DataRemote CDS-9070 LTE Cellular Router User Manual CDS9070

V1.0

The page 1 of 76

Revision Time: 2016-10-13

POTS in a BOXTM CDS-9070

LTE VoIP Dual Band Wi-Fi Router

User Manual V1.0

V1.0

The page 2 of 76

Revision Time: 2016-10-13

Table of Contents

1 Preface .......................................................................................................................................................................................................................................................................................................... 5

2 LED Indicators and Connectors ................................................................................................................................................................................................................................................................... 6

2.1 LED Indicators ............................................................................................................................................................................................................................................................................. 6

DC ................................................................................................................................................................................................................................................................................................................. 7

Connector for a power adapter. .................................................................................................................................................................................................................................................................. 7

WAN ............................................................................................................................................................................................................................................................................................................. 7

Connector for accessing the Internet.......................................................................................................................................................................................................................................................... 7

LAN1/2/3/4 ................................................................................................................................................................................................................................................................................................. 7

Connectors for local networked devices..................................................................................................................................................................................................................................................... 7

2.2 Hardware Installation ................................................................................................................................................................................................................................................................... 8

3 Interactive Voice Response .......................................................................................................................................................................................................................................................................... 9

4 Configuring Basic Settings ........................................................................................................................................................................................................................................................................ 12

4.1 Administrator Management ....................................................................................................................................................................................................................................................... 12

4.2 Accessing Web Page .................................................................................................................................................................................................................................................................. 13

4.2.1 From LAN port .................................................................................................................................................................................................................................................................. 13

4.2.2 From WAN port.................................................................................................................................................................................................................................................................. 13

4.3 Webpage ..................................................................................................................................................................................................................................................................................... 15

4.4 Setting up the Time Zone ........................................................................................................................................................................................................................................................... 16

4.5 Setting up the Internet/WAN Connection................................................................................................................................................................................................................................... 16

4.5.1 Static IP .............................................................................................................................................................................................................................................................................. 16

4.5.2 DHCP ................................................................................................................................................................................................................................................................................. 18

4.5.3 PPPoE ................................................................................................................................................................................................................................................................................ 18

4.6 Setting up the Internet/LTE Connection ..................................................................................................................................................................................................................................... 20

4.6.1 LTE ..................................................................................................................................................................................................................................................................................... 20

4.7 Setting up the Wireless Connection ........................................................................................................................................................................................................................................... 22

4.7.1 Enable Wireless and Setting SSID ..................................................................................................................................................................................................................................... 22

4.7.2 Encryption .......................................................................................................................................................................................................................................................................... 24

4.8 Setting up WAN Failover ........................................................................................................................................................................................................................................................... 26

4.8.1 WAN Failover List ............................................................................................................................................................................................................................................................. 26

4.8.2 Connection Manager .......................................................................................................................................................................................................................................................... 27

4.9 Register ...................................................................................................................................................................................................................................................................................... 28

4.9.1 Get the Accounts ................................................................................................................................................................................................................................................................ 28

4.9.2 Connections ........................................................................................................................................................................................................................................................................ 28

4.9.3 Configuration SIP from Webpage ...................................................................................................................................................................................................................................... 28

4.9.4 View the Register Status .................................................................................................................................................................................................................................................... 29

4.10 Make Call ................................................................................................................................................................................................................................................................................... 30

4.10.1 Calling phone or extension numbers .................................................................................................................................................................................................................................. 30

4.10.2 Direct IP calls ..................................................................................................................................................................................................................................................................... 30

V1.0

The page 3 of 76

Revision Time: 2016-10-13

4.10.3 Call Hold ............................................................................................................................................................................................................................................................................ 31

4.10.4 Blind Transfer .................................................................................................................................................................................................................................................................... 31

4.10.5 Attended Transfer ............................................................................................................................................................................................................................................................... 31

4.10.6 Conference ......................................................................................................................................................................................................................................................................... 31

5 Web Configuration ..................................................................................................................................................................................................................................................................................... 32

5.1 Login .......................................................................................................................................................................................................................................................................................... 32

5.2 Status .......................................................................................................................................................................................................................................................................................... 33

5.3 Network ...................................................................................................................................................................................................................................................................................... 34

5.3.1 WAN .................................................................................................................................................................................................................................................................................. 34

5.3.2 LAN ................................................................................................................................................................................................................................................................................... 37

5.3.3 VPN/L2TP ......................................................................................................................................................................................................................................................................... 38

5.3.4 DMZ/Port Forward ............................................................................................................................................................................................................................................................ 42

5.3.5 DDNS ................................................................................................................................................................................................................................................................................. 44

5.3.6 QoS .................................................................................................................................................................................................................................................................................... 44

5.3.7 MAC Clone ........................................................................................................................................................................................................................................................................ 46

5.3.8 Routing ............................................................................................................................................................................................................................................................................... 47

5.4 Wireless ...................................................................................................................................................................................................................................................................................... 48

5.4.1 Basic ................................................................................................................................................................................................................................................................................... 48

5.4.2 Security .............................................................................................................................................................................................................................................................................. 50

5.4.3 WPS ................................................................................................................................................................................................................................................................................... 51

5.4.4 Station list .......................................................................................................................................................................................................................................................................... 53

5.4.5 Client .................................................................................................................................................................................................................................................................................. 53

5.5 Phone.......................................................................................................................................................................................................................................................................................... 55

5.5.1 VoIP QoS ............................................................................................................................................................................................................................................................................ 55

5.5.2 Dial Plan ............................................................................................................................................................................................................................................................................. 55

5.5.3 Blacklist ............................................................................................................................................................................................................................................................................. 56

5.5.4 Call Log ............................................................................................................................................................................................................................................................................. 56

5.6 SIP Account ................................................................................................................................................................................................................................................................................ 57

5.6.1 FXS1/2 SIP Account .......................................................................................................................................................................................................................................................... 57

5.6.2 FXS1/2 Audio Configuration ............................................................................................................................................................................................................................................. 57

5.6.3 FXS1/2 Supplementary Service Subscription .................................................................................................................................................................................................................... 59

5.7 Security ...................................................................................................................................................................................................................................................................................... 60

5.7.1 Filtering Setting .................................................................................................................................................................................................................................................................. 60

5.7.2 Content Filtering ................................................................................................................................................................................................................................................................ 61

5.8 Application ................................................................................................................................................................................................................................................................................. 63

5.8.1 Advance Nat ....................................................................................................................................................................................................................................................................... 63

5.8.2 UPnP .................................................................................................................................................................................................................................................................................. 64

5.8.3 IGMP .................................................................................................................................................................................................................................................................................. 64

5.9 Administration ........................................................................................................................................................................................................................................................................... 65

5.9.1 Management ....................................................................................................................................................................................................................................................................... 65

5.9.2 Firmware Upgrade ............................................................................................................................................................................................................................................................. 67

5.9.3 Scheduled Tasks ................................................................................................................................................................................................................................................................. 68

5.9.4 Provision ............................................................................................................................................................................................................................................................................ 69

V1.0

The page 4 of 76

Revision Time: 2016-10-13

5.9.5 TR069 ................................................................................................................................................................................................................................................................................ 70

5.10 System Log ................................................................................................................................................................................................................................................................................ 71

5.10.1 Logout ................................................................................................................................................................................................................................................................................ 72

5.10.2 Reboot ................................................................................................................................................................................................................................................................................ 72

6 Trouble shooting of the guide .................................................................................................................................................................................................................................................................... 73

6.1 Setting your PC gets IP automatically ........................................................................................................................................................................................................................................ 73

6.2 Can not connect to the configuration Website ............................................................................................................................................................................................................................ 74

6.3 Forget the Password ................................................................................................................................................................................................................................................................... 74

7 Statement ................................................................................................................................................................................................................................................................................................... 75

V1.0

The page 5 of 76

Revision Time: 2016-10-13

1 Preface

Thank you for choosing CDS-9070 wireless router with VoIP. This product will allow you to make ATA call using your broadband connection,

and provides Wi-Fi router function.

This manual provides basic information on how to install and connect CDS-9070 wireless router with VoIP to the Internet. It also includes

features and functions of LTE connection, wireless router with VoIP components, and how to use it correctly.

Before you can connect CDS-9070 to the Internet and use it, you must have a high-speed broadband connection installed. A high-speed

connection includes environments such as DSL, LTE wireless network, cable modem, and a leased line.

CDS-9070 wireless router with VoIP is a stand-alone device, which requires no PC to make Internet calls. This product guarantees clear and

reliable voice quality on Internet, which is fully compatible with SIP industry standard and able to interoperate with many other SIP devices

and software on the market.

V1.0

The page 6 of 76

Revision Time: 2016-10-13

2 LED Indicators and Connectors

Before you use the high speed router, please get acquainted with the LED indicators and connectors first.

2.1 LED Indicators

Front Panel

LED

Status

Explanation

PWR

On (GREEN)

The router is powered on (External Power) and running normally.

On Blinking (GREEN)

The router is powered on (Internal Power - BAT) and running

normally.

OFF

The router is powered off.

SYS

On (GREEN)

System OK

On (RED)

System Fault (SW or HW)

BATTERY

On (GREEN)

Battery Charged

On Blinking (GREEN)

Battery Charging

Red

Battery Low or not connected

Phone 1/2

On (GREEN)

Registered

OFF

Not Registered

WPS

OFF

Not Registered

On (GREEN)

Active for Key registration

WLAN Client

OFF

Non active for Key registration

On (GREEN)

Wireless Client Connected

On Blinking (GREEN)

Wireless traffic (Data)

WLAN AP

OFF

The Wireless Client is powered off or not connected

On (GREEN)

Wireless AP ready

On Blinking (GREEN)

Wireless traffic (Data)

WAN ETH

OFF

The Wireless AP is powered off

On (GREEN)

Connected (Registered)

On Blinking (GREEN)

Connected (Data)

LTE SVC

OFF

Disconnected

On (GREEN)

Connected (Registered)

On Blinking (GREEN)

Connected (Data)

RSSI

OFF

Disconnected

On (GREEN)

Strong

V1.0

The page 7 of 76

Revision Time: 2016-10-13

On Blinking (GREEN)

Medium

CELL DCD

On (RED)

Weak

On (GREEN)

LTE

On Blinking (GREEN)

3G

SIM

Off

No Service

On (GREEN)

SIM Accepted

Rear Panel

Interface

Description

DC

Connector for a power adapter.

WAN

Connector for accessing the Internet.

LAN1/2/3/4

Connectors for local networked devices.

V1.0

The page 8 of 76

Revision Time: 2016-10-13

2.2 Hardware Installation

Before starting to configure the router, you have to connect your devices correctly.

Step 1.Connect Line port to land line jack with a RJ-11 cable.

Step 2.Connect the WAN port to a modem or switch or router or Internet with an Ethernet cable.

Step 3.Connect one port of 4 LAN ports to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly.

Step 4.Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity.

Step 5.Check the Power and WAN, LAN LEDs to assure network connections.

V1.0

The page 9 of 76

Revision Time: 2016-10-13

3 Interactive Voice Response

In any circumstance, pressing the following command to enter relevant function. The following table lists command, and description.

Voice Menu Setting Options

Operation code

Contents

1

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “1”, and CDS-9070 report the current WAN port connection type

Step 3.Prompt "Please enter password”, user need to input password with end char # if user want to

configuration WAN port connection type.

 The password in IVR is same as the one of WEB login, user can use phone keypad to enter

password directly, and the matching table is in Note 4.

 For example: WEB login password is “admin”, so password in IVR is “admin” too, user input

“23646” to access and then configuration WAN connection port.

Step 4.Report “operation successful” if password is right.

Step 5.Choose the new WAN port connection type from 1.DHCP and 2.Static

Step 6.Report “operation successful”, this means user make the changes successfully, and then

CDS-9070 will return to sound prompting “please enter your option, one WAN Port ……”.

 Note: add “#” to assume after input password and selected new WAN port connection type

If you want to quit by the wayside, press “*”

2

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “2”, and CDS-9070 report current WAN Port IP Address

Step 3.Input the new WAN port IP address and with the end char #,

 using “*” to replace “.”, user can input 192*168*20*168 to set the new IP address 192.168.20.168

 press # key to indicate that you have finished

Step 4.Report “operation successful” if user operation properly.

Note: If you want to quit by the wayside, press “**”.



3

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “3”, and CDS-9070 report current WAN port subnet mask

Step 3.Input a new WAN port subnet mask and with the end char #

 using “*” to replace “.”, user can input 255*255*255*0 to set the new WAN port subnet mask

255.255.255.0

 press # key to indicate that you have finished

3) Report “operation successful” if user operation properly.

Note: If you want to quit by the wayside, press “**”.



4

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “4”, and CDS-9070 report current gateway

Step 3.Input the new gateway and with the end char #

 using “*” to replace “.”, user can input 192*168*20*1 to set the new gateway 192.168.20.1

 press # (pound) key to indicate that you have finished

3) Report “operation successful” if user operation properly.

Note: If you want to quit by the wayside, press “**”.



5

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “5”, and CDS-9070 report current DNS

Step 3.Input the new DNS and with the end char #

 using “*” to replace “.”, user can input 192*168*20*1 to set the new gateway 192.168.20.1

 press # (pound) key to indicate that you have finished

3) Report “operation successful” if user operation properly.

If you want to quit by the wayside, press “**”.



V1.0

The page 10 of 76

Revision Time: 2016-10-13

6

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “6”, and CDS-9070 report “Factory Reset”

Step 3.Prompt "Please enter password", the method of inputting password is the same as operation 1.

 If you want to quit by the wayside, press “*”.

Step 4.Prompt “operation successful” if password is right and then CDS-9070 will be factory setting.

Step 5.Press “7” reboot to make changes effective.

7

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “7”, and CDS-9070 report “Reboot”

Step 3.Prompt "Please enter password", the method of inputting password is same as operation 1.

Step 4.CDS-9070 will reboot if password is right and operation is properly.

8

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “8”, and CDS-9070 report “WAN Port Login”

Step 3.Prompt "Please enter password", the method of inputting password is same as operation 1.

 If you want to quit by the wayside, press “*”.

Step 4.Report “operation successful” if user operation properly.

Step 5.Prompt “1enable 2disable”,choose 1 or 2, and with confirm char #

Step 6.Report “operation successful” if user operation properly.

9

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “9”, and CDS-9070 report “ WEB Access Port”

Step 3.Prompt “Please enter password”, the method of inputting password is same as operation 1.

Step 4.Report “operation successful” if user operation properly.

Step 5.Report the current WEB Access Port

Step 6.Set the new WEB access port and with end char #

Step 7. Report “operation successful” if user operation properly.

0

Step 1.Pick up phone and press “****” to start IVR

Step 2.Choose “0”, and CDS-9070 report current Firmware version

V1.0

The page 11 of 76

Revision Time: 2016-10-13

Notice:

When using Voice Menu, press * (star) to return the main menu.

If any changes made in the IP assignment mode, please reboot the CDS-9070 to take the setting into effect.

When enter IP address or subnet mask, use “*”(Star) to replace “.” (Dot).

For example, to enter the IP address 192.168.20.159 by keypad, press these keys: 192*168*20*159, use the #(pound) key to indicate

that you have finished entering the IP address.

#(pound) key to indicate that you have finish entering the IP address or subnet mask

When assigning IP address in Static IP mode, setting IP address, subnet mask and default gateway is a must. If in DHCP mode, please

make sure that DHCP SERVER is available in your existing broadband connection to which WAN port of CDS-9070 is connected.

The default LAN port IP address of CDS-9070 is 192.168.1.1 and do not set the WAN port IP address of CDS-9070 in the same

network segment of LAN port of CDS-9070, otherwise it may lead to the CDS-9070 fail to work properly.

You can enter the password by phone keypad, the matching table between number and letters as follows:

 To input: D, E, F, d, e, f -- press ‘3’

 To input: G, H, I, g, h, i -- press ‘4’

 To input: J, K, L, j, k, l -- press ‘5’

 To input: M, N, O, m, n, o -- press ‘6’

 To input: P, Q, R, S, p, q, r, s -- press ‘7’

 To input: T, U, V, t, u, v -- press ‘8’

 To input: W, X, Y, Z, w, x, y, z -- press ‘9’

 To input all other characters in the administrator password-----press ‘0’,

E.g. password is ‘admin-admin’, press ‘236460263’

V1.0

The page 12 of 76

Revision Time: 2016-10-13

4 Configuring Basic Settings

4.1 Administrator Management

This chapter explains how to setup a password for an administrator user and how to adjust settings for accessing Internet successfully.

CDS-9070 supports two-level management: administrator and user. For administrator mode operation, please type “admin/Password1”

on Username/Password and click Login button to configuration.

V1.0

The page 13 of 76

Revision Time: 2016-10-13

4.2 Accessing Web Page

4.2.1 From LAN port

1. Make sure your PC have connected to the router’s LAN port correctly.

Notice: You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the

default IP address of router is 192.168.1.1. For the detailed information, please refer to the later section - Trouble shooting of the guide.

2. Open a web browser on your PC and type http://192.168.1.1. The following window will be open to ask for username and password,

and you can choose language.

3. For administrator mode operation, please type “admin/Password1” on Username/Password and click Login to configuration.

Notice: If you fail to access to the web configuration, please go to “Trouble

Shooting” for detecting and solving your problems.

4. The web page can be logged out after 5 minutes without any operation.

4.2.2 From WAN port

1. Make sure your PC can connect to the router’s WAN port correctly.

2. Getting the IP addresses of WAN port using Voice prompt.

V1.0

The page 14 of 76

Revision Time: 2016-10-13

3. Open a web browser on your PC and type http://the IP address of WAN port. The following window will be open to ask for

username and password.

4. For administrator mode operation, please type “admin/Password1” on Username/Password and click Login to configuration.

Notice: If you fail to access to the web configuration, please go to “Trouble

Shooting” for detecting and solving your problem.

5. The web page can be logged out after 5 minutes without any operation.

V1.0

The page 15 of 76

Revision Time: 2016-10-13

4.3 Webpage

No.

Name

Description

1

Navigation bar

Click navigation bar, many sub-navigation bar will

appear in the place 2

2

Title

Click sub-navigation bar to choose one

configuration page

3

Parameter

To configuration the parameters

Every time making some changes, user

should press this button to confirm the changes.

After pressing the button, the red

will appear to notice rebooting.

To cancel the changes.

Press it to reboot the router

V1.0

The page 16 of 76

Revision Time: 2016-10-13

4.4 Setting up the Time Zone

Open Administration/Management webpage as shown below, please select the Time Zone for the router installed and specify the NTP

server and set the update interval in NTP synchronization.

4.5 Setting up the Internet/WAN Connection

Open the Network/WAN webpage as shown below; please select the appropriate IP Mode according to the information from your ISP.

There are three types offered in this page, which are Static, DHCP and PPPoE.

4.5.1 Static IP

You will receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service

providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet. If you

V1.0

The page 17 of 76

Revision Time: 2016-10-13

have a public subnet, you could assign an IP address to the WAN interface.

WAN IP Mode

The mode for obtain IP address

LAN Connection

Mode

Select to NAT or Bridge

IP Address

Type the IP address

Subnet Mask

Type the subnet mask

Default Gateway

Type the gateway IP address

DNS Mode

Set the DNS Mode from Auto and Manual,

If user choose manual, you should fill the

primary DNS address and Secondary DNS

address into Primary DNS Address and

Secondary DNS Address.

Primary DNS

Server

Type in the primary IP address for the route

Secondary DNS

Server

Type in secondary IP address for necessity in

the future

V1.0

The page 18 of 76

Revision Time: 2016-10-13

4.5.2 DHCP

It is not necessary for you to type any IP address manually. Simply choose this type and the system will obtain the IP address automatically

from DHCP server.

WAN IP Mode

The mode for obtain IP address

LAN Connection

Mode

Select to NAT or Bridge

DNS Mode

Set the DNS Mode from Auto and Manual,

If user choose manual, you should fill the

primary DNS address and Secondary DNS

address into Primary DNS Address and

Secondary DNS Address.

Primary DNS

Server

Type in the primary IP address for the route

Secondary DNS

Server

Type in secondary IP address for necessity in

the future

4.5.3 PPPoE

PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted standards: PPP and Ethernet. It connects users

through an Ethernet to the Internet with a common broadband medium, such as a single DSL line, wireless device or cable modem. All the

users over the Ethernet can share a common connection.

PPPoE is used for most of DSL modem users. All local users can share one PPPoE connection for accessing the Internet. Your service

provider will provide you information about user name, password, and authentication mode.

V1.0

The page 19 of 76

Revision Time: 2016-10-13

WAN IP

Mode

The mode for obtain IP address

LAN

Connection

Mode

Select to NAT or Bridge

DNS Mode

Set the DNS Mode from Auto and Manual,

If user choose manual, you should fill the primary DNS

address and Secondary DNS address into Primary DNS

Address and Secondary DNS Address.

Primary DNS

Server

Type in the primary IP address for the route

Secondary

DNS Server

Type in secondary IP address for necessity in the future

PPPoE

Account

Assign a specific valid user name provided by the ISP

PPPoE

Password

Assign a valid password provided by the ISP

Confirm

Password

Input the password again

Service Name

The destination of PPPoE server, Leave empty to auto

detect.

Operation

Mode

Select to Keep Alive, On Demand or Manual

Keep Alive

Redial

Period(0-3600

s)

The interval time for redialing up

V1.0

The page 20 of 76

Revision Time: 2016-10-13

4.6 Setting up the Internet/LTE Connection

4.6.1 LTE

LTE Modem

Enable

Select to Disable, Auto Connect and

Always Connect.

GSM Call

Enable

Enable GSM voice call

4G

Connection

Type

4G connection type ,auto or manual

APN

Access Point Name

Dial Number

LTE connection dial number

Username

Auth username

Password

Auth password

Internet

Connection

Here you can choose use 3G, 4G or

auto mode

Lock Cell

Lock cell function

Status

PIN code bind status

SIM bind

Input the SIM bind code

The remaining

number of

unlock

Warning of the operation error time,

should less than 3

V1.0

The page 21 of 76

Revision Time: 2016-10-13

When LTE connected successfully, return the Status page, you can check the link status and the IP address obtained from the ISP.

V1.0

The page 22 of 76

Revision Time: 2016-10-13

4.7 Setting up the Wireless Connection

To set up the wireless connection, please skip the following steps.

4.7.1 Enable Wireless and Setting SSID

Open 2.4G (5G) /Basic webpage as shown below

Radio On/Off

Select to enable or disable wireless.

Wireless

Connection

Mode

Select to AP or Client. WiFi Client

would be option for Active WAN.

Network Mode

Choose one network mode from the

drop down list.

Multiple SSSD

Set more wireless network.

Broadcast(SSID

)

Broadcast or hide the SSID

AP Isolation

prevents one wireless client

communicating with another wireless

client.

MBSSID AP

Isolation

Other clients outside the AP can not

access the clients under this AP

BSSID

A group of wireless workstations and

a wireless local area network access

V1.0

The page 23 of 76

Revision Time: 2016-10-13

point (AP) form a basic access device

(BSS), each computer in the BSS

must be configured with the same

BSSID.

Frequency

Choose channel frequency.

HT Physical

Mode

In HT (High Throughput) Physical

mode setting allow for control of the

802.11n wireless environment.

Operating

Mode

Mixed Mode: In this mode packets

are transmitted with a preamble

compatible with the legacy

802.11a/g, the rest of the packet has a

new format.

Green Field: In this mode high

throughput packets are transmitted

without a legacy compatible part.

Channel

BandWidth

20 Channel Width = 20 MHz

20/40 Channel Width = 20/40 MHz

Extension

Channel(5GHz

Only)

Auto to choose extension channel

frequency.

VHT

Option(5GHz

Only)

With IEEE 802.11ac

standard, very-high-throughput can

be configured to operate on the 5

GHz frequency band.

VHT

BandWidth(5G

Hz Only)

20/40 Channel Width = 20/40 MHz

80 Channel Width = 80 MHz

V1.0

The page 24 of 76

Revision Time: 2016-10-13

4.7.2 Encryption

Open 2.4G (5G)/Security webpage to set the encryption of routers.

WAP-PSK/WAP2-PSK/WAPPSKWAP2PSK

SSID Choice

Choose one SSID from Off-premises

1, off-premises 2 and Premises.

Security Mode

Unless one of these encryption

modes is selected, wireless

transmissions to and from your

wireless network can be easily

intercepted and interpreted by

unauthorized users.

WPA

Algorithms

TKIP (Temporal Key Integrity

Protocol) provides per-packet key

generation and is based on WEP.

AES (Advanced Encryption

Standard) is a very secure block

based encryption. With the "TKIP

and AES" option, the router

negotiates the cipher type with the

client, and uses AES when available.

Pass Phrase

Security password

Key Renewal

Interval

The amount of time before the group

key used for broadcast and multicast

data is changed.

Default Key

Select one of the four WEP keys, the

key settings on the client network

V1.0

The page 25 of 76

Revision Time: 2016-10-13

OPENWEP

card also need to correspond to this.

WEP Keys

Set the WEP key. Select 64-bit key to

enter Hex is 10 characters, or ASCII

code is 5characters; select 128-bit

keys need to enter Hex is 26

characters, or ASCII is 13characters.

Policy

Select to Disable/Allow/Reject

Add a station

MAC

Use this section to add MAC

addresses to the list below.

V1.0

The page 26 of 76

Revision Time: 2016-10-13

4.8 Setting up WAN Failover

4.8.1 WAN Failover List

WAN Failover works in multiple outbound links to assure that you maintain Internet connectivity if a loss of connectivity occurs on one of

your WAN connections. If one of your ISP links goes down, WAN Failover will automatically route all traffic over the other WAN(s) until

service is restored.

CDS-9070 allows failover of the default route to WAN

interfaces. This part of settings allows ranking each WAN

interface in order of preferred usage for the default route.

The default route will always be set to the highest-priority

connected WAN interface. The assignment changes as

WAN interfaces connect or disconnect from the current

network.

Default Route Selection support WAN/ WiFi 2.4G/ LTE

and WiFi 5.0G. WAN Failover list switch over from

Number1 (highest priority) to Number 4 (lowest priority).

V1.0

The page 27 of 76

Revision Time: 2016-10-13

4.8.2 Connection Manager

Enable

Enable this function, WAN Failover is

based on ping result. Disable this

function, WAN Failover is based on

each interface physical status.

Detect

Interval

Interval time for detecting WAN

connection.

Ping this

WAN’s

Gateway

Ping the IP address of WAN’s gateway.

Ping this IP

The IP address for ping detection

Force WAN

Failover

Enable to setup the re-try times for ping

Max Try

Times for

Ping

Setup the re-try times for ping

V1.0

The page 28 of 76

Revision Time: 2016-10-13

4.9 Register

4.9.1 Get the Accounts

CDS-9070 have 2 phone ports, you can use it to make SIP call, and before registering, you should get the SIP account from you administrator

or provider.

4.9.2 Connections

Connect CDS-9070 to the Internet properly

4.9.3 Configuration SIP from Webpage

Step 1.Open SIP Account/Line 1 webpage, as the picture in the right side.

Step 2. Fill account which get from you administrator into Display Name parameter, Phone Number parameter, and Account parameter.

Step 3.Fill password which get from you administrator into Password parameter.

Step 4.Press button in the bottom of the webpage to save changes.

Note: Please REBOOT to make the changes effective! please press Reboot button to make changes effective. if there is

V1.0

The page 29 of 76

Revision Time: 2016-10-13

4.9.4 View the Register Status

To view the status, please open Status webpage and view the value of register status. The value is registered like the following picture which

means CDS-9070 have registered normally and you can make calls.

V1.0

The page 30 of 76

Revision Time: 2016-10-13

4.10 Make Call

4.10.1 Calling phone or extension numbers

To make a phone or extension number call:

a) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) have public IP addresses, or

b) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) are on the same LAN using private or public IP addresses, or

c) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) can be connected through a router using public or private IP

addresses.

To make a call, first pick up the analog phone or turn on the speakerphone on the analog phone, input the IP address directly, end with #.

4.10.2 Direct IP calls

Direct IP calling allows two phones, that is, an ATA with an analog phone and another VoIP Device, to talk to each other without a SIP proxy. VoIP

calls can be made between two phones if:

a) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) have public IP addresses, or

b) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) are on the same LAN using private or public IP addresses, or

c) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) can be connected through a router using public or private IP

addresses.

To make a direct IP call, first pick up the analog phone or turn on the speakerphone on the analog phone, Input the IP address directly, with the end

“#”.

V1.0

The page 31 of 76

Revision Time: 2016-10-13

4.10.3 Call Hold

While in conversation, pressing the “*77” to put the remote end on hold, then you will hear the dial tone and the remote party will hear hold tone at

the same time.

Pressing the “*77” again to release the previously hold state and resume the bi-directional media.

4.10.4 Blind Transfer

Assuming that call party A and party B are in conversation. A wants to Blind Transfer B to C:

Step 1.Party A dials “*78” to get a dial tone, then dials party C’s number, and then press immediately key # (or wait for 4 seconds) to dial out.

Step 2.A can hang up.

4.10.5 Attended Transfer

Assuming that call party A and B are in conversation. A wants to Attend Transfer B to C:

Step 1.Party A dial “*77” to hold the party B, when hear the dial tone, A dial C’s number, then party A and party C are in conversation.

Step 2.Party A dial “*78” to transfer to C, then B and C now in conversation.

Step 3.If the transfer doesn’t success, then A and B in conversation again.

4.10.6 Conference

Assuming that call party A and B are in conversation. A wants to add C to the conference:

Step 1.Party A dial “*77” to hold the party B, when hear the dial tone, A dial C’s number, then party A and party C are in conversation.

Step 2.Party A dial “*88” to add C, then A, B and C now in conference.

V1.0

The page 32 of 76

Revision Time: 2016-10-13

5 Web Configuration

This chapter will guide users to execute full configuration through admin mode operation.

5.1 Login

Step 1.Connect the LAN port of the router to your PC

Step 2.Open a web browser on your PC and type in http://192.168.1.1. The window will ask for typing username and password. And you

can choose language, too.

When login successfully, the

webpage shows the basic

information about the router, such

as the current WAN IP, DNS server

IP, WAN port connection mode,

WAN link status, wireless SSID,

wireless channel and F/W version

Step 3.Please type “admin/Password1” on Username/Password for administration operation. Now, the Main Screen will appear like below.

V1.0

The page 33 of 76

Revision Time: 2016-10-13

5.2 Status

This webpage shows the status information about

product information, Network and system.

It shows the basic information of the product, such as

product name, serial number, MAC address, hardware

version and software version.

It also shows the information of Link Status, WAN Port

Status, and LAN Port Status.

And it shows the current time and the running time of

the product.

The picture in the right side is the CDS-9070’s Status

webpage.

V1.0

The page 34 of 76

Revision Time: 2016-10-13

5.3 Network

You can configuration the WAN port, LAN port, DDNS, Multi WAN,DMZ, MAC Clone,Port Forward and so on in these two bars.

5.3.1 WAN

This page allows you to set WAN configuration with different modes. Use the Connection Type drop down list to choose one WAN mode and then

the corresponding page will be displayed.

Static IP:

You will receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service

providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet. If you

have a public subnet, you could assign an IP address to the WAN interface.

WAN IP Mode

The mode for obtain IP address

LAN Connection

Mode

Select to NAT or Bridge

IP Address

Type the IP address

Subnet Mask

Type the subnet mask

Default Gateway

Type the gateway IP address

DNS Mode

Set the DNS Mode from Auto and Manual

Primary DNS

Server

Type in the primary IP address for the route

Secondary DNS

Server

Type in secondary IP address for necessity in

the future

V1.0

The page 35 of 76

Revision Time: 2016-10-13

DHCP:

It is not necessary for you to type any IP address manually. Simply choose this type and the system will obtain the IP address automatically

from DHCP server.

WAN IP Mode

The mode for obtain IP address

LAN Connection

Mode

Select to NAT or Bridge

DNS Mode

Set the DNS Mode from Auto and Manual,

If user choose manual, you should fill the

primary DNS address and Secondary DNS

address into Primary DNS Address and

Secondary DNS Address.

Primary DNS

Server

Type in the primary IP address for the route

Secondary DNS

Server

Type in secondary IP address for necessity in

the future

PPPoE:

PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted standards: PPP and Ethernet. It connects users

through an Ethernet to the Internet with a common broadband medium, such as a single DSL line, wireless device or cable modem. All the

users over the Ethernet can share a common connection.

PPPoE is used for most of DSL modem users. All local users can share one PPPoE connection for accessing the Internet. Your service

provider will provide you information about user name, password, and authentication mode.

V1.0

The page 36 of 76

Revision Time: 2016-10-13

WAN IP

Mode

The mode for obtain IP address

LAN

Connection

Mode

Select to NAT or Bridge

DNS Mode

Set the DNS Mode from Auto and Manual,

If user choose manual, you should fill the primary DNS

address and Secondary DNS address into Primary DNS

Address and Secondary DNS Address.

Primary DNS

Server

Type in the primary IP address for the route

Secondary

DNS Server

Type in secondary IP address for necessity in the future

PPPoE

Account

Assign a specific valid user name provided by the ISP

PPPoE

Password

Assign a valid password provided by the ISP

Confirm

Password

Input the password again

Service Name

The destination of PPPoE server, Leave empty to auto

detect.

Operation

Mode

Select to Keep Alive, On Demand or Manual

Keep Alive

Redial

Period(0-3600

s)

The interval time for redialing up

V1.0

The page 37 of 76

Revision Time: 2016-10-13

5.3.2 LAN

LAN Port:

The most generic function of router is NAT. What NAT does is to translate the packets from public IP address to local IP address to forward the right

packets to the right host and vice versa.

Local IP Address

Type in local IP address for connecting

to a local private network

Local Subnet Mask

Type in an address code that

determines the size of the network.

Local DHCP Server

If or not enable DHCP server.

DHCP Starting

Address

Enter a value of the IP address pool for

the DHCP server to start with when

issuing IP addresses.

DHCP Ending Address

Enter a value of the IP address pool for

the DHCP server to end with when

issuing IP addresses.

DNS Mode

Set the DNS Mode from Auto and

Manual.

Primary/Secondary

DNS

Input the primary or secondary DNS IP

address.

Client Lease Time

It allows you to set the leased time for

the specified PC.

DHCP Client List

Check which LAN devices are

currently leasing IP addresses.

DHCP Static Allotment

Specify to reserve DHCP addresses.

DNS Proxy

allows clients to use a device as a DNS

proxy server

V1.0

The page 38 of 76

Revision Time: 2016-10-13

5.3.3 VPN/L2TP

VPDN

VPN Enable

Enable PPTP or L2TP VPN Client

Initial Service IP

VPN server IP address

User Name

The account for authentication

Password

The password for authentication

VPN As Default Route

The remote virtual IP as default

gateway .

MPPE Stateful(PPTP

Only)

Stateless encryption provides a lower

level of performance, but will be more

reliable in a lossy network

environment.

Require MPPE(PPTP

Only)

enable MPPE (Microsoft

Point-to-Point Encryption). It’s a

protocol for encrypting data across

PPP and VPN links.

L2TP Tunnel Name

Enter L2TP Tunnel Name.

L2TP Tunnel Password

Enter L2TP tunnel password in this

item.

V1.0

The page 39 of 76

Revision Time: 2016-10-13

L2TP Server

L2TP Server Enable

Select to enable L2TP server.

Local IP Address

Set the IP address of L2TP server.

Pool Start Address

Set the IP pool start IP address which

will assign to the L2TP clients.

Pool End Address

Set the IP pool end IP address which

will assign to the L2TP clients.

Max MTU

Maximum Transmission Unit. It is the

identifier of the maximum size of

packet, which is possible to transfer in

a given environment.

Max MRU

Maximum Receiving Unit. It is the

identifier of the maximum size of

packet, which is possible to receive in

a given environment.

User Name

Set the username which will assign to

L2TP client.

Password

Set the password which will assign to

L2TP client.

V1.0

The page 40 of 76

Revision Time: 2016-10-13

IPsec Connection

IPSec Connection List

The connection status of IPSec VPN

IPSec Connection

Select the specify VPN

Connection Name

The name of this IPSec VPN

IPSec Enable

Select to enable or disable IPSec VPN

Interface

Select the interface for encryption

IPSec Networking Type

The connection type of networking

Authentication Type

The authentication method of IPSec

VPN

PSK

The secret of IPSec VPN

Local ID Type

Select the local ID type for IKE

negotiation

Local WANs IP

Address/FQDN

Local IP address or domain name for

IKE negotiation

Remote ID Type

Select the remote ID type for IKE

negotiation

Remote WANs IP

Address/FQDN

the address of remote side IPSec VPN

server

Local LAN IP Address/

Subnet Mask Length

IPSec local protected subnet’s address.

Remote LAN IP

Address/ Subnet Mask

Length

IPSec remote protected subnet’s

address.

Policy Protocol

The policy protocol for encryption

V1.0

The page 41 of 76

Revision Time: 2016-10-13

Encapsulated Mode

Select the security protocols

NAT Enable

Enable NAT Traversal for IPSec. This

item must be enabled when router

under NAT environment.

Mode

Select from “Main” and “aggressive”

for the IKE negotiation mode in phase

1.

Encryption Algorithm

Select Encryption Algorithm to be

used in IKE negotiation.

Integrity Algorithm

Select Integrity Algorithm to be used

in IKE negotiation.

Diffie-Hellman (DH)

Group

Select Diffie-Hellman Group to be

used in key negotiation phase 1.

SA Lifetime of Phase 1

Set the lifetime in IKE negotiation.

DPD Time Interval(s)

Set the interval after which DPD is

triggered if no IPSec protected packets

is received from the peer.

DPD Timeout(s)

Set the timeout of DPD packets.

Encryption Algorithm

Select Encryption Algorithm to be

used in IPSec SA negotiation.

Integrity Algorithm

Select Integrity Algorithm to be used

in IPSec SA negotiation.

SA Lifetime of Phase 2

Set the lifetime in IPSec SA

negotiation

PFS

Enable or disable PFS. (Perfect

Forward Secrecy)PFS will ensure the

same key will not be generated again

V1.0

The page 42 of 76

Revision Time: 2016-10-13

5.3.4 DMZ/Port Forward

DMZ

DMZ Enable

If or not enable DMZ.

DMZ Host IP Address

Enter the private IP address of the

DMZ host

Get Current PC IP

Get the current PC’s IP address

automatically, this IP address would be

used as DMZ host.

V1.0

The page 43 of 76

Revision Time: 2016-10-13

Port Forward

Port Forwarding

Comment

Assign a meaningful name for port

forwarding.

IP Address

The IP address in LAN side

Port Range

The port range for LAN host, from 1 to

65535

Protocol

Select from “TCP”, “UDP” or

“TCP&UDP”

Virtual Servers

Comment

Assign a meaningful name to the

virtual server.

IP Address

The IP address of the system on your

internal network that will provide the

virtual service.

Public Port

The port that will be accessed from the

Internet.

Private Port

The port that will be used on your

internal network.

Protocol

Select from “TCP”, “UDP” or

“TCP&UDP”

Friendly IP

The IP address allow to access from

WAN side.

IP Address

The IP address of friendly IP

V1.0

The page 44 of 76

Revision Time: 2016-10-13

5.3.5 DDNS

Dynamic DNS Provider

Select the DDNS service which you

have established an account with.

Account

Enter account that DDNS server

provided.

Password

Enter password that DDNS server

provided.

DDNS URL

Enter the DDNS Domain name or IP

address.

Status

Show current status of DDNS

5.3.6 QoS

QoS Enable

Select to enable QoS function

Upstream

Prescribe uplink speed of router.

Downstream

Prescribe downlink speed of router.

Name

Set server name of the service that you

want to set it with QoS Control.

Source IP Address

Enter source IP address of the user (for

example, PC) who you want to set it

with QoS Control.

Dest IP Address

Enter destination IP address of the user

(for example, PC) who you want to set

it with QoS Control.

Protocol

Select from TCP /UDP /ICMP

V1.0

The page 45 of 76

Revision Time: 2016-10-13

Src.Port Range

Source port range of the service that

you want to set it with QoS Control.

Dst.Port Range

Destination port number of the service

that you want to set it with QoS

Control.

Physical Port

Select from WAN/LAN

DSCP

set the Differentiated Services Code

Point (DSCP) values in Quality of

Service (QoS)

802.1p

802.1p is an IEEE standard that

describes mechanisms to prioritize

traffic and perform dynamic multicast

filtering.

VLAN ID

When configuring a VLAN tag-based

QoS policy map, the router applies the

policy to one Ethernet port and only to

the VLANs on that particular port.

Remark DSCP

Remark DSCP Tag

Remark 802.1p

Remark 802.1p Tag

Remark VLAN_ID

Remark VLAN_ID Tag

Priority

Select from voice (VO), video (VI),

best effort (BE), and background (BK)

Drop

Select to Drop or not drop the packet

Rate Limit

Limit the speed of this rule

V1.0

The page 46 of 76

Revision Time: 2016-10-13

5.3.7 MAC Clone

Some ISPs will require you to register your MAC address. If you do not wish to re-register your MAC address, you can have the router clone the

MAC address that is registered with your ISP. To use the Clone Address button, the computer viewing the Web-base utility screen will have the

MAC address automatically entered in the Clone WAN MAC field.

MAC Address Clone

Select to enable or disable

MAC Address

The MAC address for clone

Get Current PC MAC

clone the currently PC MAC address

to router’s Internet port automatically

V1.0

The page 47 of 76

Revision Time: 2016-10-13

5.3.8 Routing

Destination

The IP address of packets that will take

this route.

Host/Net

Select the Host or Networking

Gateway

Specifies the next hop to be taken if

this route is used.

Interface

Specifies the interface LAN/

INTERNET/ VOICE/ TR069/ VPN

Comment

Set comment of this routing.

V1.0

The page 48 of 76

Revision Time: 2016-10-13

5.4 Wireless

5.4.1 Basic

Radio On/Off

Select to enable or disable wireless.

Wireless

Connection Mode

Select to AP or Client. WiFi Client

would be option for Active WAN.

Network Mode

Choose one network mode from the

drop down list.

Multiple SSSD

Set more wireless network.

Broadcast(SSID)

Broadcast or hide the SSID

AP Isolation

Prevents one wireless client

communicating with another wireless

client.

MBSSID AP

Isolation

Other clients outside the AP can not

access the clients under this AP

BSSID

A group of wireless workstations and

a wireless local area network access

point (AP) form a basic access device

(BSS), each computer in the BSS

must be configured with the same

BSSID.

Frequency

Choose channel frequency.

HT Physical

Mode

In HT (High Throughput) Physical

mode setting allow for control of the

802.11n wireless environment.

V1.0

The page 49 of 76

Revision Time: 2016-10-13

Operating Mode

Mixed Mode: In this mode packets

are transmitted with a preamble

compatible with the legacy

802.11a/g, the rest of the packet has a

new format.

Green Field: In this mode high

throughput packets are transmitted

without a legacy compatible part.

Channel

BandWidth

20 Channel Width = 20 MHz

20/40 Channel Width = 20/40 MHz

Extension

Channel(5GHz

Only)

Auto to choose extension channel

frequency.

VHT

Option(5GHz

Only)

With IEEE 802.11ac

standard, very-high-throughput can

be configured to operate on the 5

GHz frequency band.

VHT

BandWidth(5GHz

Only)

20/40 Channel Width = 20/40 MHz

80 Channel Width = 80 MHz

V1.0

The page 50 of 76

Revision Time: 2016-10-13

5.4.2 Security

Open 2.4G (5G)/Security webpage to set the encryption of routers.

WAP-PSK/WAP2-PSK/WAPPSKWAP2PSK

SSID Choice

Choose one SSID from Off-premises

1, off-premises 2 and Premises.

Security Mode

Unless one of these encryption

modes is selected, wireless

transmissions to and from your

wireless network can be easily

intercepted and interpreted by

unauthorized users.

WPA Algorithms

TKIP (Temporal Key Integrity

Protocol) provides per-packet key

generation and is based on WEP.

AES (Advanced Encryption

Standard) is a very secure block

based encryption. With the "TKIP

and AES" option, the router

negotiates the cipher type with the

client, and uses AES when available.

Pass Phrase

Security password

Key Renewal

Interval

The amount of time before the group

key used for broadcast and multicast

data is changed.

Default Key

Select one of the four WEP keys, the

key settings on the client network

V1.0

The page 51 of 76

Revision Time: 2016-10-13

OPENWEP

card also need to correspond to this.

WEP Keys

Set the WEP key. Select 64-bit key to

enter Hex is 10 characters, or ASCII

code is 5characters; select 128-bit

keys need to enter Hex is 26

characters, or ASCII is 13characters.

Policy

Select from Disable/Allow/Reject

Add a station

MAC

Use this section to add MAC

addresses to the list below.

5.4.3 WPS

WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection between wireless station and wireless access point (vigor

router) with the encryption of WPA and WPA2.

It is the simplest way to build connection between wireless network clients and vigor router. Users do not need to select any encryption mode and

type any long encryption passphrase to setup a wireless client every time. He/she only needs to press a button on wireless client, and WPS will

connect for client and router automatically. Press button less than 5s for 2.4G, press button between 5 to 10s for 5.0G.

V1.0

The page 52 of 76

Revision Time: 2016-10-13

WPS Config

If or not enable WPS.

WPS Summary

The status for Current connection,

SSID and so on

WPS Progress

PIN: In the following PIN options, fill

in the PIN code of the client (wireless

card, etc.) that needs to be accessed,

and then click Apply.

PBC: PBC mode There are two ways

to start, you can directly press the PBC

button on the hardware, or select to

PBC mode, and then click Apply.

WPS Status

There are three WPS states:

WSC: Idle state is idle

WSC: Start WSC Process Status is to

start sending messages

WSC: Success: If a client accesses an

AP, the WPS connection succeeds

V1.0

The page 53 of 76

Revision Time: 2016-10-13

5.4.4 Station list

You could monitor stations which

associated to this AP here.

5.4.5 Client

Enable WiFi Client would be one option for WAN Failover, select as the default route.

Connection Status

Current WiFi Client connect status

Connect

Select one SSID and press the button,

enter the password for the SSID.

Refresh

Refresh the SSID scan result

Add

Add one new/hidden SSID manually

V1.0

The page 54 of 76

Revision Time: 2016-10-13

V1.0

The page 55 of 76

Revision Time: 2016-10-13

5.5 Phone

5.5.1 VoIP QoS

SIP QoS(0-63)

QoS services can improve the quality of

voice applications. The default value is

46, and the range of values can be set

from 0 to 63.

RTP QoS(0-63)

Once Multi-WAN port is enabled, select

the corresponding voice PPPoE server

VID, the devices under the same VLAN

can transmit voice data.

5.5.2 Dial Plan

Dial Plan

Select to enable or disable

Unmatched Policy

Select from Accept or Reject

FXS

Select the FXS port

Digital Map

Fill in the expression of digital map,

please refer to the digital map syntax.

Action

Select the match action of the digital map,

Deny means the device will reject the

matching number dialing, and Dial Out

means the device can dial out the

matching number

V1.0

The page 56 of 76

Revision Time: 2016-10-13

5.5.3 Blacklist

You can upload or download the phone

book, blacklist.

5.5.4 Call Log

On this page, users can view replay lists

(outgoing calls), received calls, and missed

calls.

V1.0

The page 57 of 76

Revision Time: 2016-10-13

5.6 SIP Account

5.6.1 FXS1/2 SIP Account

Line Enable

Select to enable or disable Line

Outgoing Call without

Registration

Select to enable or disable this function

Display Name

The display name of this SIP number

Phone Number

The phone number provided by SIP

server

Account

The account provided by SIP server for

authentication

Password

The password provided by SIP server for

authentication

5.6.2 FXS1/2 Audio Configuration

Audio Codec Type

Select the appropriate encoding

G.723 Coding Speed

Select from 5.3kbps or 6.3kbps

Packet Cycle(ms)

Set the RTP packetization period. The

default configuration is 20ms

Silence Supp

Mute enable

Echo Cancel

Echo Cancellation is enabled by default

Auto Gain Control

Used to automatically adjust the speech

level of an audio signal to a

predetermined value.

Use First Matching

Select to enable or disable

V1.0

The page 58 of 76

Revision Time: 2016-10-13

Vocoder in 200OK SDP

Codec Priority

Select from local or remote

Packet Cycle Follows

Remote SDP

Select to enable or disable

FAX Mode

Select from T.30/ T.38/ ByPass

ByPass Attribute Value

Select from fax/modem or

X-fax/X-modem

T.38 CNG Detect

Enable

Select to enable or disable

T.38 CED Detect

Enable

Select to enable or disable

gpmd attribute Enable

Select to enable or disable

T.38 Redundancy

Select to enable or disable

Max Fax Rate

Select from 14400/ 9600/ 4800

V1.0

The page 59 of 76

Revision Time: 2016-10-13

5.6.3 FXS1/2 Supplementary Service Subscription

Call Waiting

Select to enable or disable

Hot Line

Fill in the hotline number. After the

subscriber is set up successfully, the

hotline number will be automatically

dialed immediately after off-hook

MWI Enable

Enable WMI (Message Waiting

Indication), enable this function if you

want to use voicemail

Voice Mailbox Numbers

Fill in the voicemail code provided by

your ISP

MWI Subscribe Enable

Select to enable or disable

VMWI Serv

Select to enable or disable

DND

After nable this option, any phone call

can not be dialed in, default is disable.

Speed Dial

Pre-set the phone number for Fast call

V1.0

The page 60 of 76

Revision Time: 2016-10-13

5.7 Security

5.7.1 Filtering Setting

Filtering

Select to enable or disable

Default Policy

Select from Drop or Accpet

Interface

Select from LAN or WAN

Mac address

Fill MAC address for Filtering control

Dest IP Address

Fill Destination IP address for Filtering

control

Source IP Address

Fill source IP address for Filtering control

Protocol

Select from TCP/ UDP /ICMP

Dest. Port Range

Fill Destination port range for Filtering

control

Src Port Range

Fill source port range for Filtering control

Action

Select from Accept or Drop

Comment

Fill the comment for this filtering rule

V1.0

The page 61 of 76

Revision Time: 2016-10-13

5.7.2 Content Filtering

Filtering

Select to enable or disable

Default Policy

Select from Drop or Accpet

Local File

Select the local file for upload

Current Webs URL

Filters

Existing URL filtering rules (blacklist)

Add a URL Filter

Add a URL filtering rule

URL

Fill the URL for webs filtering

Current Website Host

Filters

Existing keywords (blacklist)

Add a Host(keyword)

Filter

Add a keyword rule

Keyword

Fill the keyword for filtering

V1.0

The page 62 of 76

Revision Time: 2016-10-13

V1.0

The page 63 of 76

Revision Time: 2016-10-13

5.8 Application

5.8.1 Advance Nat

In this page, you can choose to enable /

disable FTP, SIP, H323, PPTP, L2TP,

IPSec services.

V1.0

The page 64 of 76

Revision Time: 2016-10-13

5.8.2 UPnP

UPnP (Universal Plug and Play) supports

null-setting for networking, can

automatically find a variety of networked

devices. When UPnP is enabled,

UPnP-enabled devices are allowed to

dynamically access the network, obtain IP

addresses, and transmit performance

information. If you have DHCP and DNS

servers on your network, you can

automatically obtain DHCP and DNS

services. UPnP-enabled devices can be

automatically disconnected from the

network without affecting the device or

other devices on the network.

5.8.3 IGMP

Multicast has the function of sending the

same data to multiple devices. An IP host

uses the IGMP (Internet Group

Management Protocol ) to report

multicast group memberships to send data

to neighboring routers, and the multicast

router uses IGMP to discover which hosts

belong to the same multicast group.

V1.0

The page 65 of 76

Revision Time: 2016-10-13

5.9 Administration

5.9.1 Management

Save Config File

Local File

Select the local file for configuration

Upload

Use this option to restore previously

saved router configuration settings.

Download

This option allows you to export and then

save the router's configuration to a file on

your computer. Be sure to save the

configuration before performing a

firmware upgrade.

Administrator Settings

New User Name

New user name for management

New Password

Type the password for user

Confirm Password

Type the same password again

Language

Setup the language for operation,

select from English or Spanish

Refresh Interval

The auto refresh interval for LTE

status

Management using VPN

Select to enable or disable

V1.0

The page 66 of 76

Revision Time: 2016-10-13

Remote Web Login

Allow host remote access from Active

WAN

Local Web Port

Enter the HTTP port number for

accessing from local side

Web Port

Enter the HTTP port number for

accessing from remote side

Web Idle Timeout(0

-60min)

Timeout for web idle activity

Allowed Remote

IP(IP1;IP2;...)

Allow the host with specified IP

address to access from webpage.

Time/Date Settings

NTP Enable

Select this option if you want to

synchronize the router's clock to a

Network Time Server over the

Internet.

Option 42

Obtain NTP Server via DHCP Server

Current Time

Displays the time currently maintained

by the router.

Sync with host

Synchronize with your current host's

system time

NTP Settings

Select your local time zone from pull

down menu.

Primary NTP Server

Type the primary Network Time

Server for synchronization.

Secondary NTP Server

Type the secondary Network Time

Server for synchronization.

NTP synchronization(1

-1440min)

Interval time for NTP synchronization.

V1.0

The page 67 of 76

Revision Time: 2016-10-13

Reset to Factory Default

This option restores all configuration

settings back to the settings that were in

effect at the time the router was shipped

from the factory. Any settings that have

not been saved will be lost.

5.9.2 Firmware Upgrade

Once you have a firmware update on your

computer, use this option to browse for

the file and then upload the information

into the router.

V1.0

The page 68 of 76

Revision Time: 2016-10-13

5.9.3 Scheduled Tasks

Scheduled WiFi Enable

Select to enable or disable

SSID

Choose the specified SSID for

scheduled WiFi

Scheduled Mode

Select the Schedule mode for cycle time

WiFi Work Time

Setup the working time for WiFi

broadcast

Schedule dReboot

Select to enable or disable

Scheduled Mode

Select the Schedule mode for cycle time

Time

Setup the reboot timing

Scheduled PPPOE

Select to enable or disable

Scheduled Mode

Select the Schedule mode for cycle time

Time

Setup the PPPoE connection timing

V1.0

The page 69 of 76

Revision Time: 2016-10-13

5.9.4 Provision

Please refer to the provision user manual to test provision.

Provision Enable

Select to enable or disable

Resync On Reset

Enable or disable DIV378 Resync after

rebooting

Resync Random

Delay(sec)

Setup the maximum delay for request

synchronization

Resync Periodic(sec)

If the last resynchronization is

unsuccessful, after the "Rsync Retry

Delay Error" time, after "time, the

device will retry the resynchronization

Resync Error Retry

Delay(sec)

Set the timed resynchronization

Forced Resync

Delay(sec)

If it is time to re-sync, but the device is

busy, in this case, the device will wait

for some time, the longest is "forced

resynchronization delay", the default is

14400s, time after the device will be

forced to re-sync.

Resync After Upgrade

After the resynchronization, enable or

disable the firmware update function

Resync From SIP

Select to enable or disable resync from

SIP

Option 66

Specifies the TFTP (Simple File

Transfer Protocol) server address

Option 67

Specifies the startup file name

Config File Name

Configure the file name

V1.0

The page 70 of 76

Revision Time: 2016-10-13

User Agent

The name of user agent

Profile Rule

The URL of the configuration file

Note that the specified file path is

relative to the root directory of the

TFTP server

Upgrade Enable

Select to enable or disable

Upgrade Error Retry

Delay(sec)

Interval time for retry upgrade firmware

if error happen

Upgrade Rule

The path of firmware located

5.9.5 TR069

TR069 Enable

Select to enable or disable

CWMP

Select to enable or disable

ACS URL

The URL of ACS agent

User Name

The user name of ACS agent

Password

The password of ACS agent

Periodic Inform Enable

Select to enable or disable the periodic

notification function is

Periodic Inform Interval

Setup periodic Notification Interval

User Name

User name for TR069 server connected

to DUT

Password

Password for TR069 server connected to

DUT

V1.0

The page 71 of 76

Revision Time: 2016-10-13

5.10 System Log

If you enable the system log in Status/syslog webpage, you can view the system log in this webpage.

V1.0

The page 72 of 76

Revision Time: 2016-10-13

5.10.1 Logout

Press the logout button to logout, and then the login window will appear.

5.10.2 Reboot

Press the Reboot button to reboot CDS-9070.

V1.0

The page 73 of 76

Revision Time: 2016-10-13

6 Trouble shooting of the guide

6.1 Setting your PC gets IP automatically

Following are the process of setting your PC gets IP automatically

Step 1.Click the “begin”

Select “control panel”, then double click “network connections” in the “control panel”Step 2.

Right clicks the “network connection” that your PC uses, select “attribute” and you can see the interface as picture 1:Step 3.

Step 4.Select “Internet Protocol (TCP/IP)”, click “attribute” button, and you can see the interface as following Picture 2 and you should click the “Get IP address automatically”.

Picture 1

Picture 2

V1.0

The page 74 of 76

Revision Time: 2016-10-13

6.2 Can not connect to the configuration Website

Solution:

Check if the Ethernet cable is properly connected, then

Check if the URL is right wrote, the format of URL is: http:// the IP address: 8080, 8080 must be added, then

Check if the version of IE is IE8, or use other browser such as Firefox or Mozilla, then Contact your administrator, supplier, or ITSP for more information or assistance.

6.3 Forget the Password

If user changed the password and then forgot, you can not access to the configuration website.

Solution:

To factory default: press reset button 10s.

V1.0

The page 75 of 76

Revision Time: 2016-10-13

7 Statement

FCC Interference Statement

DataRemote Incorporated. Declares that this device is in compliance with the essential requirements.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, many cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment. (Example-

use only shielded interface cables when connecting to computer or peripheral devices),

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

V1.0

The page 76 of 76

Revision Time: 2016-10-13

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator and your body.

DataRemote CDS-9070 LTE Cellular Router User Manual CDS9070

DataRemote, Inc. LTE Cellular Router CDS9070

Users Manual

Navigation menu

Namespaces

Views

Navigation