Dane Technologies 600-044 Periodic Transmitter for Electric Cart Pusher User Manual

Download:
Mirror Download [FCC.gov]
Document ID	604186
Application ID	r44T81WqM+CNzh+DxDKgXw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.34kB (141724 bits)
Date Submitted	2005-11-18 00:00:00
Date Available	2005-11-18 00:00:00
Creation Date	2005-10-27 10:39:32
Producing Software	Neevia docuPrinter Pro v5.1 (http://neevia.com)
Document Lastmod	2005-11-17 17:10:06
Document Title	Microsoft Word - 970-005 QK2000 Owner Manual 10-10-05
Document Creator	Neevia docuPrinter Pro

QUICKART 2000
OWNER’S MANUAL
OPERATING INSTRUCTIONS
TRAINING GUIDE
TABLE OF CONTENTS
SECTION
TOPIC
Owner’s Manual and Operating Instructions .................................. 1
Troubleshooting Flowchart ............................................................ 2
Training Manual .............................................................................. 3
Certified Operator’s Test................................................................. 4
Note on radio equipment used:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Changes not expressly approved by Dane Technologies could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
− Reorient or relocate the receiving antenna.
− Increase the separation between the equipment and receiver.
− Connect the equipment into an outlet on a circuit different from that which the receiver is connected.
− Consult the dealer or an experienced radio/TV technician for help.
The abbreviation IC, before the Canadian Registration Number signifies that registration was performed based
on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not
imply that Industry Canada approved the equipment.
The CE mark, if present, declares that this equipment meets relevant EU Directives and Standards.
DANE TECHNOLOGIES, INC.
QUICKART 2000
OWNER’S MANUAL
7105 Northland Terrace, Minneapolis, MN 55428 / 888-544-7779 / 763-544-7779 / Fax 763-544-4234
www.danetechnologies.com
970-005 rev 10-10-05
PROGRAMMING THE REMOTE CONTROL
Each hand-held remote control transmitter operates on a unique pre-programmed code. For the
QuicKART to operate in the Remote Mode, the receiver, which is in the beacon tower, must be
programmed to match the hand held remote control. Every time the batteries in the remote
control are replaced, the remote control needs to be reprogrammed to match the receiver
code in the beacon tower. If the QuicKART stops responding to the remote control, check
the status of the remote battery by depressing one of the remote buttons. If the red LED
light does not illuminate, change the battery and reprogram the remote control as follows:
1) Turn on the QuicKART.
2) Switch to "RADIO" on the control panel.
3) Hold remote about arms length from the beacon post.
4) Simultaneously push these three buttons:
• Rubber button located on the underside of the square box
on the beacon post (see pages 15 and 16);
• Brake button on the hand-held remote (page 22);
• Horn button on the hand-held remote (page 22).
5) The horn should sound indicating the reprogram is complete and the QuicKART is
ready for operation.
6) If the horn did not sound, retry the above steps making sure that the switch on the
control panel is on "RADIO". If the horn still did not sound, you can also determine if
the reprogram was successful by pressing the slow button on the remote to see if the
QuicKART now responds to the remote signal.
DANE TECHNOLOGIES, INC.
QUICKART 2000 SERIES
OWNER’S MANUAL
7105 Northland Terrace, Minneapolis, MN 55428 / 888-544-7779 / 763-544-7779 / Fax 763-544-4234
www.danetechnologies.com
970-005 rev 10-10-05
28

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Page Mode                       : UseNone
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:9cfc80d9-4781-42ae-a1f1-b13d9ae403a6
Producer                        : Neevia docuPrinter Pro v5.1 (http://neevia.com)
Modify Date                     : 2005:11:17 17:10:06-08:00
Create Date                     : 2005:10:27 10:39:32-06:00
Creator Tool                    : Neevia docuPrinter Pro
Metadata Date                   : 2005:11:17 17:10:06-08:00
Document ID                     : uuid:11f96af8-9a89-4e96-9502-5359285d7de6
Format                          : application/pdf
Title                           : Microsoft Word - 970-005 QK2000 Owner Manual 10-10-05
Creator                         : Neevia docuPrinter Pro

EXIF Metadata provided by EXIF.tools