Danfoss Drives LCP-103 VLT Wireless Communication Panel LCP103 User Manual instructions

Download:
Mirror Download [FCC.gov]
Document ID	3657011
Application ID	C2reqczs0ToFCDivnLUcbg==
Document Description	User manual instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.21kB (252657 bits)
Date Submitted	2017-11-29 00:00:00
Date Available	2018-05-28 00:00:00
Creation Date	2017-10-13 11:13:13
Producing Software	Acrobat Distiller 9.5.5 (Windows)
Document Lastmod	2017-10-17 14:56:30
Document Title	User manual instructions
Document Creator	AH Formatter V6.2 MR8 (6,2,2015,0414) for Windows (x64)

Installation Instructions
VLT® Wireless Communication Panel LCP 103
VLT® FC Series FC 102, FC 103, FC 202,
FC 301/FC 302, and LD 302
NOTICE
1.1.1 Items Supplied
•
•
VLT® Wireless Communication Panel LCP 103.
Gasket
Illustration 1.1 VLT® Wireless Communication Panel LCP 103
1.1.2 Compatible Drive Series
NOTICE
Compatible drives have a white USB port.
• VLT® HVAC Drive FC 102
•
•
•
•
VLT® Refrigeration Drive FC 103
VLT® AQUA Drive FC 202
VLT® AutomationDrive FC 301/FC 302
VLT® Lift Drive LD 302
1.1.3 Approvals and Certifications
FCC ID: 2ANSELCP-103
FCC COMPLIANCE NOTICE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by 1 or more
of the following measures:
•
•
Reorient or relocate the receiving antenna.
•
Connect the equipment into an outlet on a circuit
different from that to which thereceiver is
connected.
•
Consult the dealer or an experienced radio/
television technician for help.
Increase the separation between the equipment
and receiver.
Modifications: Any modifications made to this device that
are not approved by Danfoss may void the authority
granted to the user by the FCC to operate this equipment.
RF EXPOSURE COMPLIANCE
This portable transmitter with its antenna has shown
compliance with FCC’s SAR limits for general population/
uncontrolled exposure. The maximum listed SAR level is 0.22
W/kg (body). The antenna used for this device must not be
co-located or operating in conjunction with any other
antenna or transmitter.
1.1.4 Installation
NOTICE
The VLT® Wireless Communication Panel LCP 103 is hotpluggable and can be connected when the drive is powered
on.
1.
Mount the LCP 103 in the LCP input plug on the
drive.
2.
Search for MyDrive® Connect in Google Play or Apple
Store.
Danfoss A/S © 10/2017 All rights reserved.
MI38V202
LED
Pattern
Description
Flashing Connection pairing successful.
Wi-Fi
Illustration 1.2 MyDrive® Connect Launch Icon
Alarm
3.
Download and install the MyDrive® Connect App.
Solid
The smart device is connected and communi-
white
cation is OK.
Flashing An alarm has occurred.
red
Warn
NOTICE
white
Solid
A warning has occurred.
yellow
Start pairing within the first 10 minutes after the installation. Failing to do so closes the broadcast or wireless
identification due to security limits with default passwords.
To reconnect, power cycle the drive, or remove and
reconnect the LCP 103.
MS,
NS1,
NS21)
Flashing Identification of the drive when initiated through
magenta a winking command.
Flashing Incompatible drive (LED flashes 3 times and then
orange
remains on).
Table 1.1 Descriptions, LED Indicators
1.1.5 Connection Procedure
1) MS=module status, NS1=network status 1, NS2=Network status 2.
NOTICE
1.1.7 Safe Control
The wireless SSID is the Danfoss serial ID of the drive. For
example, Danfoss_019223G455 is the default wireless SSID
for a drive with the serial number 019223G455. The serial
number is on the product nameplate, but is also visible in
parameter 15-51 Frequency Converter Serial Number.
Wireless SSID
Danfoss_019223G455
Default password
Danfoss1933
1.
2.
Open the app and establish the Wi-Fi connection, see
Table 1.1 for descriptions of the white Wi-Fi LED.
When prompted, change the default password due to
security restrictions. The password must be at least 8
and maximum 63 characters.
NOTICE
If the password is not changed, it leaves only 10 minutes for
connecting and performing Drive operations. After this, the
wireless connection closes.
Reset password
If the wireless SSID and password are forgotten, access
parameter group 30-9 Wifi LCP via MCT 10 Set-up Software or
LCP 102.
1.1.6 LED Pattern
The safe control parameter allows the drive to decide the
motor behavior if the smart device, for example a tablet,
communication is lost. If the limits are set to [1] Stop motor,
the motor stops. If the limits are set to [0] Do nothing, the
motor continues to run. This is only applicable when the
motor is in Run state. The communication happens between
the MyDrive® Connect App and the VLT® Wireless Communication Panel LCP 103.
Parameter
Limits/options
Parameter 30-97 Wifi Timeout Action
[0] Do nothing
[1] Stop motor
1.1.8 Specifications
Standards
IEEE 802.11 b/g
Frequency range
2.4~2.4835 Ghz
Antenna
PCB-mounted chip antenna
Security
WPA2
Operating temperature
-25 °C to +50 °C (-13 °F to
+122 °F)
Operating humidity
5–95% RH, non-condensing
Operating mode
Access point
Ingress protection
IP20 (IP55 with gasket)
Electrical rating
5 V, 250 mA
Internal memory size
14 MB
LED
Pattern
Description
Dimensions (LxWxD) [mm (in)]
131.2 x 66.6 x 23 (5.1 x 2.6 x 0.9)
On
Solid
The drive is powered on (normal operation).
Weight [g (oz)]
85.3 (2.88)
Firmware update
MCT 10 Set-up Software version
4.10 or higher
green
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on
order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss
and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com
130R0814
MI38V202
*MI38V202*
10/2017

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Create Date                     : 2017:10:13 11:13:13+02:00
Creator Tool                    : AH Formatter V6.2 MR8 (6,2,2015,0414) for Windows (x64)
Modify Date                     : 2017:10:17 14:56:30+03:00
Metadata Date                   : 2017:10:17 14:56:30+03:00
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Format                          : application/pdf
Title                           : 
Document ID                     : uuid:8008c005-0727-45db-9bad-04899fa670bb
Instance ID                     : uuid:68b86cda-dc9b-41f2-8bf3-4c0bf8abe6cd
Page Mode                       : UseNone
Page Count                      : 2
Creator                         : AH Formatter V6.2 MR8 (6,2,2015,0414) for Windows (x64)

EXIF Metadata provided by EXIF.tools