Dell V515W All In One Wireless Inkjet Printer Users Manual User's Guide

2014-11-13

: Dell Dell-V515W-All-In-One-Wireless-Inkjet-Printer-Users-Manual-113664 dell-v515w-all-in-one-wireless-inkjet-printer-users-manual-113664 dell pdf

Open the PDF directly: View PDF .
Page Count: 141

Download
Open PDF In Browser	View PDF

Dell V515w User's Guide

April 2009
Machine type(s):
4443
Model(s):
2dw, 6dw

www.dell.com | support.dell.com

Trademarks
Information in this document is subject to change without notice.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the
DELL logo are trademarks of Dell Inc.; Microsoft and Windows are registered trademarks of Microsoft Corporation. Other trademarks and trade names
may be used in this document to refer to the entities claiming the marks and names of their products. Dell Inc. disclaims any proprietary interest
in trademarks and trade names other than its own.

Contents
Safety information.............................................................................7
About your printer.............................................................................8
Thank you for choosing this printer!...............................................................................................................................8
Minimizing your printer's environmental impact......................................................................................................8
Finding information about the printer...........................................................................................................................9
Understanding the parts of the printer.......................................................................................................................11

Ordering and replacing supplies...................................................13
Replacing ink cartridges....................................................................................................................................................13
Ordering ink cartridges.....................................................................................................................................................14
Recycling Dell products.....................................................................................................................................................15

Using the printer control panel buttons and menus................16
Using the printer control panel......................................................................................................................................16
Using the printer menus...................................................................................................................................................18
Changing temporary settings into new default settings......................................................................................20
Changing the Power Saver timeout.............................................................................................................................21
Resetting to factory settings............................................................................................................................................21
Saving energy with Eco-Mode........................................................................................................................................22

Using the printer software.............................................................23
Minimum system requirements.....................................................................................................................................23
Using the Windows printer software............................................................................................................................23
Updating the printer software (Windows only)........................................................................................................25
Reinstalling the printer software...................................................................................................................................25

Loading paper and original documents......................................26
Loading paper.......................................................................................................................................................................26
Saving paper default settings.........................................................................................................................................28
Loading original documents on the scanner glass.................................................................................................29
Loading original documents into the ADF.................................................................................................................29

Printing...............................................................................................31
Tips for printing....................................................................................................................................................................31
Contents

Printing basic documents.................................................................................................................................................31
Printing specialty documents.........................................................................................................................................33
Printing on both sides of the paper (duplexing) manually..................................................................................34
Working with photos..........................................................................................................................................................36
Printing from a Bluetooth-enabled device.................................................................................................................41
Managing print jobs...........................................................................................................................................................44

Copying...............................................................................................47
Tips for copying....................................................................................................................................................................47
Making copies.......................................................................................................................................................................47
Copying photos....................................................................................................................................................................47
Enlarging or reducing images.........................................................................................................................................48
Adjusting copy quality.......................................................................................................................................................48
Making a copy lighter or darker.....................................................................................................................................49
Collating copies using the printer control panel.....................................................................................................49
Repeating an image on one page.................................................................................................................................50
Copying multiple pages on one sheet.........................................................................................................................50
Making a duplex copy manually....................................................................................................................................50
Canceling copy jobs...........................................................................................................................................................51

Scanning.............................................................................................52
Tips for scanning..................................................................................................................................................................52
Scanning to a local or network computer..................................................................................................................52
Scanning to a flash drive or memory card..................................................................................................................53
Scanning photos into an editing application............................................................................................................53
Scanning documents into an editing application...................................................................................................54
Scanning directly to e-mail..............................................................................................................................................54
Scanning to a PDF...............................................................................................................................................................55
Scanning FAQ.......................................................................................................................................................................55
Canceling scan jobs............................................................................................................................................................56

Faxing.................................................................................................57
Setting up the printer to fax............................................................................................................................................57
Configuring the fax settings............................................................................................................................................68
Creating a contact list........................................................................................................................................................70
Sending faxes........................................................................................................................................................................71
Receiving faxes.....................................................................................................................................................................72
Contents

Faxing FAQ.............................................................................................................................................................................73

Networking........................................................................................80
Installing the printer on a wireless network..............................................................................................................80
Advanced wireless setup..................................................................................................................................................84
Networking FAQ..................................................................................................................................................................88

Maintaining the printer...................................................................98
Maintaining ink cartridges...............................................................................................................................................98
Cleaning the exterior of the printer..............................................................................................................................99
Cleaning the scanner glass............................................................................................................................................100

Troubleshooting.............................................................................101
Before you troubleshoot................................................................................................................................................101
Using the Service Center to solve printer problems............................................................................................101
If Troubleshooting does not solve your problem..................................................................................................101
Setup troubleshooting....................................................................................................................................................101
Jams and misfeeds troubleshooting..........................................................................................................................106
Print troubleshooting......................................................................................................................................................108
Copy and scan troubleshooting..................................................................................................................................110
Fax troubleshooting.........................................................................................................................................................112
Memory card troubleshooting.....................................................................................................................................118
Wireless troubleshooting...............................................................................................................................................119

Index.................................................................................................135

Contents

Safety information
Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
Use only the power supply and power cord provided with this product or the manufacturer's authorized
replacements.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific
manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not
responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do
not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture
and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly
for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a professional service person.
CAUTION—SHOCK HAZARD: To avoid the risk of electric shock when cleaning the exterior of the printer, unplug
the power cord from the wall outlet and disconnect all cables from the printer before proceeding.
CAUTION—SHOCK HAZARD: Do not use the fax feature during a lightning storm. Do not set up this product
or make any electrical or cabling connections, such as the fax feature, power cord, or telephone, during a lightning
storm.
SAVE THESE INSTRUCTIONS.

Safety information

About your printer
Thank you for choosing this printer!
We've worked hard to make sure it will meet your needs.
To start using your new printer right away, use the setup materials that came with the printer, and then skim the
User’s Guide to learn how to perform basic tasks. To get the most out of your printer, read the User’s Guide carefully,
and make sure you check the latest updates on our Web site.
We're committed to delivering performance and value with our printers, and we want to make sure you're satisfied.
If you do encounter any problems along the way, one of our knowledgeable support representatives will be delighted
to help you get back on track fast. And if you find something we could do better, please let us know. After all, you
are the reason we do what we do, and your suggestions help us do it better.

Minimizing your printer's environmental impact
We are committed to protecting the environment and are continually improving our printers to reduce their
environmental impact. By selecting certain printer settings or tasks, you may be able to reduce your printer's
environmental impact even further.

Conserving energy
• Eco-Mode. This feature sets the screen brightness to low and sets the printer to change to Power Saver mode
after the printer is left idle for 10 minutes. Eco-Mode is enabled by default in your printer.

• Select the lowest Power Saver timeout. The Power Saver feature puts the printer in a minimum-power standby
mode after the printer has been idle for a set amount of time (the Power Saver timeout).

• Share your printer. Wireless/network printers allow you to share a single printer among multiple computers,
thus conserving energy and other resources.

Conserving paper
• Print more than one page image on one side of the paper. The “Pages per sheet” feature allows you to print
multiple pages on one sheet. You can print up to 8 page images on one side of a sheet of paper.

• Print on both sides of the paper. Duplexing lets you print on both sides of the paper manually or automatically
(depending on your printer model).

• Preview print jobs before printing. Use the preview features found in the Print Preview dialog or the printer
display (depending on your printer model).

• Scan and save. To avoid printing multiple copies, you can scan documents or photographs and save them to a
computer program, application, or flash drive for presentation.

• Use recycled paper.

Conserving ink
• Use Quick Print or Draft Mode. These modes can be used to print documents using less ink than normal and
are ideal for printing documents that are mostly text.

• Use High Yield cartridges. Inks in High-Yield cartridges allow you to print more pages with fewer cartridges.
About your printer

• Clean the printhead. Before replacing and recycling your ink cartridges, try using the “Clean Printhead” and
“Deep Clean Printhead” features. These features clean the printhead nozzles to improve the quality of your prints.

Recycling
• Return empty ink cartridges for reuse or recycling through the Dell Cartridge Collection Program. To return
an empty ink cartridge, go to www.dell.com/recycling to request a postage-paid bag.
• Recycle the product packaging.

• Recycle your old printer instead of throwing it away.
• Recycle paper from discarded print jobs.
• Use recycled paper.

Finding information about the printer
Publications
What are you looking for?

Find it here

Initial setup instructions:

Setup documentation

• Connecting the printer
• Installing the printer software

The setup documentation came with the printer.

Additional setup and instructions for using the printer:

User's Guide

• Selecting and storing paper and specialty media
• Loading paper
• Performing printing, copying, scanning, and faxing tasks,

The User's Guide is available on the installation software
CD.

depending on your printer model

•
•
•
•

Configuring printer settings
Viewing and printing documents and photos
Setting up and using printer software
Setting up and configuring the printer on a network,
depending on your printer model

For updates, check our Web site at support.dell.com.

• Caring for and maintaining the printer
• Troubleshooting and solving problems

About your printer

What are you looking for?

Find it here

Help using the printer software

Windows Help
Open a printer software program or application, and
then click Help.
Click

to view context-sensitive information.

Notes:

• The Help installs automatically with the printer
software.

• The printer software is located in the printer
Program folder or on the desktop, depending on
your operating system.
The latest supplemental information, updates, and online
technical support:

•
•
•
•
•
•
•

Dell Support Web site—support.dell.com
Note: Select your region, and then select your product
to view the appropriate support site.

Troubleshooting hints and tips
Frequently asked questions

Support telephone numbers and hours of operation for
your region or country can be found on the Support
Web site.
Have the following information ready when you
contact support so that they may serve you faster:

Documentation
Driver downloads
Live chat support
E-mail support

• Service Tag
• Express Service Code

Telephone support

Note: The Service Tag and Express Service Code appear
on labels located on your printer.

• Software and Drivers—Certified drivers for your printer and Installation software CD
installers for Dell printer software

Note: If you purchased your Dell computer and printer

• Readme files—Last-minute technical changes, or advanced at the same time, then documentation and drivers for
technical reference material for experienced users or
technicians

your printer are already installed on your computer.

• Supplies and accessories for your printer
• Replacement cartridges

Dell Printer Supplies Web site–dell.com/supplies

• Safety information for preparing to operate your printer
• Regulatory information
• Warranty information

Product Information Guide

You can purchase printer supplies online, by telephone,
or in select retail stores.

Product Information Guide

Note: The Product Information Guide may not be
available in your country or region.

About your printer

Understanding the parts of the printer
12

10
9
8
2
7
6
3
5

Use the

Paper support

Load paper.

Wi-Fi indicator

Check wireless status.

Memory card slots

Insert a memory card.

PictBridge and USB port

Connect a PictBridge-enabled digital camera, USB Bluetooth
adapter, or a flash drive to the printer.

Card reader light

Check card reader status. The light blinks to indicate that a
memory card is being accessed.

Paper exit tray

Hold paper as it exits.

Printer control panel

Operate the printer.

Automatic Document Feeder (ADF) paper guide Keep paper straight when feeding it into the ADF.
Note: Adjust the paper guide on the ADF tray to the width of
the original document.

ADF output tray

Hold documents as they exit from the ADF.

ADF tray

Load original documents in the ADF. Recommended for
scanning, copying, or faxing multiple-page documents.
Note: Do not load postcards, photos, small items, or thin media
(such as magazine clippings) into the ADF. Place these items on
the scanner glass.

ADF

Scan, copy, or fax multiple-page letter-, legal-, and A4-size
documents.

Paper feed guard

Prevent items from falling into the paper slot.

Paper guides

Keep paper straight when feeding.

About your printer

9
3
4
8

5
6

Use the

Top cover

Access the scanner glass.

Scanner glass

Scan and copy photos and documents.

Security slot

Install an anti-theft cable on your printer.

Power supply with port Connect the printer to a power source.

EXT Port

Connect additional devices (telephone or answering machine) to the printer and the
telephone line. Use this port if you do not have a dedicated fax line for the printer, and
if this connection method is supported in your country or region.
Note: Remove the plug to access the port.
EXT

LINE Port

Connect the printer to an active telephone line (through a standard wall jack, DSL filter,
or VoIP adapter) to send and receive faxes.

LINE

USB port

Connect the printer to a computer using a USB cable.
Warning—Potential Damage: Do not touch the USB port except when plugging in or
removing a USB cable or installation cable.

Printhead

Scanner unit

Install, replace, or remove ink cartridges.

• Access the ink cartridges and printhead.
• Remove paper jams.

About your printer

Ordering and replacing supplies
Replacing ink cartridges
Make sure you have a new ink cartridge or cartridges before you begin. You must install new cartridges immediately
after removing the old ones, or the ink remaining in the printhead nozzles may dry out.

1 Turn on your printer.
2 Open the printer.

Note: The printhead moves to the cartridge installation position.

3 Press the release tab, and then remove the used ink cartridge or cartridges.

Note: Do not reinstall used ink cartridges once you remove them from the printhead.

Ordering and replacing supplies

4 Remove the new cartridges from the foil, and then remove the protective cap from each of the ink cartridges.
Install the black ink cartridge and then the color ink cartridge. Use two hands to install each cartridge.

Note: Install the ink cartridges immediately after removing the protective cap to avoid exposing the ink to air.

5 Close the printer.

Ordering ink cartridges
Page yields available at www.dell.com/supplies. For best results, use only Dell ink cartridges.
Item

Licensed cartridge1

Regular cartridge

Black cartridge

Series 21

Series 21R

Black cartridge, high yield2

Series 23

Series 23R

Color cartridge

Series 21

Series 21R

Color cartridge, high yield2

Series 23

Series 23R

1 Licensed for a single use only. After use, return this cartridge to Dell for remanufacturing, refilling, or recycling. To know

more about recycling Dell products, visit www.dell.com/recycling.
2

Available only on the Dell Web site at www.dell.com/supplies.

Ordering and replacing supplies

Recycling Dell products
To return Dell products to Dell for recycling:

1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 Choose your printer from the printer drop-down list.
5 Click Order supplies in the Maintenance tab.
6 Click

7 Follow the instructions on the computer screen.

Ordering and replacing supplies

Using the printer control panel buttons
and menus
Using the printer control panel
The following diagrams explain the sections of the printer control panel:
1

Use the:

Power button

• Turn the printer on and off.
• Switch to Power Saver mode.
Note: When the printer is on, press to switch to
Power Saver mode. Press and hold for three seconds
to turn off the printer.

Copy button

Access the copy menu and make copies.

Scan button

Access the scan menu and scan documents.

Fax button

Access the fax menu and send faxes.

Photo button

Access the photo menu and print photos.

Using the printer control panel buttons and menus

Use the:

Display

View:

Note: The display is turned off in Power Saver mode.

Arrow buttons

Select button

• Printer status
• Messages
• Menus
Choose a menu or submenu item that appears on the
display.

• Select menu options.
• Save settings.
• Feed or eject paper. Press and hold for 3 seconds to feed
or eject paper from the printer.

Back button

Setup button

• Return to the previous screen.
• Exit from one menu level to a higher one.
Access the setup menu and change printer settings.
Note: The Copy, Scan, Fax, and Photo button lights are off
when this button is selected.
1

Use the:

Address Book Access fax numbers from a saved list of numbers.

Redial/Pause In Fax mode:

• Insert a three-second pause in a fax number to wait for an outside line or get through an
automated answering system. Enter a pause only when you have already begun entering the
number.

• Display the last number dialed. Press the left or right arrow button to view the last five numbers
dialed.

Using the printer control panel buttons and menus

Use the:

Dialtone

Dial the telephone number manually using the keypad before sending the fax.

Color/Black

Switch to color mode or black-and-white mode.

Start button

Start a print, scan, fax, or copy job, depending on which mode is selected.

Cancel button

• Cancel a print, copy, scan, or fax job in progress.
• Exit from a menu level of the Copy, Scan, Fax, Photo, or File Print menu to the top level of a
menu.

• Exit from a menu level of the Setup menu to the top level of the previous mode.
• Clear current settings or error messages, and return to default settings.
7

Keypad

In Copy mode or Photo mode: enter the number of copies or prints you want to make.
In Fax mode:

•
•
•
•

Enter fax numbers.
Navigate an automated answering system.
Select letters when creating a Speed Dial list.
Type numbers to enter or edit the date and time shown on the display.

Using the printer menus
Copy menu

Scan menu

Fax menu

PictBridge menu1

Copies

Scan to

Fax to

Paper Size

Quality

Photo Size

Quality
Lighter/Darker
Resize
Original Size
Photo Reprint
Collate
Pages per Sheet
Copies per Sheet
Content Type
ID Card Copy

• Computer
– Application
– Quality
– Original Size
• Network
– Quality
– File Type
– Original Size
• USB Flash Drive
– Quality
– File Type
– Original Size
• Memory Card
– Quality
– File Type
– Original Size

•
•
•
•

Standard

Paper Type

Fine

Layout
Quality

Superfine
Ultrafine

Lighter/Darker
Original Size

• Letter
• A4
• Legal
Schedule Fax

• Send Now
• Send Later
• View Pending

This menu appears only when a PictBridge-enabled camera is inserted into the PictBridge port.

Using the printer control panel buttons and menus

Photo menu
Easy Photo

• Print
– Last Photo
– All Photos
– Date Range
– Photo Number
• Paper Size
• Photo Size

Print Photos

• Print
– Last Photo
– All Photos
– Date Range
– Photo Number
– Print DPOF1
• Lighter/Darker

• Photo Effects
– None
– Auto Enhance
– Sepia
– Antique Grey
– Antique Brown
• Paper Size
• Photo Size
• Paper Type
• Layout
• Quality

Proof Sheet

•
•
•
•

Print Last 20
Print All
Print Date Range
Scan Sheet

Save Photos

•
•
•
•

Computer 2
Network
USB Flash Drive 3
Memory Card 3

Select Computer (appears only
in printers connected to a
network)

This menu appears only when there is a valid DPOF file in your memory device.

This menu appears only when the printer is connected to the computer through the USB port.

This menu appears only when a memory device is inserted into the card slot or USB port.

Setup menu
Paper Setup

• Paper Size
• Paper Type
Maintenance

• Ink Levels
• Clean Printhead
• Deep Clean
Printhead

• Align Printer
• Print Test Page
• Replace Printhead

Device Setup

•
•
•
•
•
•
•
•
•

Language
Country/Region
Date/Time
Host Fax Settings
Button Beep
Power Saver

Network Setup1

•
•
•
•
•
•

Auto Screen Dim
Eco-Mode
Clear Settings Timeout

Print Setup Page
Wi-Fi Protected Setup
Wireless Information
TCP/IP
File Print
Reset Network Adapter
Defaults

Fax Setup

•
•
•
•
•
•

Address Book
Reports
Ringing and Answering
Fax Printing
Dialing and Sending
Fax Blocking

Bluetooth Setup2

•
•
•
•
•
•
•
•
•
•

Enable
Discovery
Printer Name
Security Level
Paper Size
Photo Size
Paper Type
Quality
Pass Key
Clear Device List

Defaults

• Photo Print Size
• Set Defaults
– Use Current
– Use Factory
Demo Mode

• On
• Off
1

This menu appears only in printers that support wireless printing.

This menu appears only when a USB Bluetooth adapter is inserted into the USB port.

Note: The File Print menu is enabled when you insert a memory device that contains document files into the printer.
The menu is composed of the folders and files stored on the memory device.
Using the printer control panel buttons and menus

Changing temporary settings into new default
settings
The following menus revert to default settings after two minutes of inactivity or after the printer is turned off:
Copy menu

•
•
•
•
•
•
•
•

Copies
Quality
Lighter/Darker
Resize
Original Size
Pages per Sheet
Copies per Sheet
Content Type

Scan menu

• Quality
• Original Size

Fax menu (selected models
only)

• Lighter/Darker
• Quality

Photo menu

The following Photo options will not time out after two minutes of inactivity or after you
turn off the printer, but they will return to the factory default settings when a memory
card or flash drive is removed.

•
•
•
•

Photo Effects
Photo Size
Layout
Quality

To change the temporary settings into new default settings
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Defaults, and then press

3 Press the arrow buttons to scroll to Set Defaults, and then press

Use Current appears on the display.

4 Press

again to select Use Current.

5 Press

until you exit Setup, or press another mode button.

To disable the settings timeout feature
You can disable the settings timeout feature if you do not want the printer to revert to the default settings after two
minutes of inactivity or after the printer is turned off.

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Device Setup, and then press

3 Press the arrow buttons to scroll to Clear Settings Timeout, and then press
Using the printer control panel buttons and menus

4 Press the arrow buttons to scroll to Never, and then press
5 Press

until you exit Setup, or press another mode button.

Changing the Power Saver timeout
The Power Saver timeout is the time it takes for the printer to switch to Power Saver mode when the printer is left
idle. The Power Saver feature optimizes energy efficiency by reducing the printer power consumption (as much as
28 percent on some printer models) compared to the default printer settings. To save the most energy, select the
lowest Power Saver timeout.

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Device Setup, and then press
3 Press the arrow buttons to scroll to Power Saver, and then press

.
.

4 Press the arrow buttons to select a Power Saver timeout, and then press
5 Press

until you exit Setup, or press another mode button.

Resetting to factory settings
Resetting to factory default settings will delete all the printer settings you have previously selected.

Using the printer control panel menus
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Defaults, and then press

3 Press the arrow buttons to scroll to Set Defaults, and then press
4 Press the arrow buttons to scroll to Use Factory, and then press

.
.

5 When prompted to set the initial settings of your printer, make your selections using the printer control panel
buttons.
Initial Setup Complete appears on the display.

Using a button combination (if you cannot read the current
language)
1 Turn off the printer.
Note: If you have set the Power Saver timeout in the Setup menu, then press and hold the
to turn off the printer.

2 From the printer control panel, press and hold

and

, and then press

for three seconds

to turn the printer on.

3 Release all three buttons.
4 When prompted to set the initial settings of your printer, make your selections using the printer control panel
buttons.
Initial Setup Complete appears on the display.
Using the printer control panel buttons and menus

Saving energy with Eco-Mode
The Eco-Mode feature optimizes energy efficiency and saves money.
When Eco-Mode is enabled, the printer automatically switches to the following settings:

• The printer display is dimmed.
• The printer changes to Power Saver mode after ten minutes.
Notes:

• If you are using Eco-Mode, then the Eco-Mode settings override any changes you may make to individual settings
that are part of Eco-Mode.

• Eco-Mode is enabled by default.
To change the Eco-Mode setting:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Device Setup, and then press

3 Press the arrow buttons to scroll to Eco-Mode.
4 Select the Eco-Mode setting, and then press
5 Press

until you exit Setup, or press another mode button.

Using the printer control panel buttons and menus

Using the printer software
Minimum system requirements
The printer software requires up to 500 MB of free disk space.

Supported operating systems
•
•
•
•
•
•
•

Microsoft Windows 7 (Web only)
Microsoft Windows Vista
Microsoft Windows XP
Microsoft Windows 2000 (SP4 or greater)
Linux Ubuntu 8.04 LTS and 8.10 (Web only)
Linux OpenSUSE 11.0 and 11.1 (Web only)
Linux Fedora 10 (Web only)

Using the Windows printer software
Software installed during printer installation
When you set up the printer using the installation software CD, all the necessary software was installed. You may
have chosen to install some additional programs. The following table provides an overview of various software
programs and what they can help you do.
If you did not install these additional programs during initial installation, then reinsert the installation software CD,
run the installation software, and then select Install Additional Software from the Software Already Installed screen.

Printer software
Use the
Dell Printer Home
(referred to as Printer Home)

Dell Fast Pics

•
•
•
•
•
•
•
•
•
•
•

Launch applications or programs.
Access the Fax Solutions software.
Scan or e-mail a photo or document.
Edit scanned documents.
Scan documents to PDF.
Adjust settings for the printer.
Order supplies.
Maintain ink cartridges.
Print a test page.
Register the printer.
Contact technical support.

Manage, edit, transfer, and print photos and documents.

(referred to as Fast Pics)

Using the printer software

Use the

AdobeTM Photo Album Starter Edition

View, manage, and edit photos.

Dell Toolbar

Print, scan, or convert local files from Windows.

(referred to as Toolbar)
Dell Ink Management System
Dell Fax Solutions
(referred to as Fax Solutions)

Abbyy Sprint OCR
Dell Wireless Setup Utility
(referred to as Wireless Setup Utility)

Order ink.

•
•
•
•

Send a fax.
Receive a fax in three-in-one printers.
Add, edit, or delete contacts in the built-in phone book.
Access the Dell Fax Setup Utility. Use the Fax Setup Utility to set the Speed
Dial and Group Dial numbers, set Ringing and Answering, and print fax
history and status reports.

Scan a document and produce text that you can edit with a word-processing
program.

• Set up the wireless printer on a wireless network.
• Change the wireless settings of the printer.
Note: This program is installed automatically with the printer software if the
printer has wireless capability.

Dell Service Center
(referred to as Service Center)

• Troubleshoot the printer.
• Access the printer maintenance functions.
• Contact technical support.
Notes:

• This program is installed automatically with the printer software.
• You may be prompted to install this program from the Web, depending on
your printer model.
Printing Preferences

When you select File  Print with a document open and then click
Properties, a Printing Preferences dialog appears. The dialog lets you select
options for the print job, such as the following:

•
•
•
•
•
•

Select the number of copies to print.
Print two-sided copies.
Select the paper type.
Add a watermark.
Enhance images.
Save settings.

Note: Printing Preferences is installed automatically with the printer software.

Note: Your printer may not come with some of these programs or some of the functions of these programs, depending
on the features of the printer that you purchased.

Using the printer software

Updating the printer software (Windows only)
Checking for software updates
1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 Choose your printer from the printer drop-down list.
5 From the Support tab, select Check for updates.
6 Follow the instructions on the computer screen.

Reinstalling the printer software
If you encountered problems while installing, or if your printer does not appear in the Printers folder or as a printer
option when you send a print job, then try removing and reinstalling the printer software.

Uninstalling the printer software
1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select the uninstall option.
4 Follow the instructions on the computer screen to remove the software.
5 Once the uninstall process in complete, restart your computer.

Installing the printer software
Note: If you installed the printer software on this computer before but need to reinstall the software, then uninstall
the current software first.

1 Close all open software programs.
2 Insert the installation software CD.
If the Welcome screen does not appear after a minute, then launch the CD manually:

a Click , or click Start and then click Run.
b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
3 Follow the instructions on the Welcome screen.

Using the World Wide Web
Updated printer software may be available at www.support.dell.com.

Using the printer software

Loading paper and original documents
Loading paper
1 Fan the paper.

2 Center the paper on the paper support.
3 Adjust the paper guides so they rest against the edges of the paper.

Note: Do not force paper into the printer. The paper should be flat against the paper support, and the edges
should be flush against both paper guides.

Paper and specialty media guidelines
Load up to:

Make sure that:

100 sheets of plain paper

• The paper guides rest against the edges of the paper.
• You load letterhead paper with the print side faceup and
the top of the letterhead going into the printer first.

Loading paper and original documents

Load up to:

Make sure that:

25 sheets of heavyweight matte paper

• The print side of the paper is faceup.
• The paper guides rest against the edges of the paper.
• You select Automatic, Normal, or Photo print quality.
Note: Draft mode is available but is not recommended for
use with expensive paper such as heavyweight matte, labels,
photo cards and glossy paper.

20 sheets of banner paper

• You remove all paper from the paper support before
inserting banner paper.

• You use banner paper designed for inkjet printers.
• You place a stack of banner paper on or behind the
printer, and feed in the first sheet.

• The paper guides rest against the edges of the paper.
• You select A4 Banner or Letter Banner paper size.

10 envelopes

• The print side of the envelope is faceup.
• The paper guides rest against the edges of the
envelopes.

• You print the envelopes with Landscape orientation.
Note: If you are mailing within Japan, then the envelope
can be printed in Portrait orientation with the stamp in
the lower right corner or in Landscape orientation with
the stamp in the lower left corner. If you are mailing
internationally, then print in Landscape orientation with
the stamp in the upper left corner.

• You select the correct envelope size. Select the next
biggest size if the exact envelope size is not listed, and
set the left and right margins so your envelope is
correctly positioned.
25 sheets of labels

• The print side of the label is faceup.
• The paper guides rest against the edges of the paper.
• You select Automatic, Normal, or Photo print quality.
Note: Draft mode is available but is not recommended for
use with expensive paper such as heavyweight matte, labels,
photo cards and glossy paper.

Loading paper and original documents

Load up to:

Make sure that:

25 greeting cards, index cards, postcards, or photo cards

• The print side of the card is faceup.
• The paper guides rest against the edges of the cards.
• You select Automatic, Normal, or Photo print quality.
Note: Draft mode is available but is not recommended for
use with expensive paper such as heavyweight matte, labels,
photo cards and glossy paper.

25 sheets of photo/glossy paper

10 iron-on transfers

• You follow the loading instructions on the iron-on
transfer packaging.

• The print side of the transfer is faceup.
• The paper guides rest against the edges of the transfer.
• You select Automatic, Normal, or Photo print quality.
50 transparencies

• The rough side of the transparencies is faceup.
• The paper guides rest against the edges of the
transparencies.

Saving paper default settings
You can set the default paper size, paper type, and photo print size for the documents and photos that you print.
Note: These default settings apply only to print, copy, and scan jobs that you initiate from the printer.

1 From the printer control panel, press

2 Choose the default settings:
• If you want to set the default paper size:
a Press to select Paper Setup.
b Press the arrow buttons to scroll to Paper Size, and then press .
c Press the arrow buttons to select the default paper size for the printer, and then press .
• If you want to set the default paper type:
a Press to select Paper Setup.
b Press the arrow buttons to scroll to Paper Type, and then press .
c Press the arrow buttons to select the default paper type for the printer, and then press .
Loading paper and original documents

• If you want to set the default photo print size:
a Press the arrow buttons to scroll to Defaults, and then press .
b Press to select Photo Print Size.
c Press the arrow buttons to select the default photo print size for the printer, and then press
3 Press

until you exit Setup, or press another mode button.

Loading original documents on the scanner glass
1 Open the top cover and place the document facedown on the scanner glass.
2 Close the top cover.

Loading original documents into the ADF
You can load up to 35 sheets of an original document into the ADF for scanning, copying, and faxing. You can load
A4-, letter-, or legal-size paper into the ADF.

1 Adjust the paper guide on the ADF tray to the width of the original document.
2 Load the original document faceup and top edge first into the ADF until you hear a beep.

Loading paper and original documents

3 The document feeds into the ADF.

Loading paper and original documents

Printing
Tips for printing
•
•
•
•
•

Use the appropriate paper for your print job.
Select a higher print quality for better prints.
Make sure there is enough ink in the ink cartridges.
Remove each sheet as it is printed when printing photos or when working with specialty media.
Select the borderless setting when printing photos.

Printing basic documents
Printing a document
1 Load the paper in the printer.
2 Send the print job:
a With a document open, click File  Print.
b Click Properties, Preferences, Options, or Setup.
c Select the print quality, the number of copies to print, the type of paper to use, and how the pages should
print.

d Click OK to close any printer software dialogs.
e Click OK or Print.

Collating printed copies
If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the
copies as groups of pages (not collated).
Collated

Not collated

Notes:

• The collate option is available only when you are printing multiple copies.
• To prevent smudging when printing photos, remove each photo as it exits the printer, and then let it dry before
stacking.

1 With a document open, click File  Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Copies section of the Print Setup tab, enter the number of copies that you want to print, and then select
Collate Copies.
Printing

4 Click OK to close any printer software dialogs.
5 Click OK or Print.

Printing pages in reverse order
By default, the first page is printed first. If you want to reverse the order in which pages print to make documents
ready to read with the first page on top, then do the following:

1 With a document open, click File  Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Copies section of the Print Setup tab, select a page order:
• To print the last page first, select Print Last Page First.
• To print the first page first, clear the Print Last Page First check box.
Note: If two-sided printing is enabled, then you cannot print the last page first. To change the print order,
you must first disable two-sided printing.

4 Click OK to close any printer software dialogs.
5 Click OK or Print.

Printing multiple pages on one sheet
1 With a document open, click File  Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Layout list of the Advanced tab, select Pages per sheet.
4 Select the number of page images to print on each page.
If you want each page image to be surrounded by a border, then select Print Page Borders.

5 Click OK to close any printer software dialogs.
6 Click OK or Print.

Printing documents from a memory card or flash drive
To enable the File Print function:
• The printer must be connected to a computer through a USB cable or through a network.

• The printer and the computer must be on.
• The memory card or flash drive must contain document files that are supported by the printer. For more
information, see “Supported memory cards and file types” on page 37.
• The computer must contain applications that support the file types in the memory device.

1 Insert a memory card or flash drive.
When the printer detects the memory device, Memory Card Detected or Storage Device
Detected appears on the display.

2 If only document files are stored on the memory device, then the printer automatically switches to File Print mode.
If document files and image files are stored on the memory device, then press

Printing

to select Documents.

3 Select and print the document:

If the printer is using a USB connection
a Press the arrow buttons to select the file name of the document that you want to print or the folder where
the document is saved in the memory device.

b Press

, and then press

to start printing the document.

If the printer is using a Wireless connection (selected models only)
a Press the arrow buttons to select the file name of the document that you want to print.
b Press

, and then wait for the printer to connect to the network computer or to finish searching the network
for available computers.

c When prompted, press the arrow buttons to select the name of the network computer, and then press

start printing the document.
Notes:

• You may be prompted to enter a PIN if the computer requires it. Enter the PIN using the keypad.
• To assign a computer name and a PIN to the computer, see the Help for the printer software associated
with your operating system.

Printing specialty documents
Printing envelopes
1 Load the envelopes in the printer.
2 Send the print job:
a With a document open, click File  Print.
b Click Properties, Preferences, Options, or Setup.
c From the Paper Type list of the Print Setup tab, select Plain Paper.
d From the Paper Size list, select the envelope size.
Note: To print on a custom-size envelope, select Custom Size, and then specify the height and width of the
envelope.

e Select an orientation.
f Click OK to close any printer software dialogs.
g Click OK or Print.
Notes:

• Most envelopes use landscape orientation.
• Make sure the same orientation is also selected in the software application.

Printing

Printing labels
1 Load the label sheets in the printer.
2 Send the print job:
a With a document open, click File  Print.
b Click Properties, Preferences, Options, or Setup.
c From the Paper Size list of the Print Setup tab, choose a paper size that matches the size of the label sheet. If
no paper size matches the label sheet size, then set a custom size.
If necessary, choose the appropriate type of paper from the Paper Type list.

d Click OK to close any printer software dialogs.
e Click OK or Print.

Tips on loading label sheets
•
•
•
•

Make sure the top of the label sheet feeds into the printer first.
Make sure the adhesive on the labels does not extend to within 1 mm of the edge of the label sheet.
Make sure the paper guide or paper guides rest against the edges of the label sheet.
Use full label sheets. Partial sheets (with areas exposed by missing labels) may cause labels to peel off during
printing, resulting in a paper jam.

Note: Labels require more drying time. Remove each label sheet as it exits, and then allow it to dry to avoid ink
smudging.

Printing on custom-size paper
Before beginning these instructions, load the custom-size paper in the printer.

1 With a document open, click File  Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Paper Size list of the Print Setup tab, select Custom Size.
The Define Custom Paper Size dialog appears.

4 Set the paper size.
5 Select the measurement units to use (inches or millimeters).
6 Click OK to close any printer software dialogs.
7 Click OK or Print.

Printing on both sides of the paper (duplexing)
manually
1 With a document open, click File  Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click the Advanced tab.

Printing

4 From the 2-Sided Printing section, select Manual.
Note: The Print Instruction Page to Assist in Reloading item is selected automatically.

5 Click OK. The printer prints the odd-numbered pages and the instruction sheet.
6 Flip and reload the paper, following the directions on the instruction sheet to complete the print job.

Note: To return to single-sided printing, return to the Advanced tab. From the 2-Sided Printing section, select
Off from the drop-down menu.

Printing

Working with photos
Using a memory card or flash drive with the printer
Memory cards and flash drives are storage devices frequently used with cameras and computers. You can remove
the memory card from the camera or the flash drive from the computer and insert it directly into the printer.

1 Insert a memory card into the card slot or a flash drive into the USB port.
Inserting a memory card

Inserting a flash drive

Notes:

• Insert the card with the brand name label facing right.
• Make sure any arrows on the card point toward the
printer.

• If necessary, connect the memory card to the adapter

• The flash drive uses the same port that is used for a
PictBridge camera cable.

• An adapter may be necessary if your flash drive does

that came with it.

not fit directly into the port.

• Make sure that the memory card inserted is supported
by the printer. For more information, see “Supported
memory cards and file types” on page 37.
Warning—Potential Damage: Do not touch any cables, any network adapter,
any connector, the memory device, or the printer in the areas shown while
actively printing, reading, or writing from the memory card. A loss of data can
occur.

2 Look for Memory Card Detected or Storage Device Detected on the display.
Notes:

• If the printer does not recognize the memory device, then remove and reinsert it.
• If a flash drive or a digital camera set to mass storage mode is inserted into the USB port while a memory card is
in the card slot, then a message appears on the display prompting you to choose which memory device to use.
Printing

Supported memory cards and file types
Memory Card

•
•
•
•
•
•
•
•
•
•
•
•
•
•

File Type
Documents:

Secure Digital (SD)

•
•
•
•
•
•
•
•
•

Micro Secure Digital (with adapter) (Micro SD)
Mini Secure Digital (with adapter) (Mini SD)
MultiMedia Card (MMC)
Reduced Size MultiMedia Card (with adapter) (RS-MMC)
MultiMedia Card mobile (with adapter) (MMCmobile)
Memory Stick
Memory Stick PRO
Memory Stick Duo (with adapter)
Memory Stick PRO Duo (with adapter)

.doc (Microsoft Word)
.xls (Microsoft Excel)
.ppt (Microsoft PowerPoint)
.pdf (Adobe Portable Document Format)
.rtf (Rich Text Format)
.docx (Microsoft Word Open Document Format)
.xlsx (Microsoft Excel Open Document Format)
.pptx (Microsoft PowerPoint Open Document Format)
.wpd (WordPerfect)

Images:

xD-Picture Card

• JPEG
• TIFF

xD-Picture Card (Type H)
xD-Picture Card (Type M)
Secure Digital High Capacity (SDHC)

Printing photos using the printer control panel
1 Load photo paper.
2 From the printer control panel, press

3 Insert a memory card, flash drive, or digital camera set to mass storage mode.
If image files and document files are stored in the memory device, then press the arrow buttons to select
Photos.

4 Press the arrow buttons to scroll to Easy Photo or Print Photos, and then press

Notes:

• Select Easy Photo if you want to print photos quickly.
• Select Print Photos if you want to customize the photos before printing them.
5 Press the arrow buttons to select a photo printing option, and then press

Note: You can choose to print the most recent photo, print all the photos, print photos that fall within a date
range, print photos by selecting the photo numbers on a proof sheet, or print pre-selected photos from a digital
camera using Digital Print Order Format (DPOF). The DPOF option appears only when there is a valid DPOF file
in your memory device.

6 Adjust the print settings:
• If you are in the Easy Photo menu, then press the arrow buttons to select the paper size and photo size. Press
each time you make a selection.

• If you are in the Print Photos menu, then press the arrow buttons to select the photo size, paper size, paper
type, layout, photo effects, and quality of the photos, and to adjust the brightness and color effects of the
each time you make a selection.
photos. Press

Printing

7 Press the Color/Black button to set a color or black-and-white print.
When you select color or black-only printing, the light near your choice comes on.

8 Press

Note: For best results, allow the prints to dry at least 24 hours before stacking, displaying, or storing.

Printing photos from a memory device using the printer software
1 Load photo paper with the glossy or printable side faceup. (If you are not sure which side is the printable side,
then see the instructions that came with the paper.)

2 From the printer control panel, press

3 Insert a memory card, flash drive, or digital camera set to mass storage mode.
If document files and image files are stored on the memory device, then press the arrow buttons to scroll to
Photos. Press
.

4 Transfer or print the photos:

If the printer is using a USB connection
• Fast Pics launches automatically when you insert the memory device. Follow the instructions on the computer
screen to transfer the photos to the computer or to print.

If the printer is using a Wireless connection (selected models only)
a Press the arrow buttons to scroll to Select Computer, and then press

b Press the arrow buttons to select the network computer where you want to save the photos, and then press
.

c Transfer or print the photos:
• Fast Pics launches on the computer. Follow the instructions on the computer screen to transfer the photos
to the computer or to print.

Printing

Printing photos from a PictBridge-enabled digital camera
PictBridge is a technology available in most digital cameras that lets you print directly from your digital camera
without using a computer.

1 Insert one end of the USB cable into the camera.
Note: Use only the USB cable that came with the camera.

2 Insert the other end of the cable into the PictBridge port on the front of the printer.

Notes:

• Make sure that the PictBridge-enabled digital camera is set to the correct USB mode. If the camera USB
selection is incorrect, then the camera is detected as a flash drive, or an error message will be displayed on
the printer control panel. For more information, see the camera documentation.

• The printer reads only one memory device at a time.
Warning—Potential Damage: Do not touch the USB cable, any network adapter, any connector, or the printer
in the area shown while actively printing from a PictBridge-enabled digital camera. A loss of data can occur.

3 If the PictBridge connection is successful, then the following message appears on the display: PictBridge
Camera detected. Press OK to change settings.

4 Press

to access the PictBridge menu.

Printing

5 Press the arrow buttons to select the paper size, paper type, photo size, and layout of the photos that you want
to print. Press

each time you make a selection.

6 See the documentation for your camera to begin printing.
Note: If you insert the camera while the printer is performing another job, then wait for the job to finish before
printing from the camera.

Printing photos from a memory device using the proof sheet
1 Load letter- or A4-size plain paper.
2 From the printer control panel, press

3 Insert a memory card or flash drive.
4 Press the arrow buttons to scroll to Proof Sheet, and then press

5 Press the arrow buttons to select an option to print a proof sheet.
You can print a proof sheet:

• For all photos on the memory device.
• For the 20 most recent photos, if there are 20 or more photos on the memory device.
• By date, if the photos on the card were taken on different dates. If you choose this option, then press the arrow
buttons to set the start and end dates, and then press

6 Press

to save your selections.

The proof sheet prints.

7 Follow the instructions on the proof sheet to select which photos to print, the number of copies per photo, red-eye
reduction, page layout, print options, and paper size.
Note: When making selections, make sure to fill in the circles completely.

8 Load the proof sheet facedown on the scanner glass.
Scan Proof Sheet appears on the display.
Note: If this option does not appear on the display, then press the arrow buttons until it appears on the display.

9 Press

The printer scans the proof sheet.

10 Load photo paper with the glossy or printable side faceup. (If you are not sure which side is the printable side,
then see the instructions that came with the paper.)
Note: Make sure that the paper matches the size that you selected on the proof sheet.

11 Press the Color/Black button to set a color or black-and-white print.
When you select color or black-only printing, the light near your choice comes on.

12 Press

to print the photos.

Note: To prevent smudging or scratching, avoid touching the printed surface with your fingers or sharp objects. For
best results, remove each printed sheet individually from the paper exit tray, and then allow the prints to dry at least
24 hours before stacking, displaying, or storing.

Printing

Printing photos from a digital camera using DPOF
If your camera supports Digital Print Order Format (DPOF), then you can specify which photos to print, how many of
each, and the print settings while the memory card is still in the camera. The printer recognizes these settings when
you insert the memory card into the printer or connect the camera to the printer.
Note: If you specify a photo size while the memory card is still in the camera, then make sure that the size of the
paper loaded in the printer is not smaller than the size you specify in the DPOF selection.

1 Load photo paper with the glossy or printable side faceup. (If you are not sure which side is the printable side,
then see the instructions that came with the paper.)

2 From the printer control panel, press

3 Insert a memory card.
Memory Card Detected appears on the display.

4 Press the arrow buttons to scroll to Print Photos, and then press
5 Press the arrow buttons to scroll to Print DPOF, and then press

.
to print the photos.

Note: This option appears only if a DPOF file is detected in the memory card.
Note: To prevent smudging or scratching, avoid touching the printed surface with your fingers or sharp objects. For
best results, remove each printed sheet individually from the paper exit tray, and allow the prints to dry at least 24
hours before stacking, displaying, or storing.

Printing from a Bluetooth-enabled device
• This printer is compliant with Bluetooth Specification 2.0. It supports the following profiles: Object Push Profile
(OPP) and Serial Port Profile (SPP). Check with your Bluetooth-enabled device manufacturers (cellular phone or
PDA) to determine their hardware compatibility and interoperability. It is recommended that you use the latest
firmware on your Bluetooth-enabled device.
• To print Microsoft documents from your Windows Mobile/Pocket PC PDA, additional third-party software and
drivers are required. For more information about the required software, see the documentation for your PDA.

Setting up a connection between your printer and a
Bluetooth-enabled device
Note: The printer does not support printing files from your computer using a Bluetooth connection.
You need to set up a connection between a Bluetooth-enabled device and your printer if you are sending a print job
from the Bluetooth device for the first time. You will need to repeat the setup if:

• You reset the printer to its factory default settings.
• You change the Bluetooth security level or the Bluetooth pass key.

Printing

• The Bluetooth-enabled device you are using requires users to set up a Bluetooth connection on every print job.
For more information, see the documentation for your Bluetooth device.

• The name of the Bluetooth device you are using is automatically deleted from the Bluetooth device list.
When the Bluetooth security level is set to High, the printer saves a list of up to eight Bluetooth devices that have
previously set up a connection with the printer. When the printer detects more than eight devices, the least
recently used device is removed from the list. You need to repeat the setup of the deleted device to be able to
send a print job to the printer.
Note: You need to set up a connection for each Bluetooth device that you use to send a print job to the printer.
To set up a connection between the printer and a Bluetooth-enabled device:

1 Insert a USB Bluetooth adapter into the USB port located on the front of the printer.

Bluetooth Dongle Connected appears on the display.
Note: A Bluetooth adapter is not included with the printer.

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Bluetooth Setup, and then press
4 Press the arrow buttons to scroll to Discovery, and then press

5 Make sure Discovery is set to On. If necessary, press the arrow buttons to scroll to On, and then press

The printer is now ready to accept a connection from a Bluetooth-enabled device.

6 Configure the Bluetooth-enabled device to set up a connection to the printer. For more information, see the
documentation for your Bluetooth device.
Note: If the Bluetooth Security Level on the printer is set to High, then you must enter a pass key.

Printing

Setting the Bluetooth security level
1 Insert a Bluetooth USB adapter into the USB port.

Bluetooth Dongle Connected appears on the display.
Note: A Bluetooth adapter is not included with the printer.

2 From the printer control panel, press

3 Press the arrow buttons to scroll to Bluetooth Setup, and then press button
4 Press the arrow buttons to scroll to Security Level, and then press

5 Press the arrow buttons to select the security level, and then press .
• Select Low to allow Bluetooth devices to connect and send print jobs to your printer without requiring users
to enter a pass key.

• Select High to require users to enter a four-digit numeric pass key on the Bluetooth device before connecting
and sending print jobs to the printer.

6 The Bluetooth Pass Key menu appears on the display if you set the security level to High. Use the keypad to enter
your four-digit pass key, and then press

Printing from a Bluetooth-enabled device
Note: The printer does not support printing files from your computer using a Bluetooth connection.

Printing

1 Insert a USB Bluetooth adapter into the USB port.

Bluetooth Dongle Connected appears on the display.
Warning—Potential Damage: Do not touch cables, any network adapter, any connector, the USB Bluetooth
adapter, or the printer in the areas shown while actively printing, reading, or writing from a Bluetooth-enabled
device. A loss of data can occur.
Notes:

• A Bluetooth adapter is not included with the printer.
• Your printer automatically switches to Bluetooth mode when you insert a USB Bluetooth adapter.
2 Make sure the printer is set up to receive Bluetooth connections. For more information, see “Setting up a
connection between your printer and a Bluetooth-enabled device” on page 41.

3 Set up the Bluetooth device to print to the printer. For more information, see the documentation for your
Bluetooth device.

4 See the documentation for your Bluetooth device to begin printing.
Note: If the Bluetooth Security Level on the printer is set to High, you must enter a pass key.

Managing print jobs
Setting your printer as the default printer
Your printer should be selected automatically from the Print dialog when you send a print job. If you have to manually
select your printer, then it is not the default printer.
To set the default printer:

1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.

Printing

3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Set as Default Printer.

Changing the printing mode
To conserve ink, you can change the default printing mode for all print jobs to Quick Print. It uses less ink and is ideal
for printing text-only documents. If you need to change to a different print mode to print photos or other high-quality
documents, then you can select a different mode from the Print dialog before sending the print job.
To change the default print mode:

1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Printing Preferences.
5 Select Quick Print as the printing mode.

Changing the printing mode for a single print job
1 With a document open, click File  Print.
2 Click Properties, Preferences, Options, or Setup.
3 Select Automatic, Quick Print, Normal, or Best.
Note: Printing in Draft mode uses less ink and is ideal for printing text documents.

Pausing print jobs
1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Pause Printing.

Resuming print jobs
1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Open.

Printing

5 Resume the print job:
• If you want to resume a particular print job, then right-click the document name, and then select Resume.
• If you want to resume all print jobs in the queue, then click Printer, and then clear the selection for Pause
Printing.

Canceling print jobs
To cancel a print job from the printer control panel, press

1 Click

. To cancel a print job from the computer, do the following:

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Open.
5 Cancel the print job:
• If you want to cancel a particular print job, then right-click the document name, and then select Cancel.
• If you want to cancel all print jobs in the queue, then click Printer  Cancel All Documents.

Printing

Copying
ADF

Scanner glass

Use the ADF for multiple-page documents.
Note: The ADF is available only on selected models. If you
purchased a printer without an ADF, then load original
documents or photos on the scanner glass.

Use the scanner glass for single pages, small items (such as
postcards or photos), transparencies, photo paper, or thin
media (such as magazine clippings).

Tips for copying
• When using the ADF, adjust the paper guide on the ADF to the width of the original document.
• When using the scanner glass, close the top cover to avoid dark edges on the scanned image.
• Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine
clippings) into the ADF. Place these items on the scanner glass.

Making copies
1 Load paper.
2 Load an original document faceup into the ADF or facedown on the scanner glass.
3 From the printer control panel, press

4 Press the arrow buttons to select the number of copies, and then press the Color/Black button to set a color or
black-and-white copy.
When you select color or black-only printing, the light near your choice comes on.

5 Press

Copying photos
1 Load photo paper with the glossy or printable side faceup. (If you are not sure which side is the printable side,
then see the instructions that came with the paper.)

2 Place a photo facedown on the scanner glass.
Copying

3 From the printer control panel, press
4 Press

until Photo Reprint appears.

5 Press the arrow buttons to scroll to Yes, and then press

6 Press the arrow buttons to select the desired paper size, and then press
7 Press

Note: To prevent smudging or scratching, avoid touching the printed surface with your fingers or sharp objects. For
best results, remove each printed sheet individually from the paper exit tray, and allow the prints to dry at least 24
hours before stacking, displaying, or storing.

Enlarging or reducing images
1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press
4 Press

until Resize appears.

5 Press the arrow buttons until the setting that you want appears.
Notes:

• If you select Custom % Resize, then press
percent value. Press

, and then press the arrow buttons to select the desired custom

to save the setting.

• If you select Borderless, then the printer will reduce or enlarge the document or photo as necessary to print
a borderless copy on the paper size that you selected. For best results with this resize setting, use photo
paper and set the paper type to Photo, or let the printer automatically detect the paper type.

6 Press

Note: After the copy job is finished, press
to reset the settings to the default. The resize setting also switches to
100% after two minutes of printer inactivity.

Adjusting copy quality
1 Load paper.
2 Load an original document faceup into the ADF or facedown on the scanner glass.
3 From the printer control panel, press
4 Press

until Quality appears.

5 Press the arrow buttons to set the copy quality to Automatic, Draft, Normal, or Photo, and then press
your setting.

6 Press

Copying

to save

Making a copy lighter or darker
1 Load paper.
2 Load an original document faceup into the ADF or facedown on the scanner glass.
3 From the printer control panel, press
4 Press

until Lighter/Darker appears.

5 Press the arrow buttons to adjust the slider, and then press

to save your setting.

Note: Pressing the left arrow button makes the copy lighter, and pressing the right arrow button makes the copy
darker.

6 Press

Collating copies using the printer control panel
If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the
copies as groups of pages (not collated).
Collated

Not collated

1 Load paper.
2 Load an original document faceup into the ADF or facedown on the scanner glass.
3 From the printer control panel, press

4 Press the arrow buttons to select the number of copies, and then press
5 Press

until Collate appears.

6 Press the arrow buttons to scroll to On.
7 Press

to save the image to the printer memory.

8 When asked if you want to scan another page, press

to select Yes.

9 Load the next page of the original document faceup into the ADF or facedown on the scanner glass, and then
press

10 Repeat steps 8 and 9 until all the pages that you want to copy have been saved to the printer memory.
11 When asked if you want to scan another page, press the arrow buttons to scroll to No, and then press
printing the copies.

Copying

to start

Repeating an image on one page
You can print the same page image multiple times on one sheet of paper. This option is helpful when creating items
such as labels, decals, flyers, and handouts.

1 Load paper.
2 Load an original document facedown on the scanner glass.
3 From the printer control panel, press
4 Press

until Copies per Sheet appears.

5 Press the arrow buttons to select the number of times that an image is repeated on a page: once, four times, nine
times, or 16 times.

6 Press

Copying multiple pages on one sheet
The Pages per Sheet setting lets you copy multiple pages on one sheet by printing smaller images of each page. For
example, you can condense a 20-page document into five pages if you use this setting to print four page images per
sheet.

1 Load paper.
2 Load an original document faceup into the ADF or facedown on the scanner glass.
3 From the printer control panel, press
4 Press

until Pages per Sheet appears.

5 Press the arrow buttons to select the number of pages that you want to copy on a sheet of paper. You may choose
to copy one, two, or four page images on a sheet.
Note: If you are copying four pages in landscape format, scan pages 3 and 4 first, and then scan pages 1 and 2.

6 Press

to save the image of the page to the printer memory.

7 When asked if you want to scan another page, press

to select Yes.

8 Load the next page of the original document faceup into the ADF or facedown on the scanner glass, and then
press

9 Repeat steps 7 and 8 until all the pages that you want to copy have been saved to the printer memory.
10 When asked if you want to scan another page, press the arrow buttons to scroll to No, and then press
printing.

Making a duplex copy manually
1 Load paper.
2 Load an original document faceup into the ADF or facedown on the scanner glass.
3 From the printer control panel, press

Copying

to start

4 Press the left or right arrow button to select the number of copies, and then press the Color/Black button to set
a color or black-and-white copy.
When you select color or black-only printing, the light near your choice comes on.

5 Press

6 Load the next page of the document.
• If you are copying a one-sided document, then load the next page faceup into the ADF or facedown on the
scanner glass.

• If you are copying a two-sided document, then flip the original document, and then reload it faceup into the
ADF or facedown on the scanner glass.

7 Remove the paper from the paper exit tray, and then reload the paper to print the other side of the document.

8 Press

Canceling copy jobs
To cancel a copy job, press

Scanning stops and the printer returns to the previous menu.

Copying

Scanning
ADF

Scanner glass

Use the ADF for multiple-page documents.
Note: The ADF is available only on selected models. If you
purchased a printer without an ADF, then load original
documents or photos on the scanner glass.

Use the scanner glass for single pages, small items (such as
postcards or photos), transparencies, photo paper, or thin
media (such as magazine clippings).

Tips for scanning
• When using the ADF, adjust the ADF paper guide to the width of the original document.
• When using the scanner glass, close the scanner lid to avoid dark edges on the scanned image.
• Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine
clippings) into the ADF. Place these items on the scanner glass.

• Select the PDF file type if you want to scan multiple pages and save them as one file.

Scanning to a local or network computer
1 Load an original document faceup into the ADF or facedown on the scanner glass.
2 From the printer control panel, press

3 Press the arrow buttons to scroll to Computer or Network, and then press

4 Press the arrow buttons to select the name of a local or network computer, and then press

The local or network computer is the destination that will receive the scan.
Notes:

5 Wait until the printer has finished downloading a list of the scan applications available on the selected computer.
6 Press the arrow buttons to select an application, and then press
Scanning

7 Press the arrow buttons to select the resolution quality and the original image size. Press

each time you make

a selection.

8 Press

to start scanning.

The scan is complete when the application you selected in step 6 opens on the destination computer, and the scan
appears within the application as a new file.

Scanning to a flash drive or memory card
Before you begin, make sure your flash drive or memory card is not write protected.

1 Load an original document faceup into the ADF or facedown on the scanner glass.
2 From the printer control panel, press

3 When Scan to appears on the display, insert the flash drive or memory card.
4 Press the arrow buttons to scroll to USB Flash Drive or Memory Card, and then press

5 Press the arrow buttons to select the resolution quality, the type of output you want to create, and the original
image size. Press

6 Press

each time you make a selection.

to start scanning.

The scan is complete when a message appears on the printer control panel indicating that the file you scanned has
been saved.

Scanning photos into an editing application
Using the printer control panel
1 Load the photo or photos facedown on the scanner glass.
2 From the printer control panel, press

3 Press the arrow buttons to scroll to Computer or Network, and then press

4 Press the arrow buttons to select the name of a local or network computer, and then press

The local or network computer is the destination that will receive the scan.

5 Wait until the printer has finished downloading the list of scan applications available on the selected computer.
6 Press the arrow buttons to select a photo editing application, and then press

7 Press the arrow buttons to select the resolution quality, the type of output you want to create, and the original
image size. Press

8 Press

each time you make a selection.

to start scanning.

9 When asked if you want to scan another page, press

to select Yes.

10 Load the next photo or photos facedown on the scanner glass, and then press

11 Repeat steps 9 and 10 until all the photos that you want to scan are saved to the printer memory.
12 When asked if you want to scan another page, press the arrow buttons to scroll to No, and then press
Scanning

The scan is complete when the photo editing application you selected in step 6 opens on the destination computer,
and the scan appears within the application as a new file.

Using the printer software
1 Load a photo or photos facedown on the scanner glass.
2 Click

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.
4 Select Printer Home.
5 Choose your printer from the printer drop-down list.
6 Click Photo.
• If you want to scan a single photo, or multiple photos as a single image, then select Single photo.
• If you want to scan multiple photos at once and save them as separate images, then select Split into individual
photos.
Scanning starts and the scan progress dialog appears.

7 Save the photo or photos and open in a photo editing application to edit.

Scanning documents into an editing application
An Optical Character Recognition (OCR) application allows you to edit an original text document that has been
scanned. In order for this to work, you must have an OCR application stored on a local or network computer and you
must be able to choose it from the list of applications when you set up the scan.
When selecting settings for the scan:

• Select to scan to the local computer or network computer where the OCR is installed.
• Select to scan to the highest resolution.
1 Load an original document faceup into the ADF or facedown on the scanner glass.
2 Click

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.
4 Select Printer Home.
5 Choose your printer from the printer drop-down list.
6 Click Document.
Scanning starts and the scan progress dialog appears.

7 When the scan is finished, save the document in a word-processing application.
8 Open the document in the selected application to edit it.

Scanning directly to e-mail
1 Load an original document faceup into the ADF or facedown on the scanner glass.
2 Click

or Start.
Scanning

3 Click All Programs or Programs, and then select the printer program folder from the list.
4 Select Printer Home.
5 Choose your printer from the printer drop-down list.
6 Click Email, and then select Photo, Document or PDF.
Scanning starts and the scan progress dialog appears.

7 When the scan is finished, a new e-mail message is created with the scanned document automatically attached.
8 Compose your e-mail message.
Note: If your e-mail program does not open automatically, then you can scan the document to the computer and
then send it through e-mail as an attachment.

Scanning to a PDF
1 Load an original document faceup into the ADF or facedown on the scanner glass.
2 Click

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.
4 Select Printer Home.
5 Choose your printer from the printer drop-down list.
6 Click PDF.
Scanning starts and the scan progress dialog appears.

7 Save the document as a PDF.

Scanning FAQ
How can I improve the quality of a scan?
• Make sure your original documents are in good condition.
• Make sure the application that receives the scanned document is appropriate. For example, if you are scanning
a photo to edit it, then make sure you choose a photo editing application to receive the scan. If you are scanning
a document to edit the text, then make sure you choose an OCR application.
• Use a high resolution.

How do I scan in black and white?
Color is the default for all scans. To scan in black and white, press the Color/Black button on the printer control panel
to switch from color to black and white.

Why am I being asked for a PIN?
PINs are a security measure used to restrict the scanned information from going into certain locations, or to keep
what is being scanned from being seen or used by others. You may be prompted to enter a PIN if the network
computer you are scanning to requires one.
Scanning

To learn how PINs get assigned to network computers, see the Help for the printer software associated with your
operating system.

What is an application list, and how do I update it?
When you scan a file, you can choose which application to use to open it on your computer. The printer downloads
this application list from your computer when scanning for the first time. If you do not see the application you want
on the list, or if you install new applications on your computer, then update the application list in the printer.

Updating the application list
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Computer or Network.
3 Select a local or network computer to receive the scan and then press

4 Select REFRESH from the list of scan applications.
This updates the application list in the printer.

Canceling scan jobs
Press

on the printer control panel, or click Cancel on the computer screen.

Scanning

Faxing
CAUTION—SHOCK HAZARD: Do not use the fax feature during a lightning storm. Do not set up this product
or make any electrical or cabling connections, such as the power supply cord or telephone, during a lightning
storm.

Setting up the printer to fax
Scenario 1: Standard telephone line
Check the scenarios below and follow the setup that is applicable to your telephone line.

Setup 1: Printer is connected to a dedicated fax line

EXT

LINE

EXT

LINE

Tips for this setup:
• You can set the printer to receive faxes automatically (Auto Answer On) or manually (Auto Answer Off).
• If you want to receive faxes automatically (Auto Answer On), then you may set the printer to pick up on any
number of rings that you want.

Faxing

Setup 2: Printer is sharing the line with an answering machine
Connected to the same telephone wall jack

EXT

LINE

PHONE

LINE

EXT

LINE

Connected to different wall jacks

EXT

LINE

EXT
PHONE

LINE

Tips for this setup:
• If you have only one telephone number on your line, or if you do not subscribe to a distinctive ring service, then
you need to set the printer to receive faxes automatically (Auto Answer On).

• Set the printer to pick up calls two rings after the answering machine. For example, if the answering machine
picks up calls after four rings, then set the printer to pick up after six rings. This way, the answering machine picks
up calls first and your voice calls are received. If the call is a fax, then the printer detects the fax signal on the line
and takes over the call.

Faxing

• If you subscribe to a distinctive ring service provided by your telephone company, then make sure that you set
the correct ring pattern for the printer. Otherwise, the printer will not receive faxes even if you have set it to
receive faxes automatically.

Setup 3: Printer is sharing the line with a telephone subscribed to voice mail
service

EXT

LINE

02
EXT

LINE

Tips for this setup:
• This setup works best if you subscribe to a distinctive ring service. If you have distinctive ring service, then make
sure that you set the correct ring pattern for the printer. Otherwise, the printer will not receive faxes even if you
have set it to receive faxes automatically.

• If you have only one telephone number on your line, or if you do not have distinctive ring service, then you need
to set the printer to receive faxes manually (Auto Answer Off).
When you answer the telephone and you hear fax tones, press *9* or the manual answer code on the telephone
to receive the fax.
• You can also set the printer to receive faxes automatically (Auto Answer On), but you need to turn off the voice
mail service when you are expecting a fax. This setting works best if you are using voice mail more often than fax.

Faxing

Scenario 2: Digital Subscriber Line (DSL)
Follow this setup if you have a Digital Subscriber Line (DSL).

EXT

LINE

EXT

LINE

A Digital Subscriber Line splits your regular telephone line into two channels: voice and Internet. Telephone and fax
signals travel through the voice channel, and Internet signals pass through the other channel. This way, you can use
the same line for analog voice calls (including faxing) and digital Internet access.
To minimize interference between the two channels and ensure a quality connection, you need to install a DSL filter
for the analog devices (fax machine, telephone, answering machine) in your network. Interference causes noise and
static on the telephone, failed and poor quality faxes for the printer, and slow Internet connection on your computer.
To install a filter for the printer:

1 Connect the line port of the DSL filter to the wall jack.
2 Connect a telephone cable from the

port on the back of the printer to the phone port on the DSL filter.

3 To continue using a computer for Internet access, connect the computer to the DSL HPN port on the DSL filter.

Faxing

Scenario 3: VoIP telephone service
Follow this setup if you have telephone service from a Voice over Internet Protocol (VoIP) provider.

Tips for this setup:
• Connect the printer to the port labeled Phone Line 1 or Phone Port on the VoIP adapter. The port labeled Phone
Line 2 or Fax Port is not always active. You may need to pay extra to your VoIP provider if you want to activate
the second phone port.

• To make sure that the phone port on the VoIP adapter is active, plug an analog telephone into the phone port,
and then listen for a dial tone. If you hear a dial tone, then the port is active.

• If you need two phone ports for your devices but do not want to pay extra, then do not plug the printer into the
second phone port. You can use a phone splitter. Plug the phone splitter into the Phone Line 1 or Phone
Port , and then plug the printer and telephone into the splitter.
Note: Make sure you use a phone splitter, not a line splitter. To make sure that you are using the correct splitter,
plug an analog telephone into the splitter and then listen for a dial tone.

Faxing

Scenario 4: Digital telephone service through a cable provider
Setup 1: Printer is connected directly to a cable modem
Follow this setup if you normally connect your telephone to a cable modem.

Tips for this setup:
• Connect the printer to the port labeled Phone Line 1 or Phone Port on the cable modem. The port labeled
Phone Line 2 or Fax Port is not always active. You may need to pay extra to your cable provider if you want to
activate the second phone port.

• To make sure that the phone port on the cable modem is active, plug an analog telephone into the phone port,
and then listen for a dial tone. If you hear a dial tone, then the port is active.

Faxing

Setup 2: Printer is connected to a wall jack; cable modem is installed elsewhere
in the house
Follow this setup if your cable provider activated the wall jacks in your house so that you do not have to plug your
devices into the cable modem. Your cable telephone service comes from the wall jacks.

Scenario 5: Country-specific setup
Different countries have different types of telephone wall jacks. The most common wall jack is the Registered Jack-11
(RJ-11), the standard adopted by most countries. You need to have an RJ-11 plug, or a telephone cable that has an
RJ-11 connector, so you can connect a device to an RJ-11 wall jack.

The fax ports on the back of the printer and the telephone cable that comes with the printer have RJ-11 connectors.
If you have a different type of connector in your country or region, then you may need to use an RJ-11 adapter.

Faxing

Connecting the printer to a non-RJ-11 wall jack
To set up the printer for faxing, connect the printer to the RJ-11 adapter that comes with the printer, and then plug
the adapter into the wall jack. You can also connect an additional device (telephone or answering machine) to the
same telephone line. If the additional device does not have an RJ-11 connector, then connect it directly to the wall
port of the printer.
jack. Do not remove the wrap plug from the
Note: The printer may not come with an RJ-11 adapter in your country or region.

EXT

LINE

EXT

LINE

Faxing

If the additional device (telephone or answering machine) has an RJ-11 connector, then you can remove the wrap
port of the printer.
plug and plug the device into the

EXT

LINE

EXT

LINE

Connecting the printer in countries that use serial connection
In some countries or regions, you need to plug all devices into the wall jack. You cannot plug a telephone or answering
port of the printer. This is called serial connection.
machine into the
Austria

Germany

Portugal

Belgium

Ireland

Spain

Denmark

Italy

Sweden

France

Netherlands

Switzerland

Finland

Norway

United Kingdom

Warning—Potential Damage: If your country is on the list, then do not remove the wrap plug from the
the printer. It is necessary for the proper functioning of the devices on the telephone line.

Faxing

port of

EXT

LINE

EXT

LINE

Connecting the printer to a wall jack in Germany
The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering machines.
The F port is for telephones.

N F N

Faxing

Connect the printer to any of the N ports.

EXT

LINE

N F N

EXT
PHONE

LINE

Entering your user information
Your user information includes your name or your company name, your fax number (your fax number is your
telephone number, unless you have a dedicated fax telephone line), and the time and date on your fax machine
when a transmission is made. This information appears in the header and footer of the faxes that you send.
In some countries, you cannot send a fax without this information. Some fax machines also block faxes without sender
information, so make sure that you enter this information in your printer.

Setting the fax header
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Dialing and Sending, and then press
4 Press

again to select Your Fax Name.

5 Use the keypad to enter your name or your company name, and then press
6 Press the arrow buttons to scroll to Your Fax Number, and then press

.
.

7 Use the keypad to enter your fax number or your telephone number, and then press

Setting the fax footer
1 Press

2 Press the arrow buttons to scroll to Fax Printing, and then press
3 Press the arrow buttons to scroll to Fax Footer, and then press
Faxing

.
.

4 Press

again to select On.

5 During the initial setup of your printer, you were prompted to enter the date and time. If you have not entered
this information, then do the following:

a Press

twice.

b Press the arrow buttons to scroll to Device Setup, and then press
c Press the arrow buttons to scroll to Date/Time, and then press
d Enter the date using the keypad, and then press
e Enter the time using the keypad, and then press

.
.

Configuring the fax settings
You can configure the fax settings through the printer control panel or the fax software. If you configure the fax
settings in the printer control panel, then the fax software imports those settings. The changes appear the next time
you launch the fax software. The printer also saves the settings that you choose in the fax software, unless you set
the printer to block changes made from the computer.

Configuring fax settings using the fax software
Before opening the fax software to configure the fax settings, make sure that:

• The printer is properly connected to the telephone line.
• The printer is turned on and connected to the computer.
• The printer is not in Power Saver mode. If the printer is in Power Saver mode, then press
1 Click

to wake up the printer.

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Click Printer Home.
4 Click the Fax tab, and then click Set up the printer to fax.
The Printer Setup Wizard opens.

5 Run the Printer Setup Wizard. Make sure you select the correct telephone service and connection. The wizard
configures optimal fax settings based on your connection.
Note: If you want to configure the advanced fax settings, then click Configure the advanced settings in the Fax tab
of the Printer Home. This launches the Fax Setup Utility.
For more information, click Help or

to view the help information for the fax software.

Configuring fax settings using the printer control panel
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

Faxing

3 Configure the fax settings using the selections in the menu:
From here

You can

Address Book

Set up, view, or print the Address Book.

Reports

• Print activity logs. Activity logs let you view the sent and
received fax history of your printer.

• Print confirmation pages or transmission reports. These reports
let you know if the faxes that you send are sent successfully.
Ringing and Answering

• Set the printer to receive faxes automatically or manually. Turn
Auto Answer to On or Off.

• Adjust the ringing volume.
• Set the number of rings. This is important if you choose to
receive faxes automatically (Auto Answer On).

• Set the distinctive ring. If you subscribe to the distinctive ring
feature on your telephone line, then set the correct pattern for
the printer in this menu.

• Enable fax forwarding.
• Set a manual answer code. This is the code you press to receive
faxes manually.

• Set the Caller ID pattern that you want. Some countries or
regions have multiple patterns.
Fax Printing

• Set the printer to print incoming faxes to fit a page.
• Set the fax footer.

Dialing and Sending

• Set your fax name and fax number.
• Adjust the dialing volume.
• Set the dial method, redial time, number of redial attempts,
dialing prefix, and fax sending speed.

• Convert sent faxes into modes that receiving fax machines
recognize. Otherwise, such faxes are aborted.

• Enable error correction during transmission.
• Set whether the printer scans the original document before or
after dialing the recipient.
Set the printer to scan before dialing so that you do not have
to scan the document again if the fax fails. The scanned
document is saved in the printer memory. The printer can then
retrieve it and automatically redial the number.
If you set the printer to scan after dialing, then the printer does
not automatically redial, even when the phone line is busy.
Fax Blocking

Block unwanted incoming faxes.

Faxing

Creating a contact list
You can create a contact list using the Address Book in the printer control panel or the phone book in the fax software.
If you create a contact list in the printer control panel, then the fax software automatically saves those contacts as
Speed Dial entries. Likewise, when you add contacts to the Speed Dial list of the fax software, the printer automatically
saves them to the printer Address Book.
You can save up to 89 contacts and 10 fax groups in the contact list.

Creating a contact list using the fax software
1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Click Printer Home.
4 Click the Fax tab, and then click Edit contact list.
The Contacts tab of the Printer Setup Utility opens.

5 Click Select from phonebook.
6 From the Phonebook field, choose a phone book.
7 Select the contact that you want to add, and then click Add to or change list to import the contact.
Note: To add contacts, you need to import contacts from the phone books on your computer that are supported
by the fax software. In addition to the software Address Book, you may also have phone books of the mail clients
installed on your computer, such as Microsoft Outlook.

8 Click OK.
For more information, click Help or

to view the help information for the fax software.

Creating a contact list using the printer control panel
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press
3 Press

again to select Address Book.

4 To add a fax number to your Address Book:
a Press the arrow buttons to scroll to Add.
b Press

c Press

again to select the Speed Dial number.

Note: Numbers 1 to 89 are for individual contacts. Numbers 90 to 99 are for group contacts. When you send
a fax, you can enter the Speed Dial number instead of the fax number of your contact.

d Use the keypad to enter the fax number in the Enter Number field, and then press .
e Use the keypad to enter the contact name in the Enter Name field, and then press to save the entry.
f Repeat steps 4b through 4e to add additional entries as needed. You can enter up to 89 fax numbers.

Faxing

5 To add a fax group:
a Press to select Add.
b Using the keypad, enter any number from 90 to 99, and then press

c Enter a fax number in the Enter Number field, and then press .
d If you want to add another contact to the group, press the arrow buttons to scroll to Yes, and then press
.

e Repeat step 5d as necessary. You can enter up to 30 fax numbers for the group.
If you do not want to add another fax number, then press

to select No.

f Enter the group name in the Enter Name field, and then press

to save the entry.

Sending faxes
ADF

Scanner glass

Use the ADF for multiple-page documents.
Note: The ADF is available only on selected models. If you
purchased a printer without an ADF, load original
documents or photos on the scanner glass.

Use the scanner glass for single pages, small items (such as
postcards or photos), transparencies, photo paper, or thin
media (such as magazine clippings).

Tips for sending faxes
Before you send a fax:

• Make sure that the printer is on and connected to a working telephone, DSL, or VoIP line. The line is working if
you hear a dial tone.
• Load an original document faceup into the ADF or facedown on the scanner glass.

• When using the ADF, adjust the paper guide on the ADF to the width of the original document.
• When using the scanner glass, close the top cover to avoid dark edges on the scanned image.

Sending faxes using the printer control panel
1 From the printer control panel, press

2 Enter a fax number, or press Address Book to select a number from the Speed Dial or Group Dial list.

Faxing

3 If you want to send a fax to a single recipient, then press

If you want to send a fax to a group of numbers (broadcast fax), press the arrow buttons to scroll to Yes, and
then press .

4 Press the Color/Black button to select a color or black-and-white fax.
5 Press

to start the fax job.

Warning—Potential Damage: Do not touch the cables or the

and

ports while actively sending a fax.

Tip:
• You can send a broadcast fax to up to 30 recipients.

Sending faxes using the computer
1 With a document open, click File  Print.
2 From the Printer Name menu, select the fax version of your printer, and then click OK.
The Send Fax Wizard appears.

3 Follow the instructions on the computer screen.

Receiving faxes
Tips for receiving faxes
When receiving faxes:

• Make sure that the printer is on and connected to a working telephone, DSL, or VoIP line. The line is working if
you hear a dial tone.
• If you set the printer to receive faxes manually (Auto Answer Off), then make sure that the ringer volume is not
set to Off.

• If you have set the printer to receive faxes automatically (Auto Answer On), then load paper in the printer.

Receiving faxes automatically
1 Make sure that Auto Answer is on:
a From the printer control panel, press .
b Press the arrow buttons to scroll to Fax Setup, and then press

c Press the arrow buttons to scroll to Ringing and Answering, and then press
d Press

again to select Auto Answer.

e If Auto Answer is not set to On, press the arrow buttons to scroll to On, and then press
2 Set the number of rings before the printer picks up incoming faxes:
a Press the arrow buttons to scroll to Pick Up On, and then press

b Press the arrow buttons to scroll to the number of rings that you want, and then press

Faxing

to save the setting.

When the number of rings you set is detected, the printer automatically receives the incoming fax.
Warning—Potential Damage: Do not touch the cables or the

and

ports while actively receiving a fax.

Tips:
• If the printer is sharing the line with other analog devices (telephone, answering machine), then set the printer
to pick up calls two rings after the answering machine. For example, if the answering machine picks up calls after
four rings, then set the printer to pick up after six rings. This way, the answering machine picks up calls first and
your voice calls are received. If the call is a fax, then the printer detects the fax signal on the line and takes over
the call. If the printer is on a dedicated fax line, then you may set the printer to pick up on any number of rings.

• If you have multiple numbers on a single line, or if you subscribe to a distinctive ring service provided by your
telephone company, then make sure that you set the correct ring pattern for the printer. Otherwise, the printer
will not receive faxes even if you have set it to receive faxes automatically.

Receiving a fax manually
1 Turn off Auto Answer:
a From the printer control panel, press .
b Press the arrow buttons to scroll to Fax Setup, and then press

c Press the arrow buttons to scroll to Ringing and Answering, and then press
d Press

again to select Auto Answer.

e Press the arrow buttons to scroll to Off, and then press

2 When the telephone rings and you hear fax tones when you pick up the handset, press

on the printer or *9*

on the telephone attached to the printer.
Warning—Potential Damage: Do not touch the cables or the

and

ports while actively receiving a fax.

Tips:
• The default code for answering faxes manually is *9*, but for increased security, you can change it to a number
that only you know. You can enter up to 7 characters for your code. The valid characters are the digits 0-9 and
the characters # and *.

• Make sure that the telephone is plugged into the
connected to the wall jack through the

port on the back of the printer and that the printer is

port.

Faxing FAQ
If I skipped the fax setup initially, do I need to run the installer again
to set up the fax?
You do not need to run the installer again. You can set up and configure the fax through the fax software that was
installed with the printer software.

Faxing

To set up the fax:

1 Connect the printer to the telephone line. For more information, see “Setting up the printer to fax” on page 57.
2 Configure the fax settings using the fax software. To access the fax software:
a Click or Start.
b Click All Programs or Programs, and then select the printer program folder from the list.
c Click Printer Home.
The Printer Home opens.

d Click the Fax tab, and then click Set up the printer to fax.
The Printer Setup Wizard opens.

e Run the Printer Setup Wizard. Make sure you select the correct telephone service and connection. The wizard
configures optimal fax settings based on your connection.

What is a splitter and what type of splitter should I use?
If there are limited wall jacks in your home or limited ports on your adapter, then you can use a phone splitter. A
splitter splits the telephone signal and allows you to connect multiple devices to the wall jack. It has two or more
ports where you can plug the devices. Do not use a line splitter.
To make sure that you are using the correct splitter, plug an analog telephone into the splitter and then listen for a
dial tone.

What is my fax number?
In most cases, your telephone number is also your fax number. If you subscribe to the Distinctive Ring Pattern
Detection (DRPD) service offered by telephone companies, then your fax number is the number that you assigned
to the printer. Make sure that you enter the correct distinctive ring pattern for that number in the fax software or in
the Fax Setup menu of the printer control panel.
If you have more than one telephone line, then make sure that you enter the number for the line on which the printer
is connected.

What is my dialing prefix?
The dialing prefix is the number or series of numbers that you press before you can dial the actual fax number or
telephone number. If the printer is an office setting or in a private branch exchange, this can be a specific number
that you need to press so you can make a call outside the office. This can also be a country code or an area code that
you need to enter if you are sending faxes outside of town. This can be very useful if you frequently send faxes to the
same country or area. When you set the dialing prefix in the utility, you do not need to press the number or series of
numbers every time you dial the fax number or telephone number. The printer automatically inputs the prefix every
time you dial.
You can enter up to 8 characters as your dialing prefix. The valid characters are the numbers 0-9 and the characters
# and *. If you are using the fax software to enter the dial prefix, then you may also include the characters period,
comma, star, pound, plus, minus, and parenthesis.

When do I need to set Auto Answer to On?
Set Auto Answer to On if you want the printer to receive faxes automatically.

Faxing

If the printer is connected to the same telephone line with an answering machine, then you must set Auto Answer
to On so that you can receive both your voice calls and your faxes. Make sure that the answering machine is set to
pick up on fewer rings than the rings set in the printer. This lets the other devices pick up the voice calls first. If an
incoming call is a fax, the printer can detect fax signals on the line and takes the call.

How many rings should I set?
If the printer is sharing a line with an answering machine, then set the printer to pick up on the greater number of
rings. Because you have only one line, there is no way of distinguishing a voice call from an incoming fax. You can
set the number of rings so that the answering machine takes the voice calls and the printer takes the incoming faxes.
If you set the other devices to pick up on fewer rings, then the devices pick up calls first, and your voice calls are
received. If a call is a fax, then the printer can detect it and will take over the call.
If the printer is on a dedicated fax line, then you may set the printer to pick up on any number of rings that you want.

How do I set the distinctive ring for the printer?
Setting the correct ring is important if you subscribe to the Distinctive Ring Pattern Detection (DRPD) feature offered
by telephone companies. This feature allows you to have multiple telephone numbers on one telephone line. Each
telephone number has a designated ring pattern (a single ring, a double ring, a triple ring). The different ring patterns
let you know what telephone number was dialed, and what device you should use to answer the call.
Assign one of your telephone numbers to the printer as the fax number, and then set the printer to answer the ring
pattern of that number. If the pattern is set incorrectly, then the printer rings, but it never receives the fax.
To set the ring pattern in the printer:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Ringing and Answering, and then press
4 Press the arrow buttons to scroll to Ring Pattern, and then press

5 Press the arrow buttons to select the ring pattern for the printer, and then press

Distinctive Ring is also called Ident-a-Call, Smart Ring, Teen Ring, RingMaster, and IdentaRing.

How can I check the dial tone?
A dial tone lets you know if the telephone line is working or if the printer is properly connected to the telephone line.
If you encounter problems sending and receiving faxes, then make sure you can hear a dial tone on the line and
through the printer.

Make sure the telephone line and the wall jack are working
1 Plug an analog telephone into the wall jack.
2 Listen for a dial tone through the telephone handset.
If you hear a dial tone, then the telephone line and the wall jack are working.
If you do not hear a dial tone, plug the analog telephone into a second wall jack, and then listen for a dial tone.
If you hear a dial tone, then the telephone line is working but the first wall jack is not working.

Faxing

Make sure the printer is connected properly to the telephone line
1 While the printer is connected to a telephone line through the
telephone into the

port on the back of the printer, plug an analog

port of the printer.

2 Listen for a dial tone.
If you hear a dial tone, then the telephone line is working and properly connected to the printer.
If you do not hear a dial tone through both the wall jack and the printer, then see the “Fax troubleshooting checklist”
on page 112.

How do I adjust the speaker volume on the printer?
Listen to the dial tone to check if the telephone line is working and to check if the cables and devices are connected
properly in your telephone network. Make sure that the dialing volume is not set to Off, especially if you are dialing
a number on hook. If you set the printer to receive faxes manually, then make sure that you set the ringer volume
loud enough for you to hear it.

Adjusting the dialing volume
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Dialing and Sending, and then press
4 Press the arrow buttons to scroll to Dial Volume, and then press

5 Press the arrow buttons to select a dial volume setting, and then press

Adjusting the ringer volume
1 Press

to scroll back to the Fax Setup menu, and then press

2 Press the arrow buttons to scroll to Ringing and Answering, and then press
3 Press the arrow buttons to scroll to Ringer Volume, and then press
4 Press the arrow buttons to select a ringer volume setting, and then press

.
.

How can I make sure that the fax answers the call before the
answering machine?
To make sure the printer picks up incoming faxes, set Auto Answer to On, and then set the printer to pick up after a
greater number of rings than the answering machine. For example, if the answering machine picks up calls after four
rings, then set the printer to pick up after five rings. This way, the answering machine picks up calls first and your
voice calls are received. If the call is a fax, then the printer detects the fax signal on the line and takes over the call.

What settings work best with digital voice mail?
Voice mail and fax can share the same telephone line if you subscribe to a distinctive ring service. This feature allows
you to have multiple telephone numbers on one telephone line. Each telephone number has a designated ring
pattern (a single ring, a double ring, a triple ring). The different ring patterns let you know which telephone number
was dialed, and which device you should use to answer the call.

Faxing

If you do not have distinctive ring service, then set the printer to receive faxes manually (Auto Answer Off). This setting
lets you receive both voice calls and fax calls, but works best if you use voice mail more often. You need to turn off
voice mail whenever you are expecting a fax.

How do I change the resolution of the documents that I fax?
The resolution, or fax quality, of the documents that you send may affect fax transmission. The receiving fax machine
may not support high resolutions and may not be able to receive your fax. You can fix this by enabling Auto Fax
Conversion, but the automatic conversion may result in an unreadable fax, especially if the original document is
already blurred.
Choose a fax quality that best suits the capacity of the receiving fax machine and the quality of the original document.
Quality

Black resolution

Color resolution

Standard

200 x 100

200 x 200

Fine

200 x 200

Superfine

300 x 300

200 x 200

Ultrafine

300 x 300 (half-toned)

200 x 200

When sending a fax, after entering the fax number, press the arrow buttons to select a fax quality, and then
press .

How do I send a fax at a scheduled time?
1 From the printer control panel, press

2 Enter the fax number of the recipient, or press Address Book to select a number from the Speed Dial or Group
Dial list.

3 If you want to send the fax to a single recipient, then press

If you want to send a fax to a group of numbers (broadcast fax), then press the arrow buttons to scroll to Yes,
and then press .

4 Press

to scroll to Schedule Fax.

5 Press the arrow buttons to scroll to Send Later, and then press
6 Enter the time you want to send the fax, and then press
7 Press

to start scanning the document.

8 If the printer is not set to the 24-hour mode, press the arrow buttons to select AM or PM, and then press
9 Press

to save the scheduled fax.

The printer sends the fax at the designated time. Do not turn off the printer or unplug it from the telephone line
before the scheduled time.

How do I send a fax using a phone calling card?
1 Press Dialtone.
You should hear the dial tone of the telephone line.

2 Enter the calling card information, and then when you are connected to the telephone carrier, follow the prompts.
Faxing

3 When prompted, enter the fax number of the recipient, and then press

How do I know that the fax was sent successfully?
You can set the printer to print a confirmation page, or transmission report, every time you send a fax. This report
includes the date and time that the fax was sent. If the fax job is unsuccessful, then the report also includes the cause
of the error.

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press
3 Press the arrow buttons to scroll to Reports, and then press

.
.

4 Press the arrow buttons to scroll to Confirmation, and then press

5 Press the arrow buttons to select a report printing option:
• If you want to print a report every time you send a fax, then select For All or Print for All.
• If you want to save on ink and print a report only when a fax job is unsuccessful, then select On Error.
6 Press

How do I view the fax history of the printer?
You can print reports of sent and/or received faxes.

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press
3 Press the arrow buttons to scroll to Reports, and then press
4 Press

.
.

again.

5 To set when to print fax activity reports, press the arrow buttons to choose whether to print the fax activity reports
after 40 faxes or on request only.

6 To print fax activity reports, press the arrow buttons to scroll to Print Reports, and then press .
• To print sent and received fax history, press the arrow buttons to scroll to Activity Report, and then
press

• To print sent fax history only, press the arrow buttons to scroll to Send Log, and then press .
• To print received fax history only, press the arrow buttons to scroll to Receive Log, and then press

How do I forward a fax?
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Ringing and Answering, and then press
4 Press the arrow buttons to scroll to Fax Forward, and then press

5 Press the arrow buttons to scroll to Forward or Print & Forward, and then press

6 Using the keypad, enter the number to which you want to forward the fax, and then press
Faxing

When you enable this option, all the faxes that you receive are automatically forwarded until you disable it.
To disable fax forwarding, return to the Fax Forward menu, and then select Off.

Can I block faxes?
You can block faxes from specific numbers. You can also block junk faxes and faxes from unidentified senders (senders
without a Caller ID). This feature is helpful if you want to receive faxes automatically but want to filter the faxes that
you receive.

1 Turn on fax blocking.
a From the printer control panel, press

b Press the arrow buttons to scroll to Fax Setup, and then press

c Press the arrow buttons to scroll to Fax Blocking, and then press
d Press the arrow buttons to scroll to Turn On/Off, and then press
e Press the arrow buttons to scroll to On, and then press

.
.

to save the setting.

2 Add a number to block.
a Press the arrow buttons to scroll to Add.
b Press

c Use the keypad to enter the fax number, and then press to save.
d Use the keypad to enter the name of the person that you want to block.
e Repeat steps 2b through 2d until you have added all the numbers that you want to block. You can block up
to 50 numbers.

3 Block unidentified faxes (faxes without a Caller ID number).
a Press the arrow buttons to scroll to Block No-ID, and then press
b Press the arrow buttons to scroll to On, and then press

to save the setting.

Can I retrieve failed faxes?
The printer saves an incoming fax to the printer memory before it prints the fax. If the printer runs out of ink or runs
out of paper, then you can print the fax later after resolving the error. The printer prompts you if there are faxes to
be printed.
If an incoming fax or an outgoing fax fails due to power loss, then the printer automatically prints an error report the
next time it is turned on. For incoming faxes, the error report lets you know who sent the fax and how many pages
were not printed. For outgoing faxes, it lets you know how many pages were not sent. Faxes lost due to power loss
are not retrievable.

Faxing

Networking
Installing the printer on a wireless network
Wireless network compatibility
Your printer contains an IEEE 802.11g wireless print server. Your printer is compatible with IEEE 802.11 b/g/n routers
that are Wi-Fi certified. If you are having issues with an n router, verify with your router manufacturer that the current
mode setting is compatible with g devices, as this setting varies depending on the router brand/model.

Supported network security options
The printer supports three wireless security options: no security, WEP, and WPA/WPA2.

No Security
It is not recommended to use no security at all on a home wireless network. Using no security means that anyone
within range of your wireless network can use your network resources—including Internet access, if your wireless
network is connected to the Internet. The range of your wireless network may extend far beyond the walls of your
home, allowing access to your network from the street or from your neighbors’ homes.

WEP
WEP (Wireless Equivalent Privacy) is the most basic and the weakest type of wireless security. WEP security relies on
a series of characters called the WEP key.
Every device on the wireless network must use the same WEP key. WEP security can be used on both ad hoc and
infrastructure networks.
A valid WEP key has:
• Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9
or

• Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, punctuation, and symbols found on a
keyboard.

WPA/WPA2
WPA (Wi-Fi Protected Access) and WPA2 (Wi-Fi Protected Access 2) offer stronger wireless network security than WEP.
WPA and WPA2 are similar types of security. WPA2 uses a more complex encryption method and is more secure than
WPA. Both WPA and WPA2 use a series of characters, called the WPA pre-shared key or passphrase, to protect wireless
networks from unauthorized access.
A valid WPA passphrase has:

• From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.
or

• Exactly 64 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

Networking

Every device on the wireless network must use the same WPA passphrase. WPA security is an option only on
infrastructure networks with wireless access points and network cards that support WPA. Most newer wireless
network equipment also offers WPA2 security as an option.
Note: If your network uses WPA or WPA2 security, then select WPA Personal when you are prompted to select the
type of security your network uses.

Printing a network setup page
A network setup page lists the configuration settings of the printer, including the IP address and MAC address of the
printer.

1 Load plain paper.
2 From the printer control panel, press

3 Press the arrow buttons to scroll to Network Setup, and then press

Print Network Setup Page appears.

4 Press

to print the network setup page.

Information you will need to set up the printer on a wireless
network
To set up the printer for wireless printing, you need to know:
• The name of your wireless network. This is also known as the Service Set Identifier (SSID).

• If encryption was used to secure your network.
• The security key (either a WEP key or WPA passphrase) that allows other devices to communicate on the network
if encryption was used to secure your network.
You can locate your network WEP key or WPA passphrase by accessing your wireless access point or router and
checking the security information.
If your wireless access point (wireless router) is using Wired Equivalent Privacy (WEP) security, the WEP key should be:

• Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.
or

• Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, punctuation, and symbols found on a
keyboard.
If your wireless access point is using Wi-Fi Protected Access (WPA) security, the WPA passphrase should be:
• From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.
or

• Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
If your wireless network is not using security, then you will not have a security key.
Note: If you do not know the SSID of the network that your computer is connected to, launch the wireless utility of
the computer network adapter and look for the network name. If you cannot find the SSID or the security information
for your network, see the documentation that came with the wireless access point, or contact your system support
person.

Networking

Installing the printer on a wireless network
Before you install the printer on a wireless network, make sure that:

• Your wireless network is set up and working properly.
• The computer you are using is connected to the same wireless network where you want to set up the printer.
1 Close all open software programs.
2 Insert the installation software CD.
If the Welcome screen does not appear after a minute, then launch the CD manually:

a Click , or click Start and then click Run.
b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
3 Follow the instructions on the Welcome screen to set up the printer.

Installing the printer on other computers
Once the printer is set up on the wireless network, it can be accessed wirelessly by any other computer on the network.
However, you will need to install the printer driver on every computer that will access it. You do not need to configure
the printer again, although you will need to run the setup software on each computer to install the driver.

1 Close all open software programs.
2 Insert the installation software CD.
If the Welcome screen does not appear after a minute, then launch the CD manually:

a Click , or click Start and then click Run.
b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
3 Follow the instructions on the computer screen for installing a configured printer on a new computer.

Interpreting the colors of the Wi-Fi indicator light
The colors of the Wi-Fi indicator light show the network status of the printer.

• Off means one of the following:
– The printer is turned off or is powering up.
– The printer is not connected to a wireless network and is in Power Saver mode. In Power Saver mode, the
power light pulses on and off.
• Solid orange means one of the following:

– The printer has not yet been configured for a wireless network.
– The printer is configured for an ad hoc connection, but it is not currently communicating with another ad hoc
device.

• Blinking orange means one of the following:
– The printer is out of the range of the wireless access point (wireless router).
– The printer is trying to communicate with the wireless access point, but the wireless access point is turned
off or not working properly.

– Either the configured printer or the wireless access point has been turned off and back on, and the printer is
trying to establish communications with the network.

– The wireless settings of the printer may no longer be valid.
• Green means that the printer is connected to a wireless network and is ready for use.
Networking

Special wireless installation instructions
The following instructions apply to customers outside of North America who are using a wireless broadband box.
Some examples of these boxes include LiveBox, AliceBox, N9UF Box, FreeBox, and Club Internet.

Before you begin
• Make sure your box is wireless-enabled and activated to work on a wireless network. For more information about
configuring the box to work wirelessly, see the documentation that came with your box.

• Make sure your box is turned on and that your computer is on and connected to your wireless network.

Adding the printer to your wireless network
1 Set up your printer for wireless networking using the setup instructions provided.
Stop when you are prompted to select a network.

2 If there is an association/registration button on the back of your box, press it before selecting a network.
Note: After pressing the association/registration button, you have five minutes to complete the printer
installation.

3 Return to the computer screen.
From the list that appears in the “Choose your wireless network” dialog, select your network, and then click
Continue.
If your wireless network does not appear in the list:

a Select Unlisted Network, and then click Continue.
b Enter the details about your wireless network.
Note: Your WEP, WPA, or WPA2 key may be obtained from the bottom of the box, the user’s guide that came
with the box, or from the box Web page. If you have already changed the key for your wireless network, use
the key you created.

4 Follow the instructions on your screen to complete installation.

Assigning a static IP address
The printer will be assigned an IP address automatically through DHCP on most wireless networks.
If you want to assign a static IP address to your printer, do the following:

1 Complete the wireless setup, allowing the printer to receive a DHCP address from a DHCP server on the network.
2 Print a network setup page to see what IP address is currently assigned to the printer.
3 Open a Web browser and then type the printer IP address in the address field. Press Enter.
The printer Web page loads.

4 Click the Configuration link.
5 Click the TCP/IP link.
6 Click the Set Static IP Address link.

Networking

7 Type the IP address you want to assign to the printer in the IP Address field.
8 Click the Submit button.
The Submitting Selection message appears.
To confirm that the address was successfully assigned, type the static IP address in the Web browser address field
and then press Enter. The printer Web page loads if the address was successfully assigned.
For more information, contact your system support person.

Changing wireless settings after installation
To change wireless settings on the printer, such as the configured network, the security key, or other settings, do the
following:

1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 Click the Settings tab.
5 Click the Wireless setup utility link.
6 Follow the instructions on the computer screen to configure the printer for wireless access with the new settings.

Advanced wireless setup
Creating an ad hoc wireless network
The recommended way to set up your wireless network is to use a wireless access point (wireless router). A network
set up this way is called an infrastructure network. If you have an infrastructure network, you should configure the
printer for use on that network.
Note: The printer can communicate on only one wireless network at a time. Configuring the printer for an ad hoc
wireless network will keep it from working on any other wireless network, either ad hoc or infrastructure.
You can set up an ad hoc network if you:

• Do not have an access point or wireless router
• Do not already have a wireless network (but do have a wireless adapter for your computer)
• Want to set up a standalone network between the printer and a computer with a wireless network adapter

In Windows Vista
1 Click

2 Click Control Panel.
3 Click Network and Internet.
4 Under Network and Sharing Center, click Connect to a Network.
5 In the Connect to a Network dialog, click Set up a wireless ad-hoc (computer-to-computer) network, and then
click Next.

Networking

6 Follow the instructions in the “Set up a wireless ad hoc network” wizard. As part of the setup:
a Create a network name or SSID for the network between the computer and your printer.
b Write down the name of your network. Be sure to use the exact spelling and capitalization.
c Go to the Security Type list, select WEP, and then create a WEP key.
WEP keys must be:

• Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A-F, a–f, and 0-9.
or

• Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard
d Write down the password for your network. Be sure to use the exact spelling and capitalization.
Windows Vista will enable the ad hoc network for you. It will appear in the “Connect to a network” dialog under
“Available networks,” indicating that the computer is configured for the ad hoc network.

7 Close the Windows Control Panel and any remaining windows.
8 Insert the installation software CD, and follow the directions for wireless installation.
Note: Do not connect the installation or network cables until instructed to do so by the setup software.

9 When the available networks are displayed, provide the network name and the security information you created
in step 6. The installer will configure the printer for use with your computer.

10 Store a copy of your network name and security information in a safe place for future reference.

In Windows XP
1 Click Start.
2 Click Control Panel.
3 Click Network and Internet Connections.
4 Click Network Connections.
5 Right-click the icon for your wireless network connection.
6 Click Enable, if it appears in the pop-up menu.
Note: If Disable appears, your wireless connection is already enabled.

7 Right-click the Wireless Network Connection icon.
8 Click Properties.
9 Click the Wireless Networks tab.
Note: If the Wireless Networks tab does not appear, your computer has third-party software that controls your
wireless settings. You must use that software to set up the ad hoc wireless network. For more information, see
the documentation for the third-party software to learn how to create an ad hoc network.

10 Select the Use Windows to configure my wireless network settings check box.
11 Under Preferred Networks, delete any existing networks.
a Select the network to be removed.
b Click Remove to delete the network from the list.
12 Click Add to create an ad hoc network.
Networking

13 In the Network Name (SSID) box, type the name you want to give your wireless network.
14 Write down the network name you chose so you can refer to it when running the wireless setup. Be sure to use
the exact spelling and capitalization.

15 If Network Authentication appears in the list, select Open.
16 In the “Data encryption” list, select WEP.
17 If necessary, clear the “The key is provided for me automatically” check box.
18 In the Network Key box, type in a WEP key.
19 Write down the WEP key you chose so you can refer to it when running the wireless setup. Make sure you copy
it down exactly, including any capital letters.

20 In the “Confirm network key” box, type the same WEP key.
21 Select This is a computer-to-computer (ad hoc) network; wireless access points are not used.
22 Click OK twice to close the two open windows.
23 It may take a few minutes for your computer to recognize the new settings. To check on the status of your network:
a Right-click the Wireless Network Connections icon.
b Select View Available Wireless Networks.
• If the network is listed but the computer is not connected, select the ad hoc network and then click
Connect.

• If the network does not appear, wait a minute and then click Refresh network list.
24 Insert the installation software CD, and follow the directions for wireless installation.
Note: Do not connect the installation or network cables until instructed to do so by the setup software.

25 When the available networks are displayed, provide the network name and the security information you created
beginning in step 13. The installer will configure the printer for use with your computer.

26 Store a copy of your network name and security information in a safe place for future reference.

In Windows 2000
• Refer to the documentation that came with your wireless network adapter for information on configuring an ad
hoc network with Windows 2000.

Adding a printer to an existing ad hoc wireless network
Note: The printer can communicate on only one wireless network at a time. Configuring the printer for an ad hoc
wireless network will remove it from any other wireless network, either ad hoc or infrastructure, for which it is
configured.

1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 Click the Settings tab.
5 Click Wireless setup utility link.
6 Follow the instructions on the computer screen.
Networking

Configuring the printer wirelessly using WPS (Wi-Fi Protected
Setup)
Wi-Fi Protected Setup (WPS) is a method of configuring computers and printers on a secure wireless network. WPS is
faster and eliminates typing errors when new devices are added to a wireless network. The SSID and WPA passphrase
are automatically detected and configured for you. The printer supports WPS and can be configured for a wireless
access using WPS. In order to use WPS to configure the printer, the wireless router must also support WPS.
If you want to use WPS to set up your printer, then insert the CD and follow the instructions on the computer screen.
Note: To use WPS to configure the printer wirelessly, all of the devices on your wireless network must support WPS.
If any device on your network does not support WPS, then you must type the SSID and security information when
prompted.

Switching between USB and wireless connections (Windows only)
You can change the way you access your printer, depending on your needs. The following procedures assume that
you have configured your printer for one type of connection and that the printer drivers are installed on the computer.
See related topics on troubleshooting specific connection types if you encounter difficulties during configuration.

Using the printer wirelessly
1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 Click the Settings tab.
5 Click the Wireless setup utility link.
6 Follow the instructions on the computer screen to set up the printer wirelessly.
Note: There is no need to remove the USB cable connecting the printer to the computer during wireless configuration.

Using the printer locally (USB)
1 Attach a USB cable to the computer and to the printer.
2 Wait a moment for Windows to locate the driver and finish setting up the printer.
Note: You can continue to use the printer wirelessly.

Sharing a printer in a Windows environment
1 Prepare the computers to share the printer:
a Make all computers printing to the printer accessible through Network Neighborhood by enabling File and
Print Sharing. See the Windows documentation for instructions on enabling File and Print Sharing.

b Install the printer software on all computers that will print to the printer.
2 Identify the printer:
a On the computer that is attached to the printer, do one of the following:
1 Click , or click Start and then click Run.
2 In the Start Search or Run box, type control printers.
Networking

3 Press Enter, or click OK.
The printer folder opens.

b
c
d
e

Right-click the name of your printer.
Click Sharing.
From the Sharing tab, select Share this printer or Shared as, and then assign a distinctive name.
Click OK.

3 Locate the printer from the remote computer:
Note: The remote computer is the one that is not attached to the printer.

a Do one of the following:
1 Click , or click Start and then click Run.
2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

b
c
d
e
f

Right-click the name of your printer.
Click Properties.
Click the Ports tab, and then click Add Port.
Select Local Port, and then click New Port.
Type the Universal Naming Convention (UNC) Port name, which consists of the server name and the
distinctive printer name that was specified in step 2 on page 87. The name should be in the form \\server
\printer.

g Click OK.
h Click Close on the Printer Ports dialog.
i Make sure the new port is selected on the Ports tab, and then click Apply.
The new port is listed with the printer name.

j Click OK.

Networking FAQ
What is Wi-Fi Protected Setup?
Wi-Fi Protected Setup (WPS) is a product certification that provides simple and secure configuration. WPS assists
users in establishing wireless home networks and enabling network security without requiring prior knowledge of
Wi-Fi technology. WPS configures the network name (SSID) and WPA passphrase for network devices. WPS only
supports networks that communicate through access points or routers and is not applicable in ad hoc networks.
We support the following methods in adding new wireless network devices:

• Personal Identification Number (PIN)—A PIN from the new device is entered into the access point.
• Push Button Configuration (PBC)—The user pushes a button on both the access point and the new device.

Networking

Look for any of these identifier marks to check if your device is WPS certified:

You can find these WPS logos on the side, back, or top of your access point or router.

Where do I find my WEP key or WPA passphrase?
To find the WEP key or WPA passphrase for the wireless network, view the security settings on the access point or
wireless router. Most access points have a Web page that can be accessed using a Web browser.
You can also check the manual that came with your access point or router. If your access point or router is using the
default settings, you can find the information in the manual. If someone else set up your network for you, that person
or company may have included the information in the manual.
If you do not know how to access the Web page, or if you do not have administrator access to the wireless access
point on your network, and are unable to locate the information in the manual, contact your system support person.

What is an SSID?
A Service Set Identifier (SSID) is the name that identifies a wireless network. All devices on the network must know
the SSID of the wireless network or they will not be able to communicate with each other. Usually, the wireless network
broadcasts the SSID to allow wireless devices in the area to connect to it. Sometimes, the SSID is not broadcast for
security reasons.
If the SSID of your wireless network is not broadcast, it cannot be detected automatically and will not show up in the
list of available wireless networks. You must enter the network information manually in this situation.
An SSID can contain up to 32 alphanumeric characters.

Where do I find my SSID?
You can find the SSID for the wireless network by viewing the settings on the access point or wireless router. Most
access points have a built-in Web server that can be accessed using a Web browser.
Many network adapters provide a software application that allows you to view the wireless settings of your computer,
including your SSID. Check your computer to see if a program was installed with your network adapter.
If you are unable to locate your SSID using either of these methods, contact your system support person.

What is a network?
A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers
connected together for communication through cables or through a wireless connection. A network can be wired,
wireless, or designed to have both wired and wireless devices.
Devices on a wired network use cables to communicate with each other.
Devices on a wireless network use radio waves instead of cables to communicate with each other. For a device to be
able to communicate wirelessly, it must have a wireless network adapter attached or installed that lets it receive and
transmit radio waves.

Networking

How do I find out what type of security my network is using?
You must know the WEP key or WPA passphrase and the type of security (WEP, WPA, or WPA2) used on the wireless
network. To obtain this information, see the documentation that came with your wireless access point (wireless
router), see the Web page associated with the wireless access point, or consult your system support person.
Note: The WEP key or WPA passphrase is not the same as the password for the wireless access point. The password
allows you to access the wireless access point settings. The WEP key or WPA passphrase allows printers and computers
to join your wireless network.

How are home networks configured?
For desktop computers, laptops, and printers to communicate with each other over a network, they must be
connected by cables and/or have wireless network adapters built in or installed in them.
There are many different ways a network can be set up. Four common examples appear below.
Note: The printers in the following diagrams represent printers with internal print servers built into them so that
they can communicate over a network.

Wireless network examples
Scenario 1: Mixed wired and wireless connections on a network with Internet access
• All computers and printers connect to the network through a router with Ethernet and wireless capabilities.
• Some computers and printers connect wirelessly to the router; others connect over a wired connection.
• The network is connected to the Internet through a DSL or cable modem.
Internet

Networking

Scenario 2: Wireless network with Internet access
• All computers and printers connect to the network using a wireless access point or wireless router.
• The wireless access point connects the network to the Internet through a DSL or cable modem.
Internet

Scenario 3: Wireless network with no Internet access
• Computers and printers connect to the network using a wireless access point.
• The network has no connection to the Internet.

Scenario 4: Computer connected wirelessly to a printer without Internet access
• A computer is directly connected to a printer without going through a wireless router.
• This configuration is referred to as an ad hoc network.
• The network has no connection to the Internet.

Note: Most computers can connect to only one wireless network at a time. If you access the Internet over a wireless
connection, you will lose Internet access if you are connected to an ad hoc network.

Why do I need an installation cable?
When setting up the printer on your wireless network, the printer will need to temporarily connect to a computer
using the installation cable. This temporary connection is used to set up the wireless settings of the printer.

Networking

The installation cable connects to a rectangular USB port on the installing computer and the square USB port on the
printer.

How do I attach the installation cable?
The installation cable attaches to a USB port on the computer and to the square connector on the back of the printer.
This connection allows you to configure the printer for a networked or locally attached installation.

1 Attach the large, rectangular connector to any USB port on your computer. USB ports may be on the front or the
back of the computer, and may be horizontal or vertical.

2 Attach the small, square connector to the printer.

3 Continue following the on-screen instructions.

How are infrastructure and ad hoc networks different?
Wireless networks can operate in one of two modes: infrastructure or ad hoc.

Networking

In infrastructure mode, all devices on a wireless network communicate with each other through a wireless router
(wireless access point). Devices on the wireless network must have valid IP addresses for the current network and
share the same SSID and channel as the wireless access point.
In ad hoc mode, a computer with a wireless network adapter communicates directly with a printer equipped with a
wireless print server. The computer must have a valid IP address for the current network and be set to ad hoc mode.
The wireless print server must be configured to use the same SSID and channel that the computer is using.
The following table compares the characteristics and requirements of the two types of wireless networks.
Infrastructure

Ad hoc

Communication

Through wireless access point

Directly between devices

Security

More security options

WEP or no security

Range

Determined by range and number of Restricted to range of individual
wireless access points
devices on network

Speed

Usually faster

Usually slower

Unique IP address for each device

Yes

Mode set to

Infrastructure mode

Ad hoc mode

Same SSID

Yes, including the wireless access
point

Yes

Same channel

Yes, including the wireless access
point

Yes

Characteristics

Requirements for all devices

We recommend setting up a network in infrastructure mode using the installation CD that came with the printer.
Infrastructure mode is the recommended setup method because it provides:
• Increased network security

• Increased reliability
• Faster performance
• Easier setup

Finding the signal strength
Wireless devices have built-in antennas that transmit and receive radio signals. The signal strength listed on the
printer network setup page indicates how strongly a transmitted signal is being received. Many factors can affect
the signal strength. One factor is interference from other wireless devices or other devices such as microwave ovens.
Another factor is distance. The farther two wireless devices are from each other, the more likely it is that the
communication signal will be weaker.
The strength of the signal received by your computer can also affect the connectivity of the printer with the network
during configuration. When you installed the wireless adapter in your computer, the adapter software probably
placed an icon in your system tray. Try double-clicking this icon, and it will tell you how strongly the computer is
receiving the wireless signal from the network.
To improve signal quality, remove sources of interference and/or move wireless devices closer to the wireless access
point (wireless router).

Networking

How can I improve wireless signal strength?
A common reason wireless printers fail to communicate over a network is poor wireless signal quality. If the signal
is too weak, too distorted, or blocked by an object, it cannot carry information between the access point and the
printer. To determine if the printer is receiving a strong signal from the access point, print a network setup page. The
Quality field indicates the relative strength of the wireless signal the printer is receiving. Drops in signal strength can
be intermittent, however, and although the signal quality appears high, it may drop during certain conditions.
If you think signal strength is a problem between your access point and the printer, try one or more of the following:
Notes:

• The solutions below are for infrastructure networks. If you are using an ad hoc network, adjust the computer
when the solution suggests adjusting the access point.

• Ad hoc networks have a much shorter range than infrastructure networks. Try moving the printer closer to the
computer if they seem to have trouble communicating.

MOVE THE PRINTER CLOSER TO THE WIRELESS ACCESS POINT/WIRELESS ROUTER
If the printer is too far away from the access point, it will not be able to communicate with other devices on the
network. For most indoor wireless networks, the maximum distance between the access point and the printer is
approximately 100 feet (30 meters). This distance could be longer or shorter, depending upon the layout of the
network and the limitations of the access point.

REMOVE OBSTACLES BETWEEN THE ACCESS POINT AND THE PRINTER
The wireless signal from your access point will pass through most objects. Most walls, floors, furniture and other
objects will not block the wireless signal. However, there are materials that are too dense for the signal to pass
through. Objects containing metal and concrete can block the signal. Arrange your printer and access point so
that the signal is not blocked by such objects.

REMOVE SOURCES OF INTERFERENCE
Other types of radio frequencies can cause problems with the wireless signal on your network. These sources of
interference can cause printing issues that seem to come and go. Turn off potential sources of interference where
possible. Avoid using microwaves and cordless phones when printing over your wireless network.
If another wireless network is operating in the vicinity, change the wireless channel on the access point.
Do not place your access point on a printer or other electronic device. Such devices can also interfere with the
wireless signal.

ARRANGE THE NETWORK TO REDUCE SIGNAL ABSORPTION
Even when the wireless signal is able to pass through an object, it is slightly weakened. If it passes through too
many objects, it can be significantly weakened. All objects absorb part of the wireless signal when it passes through
them, and certain types of objects absorb enough to cause communications problems. Place your access point as
high in the room as possible to avoid signal absorption.

Networking

How can I make sure my computer and printer are connected to the
same wireless network?
If the printer is not on the same wireless network as the computer, you will not be able to print wirelessly. The SSID
of the printer must match the SSID of the computer, if the computer is already connected to the wireless network.

1 Obtain the SSID of the network that the computer is connected to:
a Type the IP address of your wireless access point (wireless router) into the address field of your Web browser.
If you do not know the IP address of the wireless access point:
1 Click , or click Start and then click Run.
2 In the Start Search or Run box, type cmd.
3 Press Enter, or click OK.
The Command Prompt window opens.
4 Type ipconfig, and then press Enter. Check the Wireless Network Connection section:

• The “Default Gateway” entry is typically the wireless access point.
• The IP address appears as four sets of numbers separated by periods, such as 192.168.2.134.
b
c
d
e

Type the user name and password of the router when prompted.
Click OK.
On the main page, click Wireless or any other selection where settings are stored. The SSID will be displayed.
Write down the SSID.
Note: Make sure you copy it exactly, including any capital letters.

2 Print the printer network setup page.
In the Wireless section, look for SSID.

3 Compare the SSID of the computer and SSID of the printer.
If the SSIDs are the same, then the computer and the printer are connected to the same wireless network.
If the SSIDs are not the same, then run the utility again to set up the printer on the wireless network used by the
computer.

Can I use my printer on a USB and a network connection at the same
time?
Yes, the printer supports a simultaneous USB and network connection. The printer can be configured in the following
ways:
• Locally attached (connected to a computer using a USB cable)

• Wireless network
• Wireless network and locally attached simultaneously

What is a MAC address?
A Media Access Control (MAC) address is a 48-bit identifier associated with the hardware of network equipment. The
MAC address may also be called the physical address because it is connected to the hardware of a device instead of
its software. The MAC address is displayed as a hexadecimal number in this format: 01-23-45-67-89-AB.
Every device capable of communicating on a network has a MAC address. Network printers, computers, and routers,
whether Ethernet or wireless, all have MAC addresses.
Networking

While it is possible to change the MAC address of a network device, it is not common practice to do so. For this reason,
MAC addresses are considered permanent. IP addresses are easily changed, so MAC addresses are a more reliable
method of identifying a specific device on a network.
Routers with security capabilities may allow filtering of MAC addresses on networks. This allows a managed list of
devices to access the network, identified by their MAC addresses. MAC address filtering can help prevent access on
the network from unwanted devices, such as from intruders on a wireless network. MAC address filtering can also
prevent legitimate access if you forget to add a new device to the router's list of allowed addresses. If your network
uses MAC address filtering, be sure to add the MAC address of the printer to the list of allowed devices.

How do I find the MAC address?
Most network equipment has a unique hardware identification number to distinguish it from other devices on the
network. This is called the Media Access Control (MAC) address.
When installing the printer on a network, make sure you select the printer with the correct MAC address.
The MAC address label is located inside the printer.

MAC:
XX
XX
XX
XX
XX
XX

The MAC address of the internal print server is a series of letters and numbers. Other devices sometimes use a type
of MAC address called Universally Administered Address (UAA).
MAC:

XX XX XX XX XX XX

UAA:

XX XX XX XX XX XX

Note: A list of MAC addresses can be set on an access point (router) so that only devices with matching MAC addresses
are allowed to operate on the network. This is called MAC filtering. If MAC filtering is enabled in your access point and
you want to add a printer to your network, then the MAC address of the printer must be included in the MAC filter
list.

What is an IP address?
An IP address is a unique number used by devices (such as a wireless printer, computer, or wireless access point) on
an IP network to locate and communicate with each other. Devices on an IP network can communicate with each
other only if they have unique and valid IP addresses. A unique IP address means no two devices on the same network
have the same IP address.
An IP address is a group of four numbers separated by periods. An example of an IP address is 192.168.100.110.

Networking

What is TCP/IP?
Networks are able to function because computers, printers, and other devices are able to send data to each other,
either through cables or by using wireless signals. This transfer of data is made possible by sets of data transmission
rules called protocols. A protocol can be thought of as a language, and like a language, it has rules allowing participants
to communicate with each other.
Different types of networks use different protocols, but Transmission Control Protocol/Internet Protocol (TCP/IP) is the
most popular. TCP/IP is used to send data over the Internet as well as over most corporate and home networks.
Because computers do not understand words and instead rely upon numbers for communication, TCP/IP requires
that every device on a network using TCP/IP to communicate must have an IP address. IP addresses are essentially
unique computer names in a numeric format, used to transfer data around a network. IP addresses allow TCP/IP to
confirm requests for and receipt of data by various devices on the network.

How do I locate IP addresses?
1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type cmd.
3 Press Enter, or click OK.
The Command Prompt window opens.

4 Type ipconfig, and then press Enter.
The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.

How to locate a printer IP address
• You can locate the printer IP address by viewing the printer network setup page.

How are IP addresses assigned?
An IP address may be assigned automatically by the network using DHCP. Once the printer is set up on a computer,
the computer sends all print jobs across the network to the printer using this address.
If the IP address is not automatically assigned, you will be asked during wireless setup to manually enter an address
and other network information after selecting your printer from the available list.

What is a key index?
A wireless access point (wireless router) can be configured with as many as four WEP keys. Only one key is used on
the network at a time, however. The keys are numbered, and the number of a key is referred to as its key index. All
devices on the wireless network must be configured to use the same key index when multiple WEP keys are configured
on the wireless access point.
Select the same key index on your printer as you are using on your wireless access point.

Networking

Maintaining the printer
Maintaining ink cartridges
Checking ink levels
Using the printer control panel
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Maintenance, and then press
3 Press

again to select Ink Levels.

4 Press the arrow buttons to check the ink level in each cartridge.

Using the printer software
1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 Choose your printer from the printer drop-down list.
5 From the Maintenance tab, click Check ink levels.

Aligning the printhead
If the characters or lines on your printer image appear jagged or wavy, then you may need to align the printhead.

Using the printer control panel
1 Load plain paper.
2 From the printer control panel, press

3 Press the arrow buttons to scroll to Maintenance, and then press
4 Press the arrow buttons to scroll to Align Printer, and then press
5 Press

.
.

again.

An alignment page prints.
Note: Do not remove the alignment page until printing is finished.

Using the printer software
1 Load plain paper.
2 Click

or Start.

3 Click All Programs or Programs, and then select the printer program folder from the list.
Maintaining the printer

4 Select Printer Home.
5 Choose your printer from the printer drop-down list.
6 From the Maintenance tab, click Align cartridges.
7 Follow the instructions on the computer screen.
If you aligned the cartridges to improve print quality, then print your document again. If print quality has not
improved, then clean the printhead nozzles.

Cleaning the printhead nozzles
Poor print quality is sometimes due to clogged printhead nozzles. Clean the printhead nozzles to improve the quality
of your prints.
Notes:

• Cleaning the printhead nozzles uses ink, so clean them only when necessary.
• Deep cleaning uses more ink, so try the Clean Printhead option first to save ink.
• If the ink levels are too low, you must replace the ink cartridges before you can clean the printhead nozzles.

Using the printer control panel
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Maintenance, and then press

3 Press the arrow buttons to scroll to Clean Printhead or Deep Clean Printhead, and then press
4 Press

to clean the printhead nozzles.

A cleaning page prints.

Using the printer software
1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 From the Maintenance tab, click Clean Cartridges.

Cleaning the exterior of the printer
1 Make sure that the printer is turned off and unplugged from the wall outlet.
CAUTION—SHOCK HAZARD: To avoid the risk of electric shock when cleaning the exterior of the printer,
unplug the power cord from the wall outlet and disconnect all cables to the printer before proceeding.

2 Remove paper from the paper support and paper exit tray.
3 Dampen a clean, lint-free cloth with water.
Warning—Potential Damage: Do not use household cleaners or detergents, as they may damage the finish of
the printer.

Maintaining the printer

4 Wipe only the outside of the printer, making sure to remove any ink residue that has accumulated on the paper
exit tray.
Warning—Potential Damage: Using a damp cloth to clean the interior may cause damage to your printer.

5 Make sure the paper support and paper exit tray are dry before beginning a new print job.

Cleaning the scanner glass
1 Dampen a clean, lint-free cloth with water.
2 Gently wipe the scanner glass clean.
Note: Make sure all ink or corrective fluid on a document is dry before placing the document on the scanner glass.

Maintaining the printer

100

Troubleshooting
Before you troubleshoot
Use this checklist to solve most printer problems:

•
•
•
•
•
•
•
•
•

Make sure the power cord is plugged into the printer and into a properly grounded electrical outlet.
Make sure the printer is not plugged into any surge protectors, uninterrupted power supplies, or extension cords.
Make sure the printer is turned on.
Make sure the printer is securely connected to the host computer, print server, or other network access point.
Check the printer for error messages, and resolve any errors.
Check for paper jam messages, and clear any jams.
Check the ink cartridges, and install new cartridges if necessary.
Use the Service Center to locate and solve the problem (Windows only).
Turn the printer off, wait about 10 seconds, and then turn the printer back on.

Using the Service Center to solve printer problems
The Service Center provides step-by-step troubleshooting help and contains links to printer maintenance tasks and
customer support.
To open the Service Center, use one of these methods:
Method 1

Method 2

If it appears on an error message dialog, click the For
additional assistance, use the Service Center link.

1 Click or Start.
2 Click All Programs or Programs, and then select the
printer program folder from the list.

3 Select Printer Home.
4 From the Support tab, select Service Center.

If Troubleshooting does not solve your problem
Visit our Web site at support.dell.com to find the following:

• Live online technical support
• Contact numbers for telephone technical support

Setup troubleshooting
•
•
•
•

“Incorrect language appears on the display” on page 102
“Printhead error” on page 102
“Software did not install” on page 103
“Print job does not print or is missing pages” on page 104
Troubleshooting

101

•
•
•
•

“Printer is printing blank pages” on page 105
“Printer is busy or does not respond” on page 105
“Cannot delete documents from the print queue” on page 106
“Cannot print through USB” on page 106

Incorrect language appears on the display
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

CHANGE THE LANGUAGE USING THE PRINTER MENUS
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Defaults, and then press

3 Press the arrow buttons to scroll to Set Defaults, and then press
4 Press the arrow buttons to scroll to Use Factory, and then press

.
.

5 Complete the initial printer setup.

CHANGE THE LANGUAGE USING A BUTTON COMBINATION (IF YOU CANNOT READ THE CURRENT
LANGUAGE)
1 Turn the printer off.
2 Press and hold down

and

, and then press

to turn the printer on.

The printer resets and starts the initial printer setup.

3 Complete the initial printer setup.

Printhead error
If the "Before you troubleshoot" checklist does not solve the problem, then try the following:

REMOVE AND REINSERT THE PRINTHEAD
1 Open the printer and lift the latch.

Troubleshooting

102

2 Remove the printhead.

3 Wipe the printhead contacts using a clean, lint-free cloth.

4 Reinsert the printhead.

Note: If removing and reinserting the printhead does not resolve the error, then contact technical support.

Software did not install
If you encountered problems while installing, or if your printer does not appear in the list in the Printers folder or as
a printer option when sending a print job, then try removing and reinstalling the software.
Before you reinstall the software, do the following:

MAKE SURE THAT YOUR COMPUTER MEETS THE MINIMUM SYSTEM REQUIREMENTS LISTED ON
THE PRINTER BOX

TEMPORARILY DISABLE SECURITY PROGRAMS IN WINDOWS BEFORE INSTALLING THE SOFTWARE
Troubleshooting

103

CHECK THE USB CONNECTION
1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.
2 Firmly plug the square end of the USB cable into the back of the printer.
3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.
The USB port is marked with a

USB symbol.

RECONNECT THE PRINTER POWER SUPPLY
1 Turn off the printer, and then unplug the power cord from the wall outlet.
2 Gently remove the power supply from the printer, and then reinsert it.
3 Plug the power cord into the wall outlet, and then turn on the printer.

Print job does not print or is missing pages
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAKE SURE THE INK CARTRIDGES ARE INSERTED CORRECTLY
1 Turn the printer on, and then open the printer.
2 Make sure the cartridges are inserted correctly.
The cartridges should click firmly into the matching color slot of the printhead.

3 Close the printer.

SELECT YOUR PRINTER FROM THE PRINT DIALOG BEFORE SENDING THE PRINT JOB
MAKE SURE THE PRINT JOB IS NOT PAUSED
MAKE SURE YOUR PRINTER IS SET AS THE DEFAULT PRINTER
RECONNECT THE PRINTER POWER SUPPLY
1 Turn off the printer, and then unplug the power cord from the wall outlet.
2 Gently remove the power supply from the printer, and then reinsert it.
3 Plug the power cord into the wall outlet, and then turn on the printer.

REMOVE AND RECONNECT THE USB CABLE CONNECTED TO YOUR PRINTER
CHECK THE USB CONNECTION
1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.
2 Firmly plug the square end of the USB cable into the back of the printer.

Troubleshooting

104

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.
The USB port is marked with a

USB symbol.

REMOVE AND REINSTALL THE PRINTER SOFTWARE
Printer is printing blank pages
Blank pages may be caused by improperly installed ink cartridges.

REINSTALL THE INK CARTRIDGES AND DEEP CLEAN AND ALIGN THE PRINTHEAD
1 Reinstall the ink cartridges, see “Replacing ink cartridges” on page 13 for more information.
If the cartridges do not seem to fit, make sure the printhead is properly seated, and then try installing the
cartridges again.

2 Load plain paper.
3 From the printer control panel, press

4 Press the arrow buttons to scroll to Maintenance, and then press

5 Press the arrow buttons to scroll to Deep Clean Printhead, and then press

A cleaning page prints.

6 Press the arrow buttons to scroll to Align Printer, and the press

An alignment page prints.
Note: Do not remove the alignment page until printing is finished.

Printer is busy or does not respond
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAKE SURE THE PRINTER IS NOT IN POWER SAVER MODE
If the power light is blinking on and off slowly, then the printer is in Power Saver mode. Press
printer.

to wake up the

If the printer will not come out of Power Saver mode, then reset the power:

1 Unplug the power cord from the wall outlet, and then wait 10 seconds.
2 Insert the power cord into the wall outlet, and then turn on the printer.
If this problem persists, then check our Web site for updates for your printer software or firmware.

Troubleshooting

105

Cannot delete documents from the print queue
If you have jobs stuck in the print queue and cannot delete them to get other jobs to print, then the computer and
printer may not be communicating.

RESTART THE COMPUTER AND TRY AGAIN
Cannot print through USB
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

USB symbol.

MAKE SURE THE USB PORT IS ENABLED IN WINDOWS
1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type devmgmt.msc.
3 Press Enter, or click OK.
The Device Manager opens.

4 Click the plus sign (+) beside Universal Serial Bus controllers.
If USB Host Controller and USB Root Hub are listed, then the USB port is enabled.
For more information, see the computer documentation.

REMOVE AND REINSTALL THE PRINTER SOFTWARE

Jams and misfeeds troubleshooting
•
•
•
•

“Paper jam in the printer” on page 106
“Paper jam in the paper support” on page 107
“Paper jam in the ADF (selected models only)” on page 107
“Paper or specialty media misfeeds” on page 108

Paper jam in the printer
Note: The parts inside the printer are sensitive. Avoid unnecessarily touching these parts while clearing jams.

Troubleshooting

106

1 Press

to turn off the printer.

2 Check the paper tray or lift the scanner unit to check for jammed paper.

3 Firmly grasp the paper, and then gently pull it out.
Note: Be careful not to tear the paper while removing it.

4 Press

to turn the printer back on.

Paper jam in the paper support
Note: The parts inside the printer are sensitive. Avoid unnecessarily touching these parts while clearing jams.

1 Press

to turn off the printer.

2 Firmly grasp the paper, and then gently pull it out.
Note: Be careful not to tear the paper while removing it.

3 Press

to turn the printer back on.

Paper jam in the ADF (selected models only)
1 Press the button, and lift the ADF door.

Troubleshooting

107

2 Firmly grasp the paper, and gently pull it out.
3 Close the ADF door.
4 Press

Paper or specialty media misfeeds
These are possible solutions if paper or specialty media misfeeds or skews, or if multiple sheets feed or stick together.
Try one or more of the following:

CHECK PAPER CONDITION
Use only new, unwrinkled paper.

CHECK PAPER LOADING
• Load a smaller amount of paper into the printer.
• Load paper with the print side faceup. (If you are not sure which side is the printable side, see the instructions
that came with the paper.)

• Check the loading instructions for your paper or specialty media.

REMOVE EACH PAGE AS IT IS PRINTED
ADJUST THE PAPER GUIDES TO FIT THE LOADED PAPER

Print troubleshooting
•
•
•
•

“Poor quality at the edges of the page” on page 108
“Streaks or lines on printed image” on page 109
“Print speed is slow” on page 109
“Computer slows down when printing” on page 110

Poor quality at the edges of the page
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

CHECK MINIMUM PRINT SETTINGS
Unless you are using the borderless feature, use these minimum print margin settings:

• Left and right margins:
– 6.35 mm (0.25 in.) for letter-size paper
– 3.37 mm (0.133 in.) for all paper sizes except letter
• Top margin: 1.7 mm (0.067 in.)
• Bottom margin: 12.7 mm (0.5 in.)

Troubleshooting

108

SELECT THE BORDERLESS PRINT FEATURE
1 With a document or photo open, click File  Print.
2 Click Properties, Preferences, Options, or Setup.
3 From the Paper Options section of the Print Setup tab, select Borderless.

Streaks or lines on printed image
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

CHECK THE INK LEVELS
Replace low or empty ink cartridges.

SELECT A HIGHER PRINT QUALITY FROM THE PRINTER SOFTWARE
MAKE SURE THE INK CARTRIDGES ARE PROPERLY INSTALLED
ALIGN THE PRINTHEAD
CLEAN OR DEEP CLEAN THE PRINTHEAD NOZZLES
Note: If these solutions do not remove the streaks or lines on the printed image, then contact technical support.

Print speed is slow
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAXIMIZE COMPUTER PROCESSING SPEED
• Close all applications not in use.
• Minimize the number and size of graphics and images in the document.
• Remove as many unused fonts as possible from your system.

ADD MEMORY
Consider purchasing more RAM.

SELECT A LOWER PRINT QUALITY FROM THE PRINTER SOFTWARE
MANUALLY SELECT A PAPER TYPE THAT MATCHES THE TYPE OF PAPER YOU ARE USING
REMOVE AND REINSTALL THE PRINTER SOFTWARE

Troubleshooting

109

Computer slows down when printing
These are possible solutions. Try one of the following:

IF YOU ARE USING A USB CONNECTION, THEN TRY A DIFFERENT USB CABLE
IF YOU ARE ON A NETWORK, THEN RESET THE POWER OF THE ACCESS POINT (ROUTER)
1 Unplug the power cord from the access point.
2 Wait ten seconds, and then insert the power cord.

Copy and scan troubleshooting
•
•
•
•
•
•
•

“Copier or scanner does not respond” on page 110
“Scanner unit does not close” on page 110
“Poor copy or scanned image quality” on page 110
“Partial copies or scans of documents or photos” on page 111
“Scan was not successful” on page 111
“Scanning takes too long or freezes the computer” on page 111
“Cannot scan to a computer over a network” on page 111

Copier or scanner does not respond
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

SET YOUR PRINTER AS THE DEFAULT PRINTER
REMOVE AND REINSTALL THE PRINTER SOFTWARE
Scanner unit does not close
1 Lift the scanner unit.
2 Remove any obstruction keeping the scanner unit open.
3 Lower the scanner unit.

Poor copy or scanned image quality
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

CLEAN THE SCANNER GLASS
ADJUST THE SCAN QUALITY FROM THE PRINTER SOFTWARE
REVIEW THE TIPS FOR COPYING, SCANNING, AND IMPROVING PRINT QUALITY
Troubleshooting

110

USE A CLEARER VERSION OF THE ORIGINAL DOCUMENT OR IMAGE
MAKE SURE THE DOCUMENT OR PHOTO IS LOADED FACEDOWN ON THE SCANNER GLASS AND IN
THE CORRECT CORNER

Partial copies or scans of documents or photos
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAKE SURE THE DOCUMENT OR PHOTO IS LOADED FACEDOWN ON THE SCANNER GLASS AND IN
THE CORRECT CORNER

SELECT A PAPER SIZE FROM THE PRINTER SOFTWARE THAT MATCHES THE LOADED PAPER
MAKE SURE THE ORIGINAL SIZE SETTING MATCHES THE SIZE OF THE DOCUMENT YOU ARE SCANNING
Scan was not successful
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

USB symbol.

RESTART THE COMPUTER
Scanning takes too long or freezes the computer
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

CLOSE OTHER SOFTWARE PROGRAMS THAT ARE NOT BEING USED
USE A LOWER SCANNING RESOLUTION
Cannot scan to a computer over a network
If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the following:

MAKE SURE THE PRINTER AND THE DESTINATION COMPUTER ARE CONNECTED TO THE SAME
NETWORK

Troubleshooting

111

MAKE SURE THE PRINTER SOFTWARE IS INSTALLED ON THE DESTINATION COMPUTER

Fax troubleshooting
•
•
•
•
•

“Fax troubleshooting checklist” on page 112
“Cannot send faxes” on page 113
“Cannot receive faxes” on page 115
“Cannot run the fax software” on page 116
“Fax error messages on the printer control panel” on page 116

For detailed descriptions of common terms and tasks, see the following:

• “Setting up the printer to fax” on page 57
• “Faxing FAQ” on page 73

Fax troubleshooting checklist
If you encounter problems sending and receiving faxes, then check the connection first:

1 Check for a dial tone on the telephone line by plugging an analog telephone into the wall jack, DSL filter, VoIP
device, or cable modem where you connected the printer. Make sure you plug the telephone into the same port.
If you do not hear a dial tone, then contact your line provider.

2 While the printer is connected to the telephone line, check for a dial tone by plugging an analog telephone into
the

port of the printer.

If you do not hear a dial tone, then use the checklist below. Listen for a dial tone after checking each item.
If you hear a dial tone but still have problems sending and receiving faxes, then see the other topics in this section.

Connection checklist
• Make sure that the printer and other devices on the line (if applicable) are set up and configured correctly
according to your setup scenario.

• Make sure that the cables are connected to the correct ports.
• Make sure that the cables are securely plugged in.
Check the cable connections for the following hardware, if applicable:
Power supply Answering machine Cable modem Splitter
Telephone

VoIP adapter

DSL filter

RJ-11 adapter

• If the printer is connected to a Digital Subscriber Line, then make sure you are using a DSL filter for the printer.
• If the printer is connected to a VoIP adapter or cable modem, then make sure that the printer is plugged into the
first phone port.

• If you are using a splitter, then make sure that you are using a phone splitter. Do not use a line splitter.

Troubleshooting

112

Cannot send faxes
If the “Fax troubleshooting checklist” does not solve the problem, then try one or more of the following:

MAKE SURE THAT YOU HAVE REGISTERED YOUR USER INFORMATION IN THE PRINTER
If you did not enter your user information during initial setup, then enter your fax name and fax number. In some
countries, you cannot send a fax without entering your fax name or company name. Some fax machines also block
unknown faxes or faxes without sender information.

DECREASE THE TRANSMISSION SPEED OF THE FAX MODEM
The modem of the printer can transmit data at 33,600 bps. This is the maximum speed at which the printer can
send and receive faxes. It is not necessary, however, to set the modem to its fastest transmission capability. The
speed of the modem of the receiving fax machine must match or be greater than the speed at which you are
sending your fax. Otherwise, your fax will not be received.
To decrease the transmission speed of the modem:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Dialing and Sending, and then press
4 Press the arrow buttons to scroll to Max Send Speed, and then press
5 Select a sending speed, and then press

SET THE PRINTER TO SCAN THE ORIGINAL DOCUMENT BEFORE DIALING THE NUMBER
The printer does not automatically redial if you set it to scan the original document after dialing the number.
Set the printer to scan before dialing so that you do not have to scan the document again if the fax fails. The scanned
document is saved in the printer memory. The printer can then retrieve it and automatically redial the number.
To set the printer to scan before dialing:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Dialing and Sending, and then press
4 Press the arrow buttons to scroll to Scan, and then press

5 Press the arrow buttons to scroll to Before Dial, and then press

ENABLE ERROR CORRECTION
Errors and blurs may appear in the faxed document if there is too much noise on the line. This option enables the
printer to transmit the bad blocks of data again and correct the errors. When a fax has too many errors, the fax may
be rejected by the receiving fax machine.

Troubleshooting

113

To make sure that error correction is enabled:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Dialing and Sending, and then press
4 Press the arrow buttons to scroll to Error Correction, and then press

5 Check to see if error correction is set to On.
If it is not set to On, press the arrow buttons to select On, and then press

ENABLE AUTOMATIC FAX CONVERSION
If the receiving fax machine does not support color fax, then this option automatically converts the outgoing color
fax to black and white. It also automatically reduces the resolution of the fax to a resolution that the receiving
machine can support.
To make sure that automatic fax conversion is enabled:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Dialing and Sending, and then press
4 Press the arrow buttons to scroll to Auto Fax Convert, and then press

5 Check to see if automatic fax conversion is set to On.
If it is not set to On, press the arrow buttons to select On, and then press

MAKE SURE THAT THE DIAL PREFIX SETTING IS CORRECT
The dialing prefix is the number or series of numbers that you press before you can dial the actual fax number or
telephone number. If the printer is in an office setting or in a private branch exchange, this can be a specific number
that you need to press so you can make a call outside the office.
Make sure that the dial prefix entered in the printer is correct for your network.
To check the dial prefix setting:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Dialing and Sending, and then press
4 Press the arrow buttons to scroll to Dial Prefix, and then press

5 Press the arrow buttons to view the prefix.
6 If the prefix is not correct, enter the correct prefix, and then press

Troubleshooting

114

Cannot receive faxes
If the “Fax troubleshooting checklist” does not solve the problem, then try one or more of the following:

MAKE SURE THAT YOU HAVE CONFIGURED THE CORRECT SETTINGS FOR YOUR SETUP
The fax settings depend on whether the printer is connected to its own fax line or shares the line with other devices.
If the printer is sharing the telephone line with an answering machine, then make sure that the following are set:

• Auto Answer is On.
• The printer picks up on a greater number of rings than the answering machine.
• The printer picks up on the correct distinctive ring (if you subscribe to a distinctive ring service).
If the printer is sharing the telephone line with a telephone subscribed to voice mail, then make sure that the
following are set:
• Auto Answer is Off (if you have only one number on the telephone line).

• The printer picks up on the correct distinctive ring (if you subscribe to a distinctive ring service).

MAKE SURE THAT THE PRINTER IS CONNECTED TO AN ANALOG PORT
The printer is an analog device. If you are using a PBX system, then make sure that the printer is connected to an
analog port on the PBX. You may need a digital line converter that converts digital signals into analog signals.

MAKE SURE THAT THE PRINTER MEMORY IS NOT FULL
The printer saves an incoming fax to the printer memory before it prints the fax. If the printer runs out of ink or
runs out of paper while receiving the fax, then the printer saves the fax so you can print it later. However, if the
printer memory is full, then the printer may not be able to receive more incoming faxes. An error message appears
on the display when the printer memory is full. Resolve the error to free up space in the printer memory.

MAKE SURE THAT FAX FORWARDING IS DISABLED
You may have turned on Fax Forwarding. Disable this option so that the printer can receive the fax.

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Ringing and Answering, and then press
4 Press the arrow buttons to scroll to Fax Forward, and then press
5 Press the arrow buttons to scroll to Off, and then press

INCREASE THE RINGER VOLUME
If you set the printer to receive faxes manually (Auto Answer Off), then increase the ringer volume.

MAKE SURE THAT YOU HAVE THE CORRECT MANUAL ANSWER CODE
If you set the printer to receive faxes manually (Auto Answer Off), then you need to press the correct code when
a fax comes in so that the printer can receive it.

Troubleshooting

115

To retrieve the correct code:

1 From the printer control panel, press

2 Press the arrow buttons to scroll to Fax Setup, and then press

3 Press the arrow buttons to scroll to Ringing and Answering, and then press
4 Press the arrow buttons to scroll to Manual Pickup Code, and then press

5 Copy the manual answer code that appears on the display.

Cannot run the fax software
The printer must be connected to a telephone, DSL, VoIP, or cable service before you can configure the fax settings
in the fax software.

MAKE SURE THE PRINTER IS CONNECTED TO A TELEPHONE LINE
You need to connect the printer to your telephone line (through a standard wall jack, a DSL filter, a VoIP adapter,
or a cable modem) before you can open the fax software and configure the fax settings.

MAKE SURE THAT THE PRINTER IS CONNECTED TO THE COMPUTER
MAKE SURE THAT THE PRINTER IS NOT IN POWER SAVER MODE
Fax error messages on the printer control panel
Error Message:

What it indicates:

Remote Fax Error

The receiving fax machine cannot
receive the fax. The error on the
receiving end could be due to several
factors.

Possible solutions:

• Resend the fax. There may have
been a problem with the quality of
the connection.

• Decrease the transmission speed
of your fax modem.

• Register your user information. In
some countries, you cannot send a
fax without registering your fax
name and fax number. Some fax
machines also block faxes without
sender information.
Fax Mode Unsupported

The receiving fax machine does not
support color fax or the scan
resolution of the document that you
are sending.

• Enable Auto Fax Conversion. The
printer automatically converts
color faxes to black and lowers the
scan resolution of the document.

• Lower the fax quality.
• Reformat the document on
Letter-size paper.

Troubleshooting

116

Error Message:

What it indicates:

Possible solutions:

Unsupported Compression

The fax modem of the receiving fax
machine does not support data
compression. Fax modems compress
data to speed up transmission, but the
receiving fax modem needs to have
the same compression code.

• Lower the transmission speed of

Unsupported Resolution

The receiving fax machine does not
support the scan resolution of the
document that you are sending.

• Lower the fax quality.
• Enable Auto Fax Conversion.

Unrecoverable Fax Error

The fax modem encountered critical
errors.

Fax Modem Error

The fax modem of the printer may be Turn off the printer, turn it back on, and
busy, or the fax modem may have
then resend the fax.
encountered problems during
transmission.

Phone Line is connected to
the incorrect jack on the
back of the machine.

The telephone cable is connected to
the wrong port on the back of the
printer.

Connect the phone cable to the
on the back of the printer.

Digital line detected

The printer is connected to a digital
line.

The printer is an analog device and
must be connected to an analog line.
To connect the printer to a digital line,
you must use a digital line converter or
a filter.

the fax modem, and then resend
the fax.

• Enable Auto Fax Conversion.

Turn off the printer, turn it back on, and
then resend the fax.

port

For more information, see the ”Setting
up the printer to fax” section.
Failed to Connect
Phone Line Error

The printer cannot detect a dial tone. See the “Fax troubleshooting
checklist.”

Phone Line Not Connected
Phone Line Busy

Your telephone line or the telephone
line of the receiving fax machine is
busy. This happens especially if the
printer is sharing the line with other
devices (telephone, answering
machine).

• Set the printer to redial.
• Increase the time between the
redial attempts.

• Place a test call to the number to
which you want to send a fax to
make sure that it is working
correctly.

• If the telephone line is being used
by another device, then wait until
the other device is finished before
sending the fax.

• Schedule to resend the fax at a later
time.

• Set the printer to scan before
dialing. The scanned document is
saved in the printer memory. The
printer can then retrieve it and
automatically redial the number.

Troubleshooting

117

Error Message:

What it indicates:

No Answer

Auto Answer may have been turned
off on the receiving fax machine.

Possible solutions:

• Verify the number, and then resend
the fax.

• Set the printer to redial.
Note: Depending on your country
or region, there may be a limit on
the number of redial attempts,
regardless of the redial settings
that you set in your printer.

• Schedule to resend the fax at a later
time.
No Caller ID
Call Stopped

Your printer stopped the call because Disable Block No-ID.
the incoming fax has no sender
information. You may have chosen to
block faxes with no Caller ID or faxes
without Caller IDs are not allowed in
your country or region.

To troubleshoot error messages in the fax software, click Help to view the help information for the fax software.

Memory card troubleshooting
•
•
•
•

“Memory card troubleshooting checklist” on page 118
“Nothing happens when a memory card is inserted” on page 118
“Cannot print documents from a memory card or flash drive” on page 119
“Photos do not transfer from a memory card across a wireless network” on page 119

Memory card troubleshooting checklist
Before you troubleshoot, use the following checklist to solve most memory card problems:

•
•
•
•

Make sure that the memory card you are using can be used in the printer.
Make sure you insert the memory card into the correct slot.
Make sure the memory card is not damaged.
Make sure memory card contains supported file types.

Nothing happens when a memory card is inserted
If the "Memory card troubleshooting checklist" does not solve the problem, then try one or more of the following:

REINSERT THE MEMORY CARD
The memory card may have been inserted too slowly. Remove and then reinsert the memory card quickly.

118

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.
The USB port is marked with a

USB symbol.

CHECK THE NETWORK CONNECTION
If the printer and computer are connected over a network, then make sure that the correct host and device are
communicating. Select the printer from the computer or the computer from the printer.

Cannot print documents from a memory card or flash drive
If the "Memory card troubleshooting checklist" does not solve the problem, then try the following:

USB symbol.

Photos do not transfer from a memory card across a wireless
network
If the "Memory card troubleshooting checklist" does not solve the problem, then try one or more of the following:

MAKE SURE THAT BOTH THE PRINTER AND THE DESTINATION COMPUTER ARE TURNED ON AND
READY

SET YOUR PRINTER AS THE DEFAULT PRINTER FROM THE DESTINATION COMPUTER
SELECT THE CORRECT COMPUTER NAME FROM THE SCAN DESTINATION LIST ON THE PRINTER
MAKE SURE YOUR WIRELESS NETWORK IS CONNECTED AND ACTIVE
If your wireless connection is down, then use a USB cable to connect your printer to your computer.

Wireless troubleshooting
• “Wireless troubleshooting checklist” on page 120
• “Resetting the wireless settings to factory defaults” on page 120
• “Cannot print over wireless network” on page 121
Troubleshooting

119

•
•
•
•
•
•
•
•
•
•

“The Continue button is unavailable” on page 123
“Cannot print and there is a firewall on the computer” on page 124
“Wi-Fi indicator light is not lit” on page 124
“Wi-Fi indicator light is green but the printer does not print (Windows only)” on page 125
“Wi-Fi indicator light is still orange” on page 126
“Wi-Fi indicator light is blinking orange during installation” on page 127
“Wireless print server not installed” on page 130
““Communication not available” message displays when printing wirelessly” on page 130
“Communication with printer lost when connected to Virtual Private Network (VPN)” on page 132
“Resolving intermittent wireless communications issues” on page 132

Wireless troubleshooting checklist
Before beginning to troubleshoot the wireless printer, verify the following:

• The printer, the computer, and the wireless access point are all plugged in and turned on.
• The wireless network is working properly.
Try accessing other computers on your wireless network.
If your network has Internet access, try connecting to the Internet over a wireless connection.

• Your SSID is correct.
Print a network setup page to verify the SSID the printer is using.
If you are not sure if your SSID is correct, then run the wireless setup again.
• Your WEP key or WPA passphrase is correct (if your network is secure).
Log into the wireless access point (wireless router) and check the security settings.
A security key is like a password. All devices on the same wireless network using WEP, WPA, or WPA2 share the
same security key.
If you are not sure if your security information is correct, run the wireless setup again.

• The printer and the computer are within the range of the wireless network.
For most networks, the printer and the computer should be within 100 feet (30 meters) of the wireless access
point (wireless router).

•
•
•
•
•

The Wi-Fi indicator light is lit and is solid green.
The printer driver is installed on the computer from which you are performing a task.
The correct printer port is selected.
The computer and printer are both connected to the same wireless network.
The printer is located away from obstacles or electronic devices that could interfere with the wireless signal.
Make sure the printer and wireless access point are not separated by poles, walls, or support columns containing
metal or concrete.
Many devices can interfere with the wireless signal, including baby monitors, motors, cordless phones, security
system cameras, other wireless networks, and some Bluetooth devices.

Resetting the wireless settings to factory defaults
1 From the printer control panel, press

2 Press the arrow buttons to scroll to Network Setup, and then press
Troubleshooting

120

3 Press the arrow buttons to scroll to Reset Network Adapter Defaults, and then press
4 Press the arrow buttons to scroll to Yes, and then press

The printer wireless settings are reset to factory default settings. To verify, print a network setup page.

Cannot print over wireless network
If you encountered problems while installing, or if your printer does not appear in the printers folder or as a printer
option when sending a print job, then you can try uninstalling and reinstalling the software.
Before you reinstall the software, check the troubleshooting checklist, and then do the following:

MAKE SURE YOUR COMPUTER IS CONNECTED TO YOUR WIRELESS ACCESS POINT (WIRELESS
ROUTER)
• See if you have access to the Internet by opening your Web browser and accessing any site.
• If there are other computers or resources on your wireless network, then check to see if you can access them
from your computer.

MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE WIRELESS ROUTER
Although the possible distance between devices in 802.11b or 802.11g networks is 300 feet, the maximum range
for optimal performance is generally 100-150 feet.

MOVE YOUR ACCESS POINT AWAY FROM OTHER ELECTRONIC DEVICES
There may be temporary interference from electronic devices such as microwave ovens or other appliances,
cordless phones, baby monitors, and security system cameras. Make sure your access point is not positioned too
closely to these devices.

MAKE SURE THAT YOUR COMPUTER AND PRINTER ARE CONNECTED TO THE SAME WIRELESS
NETWORK

If the printer is not on the same wireless network as the computer, you will not be able to print wirelessly. The SSID
of the printer must match the SSID of the computer, if the computer is already connected to the wireless network.

1 Obtain the SSID of the network that the computer is connected to.
a Type the IP address of your wireless access point (wireless router) into the address field of your Web browser.
If you do not know the IP address of the wireless access point:
1 Click , or click Start and then click Run.
2 In the Start Search or Run box, type cmd.
3 Press Enter or click OK.
The Command Prompt window opens.
4 Type ipconfig, and then press Enter. Check the Wireless Network Connection section:

• The “Default Gateway” entry is typically the wireless access point .
• The IP address appears as four sets of numbers separated by periods, such as 192.168.2.134.
b Type the user name and password of the router when prompted.
c Click OK.
Troubleshooting

121

d On the main page, click Wireless or any other selection where settings are stored. The SSID will be displayed.
e Write down the SSID.
Note: Make sure you copy it exactly, including any capital letters.

2 Print the printer network setup page.
In the Wireless section, look for SSID.

CHECK YOUR WEP KEY OR WPA PASSPHRASE
If your wireless access point is using Wireless Equivalent Privacy (WEP) security, then the WEP key should be:

• Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.
or
• Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard. ASCII
characters in a WEP key are case-sensitive.
If your wireless access point is using Wi-Fi Protected Access (WPA) security, then the WPA passphrase should be:

• From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.
or

• Exactly 64 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.
Note: If you do not know this information, then see the documentation that came with the wireless network, or
contact the person who set up your wireless network.

DISCONNECT FROM VPN SESSION
When you are connected to another network through a VPN connection, you will not be able to access the printer
over your wireless network. End your VPN session and try printing again.

CHECK YOUR ADVANCED SECURITY SETTINGS
• If you are using MAC address filtering to limit access to your wireless network, then you must add the printer
MAC address to the list of addresses allowed to connect to the wireless access point.

• If you set the wireless access point to issue a limited number of IP addresses, then you must change this so that
the printer can be added.
Note: If you do not know how to make these changes, then see the documentation that came with the wireless
network, or contact the person who set up your wireless network.

Troubleshooting

122

The Continue button is unavailable
Try the following solutions in the order they appear until the Continue button becomes active and can be clicked:

CHECK IF THE USB CABLE IS SECURELY PLUGGED INTO THE USB PORTS ON BOTH THE
COMPUTER AND THE PRINTER

USB ports are marked with the

symbol.

MAKE SURE THAT THE PRINTER IS PLUGGED IN AND TURNED ON
Check to see if the button is lit. If you have just turned on the printer, then you might need to disconnect the
USB cable and reconnect it.

MAKE SURE THAT THE USB PORT ON THE COMPUTER IS WORKING
Test the USB port by connecting other devices to it. If you can successfully use other devices from the port, then
the port is working.
If the USB port on the computer is not working, then try using the other USB ports on the computer.

MAKE SURE THAT THE USB CABLE IS WORKING
Try using a different USB cable. If you are using a cable longer than 10 feet, then try using a shorter cable.

MAKE SURE THAT YOU ARE USING THE CORRECT CD FOR YOUR PRINTER MODEL
Compare the printer model on the CD to the printer model on the printer. The numbers should either match exactly
or be within the same series.
If you have any doubts, look for an updated version of the printer software on our Web site. For more information,
see “Installing the printer software” in the User's Guide. You can access the User's Guide from the link at the bottom
of the installation screen.

RECONNECT THE POWER SUPPLY
1 Turn off the printer.
2 Unplug the power cord from the power outlet.
3 Remove the power supply from the back of the printer and then plug it back in.
4 Plug the power cord back into the power outlet.
5 Turn on the printer, and then resume the installation on your computer.

TRY RUNNING THE INSTALLER AGAIN
1 Close the installer.
2 Remove the CD, and then restart the computer.
3 Insert the CD and then run the installer again.

Troubleshooting

123

Notes:

• When you get to the Software Already Installed screen, make sure you select Install a printer.
• If you have already set up your printer, select Additional Computer when you get to the Setting up a
new printer? screen to skip the hardware setup wizard.

CHECK THAT YOUR COMPUTER IS ABLE TO ACKNOWLEDGE USB ACTIVITY ON THE USB PORT
Open the Device Manager to check if it has activity whenever a USB device is connected to a USB port:

1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type devmgmt.msc.
3 Press Enter, or click OK.
The Device Manager opens.

4 Watch the Device Manager window while connecting a USB cable or another device to the USB port. The
window refreshes when Device Manager recognizes the USB connection.

• If there is activity on Device Manager but none of the previous solutions worked, call Customer Support.
• If there is no activity on Device Manager, there may be a problem with your computer and its USB support.
The computer must recognize the USB connection in order for installation to work.

Cannot print and there is a firewall on the computer
Third-party (non-Microsoft) firewalls can interfere with wireless printing. If the printer and computer are configured
correctly, and the wireless network is working, but the printer will not print wirelessly, then a firewall could be the
problem. If there is a firewall (other than the Windows firewall) on the computer, try one or more of the following:

• Update the firewall using the most recent update available from the manufacturer. Refer to the documentation
that came with your firewall for instructions on how to do this.

• If programs request firewall access when you install the printer or try to print, make sure you allow those programs
to run.

• Temporarily disable the firewall and install the wireless printer on the computer. Re-enable the firewall when you
have completed the wireless installation.

Wi-Fi indicator light is not lit
CHECK POWER
If the Wi-Fi indictor light is off, make sure the light is on. If the
• Make sure the printer is plugged in and turned on.

light is not on, check the following:

• Make sure the printer is plugged into a working outlet.
• If the printer is plugged into a power strip, make sure it is turned on and working.

Troubleshooting

124

Wi-Fi indicator light is green but the printer does not print
(Windows only)
If you have completed the configuration for wireless printing and all of the settings appear to be correct, but the
printer does not print, then try one or more of the following:

ALLOW THE WIRELESS INSTALLATION TO COMPLETE
Do not attempt to print, remove the installation CD, or detach the installation cable until you see the Wireless
Setup Successful screen.

ENABLE THE PRINTER
Confirm that the printer is enabled:

1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the new printer; from the menu, select Use Printer Online.
5 Close the Printers or Printers and Faxes window and try printing again.

SELECT THE WIRELESS PRINTER
You may need to select the wireless printer from your computer to use the printer wirelessly.

1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer in the folder with the matching name and model number followed by ”(Network).”
5 Select Use Printer Online from the menu.
6 Close the Printers or Printers and Faxes window and try printing again.

SELECT THE WIRELESS PORT
If you have previously set up your printer as a locally attached printer, then you may need to select the wireless
printer to use the printer wirelessly.

1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Properties from the menu.
Troubleshooting

125

5 Click the Ports tab.
6 Locate the selected port. The selected port has a check beside it in the Port column.
7 If the Description column of the selected port indicates that it is a USB port, scroll through the list and select
the port with Printer Port in the Description column. Check the printer model in the Printer column to make
sure you select the right printer port.

8 Click OK, and then try to print again.

Wi-Fi indicator light is still orange
When the Wi-Fi indicator light is orange, it may indicate that the printer is:

• Not configured in infrastructure mode
• Waiting to make an ad hoc connection to another wireless device
The printer may be unable to join the network because of interference, its distance from the wireless access point
(wireless router), or until its settings are changed.
These are possible solutions. Try one or more of the following:

CHECK NETWORK NAME
Make sure your network does not have the same name as another network near you. For example, if you and your
neighbor both use a manufacturer's default network name, your printer could be connecting to your neighbor's
network.
If you are not using a unique network name, consult the documentation for your wireless access point (wireless
router) to learn how to set a network name.
If you set a new network name, you must reset the printer and computer SSID to the same network name.

CHECK SECURITY KEYS
If you are using WEP security
A valid WEP key is:
• Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.
or

• Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.
If you are using WPA security
A valid WPA passphrase is:
• From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.
or

• Exactly 64 hexadecimal characters. Hexadecimal characters are A-F, a-f, and 0-9.
If your wireless network is not using security, then you will not have a security key. Using a wireless network with
no security is not recommended because it can allow intruders to use your network resources without your consent.

Troubleshooting

126

MOVE YOUR PRINTER
Move the printer closer to the wireless access point (wireless router). Although the possible distance between
devices in 802.11b or 802.11g networks is 300 feet, the maximum range for optimal performance is generally
100-150 feet.
You can find the strength of the network signal on the printer network setup page.

CHECK MAC ADDRESS
If your network uses MAC address filtering, make sure that you include the MAC address of the printer in the MAC
address filter list. This will allow the printer to operate on the network.

Wi-Fi indicator light is blinking orange during installation
When the Wi-Fi indicator light is blinking orange, it indicates that the printer has been set up for wireless networking
but cannot connect to the network for which it has been configured. The printer may be unable to join the network
because of interference, its distance from the wireless access point (wireless router), or until its settings are changed.
These are possible solutions. Try one or more of the following:

MAKE SURE THE ACCESS POINT IS ON
Check the access point and, if necessary, turn it on.

MOVE YOUR ACCESS POINT TO MINIMIZE INTERFERENCE
There may be temporary interference from other devices such as microwave ovens or other appliances, cordless
phones, baby monitors, and security system cameras. Make sure your access point is not positioned too closely to
these devices.

MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE WIRELESS ACCESS POINT (WIRELESS
ROUTER)
Move the computer and/or printer closer to the access point. Although the possible distance between devices in
802.11b or 802.11g networks is 300 feet, the maximum range for optimal performance is generally 100–150 feet.
You can find the signal strength of the network on the network setup page.

CHECK YOUR WEP KEY OR WPA PASSPHRASE
A WEP key or WPA passphrase is like a password. All devices on a WEP-secured wireless network must share the
same WEP key, and all devices on a WPA-secured wireless network must share the same WPA passphrase.
Note: Make sure you copy it exactly, including any capital letters, and store it in a safe place for future reference.

If you are using WEP security
A valid WEP key is:

• Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.
or

• Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard.
Troubleshooting

127

If you are using WPA security
A valid WPA passphrase is:

• From 8 to 63 ASCII characters. ASCII characters in a WPA passphrase are case-sensitive.
or

• Exactly 64 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.
If your wireless network is not using security, then you will not have a security key. Using a wireless network with
no security is not recommended because it can allow intruders to use your network resources without your consent.

PING THE ACCESS POINT TO MAKE SURE THE NETWORK IS WORKING
1 If you do not already know it, find the IP address of the access point:
a Click , or click Start and then click Run.
b In the Start Search or Run box, type cmd.
c Press Enter, or click OK.
The Command Prompt window opens.

d Type ipconfig, and then press Enter.
• The “Default Gateway” entry is typically the wireless access point.
• The IP address appears as four sets of numbers separated by periods, such as 192.168.2.134.
2 Ping the access point:
a Click , or click Start and then click Run.
b In the Start Search or Run box, type cmd.
c Press Enter, or click OK.
The Command Prompt window opens.

d Type ping followed by a space and the IP address of the wireless access point. For example:
ping 192.168.1.100

e Press Enter.
3 Check to see whether the access point responds:
• If the access point responds, you will see several lines appear that start with “Reply from.”
It is possible that the printer did not connect to the wireless network. Turn off and then restart the printer
to try to connect again.
• If the access point does not respond, it will take several seconds and then you will see “Request timed out.”
Try the following:
a Click , or click Start and then click Run.
b In the Start Search or Run box, type ncpa.cpl, and then press Enter.
c Press Enter or click OK.

Troubleshooting

128

d Select the appropriate connection from the ones shown.
e Right-click the connection, and then click Repair.

MAKE SURE YOUR COMPUTER CAN COMMUNICATE WITH THE PRINTER
1 Obtain the printer IP address by printing a network setup page.
2 Click

, or click Start and then click Run.

3 In the Start Search or Run box, type cmd.
4 Press Enter, or click OK.
The Command Prompt window opens.

5 Type ping followed by a space and the IP address of the printer. For example:
ping 192.168.1.100

6 Press Enter.
7 If the printer responds, you will see several lines that display the number of bytes received from the printer.
This ensures that your computer is communicating with your printer.
If the printer does not respond, then “Request timed out” displays.

• Your computer might not be connected to the network.
• You may need to change the settings of your printer. Run the Wireless Setup Utility again.

CONFIGURE THE PRINTER FOR WIRELESS ACCESS AGAIN
If your wireless settings have changed, you must run the printer wireless setup again. Some reasons your settings
may have changed include your having manually changed your WEP or WPA keys, channel, or other network
settings; or the access point having been reset to factory defaults.
Running the wireless setup again can also resolve issues due to misconfigurations that occurred when configuring
the printer for wireless access.
Notes:

• If you change network settings, change them on all the network devices before changing them for the access
point.

• If you have already changed the wireless network settings on your access point, then you must change the
settings on all the other network devices before you can see them on the network.

1 Click

or Start.

2 Click All Programs or Programs, and then select the printer program folder from the list.
3 Select Printer Home.
4 Click the Settings tab.
5 Click the Wireless setup utility link.
Note: You may be prompted to connect the printer to the computer again using the installation cable as part
of the setup process.

6 Follow the instructions on the computer screen.

Troubleshooting

129

Wireless print server not installed
You may see a message during installation indicating that the printer does not have a wireless print server installed.
If you are sure the printer is capable of wireless printing, try the following:

CHECK POWER
Make sure the

light is on.

“Communication not available” message displays when printing
wirelessly
These are possible solutions. Try one or more of the following:

MAKE SURE YOUR COMPUTER AND PRINTER HAVE VALID IP ADDRESSES FOR THE NETWORK
If you are using a laptop and have power saving settings enabled, you may see the Communication not
available message on your computer screen when you attempt to print wirelessly. This can occur if the laptop
hard drive has powered down.
If you see this message, wait a few seconds and then try to print again. The laptop and printer require a few seconds
to power up again and reattach to the wireless network.
If you see this message again after you have waited long enough for the printer and the laptop to attach to the
network, there may be a problem with your wireless network.
Make sure that the laptop and printer have both received IP addresses:

1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type cmd.
3 Press Enter, or click OK.
The Command Prompt window opens.

4 Type ipconfig, and then press Enter.
The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.

How to locate a printer IP address
• You can locate the printer IP address by viewing the printer network setup page.
If the printer and/or the laptop does not have an IP address, or if either has an address of 169.254.x.y (where x and
y are any two numbers between 0 and 255):

1 Turn off the device that does not have a valid IP address (the laptop, the printer, or both).
2 Turn on the device(s).
3 Check the IP addresses again.
If the laptop and/or printer still does not receive a valid IP address, there is a problem with your wireless network.
Try the following:

• Make sure you wireless access point (wireless router) is turned on and is working.
• Remove any objects that could be blocking the signal.

Troubleshooting

130

• Temporarily turn off any unnecessary wireless devices on your network and pause any network-intensive
activities, like large file transfers or network games. If the network is too busy, it is possible that the printer is
not receiving the IP address within the allowed time.

• Make sure your DHCP server, which may also be your wireless router, is working and is configured to assign IP
addresses. If you are not sure how to do this, refer to the manual that came with your wireless router for more
information.
If the printer and computer have valid IP addresses and the network is operation correctly, continue
troubleshooting.

MAKE SURE THE WIRELESS PORT IS SELECTED
1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Properties from the menu.
5 Click the Ports tab.
6 Locate the selected port. The selected port has a check beside it in the Port column.
7 If the Description column of the selected port indicates that it is a USB port, scroll through the list and select
the port with Printer Port in the Description column. Check the printer model in the Printer column to make
sure you select the right printer port.

8 Click OK, and then try to print again.

MAKE SURE BIDIRECTIONAL COMMUNICATION IS ENABLED
1 Click

, or click Start and then click Run.

2 In the Start Search or Run box, type control printers.
3 Press Enter, or click OK.
The printer folder opens.

4 Right-click the printer, and then select Properties from the menu.
5 Click the Ports tab.
6 Click the box next to Enable bidirectional support if it is not already checked.
7 Click Apply.
8 Click OK, and then try to print again.

Troubleshooting

131

Communication with printer lost when connected to Virtual Private
Network (VPN)
You will lose your connection to a wireless printer on your local network when connected to most Virtual Private
Networks (VPNs). Most VPNs allow users to communicate with only the VPN and no other network at the same time.
If you would like to have the ability to connect to your local network and to a VPN at the same time, the system
support person for the VPN must enable split tunneling. Be aware that some organizations will not allow split
tunneling due to security or technical concerns.

Resolving intermittent wireless communications issues
You may notice that your printer works for a short time and then stops working, although apparently nothing has
changed on your wireless network.
Many different issues can interrupt network communications, and sometimes more than one problem exists at the
same time. These are possible solutions. Try one or more of the following:

DISCONNECT FROM ALL VPNS WHEN ATTEMPTING TO USE THE WIRELESS NETWORK
Most Virtual Private Networks (VPNs) allow computers to communicate with only the VPN and no other network
at the same time. Disconnect from the VPN before installing the driver on the computer or before running the
wireless setup on the computer.
To check if the computer is currently connected to a VPN, open your VPN Client software and check your VPN
connections. If you do not have a VPN Client software installed, check the connections manually using the Windows
VPN Client.
If you would like to have the ability to connect to your local network and to a VPN at the same time, the system
support person for the VPN must enable split tunneling. Be aware that some organizations will not allow split
tunneling due to security or technical concerns.

TURN OFF THE WIRELESS ACCESS POINT (WIRELESS ROUTER) AND TURN IT BACK ON AGAIN
ELIMINATE NETWORK CONGESTION
If a wireless network is too busy, the computer and printer may have difficulty communicating with each other.
Some causes of wireless network congestion can include:

•
•
•
•
•

Transferring large files across the network
Networked games
Peer-to-peer file swapping applications
Streaming video
Too many computers on the wireless network at once

ELIMINATE SOURCES OF INTERFERENCE
Common household items can potentially disrupt wireless network communications. Cordless phones (but not
cellular phones), microwave ovens, baby monitors, almost any kitchen appliance, wireless surveillance equipment,
nearby wireless networks, and any appliance containing a motor can disrupt wireless network communications.
Try turning on any potential sources of interference and see if it causes the problem. If it does, separate your wireless
network from the device.
Troubleshooting

132

CHANGE THE CHANNEL THE WIRELESS ROUTER USES
You can sometimes eliminate interference from unknown sources by changing the channel your wireless router
uses to broadcast. There are three distinct channels on a router. Check the documentation that came with your
router to determine which three apply. Other channels are offered as options, but these overlap. If the router is
configured to use the default settings, change the channel setting to use a different distinct channel. Refer to the
manual that came with your wireless router if you are not sure how to change the channel.

CONFIGURE THE WIRELESS ROUTER WITH A UNIQUE SSID
Many wireless networks use the SSID that the router was originally configured by the manufacturer to use. Using
the default SSID can cause problems when more than one network is operating in the same area with the same
SSID. The printer or computer may attempt to attach to the wrong network, although it will appear to be trying to
connect to the correct network.
To avoid this type of interference, change the SSID on your wireless router from the default. Refer to the manual
that came with your router if you are not sure how to change the SSID.
Note: You must change the SSID on all of the other devices that access your wireless network if you change the
SSID on the router.

ASSIGN STATIC IP ADDRESSES TO ALL DEVICES IN THE NETWORK
Most wireless networks use a DHCP server (dynamic host configuration protocol) built in to the wireless router to
assign IP addresses to clients on the wireless network. DHCP addresses are assigned when they are needed, as
when a new device is added to the wireless network or when it is powered on. Wireless devices must send a request
to the router, and receive an IP address in response so they can function on the network. Because the router
performs many other tasks besides assigning addresses, it sometimes does not respond quickly enough with an
address. The requesting device sometimes gives up before it receives an address.
Try assigning static IP addresses to the devices in your network to resolve this issue. Static IP addresses cut down
on the work your wireless router has to do. Refer to the manual that came with your router and your operating
system documentation if you are not sure how to assign static IP addresses.
To assign a static IP address to the printer, do the following:

4 Click the Configuration link.
5 Click the TCP/IP link.
6 Click the Set Static IP Address link.
7 Type the IP address you want to assign to the printer in the IP Address field.
8 Click the Submit button.
The Submitting Selection message appears.
Confirm that the IP address is updated by typing the static IP address in the browser address field and checking to
see if the printer Web page reloads.

Troubleshooting

133

CHECK FOR KNOWN ISSUES WITH THE WIRELESS ROUTER
Some wireless routers have documented defects that were identified and resolved by the manufacturers. Visit the
company Web site of the router manufacturer. Check for firmware updates and other advice from the manufacturer.
Check the manual that came with your wireless router if you are not sure how to reach the manufacturer Web site.

CHECK FOR WIRELESS ADAPTER UPDATES
If you are having trouble printing from one particular computer, check the Web site of the manufacturer of the
network adapter card in that computer. It is possible that there is an updated driver available that could resolve
the issue.

CHANGE ALL NETWORK DEVICES TO THE SAME TYPE
While it is possible to successfully mix 802.11b, 802.11g, and 802.11n devices on the same wireless network, the
faster devices will sometimes prevent the slower devices from communicating. Wireless devices are designed to
wait for a gap in wireless network communications before attempting to send information. If newer, faster devices
are constantly using the wireless network, then older, slower devices will not have a chance to send data.
Try only turning on the network devices of the same type and see if network communications improve. If this solves
the problem, you may want to upgrade your older devices with newer network adapters.

PURCHASE A NEW ROUTER
If your router is several years old, it may not be fully compatible with the newer wireless devices on your network.
Consider purchasing a newer router that is fully compliant with the 802.11 IEEE specifications.

Troubleshooting

134

Index
A
ad hoc
SSID 84
WEP 84
ad hoc network 92
ad hoc wireless network
adding a printer 86
creating using Windows 84
additional computers
installing wireless printer 82
Address Book
setting up 70
Address Book, fax
setting 68
adjusting dialing and ringer
volume 76
adjusting speaker volume 76
AliceBox 83
aligning the printhead 98
answering machine
best settings for fax 76
setting up 57
appliances
wireless network 94
application list
downloading 56
updating 56
assigning IP address 97
Auto Answer
when to turn on 74
Automatic Document Feeder
(ADF) 11
clearing a paper jam in 107
loading documents 29
output tray 11
paper capacity 29
paper guide 11
tray 11
automatic fax conversion
setting 68

B
banner paper 27
bidirectional communication
enabling 130
black and white scanning 55
blocking faxes 79

Bluetooth
printing 43
setting the security level 43
setting up a connection 41
broadcast fax, sending
immediately 71
buttons, printer control panel
Address Book 17
Back 17
Cancel 18
Color/Black 18
Copy 16
Dialtone 18
Display 17
Fax 16
Keypad 18
Photo 16
Power 16
Scan 16
Select 17
Settings 17
Start 18

C
cable
installation 91, 92
USB 92
Caller ID 67
Caller ID pattern, fax
setting 68
camera
connecting 39
canceling
copy job 51
print job 46
scan job 56
cannot delete documents from
print queue 106
cannot print from a flash drive 119
cannot print over wireless
network 121
cannot print through USB 106
cannot receive faxes 115
cannot run fax software 116
cannot scan to computer over a
network 111
cannot send faxes 113
changing Power Saver timeout 21
Index

135

changing printing mode 45
changing temporary settings into
default 20
changing wireless settings after
installation (Windows) 84
checking an unresponsive
printer 101
checking ink levels 98
checking the dial tone 75
checklist
before you troubleshoot 101
fax troubleshooting 112
memory card
troubleshooting 118
choosing a splitter, faxing 74
cleaning exterior of the printer 99
cleaning printhead nozzles 99
Club Internet 83
collating copies 49
Communication not available
message 130
computer slows down when
printing 110
configuring
fax settings 68
IP address 83
confirmation page, fax 78
connection
configurations 95
conserving energy, ink, and
paper 8
conserving paper
using Eco-Mode 22
contact list
setting up 70
continue button greyed out 123
continue button not working 123
continue button unavailable 123
copier or scanner does not
respond 110
copies
making 47
copy and scan troubleshooting
cannot scan to computer over a
network 111
copier or scanner does not
respond 110

partial document or photo
scans 111
poor scanned image quality 110
scan not successful 111
scanning takes too long or freezes
the computer 111
copy job
canceling 51
copy quality, adjusting 48
copy troubleshooting
scanner unit does not close 110
copying 47
adjusting quality 48
collating copies 49
enlarging an image 48
making a copy lighter or
darker 49
multiple page images on one
sheet 50
on both sides of the paper 50
Pages per Sheet 50
photos 47
reducing an image 48
repeating an image 50
tips 47
custom-size paper
printing on 34

D
default printer, setting 44
defaults
resetting factory defaults 21
dial method, fax
setting 68
dial tone
checking 75
dial tone volume
adjusting 76
dialing prefix 74
Digital Subscriber Line (DSL)
fax setup 60
digital telephone service
fax setup 62
disabling settings timeout 20
distinctive ring 75
documents
faxing using the computer 72
faxing using the control panel 71
loading into the Automatic
Document Feeder (ADF) 29
loading on scanner glass 29
printing 31

scanning for editing 54
scanning using the printer control
panel 52
DSL filter 60
duplex
copying, manual 50
printing, manual 34
duplex cover 11

E
Eco-Mode
using 22
energy
conserving 8
enlarging an image 48
entering
fax user information 67
envelopes 27
loading 33
printing 33
error correction, fax
setting 68
error using memory card 118
Ethernet 95
exterior of the printer
cleaning 99
e-mailing
scanned documents 54

F
factory default settings
resetting internal wireless print
server 120
resetting to 21
failed faxes
retrieving 79
fax
confirmation page 78
printer memory 79
transmission report 78
fax activity report 78
fax blocking
setting 68
fax error messages
Digital Line Detected 117
Failed To Connect 117
Fax Mode Unsupported 116
Fax Modem Error 117
No Answer 118
No Caller ID 118
Phone Line Busy 117
Index

136

Phone Line Error 117
Phone Line is connected to the
incorrect jack on the back of the
machine 117
Phone Line Not Connected 117
Remote Fax Error 116
Unrecoverable Fax Error 117
Unsupported Compression 117
Unsupported Resolution 117
fax footer
setting 68
fax forwarding 78
fax header
setting 68
fax header and footer
setting 67
fax number 74
fax printing
setting 68
fax quality
setting 77
fax resolution
setting 77
fax sending speed
setting 68
fax settings
configuring 68
for answering machine 76
for voice mail 76
fax setup
country-specific 63
digital telephone service 62
DSL connection 60
standard telephone line
connection 57
VoIP 61
Fax Setup Utility 68
Fax Setup Wizard 68
fax troubleshooting
cannot receive faxes 115
cannot run fax software 116
cannot send faxes 113
error messages, printer control
panel 116
fax troubleshooting checklist 112
faxing
Address Book 70
blocking 79
calling card, using 77
dial prefix 74
distinctive ring 75
pick up on 75

receiving automatically 72
receiving manually 73
rings 75
scheduling 77
sending a broadcast fax
immediately 71
sending using the control
panel 71
setup 73
tips, receiving 72
tips, sending 71
using the computer 72
using the control panel 71
faxing tips
receiving faxes automatically 72
receiving faxes manually 73
file types
supported 37
finding
information 9
MAC address 96
publications 9
Web site 9
firewall on computer 124
flash drive
inserting 36
printing documents from 32
printing photos using the proof
sheet 40
scanning to 53
forwarding faxes 78
France
special wireless setup
instructions 83
FreeBox 83

G
greeting cards 28
Group Dial
setting up 70

H
heavyweight matte paper 27

I
improving scan quality 55
incorrect language appears on
display 102
index cards 28
information
finding 9

information needed for setting up
printer on wireless network 81
infrastructure network 92
ink
conserving 8
ink cartridges
ordering 14
replacing 13
ink levels
checking 98
inserting a memory card or flash
drive 36
installation
cable 91, 92
installing
network printer 97
installing printer
on wireless network
(Windows) 82
installing printer software 25
installing wireless printer
additional computers 82
interference
wireless network 94
internal wireless print server
resetting to factory default
settings 120
IP address 96, 97
configuring 83
IP address, assigning 97
iron-on transfers 28

J
jams and misfeeds troubleshooting
paper jam in the ADF 107
paper jam in the paper
support 107
paper jam in the printer 106
paper or specialty media 108
junk faxes
blocking 79

K
key index 97

L
labels 27
printing 34
language
changing 102
line filter 60
Index

137

LiveBox 83
loading
documents into the Automatic
Document Feeder (ADF) 29
documents on scanner glass 29
envelopes 33
loading paper 26
locating
SSID 89
WEP key 89
WPA passphrase 89

M
MAC address 95
finding 96
MAC address filtering 95
memory card
inserting 36
printing documents from 32
printing photos using the proof
sheet 40
scanning to 53
supported types 37
memory card cannot be
inserted 118
memory card slots 11
memory card troubleshooting
cannot print from a flash
drive 119
checklist 118
nothing happens when memory
card is inserted 118
menus
diagram of 18
menus list 18
minimum system requirements 23
multiple WEP keys 97

N
N9UF Box 83
network connection
with USB 95
network overview 89
network printer
installing 97
network security 90
network setup page
printing 81
networking
finding IP address of
computer 97

finding IP address of printer 97
IP addresses 97
no wireless network 84
nothing happens when memory
card is inserted 118

O
on-hook faxing 77

P
page does not print 104
Pages per Sheet copies 50
paper
conserving 8
paper and media
banner paper 27
envelopes 27
heavyweight matte paper 27
index cards 28
iron-on transfers 28
photo cards 28
photo/glossy paper 28
plain paper 26
postcards 28
transparencies 28
paper default settings
saving 28
paper exit tray 11
paper feed guard 11
paper guides 11
paper jam in the ADF 107
paper jam in the paper
support 107
paper jam in the printer 106
paper or specialty media
misfeeds 108
paper support 11
partial document or photo
scans 111
parts
Automatic Document Feeder
(ADF) 11
Automatic Document Feeder
(ADF) output tray 11
Automatic Document Feeder
(ADF) paper guide 11
Automatic Document Feeder
(ADF) tray 11
duplex cover 11
memory card slots 11
paper exit tray 11

paper feed guard 11
paper guides 11
paper support 11
PictBridge port 11
power supply port 12
printer control panel 11
printhead 12
scanner glass 12
scanner unit 12
security slot 12
top cover 12
USB port 12
Wi-Fi indicator 11
password 90
pausing
print job 45
PDF
creating from scan 55
phone book
setting up 70
phone plug 63
phone splitter 61
photo cards 28
photo/glossy paper 28
photos
copying photos 47
making borderless copies 48
printing from digital camera using
DPOF 41
printing using printer control
panel 37
printing using the proof sheet 40
scanning for editing 53
photos do not print from memory
card across wireless network 119
photos from memory device
printing using printer
software 38
PictBridge port 11
PictBridge-enabled camera
connecting 39
plain paper 26
poor quality at the edges of
page 108
poor scanned image quality 110
postcards 28
Power Saver timeout
changing 21
power supply port 12
print job
canceling 46
pausing 45
Index

138

resuming 45
print media
greeting cards 28
labels 27
print speed is slow 109
print troubleshooting
cannot delete documents from
print queue 106
computer slows down when
printing 110
poor quality at the edges of
page 108
slow print speed 109
streaks or lines on printed
image 109
printer
sharing 87
sharing in Windows 87
printer control panel 11
using 16
printer does not print
wireless 124
printer does not print
wirelessly 125
printer does not respond 105
printer memory
fax 79
printer menus 18
printer printing blank pages 105
printer problems, basic
solutions 101
printer software
installing 25
uninstalling 25
printer, setting as default 44
printhead 12
aligning 98
printhead error 102
printhead nozzles
cleaning 99
printing
collate 31
custom-size paper 34
documents 31
documents from memory card or
flash drive 32
envelopes 33
from a Bluetooth-enabled
device 43
from a PictBridge-enabled
camera 39
labels 34

last page first 32
multiple pages on one sheet 32
network setup page 81
on both sides of the paper 34
photos from digital camera using
DPOF 41
photos from memory device using
printer software 38
photos using printer control
panel 37
photos using the proof sheet 40
reverse page order 32
tips 31
two-sided 34
printing a confirmation page 78
printing a transmission report 78
printing in draft mode 45
printing mode
changing 45
proof sheet
using 40
protocol 97
publications
finding 9

R
received history report 78
receiving faxes
Auto Answer setting 72, 73
automatically 72
manually 73
tips 72, 73
recycling 8
Dell products 15
redial attempts, fax
setting 68
redial time, fax
setting 68
reducing an image 48
registering
fax user information 67
Transmit Terminal Identification
(TTI) 67
repeating an image 50
replacing ink cartridges 13
reports
fax history 78
reports, fax
setting 68
resetting
internal wireless print server to
factory default settings 120

resetting to factory defaults 21
resuming
print job 45
reverse page order 32
ringer volume
adjusting 76
RJ-11 adapter 63

S
safety information 7
saving paper default settings 28
scan
black and white 55
improving quality 55
PIN 55
scan job
canceling 56
scan was not successful 111
scanner glass 12
cleaning 100
scanner unit 12
scanner unit does not close 110
scanning
creating a PDF from scan 55
documents for editing 54
documents for e-mailing 54
photos for editing 53
tips 52
to a computer 52
to a flash drive 53
to a memory card 53
to a network 52
using the printer control
panel 52
scanning takes too long or freezes
the computer 111
scheduled fax
sending 77
security
wireless network 80
security information
wireless network 90
security key 90
selecting the wireless port 130
sender information
registering 67
sending a scheduled fax 77
sending faxes, tips 71
sent history report 78
Service Center 101
setting
Auto Answer 74
Index

139

Caller ID 67
fax header and footer 67
fax quality 77
maximum sending speed 68
sender information 67
Transmit Terminal Identification
(TTI) 67
setting up fax
country-specific 63
digital telephone service 62
DSL connection 60
standard telephone line
connection 57
VoIP connection 61
setting up printer
faxing 73
on wireless network
(Windows) 82
settings timeout
disabling 20
setup troubleshooting
cannot print through USB 106
incorrect language appears on
display 102
page does not print 104
printer does not respond 105
printer printing blank pages 105
printhead error 102
software did not install 103
sharing printer in Windows 87
software
Service Center 101
software did not install 103
software updates
checking 25
enabling 25
speaker volume
adjusting 76
Speed Dial
setting up 70
splitter, choosing 74
SSID
ad hoc 84
finding 95
locating 89
wireless network 89
streaks or lines on printed
image 109
supported memory cards and file
types 37
supported operating systems 23

switching from USB
to wireless 87
switching from wireless
to USB 87

T
TCP/IP 97
technical support 101
temporary settings
changing into default 20
tips for
copying 47
printing 31
receiving faxes 72
scanning 52
sending faxes 71
top cover 12
transmission report, fax 78
transparencies 28
troubleshooting
checking an unresponsive
printer 101
contacting technical support 101
fax checklist 112
Service Center 101
solving basic printer
problems 101
wireless network 120
troubleshooting, copy
scanner unit does not close 110
troubleshooting, copy and scan
cannot scan to computer over a
network 111
copier or scanner does not
respond 110
partial document or photo
scans 111
poor scanned image quality 110
scan not successful 111
scanning takes too long or freezes
the computer 111
troubleshooting, fax
cannot receive faxes 115
cannot run fax software 116
cannot send faxes 113
error messages, printer control
panel 116
troubleshooting, jams and
misfeeds
paper jam in the ADF 107
paper jam in the paper
support 107

paper jam in the printer 106
paper or specialty media 108
troubleshooting, memory card
cannot print from a flash
drive 119
checklist 118
nothing happens when memory
card is inserted 118
troubleshooting, print
cannot delete documents from
print queue 106
computer slows down when
printing 110
poor quality at the edges of
page 108
slow print speed 109
streaks or lines on printed
image 109
troubleshooting, setup
cannot print through USB 106
incorrect language appears on
display 102
page does not print 104
printer does not respond 105
printer printing blank pages 105
printhead error 102
software did not install 103
troubleshooting, wireless
cannot print over wireless
network 121
changing wireless settings after
installation (Windows) 84
photos do not print from memory
card across wireless
network 119
resolving communication
problems 132
Wi-Fi indicator light is blinking
orange 127
Wi-Fi indicator light is not lit 124
Wi-Fi indicator light is still
orange 126
TX report, fax 78

U
UK
special wireless setup
instructions 83
uninstalling printer software 25
updating printer software 25
updating the application list 56
Index

140

USB 87, 95
cable 92
USB connection
with network connection 95
USB port 12
user information, fax
setting 68

V
Virtual Private Network 132
voice mail
setting up 57
voice mail, fax settings 76
Voice over Internet Protocol (VoIP)
fax setup 61
VoIP adapter 61
volume, adjusting
ringer and dial tone 76
speaker 76
VPN
lose connection to printer 132

W
Web site
finding 9
WEP 80
ad hoc 84
WEP key
key index 97
locating 89
Windows
installing printer on wireless
network 82
Windows software
Abbyy Sprint OCR 23
Fast Pics 23
Fax Setup Utility 23
Fax Solutions software 23
Printer Home 23
Printing Preferences 23
Service Center 23
Toolbar 23
Wireless Setup Utility 23
wireless 87, 95
printer does not print 124
troubleshooting 125, 132
wireless network
adding a printer to existing ad hoc
network 86
common home configurations 90

creating an ad hoc network using
Windows 84
information needed for setting up
wireless printing 81
installing printer on
(Windows) 82
interference 94
resolving communication
problems 132
security 80
security information 90
signal strength 93
SSID 89
troubleshooting 120
types of wireless networks 92
wireless network compatibility 80
wireless print server
not installed 130
wireless setup
information needed for 81
wireless signal
strength 93
wireless signal absorption 94
wireless troubleshooting
cannot print over wireless
network 121
changing wireless settings after
installation (Windows) 84
photos do not print from memory
card across wireless
network 119
printer and computer on different
networks 95
printer works intermittently on
wireless network 132
Wi-Fi indicator light is blinking
orange 127
Wi-Fi indicator light is not lit 124
Wi-Fi indicator light is still
orange 126
Wi-Fi indicator 11
description of colors 82
light is not lit 124
Wi-Fi indicator light is blinking
orange 127
Wi-Fi indicator light is green
printer does not print 125
Wi-Fi indicator light is still
orange 126
Wi-Fi Protected Setup 87
using 88

Wi-Fi Protected Setup logo
identifying 88
WPA 80
WPA passphrase
locating 89
WPA2 80
WPS 87

Index

141

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Format                          : application/pdf
Creator                         : Dell Inc.
Title                           : User's Guide
Subject                         : User's Guide
Description                     : User's Guide
Producer                        : Acrobat Distiller 9.0.0 (Windows); modified using iTextSharp 5.1.3 (c) 1T3XT BVBA
Keywords                        :  features#software #drivers#operation#paper#controls#clearing paper jams#resources#esuprt_printers_main#Dell V515w All In One Wireless Inkjet Printer#dell-v515w#User's Guide
Create Date                     : 2009:03:25 16:06:43-04:00
Creator Tool                    : XSL Formatter V3.4 MR5 (3,4,2006,0705) for Windows
Modify Date                     : 2012:10:30 12:38:54-05:00
Page Mode                       : UseOutlines
Page Count                      : 141
Author                          : Dell Inc.
Productcode                     : dell-v515w
Typecode                        : ug
Typedescription                 : User's Guide
Languagecodes                   : en-us
Sectioncode                     : 
Sectiondescription              : 
Publishdate                     : 2011-05-05 00:00:00
Expirydate                      : 9999-09-09 00:00:00
Manualurl                       : http://ftp.dell.com/manuals/all-products/esuprt_printers_main/esuprt_printers/dell-v515w_User's Guide_en-us.pdf
Readytocopy                     : false
Futureproductindication         : No
Categorypathforfutureproducts   : 
Businesskeywords                : V515w# features#software #drivers#operation#paper#controls#clearing paper jams#resources
Filesize                        : 5266
Creationdate                    : D:20090325160643-04'00'
Moddate                         : D:20121030113539-05'00'

EXIF Metadata provided by EXIF.tools

Dell V515W All In One Wireless Inkjet Printer Users Manual User's Guide

Navigation menu

Versions of this User Manual:

Views

Navigation