensuring the that back plate is properly positioned with the UP printed on the back plate facing up. For a rocker-style light switch, trim the back plate as needed.6Insert the two screws and tighten with a screwdriver.Snap the Light Switch cover on the back plate on the wall using the tabs, ensuring it is secure.92Plug a light switch module (provided separately) into a switched outlet and plug the lamp into it.The Light Switch turns on and/or off any device plugged into a switched outlet. The device must receive power from a separately installed light switch module.1Decide whether you want the Light Switch on the wall where the current switch is located or if you would like it on a table somewhere else in the room. 3Remove the Light Switch cover. Press on the side tabs to remove the back plate from the Light Switch.7Put the Light Switch in the on position.8Pull the plastic tab that is over the battery contacts.LIGHT SWITCHQUICK START GUIDEON

Navigation menu