Dell Powerconnect 8024F Troubleshooting Efficient Video Distribution Networks With.Multicast: IGMP Querier And PIM DM

Dell-Powerconnect-8024-Troubleshooting-114494 dell-powerconnect-8024-troubleshooting-114494

Dell-Powerconnect-7048R-Troubleshooting-114492 dell-powerconnect-7048r-troubleshooting-114492

Dell-Powerconnect-7048P-Troubleshooting-114488 dell-powerconnect-7048p-troubleshooting-114488

Dell-Powerconnect-7024P-Troubleshooting-114480 dell-powerconnect-7024p-troubleshooting-114480

Dell-Powerconnect-7024F-Troubleshooting-114476 dell-powerconnect-7024f-troubleshooting-114476

2014-11-13

: Dell Dell-Powerconnect-8024F-Troubleshooting-114497 dell-powerconnect-8024f-troubleshooting-114497 dell pdf

Open the PDF directly: View PDF PDF.
Page Count: 20

Victor Teeter
Network Solutions Engineer
Version 1.1
Efficient Video Distribution Networks
with.Multicast: IGMP Querier and PIM-DM
A Dell technical white paper
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
2
This document is for informational purposes only and may contain typographical errors and
technical inaccuracies. The content is provided as is, without express or implied warranties of any
kind.
© 2013 Dell Inc. All rights reserved. Dell and its affiliates cannot be responsible for errors or omissions
in typography or photography. Dell, the Dell logo, and PowerEdge are trademarks of Dell Inc. Intel and
Xeon are registered trademarks of Intel Corporation in the U.S. and other countries. Microsoft,
Windows, and Windows Server are either trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries. Other trademarks and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Dell disclaims
proprietary interest in the marks and names of others.
April 2013| Rev 1.1
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
3
Contents
Introduction ........................................................................................ 4
Multicast Overview ................................................................................ 4
Scenarios in this Document ....................................................................... 5
Scenario 1: Layer 2 Video Distribution on a Single VLAN (Using IGMP Querier) ..... 5
Multicast Using IGMP Querier Setup ................................................... 6
Testing the Multicast Setup ........................................................... 10
Troubleshooting Tips ................................................................... 11
Scenario 2: Layer 3 Video Distribution with Multiple VLANs (Using PIM-DM) ...... 12
Multicast Using PIM-DM Setup ......................................................... 12
Testing the Multicast Setup ........................................................... 17
Troubleshooting Tips ................................................................... 18
Multicast Frames Explained .................................................................... 19
Bandwidth Considerations ...................................................................... 19
Useful Links ....................................................................................... 19
About Dell ......................................................................................... 20
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
4
Introduction
Dell PowerConnectTM firmware revision 5.1 has added vast improvements in the areas of IGMP (Internet
Group Management Protocol) snooping and IP Multicast Failover. Starting with PowerConnect 5.1
firmware, Dell PowerConnect users have a new set of commands to configure IGMP snooping, MLD
snooping, MVR (Multicast VLAN Registration), and bridge multicast filtering. This white paper uses
several of the new commands to show how an administrator would set up common video distribution
networks.
PowerConnect 5.1 firmware is supported on the following Dell PowerConnect devices:
M6220 7024 7048P 8132
M6348 7024F 7048R 8132F
M8024 7024P 8024 8164
M8024k 7048 8024F 8164F
Multicast Overview
Multicast services are used to distribute streaming media, such as audio and video traffic, over the
network. These applications typically generate large amounts of traffic taking up network bandwidth.
Both multicast and broadcast allow a network device to send single packets to multiple destinations.
The difference is broadcast is designed to forward packets to all nodes on the VLAN, whereas multicast
is designed to only forward to nodes in a multicast group. Multicast is therefore a better solution when
trying to conserve network bandwidth. Also, since all nodes must process every frame they receive,
multicast saves processing cycles on nodes that do not need to receive the multicast frames.
The multicast model consists of groups, transmitters, and receivers. A typical multicast group contains
one transmitter (or sender) and one or more receivers. The receiver sends a “group join” message to
network switches and routers via the Internet Group Multicast Protocol (IGMP). The switches and
routers then forward multicast traffic only to the receivers that have joined the multicast group.
Dell PowerConnect switches by default will forward multicast frames to all interfaces in a VLAN. No
additional configuration is required to pass this traffic; however, the default behavior provides no
benefit over using broadcast. To limit unnecessary traffic on the network, an IGMP Querier (layer 2) or
PIM router (layer 3) must be seen on the network for multicast to stop broadcasting to all ports.
Starting with firmware 5.1.0.0, IGMP snooping is enabled on all switches; however, this does not keep
the multicast traffic from broadcasting until the switches can see a Querier or PIM router.
Note: By creating an IGMP Querier or PIM router on the network, switches are able to stop multicast
frames from being broadcasted and can forward those frames to transmitters and receivers in a
specified multicast group.
Switches can use IGMP snooping to automatically collect information about which interfaces are
participating in multicast groups. The switches then use this information to direct multicast traffic
away from devices that are not interested in the IP multicast traffic.
Switches that are not “multicast aware” can use static multicast groups to manually select the
interfaces that will pass multicast traffic.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
5
IGMP snooping and static multicast groups accomplish the same task. One is dynamic; requiring less
setup and maintenance, while the other is static; requiring more setup and maintenance time. This
paper only discusses how to set up the dynamic IGMP snooping feature with and without a PIM router.
If it is desired to set up Static multicast groups, please see the documentation that came with your
particular switch for instructions.
Scenarios in this Document
This document provides instructions for setting up two scenarios. In the first scenario, the desire is to
keep the multicast network Layer 2 switched only, and therefore the IGMP snooping querier is used to
perform the query functions of a Layer 3 multicast router.
The second scenario explores PIM and IGMP enabled in a Layer 3 network with IP multicast routing
between multiple VLANs. In this case, the IP multicast router acts as the IGMP querier.
Firmware Versions
The firmware used on the PowerConnect 8100 switches in these scenarios was version 5.1.0.0. Only
attempt these setups after updating firmware to 5.1.x.x or later on each participating switch. As
always, it is best practice to update all BIOS code on computers and use the latest NIC drivers.
Scenario 1: Layer 2 Video Distribution on a Single VLAN (Using IGMP Querier)
The first scenario for this paper consists of three PowerConnect switches, a video server, and multiple
clients to receive the streaming video. The particular setup for generating this document contains a
Dell PowerEdge R815 (Video Server), three Dell PowerConnect 8132 switches, and three Dell laptops for
use as multicast receivers (Figure 2). VLC Media Player is used on a Windows server and Windows
clients to generate and receive the multicast stream. The server is Windows Server 2008 R2
Enterprise, and clients include both Windows 7 and Windows XP.
This white paper includes instructions on how to set up and configure the hardware, how to download
and install the VLC Media Player, and then how to test the entire setup using VLC.
Single VLAN Video Distribution Using IGMP Querier Figure 1.
Video
Server VLAN 10 with
IP addr: 10.0.0.1 /24
VLAN 10 with
IP addr: 10.0.0.2 /24
VLAN 10 with
IP addr: 10.0.0.3 /24
IP addr: 10.0.0.50 /24
Client
IP addr: 10.0.0.52 /24
Enable IGMP
snooping and IGMP
querier
Enable IGMP
snooping
Client
IP addr: 10.0.0.51 /24
Client
IP addr: 10.0.0.53 /24
Enable IGMP
snooping
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
6
Without IGMP snooping, multicast packets are broadcast throughout the network, causing unnecessary
traffic. This impedes the efficiency of both the network and every system on the network that has to
process and drop multicast packets they were not expecting. For example, all three laptops in Figure 2
would receive the traffic although only one or two of them may desire to.
Follow the steps below to set up and test the Multicast topology shown in Figure 2.
Multicast Using IGMP Querier Setup (CLI commands are given below)
Note: Best practice, particularly in a production environment, is to configure new switches before
connecting them into the existing network. In an isolated test network such as this, it is okay to
connect the switches together in the first step, provided they have no significant configuration other
than for management. This will allow the administrator to telnet to each switch for configuring.
Otherwise, use a console cable to each switch for configuring, and make cabling the switches together
the last step.
1. Bring up all three switches and connect them together in a daisy chain with a LAG or single
cable between switches as shown in Figure 2.
2. On all three switches, create VLAN 10. Assign VLAN 10 an IP address on each switch so that
each switch’s VLAN 10 is on the same subnet.
Note: Non-querier switches such as the second and third switch here, do not require a VLAN IP
address, but it is nice to have for management and troubleshooting purposes.
3. For each trunk port (going from one switch to another switch), configure the port in trunk
mode and assign it to VLAN 10.
4. Plug in the server at one end of the network and the clients at the opposite end as shown in
Figure 2.
5. On the two end switches, for each access port (going to a video server or client), configure the
port in access mode and assign them VLAN 10.
6. Provide the server and each client an IP address within the same subnet as VLAN 10. For this
example we gave the video server an IP address of 10.0.0.50, and we gave the clients IP
addresses 10.0.0.51 through 10.0.0.53.
7. From a client, ping the server and all three VLAN IP addresses on the three switches to ensure
the network is configured correctly.
8. Enable IGMP snooping on VLAN 10 on all three switches.
Note: With PowerConnect 5.1 and later firmware, IGMP snooping is enabled globally and on all
VLANs by default. The vlan parameter is used to enable IGMP snooping on a specific VLAN, and
the no parameter is used to remove IGMP snooping from a particular VLAN.
9. Remove IGMP snooping on VLAN 1.
10. Enable IGMP querier on the switch closest to the video server.
On a layer 2 network with a single VLAN, IGMP snooping must be enabled on all switches in the
multicast route. With PowerConnect 5.1, IGMP snooping is enabled by default. A PIM router is not
required for Multicast Routing to occur on a layer 2 network with one VLAN.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
7
CLI Commands
Switch 1. Enter or cut and paste the following on the first switch (closest to the Video Server):
configure
vlan database
vlan 10
exit
interface vlan 10
ip address 10.0.0.1 255.255.255.0
exit
no ip igmp snooping vlan 1
ip igmp snooping querier
ip igmp snooping querier query-interval 20
ip igmp snooping querier vlan 10
interface Te1/0/23
switchport access vlan 10
switchport mode access
exit
interface Te1/0/24
switchport mode trunk
switchport trunk allowed vlan 10
switchport trunk native vlan 10
exit
set to 20 to speed up test (see CLI
guide for more details)
connected to Video Server
connected to second switch
Switch 2. Enter or cut and paste the following on the middle switch:
configure
vlan database
vlan 10
exit
interface vlan 10
ip address 10.0.0.2 255.255.255.0
exit
no ip igmp snooping vlan 1
interface Te1/0/23
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allowed vlan 10
exit
interface Te1/0/24
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allowed vlan 10
exit
connected to first switch
connected to third switch
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
8
Switch 3. Enter or cut and paste the following on the third switch (closest to clients):
configure
vlan database
vlan 10
exit
interface vlan 10
ip address 10.0.0.3 255.255.255.0
exit
no ip igmp snooping vlan 1
interface range Te1/0/21-23
switchport access vlan 10
switchport mode access
exit
interface Te1/0/24
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allowed vlan 10
exit
3 ports connected to 3 clients
connected to middle switch
Server and Client Setup
1. Download VLC Media Player for Windows:
http://www.videolan.org/vlc/download-windows.html
Note: In writing this paper, version 2.0.5 was used for the server and versions 2.0.3 and 2.0.5
were used for the clients. Version 1.1.9 was also used as both sender and receiver and found
to be just as stable. All were tested and may be used for either role. VLC Media Player
software is also used as the steaming server software on the Video Server.
2. Install VLC to the server and all clients that you want to receive streaming video; taking all
defaults during the install process.
Create a Multicast Video
From the Dell PowerEdge R815 Multicast Server (Sender):
1. Start VLC Media Player.
2. Select Media -> Streaming -> Add.
3. Browse to a video file (we used MP4 and WMA/WMV files for streaming). Click Open.
4. Click Stream at the bottom of the window.
5. At the Stream Output window, click Next.
6. Under Destinations, select RTP/MPEG Transport Stream from the pull-down menu.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
9
7. Check the Display Locally box, and click Add.
8. In the Address field, enter a valid IPv4 multicast group address (we used 239.0.0.25).
Caution: Some multicast addresses in the multicast range are reserved. It is best
to use an address of 239.X.Y.Z, where X is not 0, 128, 144, 160, OR Y is not 0, OR Z
is not 1, 2, 3, or 4, or 13. Using a reserved address will impede you networks
efficiency. Table 1 provides some examples:
Examples of Multicast Addresses Table 1.
Good (non-reserved) multicast addresses
Bad (reserved) multicast addresses
239.0.0.5 239.0.0.6 239.0.100.99
239.1.0.2 239.3.0.1 239.0.1.1
239.0.0.1 239.0.0.2 239.0.0.13
239.128.0.4 239.144.0.1 239.0.0.3
9. Base Port must be 5004.
Note: Port 5004 is assigned to RTP media data only. See
http://www.iana.org/assignments/service-names-port-numbers/service-names-port-
numbers.xml for more information about port assignments.
10. Make sure there is a check in the Activate Transcoding checkbox.
11. If using an MP4 file, set the Profile pull-down menu to either MP4 profile:
a. Video H.264 + ACC (MP4), or
b. Video H.264 + MP3 (MP4)
If using a WMA/WMV file, use Profile: Video WMV + WMA
12. Click Stream. A multicast group is now created for others to join.
Note: Allow a few seconds for the video to begin playing locally on the Video Server. At that
point, the video is also being transmitted to the multicast stream.
Note: Some MP4 files will only display the first video frame locally on the server, but are still
being streamed to the network, which is seen by the progress bar below the display. To get
around this issue, stream WMV/WMA or other files.
13. Pressing the Loop button at the bottom of the VLC screen will keep the file playing in a
continuous loop. This is very helpful when setting up clients for testing.
From a Multicast Client (Receiver):
1. Start VLC Player.
2. Select Media -> Open Network Stream...
3. Enter the Network URL: RTP://239.0.0.25:5004 (same address from steps 8 and 9 above).
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
10
4. Click Play.
CAUTION: Seeing the video playing on the client does not ensure multicast is
working, because it may be receiving a broadcast stream if multicast is not set up
correctly. Be sure to test the multicast setup as instructed in the next section.
The client port has now joined the multicast group. Allow a few seconds for the video to begin
playing. When the Loop button on the server is pressed in, the video will repeat on the clients as well.
5. Repeat these steps on other receiver clients on the network who want to join the multicast
group and view the video.
Testing the Multicast Setup
To check the Multicast IGMP setup on each switch, run the show commands for IGMP and multicast.
Show Commands for IGMP and Multicast Table 2.
Show Commands
Description
show statistics tengigabitethernet <port> |
include Multicast
Shows number of multicast packets sent/received
on port specified.
show ip igmp snooping groups
Run on IGMP snooping switches to show ports that
have joined the group. This command can be
used seconds after joining or leaving a group to
verify the ports have in fact joined or left the
group. For this example, look for the group with
an IP ending in 0.0.1. This can be run on any
switch, but only IGMP switches will show entries.
show ip igmp snooping mrouter
Run on IGMP snooping switches to show the port
that knows where the server is. This can be run
on any IGMP snooping switches. Other switches
will not show any entries.
Use Wireshark on each client to see the UDP protocol frames being received at the client once it joins a
multicast group (hint: the UDP packets destination address will be 239.0.0.1). Upon leaving the group
(using the stop button on the VLC player), you should notice the UDP protocol frames in Wireshark will
stop being received on the client/receiver port on the switch. If pressing the Stop button on the VLC
player doesn’t stop the UDP packets from coming to the client (usually within a few seconds), then
Multicast is not working and the client ports are receiving video broadcasts. Recheck your settings and
also see Troubleshooting Tips below.
Visit http://www.wireshark.org/download.html to download the latest Wireshark.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
11
Troubleshooting Tips
If you are receiving video at the clients but no ports are showing up under 0.0.1 from the show ip igmp
snooping groups command, then Multicast is not working. They are receiving video because the traffic
is still being broadcasted to all ports (this is the default behavior of the switches). Recheck settings on
all switches.
If VLC on the client is stopped (you must press the Stop button to leave the multicast group), but
Wireshark is showing UDP traffic from 239.0.0.1, then the video is being broadcasted to all ports and
Multicast is not working. Check settings on all switches. Keep in mind that when the VLC client sends
a “leave group” message, that it takes a few seconds before the UDP frames stop.
Each time you want to leave the multicast group, be sure to do so by pressing the Stop button at the
bottom of the VLC media player or by closing the window using the X button. Pressing pause within the
player will not leave the group.
If the UDP frames are not making it to the receiver port and no video is seen at the receiver, the time
to live (TTL) value may need to be increased when starting the stream from the server. To do this, in
step 12 above, instead of clicking Stream, click Next, and set the TTL to 16. Then click Stream to
continue. This is only necessary on a routed network and does not apply to a “layer 2 only” network.
Some MP4 files will only display the first video frame locally on the VLC Video server, but are still being
streamed to the clients, which can be verified by the progress bar below the display. To get around
this issue, stream WMV/WMA or other files.
If you see traffic flooding on all ports of VLAN 10, make sure the snooping switch has learned an
mrouter port by using the command show ip igmp snooping mrouter.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
12
Scenario 2: Layer 3 Video Distribution with Multiple VLANs (Using PIM-DM)
The second scenario consists of two switches, two video servers and multiple clients to receive the
streaming videos. The particular setup for generating this document contains two Dell PowerEdge R815
(Video Servers), two Dell PowerConnect 8132 switches, and three Dell laptops for use as multicast
receivers (Figure 2Figure 2). VLC Media Player is used on a Windows server and Windows clients to
generate and receive the multicast stream. The servers have Windows Server 2008 R2 Enterprise
installed, and clients include both Windows 7 and Windows XP.
This white paper includes instructions on how to set up and configure the hardware, how to download
and install the VLC Media Player, and then how to test the entire setup using VLC. Static routes are
used for this demonstration, though OSPF or RIP will also work.
Multiple VLAN Video Distribution Using PIM-DM Figure 2.
Video Server 1
IP: 10.40.0.50 /24
Default GW=10.40.0.5
Client
10.20.0.2 /24
Vlan 10 10.10.0.5
Vlan 20 10.20.0.5
Vlan 30 10.30.0.5
Vlan 40 10.40.0.5
Client
10.10.0.2 /24
Client
10.30.0.2 /24
Enable IGMP snooping
Vlan 10 10.10.0.1
Vlan 20 10.20.0.1
Vlan 30 10.30.0.1
Enable PIM-DM
Video Server 2
IP: 10.10.0.50 /24
Default GW=10.10.0.5
Vlan 10
Vlan 20
Vlan 30
Vlan 10
Vlan 40
This scenario enables PIM on a switch to show how it routes multicast frames between VLANs.
Enabling PIM causes an IP routing switch to become a Multicast Router (or PIM Router). The Multicast
PIM router performs the same function in the Layer 3 network as the IGMP querier does in the Layer 2
network as seen in Scenario 1.
Follow the steps below to set up and test the Layer 3 Multicast topology shown in Figure 2.
Multicast Using PIM-DM Setup (CLI commands are below)
Note: Best practice, particularly in a production environment, is to configure new switches before
connecting them into the existing network. In an isolated test network such as this, it is okay to
connect the switches together in the first step provided they have no significant configuration other
than for management. This will allow the administrator to telnet to each switch for configuring.
Otherwise, use a console cable to each switch for configuring and make cabling the switches together
the last step.
1. Bring up two PowerConnect 8100 switches and connect them together with a LAG or single
cable between switches as shown in Figure 2.
2. On the first switch (closest to the Video Servers), create VLANs 10, 20, 30, and 40. Assign IP
address to each VLAN.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
13
3. Enable routing, which will set up static routing on the first switch to route between VLANs.
4. Enable PIM-DM on the first switch. PIM must be set globally as well as on each VLAN.
5. Disable IGMP snooping on the first switch. Enable IGMP globally and on each VLAN.
6. Create VLANs 10, 20, and 30 on the second switch, assigning each an IP address.
Note: Layer 2 switches do not require an IP address on each VLAN, but assigning them could
come in handy for troubleshooting connectivity.
7. Enable IGMP snooping on the second switch (this is enabled by default starting with firmware
5.1.x.x).
8. On both switches, for each trunk port (going from one switch to another switch), configure
the port in trunk mode, allowing VLANs 10, 20, and 30 on each trunk port.
9. On both switches, for each access port (going to a video server or client), configure the port
in access mode and assign them to a VLAN. For this scenario, Video Server 1 is on VLAN 10
and Video Server 2 is on VLAN 40. The first client is on VLAN 10, the second on VLAN 20, and
the third on VLAN 30.
10. Plug in the server at one end of the network and the clients at the opposite end as shown in
Figure 2. Connect one client to each VLAN. Set IP addresses on clients and servers as
required, and within the same subnet of the VLAN where they are attached.
11. Set the default gateway on each computer to point toward the router. For this example,
each computer will have the default gateway of 10.xx.0.5, where xx is the VLAN the
computer is connected to.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
14
CLI Commands
Switch 1. Enter or cut and paste the following into the first switch (routing switch):
configure
vlan database
vlan 10,20,30,40
exit
ip routing
interface vlan 10
ip address 10.10.0.5 255.255.255.0
ip igmp
ip pim
exit
interface vlan 20
ip address 10.20.0.5 255.255.255.0
ip igmp
ip pim
exit
interface vlan 30
ip address 10.30.0.5 255.255.255.0
ip igmp
ip pim
exit
interface vlan 40
ip address 10.40.0.5 255.255.255.0
ip igmp
ip pim
exit
ip multicast
ip igmp
ip pim dense
interface Te1/0/22
switchport access vlan 10
exit
interface Te1/0/23
switchport access vlan 40
exit
interface Te1/0/24
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allowed vlan 10,20,30
exit
connected to Video Server 1 on vlan 10
connected to Video Server 2 on vlan 40
connected to second switch
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
15
Switch 2. Enter or cut and paste the following into the second switch:
configure
vlan database
vlan 10,20,30
exit
ip default-gateway 10.10.0.5
interface vlan 10
ip address 10.10.0.1 255.255.255.0
exit
interface vlan 20
ip address 10.20.0.1 255.255.255.0
exit
interface vlan 30
ip address 10.30.0.1 255.255.255.0
exit
no ip igmp snooping vlan 1
ip multicast
interface Te1/0/21
switchport access vlan 10
exit
interface Te1/0/22
switchport access vlan 20
exit
interface Te1/0/23
switchport access vlan 30
exit
interface Te1/0/24
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allowed vlan 10,20,30
exit
connected to client on vlan 10
connected to client on vlan 20
connected to client on vlan 30
connected to first switch
Server and Client Setup
1. Download VLC Media Player for Windows:
http://www.videolan.org/vlc/download-windows.html
Note: In writing this paper, version 2.0.5 was used for the server and 2.0.3 for the client.
Version 1.1.9 was also used as both sender and receiver and found to be very stable. All were
tested and may be used for either role. VLC Media Player software is also used as the steaming
server software on the Video Server.
2. Install VLC to the server and all clients you wish to receive streaming video, taking all defaults
during the install process.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
16
Create a Multicast Video
From a Dell PowerEdge R815 Multicast Server (Sender):
1. Start VLC Media Player.
2. Select Media -> Streaming… -> Add.
3. Browse to a video file (we used MP4 and WMA/WMV files for streaming). Click Open.
4. Click Stream at the bottom of the window.
5. In the Stream Output window, click Next.
6. Under Destinations, select RTP/MPEG Transport Stream from the pull-down menu.
7. Check the Display Locally box, and click Add.
8. In the Address field, enter a valid IPv4 multicast group address (we used 239.0.0.25 on Video
Server 1 and 239.0.0.26 on Video Server 2).
Note: Each multicast stream must have a unique multicast group address.
Caution: Some multicast addresses in the multicast range are reserved. It is best to
use an address of 239.X.Y.Z, where X is not 0, 128, 144, 160, OR Y is not 0, OR Z is
not 1, 2, 3, or 4, or 13. Using a reserved address will impede you networks efficiency.
Table 3 provides some examples of good and bad multicast addresses.
Examples of Multicast Addresses Table 3.
Good (non-reserved) multicast addresses
Bad (reserved) multicast addresses
239.0.0.5 239.0.0.6 239.0.100.99
239.1.0.2 239.3.0.1 239.0.1.1
239.0.0.1 239.0.0.2 239.0.0.13
239.128.0.4 239.144.0.1 239.0.0.3
9. Base Port should be 5004. Port 5004 is assigned to RTP media data only. See
http://www.iana.org/assignments/service-names-port-numbers/service-names-port-
numbers.xml for more information.
10. Make sure there is a check in the Activate Transcoding checkbox.
11. If using an MP4 file, set the Profile pull-down menu to either MP4 profile:
a. Video H.264 + ACC (MP4), or
b. Video H.264 + MP3 (MP4)
If using a WMA/WMV file, use Profile: Video WMV + WMA.
12. Click Next. Increase the TTL (time to live) value to 16. Depending on the number of routers
in the network, this value may be raised or lowered at a later time.
13. Click Stream. A multicast group is now created for clients to join.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
17
Note: Allow a few seconds for the video to begin playing locally on the Video Server. At that
point, the video is also being transmitted to the multicast stream.
Note: Some MP4 files will only display the first video frame locally on the server, but are still
being streamed to the clients, which is seen by the progress bar below the display. To get
around this issue, stream WMV/WMA or other files.
14. Pressing the Loop button at the bottom of the VLC screen will keep the file playing in a
continuous loop. This is optional but is very helpful when setting up clients for testing.
From a Multicast Client (Receiver):
1. Start VLC Player.
2. Select Media -> Open Network Stream...
3. Enter the Network URL: RTP://239.0.0.xx:5004 (an address from steps 8 and 9 above).
4. Click Play.
CAUTION: Seeing the video playing on the client does not ensure multicast is working,
because it may be receiving a broadcast stream if multicast is not set up correctly. Be
sure to test the multicast setup as instructed in the next section.
The client port has now joined the multicast group. Allow a few seconds for the video to begin
playing. When the Loop button on the server is pressed in, the video will repeat on the clients as well.
Repeat the Sender and Receiver steps on the other sender (server) and receivers (clients) on the
network to create multiple multicasts groups and clients viewing multiple videos.
Testing the Multicast Setup
To check the Multicast IGMP setup on each switch, run the show commands for IGMP and multicast and
run Wireshark to capture and analyze the traffic.
Show Commands for IGMP and Multicast Table 4.
Show Commands
Description
show statistics tengigabitethernet <port> |
include Multicast
Shows number of multicast packets sent/received
on port specified.
show ip igmp snooping groups
Run from a IGMP snooping switch to show ports
that have joined the group. This command can be
used seconds after joining or leaving a group to
verify the ports have in fact joined or left the
group. For this example, look for the group with
an IP ending in 0.0.1. This can be run on an IGMP
snooping switch. Other switches will not show any
entries.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
18
Show Commands
Description
show ip igmp snooping mrouter
Run from an IGMP snooping switch to show the
port that knows where the server is. This can be
run on any IGMP snooping switches. Other
switches will not show any entries.
show ip igmp membership
Run from the PIM router to see what VLANs and IP
interfaces have joined the multicast group.
show ip igmp groups
Shows the Querier status (routers only), IP
address, and vlan interface for each group.
Use Wireshark on each client to see the UDP protocol frames being received at the client once it joins a
multicast group (hint: the UDP packets destination address will be 239.0.0.x). Upon leaving the group
(using the stop button on the VLC player), you should notice the UDP protocol frames in Wireshark will
stop being received on the client/receiver port on the switch. If pressing the stop button on the VLC
player doesn’t stop the UDP packets from coming to the client (usually within 30 seconds), then
multicast is not working and the client ports are receiving video broadcasts. Recheck your settings and
also see Troubleshooting Tips below.
Visit http://www.wireshark.org/download.html to download the latest Wireshark.
Troubleshooting Tips
If you are receiving video at the clients but no ports are showing up under 0.0.1 or 0.0.2 from the show
ip igmp snooping groups command, then Multicast is not working. They are receiving video because
the traffic is still being broadcasted to all ports (this is the default behavior of the switches). Recheck
settings on all switches. Also read Testing the Multicast Setup.
If VLC on the client is stopped (you must press the stop button to leave the multicast group), but
Wireshark is showing UDP traffic from 239.0.0.x, then the video is being broadcasted to all ports and
multicast is not working. Check settings on all switches. Keep in mind that when the VLC client sends
a “leave group” message, that it takes a few seconds before the UDP frames stop. Also read Testing
the Multicast Setup.
Each time you want to leave the multicast group, be sure to do so by pressing the stop button at the
bottom of the VLC media player or by closing the window using the X button. Pressing pause within the
player will not leave the group.
If the UDP frames are not making it to the receiver port and no video is seen at the receiver, the time
to live (TTL) value may need to be increased when starting the stream from the server. To do this,
return to step 12 above and increase the TTL value. Then click Stream to continue.
Some MP4 files will only display the first video frame locally on the VLC Video server, but are still being
streamed to the clients, which can be verified by the progress bar below the display. To get around
this issue, stream WMV/WMA or other files.
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
19
Keep in mind these general rules:
PIM does not route. Routing must be working for it to work.
No more than 3 hops should be used between the transmitter and receiver when multicast is
used. This does not include a Rendezvous Point when using PIM-SM, but only refers to the
shortest path that is taken after pruning.
Rendezvous Points (first and redundant) when using PIM-SM need to be as close to the center of
the network as much as possible.
Multicast Frames Explained
Multicast IP addresses fall in the range of 224.0.0.1 and 239.255.255.255. These multicast addresses
are only used as a destination, never as a source address. The destination addresses given to multicast
traffic is a combination of the number 01:00:5E and the last 23 bits of the multicast IP address
(ignoring the first 9 bits). Since the first octet of the MAC address has a value of 1 (01:xx:xx:xx:xx:xx),
it denotes it as a multicast MAC address and is therefore handled differently in the switch than a
unicast MAC address.
For example, the IP address 239.0.0.1 has a destination address of 01:00:5E:00:00:01, and the
multicast IP address of 239.0.0.2 has a destination address of 01:00:5E:00:00:02. These multicast
destination addresses will be seen in every multicast UDP packet captured in Wireshark.
Bandwidth Considerations
Video Streaming in high quantity or high quality takes considerable network bandwidth. Test and fine-
tune your equipment thoroughly using the User Guide and CLI Reference Guide for your particular
switches. LAGs used on access ports and trunks can also provide additional bandwidth to allow the
network and servers to handle the traffic. When using PIM-SM (not covered in this document), place
the RP in a strategic location that is most beneficial for efficient video distribution. More information
about PIM-SM, including an example, can be found in the User Guide.
Useful Links
Reference Links Table 5.
VLC Media Player
http://www.videolan.org/vlc/download-
windows.html
WireShark
http://www.wireshark.org/download.html
IPv4 Multicast Address Assignments
https://tools.ietf.org/html/rfc5771
Internet Group Management Protocol, Version 3
https://tools.ietf.org/html/rfc3376
Protocol Independent Multicast - Dense Mode
(PIM-DM)
https://tools.ietf.org/html/rfc3973
Protocol Independent Multicast - Sparse Mode
(PIM-SM)
https://tools.ietf.org/html/rfc4601
IPv4 Multicast Address Space Registry
http://www.iana.org/assignments/multicast-
addresses/multicast-addresses.xml
Considerations for Internet Group Management
Protocol (IGMP) and Multicast Listener Discovery
(MLD) Snooping Switches
http://tools.ietf.org/html/rfc4541
Efficient Video Distribution Networks with.Multicast: IGMP Querier and PIM-DM
20
About Dell
Dell is a leading technology provider to commercial and public enterprises around the world. For more
information on Dell PowerConnect products and features, visit www.dell.com/powerconnect.

Navigation menu