Dell W Ap214 215 Owners Manual AP214/215 Access Point Installation Guide
2014-11-13
: Dell Dell-W-Ap214-215-Owners-Manual-115262 dell-w-ap214-215-owners-manual-115262 dell pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dell Networking W-AP210 Series Wireless Access Point Installation Guide The Dell Networking W-AP210 Series (W-AP214 and W-AP215) wireless access points support the IEEE 802.11ac and 802.11n standards for high-performance WLAN. These access points use MIMO (Multiple-Input, Multiple-Output) technology and other high-throughput mode techniques to deliver highperformance, 802.11n 2.4 GHz and 802.11ac 5 GHz functionality while simultaneously supporting existing 802.11a/b/g wireless services. The W-AP210 Series access points work only in conjunction with a Dell Networking W-Series Mobility Controller. Figure 2 W-AP210 Series Side View (W-AP214 shown) ANT2 ANT1 standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE midspan injector, or network infrastructure that supports PoE. ANT0 The 10/100/1000 Mbps Ethernet port is on the bottom of the AP. The port has RJ-45 female connectors with the pin-outs shown in Figure 6. Figure 6 Gigabit Ethernet Port Pin-Out 1000Base-T Gigabit Ethernet Port The W-AP210 Series access point provides the following capabilities: 2 3 4 5 6 7 8 Wireless transceiver Protocol-independent networking functionality IEEE 802.11a/b/g/n/ac operation as a wireless access point IEEE 802.11a/b/g/n/ac operation as a wireless air monitor Compatibility with IEEE 802.3at PoE+ and 802.3af PoE External Antenna Connectors Central management configuration and upgrades through a controller The W-AP214 is equipped with three external antenna connectors. The connectors are labeled ANT0, ANT1, and ANT2, and correspond to radio chains 0, 1, and 2. Note: The W-AP210 Series access point requires Dell Networking W-Series ArubaOS 6.4.2.0 or later version. USB Port For optimal performance when using articulating direct-mount antennas, professional installers must orient the antennas with ANT0 and ANT2 at 45 degree angles and ANT1 oriented straight out (see Figure 3). Signal Name Function BI_DA+ BI_DABI_DB+ BI_DC+ BI_DCBI_DBBI_DD+ BI_DD- Bi-directional pair +A Bi-directional pair -A Bi-directional pair +B Bi-directional pair +C Bi-directional pair -C Bi-directional pair -B Bi-directional pair +D Bi-directional pair -D 12 VDC (+/- 5%)/18W Center-positive 1.7/4.0 mm circular plug, 9.5 mm length Reset Button 9/16" and 15/16” Ceiling Rail Adapters Installation Guide (this document) The reset button can be used to return the AP to factory default settings. To reset the AP: 2. Press and hold the reset button using a small, narrow object, such as a paperclip. retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. 3. Power-on the AP without releasing the reset button. The power LED will flash within 5 seconds. 4. Release the reset button. The power LED will flash again within 15 seconds indicating that the reset is completed. The AP will now continue to boot with the factory default settings. USB Interface 2.4GHz 5GHz ENET PWR The W-AP210 Series is equipped with a USB interface for connectivity with cellular modems. Before You Begin Note: The USB interface is disabled when the W-AP210 Series is powered from 802.3af PoE. Caution: FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). Figure 4 W-AP210 Series Bottom View LEDs Caution: EU Statement: The W-AP210 Series is equipped with four LEDs that indicate the status of the various components of the AP. PWR: Indicates whether or not the AP is powered-on ENET: Indicates the status of the AP Ethernet port 5 GHz: Indicates the status of the AP 802.11a/n radio 2.4 GHz: Indicates the status of the AP 802.11b/g/n radio LED Color/State Meaning PWR Off No power to AP Red Initial power-up Green - Flashing AP booting Green - Steady AP ready Off Ethernet link unavailable Yellow - Steady 10/100Mbps Ethernet link established Green - Steady 1000Mbps Ethernet link established Flashing Ethernet link activity Off 5 GHz radio disabled Yellow - Steady 5 GHz radio enabled in non-HT WLAN mode Green - Steady 5 GHz radio enabled in HT WLAN mode Flashing - Green 5 GHz Air or Spectrum Monitor Off 2.4 GHz radio disabled Yellow - Steady 2.4 GHz radio enabled in non-HT WLAN mode Green - Steady 2.4 GHz radio enabled in HT WLAN mode Flashing - Green 2.4 GHz Air or Spectrum Monitor ENET 5 GHz 2.4 GHz DHCP Server with vendor-specific options Successful setup of a W-AP210 Series access point consists of five tasks, which must be performed in this order: 1. Verify pre-installation connectivity. 2. Identify the specific installation location for each AP. 3. Install each AP. 4. Verify post-installation connectivity. 5. Configure each AP. Note: Dell, in compliance with governmental requirements, has designed the W-AP210 Series access points so that only authorized network administrators can change the settings. For more information about AP configuration, refer to the Dell Networking W-Series ArubaOS Quick Start Guide and Dell Networking W-Series ArubaOS User Guide. Caution: Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used. 1. Power off the AP. Note: Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, DNS server with an “A” record Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used to power this device, as long as it complies with all applicable local regulatory requirements and the DC interface meets the following specifications: W-AP214 or W-AP215 Access Point Figure 1 W-AP210 Series LEDs If PoE is not available, an optional Dell AP AC-DC adapter kit (sold separately) can be used to power the W-AP210 Series. W-AP210 Series Hardware Overview Aruba Discovery Protocol (ADP) Summary of the Setup Process DC Power Socket Figure 3 W-AP214 Antenna Orientation Package Contents RJ-45 Female Pin-Out 1 Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the Dell Networking W-Series ArubaOS User Guide for details on restrictions. Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au Dell Networking W-Series ArubaOS User Guide pour les details des restrictions. Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im Dell Networking W-Series ArubaOS User Guide. Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla Dell Networking W-Series ArubaOS User Guide per avere informazioni detagliate sulle restrizioni. Pre-Installation Network Requirements After WLAN planning is complete and the appropriate products and their placement have been determined, the Dell controller(s) must be installed and initial setup performed before the Dell APs are deployed. For initial setup of the controller, refer to the Dell Networking W-Series ArubaOS Quick Start Guide corresponding to the software version installed on your controller. AP Pre-Installation Checklist Console Port The serial console port allows you to connect the AP to a serial terminal or a laptop for direct local management. This port is an RJ-45 female connector with the pinouts described in . Connect it directly to a terminal or terminal server using an Ethernet cable. Ethernet Port Before installing your W-AP210 Series AP, ensure that you have the following: Figure 5 Serial Port Pin-Out Serial Console Port RJ-45 Female Pin-Out 1 2 3 4 5 6 7 8 Direction Input Output CAT5e or better UTP cable of required length One of the following power sources: TxD GND GND RxD W-AP210 Series is equipped with one 10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wired-network connectivity port. This port supports IEEE 802.3af and 802.3at Power over Ethernet (PoE) compliance, accepting 48 VDC (nominal) as a IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The POE source can be any power source equipment (PSE) controller or midspan PSE device Verifying Pre-Installation Connectivity Before you install APs in a network environment, make sure that the APs are able to locate and connect to the controller after power on. Specifically, you must verify the following conditions: When connected to the network, each AP is assigned a valid IP address APs are able to locate the controller Refer to the Dell Networking W-Series ArubaOS Quick Start Guide for instructions on locating and connecting to the controller. Identifying Specific Installation Locations You can mount the W-AP210 Series access point on a wall or on the ceiling. Use the AP placement map generated by Dell VisualRF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/ interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in VisualRF plan. Identifying Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed location. Examples of sources that degrade RF performance include: Cement and brick Objects that contain water Metal Microwave ovens Wireless phones and headsets Installing the AP Note: Service to all Dell products should be performed by trained service personnel only. Using the Ceiling Rail Adapter The W-AP210 Series ships with two ceiling rail adapters for 9/16” and 15/16” ceiling rails. Additional wall mount adapters and ceiling rail adapters for other rail styles are available as accessory kits. Caution: Make sure the AP fits securely on the ceiling tile rail when hanging the device from the ceiling, because poor installation could cause it to fall on people or equipment. Dell AP AC-DC adapter kit (sold separately) Dell Controller provisioned on the network: Layer 2/3 network connectivity to your access point One of the following network services: 1. Pull the necessary cables through a prepared hole in the ceiling tile where the AP will be placed. 2. Place the adapter against the back of the AP at an angle of approximately 30 degrees to the tabs (see Figure 7). 3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 7). Figure 7 Attaching the Ceiling Rail Adapter to the AP Power: 12 VDC power interface, supports powering through an AC-to-DC power adapter POE support on Ethernet ports: 802.3at-compliant and 802.3af-compliant POE sourcing devices Note: If a power adapter other than the one provided by Dell is used in US or Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum 1.5A, marked “LPS” and “Class 2,” and suitable for plugging into a standard power receptacle in US and Canada. FCC Class B Part 15 This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. For additional specifications on this product, please refer to the product data sheet on dell.com. Proper Disposal of Dell Equipment For the most current information about Global Environmental Compliance and Dell products, visit dell.com. Waste of Electrical and Electronic Equipment AP-110_04 Dell products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). 4. If necessary, connect the console cable to the console port on the back of the AP. China RoHS 5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-degree angle to the ceiling tile rail (see Figure 8). Make sure that any cable slack is above the ceiling tile. Dell products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left. 10 ᳝↦᳝ᆇ⠽䋼ໄᯢ Hazardous Materials Declaration 䚼ӊৡ⿄ (Parts) Figure 8 Mounting the AP ⬉䏃ᵓ (PCA Boards) ᴎẄ㒘ӊ (Mechanical Sub-Assemblies) ƻ˖ ᳝↦᳝ᆇ⠽䋼ܗ㋴(Hazardous Substance) 䬝 ݁Ӌ䫀 ⒈㘨㣃 &G &U 3%% 䪙 3E ∲ +J h ƻ ƻ ƻ ƻ ƻ h ƻ ƻ ƻ ƻ ƻ ⒈Ѡ㣃䝮 3%'( 㸼⼎䆹᳝↦᳝ᆇ⠽䋼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ䞣ഛ SJ/T11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard. h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ䖭ѯ⠽䋼DŽ This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ ՟བ⬉∴ऩܗഫ 䌈݊ѻકϞ ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼ѢѻકᰃѻકݠЁ᠔㾘ᅮⱘᴵӊϟᎹ The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. AP-110_005 European Union RoHS 7. On the W-AP214, install the external antennas according to the manufacturer’s instructions, and connect the antennas to the antenna interfaces on the AP. Connecting Required Cables Install cables in accordance with all applicable local and national regulations and practices. Verifying Post-Installation Connectivity The integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing successfully (see Table 1). Refer to the Dell Networking W-Series ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity. Configuring the AP AP Provisioning/Reprovisioning Provisioning parameters are unique to each AP. These local AP parameters are initially configured on the controller which are then pushed out to the AP and stored on the AP itself. Dell recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the Dell Networking W-Series ArubaOS User Guide for complete details. AP Configuration Configuration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the AP(s) but remain stored on the controller. Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to the Dell Networking W-Series ArubaOS User Guide and/or Dell Networking W-Series ArubaOS CLI Reference Guide for details. Product Specifications Electrical Ethernet: 1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface MDI/MDX IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T) Power over Ethernet (IEEE 802.3at and 802.3af compliant), 48V DC (nominal) and 56V DC (maximum)/350mA (see Figure 6 for pin configuration) Aruba Networks Inc., hereby, being the manufacturer of this product, declares that all CE Marked Dell wireless controller and access points product are manufactured in accordance to the provisional requirements set forth in the RoHS Directive 2011/65/EC. A copy of the Aruba Declaration of Conformity may be obtained upon request from: Aruba Networks Internatoinal Ltd, Building 1000, Citygate Mahon, Cork Ireland. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. EU Regulatory Conformance This product is CE marked according to the provisions of the R & TTE Directive (1999/5/EC) - CE(!). Dell hereby declares that the APIN0214 / APIN0215 device models are in compliance with the essential requirements and other relevant provisions of Directive 1999/ 5/EC -CE(!) Canada Contact Information dell.com/contactdell Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Support Website dell.com/support Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Documentation Website dell.com/support/manuals Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. (i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Note: Aucune émission n’est permise dans la bande 5 600-5 650 MHz. Jusqu’à nouvel avis, les dispositifs visés par la présente annexe ne doivent pas être en mesure d’émettre dans la bande 5 600-5 650 MHz, afin de protéger les radars météorologiques d’Environnement Canada exploités dans cette bande. The following regulatory model names apply to the W-AP210 Series: W-AP214: APIN0214 W-AP215: APIN0215 Copyright © 2014 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba Wireless Networks®, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners. Caution: RF Déclaration sur la radioexposition: Cet équipement est conforme aux normes IC Limites d'exposition aux rayonnements RF. Cet équipement doit être installé et utilisé à une distance minimum de 7,9 pouces (20 cm) entre l'radiateur et votre corps pour 2,4 GHz et 5 GHz opérations. cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou émetteur. This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India. Regulatory Model Names Web Site Support dell.com India RoHS Note: For country specific restrictions and additional safety and regulatory information, refer to the multi-language Dell Networking W-Series Safety, Environmental, and Regulatory Information document included with your Dell controller. Contacting Dell Main Website Please include the regulatory model number located on the product’s regulatory nameplate with the request. Safety and Regulatory Compliance Installation Guide This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause interference harmful to radio communications. The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at dell.com. 6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks into place on the ceiling tile rail. Dell Networking W-AP210 Series Wireless Access Point Open Source Code Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used can be found at this site: http://www.arubanetworks.com/open_source Includes software from Litech Systems Design. The IF-MAP client library copyright 2011 Infoblox, Inc. All rights reserved. This product includes software developed by Lars Fenneberg, et al. Legal Notice Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. End product system, including power supply, must be evaluated to IEC 60601-1-1 and IEC 60601-1 by the end user. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Dell approval. The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors’ VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors. 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原設計之特性及功能。 第十四條 FCC 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有 This device is electronically labeled. To view the FCC ID: 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 1. 前項合法通信，指依電信法規定作業之無線電通信。 Log into the controller WebUI. 2. Navigate to Maintenance > Controller > About. Caution: Dell access points must be installed by a professional installer. Theprofessional 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電 機設備之干擾。 installer is responsible for ensuring that grounding is available and it meets applicable local and national electrical codes. Caution: RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with cochannel Mobile Satellite Systems. www.dell.com Dell Networking W-AP210 Series Wireless Access Point | Installation Guide Part Number 0511515-01 | June 2014
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Language : en Format : application/pdf Creator : Dell Inc. Title : W-AP214/215 Access Point Installation Guide Subject : Deployment Guide Description : Deployment Guide Producer : Acrobat Distiller 11.0 (Windows); modified using iTextSharp 5.1.3 (c) 1T3XT BVBA Keywords : W-AP214/215 Access Point Installation Guide#esuprt_ser_stor_net#esuprt_networking#W-AP214/215#powerconnect-w-ap-214-215#Deployment Guide Create Date : 2009:07:01 14:54:10Z Creator Tool : FrameMaker 12.0 Modify Date : 2014:09:16 00:00:56-05:00 Page Mode : UseNone Page Count : 2 Author : Dell Inc. Productcode : powerconnect-w-ap-214-215 Typecode : dg Typedescription : Deployment Guide Languagecodes : en-us Sectioncode : Sectiondescription : Publishdate : 2014-09-16 00:00:00 Expirydate : 9999-09-09 00:00:00 Manualurl : ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_networking/esuprt_net_wireless/powerconnect-w-ap-214-215_Deployment%20Guide_en-us.pdf Readytocopy : false Futureproductindication : No Categorypathforfutureproducts : Businesskeywords : W-AP214/215 Access Point Installation Guide Filesize : 831 Isrestricted : False Productpath : Creationdate : D:20090701145410Z Moddate : D:20140915071915-05'00'EXIF Metadata provided by EXIF.tools