Dell Edge Gateway 3000 Series 3002 Installation And Operation Manual User 3001 User's Guide2 En Us
User Manual: Dell dell-edge-gateway-3000-series Dell Edge Gateway 3001 Installation and Operation Manual
Open the PDF directly: View PDF 
.
Page Count: 77
| Download | |
| Open PDF In Browser | View PDF |
Dell Edge Gateway 3002 Installation and Operation Manual Computer Model: Dell Edge Gateway 3002 Regulatory Model: N03G Regulatory Type: N03G001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners. 2017 - 08 Rev. A01 Contents 1 Overview......................................................................................................................... 5 2 System views.................................................................................................................. 6 Top view............................................................................................................................................................................. 6 Bottom view....................................................................................................................................................................... 7 Left view.............................................................................................................................................................................7 Right view.........................................................................................................................................................................10 3 Installing your Edge Gateway..........................................................................................11 Safety and regulatory information...................................................................................................................................... 11 Professional installation instructions............................................................................................................................ 12 Instructions d'installation professionnelles................................................................................................................... 12 Federal Communication Commission interference statement...................................................................................... 12 Industry Canada statement......................................................................................................................................... 13 Setting up your Edge Gateway..........................................................................................................................................14 Activating your mobile broadband service......................................................................................................................... 19 Mounting your Edge Gateway.......................................................................................................................................... 20 Mounting the Edge Gateway using the standard-mount bracket................................................................................20 Mounting the Edge Gateway using quick-mount bracket............................................................................................27 Attaching the cable control bars to the standard-mount bracket............................................................................... 35 Mounting the Edge Gateway on a DIN rail using the DIN-rail bracket......................................................................... 38 Mounting the Edge Gateway using the perpendicular mount...................................................................................... 41 Mounting the Edge Gateway using a VESA mount.....................................................................................................44 4 Setting up the ZigBee dongle........................................................................................ 46 5 Setting up the operating system................................................................................... 47 Windows 10 IoT Enterprise LTSB 2016..............................................................................................................................47 Boot up and login – Remote system configuration..................................................................................................... 47 Boot up and login—Static IP system configuration.....................................................................................................47 Restoring Windows 10 IoT Enterprise LTSB 2016....................................................................................................... 48 Windows 10 IOT Enterprise LTSB 2016 basic functions.............................................................................................. 48 Ubuntu Core 16................................................................................................................................................................ 49 Overview....................................................................................................................................................................49 Boot up and log in – Remote system configuration.................................................................................................... 50 Boot up and log in – Static IP system configuration................................................................................................... 50 Updating operating system and applications.............................................................................................................. 50 Additional Ubuntu commands......................................................................................................................................51 Network communication interfaces............................................................................................................................52 Additional communication interfaces.......................................................................................................................... 55 Security......................................................................................................................................................................56 Watchdog Timer (WDT)............................................................................................................................................. 57 3 Restoring Ubuntu Core 16.......................................................................................................................................... 57 Flashing a new OS image........................................................................................................................................... 58 Creating the recovery USB flash drive............................................................................................................................. 59 Edge Gateway CAN module functionality......................................................................................................................... 59 6 Accessing and updating BIOS........................................................................................ 61 Accessing BIOS settings................................................................................................................................................... 61 Entering BIOS setup during POST.............................................................................................................................. 61 Updating BIOS.................................................................................................................................................................. 61 Using the USB invocation script................................................................................................................................. 62 Updating the BIOS on a Windows system.................................................................................................................. 62 Using UEFI capsule update on an Ubuntu system...................................................................................................... 62 Dell Command | Configure (DCC).............................................................................................................................. 63 Edge Device Manager (EDM).................................................................................................................................... 63 Default BIOS settings....................................................................................................................................................... 63 System configuration (BIOS level 1)........................................................................................................................... 63 Security (BIOS level 1)................................................................................................................................................64 Secure boot (BIOS level 1)......................................................................................................................................... 65 Performance (BIOS level 1)........................................................................................................................................ 66 Power management (BIOS level 1)............................................................................................................................. 66 POST behavior (BIOS level 1).....................................................................................................................................66 Virtualization support (BIOS level 1)........................................................................................................................... 67 Maintenance (BIOS level 1).........................................................................................................................................67 System logs (BIOS level 1)..........................................................................................................................................67 7 References.................................................................................................................... 68 8 Appendix....................................................................................................................... 69 Antenna specifications..................................................................................................................................................... 69 De-mounting from DIN-rail bracket...................................................................................................................................70 Connecting to the Edge Gateway..................................................................................................................................... 71 Windows 10 IoT Enterprise LTSB 2016........................................................................................................................ 71 Ubuntu Core 16........................................................................................................................................................... 71 Default BIOS settings....................................................................................................................................................... 72 System configuration (BIOS level 1)............................................................................................................................72 Security (BIOS level 1)................................................................................................................................................73 Secure boot (BIOS level 1)..........................................................................................................................................74 Performance (BIOS level 1).........................................................................................................................................74 Power management (BIOS level 1)............................................................................................................................. 75 POST behavior (BIOS level 1)..................................................................................................................................... 75 Virtualization support (BIOS level 1)........................................................................................................................... 75 Maintenance (BIOS level 1)........................................................................................................................................ 76 System logs (BIOS level 1)..........................................................................................................................................76 9 Contacting Dell..............................................................................................................77 4 1 Overview The Edge Gateway 3000 Series is an Internet-of-Things (IoT) device. It is mounted at the edge of a network, enabling you to collect, secure, analyze, and act on data from multiple devices and sensors. It enables you to connect with devices used in transportation, building automation, manufacturing, and other applications. The Edge Gateway has a low-power architecture, which is capable of supporting industrial automation workloads while remaining fanless to satisfy environmental and reliability requirements. It supports Windows 10 IoT Enterprise LTSB 2016 and Ubuntu Core 16 operating systems. 5 2 System views Top view Table 1. Top view Features 1 WLAN, Bluetooth, or GPS connector Connect the antenna to increase the range and strength of wireless, Bluetooth, or satellite signals. 2 Mobile broadband antenna-connector one (3G/ LTE) Connect the mobile broadband antenna to increase the range and strength of mobile broadband signals. 3 ZigBee antenna connector Connect the ZigBee antenna for intermittent data transmissions from a ZigBee-compliant sensor or input device. 4 Mobile broadband antenna-connector two (LTE Auxiliary only) Connect the mobile broadband antenna to increase the range and strength of mobile broadband signals. NOTE: Depending on the configuration ordered, some of the antenna connectors may not be present or may be capped. For more information about connecting antennas to the Edge Gateway, see the documentation that is shipped with the antenna. 6 Bottom view Table 2. Bottom view Features 1 Service Tag label The Service Tag is a unique alphanumeric identifier that enables the Dell service technicians to identify the hardware components in your Edge Gateway and access warranty information. 2 Earth ground A large conductor attached to one side of the power supply, which serves as the common return path for current from many different components in the circuit. Left view Table 3. Left view Features 1 Intrusion switch An intrusion event is triggered when the enclosure (in which the Edge Gateway is installed) is opened. NOTE: External enclosure is sold separately. 7 Features NOTE: An intrusion event is triggered by a third-party enclosure to the Edge Gateway through a sensor. The sensor should have a cable that is compatible with the intrusion switch connector on the Edge Gateway. 2 Power or ignition port Connect a 12-57 VDC (1.08-0.23 A) power cable to supply power to the Edge Gateway. NOTE: Power cable is sold separately. NOTE: For marine applications, limit input voltage to 12-48 VDC. The cable length for rail applications must not exceed 30 meters. 3 Power and System status light Indicates the power status and system status. 4 WLAN or Bluetooth status light Indicates if WLAN or Bluetooth is ON or OFF. 5 Cloud-connection status light Indicates the cloud connection status. 6 Ethernet port one (with Power over Ethernet support) Connect an Ethernet (RJ45) cable to gain network access. Provides data transfer speeds up to 10/100 Mbps and supports Alternative A of the IEEE 802.3af standard. NOTE: The Edge Gateway is an IEEE 802.3af Alternative A compliant Powered Device (PD). NOTE: To comply with EU Declaration of Conformity (DoC), ensure cable length from the system to the device does not exceed 30 meters. NOTE: To comply with regulatory requirements in Brazil, ensure cable length from the system to the device does not exceed 10 meters. 7 USB 3.0 port 1 Connect a USB enabled device. Provides data transfer speeds up to 5 Gbps. 8 SIM card slot (optional) Insert a micro-SIM card into the slot. 9 SD card slot (optional) Insert a micro-SD card into the slot. NOTE: Remove the SD card slot filler before inserting a micro-SD card. 10 Quick Resource Locator label Scan with a QR reader to access documentation and other system information. 11 micro-SIM or micro-SD card access door Open the access door to access the micro-SIM or micro-SD card. 1 USB power is limited to 0.6 A/3 W. Table 4. Status-light indicators Function Indicator Color Control Status System Power status and System status Green or Amber BIOS Off: System off On (Solid Green): System on or Boot successful On (Solid Amber): Power up or boot fail Blinking Amber: Fault or error 8 Function Indicator Color Control Status WLAN or Bluetooth Green Hardware Off: WLAN or Bluetooth module is off On: WLAN or Bluetooth module is on Cloud Green Software Off: No connection to the cloud device or service On: Edge Gateway connected to a cloud device or service Blinking Green: Activity to a cloud device or service LAN (RJ-45) Link Green/Amber Driver (LAN) Off: No network link or cable is not connected On (Green): High-speed connection (100 Mbps) On (Amber): Low-speed connection (10 Mbps) Activity Green Driver (LAN) Off: No activity on link Blinking Green: LAN activity. The blink rate is related to packet density. NOTE: The power and system status light may operate differently during different boot-up scenarios, for example, when a USB script file is run during boot-up. Table 5. Power connector pin definition details Pin Signal Function 1 DC+ 12–57 VDC power 2 DC– Ground 3 IG 9–32 VDC ignition NOTE: Pin 3 (IG) is connected to the vehicle's ignition status indicator (optional) or a wake pin. A voltage of more than 9 V on the signal indicates that the vehicle’s engine is running. The Ignition or Wake pin is used to prevent the draining of the vehicle battery when the vehicle is turned off for an extended amount of time. 9 NOTE: The IG signal can be used to gracefully shutdown or enter low-power state when the vehicle is turned off (battery powered). It can also be used for powering on the Edge Gateway when the vehicle starts. Right view Table 6. Right view—3002 Features 1 CANbus port Enables the CANbus connection. 2 USB 2.0 port 1 Connect a USB enabled device. Provides data transfer speeds up to 480 Mbps. 3 Ethernet port two (Non-PoE) Connect an Ethernet (RJ45) cable for network access. Provides data transfer speeds up to 10/100 Mbps. 1 USB power is limited to 0.4 A/2 W. Table 7. CANbus-port pin definition details Features 1 GND Ground 2 CAN-H High-level CANbus line 3 CAN-L Low-level CANbus line 10 3 Installing your Edge Gateway WARNING: Before you begin any of the procedures in this section, read the safety and regulatory information that is shipped with your system. For additional best practices information, go to www.dell.com/regulatory_compliance. Safety and regulatory information WARNING: The Edge Gateway must be installed by knowledgeable, skilled persons familiar with local and/or international electrical codes and regulations. WARNING: The Edge Gateway is not designed for use in wet environments. If the Edge Gateway is to be installed in a wet environment, depending on the location and environment, it must be installed in a panel box or enclosure with an Ingress Protection (IP) rating of IP54, IP65, or higher. WARNING: To reduce the risk of electric shock, power to the DC+ and DC- terminals must be provided by a power supply or transformer/rectifier circuit that is designed with double-insulation. The power supply or power circuit source must comply with local codes and regulations; for example, in the USA, NEC Class 2 (SELV/limited energy circuit, or LPS circuitry). If powered by a battery, double-insulation is not required. WARNING: When installing the Edge Gateway, the responsible party or integrator shall use the 12-57 VDC or Power over Ethernet (PoE) power source 37-57 VDC, with a minimum of 13 W power already present as part of the client’s installation. WARNING: Ensure that the power source providing power to the Edge Gateway is reliably grounded and filtered such that the peak-to-peak ripple component is less than 10 percent of the input DC voltage. WARNING: When installing the Edge Gateway 3001 and 3002, use a cable appropriate for the load currents: 3-core cable rated 5 A at 90°C (194°F) minimum, which conform to either IEC 60227 or IEC 60245. The system accepts cables from 0.8 mm to 2 mm. The maximum operating temperature of the Edge Gateway is 70⁰C (158°F). Do not exceed this maximum temperature while operating the Edge Gateway inside an enclosure. Internal heating of the Edge Gateway electronics, other electronics, and the lack of ventilation inside an enclosure can cause the operating temperature of the Edge Gateway to be greater than the outside ambient temperature. Continuous operation of the Edge Gateway at temperatures greater than 70⁰C (158°F) may result in an increased failure rate and a reduction of the product life. Ensure that the maximum operating temperature of the Edge Gateway when placed inside an enclosure is 70⁰C (158°F) or less. WARNING: Always ensure that the available power source matches the required input power of the Edge Gateway. Check the input power markings next to power connector(s) before making connections. The 12-57 VDC (1.08-0.23 A) or the PoE power source must be compliant with local Electrical Codes and Regulations. WARNING: To ensure the protection provided by the Edge Gateway is not impaired, do not use or install the system in any manner other than what is specified in this manual. WARNING: If a battery is included as part of the system or network, the battery must be installed within an appropriate enclosure in accordance with local fire and electrical codes and laws. WARNING: The system is for installation in a suitable industrial enclosure (provides electrical, mechanical, and fire hazard protection). WARNING: The core module only can be wall-mounted (without the need for an additional enclosure). 11 Professional installation instructions Installation personnel This product is designed for specific applications and needs to be installed by qualified personnel with RF and regulatory-related knowledge. The general user shall not attempt to install or change the setting. Installation location The product shall be installed at a location where the radiating antenna is kept 20 cm from nearby persons in its normal operation condition in order to meet regulatory RF exposure requirements. External antenna Use only approved antenna(s). Non-approved antenna(s) may produce spurious or excessive RF transmitting power which may lead to a violation of FCC/IC limits. Installation procedure Refer to user’s manual for installation instructions. WARNING: Carefully select the installation position and make sure that the final output power does not exceed the limits described in the product’s documentation. The violation of these rules could lead to serious federal penalties. Instructions d'installation professionnelles Le personnel d'installation Ce produit est conçu pour des applications spécifiques et doit être installé par un personnel qualifié avec RF et connaissances connexes réglementaire. L'utilisateur ne doit pas tenter générale d'installer ou de modifier le réglage. Lieu d'installation Le produit doit être installé à un endroit où l'antenne de rayonnement est maintenue à 20 cm de personnes à proximité dans son état de fonctionnement normal, afin de répondre aux exigences réglementaires d'exposition aux radiofréquences. Antenne externe Utilisez uniquement l'antenne(s) qui ont été approuvés par le demandeur. Antenne (s) peuvent produire de l'énergie RF parasite indésirable ou excessive transmission qui peut conduire à une violation des normes de la FCC / IC est interdite et non-approuvé. Procédure d'installation ATTENTION: S'il vous plaît choisir avec soin la position d'installation et assurez-vous que la puissance de sortie final ne dépasse pas les limites fixées dans les règles pertinentes. La violation de ces règles pourrait conduire à des sanctions fédérales graves. Federal Communication Commission interference statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 12 may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC caution: • Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation exposure statement: This equipment complies with FCC radiation exposure limits for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the active transceiver and your body. NOTE: The country code selection is for a non-US model only and is not available to all US model. Per FCC regulation, all WiFi products marketed in the US must be fixed to US operation channels only. Industry Canada statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, the radio transmitter(s) may only operate using an antenna(s) of a type and maximum (or lesser) gain approved for the transmitter(s). To reduce potential radio interference to other users, the antenna type(s) and gain(s) should be chosen so that the Equivalent Isotropic Radiated Power (E.I.R.P.) is not more than what was approved for the transmitter(s). This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. This device complies with RSS-210 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. Cet appareil est conforme à la norme RSS-210 d'Industrie Canada. L'opération est soumise à la condition que cet appareil ne provoque aucune interférence nuisible. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées. The County Code Selection feature is disabled for products marketed in the US/Canada. 13 La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au Canada. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the active transceiver and your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Setting up your Edge Gateway NOTE: Edge Gateway mounting options are sold separately. NOTE: Mounting can be done before or after configuring your Edge Gateway. For more information about mounting your Edge Gateway, see Mounting your Edge Gateway. NOTE: In some environments where the Edge Gateway may be installed, a more robust mounting method is required. For example, for mounting in marine applications, it is recommended to use only the standard— mount bracket. The recommendation is due to the presence of vibrations unique to the marine environment. 1. Connect an Ethernet cable to Ethernet port one. 2. Connect the antennas depending on the configuration ordered (optional). NOTE: The antennas supported in the Edge Gateway vary depending on the configuration ordered. Table 8. Antennas supported in Edge Gateway 3002 Antennas supported Signals 14 3002 Yes Yes Yes Yes Yes NOTE: Use only the supplied antennas or third-party antennas that meet the minimum specifications. NOTE: Depending on the configuration ordered, some of the antenna connectors may not be present or may be capped. NOTE: Mobile broadband antenna connector two is for LTE Auxiliary only; it does not support 3G. 3. Insert the antenna into the connector. NOTE: If you are installing multiple antennas, follow the sequence indicated in the following image. 4. Secure the antenna by tightening the rotating head of the connector until it firmly holds the antenna in the preferred position (upright or straight). NOTE: Antenna images are for illustrative purposes only. Actual appearance may differ from the images provided. 5. Connect all desired cables to the appropriate I/O ports on the Edge Gateway. 6. Open the micro-SIM or micro-SD card access door. 15 7. Insert a micro-SIM card into the top micro-SIM card slot and activate your mobile broadband service. CAUTION: Dell recommends that you insert the micro-SIM card before turning on the Edge Gateway. NOTE: Ensure that you firmly screw back the access door after closing. NOTE: Contact your service provider to activate your micro-SIM card. 8. Insert a micro-SD card into the bottom micro-SD card slot. NOTE: Remove the SD card slot filler before inserting a micro-SD card. NOTE: Ensure that you firmly screw back the access door after closing. 9. 16 Connect a grounding cable between the Edge Gateway and the secondary enclosure. NOTE: Secondary enclosures are sold separately. 10. Connect the Edge Gateway to one of the following power sources: • DC-IN • PoE 17 NOTE: Shut down your system before you change the power sources. 11. Replace the dust caps on any unused ports. 12. When setting up the Edge Gateway for the first time, complete the operating system setup. For more information, see Setting up your operating system. NOTE: MAC addresses and the IMEI number are available on the label at the front of the Edge Gateway. Remove the label at install. NOTE: The Edge Gateway is shipped with either Windows 10 IoT Enterprise LTSB 2016 or Ubuntu Core 16 operating system. NOTE: The default user name and password for Windows 10 IoT Enterprise LTSB 2016 is admin. NOTE: The default user name and password for Ubuntu Core 16 is admin. 13. Access the BIOS by connecting remotely with the Dell Command | Configure application. Windows 10 IOT Enterprise LTSB 2016 Click Start → All Programs → Dell → Command Configure → Dell Command | Configure Wizard. Ubuntu Core 16 Use the dcc.cctk command to access the Dell Command | Configure application. NOTE: For more information about using the Dell Command | Configure application, see the Dell Command | Configure Installation Guide and User's Guide at www.dell.com/dellclientcommandsuitemanuals. NOTE: For more information about BIOS settings on the Edge Gateway, see Default BIOS settings. 14. Install the Edge Gateway using one of the following mounting options: NOTE: An open space of 63.50 mm (2.50 in) is recommended around the Edge Gateway for optimal air circulation. 18 • Standard mount • DIN rail mount • Quick mount • Perpendicular mount • Cable control bar • VESA mount Activating your mobile broadband service CAUTION: Before you power on the Edge Gateway, insert a micro-SIM card. NOTE: Ensure that the service provider has already activated the micro-SIM card before you use it in the Edge Gateway. 1. Remove the screw to open the micro-SIM card access door. 2. Insert a micro-SIM card into the top micro-SIM card slot. 3. Replace the screw, and close the micro-SIM card access door. 4. Power on the Edge Gateway. 5. Connect to a mobile network. Windows operating system a. Click the network icon from the taskbar, and then click Cellular. b. Select Mobile Broadband Carrier → Advanced Options. c. Make a note of the International Mobile Equipment Identity (IMEI) and Integrated Circuit Card Identifier (ICCID). d. Enter your APN number and any other credentials that your service provider requires. Ubuntu operating system a. Open the Terminal window. b. Enter $sudo su - to access super user mode. c. Configure the Mobile Broadband connection profile: Command line: network-manager.nmcli con add typeifname con-name apn Example (Verizon): network-manager.nmcli con add type gsm ifname cdc-wdm0 con-name VZ_GSMDEMO apn vzwinternet 19 Example (AT&T): network-manager.nmcli con add type gsm ifname cdc-wdm0 con-name ATT_GSMDEMO apn broadband Example (3G): network-manager.nmcli con add type gsm ifname cdc-wdm0 con-name 3G_GSMDEMO apn internet d. Connect to the mobile network: Command line: network-manager.nmcli con up Example (Verizon): network-manager.nmcli con up VZ_GSMDEMO Example (AT&T): network-manager.nmcli con up ATT_GSMDEMO Example (3G): network-manager.nmcli con up 3G_GSMDEMO To disconnect from the mobile network: Command line: network-manager.nmcli con down Example (Verizon): network-manager.nmcli con down VZ_GSMDEMO Example (AT&T): network-manager.nmcli con down ATT_GSMDEMO Example (3G): network-manager.nmcli con down 3G_GSMDEMO Mounting your Edge Gateway NOTE: Mounting can be completed before or after configuring your Edge Gateway. NOTE: Mounting options are sold separately. Mounting instructions are available in the documentation shipped with the mounting device. NOTE: In some environments where the Edge Gateway is installed, a more robust mounting method is required. For example, in marine applications, due to vibrations unique to that environment, only standard-mount bracket should be used. Mounting the Edge Gateway using the standard-mount bracket Mounting dimensions 20 NOTE: The mounting brackets are shipped with only those screws that are required for securing the mounting brackets to the Edge Gateway. 1. Secure the standard-mount bracket to the back of the Edge Gateway using the four M4x4.5 screws. NOTE: Torque the screws at 8±0.5 kilograms-centimeter (17.64±1.1 pounds-inch). 21 2. 22 Place the Edge Gateway against the wall, and align the holes in the standard-mount bracket with the holes on the wall. Screw holes on the bracket have a diameter of 3 mm (0.12 in). 3. Place the standard-mount bracket on the wall, and using the holes above the screw holes on the bracket, mark the positions to drill the four holes. 23 4. Drill four holes in the wall as marked. 5. Insert and tighten four screws (not supplied) to the wall. NOTE: Purchase screws that fit the diameter of the screw holes. 24 6. Align the screw holes on the standard-mount bracket with the screws and place the Edge Gateway onto the wall. 25 7. 26 Tighten the screws to secure the assembly to the wall. Mounting the Edge Gateway using quick-mount bracket The quick-mount bracket is a combination of the standard-mount bracket and the DIN-rail bracket. It enables you to easily mount and demount the Edge Gateway. NOTE: The mounting brackets are shipped with only those screws required for securing the mounting brackets to the Edge Gateway. Mounting dimensions 27 Mounting instructions 1. 28 Place the standard-mount bracket on the wall, and using the holes above the screw holes on the bracket, mark the positions to drill the four holes. 2. Drill four holes in the wall as marked. 3. Insert and tighten four screws (not supplied) to the wall. NOTE: Purchase screws that fit the diameter of the screw holes. 29 4. 30 Align the screw holes on the standard-mount bracket with the screws on the wall, letting the bracket hang on the screws. 5. Tighten the screws to secure the assembly to the wall. 31 6. Align the screw holes on the DIN-rail bracket with the screw holes at the back of the Edge Gateway. 7. Place the two M4x7 screws on the DIN-rail bracket and secure it to the Edge Gateway. 32 8. Place the Edge Gateway on the standard mount at an angle, and then pull the Edge Gateway down to compress the springs at the top of the DIN-rail bracket. 33 9. 34 Push the Edge Gateway towards the DIN-rail to secure it on the standard-mount bracket. NOTE: For more information about demounting the DIN-rail, see Demounting DIN rail. Attaching the cable control bars to the standard-mount bracket 1. Mount the Edge Gateway on the wall using the standard-mount bracket or quick-mount bracket. 2. Place the cable control bar on the mounting bracket and secure it to the notch. CAUTION: Use the top cable control bar only with coaxial cable connections. Do not use with antennas. 35 3. Align the screw holes on the cable control bar with the screw holes on the mounting bracket. 4. Tighten the six M3 x 3.5 mm screws that secure the cable control bar to the mounting bracket. NOTE: Torque the screws at 5±0.5 kilograms-centimeter (11.02±1.1 pounds-inch). 36 5. Connect the cables to the Edge Gateway. 6. Loop the cable lock (not supplied) to secure each cable to the cable control bar. 37 Mounting the Edge Gateway on a DIN rail using the DIN-rail bracket NOTE: The DIN-rail bracket includes the screws that are required for securing the bracket to the Edge Gateway. 1. Align the screw holes on the DIN-rail bracket with the screw holes at back of the Edge Gateway. 2. Place the two M4x7 screws on the DIN-rail bracket and secure it to the Edge Gateway. 38 3. Secure the DIN-rail mounting bracket to the Edge Gateway using the two M4x7 screws provided. NOTE: Torque the screws at 8±0.5 kilograms-centimeter (17.64±1.1 pounds-inch) on the DIN-rail mounting bracket. 39 4. Place the Edge Gateway on the DIN rail at an angle, and then pull the Edge Gateway down to compress the springs at the top of the DIN-rail mounting bracket. 5. Push the Edge Gateway towards the DIN-rail to secure the lower clip of the bracket onto the DIN rail. 40 NOTE: For more information about demounting the DIN-rail, see Demounting DIN rail. Mounting the Edge Gateway using the perpendicular mount NOTE: The perpendicular mount is designed for mounting in a DIN-rail only. NOTE: An open space of 63.50 mm (2.50 in) around the Edge Gateway is recommended for optimal air circulation. Ensure that the environmental temperature in which the Edge Gateway is installed does not exceed the operating temperature of the Edge Gateway. For more information about the operating temperature of the Edge Gateway, see the Edge Gateway Specifications. 1. Align the screw holes on the perpendicular-mount bracket with the screw holes on the Edge Gateway. 2. Tighten the four M4x7 screws to secure the Edge Gateway to the perpendicular-mount bracket. NOTE: Torque the screws at 8±0.5 kilograms-centimeter (17.64±1.1 pounds-inch). 41 3. Align the screw holes on the DIN-rail mount bracket with the screw holes on the perpendicular-mount bracket, and tighten the two screws. NOTE: Torque the screws at 8±0.5 kilograms-centimeter (17.64±1.1 pounds-inch). 42 4. Place the Edge Gateway on the DIN rail at an angle and push the Edge Gateway down to compress the springs on the DIN-rail mount brackets. 5. Push the Edge Gateway towards the DIN-rail to secure the lower clip of the bracket onto the DIN rail. 43 6. Secure the Edge Gateway on the DIN rail. Mounting the Edge Gateway using a VESA mount The Edge Gateway can be mounted on a standard VESA mount (75 mm x 75 mm). NOTE: The VESA mount option is sold separately. For VESA mounting instructions, see the documentation that is shipped with the VESA mount. 44 45 4 Setting up the ZigBee dongle CAUTION: Do not connect the ZigBee dongle if the Edge Gateway is installed inside the enclosure. 1. Power off your Edge Gateway. 2. Connect the ZigBee dongle to any external USB port on your Edge Gateway. 3. Power on your Edge Gateway and complete the setup. NOTE: For more information about the ZigBee development, see www.silabs.com. 46 5 Setting up the operating system CAUTION: To prevent operating system corruption from sudden power loss, use the operating system to gracefully shut down the Edge Gateway. The Edge Gateway is shipped with one of the following operating systems: • Windows 10 IoT Enterprise LTSB 2016 • Ubuntu Core 16 NOTE: For more information about Windows 10 operating system, see msdn.microsoft.com. NOTE: For more information about the Ubuntu Core 16 operating system, see www.ubuntu.com/desktop/snappy. Windows 10 IoT Enterprise LTSB 2016 Boot up and login – Remote system configuration NOTE: Your computer must be on the same subnet as the Edge Gateway. 1. Connect a network cable from Ethernet port one on the Edge Gateway to a DHCP-enabled network or router that provides IP addresses. NOTE: The first-time boot to Windows takes about 5 minutes for system configuration. Subsequent boot-ups take about 50 seconds. 2. Using the MAC address provided on the front cover of the Edge Gateway, obtain the IP address through your network’s DHCP server or through a network analyzer. 3. On the Windows computer, search for Remote Desktop Connection and launch the application. 4. Log in using the IP address. NOTE: Ignore any certification errors when connecting to your Edge Gateway. Boot up and login—Static IP system configuration NOTE: To help set up the Edge Gateway remotely, the static IP address of Ethernet port two on the Edge Gateway is set to these values at the factory: • IP address: 192.168.2.1 • Subnet mask: 255.255.255.0 • DHCP server: Not applicable You can connect your Edge Gateway to a Windows computer that is on the same subnet using a crossover cable. 1. On the Windows computer, search for View network connections in the control panel. 2. In the list of network devices displayed, right-click the Ethernet adaptor that you want to use to connect to the Edge Gateway, then click Properties. 3. On the Networking tab, click Internet Protocol Version 4 (TCP/IPv4) → Properties. 4. Select Use the following IP address, then enter 192.168.2.x (where x represents the last digit of the IP address, for example, 192.168.2.2). 47 NOTE: Do not set the IPv4 address to the same IP address as the Edge Gateway. Use an IP address between 192.168.2.2 to 192.168.2.254. 5. Enter the subnet mask 255.255.255.0 , then click OK. 6. Secure a crossover network cable between Ethernet port two on the Edge Gateway and the configured Ethernet port on the computer. 7. On the Windows computer, launch Remote Desktop Connection. 8. Connect to the Edge Gateway using the IP address 192.168.2.1. The default username and password are both admin. Restoring Windows 10 IoT Enterprise LTSB 2016 CAUTION: These steps will delete all the data on your Edge Gateway. You can restore Windows 10 IoT Enterprise LTSB 2016 by using a USB flash drive. Prerequisites Create the recovery USB flash drive. For more information, see Creating the recovery USB flash drive. Procedure 1. Connect the recovery USB flash drive to the Edge Gateway. 2. Power on the Edge Gateway. The Edge Gateway will automatically boot from the USB recovery flash drive and restore Windows back to the factory image. Restoration takes about 25 minutes to complete and a confirmation log file is stored on the USB flash drive. Once restoration is complete, the system will power off. NOTE: The confirmation log file is named _ _
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Dell Create Date : 2017:08:11 03:39:44+00:00 Modify Date : 2017:08:11 03:39:44+00:00 Creator : AH XSL Formatter V6.3 MR3 for Windows (x64) : 6.3.4.25128 (2016/07/01 17:39JST) Producer : Antenna House PDF Output Library 6.3.815 (Windows (x64)) Keywords : Edge Gateway 3001-3002-3003, Edge Gateway 3000 Series-Getting Started, Edge Gateway.3000 Series-Setup, Edge Gateway 3000 Series-Installation, Edge Gateway 3000 Series-Operation, Connection, Antenna, Activate WWAN, Mount, Windows 10 IoT, Ubuntu Core 16, Access.BIOS, Flash BIOS, ZigBee, Boot OS, Restore OS Title : Dell Edge Gateway 3002 Installation and Operation Manual Subject : Service Manual Trapped : False Page Count : 77 Page Mode : UseOutlines Tagged PDF : Yes Language : ENEXIF Metadata provided by EXIF.tools