Dascom Printer TD13250 Dot Matrix Printer User Manual 1325 UG 2011 07 03

Dascom Printer (Jiangmen) Co.,Ltd. Dot Matrix Printer 1325 UG 2011 07 03

Users Manual

Download: Dascom Printer TD13250 Dot Matrix Printer User Manual 1325 UG 2011 07 03
Mirror Download [FCC.gov]Dascom Printer TD13250 Dot Matrix Printer User Manual 1325 UG 2011 07 03
Document ID1520566
Application IDaG44N38vCMzS2QMtRrTYbg==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize386.6kB (4832555 bits)
Date Submitted2011-08-10 00:00:00
Date Available2011-08-10 00:00:00
Creation Date2011-07-03 22:14:57
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2011-07-03 22:14:57
Document TitleMicrosoft Word - 1325 UG 2011-07-03.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: DYAPP

Tally Dascom 1325
Important Safety Instructions (English)
Read the following instructions thoroughly before starting up your printer.
•
Never carry out maintenance or repair work yourself. Always contact a qualified service technician.
•
Keep this Operator’s Manual in a place which is easily accessible at all times.
•
Place the printer on a solid and even base so that it cannot fall.
•
Never place the printer in the vicinity of inflammable gas or explosive substances.
•
Ensure the printer is connected to a socket with the correct mains voltage.
•
Always disconnect the printer from the mains before opening the device to perform maintenance work or
remedy errors.
•
Do not expose the printer to high temperatures, direct sunlight or dust.
•
Keep all liquids away from the printer.
•
Protect the printer from shock, impact and vibration.
•
Make sure that the printer and computer are switched off before connecting the data cable.
•
The print head will become very hot during printing; avoid contact with the print head after printing has
finished.
•
Do not perform any operation or action in any way other than those provided in this manual. When in
doubt, contact your dealer or your customer support.
Tally Dascom 1325
Wichtige Sicherheitshinweise (German)
Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen.

Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie
immer einen qualifizierten Servicetechniker.

Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.

Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.

Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven
Stoffen auf.

Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen.

Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den
Netzstecker an der Steckdose ziehen.

Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.

Keine Flüssigkeiten mit dem Drucker in Berührung bringen.

Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen.

Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel
angeschlossen wird.

Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen
lassen.

Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab.
Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.
II
Tally Dascom 1325
Consignes importantes de sécurité (French)
Lire attentivement les instructions suivantes avant de mettre l’imprimante en service.

Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un
dépanneur qualifié.

Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.

Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de
substances explosives.

Ne connecter l’imprimante à une prise que lorsque la tension est correcte.

Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et
toujours débrancher le connecteur secteur de la prise murale.

Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la
poussière.

Ne pas mettre l’imprimante en contact avec des liquides.

Ne pas exposer l’imprimante à des chocs, impacts ou vibrations.

S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de données.

La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques
instants avant d’y toucher.

N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel. En
cas de doute, veuillez contacter votre distributeur ou service après-vente.
III
Tally Dascom 1325
Indicazioni di sicurezza importanti (Italian)
Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni.
Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di
assistenza qualificato.

Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.

Collocare la stampante su una superficie stabile, per evitare che cada a terra.

Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive.

Collegare la stampante a una presa di corrente con tensione adeguata.

Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il
connettore di rete dalla presa.

Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere.

Evitare il contatto della stampante con liquidi.

Non esporre la stampante a colpi, scosse o vibrazioni.

Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati.

Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno
quindi lasciarla raffreddare qualche istante.

Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In
caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.
IV
Tally Dascom 1325
Instrucciones de seguridad importantes (Spanish)
Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio.
Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio
calificado.

Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.

Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.

Nunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias explosivas.

Asegure conectar la impresora sólo a un enchufe con un voltaje correcto.

Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de
alimentación del enchufe.

No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.

No ponga la impresora en contacto con fluidos.

Nunca exponga la impresora a sacudidas, choques o vibraciones.

Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos.

La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo algún
tiempo antes de tocarla.

No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala en
el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio post-venta.
Tally Dascom 1325
Правила по технике безопасности. (Russian)
Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера.

Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о
неисправностях квалифицированным сервисным техникам.

Данная инструкция должна быть всегда доступна каждому пользователю.

Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.

Ни в коем случае не ставьте принтер вблизи легко воспламеняющихся газов и взрывчатых
веществ.

Включайте принтер в розетку только с соответствующим напряжением.

Если Вы хотите отключить принтер от напряжения, сначала выключите принтер сам и затем
выньте штекер из розетки.

Берегите принтер от нагревания, от попадания на него прямых солнечных лучей и пыли.

Не допускайте попадания жидкости на принтер.

Нельзя подвергать принтер тряске, ударам и вибрации.

Убедитесь, что принтер и компьютер выключены, только после этого соедините принтер с
компьютером.

Печатающая головка нагревается во время работы принтера. Поэтому подождите какое-то
время, прежде чем дотронуться до нее.

Пользуйтесь принтером так, как это написано в документации. Если у Вас возникают неясности,
обращайтесь с вопросами к Вашим продавцам или в сервисный центр.
VI
Tally Dascom 1325
Instruções Importantes sobre Segurança (Portuguese)
Leia as instruções de segurança antes de usar a impressora.

Consulte sempre um técnico qualificado para executar uma reparação .

Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas.

Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias
explosivas.

Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.

Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.

Não exponha a impressora a temperaturas altas ou luz solar direta.

Não aproxime substâncias líquidas da impressora.

Proteja a impressora de choques, impactos e vibrações.

Desligue a impressora e o computador antes de conectar o cabo da rede.

A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de tocá-la.

Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida,
contate seu revendedor ou companhia de serviço.
VII
Tally Dascom 1325
Önemli Güvenlik Talimatları (Turkish)
Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun.

Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiye bir
uzman servis-teknisyenine haber verin.

Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.

Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren nesnelerin
yakınına koymayın.

Yazıcı akım kablosunu sadece doğru gerilime sahip bir prize takın.

Yazıcıyı şebeke ağından ayırmak istediğinizde, yazıcıyı kapatın ve ağ-fişini her zaman prizden çıkartın.

Yazıcıyı ne yüksek ısılı ne de doğrudan güneş ışığına ve toza mâruz kalan mekânlarda bulundurun.

Yazıcı hiçbir sıvı maddeyle temasta olmamalıdır.

Yazıcı hiçbir sarsıntıya, darbeye veya titreşime mâruz kalmamalıdır.

Veri kablosu bağlanmadan önce hem yazıcının hem de bilgisayarın kapalı olduklarından emin
olmalısınız.

Yazıcının başı basma esnasında yüksek ısıya ulaşıyor. Bu yüzden lütfen dokunmadan önce kısa süre
soğumasını bekleyin.

Yazıcının işletimi ve kullanımında bu dokümantasyondaki talimatların hiç dışına çıkmayın. Sorunlu
görünen hususlarda lütfen imâlatçınıza veya müşteri hizmetleri servisinize başvurun.
VIII
Tally Dascom 1325
TRADEMARK ACKNOWLEDGEMENTS
“IBM” is a trademark of International Business Machines Corporation.
“EPSON” is a trademark of Epson America Incorporated.
“DEC” is a trademark of Digital Equipment Corporation.
“Centronics” is a trademark of Centronics Data Computer Corporation.
“DOS” is a trademark of Microsoft Corporation.
“SAP” is a trademark of SAP AG.
“Windows”, “Windows 7”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows
2003/2008 Server”, “Windows XP” and “Windows Vista” are trademarks of Microsoft Corporation.
All other product names and company names appearing in this manual are the registered trademarks or
trademarks of the individual companies.
IX
Tally Dascom 1325
Tally Dascom 1325
TABLE OF CONTENTS
1 UNPACKING GUIDE ........................................................................................................................................ 1
PLACING THE PRINTER .......................................................................................................................................... 2
PRINTER COMPONENTS ........................................................................................................................................ 2
2 SETTING UP PRINTER .................................................................................................................................... 4
INSTALL RIBBON .................................................................................................................................................. 4
INSTALL THE PAPER LOADER.................................................................................................................................. 5
CONNECTING THE INTERFACE CABLE ...................................................................................................................... 5
CONNECTING THE MAINS POWER .......................................................................................................................... 6
INSTALLING THE WINDOWS DRIVER ........................................................................................................................ 7
3 PAPER INSTALLATION GUIDE ..................................................................................................................... 10
ADJUSTING THE PRINT GAP LEVER ....................................................................................................................... 10
FRICTION FEED HANDLING.................................................................................................................................. 11
TRACTOR FEED HANDLING .................................................................................................................................. 11
4 CONTROL PANEL OPERATION .................................................................................................................... 12
PANEL OPERATION ............................................................................................................................................. 14
Online State ............................................................................................................................................................ 15
Offline State ............................................................................................................................................................ 16
Power-On State ...................................................................................................................................................... 17
LANGUAGE SETUP .............................................................................................................................................. 18
SLIP SETUP ....................................................................................................................................................... 19
5. PRINTER SETTING CHANGES .................................................................................................................... 20
SYSTEM SETUP .................................................................................................................................................. 20
PRINT SETUP ..................................................................................................................................................... 20
PAGE SETUP ...................................................................................................................................................... 22
INTERFACE SETUP .............................................................................................................................................. 23
ADVANCED SETUP.............................................................................................................................................. 23
VERTICAL ALIGNMENT ........................................................................................................................................ 33
CHANGE PIN FUNCTION...................................................................................................................................... 34
ADJUST PHYSICAL MARGINS ............................................................................................................................... 35
DASCOM PRINTER SETUP TOOL ........................................................................................................................... 37
6 MAINTENANCE ............................................................................................................................................. 38
CLEANING AND VACUUMING THE PRINTER ............................................................................................................. 38
CLEANING THE PAPER ROLLERS ........................................................................................................................... 38
7 TROUBLESHOOTING .................................................................................................................................... 40
PRINT QUALITY PROBLEMS AND SOLUTIONS ........................................................................................................ 40
PAPER HANDLING PROBLEMS AND SOLUTIONS ..................................................................................................... 41
OPERATING PROBLEMS AND SOLUTIONS .............................................................................................................. 41
XI
Tally Dascom 1325
ERROR INDICATIONS ON LEDS ............................................................................................................................ 42
DIAGNOSTIC FUNCTIONS .................................................................................................................................... 43
FIRMWARE UPDATE ........................................................................................................................................... 44
8 GENERAL SPECIFICATIONS ......................................................................................................................... 45
9 INTERFACES .................................................................................................................................................. 50
PARALLEL INTERFACE ......................................................................................................................................... 50
USB INTERFACE ................................................................................................................................................ 50
10 CHARACTER SETS & CODE PAGES .......................................................................................................... 51
CHARACTER SETS .............................................................................................................................................. 51
INTERNATIONAL CHARACTER SETS ........................................................................................................................ 53
INTERNATIONAL CHARACTER SET COMMANDS ...................................................................................................... 53
CHARACTER TABLES ........................................................................................................................................... 54
CODE PAGE COMMANDS .................................................................................................................................... 56
CODE PAGE TABLES ........................................................................................................................................... 58
11 CONTROL CODES SUMMARY ................................................................................................................... 82
EPSON EMULATION COMMAND LIST.................................................................................................................... 82
IBM EMULATION COMMAND LIST ....................................................................................................................... 84
FCC STATEMENT ............................................................................................................................................. 86
XII
Tally Dascom 1325
1 Unpacking Guide

Place your packaged printer on a solid base.

Make sure that the “Up” symbols point in the correct direction.

Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging
material.

Check the printer for any visible transport damage and missing items. If you find any transport
damage or if any accessories are missing, please contact your dealer. The following items should be
included:
Printer
Paper feed knob
Paper feed tray
Power cord
Ribbon cartridge
CD-ROM
Installation Guide
Remove the packaging materials from the printer as follows:
1. Remove all the visible tapes on the front cover and the tractor.
2. Open the front cover of the printer.
3. Remove the shipping cardboard from around the print head.
4. Install the paper feed knob.
Tally Dascom 1325
Placing the Printer
Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it
cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that
there is enough space for sufficient ventilation and for the printed output.
When selecting the printer location, observe the following additional instructions:

Never place the printer near to any flammable gas or explosive substances.

Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect
it from the sunlight with a curtain.

When connecting a computer to the printer, make sure the maximum recommended cable length is not
exceeded.

Ensure sufficient distance between the printer and any heating devices/radiators.

Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty
environments.

It is recommended the printer is installed in a position which reduces noise exposure to the work place
during printing.
Printer Components
Tally Dascom 1325
Component
Gap Lever
Function
Controls printing impact or density.
Adjusts the print gap lever according to the thickness of paper.
Paper Guides
Adjust positioning of single sheet paper.
Paper Loader
For single sheet.
Paper Holder
For single sheet in larger sizes.
Paper Slot
For friction feed (forward).
Print Head
24-pin printing mechanism
Cover
Control Panel
Protects print head and other components inside, and reduce noise.
Shows printer status, for printer setup.
Paper Feed Lever
Two positions:
Paper Feed Knob
Manual feed or vertical positioning of paper
Power Switch
Power printer ON or OFF
Ribbon Cartridge
Install ribbon in the printer.
Ribbon Frame
For guiding ribbon installation on print head.
Tractors
For feeding and adjustment of continuous forms.
Power Receptacle
Connects power cord to the printer.
Interface
Connects interface cable from the host.
= continuous forms;
= single sheet paper
Tally Dascom 1325
2 Setting Up Printer
Install Ribbon
1. Ensure the power to the printer is off and the print gap lever “A” is set to the furthest open position. Move
the carriage to the centre of the print platen.
2. Install the recess positions  and ② on the ribbon cassette into the printer mounting.
3. Press the ribbon frame  onto the print head.
4. Turn the ribbon knob ④ in clockwise direction until the ribbon fabric is taut. Move the carriage left and
right to ensure the carriage and ribbon fabric can move smoothly.
5. Ensure the print gap lever “A” is set to the original position.
6. Close the printer’s front cover. When printer is in operation, ensure the printer’s front cover is closed to
keep the noise level to a minimum.
Notes on Ribbon Cartridge Removal:
1.
2.
3.
4.
5.
Eject any paper loaded in the printer.
Turn off the printer power.
Set the gap lever to the most open position labeled “RIBBON”.
Open the front cover.
Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed,
as the print head may be hot.
6. Remove the blue ribbon frame from the print head.
7. Use fingers to take hold of the handle on the ribbon cartridge firmly, and pull the cartridge towards you to
unlatch it. Some force may be needed to unlatch the cartridge.
8. Remove the ribbon fabric from the print head carefully without entangling it.
Tally Dascom 1325
Install the Paper Loader
As shown in the picture below, ensure the sheet feeder fingers fit into the slots in front of the printer. Push in
the sheet feeder until its sides latch on the fixed bolts in the printer. The sheet feeder is now installed
successfully.
To remove the sheet feeder, use one hand to hold the printer and the other hand to pull and unlatch the sheet
feeder.
Connecting the Interface Cable
The 36-pin Centronics parallel and USB ports are located at the rear of the printer. IMPORTANT: Make sure
the printer and the computer are switched off before connecting or disconnecting the interface cable to
prevent electrical damage to the interface ports.
Tally Dascom 1325
Connecting the Mains Power
Checking the printer voltage
Make sure that the device has been set according to your country’s power supply voltage. To do this, check
the rating plate at the back of the printer. Contact your dealer if the setting is incorrect.
Never switch on the printer if the voltage setting is incorrect; this may result in electrical
damage to the printer.
Make sure that the power switch
‘‘A’’, located to the right side of
the
printer,
is
in
the
OFF
position.
Connect the power cord to the
power inlet of the printer.
Connect the power cord plug to
a mains socket. Switch on the
printer.
Tally Dascom 1325
Installing the Windows Driver
(Windows 2000/2003/2008 Server/XP/Vista/7)
1. Your printer CDROM comes with
Windows drivers. Go to the Drivers
folder
and
run
the
Installer
“DriverSetup.exe”. You will see the
screen on the right. Click “Next” to
continue.
2. A list of ports available on your
system will be displayed as shown
on the right. Choose the desired
port
to
use.
Click
“Next”
to
continue.
3. Select the desired printer model as
shown on the right. Click “Next” to
continue.
Tally Dascom 1325
4. Here you can choose whether to
set the driver as the system
default driver, and whether you
want to print the Test Page after
installation is completed. If the
driver had been installed before,
it would be listed in the white
box on the right. Select the listed
driver (if any) if you want to
replace it; otherwise a copy of
the driver will be installed. Click
“Next” to continue.
5. Click
“Finish”
to
start
the
installation process.
6. If the driver is not yet Microsoft
Certified, the message on the right
would
appear. Click
Anyway”. (As
we
“Continue
continue
to
expand our product portfolio, not
all of our drivers may be certified
yet. Please check our website
www.dascom.com for the latest
certified drivers.)
Tally Dascom 1325
7. Installation in progress.
8. After
installation
is
completed
successfully, you will see the
message on the right.
Tally Dascom 1325
3 Paper Installation Guide
The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include
envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into
the printer using the forms tractors. The printer is able to print 1~7 plies multipart paper.
Do not load paper that has been folded or is damaged, wrinkled, or curled.
Adjusting the Print Gap Lever
The print gap lever is on the right side of the printer. Take care to adjust the print gap lever to a suitable
position whenever you change the number of copies being printed. Using the wrong print gap may cause
print head damage or paper jams.
Print Gap Lever
Paper type
Weight (g/m2) / ply
Thickness (mm)
Single sheet
52~100
0.06~0.12
2-ply
40~52
0.12~0.14
3-ply
40~52
0.17~0.22
4-ply
40~52
0.23~0.27
5-ply
40~52
0.28~0.33
6-ply
40~52
0.34~0.38
7-ply
40~52
0.39~0.45
7P
7-ply above
40~52
0.45~0.58
Change ribbon
10
Gap lever position
1P~2P
3P~4P
5P~6P
Tally Dascom 1325
There are 2 paper feed modes: friction feed and tractor feed.
Friction Feed Handling
1. Move the paper-feed lever forward to “
” for friction feed mode.
2. Adjust the print gap lever if necessary.
3. Align the left paper guide with the mark on the left of the single sheet feeder. Adjust the right paper guide
to the width of the paper used.
4. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with the platen.
5. The paper should advance automatically to the print position. The printer is now ready to print in the online
state.
Paper Feed Lever
Paper Guides
Tractor Feed Handling
1. Move the paper-feed lever backward to “
” for continuous paper position.
2. Adjust the print gap lever if necessary.
3. Raise the tractor doors and fit the first 3 paper holes onto the left tractor pins. Close the left tractor door. In
the same way, install the paper on the right tractor.
4. Adjust the right tractor to the width of the paper until the paper is flat. Do not stretch the paper too taut.
Push the right lock lever down to secure the right tractor in place.
5. Press the【Load/Eject】key to load the paper to the starting print position. The printer is now ready to print
in the online state.
11
Tally Dascom 1325
4 Control Panel Operation
There are 4 switches S1~S4 and 4 LEDs L1~L4. The meaning and application of each switch and LED are
described below.
LED Indicators
“Power/Paper Out” LED:
On: Power on
Flashing: Paper out
Flashing + buzzer: Paper jam
“Online” LED:
On: The printer is in online state and ready to receive data from the computer.
Off: The printer is in offline state and cannot receive data.
“Front Exit” LED:
On: After printing, single sheet paper exits at the front.
Off: After printing, single sheet paper exits at the rear.
“Slip” LED:
On: Slip paper profile is selected.
Off: Slip paper profile is not selected.
(Note: “Slip” refers to a small paper form.)
12
Tally Dascom 1325
Control Panel Keys
“Online” Key:
This key switches the printer between online and offline states. Printing is stopped when the printer is
switched to offline state. When printer is switched to online state again, printing will resume.
“Load/Eject” Key:
When paper is loaded, pressing this key will eject the paper (single sheet mode) or park the paper
(continuous paper mode). When paper is not loaded, pressing this key will load the paper to the starting
print position.
“LF/FF” Key:
Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a
few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode).
“Tear Off” Key:
When online, this key will move any loaded continuous paper to the tear-off position. When offline, this
key is used to select the Slip paper profile.
Table 4.1
Switch
Top Label
Bottom Label
S1
Tear Off
Slip
S2
LF/FF
Exit Dir
S3
Load/Eject
S4
Online
Table 4.2
LED
Function
L1
Power/Paper Out
L2
Slip
L3
Front exit
L4
Online
13
Tally Dascom 1325
Panel Operation
There are 3 states of operation: Online, Offline and Power On.
In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed,
Load/Eject, and switch to Offline state.
In the Offline state, the keys provide the following functions: Select Slip paper profile, select paper exit
direction, Load/Eject, switch to Online state, micro feed, clear buffer and restore factory defaults.
To enter the Power On state, the user holds down a key or a combination of keys while powering up the
printer. This state provides the following functions: Configure Slip paper profile, Main Menu setup, Hex-dump,
print Main Menu, access Service Menu, adjust page margins, restore factory defaults, and firmware update.
The followings describe the 3 states in details.
Legend:
[A] = press and hold switch A
{B} = press and then release switch B
[A]+ {B} = press switch B while holding A
14
Tally Dascom 1325
Online State
Function Name
Switch
Operation
LED
Function Description
This is valid for tractor mode only. It feeds the form to the
tear-off position. After tearing off the form, printing starts
Tear Off
{S1}
on the next TOF by:
 pressing S1 once, or
 receiving print data from the host.
LF
{S2}
Feeds a line with every press of S2.
By holding S2, the printer initially feeds a few lines; then
FF
[S2]
feeds the form to the next TOF for rear tractor or ejects
the form for cut sheets.
 Load: Automatically loads the paper (according to path
selection) when no paper is on the platen.
Load/Eject
{S3}
 Eject: For rear tractor, it retracts the form from the
platen to allow users to install cut sheets. (NOTE:
Users have to toggle the path selection lever.)
For cut sheets, it ejects the form on the platen.
Online
{S4}
L4
Toggles between Online and Offline states.
15
Tally Dascom 1325
Offline State
Function Name
Slip
Switch
Operation
[S1]
LED
Function Description
L2
 Press and hold this key until printer beeps twice to activate
the Slip profile mode. L2 will turn on.
 Press and hold this key until printer beeps twice to exit the
Slip profile mode. L2 will turn off.
Exit Dir
{S2}
L3
This is valid for single sheet mode only. It controls the exit
direction of the friction sheet paper.
 Load: Automatically loads the paper (according to path
selection) when no paper is on the platen.
Load/Eject
{S3}
 Eject: For rear tractor, it retracts the form from the platen to
allow users to install cut sheets. (NOTE: Users have to
toggle the path selection lever.)
For cut sheets, it ejects the form on the platen.
Online
{S4}
L4
Micro Forward
{S3}+[S4]
While holding down S4, press S3 to micro feed paper up.
Micro Reverse
{S2}+[S4]
While holding down S4, press S2 to micro feed paper down.
Clear Buffer and
{S1}+[S4]
 Clears the print buffer. Beeps once upon completion.
Reset
Toggles between Online and Offline states
 Pressing S1 longer initializes the printer to default settings.
Beeps 3 times upon completion.
16
Tally Dascom 1325
Power-On State
Function
Switch
Name
Operation
Menu Setup /
EDS
Slip Setup
LED
[S1]
Function Description
Allows for Main Menu setting changes. Please read the
instructions printed on how to change settings when this
mode is activated. (EDS: Electronic DIP Switch)
[S2]
Configures the Slip paper profile such as top and left
margins. Refer to Slip Setup section below for details.
Beeps once to indicate going into hex dump mode:
 Prints data from host in hexadecimal representation.
 Pressing S4 suspends the printing.
Hex Dump
[S3]
 When the hex dump has finished, pressing S4 forces the
printing of the last line of data, as any line termination
control code from host has no function.
 Switch off the power to terminate the hex dump.
17
Tally Dascom 1325
Self Test /
[S4]
Status Page
Service Menu
Adjust Page
Margins
Restore Factory
Defaults
[S1]+[S2]
Prints the printer settings and self-test pattern.
Vertical Alignment, Change Pin Function and Endless Self
Test
[S3]+[S4]
Includes Adjust Fanfold Top Margin, Adjust Single Top
Margin, Adjust Fanfold Left Margin, Adjust Single Left
Margin and Adjust Tear-Off position.
[S2]+[S3]+[S4]
Restore settings to factory defaults except for Change Pin,
Vertical Alignment and Adjust Page Margin Parameters.
L1, L4
 Alternate flashing of L1 and L4 indicates ready for
firmware update from host.
Firmware
[S1]+[S2]+[S3]+
Update
[S4]
 When new firmware is being received: L1 and L4 flash
together, followed by L1 and L3 flash together.
 When downloading is completed, the carriage returns to
home position. Printer initializes normally.
 Allows user to select one of the following languages:
Language
Setup
[S2]+[S3]
English, German, Russian, Italian, French, Spanish and
Turkish. Factory default is English. Refer to Language
Setup section below for details.
Language Setup
The panel menu can display the following languages: English, German, Russian, Italian, French, Spanish and
Turkish. Factory default setting is English. To change it to another language, hold down the [LF/FF] and
[Load/Eject] keys on the panel and power-on. Upon exiting the Language Setup Menu, a listing of the current
configuration is printed, and this is followed by Main Menu Setup.
Below is an example of changing from English to German language:
18
Tally Dascom 1325
Slip Setup
Slip media refers customized forms specific to each application. Each slip may have its own unique top margin
or left margin. This is called the slip profile. The Slip setting provides a convenient way to set the printer top
and left margin settings to the slip profile at the press of a panel key without the need to manually change the
top and left margins, whenever you want to do your slip printing. Likewise, should you decide to print on
standard paper forms, you can exit from the slip profile easily at the press of a panel key.
To configure the slip top and left margin parameters, please do the followings:
1. Power up printer while pressing 【LF / FF】 key until the print head starts moving, then let go.
2. Load paper. The printer prints the few lines below.
Slip Setup
【LF / FF】 = OK 【Tear Off】 = Back 【Load / Eject】 = Next 【Online】 = Exit
Current Setting: Fanfold Top Margin
3. Press the 【Load / Eject】 key to scroll to the item you want to change. The available items are Fanfold Top
Margin, Fanfold Left Margin, Single Top Margin and Single Left Margin. To select the item, press 【LF / FF】
key. In the above example, the printer will print out:
Fanfold Top Margin
【LF / FF】 Press: PrevSetup
Fanfold Top Margin 0mm
4. Press the 【Load / Eject】 key to increase by 1 mm, or press the 【Tear Off】 key to reduce 1 mm. The
range is 0~65 mm.
5. Press the 【LF / FF】 key to confirm the current selection. To save selection into memory, press the 【LF
/ FF】 key. If you do not want to save, use the 【Load / Eject】 key to scroll to “No” before pressing the
【LF / FF】 key to confirm.
6. Press the 【Online】 key to exit from Slip Setup.
19
Tally Dascom 1325
5. Printer Setting Changes
In order to meet individual print requirements, the printer configurations may be changed as follows: Hold
down the Tear Off key while powering on the printer, release the Tear Off key when the print head starts to
move. The printer will enter Main Menu setup state. Follow the instructions printed on how to make setting
changes. When a new setting is saved, it is retained after the printer has been powered off.
The Main Menu is grouped into 5 sub-menus: System Setup, Page Setup, Print Setup, Interface Setup and
Advanced Setup. A detailed description of the sub-menus is given below. The settings in bold and italic refer
to the default settings.
System Setup
System
Setup
Emulation
Auto CR
(IBM)
Auto LF
Valid Settings
Function
ESC/P2, IBM 2390
Selects the printer emulation. This should be the same as the host
Plus
printer driver.
Yes, No
Yes, No
Yes: LF = LF+CR; No: LF = LF
(Applies to IBM emulation only)
Yes: CR = CR+LF; No: CR = CR
Auto: Text & graphics in bi-direction; double height in uni-direction.
Print Dir
Bi-Dir, Uni-Dir,
Uni-Dir: Prints everything in uni-direction. Bi-dir: Prints everything in
Auto
bi-direction. Note: Top position print direction may be affected by Top
Print Dir setting.
Top Print
Dir
Bi-Dir, Uni-Dir
Bi-dir: Prints top position according to Print Dir setting. Uni-dir: Prints
top position in uni-direction regardless of Print Dir setting.
Impact
Normal, Heavy
Heavy: Higher impact force for multipart printing
IBM AGM
Yes, No
Selects the IBM graphic mode. Applies to IBM emulation only
Print Setup
Print Setup
Font
Valid Settings
Draft, Roman, Sans Serif, Courier, Prestige, Script,
OCR-B, OCR-A, ORATOR, GOTHIC, SOUVENIR
Pitch
10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS
Zero
0,Ø
HS-Draft
On, Off
Function
Selects the font.
Controls the characters per
inch setting.
Selects slashed or no-slash
zero.
On: Prints High Speed Draft
when Draft font is selected.
20
Tally Dascom 1325
When printing 180x180 DPI
Graphic
Speed
graphics: Normal – prints in
Normal, Fast, Ultra
180x180 DPI, Fast – prints in
90x180 DPI, Ultra – prints in
60x180 DPI.
IBM Set 1/2
Selects the IBM character
Set 1, Set 2
set. 1: Normal; 2: Extended
USA, France, Germany, UK, Denmark, Sweden, Italy,
Int'l Char Set
Spain, Japan, Norway, Denmark II, Spain II, Latin AM,
Korea, Legal
14+1 international character
set selections
1. CP 437
2. CP 737
3. CP 850
4. CP 851
5. CP 852
6. CP 857
7. CP 858
8. CP 860
9. CP 861
10. CP 863
11. CP 864
12. CP 864 Extended
13. CP 865
14. CP 866 Cyrillic
15. CP 866 Bulgaria
Code Page
16. CP 1250
National code page
17. CP 1251
selections
18. CP 1252
19. CP 1253
20. CP 1254
21. 8859-1
22. 8859-1 (SAP)
23. 8859-2
24. 8859-5
25. 8859-7
26. 8859-9
27. 8859-15
28. BRASCII
29. Abicomp
30. Roman8
31. Coax/Twinax
32. New-437
21
Tally Dascom 1325
33. New-Dig 850
34. Old-Code 860
35. Flarro 863
36. 865 Hebrew
37. CP 1257
38. 866 Ukraine
39. 866 Kazakhstan
40. Kamenicky
41. Mazovia
42. CP 775
43. CRO-ASCII
44. Arabic Farsi
45. Arabic Urdo
46. Greek DEC
47. Greek ELOT 928
Character
Table
Character table type
Graphic Table, Italic Table
selection
Page Setup
Page Setup
Line Per Inch
Fanfold Form Length
Fanfold Top Margin
Fanfold Bottom
Margin
Single Form Length
Single Top Margin
Single Bottom
Margin
Perforation Skip
Valid Settings
Function
1, 2, 3, 4, 5, 6, 7, 8
Sets the line spacing
3",3.5",11/3", 4", 5", 5.5" 6",7",8",
8.5",11", 70/6", 12", 14", 17"
Sets the page length for tractor mode
Sets the top margin for tractor mode. Due to
0/60" … 10/60"…99/60"
mechanical tolerance, 0/60” is not guaranteed.
Sets the bottom margin for tractor mode. Due
0/60"…10/60"...30/60"
to mechanical tolerance, 0/60” is not
guaranteed.
3", 3.5", 11/3", 4", 5", 5.5", 6", 7",
8", 8.5", 11", 70/6", 12", 14", 17"
Sets the page length for friction mode
Sets the top margin for friction mode. Due to
0/60" … 10/60"…99/60"
mechanical tolerance, 0/60” is not guaranteed.
Sets the bottom margin for friction mode. Due
0/60"…10/60"...30/60"
to mechanical tolerance, 0/60” is not
guaranteed.
Yes, No
Skips printing on perforation area
Specifies the waiting time before feeding the
page to tear-off position automatically. Manual:
Auto Tear
Manual, 0.5s, 1s, 2s, 3s, 4s, 5s
Auto tear mode is off. View1s, View2s, View3s:
View1s, View2s, View3s
After printing is completed, the printer will feed
the paper until the last printed line is at the
tear-off position. (Applies to tractor mode only)
22
Tally Dascom 1325
Exit Direction
Front, Rear
Slip
Off, On
Selects eject direction for friction loaded
papers.
Selects the Slip profile mode.
Interface Setup
Interface
Valid Settings
Setup
Function
For multi-host connection. Auto: First come first served;
Interface
Auto, Parallel, USB
Parallel/USB: Serves the designated host only.
I-PRIME
Yes, No
Yes: Host I-Prime signal resets the printer.
Auto IF
Delay
Determines the waiting time before receiving data from another
10s, 30s
interface.
User Font: Part of RAM is used for user download characters;
Buffer: Disables user character download function; uses RAM for
RAM Usage
User Font, Buffer
expanded buffer size up to 92KB.
Yes: Sets the parallel interface of the printer to bidirectional
mode (IEEE 1284, Nibble mode), e.g. for Windows Plug & Play.
No: Sets the interface to compatibility mode in order to ensure
CX Bid
Yes, No
reliable operation with special external boxes.
Advanced Setup
Advanced Setup
Valid Settings
Function
Specifies the waiting time before loading a cut
Auto Load
Manual, 0.5s, 1s, 1.5s, 2s
sheet automatically. Manual: Auto load mode is
off. (Applies to friction mode only)
Paper Jam
Prevention
Flattens paper edges by carriage movement
Yes, No
before printing starts.
Yes: Detects paper out and halts printing;
Paper End Detect
Yes, No
otherwise, ignores paper out and continues
printing.
Form Length Ctrl
Software, Ignore
Ignore: Ignores form length commands.
Pitch Ctrl
Software, Ignore
Ignore: Ignores CPI commands.
Font Ctrl
Software, Ignore
Ignore: Ignores font select commands.
Quality Ctrl
Software, Ignore
Ignore: Ignores print quality commands.
Buzzer
Yes, No
Yes: Sounds buzzer on all hardware errors.
23
Tally Dascom 1325
German (Deutsch)
System Setup
Valid Settings
Emulation
ESC/P2, IBM 2390 Plus
Auto CR (IBM)
Ja, Nein
Auto LF
Ja, Nein
Druck Dir
Bi-Dir, Uni-Dir, Auto
Top Druck Dir
Bi-Dir, Uni-Dir
Anschlag
Normal, Stark
IBM AGM
Ja, Nein
Druck Setup
Valid Settings
Font (Andere)
OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR
Zeichenteilung
10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS
Null
0,Ø
HS-Draft
An, Aus
Graphikgeschw.
Normal, Schnell, Ultra
IBM Set ½
Set 1, Set 2
USA, Frankreich, Deutschland, UK, Dänemark, Schweden,
Italien, Spanien, Japan, Norwegen, Dänemark II, Spanien II,
Land
Latein-Amerika, Korea, Legal
Zeichensatz
CP 437, CP 857…
Zeichentabelle
Graphik, Italic
Seiten Setup
Valid Settings
Zeilen Pro Zoll
1, 2, 3, 4, 5, 6, 7, 8
Endlos Formularlänge
3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
Endlos Oberer Rand
0/60" … 10/60"…99/60"
Endlos Unterer Rand
0/60"…10/60"...30/60"
Einzel Formularlänge
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
Einzel Oberer Rand
0/60" … 10/60"…99/60"
Einzel Unterer Rand
0/60"…10/60"...30/60"
Rollenpapier
Ja, Nein
Perforationssprung
Ja, Nein
Abreissen
Manuell, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Auswurfrichtung
Vorne, Hinten
Beleg
Aus, An
24
Tally Dascom 1325
Schnittstellen Setup
Valid Settings
Schnittstelle
Auto, Parallel, USB
I-PRIME
Ja, Nein
Auto IF Delay
10s, 30s
RAM Nutzung
Ladbarer Font, Puffer
CX Bid
Ja, Nein
Erweitertes Setup
Valid Settings
Auto Laden
Manuell, 0.5s, 1s, 1.5s, 2s
Papierstau Vorbeugung
Ja, Nein
Papierende Detekt
Ja, Nein
Formularlänge Strg
Software, Ignoriere
Zeichenteilung Strg
Software, Ignoriere
Font Strg
Software, Ignoriere
Qualität Strg
Software, Ignoriere
Summer
Ja, Nein
Russian (Россия)
Системные установки
Valid Settings
Эмуляция
ESC/P2, IBM 2390 Plus
Авто CR (IBM)
Да, Нет
Авто LF
Да, Нет
Направление печати
Двунаправленная, Однонаправленная, Авто
Направление печати загл. букв
Двунаправленная, Однонаправленная
Удар
Нормальный, Сильный
IBM AGM
Да, Нет
Valid Settings
Настройка печати
Дополнительный шрифт
OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR
знаков/дюйм
10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS
Перечеркнутый ноль
0,Ø
Высокая скорость
Вкл, Выкл
Скорость графики
Нормальная, Быстрая, Очень быстрая
Символы IBM 1/2
Уст. 1, Уст. 2
USA, France, Germany, UK, Дания, Sweden, Italy, Spain,
Набор знаков
Japan, Норвегия, Дания II, Spain II, Латин
ская Америка, Korea, Legal
Кодовая таблица
CP 437, CP 857…
Таблица знаков
Графика, Курсив
25
Tally Dascom 1325
Параметры страницы
Valid Settings
Строк на дюйм
1, 2, 3, 4, 5, 6, 7, 8
Длина формы для непрерывной
бумаги
Отступ сверху для непрерывной
бумаги
Отступ снизу для непрерывной бумаги
Длина формы для отдельных листов
3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
0/60" … 10/60"…99/60"
0/60"…10/60"...30/60"
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14",
17"
Отступ сверху для отдельных листов
0/60" … 10/60"…99/60"
Отступ снизу для отдельных листов
0/60"…10/60"...30/60"
Рулонная бумага
Да, Нет
Пропуск перфорации
Да, Нет
Авто прогон
Ручной, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Выход бумаги
Перед, Зад
Спящий режим
Выкл, Вкл
Valid Settings
Установки интерфейса
Интерфейс
Авто, Паралел, USB
Паралел. порт
Да, Нет
Время ожидания
10s, 30s
Назначение RAM
Пользов. шрифт, Буфер
CX Bid
Да, Нет
Дополнительные установки
Valid Settings
Автозагрузка
Ручная, 0.5s, 1s, 1.5s, 2s
Датчик движ. бумаги
Да, Нет
Датчик конца бумаги
Да, Нет
Контоль длины формы
Програмный, Игнор.
Контроль знаков/дюйм
Програмный, Игнор.
Контроль шрифта
Програмный, Игнор.
Контроль качества
Програмный, Игнор.
Звук
Да, Нет
26
Tally Dascom 1325
Italian (Italiano)
Menu Sistema
Valid Settings
Emulazione
ESC/P2, IBM 2390 Plus
Auto CR (IBM)
Si, No
Auto LF
Si, No
Direz. Stampa
Bi-Dir, Uni-Dir, Auto
Top Print Dir
Bi-Dir, Uni-Dir
Impatto
Normale, Pesante
IBM AGM
Si, No
Menù Stampa
Valid Settings
Fonte (Altre)
OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR
Spaziatura
10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS
Zero
0,Ø
HS-Bozza
Si, No
Veloc. Grafica
Normale, Veloce, Ultra
IBM Set 1/2
Set 1, Set 2
USA, Francia, Germania, Regno Unito, Danimarca, Svezia,
Set Carat. Int.
Italia, Spagna, Giappone, Norvegia, Danimarca II, Spagna II,
America Latina, Korea, Legal
Code Page
CP 437, CP 857…
Tab.Carattere
Tab. Grafica, Italico
Menù Pagina
Valid Settings
Interlinea
1, 2, 3, 4, 5, 6, 7, 8
Lungh. Mod. Continuo
3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
Margine Sup. Continuo
0/60" … 10/60"…99/60"
Margine Inf. Continuo
0/60"…10/60"...30/60"
Lunghezza Foglio
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
Margine Sup. Foglio
0/60" … 10/60"…99/60"
Margine Infer. Foglio
0/60"…10/60"...30/60"
Rullo Carta
Si, No
Salto Perforazione
Si, No
Autostrappo
Manuale, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Uscita Carta
Frontale, Posteriore
Scontrino
Si, No
27
Tally Dascom 1325
Menù Interfacc.
Valid Settings
Interfaccia
Auto, Parallela, USB
I-PRIME
Si, No
Ritardo Auto IF
10s, 30s
Uso RAM
Fonti utente, Memoria
CX Bid
Si, No
Menù Avanzato
Valid Settings
Autocaricamento
Manuale, 0.5s, 1s, 1.5s, 2s
Previene Inceppamento
Si, No
Rileva Fine Carta
Si, No
Control. Lungh. Carta
Software, Ignora
Control. Spaziatura
Software, Ignora
Controllo Fonti
Software, Ignora
Controllo Qualità
Software, Ignora
Cicalino
Si, No
French (Français)
Setup système
Valid Settings
Emulation
ESC/P2, IBM 2390 Plus
RC-Auto (IBM)
Oui, Non
SL-Auto
Oui, Non
Dir Impr.
Bidir, Unidir, Auto
Sup. Dir Impr.
Bidir, Unidir
Frappe
Normal, Forte
IBM AGM
Oui, Non
Setup impression
Valid Settings
Polices (Autres)
OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR
Densités caract.
10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS
Zéro
0,Ø
HS-Draft
Oui, Non
Vitesse graphiq.
Normal, Rapide, Ultra
IBM Set 1/2
Set 1, Set 2
USA, France, Allemagne, Royaume-Uni, Denmark, Suède, Italie,
Pays
Espagne, Japon, Norvège, Denmark II, Espagne II, Amerique
latine, Korea, Legal
Jeu de caractèr.
CP 437, CP 857…
Tabl.de caract.
Graphque, Italique
28
Tally Dascom 1325
Setup page
Valid Settings
Lignes par pouce
1, 2, 3, 4, 5, 6, 7, 8
Papier continu Longueur formulaire
3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
Papier continu Bord supérieure
0/60" … 10/60"…99/60"
Papier continu Bord inférieure
0/60"…10/60"...30/60"
Feuille à feuille Longueur formulaire
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
Feuille à feuille Bord supérieur
0/60" … 10/60"…99/60"
Feuille à feuille Bord inférieur
0/60"…10/60"...30/60"
Papier du rouleau
Oui, Non
Sauter la perforation
Oui, Non
Coupe Auto
Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Direction de sortie
Avant, Arrière
Slip
Arrêt, Marche
Setup interface
Valid Settings
Interface
Auto, Parallel, USB
I-PRIME
Oui, Non
Auto IF Delay
10s, 30s
Utilisation RAM
User Font, Buffer
CX Bid
Oui, Non
Setup élargi
Valid Settings
Chargem. Autom.
Manuel, 0.5s, 1s, 1.5s, 2s
Prévention bourrage
Qui, Non
Détec.fin de pap
Qui, Non
Long.formul.Strg
Software, Ignorer
Densi.caract.Strg
Software, Ignorer
Police Strg
Software, Ignorer
Qualité Strg
Software, Ignorer
Vibrateur
Qui, Non
29
Tally Dascom 1325
Spanish (Español)
System Setup
Valid Settings
Emulación
ESC/P2, IBM 2390 Plus
Auto CR(IBM)
Si, No
Auto LF
Si, No
ModoImpresión
Bi-Dir, Uni-Dir, Auto
ModoImp.Borde
Bi-Dir, Uni-Dir
Impacto
Normal, Fuerte
IBM AGM
Si, No
Print Setup
Valid Settings
Fuente (Otros)
OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR
Tamaño Letra
10cpp, 12cpp, 15cpp, 17cpp, 20cpp, PS
Cero
0,Ø
Alta Velocidad
Activado, Desactivado
Imp. Grafica
Normal, Rápido, Ultra
IBM Juego 1/2
Juego 1, Juego 2
USA, Francia, Alemania, Reino Unido, Dinamarca, Suecia, Italia,
Carácter Local
España, Japón, Noruega, Dinamarca II, España II,
AméricaLatina, Corea, Legal
Tabla Carácter
CP 437, CP 857…
Tipo Tabla
Tabla Gráfica, Italica
Page Setup
Valid Settings
Lineas Por Pulgada
1, 2, 3, 4, 5, 6, 7, 8
Tamaño Papel Continuo
3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
Margen Sup. Pap Cont.
0/60" … 10/60"…99/60"
Margen Inf. Pap.Cont.
0/60"…10/60"...30/60"
Tamaño Hojas Sueltas
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
Margen Sup. Folios
0/60" … 10/60"…99/60"
Margen Inf. Folios
0/60"…10/60"...30/60"
Rollo de Papel
Si, No
Salto perforación
Si, No
Mover a PosiciónCorte
Manual, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Expulsión de papel
Delante, Atrás
Ajustes
Apagado, Encendido
30
Tally Dascom 1325
Interface Setup
Valid Settings
Interface
Auto, Paralelo, USB
I-Prime
Si, No
Auto retraso
10s, 30s
Uso de RAM
Font Usuario, Buffer
CX Bid
Si, No
Advanced Setup
Valid Settings
Auto Carga
Manual, 0.5s, 1s, 1.5s, 2s
Prevención Atascos
Si, No
Detección Fin Papel
Si, No
Control Tamaño Papel
Software, Ignorar
Control Tamaño Letra
Software, Ignorar
Control Fuente
Software, Ignorar
Control Calidad
Software, Ignorar
Alarma
Si, No
Turkish (Türkce)
Sistem Ayarı
Valid Settings
Benzetim/Emulation
ESC/P2, IBM 2390 Plus
Otom. Satırbaşı (IBM)
Evet, Hayır
Otom. Satır besleme
Evet, Hayır
Yazdırma yönü
İki-Yöne, Tek-Yöne, Otom.
Üstte yazdırma yönü
İki-Yöne, Tek-Yöne
Vuruş
Normal, Güçlü
IBM AGM
Evet, Hayır
Yazdırma Ayarları
Valid Settings
Yazı Tipi (Diğer)
OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR
Karakter Sıklığı
10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS
Sıfır
0,Ø
Yük.Hız-Taslak
On, Off
Grafik Hızı
Normal, Hızlı, Ultra
IBM Karakter Seti 1/2
Set 1, Set 2
Uluslararası Kar. Seti
İsveç, İtalya, İspanya, Japonya, Norveç, Danimarka II, İspanya
Amerika Bir.Devleti, Fransa, Almanya, İngiltere, Danimarka,
II, Latin Amerika, Korea, Legal
Kod Sayfası
CP 437, CP 857…
Karakter Tablosu
Grafik Tablosu, İtalik
31
Tally Dascom 1325
Sayfa Düzeni Ayarı
Valid Settings
İnç başına satır
1, 2, 3, 4, 5, 6, 7, 8
Sürekli-kağıt Form Uzunluğu
3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17"
Sürekli-kağıt Üst kenar boşluğu
0/60" … 10/60"…99/60"
Sürekli-kağıt Alt kenar boşluğu
0/60"…10/60"...30/60"
Tek-kağıt Form uzunluğu
3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"
Tek-kağıt Üst kenar boşluğu
0/60" … 10/60"…99/60"
Tek-kağıt Alt kenar boşluğu
0/60"…10/60"...30/60"
Rulo kağıt
Evet, Hayır
Delik atlama
Evet, Hayır
Otom. Koparma
Elle/Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Çıkartma Yönü
Önden, Arkadan
Makbuz/Fiş
Kapalı, Açık
Arabirim Ayarları
Valid Settings
Arabirim
Otom., Paralel, USB
I-Prime
Evet, Hayır
Otom. Arabirim gecikmesi
10s, 30s
RAM Kullanımı
Kullanıcı Yazı Tipi, Arabellek
CX Bid
Evet, Hayır
Valid Settings
Geliştirilmiş Ayarlar
Otom. Yükleme
Elle/Manuel, 0.5s, 1s, 1.5s, 2s
Kağıt Sıkışmasını Önleme
Evet, Hayır
Kağıt Sonunu Algılama
Evet, Hayır
Form Uzunl. Kont.
Yazılım, Yoksay
Karak.Sıkl. Kont.
Yazılım, Yoksay
Yazı Tipi Kont.
Yazılım, Yoksay
Kalite Kont.
Yazılım, Yoksay
Alarm Zili
Evet, Hayır
32
Tally Dascom 1325
Vertical Alignment
The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing.
Adjust Vertical Alignment Procedure:
1. Enter the Service Menu by holding down the【Tear/Off】and【LF/FF】keys while powering up.
2. Load paper.
3. The printer will print as follows:
Service Menu
【LF/FF】= OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit
Current Setting:Vertical Alignment
4. Press【LF/FF】key to select the current setting. The printer will print as follows:
Vertical Alignment
【LF/FF】= OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit
Please select Paper Type:Single Ply
For single ply paper, press【LF/FF】key to select. For multipart paper, press 【Load/Eject】key to go
to “Multipart”,then press【LF/FF】key to select.
5. If single ply is selected for paper type, the following will print:
Single Ply
Current Print Mode: LQ
Press 【Load/Eject】key to scroll to other print modes if required.
6. If LQ is selected, the following will print:
LQ
【LF/FF】= lower ½ to left 【Load/Eject】= lower ½ to right
【Online】= Exit
LQ -2:
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Pressing 【LF/FF】or 【Load/Eject】 key will allow you to adjust the alignment of the vertical lines
33
Tally Dascom 1325
printed above.
7. Once the setting which gives the best alignment is found, press 【Online】 key to exit current level.
Printer will print “Save settings? Yes”. Press 【LF/FF】 key to save setting. Press 【Online】 key a few
times until the printer exits the Service Menu.
Change Pin Function
When printer has been used for a long time or the print volume is high, the frequently used print head pins
may fail. The Change Pin function enables the user to continue using the printer for a while without
compromise in print quality until a suitable print head replacement is available. This function will reduce the
print speed if activated.
Change Pin Procedure:
1. Enter the Service Menu by holding down the【Tear/Off】and【LF/FF】keys while powering up.
2. Load paper.
3. The printer will print as below:
Service Menu
【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit
Current Menu:Vertical Alignment
Press 【Load/Eject】 key to scroll to “Change Pin”,then press 【LF/FF】 key to select. The status
of each pin will be printed as follows:
Change Pin
1 ---------- Is this pin OK? Yes / No
2 ---------- Is this pin OK? Yes / No
3 ---------- Is this pin OK? Yes / No
24 ---------- Is this pin OK? Yes / No
Press 【Load/Eject】 key to choose whether the pin is Yes or No,then press 【LF/FF】 key to confirm
selection.
4. When all the 24 pins are evaluated, press 【Online】. The printer will print “Save settings? Yes”. Press
【LF/FF】 key to confirm selection. Press 【Online】 key a few times until the printer exits the Service
Menu.
34
Tally Dascom 1325
Adjust Physical Margins
Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once
these settings are changed, resetting the printer to factory defaults will not initialize these settings back to
the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary.
Adjust Top Margin Procedure:
1. Enter the Adjust Page Margins function by holding down the【Load/Eject】and【Online】keys while
powering up until the printer beeps twice.
2. Load paper.
3. The printer will print as below:
Adjust Page Margins:
【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit
Current Setting: Adjust Fanfold Top Margin
Press【LF/FF】key to confirm selection if the paper used is fanfold type. The printer will print as
follows:
Procedure:
Install fanfold paper to tractors
【LF/FF】 = Add 【Load/Eject】 = Reduce 【Online】 = Exit
Each step is 0.5 mm
Function of keys:
【Tear Off】key: Decrease 0.5mm
【Load/Eject】key: Increase 0.5mm
4. Press 【LF/FF】 key, printer will print “Save settings?Yes”. Press 【Load/Eject】 key to choose Yes
or No,then press 【LF/FF】 key to confirm selection and exit “Adjust Page Margins” mode by
pressing 【Online】. The print head moves to the left side and the printer beeps twice, then the print
head moves to the middle position.
Adjust Left Margin Procedure:
1. Enter the Adjust Page Margins function by holding down the【Load/Eject】and【Online】keys while
powering up until the printer beeps twice.
2. Load paper.
3. The printer will print as below:
Adjust Page Margins:
【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit
Current Setting: Adjust Fanfold Top Margin
4. Press【Load/Eject】key until the current setting is “Adjust Fanfold Left Margin”. Press【LF/FF】key to
confirm selection if the paper used is fanfold type. The printer will print as follows:
Adjust Fanfold Left Margin
35
Tally Dascom 1325
Function of keys:
【Tear Off】key: Decrease 0.5mm
【Load/Eject】key: Increase 0.5mm
5. Press 【LF/FF】 key, printer will print “Save settings?Yes”. Press 【Load/Eject】 key to choose Yes
or No,then press 【LF/FF】 key to confirm selection and exit “Adjust Page Margins” mode by
pressing 【Online】. The print head moves to the left side and the printer beeps twice, then the print
head moves to the middle position.
Adjust Tear-Off Position Procedure:
1. Enter the Adjust Page Margins function by holding down the【Load/Eject】and【Online】keys while
powering up until the printer beeps twice.
2. Load fanfold paper
3. The printer will print as below:
Adjust Page Margins:
【LF/FF】=OK 【Tear/Off】= Back 【Load/Eject】= Next 【Online】= Exit
Current Setting: Adjust Fanfold Top Margin
4. Press【Load/Eject】key until the current setting is “Adjust Tear-Off Position”. Press【LF/FF】key to
confirm selection. The printer will print as follows:
Procedure:
Install fanfold paper to tractors
【LF/FF】 = Add 【Load/Eject】 = Reduce 【Online】 = Exit
Each step is 0.5 mm
Function of keys:
【Tear Off】key: Decrease 0.5mm
【Load/Eject】key: Increase 0.5mm
5. Press 【LF/FF】 key, printer will print “Save settings?Yes”. Press 【Load/Eject】 key to choose Yes
or No,then press 【LF/FF】 key to confirm selection and exit “Adjust Page Margins” mode by
pressing 【Online】. The print head moves to the left side and the printer beeps twice, then the print
head moves to the middle position.
36
Tally Dascom 1325
Dascom Printer Setup Tool
In the CDROM is a software utility called “Dascom Printer Setup”. This application enables a convenient,
simple and fast way to control your printer without touching any keys on the operation panel.
1. Start the tool installation by double clicking the “Dascom Printer Setup.exe”.
2. Connect the printer to the system using USB cable
3. Power up the printer.
4. Load paper into the printer. (Note: The tool cannot get connected to the printer when the printer is
offline.)
5. Run the tool from the Windows Start menu by selecting All Programs, then Dascom Printer Setup,
and then Tally Dascom Printer Setup.
6. For more information on how to use the tool, go to the Help menu and select User Guide.
37
Tally Dascom 1325
6 Maintenance
Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is
required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is
sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly
back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact
your dealer to determine whether lubrication may be necessary.
Switch printer off and unplug the power cord from
the mains before doing any maintenance work.
Cleaning
The housing and the top cover of the printer help protect it against dust, dirt, and other contaminants.
However, paper produces small particles that accumulate inside the printer. This section explains how to clean
and vacuum the printer and how to clean the paper bail rollers. It is easier to clean the printer when the cover
is open.
Cleaning and Vacuuming the Printer
If the print head carriage does not move smoothly back and forth or paper particles have accumulated in the
printer, clean the printer.
To clean and vacuum the printer:
1. Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer
power cord.
2. Using a soft vacuum brush, vacuum the exterior of the printer. Also vacuum the cut sheet edge.
3. Use a soft, damp cloth to wipe the exterior of the printer, including the cover. A mild detergent may be
used. Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer.
4. Open the cover of the printer and remove the ribbon cartridge. Using a soft vacuum brush, gently vacuum
the platen, the print head carriage and shaft, and surrounding areas. You can easily slide the print head to
the left or right when the power is off. Be careful not to press too hard on the flat head cable that extends
from the print head carriage.
5. Re-install the ribbon cartridge.
6. Remove the single sheet feeder and clean the form tractors and the surrounding areas.
7. Re-install the single sheet feeder.
Cleaning the Paper Rollers
Clean the platen and paper bail rollers occasionally or when stains or smudges appear on the paper. Use a mild
detergent as appropriate. Do not use alcohol to clean the platen or the rollers. Alcohol may cause the rubber to
harden.
To clean the rollers and the platen:
1. Apply a small amount of water to a soft cloth. Avoid spilling liquid inside the printer.
2. Place the cloth against the platen and manually rotate the paper feed knob.
3. Repeat this procedure for each roller.
38
Tally Dascom 1325
4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed
knob.
39
Tally Dascom 1325
7 Troubleshooting
Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on
some of the common problems you may encounter and how you may solve them. If you encounter problems
that you cannot resolve, contact your dealer or service partner for assistance.
Print Quality Problems and Solutions
Problem
Solution
• Make sure that the ribbon cartridge is properly installed and that
the ribbon feeds smoothly.
Printing is too light or too dark.
• Replace the ribbon if necessary.
• Make sure that the print gap lever is set for the thickness of your
paper.
• Make sure that the print gap lever is set for the thickness of your
paper.
Smears and stains appear on the
• Check for ribbon wear. Replace the ribbon if necessary.
page.
• Check whether the tip of the print head is dirty. Clean the head
with a soft cloth if necessary.
• The print head may need to be replaced.
• Make sure that the interface cable is securely connected to both
Printing is erratic or the wrong
characters are printed. Many “?”
or unexpected characters are
printed.
the printer and computer.
• Make sure that the printer driver selected in your software is the
same as the emulation selected on the printer.
• Check the length of the interface cable. (Maximum Parallel &
USB: 2 meters)
• Try another interface cable.
The page is blank.
• Make sure that the ribbon cartridge is properly installed.
• Make sure the gap lever is set correctly.
Printing is vertically misaligned
Use the printer's vertical alignment function to check the vertical
(jagged).
print alignment. If necessary, adjust the print alignment.
The top margin is wrong.
Lines are double spaced instead of
single spaced.
The printer overprints on the same
line.
• Check the application top margin setting.
• Adjust the Top Margin setting in Page Setup menu if necessary.
Change the Auto LF setting in the System Setup menu to No.
Change the Auto CR setting in the System Setup menu to No.
The next print line starts where
the previous line ended instead of
Change the Auto CR setting in the System Setup menu to Yes.
at the left margin.
40
Tally Dascom 1325
Paper Handling Problems and Solutions
Problem
Solution
• Make sure that the paper select lever located on the top right of
Paper cannot be loaded or fed.
the printer is set correctly. Move the lever to the front for single
sheets or to the rear for continuous forms.
• Make sure that the paper covers the paper-out sensor.
• Turn off the printer and remove the jammed paper. Remove any
obstructions from the paper path.
• Make sure that the Print Gap lever is set for the thickness of
Paper jams while loading.
your paper.
• Make sure that the paper is not folded, creased, or torn.
• Make sure that the left and right tractors are set so that the
continuous forms are stretched taut.
• Turn off the printer and remove the jammed paper. Remove any
obstructions from the paper path.
• Make sure that the Print Gap lever is set for the thickness of
Paper jams while printing.
your paper.
• For continuous forms, make sure that the incoming and
outgoing paper stacks are correctly placed. Paper should feed
straight.
Paper slips off the forms tractors
Make sure that the forms tractors are positioned correctly for the
or the perforated holes of the
width of your paper and that the perforated holes of the paper fit
paper tear during printing.
directly over the tractor pins.
Operating Problems and Solutions
Problem
Solution
• Check whether the mains voltage is correct.
• Make sure that the power cord is securely connected to both
the printer and the mains power outlet.
The power does not turn on.
• Make sure that the power outlet is functional. If not so, use
other outlet.
• Turn the power off. Wait a minute and then turn the printer on
again. If the printer still has no power, contact your dealer.
41
Tally Dascom 1325
• Make sure that the Online indicator is lit.
• If you use the interface cable, make sure it is securely
connected to both the printer and the computer.
The printer is on but it will not
print.
• Make sure paper is loaded.
• Run the printer Status Page. If printing executes normally, the
problem is caused by: the interface, the computer, incorrect
printer settings, or incorrect software settings.
• Make sure that the printer driver selected in your software is the
same as the emulation selected on the printer.
If paper is loaded and the paper select lever is moved to the
Paper select lever error
incorrect position, the printer turns offline, and the buzzer sounds
continuously. Switch the paper select lever back to its correct
position.
Printer Failures
A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the
printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner.
Error Indications on LEDs
Error Description
Operation
Status
Paper
Out LED
Online
LED
Tear Off
LED
Buzzer
Sound
Paper jammed
Suspend
Flash
Off
Flash
Once
Friction feed /Tractor feed
Suspend
Flash
Flash
No change
Continuously
Print head hot
Normal
No change
Flash
No change
--
Carriage initial position
Stop
Flash
Off
Off
Once
EEPROM
Normal
Off
Flash
Flash
Once
Print head cold
Suspend
Flash
Flash
No change
--
ROM error
Stop
Flash
Flash
Flash
Once
42
Tally Dascom 1325
Diagnostic Functions
The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment.

Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware
is functional, any problems you are having are probably caused by incorrect printer settings, incorrect
software settings, the interface, or the computer.

HEX-DUMP MODE: Allows you to determine whether the computer is sending the correct commands
to the printer, and whether the printer is executing the commands correctly. This function is useful to
programmers or others who understand how to interpret hex dumps.

PRINTING ALIGNMENT ADJUSTMENT: Allows you to check and, if necessary, correct the printer’s
vertical line print alignment in bi-directional mode.
For details on using these functions, please refer to chapters 4 and 5.
43
Tally Dascom 1325
Firmware Update
Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained
from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is
strongly recommended to print the Main Menu page to keep a record of the old settings.
Note: Firmware update should only be performed by an authorized service person. We disclaim any
responsibility for any damage caused if it is performed by any other person.
To load new firmware, proceed as follows:
1. Switch off the printer. Connect your PC to the parallel port on the printer.
2. Press and hold down 4 keys (S1, S2, S3, S4) while powering on the printer.
3. Alternate flashing of L1 and L4 LEDs indicates printer is ready for firmware update.
4. Go to the DOS prompt window. Copy the firmware file (with extension .MOT) to your printer as
follows:
COPY /B .mot PRN
5. When new firmware is being received, L1 and L4 will flash together, followed by L1 and L3 flashing
together.
Note: Do not interrupt the downloading process to prevent possible flash memory corruption.
6. When downloading is completed, the carriage returns to home position. Printer initializes normally.
Alternatively, you can use the Firmware Flash Tool version 3.5 or higher which is available in the CDROM and
our website as well. Upon starting up the tool, choose the correct file and press "Update".
44
Tally Dascom 1325
8 General Specifications
Print System
Mono-chrome serial impact dot matrix
Print Technology
Uni-/bi-directional logic seeking for text and graphics
Print Speed
Font Matrix
Print Head
Graphics
Pitch
HS Draft
Draft
LQ
10 CPI
375/80H
250/120H
83/360H
12 CPI
300/120H
300/120H
100/360H
15 CPI
375/120H
375/120H
125/360H
17.1 CPI
426/120H
426/120H
142/360H
20 CPI
498/120H
498/120H
166/360H
Pitch
HS Draft
Draft
LQ
10 CPI
8x24/80H
12x24/120H
36x24/360H
12 CPI
10x24/120H
10x24/120H
30x24/360H
15 CPI
8x16/120H
8x16/120H
24x16/360H
17.1 CPI
7x24/120H
7x24/120H
21x24/360H
20 CPI
6x24/120H
6x24/120H
18x24/360H
Proportional
Nx24/360H
Nx24/360H
Nx24/360H
Number of pins:
24 pins
Firing frequency:
Normal mode: 1500 Hz
Pin diameter:
0.2 mm
Life:
400 million strokes/pin @ Draft mode
8-bit mode: 8V x 60H, 80H, 90H, 120H, 240H (DPI)
24-bit mode: 24V x 60H, 90H, 120H, 180H, 360H (DPI)
Paper
Feed Speed
Continuous feed: 5.0 IPS (inches per second)
Resolution
360 x 360 DPI maximum
Characters per line (CPL)
Printable
Columns
(CPS/DPI)
10 CPI:
80 CPL
12 CPI:
96 CPL
15 CPI:
120 CPL
17.1 CPI:
137 CPL
20 CPI:
160 CPL
45
(Matrix/DPI)
Tally Dascom 1325
Bitmap Fonts:
1. Draft 10, 12, 15, 17, 20 CPI
2. Roman 10, 12, 15, 17, 20 CPI, Proportional
3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional
4. Courier 10, 12, 15, 17, 20 CPI, Proportional
5. Prestige 10, 12, 15, 17, 20 CPI
6. OCR-B 10, 12, 17, 20 CPI
Built-In Fonts
7. OCR-A 10, 12, 17, 20 CPI
8. Orator 10, 12, 15, 17, 20 CPI, Proportional
9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional
10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional
11. Script 10, 12, 15, 17, 20 CPI
1. EAN-13
2. EAN-8
3. Interleaved 2 of 5
4. UPC-A
5. UPC-E
Barcodes
6. Code 39
7. Code 128
8. POSTNET
9. Codabar
10. Industrial 2 of 5
1. CP 437
2. CP 737
3. CP 850
4. CP 851
5. CP 852
6. CP 857
7. CP 858
8. CP 860
9. CP 861
Code Pages
10. CP 863
11. CP 864
12. CP 864 Extended
13. CP 865
14. CP 866 Cyrillic
15. CP 866 Bulgaria
16. CP 1250
17. CP 1251
18. CP 1252
19. CP 1253
20. CP 1254
46
Tally Dascom 1325
21. 8859-1
22. 8859-1 (SAP)
23. 8859-2
24. 8859-5
25. 8859-7
26. 8859-9
27. 8859-15
28. BRASCII
29. Abicomp
30. Roman8
Code Pages
31. Coax/Twinax
32. New-437
33. New-Dig 850
34. Old-Code 860
35. Flarro 863
36. 865 Hebrew
37. CP 1257
38. 866 Ukraine
39. 866 Kazakhstan
40. Kamenicky
41. Mazovia
42. CP 775
43. CRO-ASCII
44. Arabic Farsi
45. Arabic Urdo
46. Greek DEC
47. Greek ELOT 928
1. USA
2. France
3. Germany
4. UK
5. Denmark I
6. Sweden
7. Italy
International
Character Sets
8. Spain I
9. Japan
10. Norway
11. Denmark II
12. Spain II
13. Latin America
14. Korea
15. Legal
47
Tally Dascom 1325
Line Spacing
1/6", 1/8", n/60", n/180", n/360"
Fanfold Paper
Cut Sheet
Single ply
Paper
Specifications
Multi-part
Width:
55mm~297mm
Width: 55mm~297mm (2.2"~11.7")
(2.2"~11.7")
Length:
Length: 139.7mm min (5.5" min)
55mm~363.2mm
(2.2"~14.3")
Paper
Specifications
Weight: 52~100g/㎡
Weight: 52~100 g/㎡
Thickness:
Thickness:
0.065~0.14mm
0.065~0.14mm
(0.0026"~0.0055”)
(0.0026"~0.0055")
Feeding method: Friction and Tractor
Paper Handling
Paper path:
Cut sheets: Front in, front or rear out
Fanfold: Rear in, front out
Copy Capability
Original + 6 copies
Emulation
ESC/P2, IBM 2390 Plus
Ribbon Type
Cartridge; Monochrome
Ribbon Life
7 million characters (rolling Draft 10 CPI)
Input Data Buffer
Up to 92KB
Windows Server 2000/2003/2008
Windows Vista
Windows Drivers
Windows XP
Windows 98
Windows 7
Interface
Parallel (Bi-directional IEEE-1284 nibble mode)
USB 2.0 (B type connector)
Operation Panel
Noise Level
Switches: 4 pcs
LED indicators: 4 pcs
< 53 dBA in 10CPI draft ASCII (Conforming to ISO7779)
48
Weight: 40~58g/㎡
Thickness: 0.45 mm max
(0.0177” max)
Tally Dascom 1325
Temperature Operating:
Stand-by:
Ambient
Conditions
Humidity
+5 to +40 °C.
-20 to +55 °C
Operating:
10 to 90%RH
(No condensation)
Stand-by:
10 to 85%RH
(No condensation)
Dimensions
404 mm (W) x 322 mm (D) x 203 mm (H)
Weight
5 kg
Power Supply
Unit type:
Switching mode power supply
Power cord:
Detachable
Voltage rating:
AC 230V (180V~264V), 50Hz to 60Hz
AC 110V/120V, 60Hz (factory option)
Stand by:
Less than 5.9W
ESD:
Comply with IEC801-2
Contact discharge: 4kV
Air discharge:
8kV
Power
consumption
34.8 W (standard ECMA-132)
MTTR
< 20 minutes
MTBF
10000 hours @ 25% duty cycle
Certification
CE, UL, FCC, ES, ISTA, RoHS, WEEE, REACH, ChemVerbotsV,
Microsoft Certified for Windows 7
49
Tally Dascom 1325
9 Interfaces
Parallel Interface
Parallel Interface Pin Assignment
Pin
Signal Name
Signal Transmission
STROBE
¯¯¯¯¯¯
Printer  Computer
2~9
DATA
Printer  Computer
10
ACK
¯¯¯
Printer  Computer
11
BUSY
Printer  Computer
12
PE
Printer  Computer
13
SELECT
Printer  Computer
14
AFXT
¯¯¯¯
Printer  Computer
15
Unused
Unused
16
GND
Printer  Computer
17
F-GND
Printer  Computer
18
+5V
Printer  Computer
19~30
GND
Printer  Computer
31
INIT
¯¯¯¯
Printer  Computer
32
FAULT
¯¯¯¯¯
Printer  Computer
33
GND
Printer  Computer
34
Unused
Unused
35
FUSE
Printer  Computer
36
SLCTIN
¯¯¯¯¯¯
Printer  Computer
Parallel Interface Connector Diagram
Note: Any external devices connected to the parallel port should not draw current exceeding 200 mA from pin
18; otherwise it may affect the printer operation.
USB Interface
The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at
12 Mbps. It uses the “B” type USB connector.
50
Tally Dascom 1325
10 Character sets & Code Pages
Character Sets
Standard Character Set 1
Standard Character Set 2
51
Tally Dascom 1325
IBM Character Set 1
IBM Character Set 2
52
Tally Dascom 1325
International character sets
International Character Set Commands
Country
USA
Command
<ESC>“R”CHR$(0)
France
<ESC>“R”CHR$(1)
Germany
<ESC>“R”CHR$(2)
UK
<ESC>“R”CHR$(3)
Denmark1
<ESC>“R”CHR$(4)
Sweden
<ESC>“R”CHR$(5)
Italy
<ESC>“R”CHR$(6)
Spain1
<ESC>“R”CHR$(7)
Japan
<ESC>“R”CHR$(8)
Norway
<ESC>“R”CHR$(9)
Denmark2
<ESC>“R”CHR$(10)
Spain2
<ESC>“R”CHR$(11)
Lat America
<ESC>“R”CHR$(12)
Korea
<ESC>“R”CHR$(13)
Legal
<ESC>“R”CHR$(64)
53
Tally Dascom 1325
Character Tables
Italic
54
Tally Dascom 1325
Graphic 1
Graphic 2
55
Tally Dascom 1325
Code Page Commands
Code Page
ESC R Parameter
CRO-ASCII
3C
Arabic Farsi
96
Arabic Urdo
97
Greek DEC
46
Greek ELOT 928
6C
CP437 Latin US
80
CP737 Greek
93
CP850 Latin 1
82
CP851 Greek
88
CP852 Latin 2
87
CP857 Turkish
8D
CP858 (IBM with €)
9E
CP860 Portugal
84
CP861 Icelandic
94
CP863 French Canada
85
CP864 Arabic
8C
CP864 Arab. Extended
95
CP865 Nordic
86
CP866 Cyrillic
8E
CP866 Bulgaria
9D
Siemens Turkish
9B
DEC Turkish
9C
CP1250 Win Latin 2
70
CP1251 Win Cyrillic
71
CP1252 Win Latin 1
72
CP1253 Win Greek
73
CP1254 Win Turkish
74
8859-1 Latin 1
25
8859-1 Latin 1 (SAP)
2B
8859-2 Latin 2
26
8859-5 Cyrillic
2A
8859-7 Greek
2D
8859-9 Turkish
2E
8859-15 Latin 9 (Euro)
2F
BRASCII
6D
Abicomp
6E
Roman 8
4D
56
Tally Dascom 1325
Coax/Twinax(Hebrew)
4F
New-437 (Hebrew)
81
New-DIG 850 (Hebr.)
83
Old-Code 860 (Hebr.)
98
Flarro 863 (Hebrew)
99
Table 865 (Hebrew)
9A
CP775 Baltic
A6
CP1257 Baltic
77
Mazovia (Poland)
92
Kamenicky (Czech)
91
CP866 Ukraine
8F
CP866 Kazakhstan
90
57
Tally Dascom 1325
Code Page Tables
CP 437 (US)
CP 737 Greek
58
Tally Dascom 1325
CP 850 (Multilingual)
CP 851
59
Tally Dascom 1325
CP 852 (Eastern Europe)
CP 857 (Turkish)
60
Tally Dascom 1325
CP 858
CP 860 (Portugal)
61
Tally Dascom 1325
CP 861 (Iceland)
CP 863 (French-Canadian)
62
Tally Dascom 1325
CP 864 Arabic
CP 864 Arabic Extended
63
Tally Dascom 1325
CP 865 (Norway)
CP 866 (Cyrillic)
64
Tally Dascom 1325
CP 866 Bulgaria
CP 1250 Win Latin 2
65
Tally Dascom 1325
CP 1251 Win Cyrillic
CP 1252 Win Latin 1
66
Tally Dascom 1325
CP 1253 Win Greek
CP 1254 Win Turkish
67
Tally Dascom 1325
8859-1 Latin 1
8859-1 Latin 1 (SAP)
68
Tally Dascom 1325
ISO 8859-2 (ISO Latin 2)
ISO 8859-5 Cyrillic
69
Tally Dascom 1325
ISO 8859-7 (Latin/Greek)
ISO 8859-9 (Turkish)
70
Tally Dascom 1325
ISO 8859-15 Euro (Code Page 923)
BRASCII
71
Tally Dascom 1325
Abicomp
Roman 8
72
Tally Dascom 1325
Coax/Twinax (Hebrew)
New-437 (Hebrew)
73
Tally Dascom 1325
New-Dig 850 (Hebrew)
Old-Code 860 (Hebrew)
74
Tally Dascom 1325
Flarro 863 (Hebrew)
865 Hebrew
75
Tally Dascom 1325
CP 1257
866 Ukraine
76
Tally Dascom 1325
866 Kazakhstan
Kamenicky
77
Tally Dascom 1325
Mazovia
CP 775
78
Tally Dascom 1325
CRO-ASCII
Arabic Farsi
79
Tally Dascom 1325
Arabic Urdo
Greek DEC
80
Tally Dascom 1325
Greek ELOT 928
81
Tally Dascom 1325
11 Control Codes Summary
Epson Emulation Command List
Command Sequence
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DC1
DC2
DC3
DC4
CAN
DEL
ESC SO
ESC SI
ESC SP n
ESC EM n
ESC ! n
ESC ( - n1 n2 m d1 d2
ESC $ n1 n2
ESC | n
ESC % n
ESC &
ESC ( ^ n m d1 d2…
ESC (G
NUL d
ESC * m n1 n2…
ESC . c v h m nL nH d1 d2…
ESC + n
ESC – n
ESC / n
ESC ( C NUL n m
ESC ( c NUL nt mt nb mb
ESC ( U NUL n
ESC 0
ESC 2
ESC 3 n
ESC 4
ESC 5
ESC 6
ESC 7
Function
Beeper
Backspace
Tab horizontally
Line feed
Tab vertically
Form feed
Carriage return
Select double-width printing (one line)
Select condensed mode
Online
Cancel condensed mode
Offline
Cancel double-wide mode(one line)
Cancel line
Delete character
Select double-width printing (one line)
Select condensed mode
Set intercharacter space
NA
Print mode setup
Choose character lineation
Select absolute horizontal print position
Set left margin
Select user-defined set
Define user-defined set
Print data in character style
Select graphics mode
Select image mode
Print raster graphics
Select n/360″line spacing
Underline on/off
Select vertical orientation channel
Set page length
Page setup
Set unit
Set 1/8″line spacing
Set 1/6″line spacing
Set n/180″line spacing
Set Italic
Cancel Italic
Enable printable characters
Enable upper control characters
82
Tally Dascom 1325
ESC :
ESC <
ESC >
ESC =
ESC #
ESC ?n m
ESC @
ESC \n1 n2
ESC A n
ESC B…NUL
ESC C n
ESC D…NUL
ESC E
ESC F
ESC G
ESC H
ESC J n
ESC K n1 n2 …
ESC L n1 n2 …
ESC M
ESC N n
ESC O
ESC P
ESC Q n
ESC R n
ESC S n
ESC T
ESC U n
ESC ( V NUL n m
ESC W n
ESC X n1 n2
ESC Y n1 n2 …
ESC Z n1 n2 …
ESC a n
ESC b n
ESC c n m
ESC g
ESC j n
ESC k n
ESC p n
ESC q n
ESC r n
ESC t n
ESC (t nL nH d1 d2 d3
ESC ( v NUL n m
ESC w n
ESC x n
ESC( B n1 n2 k m s v1 v2 c
Copy ROM to RAM
Unidirectional mode(1 line)
Set MSB to 1
Set MSB to 0
Cancel MSB control
Reassign graphics mode
Initialize printer
Set relative horizontal print position
Set n/60″line spacing
Set/cancel vertical tabs
Set page length in lines
Set/cancel horizontal tabs
Select Bold
Cancel Bold
Select double-strike mode
Cancel double-strike mode
Perform tactic n/180″line feed
Select 8 pins single-density graphics
Select 8 pins double–density graphics
Select ELITE(12CPI)
Set bottom margin
Cancel bottom margin
Select PICA(10CPI)
Set right margin
International character set
Select superscript/subscript
Cancel superscript/subscript
Select unidirectional/bidirectional printing mode
Select absolute vertical print position
Turn Double-wide mode on/off
Select font by pitch and point
Select 8 pins, high speed ,double –density graphics
Select 8 pins, high speed fourfold –density graphics
Select justification
Select vertical orientation channel
Set horizontal intercharacter space
Select 15CPI
Perform reverse n/180″line feed
Select typeface
Turn proportional mode on/off
Select character style
Select printing colour
Select character table
Assign character table
Set relative vertical print position
Turn double-high mode on/off
Select print quality
Barcode print
83
Tally Dascom 1325
IBM Emulation Command List
Command Sequence
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DC1
DC2
DC3
DC4
CAN
ESC BEL
ESC BS
ESC HT
ESC CR
ESC LF
ESC SO
ESC SI
ESC DC1
ESC DC2
ESC DC3
ESC DC4
ESC CAN
ESC FF
ESC EM n
ESC :
ESC VT
ESC 0
ESC 1
ESC 2
ESC 3 n
ESC 4
ESC 5 n
ESC 6
ESC 7
ESC =
ESC \
ESC ^
ESC A n
ESC B n
ESC C n
Function
Beeper
Backspace
Tab horizontally
Line feed
Tab vertically
Form feed
Enter
Select double-wide mode
Select condensed mode
Online
Select 10CPI
Offline
Cancel double-wide mode(one line)
Cancel buffer
Beeper
Backspace
Tab horizontally
Enter
Line feed
Select double-wide mode
Select condensed mode
Online
Select 10CPI
Offline
Cancel double-wide mode(one line)
Cancel buffer
Form feed
Automatically Feed Paper mode
Set 12CPI
Tab vertically
Select 1/8″line spacing
Select 7/72″line spacing
Select 1/6″line spacing or activate ESC A n command
Select n/216″or 1/180″line spacing
Set top margin
Automatic Line Feed
Select character set 2
Select character set 1
NA
Print continuously from all character chart
Print single character from all character chart
Select n/72″or n/60″line spacing
Select Tab vertically
Set page length in lines
84
Tally Dascom 1325
ESC C NUL n
ESC D
ESC E
ESC F
ESC G
ESC H
ESC I n
ESC J n
ESC K n1 n2 V1 V2 …Vn
ESC L n1 n2 V1 V2 …Vn
ESC N n
ESC O
ESC P n
ESC Q n
ESC R
ESC S n
ESC T
ESC U n
ESC W n
ESC X n m
ESC Y n1 n2 V1 V2 …Vn
ESC Z n1 n2 V1 V2 …Vn
ESC [- n1 n2 m1 m2
ESC [@ n1 n2 m1 m2 m3 m4
ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc
ESC [ K n1 n2 init id para1 para2 …paran
ESC [ T n1 n2 n3 n4 Hc Lc
ESC [\
ESC [d
ESC [f n1 n2 k m s v1 v2c
ESC [g n1 n2 m
ESC [p n1 n2
ESC ]
ESC_ n
ESC- n
ESC d n m
ESC j
ESC r n
ESC * m
Set page length in inches
Select Tab horizontally
Select bold
Cancel bold
Select double-strike mode
Cancel double-strike mode
Select printing mode
Perform n/180″or n/216″single line feed
Normal density graphics
Dual-Density Bit Image Graphics (Half Speed)
Select bottom margin
Cancel bottom margin
Set proportional intercharacter
Offline
Clear tab
Select superscript/subscript
Cancel superscript/subscript
Select bidirectional printing on/off
Select double-wide printing mode(continuous)
Set left and right margin
Select double -density graphics
Select fourfold -density graphics
Select line
Select printing mode
Select font and pitch
Set initialization condition
Set code page
Set vertical unit
Select printing quality
Set barcode parameters
Select high-density graphics printing
Set barcode data
Feed paper in reverse direction
Print upper-line
Print underline
Move the current printing position
Stop printing
Select printing colour
Select graphic mode
If you need more details regarding the emulation commands, please contact us.
85
Tally Dascom 1325
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
a.
This device may not cause harmful interference.
b. This device must accept any interference received, including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

Re-orientate or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.
Consult the dealer or an experienced radio/TV technician for help.
86
DASCOM REPRESENTATIVES
GERMANY
UNITED KINGDOM
RUSSIA and CIS
DASCOM Europe GmbH
DASCOM GB Ltd
DASCOM Europe GmbH
Heuweg 3
ViewPoint, Basing View,
Representation Moscow
D-89079 Ulm
Basingstoke, Hampshire
Leninsky Prospekt 95a, Office 322
Deutschland
RG21 4RG, England
119313 Moscow, Russian Federation
Tel.: +49 (0) 731 2075 0
Phone: +44 (0) 1256 481481
Phone: +7 (495) 984 70 65
Fax: +49 (0) 731 2075 100
Fax: +44 (0) 1256 481400
Fax: +7 (495) 984 56 42
www.dascom.com
www.dascom.com
www.dascom.com
SINGAPORE (ASIA PACIFIC)
AMERICAS
DASCOM AP Pte Ltd
DASCOM Americas Corporation
63 Hillview Avenue
421 W. Main Street, Waynesboro,
#08-22, Lam Soon Industrial Building
VA 22980, USA
Singapore 669569
Phone:+1 (877) 434 13 77
Phone: +65 6760 8833
www.dascom.com
Fax: +65 6760 1066
www.dascom.com.sg
FRANCE
CEE
DASCOM Europe GmbH
DASCOM Europe GmbH
117 Avenue Victor Hugo
Europaring F15 301
92100 Boulogne-Billancourt
2345 Brunn a. G.
France
Austria
Phone: +33 (1) 73 02 51 98
Phone: +43 (1) 236 01 70 10
www.dascom.com
www.dascom.com
“All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part
or in any different form requires our explicit approval. We reserve the right to make changes to this manual
without notice. All care has been taken to ensure accuracy of information contained in this manual. However,
we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information
herein.”
© 2011 DASCOM
Part No: 21.511.802.0042

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : DYAPP
Create Date                     : 2011:07:03 22:14:57+08:00
Modify Date                     : 2011:07:03 22:14:57+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - 1325 UG 2011-07-03.doc
Creator                         : DYAPP
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:57cd4b0c-aed0-49e2-901b-7c43ccbf83ca
Instance ID                     : uuid:91d54f42-41f7-4d59-9f9c-401819a92173
Page Count                      : 102
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ZIOTD13250

Navigation menu