Dascom Printer TD11250 Dot Matrix Printer User Manual 1125 UG 2011 06 22

Dascom Printer (Jiangmen) Co.,Ltd. Dot Matrix Printer 1125 UG 2011 06 22

UserManual.wiki >

Dascom Printer >

TD11250 User Manual HTML Version

Users Manual

User Guide 1125 Matrix Printer

Tally Dascom 1125

Important Safety Instructions (English)

Read the following instructions thoroughly before starting up your printer.

• Never carry out maintenance or repair work yourself. Always contact a qualified service technician.

• Keep this Operator’s Manual in a place which is easily accessible at all times.

• Place the printer on a solid and even base so that it cannot fall.

• Never place the printer in the vicinity of inflammable gas or explosive substances.

• Ensure the printer is connected to a socket with the correct mains voltage.

• Always disconnect the printer from the mains before opening the device to perform maintenance work or

remedy errors.

• Do not expose the printer to high temperatures, direct sunlight or dust.

• Keep all liquids away from the printer.

• Protect the printer from shock, impact and vibration.

• Make sure that the printer and computer are switched off before connecting the data cable.

• The print head will become very hot during printing; avoid contact with the print head after printing has

finished.

• Do not perform any operation or action in any way other than those provided in this manual. When in

doubt, contact your dealer or your customer support.

Tally Dascom 1125

Wichtige Sicherheitshinweise (German)

Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen.

 Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie

immer einen qualifizierten Servicetechniker.

 Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.

 Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.

 Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven

Stoffen auf.

 Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen.

 Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den

Netzstecker an der Steckdose ziehen.

 Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.

 Keine Flüssigkeiten mit dem Drucker in Berührung bringen.

 Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen.

 Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel

angeschlossen wird.

 Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen

lassen.

 Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab.

Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.

Tally Dascom 1125

III

Consignes importantes de sécurité (French)

Lire attentivement les instructions suivantes avant de mettre l’imprimante en service.

 Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un

dépanneur qualifié.

 Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.

 Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de

substances explosives.

 Ne connecter l’imprimante à une prise que lorsque la tension est correcte.

 Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et

toujours débrancher le connecteur secteur de la prise murale.

 Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la

poussière.

 Ne pas mettre l’imprimante en contact avec des liquides.

 Ne pas exposer l’imprimante à des chocs, impacts ou vibrations.

 S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de données.

 La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques

instants avant d’y toucher.

 N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel. En

cas de doute, veuillez contacter votre distributeur ou service après-vente.

Tally Dascom 1125

Indicazioni di sicurezza importanti (Italian)

Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni.

Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di

assistenza qualificato.

 Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.

 Collocare la stampante su una superficie stabile, per evitare che cada a terra.

 Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive.

 Collegare la stampante a una presa di corrente con tensione adeguata.

 Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il

connettore di rete dalla presa.

 Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere.

 Evitare il contatto della stampante con liquidi.

 Non esporre la stampante a colpi, scosse o vibrazioni.

 Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati.

 Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno

quindi lasciarla raffreddare qualche istante.

 Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In

caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.

Tally Dascom 1125

Instrucciones de seguridad importantes (Spanish)

Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio.

Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio

calificado.

 Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.

 Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.

 Nunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias explosivas.

 Asegure conectar la impresora sólo a un enchufe con un voltaje correcto.

 Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de

alimentación del enchufe.

 No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.

 No ponga la impresora en contacto con fluidos.

 Nunca exponga la impresora a sacudidas, choques o vibraciones.

 Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos.

 La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo algún

tiempo antes de tocarla.

 No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala en

el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio post-venta.

Tally Dascom 1125

Правила по технике безопасности. (Russian)

Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера.

 Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о

неисправностях квалифицированным сервисным техникам.

 Данная инструкция должна быть всегда доступна каждому пользователю.

 Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.

 Ни в коем случае не ставьте принтер вблизи легко воспламеняющихся газов и взрывчатых

веществ.

 Включайте принтер в розетку только с соответствующим напряжением.

 Если Вы хотите отключить принтер от напряжения, сначала выключите принтер сам и затем

выньте штекер из розетки.

 Берегите принтер от нагревания, от попадания на него прямых солнечных лучей и пыли.

 Не допускайте попадания жидкости на принтер.

 Нельзя подвергать принтер тряске, ударам и вибрации.

 Убедитесь, что принтер и компьютер выключены, только после этого соедините принтер с

компьютером.

 Печатающая головка нагревается во время работы принтера. Поэтому подождите какое-то

время, прежде чем дотронуться до нее.

 Пользуйтесь принтером так, как это написано в документации. Если у Вас возникают неясности,

обращайтесь с вопросами к Вашим продавцам или в сервисный центр.

Tally Dascom 1125

VII

Instruções Importantes sobre Segurança (Portuguese)

Leia as instruções de segurança antes de usar a impressora.

 Consulte sempre um técnico qualificado para executar uma reparação .

 Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas.

 Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias

explosivas.

 Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.

 Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.

 Não exponha a impressora a temperaturas altas ou luz solar direta.

 Não aproxime substâncias líquidas da impressora.

 Proteja a impressora de choques, impactos e vibrações.

 Desligue a impressora e o computador antes de conectar o cabo da rede.

 A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de tocá-la.

 Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida,

contate seu revendedor ou companhia de serviço.

Tally Dascom 1125

VIII

Önemli Güvenlik Talimatları (Turkish)

Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun.

 Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiye bir

uzman servis-teknisyenine haber verin.

 Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.

 Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren nesnelerin

yakınına koymayın.

 Yazıcı akım kablosunu sadece doğru gerilime sahip bir prize takın.

 Yazıcıyı şebeke ağından ayırmak istediğinizde, yazıcıyı kapatın ve ağ-fişini her zaman prizden çıkartın.

 Yazıcıyı ne yüksek ısılı ne de doğrudan güneş ışığına ve toza mâruz kalan mekânlarda bulundurun.

 Yazıcı hiçbir sıvı maddeyle temasta olmamalıdır.

 Yazıcı hiçbir sarsıntıya, darbeye veya titreşime mâruz kalmamalıdır.

 Veri kablosu bağlanmadan önce hem yazıcının hem de bilgisayarın kapalı olduklarından emin

olmalısınız.

 Yazıcının başı basma esnasında yüksek ısıya ulaşıyor. Bu yüzden lütfen dokunmadan önce kısa süre

soğumasını bekleyin.

 Yazıcının işletimi ve kullanımında bu dokümantasyondaki talimatların hiç dışına çıkmayın. Sorunlu

görünen hususlarda lütfen imâlatçınıza veya müşteri hizmetleri servisinize başvurun.

Tally Dascom 1125

TRADEMARK ACKNOWLEDGEMENTS

“IBM” is a trademark of International Business Machines Corporation.

“EPSON” is a trademark of Epson America Incorporated.

“DEC” is a trademark of Digital Equipment Corporation.

“Centronics” is a trademark of Centronics Data Computer Corporation.

“DOS” is a trademark of Microsoft Corporation.

“SAP” is a trademark of SAP AG.

“Windows”, “Windows 7”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows

2003/2008 Server”, “Windows XP” and “Windows Vista” are trademarks of Microsoft Corporation.

All other product names and company names appearing in this manual are the registered trademarks or

trademarks of the individual companies.

Tally Dascom 1125

TABLE OF CONTENTS

1 UNPACKING GUIDE ........................................................................................................................................ 1

PLACING THE PRINTER .......................................................................................................................................... 2

PRINTER COMPONENTS ........................................................................................................................................ 2

2 SETTING UP PRINTER .................................................................................................................................... 4

INSTALL RIBBON .................................................................................................................................................. 4

INSTALL THE SINGLE SHEET FEEDER ....................................................................................................................... 5

CONNECTING THE INTERFACE CABLE ...................................................................................................................... 5

CONNECTING THE MAINS POWER .......................................................................................................................... 6

INSTALLING THE WINDOWS DRIVER ........................................................................................................................ 7

3 PAPER INSTALLATION GUIDE ..................................................................................................................... 10

ADJUSTING THE PRINT GAP LEVER ....................................................................................................................... 10

FRICTION FEED HANDLING .................................................................................................................................. 11

TRACTOR FEED HANDLING .................................................................................................................................. 12

CONTINUOUS PAPER PLACEMENT ........................................................................................................................ 12

4 CONTROL PANEL OPERATION .................................................................................................................... 14

PANEL OPERATION ............................................................................................................................................. 16

Online State ............................................................................................................................................................ 17

Setup State ............................................................................................................................................................. 18

Power-On State ...................................................................................................................................................... 19

LANGUAGE SETUP .............................................................................................................................................. 20

5 PRINTER SETTING CHANGES ..................................................................................................................... 21

SYSTEM SETUP .................................................................................................................................................. 21

PRINT SETUP ..................................................................................................................................................... 21

PAGE SETUP ...................................................................................................................................................... 23

INTERFACE SETUP .............................................................................................................................................. 24

ADVANCED SETUP .............................................................................................................................................. 24

VERTICAL ALIGNMENT ........................................................................................................................................ 34

CHANGE PIN FUNCTION ...................................................................................................................................... 35

ADJUST PHYSICAL MARGINS ............................................................................................................................... 36

DASCOM PRINTER SETUP TOOL ........................................................................................................................... 38

6 MAINTENANCE ............................................................................................................................................. 39

CLEANING AND VACUUMING THE PRINTER ............................................................................................................. 39

CLEANING THE PAPER ROLLERS ........................................................................................................................... 39

7 TROUBLESHOOTING .................................................................................................................................... 41

PRINT QUALITY PROBLEMS AND SOLUTIONS ........................................................................................................ 41

PAPER HANDLING PROBLEMS AND SOLUTIONS ..................................................................................................... 42

OPERATING PROBLEMS AND SOLUTIONS .............................................................................................................. 42

Tally Dascom 1125

XII

ERROR INDICATIONS ON LEDS ............................................................................................................................ 43

DIAGNOSTIC FUNCTIONS .................................................................................................................................... 44

FIRMWARE UPDATE ........................................................................................................................................... 45

8 GENERAL SPECIFICATIONS ......................................................................................................................... 46

9 INTERFACES .................................................................................................................................................. 51

PARALLEL INTERFACE ......................................................................................................................................... 51

USB INTERFACE ................................................................................................................................................ 52

SERIAL INTERFACE ............................................................................................................................................. 52

10 CHARACTER SETS & CODE PAGES .......................................................................................................... 53

CHARACTER SETS .............................................................................................................................................. 53

INTERNATIONAL CHARACTER SETS ........................................................................................................................ 55

INTERNATIONAL CHARACTER SET COMMANDS ...................................................................................................... 55

CHARACTER TABLES ........................................................................................................................................... 56

CODE PAGE COMMANDS .................................................................................................................................... 58

CODE PAGE TABLES ........................................................................................................................................... 60

11 CONTROL CODES SUMMARY ................................................................................................................... 84

EPSON EMULATION COMMAND LIST .................................................................................................................... 84

IBM EMULATION COMMAND LIST ....................................................................................................................... 86

FCC STATEMENT ............................................................................................................................................. 88

Tally Dascom 1125

1 Unpacking Guide

 Place your packaged printer on a solid base.

 Make sure that the “Up” symbols point in the correct direction.

 Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging

material.

 Check the printer for any visible transport damage and missing items. If you find any transport

damage or if any accessories are missing, please contact your dealer. The following items should be

included:

o Printer

o Paper feed knob

o Paper feed tray

o Power cord

o Ribbon cartridge

o CD-ROM

o Installation Guide

Remove the packaging materials from the printer as follows:

1. Remove the tape on the paper feed lever.

2. Remove other visible tape on the printer.

3. Open and remove the top cover of the printer.

4. Remove the shipping cardboard from around the print head.

5. Install the paper feed knob.

Tally Dascom 1125

Placing the Printer

Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it

cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that

there is enough space for sufficient ventilation and for the printed output.

When selecting the printer location, observe the following additional instructions:

 Never place the printer near to any flammable gas or explosive substances.

 Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect

it from the sunlight with a curtain.

 When connecting a computer to the printer, make sure the maximum recommended cable length is not

exceeded.

 Ensure sufficient distance between the printer and any heating devices/radiators.

 Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty

environments.

 It is recommended the printer is installed in a position which reduces noise exposure to the work place

during printing.

Printer Components

Tally Dascom 1125

Component Function

Gap Lever Controls printing impact or density.

Adjusts the print gap lever according to the thickness of paper.

Paper Guides Adjusts positioning of single sheet paper.

Print Head 24-pin printing mechanism

Top Cover Protects print head and other components inside, and reduce noise.

Control Panel Shows printer status, for printer setup.

Paper Feed Lever Two positions: = continuous forms; = single sheet paper

Paper Feed Knob Manual feed or vertical positioning of paper

Power Switch Power printer ON or OFF

Ribbon Cartridge Install ribbon in the printer.

Ribbon Frame For guiding ribbon installation on print head.

Tractors For feeding and adjustment of continuous forms.

Power Receptacle Connects power cord to the printer.

Interface Connects interface cables from the host.

Tally Dascom 1125

2 Setting Up Printer

Install Ribbon

1. Ensure the power to the printer is off and the print gap lever “A” is set to the furthest open position. Move

the carriage to the centre of the print platen.

2. Install the recess positions  on the ribbon cassette into the printer mounting.

3. Press the ribbon frame  onto the print head.

4. Turn the ribbon knob  in clockwise direction until the ribbon fabric is taut. Move the carriage left and

right to ensure the carriage and ribbon fabric can move smoothly.

5. Ensure the print gap lever “A” is set to the original position.

6. Close the printer’s top cover. When printer is in operation, ensure the printer’s top cover is closed to keep

the noise level to a minimum.

Notes on Ribbon Cartridge Removal:

1. Eject any paper loaded in the printer.

2. Turn off the printer power.

3. Open and remove the top cover.

4. Lift up the tear bar.

5. Set the gap lever to the most open position labeled “RIBBON”.

6. Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed,

as the print head may be hot.

7. Remove the blue ribbon frame from the print head.

8. Use fingers to take hold of the handle on the ribbon cartridge firmly, and lift the cartridge upwards to

unlatch it. Some force may be needed to unlatch the cartridge.

Tally Dascom 1125

Install the Single Sheet Feeder

Install the single sheet feeder into the rear of the printer.

Connecting the Interface Cable

The 36-pin Centronics parallel, 25-pin serial RS-232C and USB ports are located at the rear of the printer.

IMPORTANT: Make sure the printer and the computer are switched off before connecting or disconnecting

the interface cable to prevent electrical damage to the interface ports.

Tally Dascom 1125

Connecting the Mains Power

Checking the printer voltage

Make sure that the device has been set according to your country’s power supply voltage. To do this, check

the rating plate at the back of the printer. Contact your dealer if the setting is incorrect.

Never switch on the printer if the voltage setting is incorrect; this may result in electrical

damage to the printer.

Make sure that the power switch

“A”, located to the right side of the

printer, is in the “O” (off) position.

Connect the power cord to the

power inlet of the printer. Connect

the power cord plug to a mains

socket. Switch on the printer.

Tally Dascom 1125

Installing the Windows Driver

(Windows 2000/2003/2008 Server/XP/Vista/7)

1. Your printer CDROM comes with

Windows drivers. Go to the Drivers

folder and run the Installer

“DriverSetup.exe”. You will see the

screen on the right. Click “Next” to

continue.

2. A list of ports available on your

system will be displayed as shown

on the right. Choose the desired

port to use. Click “Next” to

continue.

3. Select the desired printer model

as shown on the right. Click

“Next” to continue.

Tally Dascom 1125

4. Here you can choose whether to

set the driver as the system

default driver, and whether you

want to print the Test Page after

installation is completed. If the

driver had been installed before,

it would be listed in the white box

on the right. Select the listed

driver (if any) if you want to

replace it; otherwise a copy of

the driver will be installed. Click

“Next” to continue.

5. Click “Finish” to start the

installation process.

6. If the driver is not yet Microsoft

Certified, the message on the right

would appear. Click “Continue

Anyway”. (As we continue to

expand our product portfolio, not

all of our drivers may be certified

yet. Please check our website

www.dascom.com for the latest

certified drivers.)

Tally Dascom 1125

7. Installation in progress.

8. After installation is completed

successfully, you will see the

message on the right.

Tally Dascom 1125

3 Paper Installation Guide

The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include

envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into

the printer using the forms tractors. The printer is able to print 1~5 plies multipart paper.

Do not load paper that has been folded or is damaged, wrinkled, or curled.

Adjusting the Print Gap Lever

The print gap lever is on the left side of the printer inside the top cover. Take care to adjust the print gap lever

to a suitable position whenever you change the number of copies being printed. Using the wrong print gap

may cause print head damage or paper jams.

Paper type Weight (g/m2) / ply Thickness (mm) Gap lever position

Single sheet 52～100 0.06～0.12 1P～2P

2-ply 40～52 0.12～0.14

3-ply 40～52 0.17～0.22 3P～4P

4-ply 40～52 0.23～0.27

5-ply 40～52 0.28～0.33 5P

Change ribbon --- Above 0.45

Tally Dascom 1125

There are 2 paper feed modes: friction feed and tractor feed.

Friction Feed Handling

1. Move the paper-feed lever forward to “ ” for friction feed mode.

2. Adjust the print gap lever if necessary.

3. Raise the single sheet feeder until it locks into its mounting. Align the left paper guide with the mark on the

left of the single sheet feeder. Adjust the right paper guide to the width of the paper used.

4. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with the platen.

5. The paper should advance automatically to the print position. The printer is now ready to print in the online

state.

Tally Dascom 1125

Tractor Feed Handling

1. Move the paper-feed lever backward to “ ” for continuous paper position.

2. Adjust the print gap lever if necessary.

3. Raise the tractor doors and fit the first 3 paper holes onto the left tractor pins. Close the left tractor door. In

the same way, install the paper on the right tractor.

4. Adjust the right tractor to the width of the paper until the paper is flat. Do not stretch the paper too taut.

Push the right lock lever down to secure the right tractor in place.

5. Press the【Load/Eject】key to load the paper to the starting print position. The printer is now ready to print

in the online state.

Tally Dascom 1125

Continuous Paper Placement

1. Place the printer on a solid base. The minimum suitable height of the solid base is 75 cm.

2. Left and right positioning: The direction of continuous paper should be parallel with the paper guide. The

tolerance should be less than 3 cm.

3. Front and back positioning: The distance between the rear of printer and the wall should be more than 60

cm. To avoid paper jam, the distance between the continuous paper and the edge of desk should be

10~15 cm.

Tally Dascom 1125

4 Control Panel Operation

There are 4 switches S1~S4 and 4 LEDs L1~L4. The meaning and application of each switch and LED are

described below.

LED Indicators

“Power/Paper Out” LED:

On: Power on

Flashing: Paper out

Flashing + buzzer: Paper jam

“Online” LED:

On: The printer is in online state and ready to receive data from the computer.

Off: The printer is in offline state and cannot receive data.

Flashing: The printer is in setup state and cannot receive data.

“Tear Off” LEDs:

Flashing: Indicates continuous paper is at tear-off position; otherwise it indicates the selected font.

Control Panel Keys

“Online” Key:

This key switches the printer between online and offline states. Printing is stopped when the printer is

switched to offline state. When printer is switched to online state again, printing will resume.

When printer is offline, pressing it for 3 seconds or longer will enter the setup state. This is indicated by a

beep sound and the flashing Online LED. By pressing the Online key again will exit the setup state back

to offline state.

“Load/Eject” Key:

When paper is loaded, pressing this key will eject the paper (single sheet mode) or park the paper

(continuous paper mode). When paper is not loaded, pressing this key will load the paper to the starting

print position. In the setup state, this key performs a forward micro feed.

Tally Dascom 1125

“LF/FF” Key:

Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a

few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode). In

the setup state, this key performs a reverse micro feed.

“Tear Off” Key:

When online, this key will move any loaded continuous paper to the tear-off position. When in setup state,

this key is used to select the desired font.

Table 4.1

Font Selection Label L1 State L2 State

Draft Off Off

Draft Condensed Off Flash

Roman Off On

Sans Serif On Off

Courier On Flash

Prestige On On

Script Flash Off

Others (see Menu setting) Flash ON

Tear Off Flash Flash

Table 4.2

Switch Top Label Bottom Label

S1 Tear Off Font

S2 LF/FF Micro Feed

S3 Load/Eject Micro Feed

S4 Online 3sec

Table 4.3

LED Label

L3 Power/Paper Out

L4 Online

Tally Dascom 1125

Panel Operation

There are 3 states of operation: Online, Setup and Power On.

In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed,

Load/Eject, clear buffer and switch to offline state for access to Setup state.

In the Setup state, the keys provide font selection and micro feed functions.

To enter the Power On state, the user holds down a key or a combination of keys while powering up the

printer. This state provides the following functions: Language Setup, Main Menu setup, Hex-dump, print Main

Menu, access Service Menu, adjust page margins, restore factory defaults, and firmware update.

The followings describe the 3 states in details.

Legend:

[A] = press and hold switch A

{B} = press and then release switch B

[A]+ {B} = press switch B while holding A

Tally Dascom 1125

Online State

Function Name Switch

Operation LED Function Description

Tear Off {S1} L1, L2 flash

This is valid for tractor mode only. It feeds the form to the

tear-off position. After tearing off the form, printing starts

on the next TOF by:

 pressing S1 once, or

 receiving print data from the host.

LF {S2}

- Feeds a line with every press of S2.

FF [S2] -

By holding S2, the printer initially feeds a few lines; then

feeds the form to the next TOF for rear tractor or ejects

the form for cut sheets.

Load/Eject {S3} -

 Load: Automatically loads the paper (according to path

selection) when no paper is on the platen.

 Eject: For rear tractor, it retracts the form from the

platen to allow users to install cut sheets. (NOTE:

Users have to toggle the path selection lever.)

For cut sheets, it ejects the form on the platen.

Setup state [S4] > 3 secs L4 Toggles to Setup state. Indicated by flashing L4.

Clear Buffer [S4]+{S1} - Clears the print buffer and beeps once when completed.

Reset [S4]+[S1] for

longer time - Initializes the printer to the factory default settings. Beeps

3 times when completed.

Tally Dascom 1125

Setup State

Function Name Switch

Operation LED Function Description

Online state {S4} L4

Toggling to the Online state will cause the printer to go into a

ready-to-print state. Any changes made in Setup state will be

saved permanently. Lighting up L4 indicates the Online state.

Micro Up {S3} - Feeds up in 1/360” steps until the release of S3.

Micro Down {S2} - Feeds down in 1/360” steps until the release of S2.

Font Select {S1} L1, L2 Refer to Table 4.1 for details.

Tally Dascom 1125

Power-On State

Function

Name

Switch

Operation LED Function Description

Status Page /

Self Test [S4] -

Prints the printer settings and self-test pattern.

Pressing S1 can change the font.

Hex Dump [S3] L4

Beeps once to indicate going into hex dump mode:

 Prints data from host in hexadecimal representation.

 Lights up L4.

 Pressing S4 suspends the printing.

 When the hex dump has finished, pressing S4 forces the

printing of the last line of data, as any line termination

control code from host has no function.

 Pressing S1 can change the font.

 Switch off the power to terminate the hex dump.

Firmware

Update

[S1]+[S2]+

[S3]+[S4]

L1, L2,

L3, L4

 Alternate flashing of L3 and L4 indicates printer is ready

for firmware update. L1 and L2 are ON and OFF

respectively.

 When new firmware is being received, L3 and L4 are set

to ON. L1 flashes a few times and then sets to ON. L2

flashing indicates downloading in progress.

 When downloading is completed, the carriage returns to

home position. Printer initializes normally.

Tally Dascom 1125

Adjust Physical

Margins [S3]+[S4]

L1, L2,

L3, L4

 Flashing of L3.

 Lights up L4.and L3.

 Lights up L1 or L2 according to current fonts.

 Includes Adjust Fanfold Top Margin, Adjust Single Top

Margin, Adjust Fanfold Left Margin, Adjust Single Left

Margin and Adjust Tear-Off position

Service Menu [S1]+[S2]

 Flashing of L3.

 Lights up L4.and L3.

 Lights up L1 or L2 according to current fonts.

 Functions are: Vertical Alignment, Change Pin, and

Endless Self-Test.

Restore Factory

Defaults [S2]+[S3]+[S4] L1, L2,

L3, L4

 Flashing of L3 then extinguish.

 Lights up L4.

 Lights up L1 or L2 according to current fonts.

 Restore Factory Defaults parameters except Change Pin,

Vertical Alignment and Adjust Page Margin Parameters

Menu Setup /

EDS [S1]

Allows for Main Menu setting changes. Please read the

instructions printed on how to change settings when this

mode is activated. (EDS: Electronic DIP Switch)

Language

Setup [S2]+[S3]

Allows user to select one of the following languages:

English, German, Russian, Italian, French, Spanish and

Turkish. Factory default is English. Refer to Language Setup

section below for details.

Language Setup

The panel menu can display the following languages: English, German, Russian, Italian, French, Spanish and

Turkish. Factory default setting is English. To change it to another language, hold down the [LF/FF] and

[Load/Eject] keys on the panel and power-on. Upon exiting the Language Setup Menu, a listing of the current

configuration is printed, and this is followed by Main Menu Setup.

Below is an example of changing from English to German language:

Tally Dascom 1125

5 Printer Setting Changes

To meet your own print requirements, the printer configurations may be changed as follows: Hold down the

Tear Off key while powering on the printer, release the Tear Off key when the print head starts to move. The

printer will print out the current settings and then enter Main Menu setup state. Follow the instructions

printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been

powered off.

The Main Menu is grouped into 5 sub-menus: System Setup, Page Setup, Print Setup, Interface Setup and

Advanced Setup. A detailed description of the sub-menus is given below. The settings in bold and italic refer

to the default settings. The settings below are provided in the following order of languages: English,

German, Russian, Italian, French, Spanish and Turkish.

System Setup

System

Setup Valid Settings Function

Emulation ESC/P2, IBM 2390

Plus

Selects the printer emulation. This should be the same as the host

printer driver.

Auto CR

(IBM) Yes, No Yes: LF = LF+CR; No: LF = LF

(Applies to IBM emulation only)

Auto LF Yes, No Yes: CR = CR+LF; No: CR = CR

Print Dir Bi-Dir, Uni-Dir,

Auto

Auto: Text & graphics in bi-direction; double height in uni-direction.

Uni-Dir: Prints everything in uni-direction. Bi-dir: Prints everything in

bi-direction. Note: Top position print direction may be affected by Top

Print Dir setting.

Top Print

Dir Bi-Dir, Uni-Dir Bi-dir: Prints top position according to Print Dir setting. Uni-dir: Prints

top position in uni-direction regardless of Print Dir setting.

Impact Normal, Heavy Heavy: Higher impact force for multipart printing

IBM AGM Yes, No Selects the IBM graphic mode. Applies to IBM emulation only

Print Setup

Print Setup Valid Settings Function

Font (Others) OCR-B, OCR-A, ORATOR, GOTHIC, SOUVENIR

The setting here will only be

active when “Font” is set to

“Others” on control panel,

Pitch 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Controls the characters per

inch setting.

Zero 0,Ø Selects slashed or no-slash

zero.

Tally Dascom 1125

HS-Draft On, Off On: Prints High Speed Draft

when Draft font is selected.

Graphic

Speed Normal, Fast, Ultra

When printing 180x180 DPI

graphics: Normal – prints in

180x180 DPI, Fast – prints in

90x180 DPI, Ultra – prints in

60x180 DPI.

IBM Set 1/2 Set 1, Set 2 Selects the IBM character

set. 1: Normal; 2: Extended

Int'l Char Set

USA, France, Germany, UK, Denmark, Sweden, Italy,

Spain, Japan, Norway, Denmark II, Spain II, Latin AM,

Korea, Legal

14+1 international character

set selections.

Code Page

1. CP 437

2. CP 737

3. CP 850

4. CP 851

5. CP 852

6. CP 857

7. CP 858

8. CP 860

9. CP 861

10. CP 863

11. CP 864

12. CP 864 Extended

13. CP 865

14. CP 866 Cyrillic

15. CP 866 Bulgaria

16. CP 1250

17. CP 1251

18. CP 1252

19. CP 1253

20. CP 1254

21. 8859-1

22. 8859-1 (SAP)

23. 8859-2

24. 8859-5

25. 8859-7

26. 8859-9

27. 8859-15

28. BRASCII

29. Abicomp

National code page

selections.

Tally Dascom 1125

30. Roman8

31. Coax/Twinax

32. New-437

33. New-Dig 850

34. Old-Code 860

35. Flarro 863

36. 865 Hebrew

37. CP 1257

38. 866 Ukraine

39. 866 Kazakhstan

40. Kamenicky

41. Mazovia

42. CP 775

43. CRO-ASCII

44. Arabic Farsi

45. Arabic Urdo

46. Greek DEC

47. Greek ELOT 928

Character

Table Graphic Table, Italic Table Character table type

selection.

Page Setup

Page Setup Valid Settings Function

Line Per Inch 1, 2, 3, 4, 5, 6, 7, 8 Sets the line spacing

Fanfold Form Length 3",3.5",11/3", 4", 5", 5.5" 6",7",8",

8.5",11", 70/6", 12", 14", 17" Sets the page length for tractor mode

Fanfold Top Margin 0/60" … 10/60"…99/60" Sets the top margin for tractor mode. Due to

mechanical tolerance, 0/60” is not guaranteed.

Fanfold Bottom

Margin 0/60"…10/60"...30/60"

Sets the bottom margin for tractor mode. Due

to mechanical tolerance, 0/60” is not

guaranteed.

Single Form Length 3", 3.5", 11/3", 4", 5", 5.5", 6", 7",

8", 8.5", 11", 70/6", 12", 14", 17" Sets the page length for friction mode

Single Top Margin 0/60" … 10/60"…99/60" Sets the top margin for friction mode. Due to

mechanical tolerance, 0/60” is not guaranteed.

Single Bottom

Margin 0/60"…10/60"...30/60"

Sets the bottom margin for friction mode. Due

to mechanical tolerance, 0/60” is not

guaranteed.

Roll Paper Yes, No In friction mode, [LF/FF] will not eject the paper

and feed to next page. (Assume roll paper)

Perforation Skip Yes, No Skips printing on perforation area

Tally Dascom 1125

Auto Tear Manual, 0.5s, 1s, 2s, 3s, 4s, 5s

View1s, View2s, View3s

Specifies the waiting time before feeding the

page to tear-off position automatically. Manual:

Auto tear mode is off. View1s, View2s, View3s:

After printing is completed, the printer will feed

the paper until the last printed line is at the

tear-off position. (Applies to tractor mode only)

Interface Setup

Interface

Setup Valid Settings Function

Interface

Auto, Parallel, USB,

Serial

For multi-host connection. Auto: First come first served;

Parallel/USB/Serial: Serves the designated host only.

RAM Usage User Font, Buffer

User Font: Part of RAM is used for user download characters;

Buffer: Disables user character download function; uses RAM for

expanded buffer size up to 68KB.

I-PRIME Yes, No Yes: Host I-Prime signal resets the printer.

Protocol Xon/Xoff, DTR Serial RS-232C communication protocol selection.

Data

Length 8, 7 Number of data bits per data byte selection.

Stop Bit 1, 2 Number of stop bits per data byte selection.

Parity None, Odd, Even Selects the parity check mode.

Baud Rate

9600, 19200, 38400,

300, 600, 1200, 2400,

4800

Selects the baud rate (transmission speed).

Auto IF

Delay 10s, 30s Determines the waiting time before receiving data from another

interface.

CX Bid Yes, No

Yes: Sets the parallel interface of the printer to bidirectional

mode (IEEE 1284, Nibble mode), e.g. for Windows Plug & Play.

No: Sets the interface to compatibility mode in order to ensure

reliable operation with special external boxes.

Advanced Setup

Advanced Setup Valid Settings Function

Auto Load Manual, 0.5s, 1s, 1.5s, 2s

Specifies the waiting time before loading a cut

sheet automatically. Manual: Auto load mode is

off. (Applies to friction mode only.)

Paper Jam

Prevention Yes, No Flattens paper edges by carriage movement

before printing starts.

Paper End Detect Yes, No Yes: Detects paper out and halts printing;

otherwise, ignores paper out and continues

Tally Dascom 1125

printing.

Form Length Ctrl Software, Ignore Ignore: Ignores form length commands

Pitch Ctrl Software, Ignore Ignore: Ignores CPI commands

Font Ctrl Software, Ignore Ignore: Ignores font select commands

Quality Ctrl Software, Ignore Ignore: Ignores print quality commands

Buzzer Yes, No Yes: Sounds buzzer on all hardware errors

German (Deutsch)

System Setup Valid Settings

Emulation ESC/P2, IBM 2390 Plus

Auto CR (IBM) Ja, Nein

Auto LF Ja, Nein

Druck Dir Bi-Dir, Uni-Dir, Auto

Top Druck Dir Bi-Dir, Uni-Dir

Anschlag Normal, Stark

IBM AGM Ja, Nein

Druck Setup Valid Settings

Font (Andere) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR

Zeichenteilung 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS

Null 0,Ø

HS-Draft An, Aus

Graphikgeschw. Normal, Schnell, Ultra

IBM Set ½ Set 1, Set 2

Land

USA, Frankreich, Deutschland, UK, Dänemark, Schweden,

Italien, Spanien, Japan, Norwegen, Dänemark II, Spanien II,

Latein-Amerika, Korea, Legal

Zeichensatz CP 437, CP 857…

Zeichentabelle Graphik, Italic

Seiten Setup Valid Settings

Zeilen Pro Zoll 1, 2, 3, 4, 5, 6, 7, 8

Endlos Formularlänge 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"

Endlos Oberer Rand 0/60" … 10/60"…99/60"

Endlos Unterer Rand 0/60"…10/60"...30/60"

Einzel Formularlänge 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"

Einzel Oberer Rand 0/60" … 10/60"…99/60"

Einzel Unterer Rand 0/60"…10/60"...30/60"

Rollenpapier Ja, Nein

Tally Dascom 1125

Perforationssprung Ja, Nein

Abreissen Manuell, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s

Schnittstellen Setup Valid Settings

Schnittstelle Auto, Parallel, USB, Serial

I-PRIME Ja, Nein

Protokoll Xon/Xoff, DTR

Datenlänge 8, 7

Stopp Bit 1, 2

Parity None, Odd, Even

Baud Rate 9600, 19200, 38400, 300, 600, 1200, 2400, 4800

Auto IF Delay 10s, 30s

RAM Nutzung Ladbarer Font, Puffer

CX Bid Ja, Nein

Erweitertes Setup Valid Settings

Auto Laden Manuell, 0.5s, 1s, 1.5s, 2s

Papierstau Vorbeugung Ja, Nein

Papierende Detekt Ja, Nein

Formularlänge Strg Software, Ignoriere

Zeichenteilung Strg Software, Ignoriere

Font Strg Software, Ignoriere

Qualität Strg Software, Ignoriere

Summer Ja, Nein

Russian (Россия)

Системные установки Valid Settings

Эмуляция ESC/P2, IBM 2390 Plus

Авто CR (IBM) Да, Нет

Авто LF Да, Нет

Направление печати Двунаправленная, Однонаправленная, Авто

Направление печати загл. букв Двунаправленная, Однонаправленная

Удар Нормальный, Сильный

IBM AGM Да, Нет

Настройка печати Valid Settings

Дополнительный шрифт OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR

знаков/дюйм 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS

Перечеркнутый ноль 0,Ø

Высокая скорость Вкл, Выкл

Tally Dascom 1125

Скорость графики Нормальная, Быстрая, Очень быстрая

Символы IBM 1/2 Уст. 1, Уст. 2

Набор знаков

USA, France, Germany, UK, Дания, Sweden, Italy, Spain,

Japan, Норвегия, Дания II, Spain II, Латин

ская Америка, Korea, Legal

Кодовая таблица CP 437, CP 857…

Таблица знаков Графика, Курсив

Параметры страницы Valid Settings

Строк на дюйм 1, 2, 3, 4, 5, 6, 7, 8

Длина формы для непрерывной

бумаги 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"

Отступ сверху для непрерывной

бумаги 0/60" … 10/60"…99/60"

Отступ снизу для непрерывной бумаги 0/60"…10/60"...30/60"

Длина формы для отдельных листов 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14",

17"

Отступ сверху для отдельных листов 0/60" … 10/60"…99/60"

Отступ снизу для отдельных листов 0/60"…10/60"...30/60"

Рулонная бумага Да, Нет

Пропуск перфорации Да, Нет

Авто прогон Ручной, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s

Установки интерфейса Valid Settings

Интерфейс Авто, Паралел, USB, RS-232

Паралел. порт Да, Нет

Протокол RS-232 Xon/Xoff, DTR

Кол-во бит 8, 7

Стоп бит 1, 2

Четность Нет, Чет, Нечет

Скорость передачи данных 9600, 19200, 38400, 300, 600, 1200, 2400, 4800

Время ожидания 10s, 30s

Назначение RAM Пользов. шрифт, Буфер

CX Bid Да, Нет

Дополнительные установки Valid Settings

Автозагрузка Ручная, 0.5s, 1s, 1.5s, 2s

Датчик движ. бумаги Да, Нет

Датчик конца бумаги Да, Нет

Tally Dascom 1125

Контоль длины формы Програмный, Игнор.

Контроль знаков/дюйм Програмный, Игнор.

Контроль шрифта Програмный, Игнор.

Контроль качества Програмный, Игнор.

Звук Да, Нет

Italian (Italiano)

Menu Sistema Valid Settings

Emulazione ESC/P2, IBM 2390 Plus

Auto CR (IBM) Si, No

Auto LF Si, No

Direz. Stampa Bi-Dir, Uni-Dir, Auto

Top Print Dir Bi-Dir, Uni-Dir

Impatto Normale, Pesante

IBM AGM Si, No

Menù Stampa Valid Settings

Fonte (Altre) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR

Spaziatura 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS

Zero 0,Ø

HS-Bozza Si, No

Veloc. Grafica Normale, Veloce, Ultra

IBM Set 1/2 Set 1, Set 2

Set Carat. Int.

USA, Francia, Germania, Regno Unito, Danimarca, Svezia,

Italia, Spagna, Giappone, Norvegia, Danimarca II, Spagna II,

America Latina, Korea, Legal

Code Page CP 437, CP 857…

Tab.Carattere Tab. Grafica, Italico

Menù Pagina Valid Settings

Interlinea 1, 2, 3, 4, 5, 6, 7, 8

Lungh. Mod. Continuo 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"

Margine Sup. Continuo 0/60" … 10/60"…99/60"

Margine Inf. Continuo 0/60"…10/60"...30/60"

Lunghezza Foglio 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"

Margine Sup. Foglio 0/60" … 10/60"…99/60"

Margine Infer. Foglio 0/60"…10/60"...30/60"

Rullo Carta Si, No

Salto Perforazione Si, No

Autostrappo Manuale, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s

Tally Dascom 1125

Menù Interfacc. Valid Settings

Interfaccia Auto, Parallela, USB, Seriale

I-PRIME Si, No

Protocollo Xon/Xoff, DTR

Lunghezza dati 8, 7

Stop Bit 1, 2

Parità No, Dispari, Pari

Velocità 9600, 19200, 38400, 300, 600, 1200, 2400, 4800

Ritardo Auto IF 10s, 30s

Uso RAM Fonti utente, Memoria

CX Bid Si, No

Menù Avanzato Valid Settings

Autocaricamento Manuale, 0.5s, 1s, 1.5s, 2s

Previene Inceppamento Si, No

Rileva Fine Carta Si, No

Control. Lungh. Carta Software, Ignora

Control. Spaziatura Software, Ignora

Controllo Fonti Software, Ignora

Controllo Qualità Software, Ignora

Cicalino Si, No

French (Français)

Setup système Valid Settings

Emulation ESC/P2, IBM 2390 Plus

RC-Auto (IBM) Oui, Non

SL-Auto Oui, Non

Dir Impr. Bidir, Unidir, Auto

Sup. Dir Impr. Bidir, Unidir

Frappe Normal, Forte

IBM AGM Oui, Non

Setup impression Valid Settings

Polices (Autres) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR

Densités caract. 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS

Zéro 0,Ø

HS-Draft Oui, Non

Vitesse graphiq. Normal, Rapide, Ultra

IBM Set 1/2 Set 1, Set 2

Pays USA, France, Allemagne, Royaume-Uni, Denmark, Suède, Italie,

Tally Dascom 1125

Espagne, Japon, Norvège, Denmark II, Espagne II, Amerique

latine, Korea, Legal

Jeu de caractèr. CP 437, CP 857…

Tabl.de caract. Graphque, Italique

Setup page Valid Settings

Lignes par pouce 1, 2, 3, 4, 5, 6, 7, 8

Papier continu Longueur formulaire 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"

Papier continu Bord supérieure 0/60" … 10/60"…99/60"

Papier continu Bord inférieure 0/60"…10/60"...30/60"

Feuille à feuille Longueur formulaire 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"

Feuille à feuille Bord supérieur 0/60" … 10/60"…99/60"

Feuille à feuille Bord inférieur 0/60"…10/60"...30/60"

Papier du rouleau Oui, Non

Sauter la perforation Oui, Non

Coupe Auto Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s

Setup interface Valid Settings

Interface Auto, Parallel, USB, Serial

I-PRIME Oui, Non

Protocole Xon/Xoff, DTR

Long. de données 8, 7

Bits d’arrêt 1, 2

Parité None, Odd, Even

Vitesse baud 9600, 19200, 38400, 300, 600, 1200, 2400, 4800

Auto IF Delay 10s, 30s

Utilisation RAM User Font, Buffer

CX Bid Oui, Non

Setup élargi Valid Settings

Chargem. Autom. Manuel, 0.5s, 1s, 1.5s, 2s

Prévention bourrage Qui, Non

Détec.fin de pap Qui, Non

Long.formul.Strg Software, Ignorer

Densi.caract.Strg Software, Ignorer

Police Strg Software, Ignorer

Qualité Strg Software, Ignorer

Vibrateur Qui, Non

Tally Dascom 1125

Spanish (Español)

System Setup Valid Settings

Emulación ESC/P2, IBM 2390 Plus

Auto CR(IBM) Si, No

Auto LF Si, No

ModoImpresión Bi-Dir, Uni-Dir, Auto

ModoImp.Borde Bi-Dir, Uni-Dir

Impacto Normal, Fuerte

IBM AGM Si, No

Print Setup Valid Settings

Fuente (Otros) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR

Tamaño Letra 10cpp, 12cpp, 15cpp, 17cpp, 20cpp, PS

Cero 0,Ø

Alta Velocidad Activado, Desactivado

Imp. Grafica Normal, Rápido, Ultra

IBM Juego 1/2 Juego 1, Juego 2

Carácter Local

USA, Francia, Alemania, Reino Unido, Dinamarca, Suecia, Italia,

España, Japón, Noruega, Dinamarca II, España II,

AméricaLatina, Corea, Legal

Tabla Carácter CP 437, CP 857…

Tipo Tabla Tabla Gráfica, Italica

Page Setup Valid Settings

Lineas Por Pulgada 1, 2, 3, 4, 5, 6, 7, 8

Tamaño Papel Continuo 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"

Margen Sup. Pap Cont. 0/60" … 10/60"…99/60"

Margen Inf. Pap.Cont. 0/60"…10/60"...30/60"

Tamaño Hojas Sueltas 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"

Margen Sup. Folios 0/60" … 10/60"…99/60"

Margen Inf. Folios 0/60"…10/60"...30/60"

Rollo de Papel Si, No

Salto perforación Si, No

Mover a PosiciónCorte Manual, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s

Interface Setup Valid Settings

Interface Auto, Paralelo, USB, Serie

I-Prime Si, No

Tally Dascom 1125

Protocolo Xon/Xoff, DTR

LongitudDatos 8, 7

Bit Parada 1, 2

Paridad Ninguna, Impar, Par

Tasa Baudios 9600, 19200, 38400, 300, 600, 1200, 2400, 4800

Auto retraso 10s, 30s

Uso de RAM Font Usuario, Buffer

CX Bid Si, No

Advanced Setup Valid Settings

Auto Carga Manual, 0.5s, 1s, 1.5s, 2s

Prevención Atascos Si, No

Detección Fin Papel Si, No

Control Tamaño Papel Software, Ignorar

Control Tamaño Letra Software, Ignorar

Control Fuente Software, Ignorar

Control Calidad Software, Ignorar

Alarma Si, No

Turkish (Türkce)

Sistem Ayarı Valid Settings

Benzetim/Emulation ESC/P2, IBM 2390 Plus

Otom. Satırbaşı (IBM) Evet, Hayır

Otom. Satır besleme Evet, Hayır

Yazdırma yönü

ki-Yöne, Tek-Yöne, Otom.

Üstte yazdırma yönü

ki-Yöne, Tek-Yöne

Vuruş Normal, Güçlü

IBM AGM Evet, Hayır

Yazdırma Ayarları Valid Settings

Yazı Tipi (Diğer) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR

Karakter Sıklığı 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS

Sıfır 0,Ø

Yük.Hız-Taslak On, Off

Grafik Hızı Normal, Hızlı, Ultra

IBM Karakter Seti 1/2 Set 1, Set 2

Uluslararası Kar. Seti

Amerika Bir.Devleti, Fransa, Almanya, İngiltere, Danimarka,

İsveç, İtalya, İspanya, Japonya, Norveç, Danimarka II, İspanya

II, Latin Amerika, Korea, Legal

Kod Sayfası CP 437, CP 857…

Tally Dascom 1125

Karakter Tablosu Grafik Tablosu, İtalik

Sayfa Düzeni Ayarı Valid Settings

İnç başına satır 1, 2, 3, 4, 5, 6, 7, 8

Sürekli-kağıt Form Uzunluğu 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"

Sürekli-kağıt Üst kenar boşluğu 0/60" … 10/60"…99/60"

Sürekli-kağıt Alt kenar boşluğu 0/60"…10/60"...30/60"

Tek-kağıt Form uzunluğu 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"

Tek-kağıt Üst kenar boşluğu 0/60" … 10/60"…99/60"

Tek-kağıt Alt kenar boşluğu 0/60"…10/60"...30/60"

Rulo kağıt Evet, Hayır

Delik atlama Evet, Hayır

Otom. Koparma Elle/Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s

Arabirim Ayarları Valid Settings

Arabirim Otom., Paralel, USB, Seri

I-Prime Evet, Hayır

İletişim Kuralları Xon/Xoff, DTR

Veri Uzunluğu 8, 7

Durma Biti 1,2

Eşlik Yok, Çift, Tek

Baud Hızı 9600, 19200, 38400, 300, 600, 1200, 2400, 4800

Otom. Arabirim gecikmesi 10s, 30s

RAM Kullanımı Kullanıcı Yazı Tipi, Arabellek

CX Bid Evet, Hayır

Geliştirilmiş Ayarlar Valid Settings

Otom. Yükleme Elle/Manuel, 0.5s, 1s, 1.5s, 2s

Kağıt Sıkışmasını Önleme Evet, Hayır

Kağıt Sonunu Algılama Evet, Hayır

Form Uzunl. Kont. Yazılım, Yoksay

Karak.Sıkl. Kont. Yazılım, Yoksay

Yazı Tipi Kont. Yazılım, Yoksay

Kalite Kont. Yazılım, Yoksay

Alarm Zili Evet, Hayır

Tally Dascom 1125

Vertical Alignment

The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing.

Adjust Vertical Alignment Procedure:

1. Enter the Service Menu by holding down the【Tear/Off】and【LF/FF】keys while powering up.

2. Load paper.

3. The printer will print as follows:

Service Menu

【LF/FF】= OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit

Current Setting：Vertical Alignment

4. Press【LF/FF】key to select the current setting. The printer will print as follows:

Vertical Alignment

【LF/FF】= OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit

Please select Paper Type：Single Ply

For single ply paper, press【LF/FF】key to select. For multipart paper, press 【Load/Eject】key to go

to “Multipart”，then press【LF/FF】key to select.

5. If single ply is selected for paper type, the following will print:

Single Ply

Current Print Mode: LQ

Press 【Load/Eject】key to scroll to other print modes if required.

6. If LQ is selected, the following will print:

【LF/FF】= lower ½ to left 【Load/Eject】= lower ½ to right 【Online】= Exit

LQ -2:

||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

Pressing 【LF/FF】or 【Load/Eject】 key will allow you to adjust the alignment of the vertical lines

Tally Dascom 1125

printed above.

7. Once the setting which gives the best alignment is found, press 【Online】 key to exit current level.

Printer will print “Save settings? Yes”. Press 【LF/FF】 key to save setting. Press 【Online】 key a few

times until the printer exits the Service Menu.

Change Pin Function

When printer has been used for a long time or the print volume is high, the frequently used print head pins

may fail. The Change Pin function enables the user to continue using the printer for a while without

compromise in print quality until a suitable print head replacement is available. This function will reduce the

print speed if activated.

Change Pin Procedure:

1. Enter the Service Menu by holding down the【Tear/Off】and【LF/FF】keys while powering up.

2. Load paper.

3. The printer will print as below:

Service Menu

【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit

Current Menu：Vertical Alignment

Press 【Load/Eject】 key to scroll to “Change Pin”，then press 【LF/FF】 key to select. The status

of each pin will be printed as follows:

Change Pin

1 ---------- Is this pin OK? Yes / No

2 ---------- Is this pin OK? Yes / No

3 ---------- Is this pin OK? Yes / No

24 ---------- Is this pin OK? Yes / No

Press 【Load/Eject】 key to choose whether the pin is Ye s or No，then press 【LF/FF】 key to confirm

selection.

4. When all the 24 pins are evaluated, press 【Online】. The printer will print “Save settings? Yes”. Press

【LF/FF】 key to confirm selection. Press 【Online】 key a few times until the printer exits the Service

Menu.

Tally Dascom 1125

Adjust Physical Margins

Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once

these settings are changed, resetting the printer to factory defaults will not initialize these settings back to

the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary.

Adjust Top Margin Procedure:

1. Enter the Adjust Page Margins function by holding down the【Load/Eject】and【Online】keys while

powering up until the printer beeps twice.

2. Load paper.

3. The printer will print as below:

Adjust Page Margins:

【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit

Current Setting: Adjust Fanfold Top Margin

Press【LF/FF】key to confirm selection if the paper used is fanfold type. The printer will print as

follows:

Procedure：

Install fanfold paper to tractors

【LF/FF】 = Add 【Load/Eject】 = Reduce 【Online】 = Exit

Each step is 0.5 mm

Function of keys:

【Te a r O f f 】key: Decrease 0.5mm

【Load/Eject】key: Increase 0.5mm

4. Press 【LF/FF】 key, printer will print “Save settings？Ye s ”. Press 【Load/Eject】 key to choose Yes

or No，then press 【LF/FF】 key to confirm selection and exit “Adjust Page Margins” mode by

pressing 【Online】. The print head moves to the left side and the printer beeps twice, then the print

head moves to the middle position.

Adjust Left Margin Procedure:

1. Enter the Adjust Page Margins function by holding down the【Load/Eject】and【Online】keys while

powering up until the printer beeps twice.

2. Load paper.

3. The printer will print as below:

Adjust Page Margins:

【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit

Current Setting: Adjust Fanfold Top Margin

4. Press【Load/Eject】key until the current setting is “Adjust Fanfold Left Margin”. Press【LF/FF】key to

confirm selection if the paper used is fanfold type. The printer will print as follows:

Adjust Fanfold Left Margin 0

Tally Dascom 1125

Function of keys:

【Te a r O f f 】key: Decrease 0.5mm

【Load/Eject】key: Increase 0.5mm

5. Press 【LF/FF】 key, printer will print “Save settings？Ye s ”. Press 【Load/Eject】 key to choose Yes

or No，then press 【LF/FF】 key to confirm selection and exit “Adjust Page Margins” mode by

pressing 【Online】. The print head moves to the left side and the printer beeps twice, then the print

head moves to the middle position.

Adjust Tear-Off Position Procedure:

1. Enter the Adjust Page Margins function by holding down the【Load/Eject】and【Online】keys while

powering up until the printer beeps twice.

2. Load fanfold paper.

3. The printer will print as below:

Adjust Page Margins:

【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit

Current Setting: Adjust Fanfold Top Margin

4. Press【Load/Eject】key until the current setting is “Adjust Tear-Off Position”. Press【LF/FF】key to

confirm selection. The printer will print as follows:

Procedure：

Install fanfold paper to tractors

【LF/FF】 = Add 【Load/Eject】 = Reduce 【Online】 = Exit

Each step is 0.5 mm

Function of keys:

【Te a r O f f 】key: Decrease 0.5mm

【Load/Eject】key: Increase 0.5mm

5. Press 【LF/FF】 key, printer will print “Save settings？Ye s ”. Press 【Load/Eject】 key to choose Yes

or No，then press 【LF/FF】 key to confirm selection and exit “Adjust Page Margins” mode by

pressing 【Online】. The print head moves to the left side and the printer beeps twice, then the print

head moves to the middle position.

Tally Dascom 1125

Dascom Printer Setup Tool

In the CDROM is a software utility called “Dascom Printer Setup”. This application enables a convenient,

simple and fast way to control your printer without touching any keys on the operation panel.

1. Start the tool installation by double clicking the “Dascom Printer Setup.exe”.

2. Connect the printer to the system using USB cable

3. Power up the printer.

4. Load paper into the printer. (Note: The tool cannot get connected to the printer when the printer is

offline.)

5. Run the tool from the Windows Start menu by selecting All Programs, then Dascom Printer Setup,

and then Tally Dascom Printer Setup.

6. For more information on how to use the tool, go to the Help menu and select User Guide.

Tally Dascom 1125

6 Maintenance

Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is

required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is

sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly

back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact

your dealer to determine whether lubrication may be necessary.

Switch printer off and unplug the power cord from

the mains before doing any maintenance work.

Cleaning

The housing and the top cover of the printer help protect it against dust, dirt, and other contaminants.

However, paper produces small particles that accumulate inside the printer. This section explains how to clean

and vacuum the printer and how to clean the paper bail rollers. It is easier to clean the printer when the cover

is open.

Cleaning and Vacuuming the Printer

If the print head carriage does not move smoothly back and forth or paper particles have accumulated in the

printer, clean the printer.

To clean and vacuum the printer:

1. Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer

power cord.

2. Using a soft vacuum brush, vacuum the exterior of the printer. Also vacuum the cut sheet edge.

3. Use a soft, damp cloth to wipe the exterior of the printer, including the cover. A mild detergent may be

used. Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer.

4. Open the cover of the printer and remove the ribbon cartridge. Using a soft vacuum brush, gently vacuum

the platen, the print head carriage and shaft, and surrounding areas. You can easily slide the print head to

the left or right when the power is off. Be careful not to press too hard on the flat head cable that extends

from the print head carriage.

5. Re-install the ribbon cartridge.

6. Remove the single sheet feeder and clean the form tractors and the surrounding areas.

7. Re-install the single sheet feeder.

Cleaning the Paper Rollers

Clean the platen and paper bail rollers occasionally or when stains or smudges appear on the paper. Use a mild

detergent as appropriate. Do not use alcohol to clean the platen or the rollers. Alcohol may cause the rubber to

harden.

To clean the rollers and the platen:

1. Apply a small amount of water to a soft cloth. Avoid spilling liquid inside the printer.

2. Place the cloth against the platen and manually rotate the paper feed knob.

3. Repeat this procedure for each roller.

Tally Dascom 1125

4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed

knob.

Tally Dascom 1125

7 Troubleshooting

Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on

some of the common problems you may encounter and how you may solve them. If you encounter problems

that you cannot resolve, contact your dealer or service partner for assistance.

Print Quality Problems and Solutions

Problem Solution

Printing is too light or too dark.

• Make sure that the ribbon cartridge is properly installed and that

the ribbon feeds smoothly.

• Replace the ribbon if necessary.

• Make sure that the print gap lever is set for the thickness of your

paper.

Smears and stains appear on the

page.

• Make sure that the print gap lever is set for the thickness of your

paper.

• Check for ribbon wear. Replace the ribbon if necessary.

• Check whether the tip of the print head is dirty. Clean the head

with a soft cloth if necessary.

• The print head may need to be replaced.

Printing is erratic or the wrong

characters are printed. Many “?”

or unexpected characters are

printed.

• Make sure that the interface cable is securely connected to both

the printer and computer.

• Make sure that the printer driver selected in your software is the

same as the emulation selected on the printer.

• Check the length of the interface cable. (Maximum Parallel &

USB: 2 meters, Serial: 15 meters)

• Try another interface cable.

The page is blank. • Make sure that the ribbon cartridge is properly installed.

• Make sure the gap lever is set correctly.

Printing is vertically misaligned

(jagged).

Use the printer's vertical alignment function to check the vertical

print alignment. If necessary, adjust the print alignment.

The top margin is wrong. • Check the application top margin setting.

• Adjust the Top Margin setting in Page Setup menu if necessary.

Lines are double spaced instead of

single spaced. Change the Auto LF setting in the System Setup menu to No.

The printer overprints on the same

line. Change the Auto CR setting in the System Setup menu to No.

The next print line starts where

the previous line ended instead of

at the left margin.

Change the Auto CR setting in the System Setup menu to Yes.

Tally Dascom 1125

Paper Handling Problems and Solutions

Problem Solution

Paper cannot be loaded or fed.

• Make sure that the paper select lever located on the top right of

the printer is set correctly. Move the lever to the front for single

sheets or to the rear for continuous forms.

• Make sure that the paper covers the paper-out sensor.

Paper jams while loading.

• Turn off the printer and remove the jammed paper. Remove any

obstructions from the paper path.

• Make sure that the Print Gap lever is set for the thickness of

your paper.

• Make sure that the paper is not folded, creased, or torn.

• Make sure that the left and right tractors are set so that the

continuous forms are stretched taut.

Paper jams while printing.

• Turn off the printer and remove the jammed paper. Remove any

obstructions from the paper path.

• Make sure that the Print Gap lever is set for the thickness of

your paper.

• For continuous forms, make sure that the incoming and

outgoing paper stacks are correctly placed. Paper should feed

straight.

Paper slips off the forms tractors

or the perforated holes of the

paper tear during printing.

Make sure that the forms tractors are positioned correctly for the

width of your paper and that the perforated holes of the paper fit

directly over the tractor pins.

Operating Problems and Solutions

Problem Solution

The power does not turn on.

• Check whether the mains voltage is correct.

• Make sure that the power cord is securely connected to both

the printer and the mains power outlet.

• Make sure that the power outlet is functional. If not so, use

other outlet.

• Turn the power off. Wait a minute and then turn the printer on

again. If the printer still has no power, contact your dealer.

Tally Dascom 1125

The printer is on but it will not

print.

• Make sure that the Online indicator is lit.

• If you use the interface cable, make sure it is securely

connected to both the printer and the computer.

• Make sure paper is loaded.

• Run the printer Status Page. If printing executes normally, the

problem is caused by: the interface, the computer, incorrect

printer settings, or incorrect software settings.

• Make sure that the printer driver selected in your software is the

same as the emulation selected on the printer.

Paper select lever error

If paper is loaded and the paper select lever is moved to the

incorrect position, the printer turns offline, and the buzzer sounds

continuously. Switch the paper select lever back to its correct

position.

Printer Failures

A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the

printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner.

Error Indications on LEDs

Error Description Operation

Status

Paper

Out LED

Online

LED

Tear Off

LED

Buzzer

Sound

Paper out Normal Flash Off No change Once

Paper jammed Suspend Flash Off Flash Once

Friction feed /Tractor feed Suspend On Off Flash Continuously

Print head hot Normal On Flash No change --

Carriage initial position Stop Off Off Flash Once

Memory Stop Off Off Flash --

EEPROM Normal Off Flash No change Once

CMOS chip Stop Off Flash Flash --

Tally Dascom 1125

Diagnostic Functions

The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment.

 Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware

is functional, any problems you are having are probably caused by incorrect printer settings, incorrect

software settings, the interface, or the computer.

 HEX-DUMP MODE: Allows you to determine whether the computer is sending the correct commands

to the printer, and whether the printer is executing the commands correctly. This function is useful to

programmers or others who understand how to interpret hex dumps.

 PRINTING ALIGNMENT ADJUSTMENT: Allows you to check and, if necessary, correct the printer’s

vertical line print alignment in bi-directional mode.

For details on using these functions, please refer to chapters 4 and 5.

Tally Dascom 1125

Firmware Update

Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained

from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is

strongly recommended to print the Main Menu page to keep a record of the old settings.

Note: Firmware update should only be performed by an authorized service person. We disclaim any

responsibility for any damage caused if it is performed by any other person.

To load new firmware, proceed as follows:

1. Switch off the printer. Connect your PC to the parallel port on the printer.

2. Press and hold down all 4 keys (S1, S2, S3, S4) while powering on the printer.

3. Alternate flashing of L3 and L4 LEDs indicates printer is ready for firmware update. L1 and L2 LEDs

are ON and OFF respectively.

4. Go to the DOS prompt window. Copy the firmware file (with extension .MOT) to your printer as

follows:

COPY /B <filename>.mot PRN

5. When new firmware is being received, L3 and L4 LEDs are set to ON. L1 LED flashes a few times,

then sets to ON. L2 LED flashing indicates downloading in progress.

Note: Do not interrupt the downloading process to prevent possible flash memory corruption.

6. When downloading is completed, the carriage returns to home position. Printer initializes normally.

Alternatively, you can use the Firmware Flash Tool version 3.5 or higher which is available in the CDROM and

our website as well. Upon starting up the tool, choose the correct file and press "Update".

Tally Dascom 1125

8 General Specifications

Print System Mono-chrome serial impact dot matrix

Print Technology Uni-/bi-directional logic seeking for text and graphics

Print Speed

Pitch HS Draft Draft LQ (CPS/DPI)

10 CPI 375/80H 250/120H 83/360H

12 CPI 300/120H 300/120H 100/360H

15 CPI 375/120H 375/120H 125/360H

17.1 CPI 426/120H 426/120H 142/360H

20 CPI 498/120H 498/120H 166/360H

Font Matrix

Pitch HS Draft Draft LQ (Matrix/DPI)

10 CPI 8x24/80H 12x24/120H 36x24/360H

12 CPI 10x24/120H 10x24/120H 30x24/360H

15 CPI 8x16/120H 8x16/120H 24x16/360H

17.1 CPI 7x24/120H 7x24/120H 21x24/360H

20 CPI 6x24/120H 6x24/120H 18x24/360H

Proportional Nx24/360H Nx24/360H Nx24/360H

Print Head

Number of pins: 24 pins

Firing frequency: Normal mode: 1500 Hz

Pin diameter: 0.2 mm

Life: 400 million strokes/pin @ Draft mode

Graphics 8-bit mode: 8V x 60H, 80H, 90H, 120H, 240H (DPI)

24-bit mode: 24V x 60H, 90H, 120H, 180H, 360H (DPI)

Paper

Feed Speed Continuous feed: 5.0 IPS (inches per second)

Resolution 360 x 360 DPI maximum

Printable

Columns

Characters per line (CPL)

10 CPI: 80 CPL

12 CPI: 96 CPL

15 CPI: 120 CPL

17.1 CPI: 137 CPL

20 CPI: 160 CPL

Tally Dascom 1125

Built-In Fonts

Bitmap Fonts:

1. Draft 10, 12, 15, 17, 20 CPI

2. Roman 10, 12, 15, 17, 20 CPI, Proportional

3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional

4. Courier 10, 12, 15, 17, 20 CPI, Proportional

5. Prestige 10, 12, 15, 17, 20 CPI

6. OCR-B 10, 12, 17, 20 CPI

7. OCR-A 10, 12, 17, 20 CPI

8. Orator 10, 12, 15, 17, 20 CPI, Proportional

9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional

10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional

11. Script 10, 12, 15, 17, 20 CPI

Barcodes

1. EAN-13

2. EAN-8

3. Interleaved 2 of 5

4. UPC-A

5. UPC-E

6. Code 39

7. Code 128

8. POSTNET

9. Codabar

10. Industrial 2 of 5

Code Pages

1. CP 437

2. CP 737

3. CP 850

4. CP 851

5. CP 852

6. CP 857

7. CP 858

8. CP 860

9. CP 861

10. CP 863

11. CP 864

12. CP 864 Extended

13. CP 865

14. CP 866 Cyrillic

15. CP 866 Bulgaria

16. CP 1250

17. CP 1251

18. CP 1252

19. CP 1253

20. CP 1254

Tally Dascom 1125

Code Pages

21. 8859-1

22. 8859-1 (SAP)

23. 8859-2

24. 8859-5

25. 8859-7

26. 8859-9

27. 8859-15

28. BRASCII

29. Abicomp

30. Roman8

31. Coax/Twinax

32. New-437

33. New-Dig 850

34. Old-Code 860

35. Flarro 863

36. 865 Hebrew

37. CP 1257

38. 866 Ukraine

39. 866 Kazakhstan

40. Kamenicky

41. Mazovia

42. CP 775

43. CRO-ASCII

44. Arabic Farsi

45. Arabic Urdo

46. Greek DEC

47. Greek ELOT 928

International

Character Sets

1. USA

2. France

3. Germany

4. UK

5. Denmark I

6. Sweden

7. Italy

8. Spain I

9. Japan

10. Norway

11. Denmark II

12. Spain II

13. Latin America

14. Korea

15. Legal

Tally Dascom 1125

Line Spacing 1/6", 1/8", n/60", n/180", n/360"

Paper

Specifications

Paper

Specifications

Cut Sheet

Fanfold Paper

Single ply Multi-part

Width:

76.2mm～256.5mm

（3"～10.1"）

Length:

101.6mm～363.2mm

（3.9"～14.3"）

Width: 76.2mm～254mm (3"～10"）

Length: 101.6mm min (4" min)

Weight: 52～100g/㎡

Thickness:

0.065～0.14mm

(0.0026"～0.0055”)

Weight: 52～100 g/㎡

Thickness:

0.065～0.14mm

(0.0026"～0.0055")

Weight: 40～58g/㎡

Thickness: 0.45 mm max

(0.0177” max)

Paper Handling

Feeding method: Friction and Tractor

Paper path: Cut sheets: Top load and top out

Fanfold: Rear in and top out

Copy Capability Original + 4 copies

Emulation ESC/P2, IBM 2390 Plus

Ribbon Type Cartridge; Monochrome

Ribbon Life 7 million characters (rolling Draft 10 CPI)

Input Data Buffer Up to 68KB

Windows Drivers

Windows Server 2000/2003/2008

Windows Vista

Windows XP

Windows 98

Windows 7

Interface

Parallel (Bi-directional IEEE-1284 nibble mode)

USB 2.0 (B type connector)

Serial RS-232C

Operation Panel Switches: 4 pcs

LED indicators: 4 pcs

Noise Level < 51 dBA in 10CPI draft ASCII (Conforming to ISO7779)

Ambient

Conditions

Temperature Operating: +5 to +40 °C.

Stand-by: -20 to +55 °C

Humidity Operating: 10 to 80%RH

(No condensation)

Stand-by: 5 to 85%RH

(No condensation)

Dimensions 359 mm (W) x 285 mm (D) x 159 mm (H)

Tally Dascom 1125

Weight 5 kg

Power Supply

Unit type: Switching mode power supply

Power cord: Detachable

Voltage rating: AC 230V (180V~264V), 50Hz to 60Hz

AC 110V/120V, 60Hz (factory option)

Stand by: Less than 3.8W

ESD: Comply with IEC801-2

Contact discharge: 4kV

Air discharge: 8kV

Power

consumption 28.2 W (standard ECMA-132)

MTTR < 20 minutes

MTBF 10000 hours @ 25% duty cycle

Certification CE, UL, FCC, ES, ISTA, RoHS, WEEE, REACH, ChemVerbotsV,

Microsoft Certified for Windows 7

Tally Dascom 1125

9 Interfaces

Parallel Interface

Parallel Interface Pin Assignment

Pin Signal Name Signal Tr a n s m i s s i o n

1 STROBE¯¯¯¯¯¯ Printer  Computer

2~9 DATA Printer  Computer

10 ACK¯¯¯ Printer  Computer

11 BUSY Printer  Computer

12 PE Printer  Computer

13 SELECT Printer  Computer

14 AFXT¯¯¯¯ Printer  Computer

15 Unused Unused

16 GND Printer  Computer

17 F-GND Printer  Computer

18 +5V Printer  Computer

19~30 GND Printer  Computer

31 INIT¯¯¯¯ Printer  Computer

32 FAULT¯¯¯¯¯ Printer  Computer

33 GND Printer  Computer

34 Unused Unused

35 FUSE Printer  Computer

36 SLCTIN¯¯¯¯¯¯ Printer  Computer

Parallel Interface Connector Diagram

Note: Any external devices connected to the parallel port should not draw current exceeding 200 mA from pin

18; otherwise it may affect the printer operation.

Tally Dascom 1125

USB Interface

The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at

12 Mbps. It uses the “B” type USB connector.

Serial Interface

Serial RS-232C Interface Pin Assignment

Pin Signal Symbol Signal Name Signal

Transmission

1 CG Chassis Ground —

2 TXD Send Data OUT

3 RXD Receive Data IN

4 RTS Request to Send OUT

7 SG Signal Ground —

20 DTR Data Terminal Ready OUT

25 +5V Power —

Serial RS-232 Connector Diagram

Tally Dascom 1125

10 Character sets & Code Pages

Character Sets

Standard Character Set 1

Standard Character Set 2

Tally Dascom 1125

IBM Character Set 1

IBM Character Set 2

Tally Dascom 1125

International character sets

International Character Set Commands

Country Command

USA ＜ESC＞“R”CHR＄（0）

France ＜ESC＞“R”CHR＄（1）

Germany ＜ESC＞“R”CHR＄（2）

UK ＜ESC＞“R”CHR＄（3）

Denmark1 ＜ESC＞“R”CHR＄（4）

Sweden ＜ESC＞“R”CHR＄（5）

Italy ＜ESC＞“R”CHR＄（6）

Spain1 ＜ESC＞“R”CHR＄（7）

Japan ＜ESC＞“R”CHR＄（8）

Norway ＜ESC＞“R”CHR＄（9）

Denmark2 ＜ESC＞“R”CHR＄（10）

Spain2 ＜ESC＞“R”CHR＄（11）

Lat America ＜ESC＞“R”CHR＄（12）

Korea ＜ESC＞“R”CHR＄（13）

Legal ＜ESC＞“R”CHR＄（64）

Tally Dascom 1125

Character Tables

Italic

Tally Dascom 1125

Graphic 1

Graphic 2

Tally Dascom 1125

Code Page Commands

Code Page ESC R Parameter

CRO-ASCII 3C

Arabic Farsi 96

Arabic Urdo 97

Greek DEC 46

Greek ELOT 928 6C

CP437 Latin US 80

CP737 Greek 93

CP850 Latin 1 82

CP851 Greek 88

CP852 Latin 2 87

CP857 Turkish 8D

CP858 (IBM with €) 9E

CP860 Portugal 84

CP861 Icelandic 94

CP863 French Canada 85

CP864 Arabic 8C

CP864 Arab. Extended 95

CP865 Nordic 86

CP866 Cyrillic 8E

CP866 Bulgaria 9D

Siemens Turkish 9B

DEC Turkish 9C

CP1250 Win Latin 2 70

CP1251 Win Cyrillic 71

CP1252 Win Latin 1 72

CP1253 Win Greek 73

CP1254 Win Turkish 74

8859-1 Latin 1 25

8859-1 Latin 1 (SAP) 2B

8859-2 Latin 2 26

8859-5 Cyrillic 2A

8859-7 Greek 2D

8859-9 Turkish 2E

8859-15 Latin 9 (Euro) 2F

BRASCII 6D

Abicomp 6E

Roman 8 4D

Tally Dascom 1125

Coax/Twinax(Hebrew) 4F

New-437 (Hebrew) 81

New-DIG 850 (Hebr.) 83

Old-Code 860 (Hebr.) 98

Flarro 863 (Hebrew) 99

Table 865 (Hebrew) 9A

CP775 Baltic A6

CP1257 Baltic 77

Mazovia (Poland) 92

Kamenicky (Czech) 91

CP866 Ukraine 8F

CP866 Kazakhstan 90

Tally Dascom 1125

Code Page Tables

CP 437 (US)

CP 737 Greek

Tally Dascom 1125

CP 850 (Multilingual)

CP 851

Tally Dascom 1125

CP 852 (Eastern Europe)

CP 857 (Turkish)

Tally Dascom 1125

CP 858

CP 860 (Portugal)

Tally Dascom 1125

CP 861 (Iceland)

CP 863 (French-Canadian)

Tally Dascom 1125

CP 864 Arabic

CP 864 Arabic Extended

Tally Dascom 1125

CP 865 (Norway)

CP 866 (Cyrillic)

Tally Dascom 1125

CP 866 Bulgaria

CP 1250 Win Latin 2

Tally Dascom 1125

CP 1251 Win Cyrillic

CP 1252 Win Latin 1

Tally Dascom 1125

CP 1253 Win Greek

CP 1254 Win Turkish

Tally Dascom 1125

8859-1 Latin 1

8859-1 Latin 1 (SAP)

Tally Dascom 1125

ISO 8859-2 (ISO Latin 2)

ISO 8859-5 Cyrillic

Tally Dascom 1125

ISO 8859-7 (Latin/Greek)

ISO 8859-9 (Turkish)

Tally Dascom 1125

ISO 8859-15 Euro (Code Page 923)

BRASCII

Tally Dascom 1125

Abicomp

Roman 8

Tally Dascom 1125

Coax/Twinax (Hebrew)

New-437 (Hebrew)

Tally Dascom 1125

New-Dig 850 (Hebrew)

Old-Code 860 (Hebrew)

Tally Dascom 1125

Flarro 863 (Hebrew)

865 Hebrew

Tally Dascom 1125

CP 1257

866 Ukraine

Tally Dascom 1125

866 Kazakhstan

Kamenicky

Tally Dascom 1125

Mazovia

CP 775

Tally Dascom 1125

CRO-ASCII

Arabic Farsi

Tally Dascom 1125

Arabic Urdo

Greek DEC

Tally Dascom 1125

Greek ELOT 928

Tally Dascom 1125

11 Control Codes Summary

Epson Emulation Command List

Command Sequence Function

BEL Beeper

BS Backspace

HT Tab horizontally

LF Line feed

VT Tab vertically

FF Form feed

CR Carriage return

SO Select double-width printing (one line)

SI Select condensed mode

DC1 Online

DC2 Cancel condensed mode

DC3 Offline

DC4 Cancel double-wide mode(one line)

CAN Cancel line

DEL Delete character

ESC SO Select double-width printing (one line)

ESC SI Select condensed mode

ESC SP n Set intercharacter space

ESC EM n NA

ESC ! n Print mode setup

ESC ( - n1 n2 m d1 d2 Choose character lineation

ESC $ n1 n2 Select absolute horizontal print position

ESC | n Set left margin

ESC % n Select user-defined set

ESC & Define user-defined set

ESC ( ^ n m d1 d2… Print data in character style

ESC (G NUL d Select graphics mode

ESC * m n1 n2… Select image mode

ESC . c v h m nL nH d1 d2… Print raster graphics

ESC + n Select n/360″line spacing

ESC – n Underline on/off

ESC / n Select vertical orientation channel

ESC ( C NUL n m Set page length

ESC ( c NUL nt mt nb mb Page setup

ESC ( U NUL n Set unit

ESC 0 Set 1/8″line spacing

ESC 2 Set 1/6″line spacing

ESC 3 n Set n/180″line spacing

ESC 4 Set Italic

ESC 5 Cancel Italic

ESC 6 Enable printable characters

ESC 7 Enable upper control characters

Tally Dascom 1125

ESC : Copy ROM to RAM

ESC ＜ Unidirectional mode(1 line)

ESC > Set MSB to 1

ESC = Set MSB to 0

ESC # Cancel MSB control

ESC ？n m Reassign graphics mode

ESC @ Initialize printer

ESC ＼n1 n2 Set relative horizontal print position

ESC A n Set n/60″line spacing

ESC B…NUL Set/cancel vertical tabs

ESC C n Set page length in lines

ESC D…NUL Set/cancel horizontal tabs

ESC E Select Bold

ESC F Cancel Bold

ESC G Select double-strike mode

ESC H Cancel double-strike mode

ESC J n Perform tactic n/180″line feed

ESC K n1 n2 … Select 8 pins single-density graphics

ESC L n1 n2 … Select 8 pins double–density graphics

ESC M Select ELITE（12CPI）

ESC N n Set bottom margin

ESC O Cancel bottom margin

ESC P Select PICA（10CPI）

ESC Q n Set right margin

ESC R n International character set

ESC S n Select superscript/subscript

ESC T Cancel superscript/subscript

ESC U n Select unidirectional/bidirectional printing mode

ESC ( V NUL n m Select absolute vertical print position

ESC W n Turn Double-wide mode on/off

ESC X n1 n2 Select font by pitch and point

ESC Y n1 n2 … Select 8 pins, high speed ,double –density graphics

ESC Z n1 n2 … Select 8 pins, high speed fourfold –density graphics

ESC a n Select justification

ESC b n Select vertical orientation channel

ESC c n m Set horizontal intercharacter space

ESC g Select 15CPI

ESC j n Perform reverse n/180″line feed

ESC k n Select typeface

ESC p n Turn proportional mode on/off

ESC q n Select character style

ESC r n Select printing colour

ESC t n Select character table

ESC (t nL nH d1 d2 d3 Assign character table

ESC ( v NUL n m Set relative vertical print position

ESC w n Turn double-high mode on/off

ESC x n Select print quality

ESC( B n1 n2 k m s v1 v2 c Barcode print

Tally Dascom 1125

IBM Emulation Command List

Command Sequence Function

BEL Beeper

BS Backspace

HT Tab horizontally

LF Line feed

VT Tab vertically

FF Form feed

CR Enter

SO Select double-wide mode

SI Select condensed mode

DC1 Online

DC2 Select 10CPI

DC3 Offline

DC4 Cancel double-wide mode(one line)

CAN Cancel buffer

ESC BEL Beeper

ESC BS Backspace

ESC HT Tab horizontally

ESC CR Enter

ESC LF Line feed

ESC SO Select double-wide mode

ESC SI Select condensed mode

ESC DC1 Online

ESC DC2 Select 10CPI

ESC DC3 Offline

ESC DC4 Cancel double-wide mode(one line)

ESC CAN Cancel buffer

ESC FF Form feed

ESC EM n Automatically Feed Paper mode

ESC : Set 12CPI

ESC VT Tab vertically

ESC 0 Select 1/8″line spacing

ESC 1 Select 7/72″line spacing

ESC 2 Select 1/6″line spacing or activate ESC A n command

ESC 3 n Select n/216″or 1/180″line spacing

ESC 4 Set top margin

ESC 5 n Automatic Line Feed

ESC 6 Select character set 2

ESC 7 Select character set 1

ESC = NA

ESC \ Print continuously from all character chart

ESC ^ Print single character from all character chart

ESC A n Select n/72″or n/60″line spacing

ESC B n Select Tab vertically

ESC C n Set page length in lines

Tally Dascom 1125

ESC C NUL n Set page length in inches

ESC D Select Tab horizontally

ESC E Select bold

ESC F Cancel bold

ESC G Select double-strike mode

ESC H Cancel double-strike mode

ESC I n Select printing mode

ESC J n Perform n/180″or n/216″single line feed

ESC K n1 n2 V1 V2 …Vn Normal density graphics

ESC L n1 n2 V1 V2 …Vn Dual-Density Bit Image Graphics (Half Speed)

ESC N n Select bottom margin

ESC O Cancel bottom margin

ESC P n Set proportional intercharacter

ESC Q n Offline

ESC R Clear tab

ESC S n Select superscript/subscript

ESC T Cancel superscript/subscript

ESC U n Select bidirectional printing on/off

ESC W n Select double-wide printing mode(continuous)

ESC X n m Set left and right margin

ESC Y n1 n2 V1 V2 …Vn Select double -density graphics

ESC Z n1 n2 V1 V2 …Vn Select fourfold -density graphics

ESC [- n1 n2 m1 m2 Select line

ESC [@ n1 n2 m1 m2 m3 m4 Select printing mode

ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc Select font and pitch

ESC [ K n1 n2 init id para1 para2 …paran Set initialization condition

ESC [ T n1 n2 n3 n4 Hc Lc Set code page

ESC [\ Set vertical unit

ESC [d Select printing quality

ESC [f n1 n2 k m s v1 v2c Set barcode parameters

ESC [g n1 n2 m Select high-density graphics printing

ESC [p n1 n2 Set barcode data

ESC ] Feed paper in reverse direction

ESC_ n Print upper-line

ESC- n Print underline

ESC d n m Move the current printing position

ESC j Stop printing

ESC r n Select printing colour

ESC * m Select graphic mode

If you need more details regarding the emulation commands, please contact us.

Tally Dascom 1125

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

a. This device may not cause harmful interference.

b. This device must accept any interference received, including interference that may cause undesired

operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

 Re-orientate or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/TV technician for help.

DASCOM REPRESENTATIVES

GERMANY

DASCOM Europe GmbH

Heuweg 3

D-89079 Ulm

Deutschland

Tel.: +49 (0) 731 2075 0

Fax: +49 (0) 731 2075 100

www.dascom.com

UNITED KINGDOM

DASCOM GB Ltd

ViewPoint, Basing View,

Basingstoke, Hampshire

RG21 4RG, England

Phone: +44 (0) 1256 481481

Fax: +44 (0) 1256 481400

www.dascom.com

RUSSIA and CIS

DASCOM Europe GmbH

Representation Moscow

Leninsky Prospekt 95a, Office 322

119313 Moscow, Russian Federation

Phone: +7 (495) 984 70 65

Fax: +7 (495) 984 56 42

www.dascom.com

SINGAPORE (ASIA PACIFIC)

DASCOM AP Pte Ltd

63 Hillview Avenue

#08-22, Lam Soon Industrial Building

Singapore 669569

Phone: +65 6760 8833

Fax: +65 6760 1066

www.dascom.com.sg

AMERICAS

DASCOM Americas Corporation

421 W. Main Street, Waynesboro,

VA 22980, USA

Phone:+1 (877) 434 13 77

www.dascom.com

FRANCE

DASCOM Europe GmbH

117 Avenue Victor Hugo

92100 Boulogne-Billancourt

France

Phone: +33 (1) 73 02 51 98

www.dascom.com

CEE

DASCOM Europe GmbH

Europaring F15 301

2345 Brunn a. G.

Austria

Phone: +43 (1) 236 01 70 10

www.dascom.com

or in any different form requires our explicit approval. We reserve the right to make changes to this manual

without notice. All care has been taken to ensure accuracy of information contained in this manual. However,

we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information

herein.”

Dascom Printer TD11250 Dot Matrix Printer User Manual 1125 UG 2011 06 22

Dascom Printer (Jiangmen) Co.,Ltd. Dot Matrix Printer 1125 UG 2011 06 22

Users Manual

Navigation menu

Namespaces

Views

Navigation