Datalogic ADC PBT7K Class 1 BT Radio User Manual

Datalogic ADC, Inc. Class 1 BT Radio

UserManual.wiki >

Datalogic ADC >

PBT7K User Manual >

User Manual Base

Contents

1. User Manual Base
2. User Manual Scanner
3. Module Guidance Document

User Manual Base

PowerScan® PBT7100Base StationQuick Reference Guide

Quick Reference Guide 1Table of ContentsStatement of Agency Compliance ........................................................... 3FCC Class B Compliance Statement .................................................. 3Canadian Notice ............................................................................ 3Solids and Water Protection ............................................................ 3Power Supply ................................................................................ 3Laser Cautions .............................................................................. 4Software Product Policy ........................................................................ 4Getting Started ................................................................................... 7Connection ................................................................................... 7Linking the Reader to a Base Station ................................................ 8Programming ................................................................................ 9

2PowerScan® PBT7100 Base StationNOTES

Statement of Agency ComplianceQuick Reference Guide 3Statement of Agency ComplianceThis device complies with part 15 of the FCC Rules. Operation is subject to the following two con-ditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Class B Compliance StatementThe user is cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter-ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following mea-sures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio or television technician for help.FCC RF Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits under Specific Absorption Rate (SAR) tests for portable devices operating closer than 20 cm to nearby persons, set forth in an uncontrolled environment. The reader has been demonstrated to meet these RF emissions safety limits.Canadian NoticeThis equipment does not exceed the Class B limits for radio noise emissions as described in the Radio Interference Regulations of the Canadian Department of Communications.Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la classe B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.Solids and Water ProtectionThe reader is rated as IEC 529-IP65. This nomenclature designates the degree of water and dust resistance, indicating the imager is totally protected against dust and is protected against low pres-sure jets of water from all directions - limited ingression permitted.The Base Station is rated as IEC 529-IP54, indicating the unit is protected against dust, limited ingress (no harmful deposit) and is protected against water sprayed from all directions - with limited ingression permitted.Power SupplyModels require either a Listed class II or class III with a Limited Power Source (LPS). For the safety certification to bevalid, class III input power sources must be IEC/EN60950-1 (EN 60335-series, EN 60065 or relevant)approved.Input: 100 - 240 VAC Output: 5.2 VDC Max. Current: 2.4 A Max. Power: 12.5 W

4PowerScan® PBT7100 Base StationFor 4-Slot Battery Charger:Input: 100 - 240 VAC Output: 12 VDCMax. Current: 2.5 A Max. Power: 30 WUse only the authorized power supplies supplied by your Datalogic reseller. The use of any other power supplies can damage the reader and void your warranty.Laser CautionsThe imager may contain a laser pointer (this is a value-added option), which is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II and IEC 60825-1 for Class 2 products. Class II (2) products are not considered to be hazardous. Laser pointer models of the imager contain a Visible Laser Diode (VLD) at a wavelength of 635-670 nanometers and is designed so that there can be no human access to harmful levels of laser light dur-ing normal operation, user maintenance, or during prescribed service operations. See the User Man-ual for laser pointer configuration information and barcodes.Software Product PolicyDatalogic reserves the right to ship its products with the latest version of software/firmware avail-able. This provides our customers with the very latest in Datalogic software technology.The only exception to this policy is when the buyer has a signed contract with Datalogic that clearly defines the terms and conditions for making software/firmware changes in products shipped to the buyer.Datalogic Scanning, Inc. POWERSCAN® END USER LICENSE AGREEMENTNotice to End User: The Datalogic Product you have acquired contains embedded Software, which is inte-gral to the product’s operation. This Software is being provided to you under license, subject to the termsand conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have acceptedthe terms and conditions of this Agreement. If you do not intend to be bound to the terms of this Agree-ment, Datalogic is not willing to license the Software to you, you may not use the Datalogic Product or theSoftware, and you must contact the party from whom you acquired the Datalogic Product for instructions.This End User Software License Agreement (“Agreement”) is a legally binding agreement governing the licensing ofthe Software and Documentation by Datalogic, Scanning Holdings, Inc. and its wholly owned subsidiaries and affili-ates (“Datalogic”) to the entity or person who has purchased or otherwise acquired a Datalogic Product (“End User”).For purposes of this Agreement, any software that is associated with a separate end-user license agreement islicensed to you under the terms of that license agreement. Datalogic and End User hereby agree as follows: 1. Definitions.1.1 "Documentation" means materials such as user’s guides, program reference guides, quick reference guides,manuals, or similar materials associated with or related to the Datalogic Product, whether in printed, “online”,or other form. 1.2 "Proprietary Information" means: (a) source code, object code, software, documentation, and any relatedinternal design, system design, data base design, algorithms, technology, technical data or information, imple-mentation techniques, and trade secrets related to the Software, (b) any other trade secrets marked appropri-ately or identified as proprietary or confidential, and (c) any information that End User, under thecircumstances, should recognize as confidential. Proprietary Information does not include any information thatthe receiving party can establish was (1) in the public domain, (2) already in the receiving party’s possessionor rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of any other's propri-etary rights, or (4) independently developed without access to Proprietary Information.1.3 “Datalogic Product” means the Datalogic Powerscan® series, Powerscan® Imager series, Powerscan® EPseries, Powerscan® LR series, Powerscan® HD series, and/or Powerscan RF® series scanner and/or scan-ner/scale product, including all embedded Software in and all Documentation related to such product, whichhas been purchased or otherwise acquired by End User, whether obtained directly or indirectly from Data-logic.1.4 "Software" means any software or computer programs of Datalogic or its third party licensors in machine read-able form which is embedded in the Datalogic Product, whether obtained directly or indirectly from Datalogic,including any replacement, update, upgrade, enhancement or modification.CAUTIONDo not attempt to open or otherwise service any components in theoptics cavity. Opening or servicing any part of the optics cavity by unau-thorized personnel may violate laser safety regulations.

Software Product PolicyQuick Reference Guide 52. Scope Of License Granted.2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to use the Software, solelyon the Datalogic Product in which it is embedded (“designated Datalogic Product”), in machine-readable formonly, solely for End User's internal business purposes. This Agreement does not convey ownership of theSoftware to End User. Title to the Software shall be and remain with Datalogic or the third party from whomDatalogic has obtained a licensed right. As used in this Agreement, the term “purchase” or its equivalentswhen applied to the Software shall mean “acquire under license.” End User is not entitled to receipt or use ofthe source code to any Software. 2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or reman-ufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give,or otherwise transfer the Software to any other person or organization, for purposes other than as expresslyprovided in this Agreement, without Datalogic’s prior written consent.3. Transfers, Support.3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use ofthe Software on other than the designated Datalogic Product will be a material breach of this Agreement.However, Datalogic may elect not to terminate this Agreement or the granted licenses, but instead may electto notify End User that End User is deemed to have ordered and accepted a license for each breaching use.End User shall pay Datalogic the applicable list price for such licenses as of the date of such breach. 3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the DatalogicProduct to any third party unless such third party agrees with Datalogic in writing to be bound by the termsand conditions of this Agreement. Any such transfer of the Datalogic Product absent such agreement shall benull and void.3.3 End User may obtain support for Software from Datalogic at Datalogic’s standard support fees and under Dat-alogic’s standard support terms and conditions in effect at the time the support is requested.4. Intellectual Property.End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic’s third partylicensors and that the Software is protected by intellectual property laws and treaties. The license set forth in thisAgreement does not transfer to End User any ownership of Datalogic’s or its third party licensors' copyrights, patents,trademarks, service marks, trade secrets, or other intellectual property rights and End User shall have no right tocommence any legal actions to obtain such rights. End User shall not remove, modify, or take any other action thatwould obscure any copyright, trademark, patent marking, or other intellectual property notices contained in or on theDatalogic Product.5. Proprietary Information.5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret propertyof Datalogic and Datalogic’s third party licensors and End User acquires no right or interest in any ProprietaryInformation.5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Information of Datalogic orits third party licensors to any person other than End User’s authorized employees or agents who are underconfidentiality agreement, and End User shall not use the Proprietary Information other than in conjunctionwith use of the Datalogic Product exclusively for End User’s internal business purposes. End User shall takesteps to protect the Proprietary Information no less securely than if it were End User's own intellectual prop-erty. 5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the ter-mination of this Agreement. 6. Limited Warranty.6.1 Datalogic warrants that, under normal use and operation, the Datalogic Product will conform substantially tothe applicable Documentation for the period specified in the Documentation. During this period, for all repro-ducible nonconformities for which Datalogic has been given written notice, Datalogic will use commerciallyreasonable efforts to remedy nonconformities verified by Datalogic. End User agrees to supply Datalogic withall reasonably requested information and assistance necessary to help Datalogic in remedying such noncon-formities. For all defects reported to Datalogic within the warranty period, Datalogic’s liability is limited to pro-viding End User with one copy of corrections or responding to End User's problem reports according toDatalogic's standard assistance practices. Datalogic does not warrant that the product will meet End User'srequirements or that use of the product will be uninterrupted or error free, or that Datalogic's remedial effortswill correct any nonconformance. This limited warranty does not cover any product that have been subjectedto damage or abuse, whether intentionally, accidentally, or by neglect, or to unauthorized repair or unauthor-ized installation, and shall be void if End User modifies the product, uses the product in any manner other thanas established in the Documentation, or if End User breaches any of the provisions of this Agreement.6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PROVIDED “AS IS” ANDDATALOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL,WITH RESPECT TO THE PRODUCT, AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 7. Infringement.7.1 Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunderinfringe a United States patent or copyright of a third party and Datalogic will pay any damages finallyawarded against End User by a court of competent jurisdiction that are attributable to such claim or will payEnd User’s part of any settlement that is attributable to such claim, provided, that 1) End User notifies Data-logic promptly in writing of the claim, 2) Datalogic controls the defense or settlement of the claim, and 3) EndUser cooperates fully with Datalogic in such defense or settlement. All notices of a claim should be sent toDatalogic Scanning, Inc., Legal Department, 111 SW Fifth Ave. Suite 4100, Portland, OR 97204-3644.7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for End User the rightto continue using the Datalogic Product, 2) modify the Datalogic Product so that it becomes non-infringing,3) replace the Datalogic Product with an equivalent product not subject to such claim, or 4) provide End Useran opportunity to return the Datalogic Product and receive a refund of the purchase price paid, less a reason-able allowance for use.

6PowerScan® PBT7100 Base Station7.3 Datalogic shall have no liability to End User for claims of infringement based upon 1) the use of any DatalogicProduct in combination with any product which Datalogic has not either furnished or authorized for use withsuch Datalogic Product 2) the use of any Datalogic Product designed, manufactured, or modified to the spec-ifications of End User, or 3) End User’s modification of the Datalogic Product without written authorizationfrom Datalogic.7.4 THE FOREGOING STATES DATALOGIC’S COMPLETE AND ENTIRE OBLIGATION CONCERNINGCLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELSAND SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PAR-TIES CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CON-TEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHERORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES.8. Limitation Of Liability.EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST ENDUSER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY,WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIA-BILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DAT-ALOGIC PRODUCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANYTHIRD PARTY FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANYOTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OROTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAM-AGES.9. Government Restricted Rights; International Use.9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for com-puter software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS252.227-7013(c)(1)(ii), whichever is applicable. 9.2 If End User is using the Datalogic Product outside of the United States, End User must comply with the appli-cable local laws of the country in which the Datalogic Product is used, with U.S. export control laws, and withthe English language version of this Agreement. The provisions of the “United Nations Convention on Interna-tional Sale of Goods” shall not apply to this Agreement.10. Termination.10.1 Either party may terminate this Agreement or any license granted under this Agreement at any time upon writ-ten notice if the other party breaches any provision of this Agreement.10.2 Upon termination of this Agreement, End User immediately shall cease using any non-embedded softwareand shall return to Datalogic or destroy all non-embedded software covered by this Agreement, and shall fur-nish Datalogic with a certificate of compliance with this provision signed by an officer or authorized represen-tative of End User. For embedded software, End User agrees to sign a waiver prepared by Datalogicconcerning further use of the embedded Software. End User’s resumed or continued use of the embeddedSoftware after termination shall constitute End User’s agreement to be bound by the terms and conditions ofthis Agreement for such use. 11. General Provisions.11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relating tothe licensing of the Software and supersedes all prior or contemporaneous agreements, written or oral,between the parties concerning the licensing of the Software. This Agreement may not be changed,amended, or modified except by written document signed by Datalogic. 11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be effectivewhen received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of Contract Admin-istration, Datalogic Scanning Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may bespecified by Datalogic in writing. 11.3 Waiver. A party’s failure to enforce any of the terms and conditions of this Agreement shall not prevent theparty’s later enforcement of such terms and conditions. 11.4 Governing Law; Venue:This Agreement and the rights of the parties hereunder shall be governed by and con-strued in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing con-flicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane countiesshall have exclusive jurisdiction over all matters regarding this Agreement, except that Datalogic shall havethe right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territoryin which End User resides, or in which any of End User's assets are located.11.5 Attorneys’ Fees. In the event an action is brought to enforce the terms and conditions of this Agreement, theprevailing party shall be entitled to reasonable attorneys’ fees, both at trial and on appeal. - END -

Quick Reference Guide 7Getting StartedConnectionFigure 1 shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before connection and consult the manual for that equipment (if necessary) before proceeding.Base Station Connection and Routing — Fully insert the Power Cable and Interface (I/F) Cable connectors into their respective ports in the underside of the Base Station (see Figure 1). Alternatively, you can either loop the cables around the routing clips and back through the routing channel to the front of the Base Station as shown, or the cables can be fed directly out the back of the Base Station via the routing clips.Optional Power Connection — Plug the AC Adapter into an approved AC wall socket with the cable facing downwards (as shown in Figure 1) to prevent undue strain on the socket.Figure 1. Connecting the Base StationCAUTIONThis Base Station MUST be used with a Datalogic approved powersupply. It is not designed to obtain its power off of the terminal(POT). Connection to a host terminal without first connecting theexternal power supply may result in damage to the terminal.Bottom of Base StationRoutingClipsBaseStationI/F CablePower CableRoutingChannelPower CableOptionalAC AdapterI/FCable

8PowerScan® PBT7100 Base StationHost Connection — Typically, the interface type was specified at the time your reader and/or Base Station was ordered, however you should verify before connection that the Base Station’s cable type is compatible with your host equipment. Most connections plug directly into the host device as shown in Figure 2. Keyboard Wedge interface cables have a ‘Y’ connection where its female end mates with the male end of the cable from the keyboard and the remaining end at the keyboard port on the terminal/PC.Figure 2. Connecting to the HostLinking the Reader to a Base StationTo link a reader to a Base Station, press the Link Button on the Base Sta-tion (see Figure 3) for at least one second to place the base in "Link Mode"then scan the link barcode located on the Base Station itself using the reader to be linked. Allow the system several seconds to create the association between the two units and exit Link Mode. A successful link is indicated by three ascending tones from the reader. A “high-low-high-low” tone indicates the link attempt was unsuccessful. A single LED flash during this tone indicates no Base Station was discovered. Two green LED flashes during this tone indicates that more than one Base Station was discovered and the reader did not link.USBIBMKeyboardWedgeRS-232or...or...or...

Getting StartedQuick Reference Guide 9Figure 3. Labeling and NomenclatureProgrammingThe Base Station is typically factory-configured with a set of default fea-tures. You can select other options and customize your system through use of the instructions and programming barcodes available in the Prod-uct Reference Guide (PRG). You can view and download this and other manuals from the website listed on the back cover of this manual.NOTEPowerScan® PBT7100 readers and Base Stationscan be configured to be compatible with Power-Scan® 7000BT imagers and Base Stations. Consultthe Product Reference Guide (PRG) for full details.AntennaLink Bar CodeScanner LatchLinkButtonAmber LEDGreenLEDRegulatoryLabel(on underside)This illustration shows label placement ONLY.For actual regulatory, patent and other applicableinformation, view the labels on the product intself,or call your nearest sales or service office.

10 PowerScan® PBT7100 Base StationSelect the desired interface by scanning the associated barcode below.INTERFACE SELECTION BARCODERS-232StandardRS-232Wincor-NixdorfRS-232 for OPOS/UPOS/JavaPOSWandEmulationIBM 46XXPort 5BIBM 46XXPort 9BUSB HID POSUSB Comaa. Download the correct USB Com driver from www.datalogic.comUSBKeyboardUSB AlternateKeyboardUSB OEM

Getting StartedQuick Reference Guide 11Interface selection — continuedINTERFACE SELECTION BARCODEKeyboard ATKeyboard Wedge for PS/2 25-286, 30-286, 50, 50Z,60, 70, 80, 90 & 95 w/Standard Key EncodingKeyboardAT-NK Keyboard Wedge for IBM AT PS2 with standard key encodingbut without external keyboardKeyboardAT-ALT Keyboard Wedge for AT, PS/2 25-286, 30-286, 50,50Z, 60, 70, 80, 90 & 95 w/Alternate KeyKeyboardAT-ALT-NK Keyboard Wedge for IBM AT PS2 with alternate keyencoding but without external keyboardKeyboard XTKeyboard Wedge for PC/XT w/Standard Key EncodingKeyboardIBM 3153Keyboard Wedge for IBM Terminal 3153KeyboardIBM-M Keyboard Wedge for IBM Terminals31xx, 32xx, 34xx, 37xx make only keyboard

12 PowerScan® PBT7100 Base StationInterface selection — continuedKeyboardIBM-MB Keyboard Wedge for IBM Terminals31xx, 32xx, 34xx, 37xx make break keyboardKeyboardDIG-VTKeyboard Wedge for DIGITAL Terminals VT2xx, VT3xx, VT4xxKeyboardUSB-KBD-Apple USB Keyboard for Apple computers

EUROPEAN DECLARATION OF CONFORMITYDatalogic Scanning, Inc. hereby declares that the apparatus specified below has been tested and found compliant to the following European Council Directives and Harmonized Standards:Apparatus: PowerScan PBT7100 SystemBrad WestDate: TBDVice President Supply Chain OperationsDatalogic Scanning, Inc.Directives: EMC 2004/108/ECLow Voltage 2006/95/ECR&TTE 1999/5/ECRoHS 2002/95/ECWEEE 2002/96/ECStandards: EN 301 489-1 v 1.6.1 referenceEN 301 489-17 v 1.2.1:2002 Radio ImmunityEN 300 328 v 1.7.1: 2006 Radio EmissionsEN 50371:2002 Human exposure to electromagnetic fieldsEN 61000 6-2:2005 Generic Immunity - for Industrial Environments. Includes EN61000-4-2 (ESD), 4-3 (Radiated immu-nity), 4-4 (EFT), 4-5 (Surge), 4-6 (Cond Immunity) and 4-11 (voltage dips/interruptions)IEC 60950-1:2007 ITE SafetyEN 60825-1: 2007 Laser SafetyEN 61000-3-2: 2000 Harmonic CurrentEN 61000-3-3:1995+A1:2001 Voltage Fluctuation/Flicker UL 1642, UL 2054, UN 38.3 Safety - Li-ion Battery PackEquipmentType: Handheld Barcode Scanning EquipmentInterfaceProtocol: RS-232, USB, Keyboard Wedge, IBMPlaced intoEU Service: January 2009 under the Datalogic logoResponsibleManufacturer: Datalogic Scanning, Inc. 959 Terry St. Eugene, Oregon 97402 USA

© 2008 Datalogic Scanning, Inc. R44-2974 (Rev. X2) 10/08Datalogic Scanning, Inc.959 Terry StreetEugene, OR 97402Telephone: (541) 683-5700Fax: (541) 345-7140www.scanning.datalogic.comAustraliaDatalogic Scanning Pty LtdTelephone: [61] (2) 9870 3200australia.scanning@datalogic.comFrance and BeneluxDatalogic Scanning SarlTelephone: [33].01.64.86.71.00france.scanning@datalogic.comGermanyDatalogic Scanning GmbHTelephone: 49 (0) 61 51/93 58-0germany.scanning@datalogic.comIndiaDatalogic Scanning IndiaTelephone: 91- 22 - 64504739india.scanning@datalogic.comItalyDatalogic Scanning SpATelephone: [39] (0) 39/62903.1italy.scanning@datalogic.comJapanDatalogic Scanning KKTelephone: 81 (0)3 3491 6761japan.scanning@datalogic.comLatin AmericaDatalogic Scanning, IncTelephone: (305) 591-3222latinamerica.scanning@datalogic.comSingaporeDatalogic Scanning Singapore PTE LTDTelephone: (65) 6435-1311singapore.scanning@datalogic.comSpain and PortugalDatalogic Scanning Sarl Sucursal en EspañaTelephone: 34 91 746 28 60spain.scanning@datalogic.comUnited KingdomDatalogic Scanning LTDTelephone: 44 (0) 1923 809500uk.scanning@datalogic.com

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2024 UserManual.wiki | Privacy Policy

Contact Us
DMCA