Datalogic ADC PA IEEE 802.11b/g CF WLAN Module User Manual manual 1

Download:
Mirror Download [FCC.gov]
Document ID	795998
Application ID	2WybS84ni7L/4YSlk29Wpw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.62kB (57692 bits)
Date Submitted	2007-05-23 00:00:00
Date Available	2007-05-23 00:00:00
Creation Date	2007-05-23 15:18:25
Producing Software	AFPL Ghostscript 8.54
Document Lastmod	2007-05-23 15:23:33
Document Title	manual 1
Document Creator	PDFCreator Version 0.9.2
Document Author:	Teresa

Falcon / DRCB-M1
IEEE 802.11b/g CF WLAN Module
User’s Manual
V0.1 Dec.20, 2005
Table of Contents
Chapter 1 Functional Description .......................................... 6
1.1 Features ....................................................................... 6
1.2 Integrated Radio Transceiver ....................................... 6
1.3 Receiver Path............................................................... 7
1.4 Transmitter Path ........................................................... 7
1.5 Calibration .................................................................... 7
Chapter 2 Installation Driver .................................................. 8
2.1 Driver Features ............................................................ 8
2.2 Installing the driver ....................................................... 8
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, whether electronic,
mechanical, photocopying, recording or otherwise without the prior
writing of the publisher.
Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp.
Pentium is trademark of Intel.
All copyright reserved.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is
firmware-limited to channels 1 through 11.
This device is intended only for OEM integrators under the following
conditions:
1) The transmitter module may not be co-located with any other transmitter or
antenna,
2) For all products market in US, OEM has to limit the operation channels in
CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM
shall not supply any tool or info to the end-user regarding to Regulatory
Domain change.
3) This module has been SAR evaluated inside the Portable Data Terminal,
model Falcon P40, of Datalogic Scanning Inc. and this module can be used
only with this specific product without further SAR evaluation. All other
portable applications need separate SAR re-evaluation.
As long as 3 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed (e.g. Portable Data Terminal).
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: O9NPA”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.The end user manual shall include
all required regulatory information/warning as show in this manual.
Canadian Regulatory Wireless Notice
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may
cause undesired operation of the device
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with IC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
Chapter 1 Functional Description
Thank you very much for purchasing this IEEE802.11b/g CF WLAN
Module. This product provides the easiest way to wireless networking.
This User Manual contains instructions in the operation of this product.
Please keep this manual for future reference.
1.1 Features

 Includes Encore signal processing for Industry-leading receive
sensitivity and extended range:
․ -74 dBm at 54Mbps
․ -76 dBm with external LNA

 High level of integration with direct converseon radio architecture
minimizes external circuitry, leading to lowest cost, lowest power, and
smallest footprint implementation

 Flexible support for a variety of system bus interfaces includeing: PCI,
Mini PCI, CardBus, PCMCIA/Compact Flash, and SDIO (4-wire,
1-wire, and SPI)

 Programmable data rates of 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and
54 Mbps.

 24-bit IV and 40-bit/104-bit key WEP encryption support

 System support for 128-bit AES

 IEEE802.1x support

 Dynamic Power Management under driver control

 WHQL-certified drivers for Windows® XP/Me/2000/98SE/98
operating systems

 Wi-Fi® compliant
1.2 Integrated Radio Transceiver
This CF module includes an integrated RF transceiver that has been
optimized for use in 2.4-GHz WLAN systems. It has been designed to
provide low-power, low-cost, and robust communications for applications
operating in the globally available 2.4-GHz unlicensed ISM band. With
an external transmit power amplifyier, it develops full output power per
the IEEE802.11b/g Specification.
1.3 Receiver Path
This CF module has a wide dynamic range, direct conversion receiver. It
employs high-order on-chip channel filtering to ensure reliable operation
in the noisy 2.4-GHz ISM band. The excellent noise figure of the receiver
makes an external LNA unnecessary.
Leading-edge Encore DSP technology improves the receive sensitivity
and extended range, that enables whole home coverage.
1.4 Transmitter Path
This CF module includes a linear transmitter capable of delivering up to
+6 dBm while meeting the IEEE802.11g specification. The output power
is adjustable in 0.6-dB steps, down to –15 dBm. Baseband data is
up-converted directly to the 2.4-GHz ISM band.
1.5 Calibration
This CF module enables the device to be used in high-volume
applications because calibration routines are not required during
manufacturing test. These calibration routines are performed periodically
in the course of normal radio operation.
Chapter 2 Installation Driver
This driver is porting from bcm4318 1.130.35.0 with CCX source code to
WinCE NDIS CF interface. This CF driver is workable in Intermec 751
PDA, and CN30 PDA.
2.1 Driver Features
IEEE 802.11b/g
Ad-Hoc / Infrastructure
WEP 64 / 128-bit
WPA-PSK / WPA2-PSK (by WZC / Funk Client)
WPA / WPA2 (by WZC / Func Client)
802.1x – TLS / 802.1x – PEAP (by WZC / Funk Client)
LEAP (by Funk Client)
WPA-TTLS (by Funk Client)
TKIP
AES
IEEE Power Save
IEEE 802.11d
2.2 Installing the driver
Step1. Copy the file, “bcmcf.dll”, into PDA.
Step2. Plug in BCM4318 CF card into system.
Step3. Enter the driver name “bcmcf” in the unknown card dialog.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print
XMP Toolkit                     : 3.1-701
About                           : 51eb5287-0b59-11dc-0000-086279158090
Producer                        : AFPL Ghostscript 8.54
Modify Date                     : 2007:05:23 15:23:33+08:00
Create Date                     : 2007:05:23 15:18:25+08:00
Creator Tool                    : PDFCreator Version 0.9.2
Metadata Date                   : 2007:05:23 15:23:33+08:00
Document ID                     : 51eb5287-0b59-11dc-0000-086279158090
Instance ID                     : uuid:f0f65d91-b890-460a-9bfb-b25923aa5b62
Format                          : application/pdf
Title                           : manual 1
Creator                         : Teresa
Page Count                      : 9
Author                          : Teresa

EXIF Metadata provided by EXIF.tools