Dell Poweredge M1000E Installation Manual Cisco Catalyst Blade Switch 3130/3032 Hardware Guide

2015-01-05

• Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Hardware Installation Guide
• Contents
• Preface
  • Audience
  • Purpose
  • Organization
  • Conventions
  • Related Publications
  • Obtaining Documentation and Submitting a Service Request
  • Product Overview
    • Switch Features Overview
    • Other Features
      • Switch Console Port
      • 10/100/1000 Ports
      • 10-Gigabit Ethernet Module Slots
        • Cisco TwinGig Converter Module
      • LEDs
        • System LED
        • Stack LED (Only the CBS3130G-S and CBS3130X-S Switches)
        • Stack Master LED (Only the CBS3130G-S and CBS3130X-S Switches)
        • Stack Member LED (Only the CBS3130G-S and CBS3130X-S Switches)
        • RJ-45 Uplink Port LEDs
        • System Status/ID LED
        • 10-Gigabit Ethernet Module Slot Port LEDs
      • StackWise Plus Ports
      • Power Connectors
    • Management Options
      • Using the Device Manager
      • Using the Command-Line Interface
      • Using the Dell CMC
      • Other Management Options
    • Network Configurations
• Switch Installation
  • Safety Warnings
  • Dell Modular Server Chassis Architecture
  • Installing the Switch in the Server Chassis
  • Configuring the Switch
    • Connecting through the Switch Console Port
      • Connecting through the CMC
    • Waiting for POST to Complete
    • Completing the Initial Configuration
    • Using the Device Manager to Configure the Switch
    • Configuring the Switch Stack Master
  • Managing the Switch
    • Using the CLI
    • Using the Device Manager
    • Other Management Options
  • Planning and Creating a Switch Stack (Only 3130G-S and 3130X-S Switches)
    • Stack Cabling Configurations
    • Connecting the StackWise Plus Cables
  • Installing Devices in the 10-Gigabit Ethernet Slots
    • Installing X2 Transceiver Modules and Cisco Converter Modules
      • Installing a Transceiver or Converter Module
      • Removing a Module
    • Installing SFP Modules
      • Installing an SFP Module
      • Removing an SFP Module
  • Connecting to 10/100/1000 Ethernet Ports
  • Where to Go Next
• Troubleshooting
  • Diagnosing Problems
    • Verify the Switch POST Results
    • Look at the Switch LEDs
    • Confirm the Switch Connections
      • Bad or Damaged Cable
      • Ethernet and Fiber Cables
      • Link Status
      • SFP Module Port Issues
      • Port and Interface Settings
      • Ping the End Device
      • Spanning Tree Loops
    • Verify the Switch Performance
      • Speed, Duplex, and Autonegotiation
      • Autonegotiation and Network-Interface Cards
      • Cabling Distance
  • Clearing the Switch IP Address and Configuration
  • Replacing a Failed Stack Member
  • Locating the Switch Serial Number
• Technical Specifications
• Connector and Cable Specifications
  • Connector Specifications
    • 10/100/1000 Ports
      • Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices
      • Connecting to 1000BASE-T Devices
    • 10-Gigabit Ethernet Module Interfaces
    • Cisco TwinGig Converter Module Ports
    • Console Port
  • Cable and Adapter Specifications
    • 10-Gigabit Ethernet X2 Transceiver Module Cable Specifications
    • SFP Module Cable Specifications
    • Two Twisted-Pair Cable Pinouts
    • Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports
    • Identifying a Crossover Cable
    • Console Port Adapter Pinouts
• Index