Dayton BKM4AB Bike speed transmitter with 2.4GHz functionality User Manual 2015 05 19 2in1 Digital Sensor Manual fa JP

Dayton Industrial Co., Ltd. Bike speed transmitter with 2.4GHz functionality 2015 05 19 2in1 Digital Sensor Manual fa JP

User Manual

中文使用說明書內需加註低功率警語，請參考如下警語．本機限在不干擾合法電臺與不受被干擾保障條件下於室內使用．經審驗合格之射頻電信終端設備，非經許可，公司、商號使用者均不得擅自變 更頻率、加大功率或變更原設計之特 性及功能。．射頻電信終端設備之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾 時方得繼續使用。所謂合法通信係指依電信法規定作業之無線電信。．輸入、製造射頻電信終端設備之公司、商號或其使用者違反本辦法規定，擅自使用或 變更無電頻率、電功率者，除 依電信法規定處罰外，國家通訊傳播委員會(NCC)並得撤銷其審驗合格證明。：FCC ID: O4GBKM4ABMADE IN CHINAThis device complies with part 15 of the FCC Rules.Operation is subject to the following conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.NOTES:THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. ANY CHARGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE GRANTEE OF THIS DEVICE COULD VOID THE USER’S AUTHORITY TO OPERATE THE DEVICE.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is corrected.-- Consult the dealer or experienced radio / TV technician for help.IC: 7666A-BKM4AB-English:This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions: (1) this device may not causeinterference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device.French:Leprésent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radioExempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement."NOTES:(i) This device shall be installed and operated in a completely enclosed container to prevent RF emissions, which otherwise can interfere with aeronautical navigation. Installation shall be done by trained installers, in strict compliance with the manufacturer’s instructions. (ii) The use of this device is on a “no-interference, no-protection” basis. That is, the user shall accept operations of high-powered radar in the same frequency band which may interfere with or damage this device. However, level probing devices found to interfere with primary licensing operations will be required to be removed at the user’s expense.(iii) The RF explosure compliance distance: 20mm

Navigation menu