Datamatic DOREO9 MOSAIC Oreo 9 PCMCIA Radio Module User Manual ODYDOREO9 Installation Manual

Download:
Mirror Download [FCC.gov]
Document ID	1465792
Application ID	3tz+Z/6hSxK/GA8y0grsBw==
Document Description	USER MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.93kB (36603 bits)
Date Submitted	2011-05-16 00:00:00
Date Available	2011-05-16 00:00:00
Creation Date	2011-01-20 14:15:33
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2011-01-20 14:15:33
Document Title	Microsoft Word - ODYDOREO9 Installation Manual.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	andrewp

Installation Manual
For
MOSAIC(R) OREO 9 PCMCIA Module
1/20/2011
Integration Service Personnel: Before you install the module, you require the
following items and information included in this manual.
The Module is installed into a mobile data terminal, vehicle-mounted device, or
other mobile computing device with:
1.) A PCMCIA Type II slot
2.) Approved antenna: Internal antenna, P/N 650019-0001 or antenna end cap, P/N:
CE5B-FLX10, with fitted with MMCX connectors.
3.) Terminal running Microsoft Windows CE Version 4.2 or 5.0
Getting Started:
To complete the setup of your OREO9, perform the following four steps:
1. Install the driver CAB file containing the driver.
2. Install the OREO9 into your host device’s PCMCIA slot
3. Configure the mode of operation
4. Connect to your wireless device or network
Note: It is recommended that you complete the steps in order. If you insert the card in
your device before you install the software, then the “Found New Hardware Wizard”
screen will appear, and you must select “Cancel” to cancel the Hardware Wizard.
1. Install the software
a) Download the appropriate “cab” file for the type of terminal device you are building.
The “cab” file is the software equivalent of a ‘file cabinet’ which contains the driver for the
radio.
b) Copy the file to your device using a supported file transfer mechanism.
Common methods of moving the file include:
- Placing the file on a supported Compact Flash or SD memory card and use that
card for copying the file to the device
- Use a program such as FTP or Microsoft ActiveSync
c) On the device, use the resident File Explorer program to locate the “cab” file
d) Run the “cab” file by double-clicking the file or by right-clicking and selecting “run”
e) If asked to replace any existing files on the device, answer “yes to all”
2. Install the OREO9 into the host device
a) Insert the OREO9 card into the Type II PCMCIA slot
1/20/2011
b) Connect the device’s antenna to the OREO9 via the MMCX connector. Secure the
end cap if used.
3. Configure the mode of operation
a) Select Programs, then Settings, then the Serial Port tab at the bottom of the Settings
screen
b) Select the port labeled OREO9, and select a baud rate of 57.6 KBaud
4. Connect to your wireless device or network
To use the OREO9 to connect to your wireless device, do the following:
a) From the Start menu, select Programs, then select the directory called Datamatic and
run program.
b) When a pop-up screen prompts for a name, enter any alpha-numeric name to
identify this configuration. Also enter the desired synchronization word and radio mode
used by the network or device.
c) Tap the OK button to return to the Config tab
d.) Execute a wake and read command for Star Mode device, or a read device
command for a Mesh Mode device.
Radio Information:
Datamatic declares that the OREO9 (FCC ID: ODYDOREO9) is limited in CH1~CH50
FHSS for 902.5 – 927 MHz ISM operation by specified firmware controlled in U.S.A.
This device is intended for host device integrators only under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
IMPORTANT NOTE: In the event that the two conditions above cannot be met (for
example certain device configurations or co-location with another transmitter), then the
FCC authorization is no longer considered valid and the FCC ID cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible for
reevaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users, for
example, mobile data terminals (MDTs) and vehicle-mounted devices (VMDs). The final
end product must be labeled in a visible area with the following: “Contains TX FCC ID:
ODYDOREO9”.
1/20/2011
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
IC (Canada)
To prevent radio interference to the licensed service, this device is intended to be
operated indoors and away from windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject to licensing.
1/20/2011

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2011:01:20 14:15:33-06:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2011:01:20 14:15:33-06:00
Format                          : application/pdf
Title                           : Microsoft Word - ODYDOREO9 Installation Manual.doc
Creator                         : andrewp
Document ID                     : uuid:3b8be59d-cbc7-4177-8aee-f9e930c281c9
Instance ID                     : uuid:e5843823-e17d-4acf-b3b8-16ee7ce20d48
Page Count                      : 4
Author                          : andrewp

EXIF Metadata provided by EXIF.tools