Dell Storage Sc460 Expansion Enclosure Getting Started Guide User Manual Setup En Us

User Manual: Dell storage-sc460 - Dell SC460 Expansion Enclosure Getting Started Guide

Open the PDF directly: View PDF PDF.
Page Count: 11

DownloadDell Storage-sc460 SC460 Expansion Enclosure Getting Started Guide User Manual  - Setup En-us
Open PDF In BrowserView PDF
Dell SC460 Expansion Enclosure
Getting Started Guide

Regulatory Model: CYAE

Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its
subsidiaries. Other trademarks may be trademarks of their respective owners.
2017 - 08
Rev. A01

Setting Up the Expansion Enclosure
Consider the following best practices when setting up an SC460 expansion enclosure.
•

Before connecting any cables between the expansion enclosure and storage system, physically label each port and connector.

•

Always follow proper power-up and power-down procedures when cycling power across the network. Verify that critical network
components are on separate power circuits.

Other Information You May Need
To install the expansion enclosure, you may need the following additional information:
•

Dell SC460 Expansion Enclosure Owner’s Manual
Provides information about an SC460 expansion enclosure, such as hardware features, replacing hardware components, and
technical specifications.

•

Dell Storage Manager Administrator’s Guide
Provides instructions for using the Data Collector Manager and the Dell Storage Manager Client.

Installation and Configuration
Before you begin the installation, make sure that the site where you plan to install the expansion enclosure has standard power from
an independent source or a rack power distribution unit (PDU) with a UPS.

Safety Precautions
Always follow these safety precautions to avoid injury and damage to Storage Center equipment.
If equipment described in this guide is used in a manner not specified by Dell, the protection provided by the equipment could be
impaired. For your safety and protection, observe the rules described in the following sections.
NOTE: See the safety and regulatory information that shipped with each Storage Center component. Warranty
information is included as a separate document.

Installation Safety Precautions
Follow these safety precautions when installing an SC460 expansion enclosure:
Caution
Equipment exceeds 90 kg (200 lb). Use appropriate lifting methods when installing an
SC460 expansion enclosure.

•

You can install the expansion enclosure chassis without using a mechanical lift if you remove the drives, cooling fans, power
supply units (PSUs), and enclosure management modules (EMMs) from the chassis before installing it.
You must use a mechanical lift to install the expansion enclosure chassis if you do not remove the drives, cooling fans, PSUs, and
EMMs from the chassis.

•

Dell recommends that only individuals with rack-mounting experience install an SC460 expansion enclosure in a rack.

•

When installing multiple expansion enclosures in a rack, fill the rack from the bottom up and empty the rack from the top down.

•

The rack construction must support the total weight of the installed expansion enclosures. The design should incorporate
stabilizing features suitable to prevent the rack from tipping or being pushed over during installation or in normal use.
3

•

To prevent the rack from tipping, slide only one expansion enclosure out of the rack at a time.

•

Make sure that the expansion enclosure is always fully grounded to prevent damage from electrostatic discharge.

•

When handling the expansion enclosure components, use an electrostatic wrist guard or a similar form of protection.

Unpacking Storage Center Equipment
Unpack the SC460 expansion enclosure and identify the items in your shipment.

Figure 1. SC460 Expansion Enclosure Components

1.

Expansion enclosure

2.

Rack rails (2)

3.

SAS cables (4)

4.

Power cables (4)

5.

Front bezel (Optional)

6.

Documentation

Determine the Mounting Location
Determine where to mount the SC460 expansion enclosure in the rack.
1.

Identify a location in the rack with 4U of space for the expansion enclosure.
WARNING: If you plan to install the expansion enclosure above the lower 20U of a rack, use a mechanical lift to
avoid injury.

2.

4

If you plan to install the 1U cable management tray below the expansion enclosure, identify a location in the rack with 5U of
space for the expansion enclosure and cable management tray.

Figure 2. Mounting Location from Front and Back of Rack

1.

Location for the clip nuts to secure the top cover

2.

Location for the clip nuts to secure the expansion
enclosure

3.

Location for the expansion enclosure rack rails

4.

Location for the 1U cable management tray rails

Mount the Cable Management Tray
If you plan to use the 1U cable management tray, mount the tray before mounting the SC460 expansion enclosure.
Prerequisite
Required materials:
•

Screwdriver (034-000-193)

•

Four 8-32 x 0.75 in. knurled head Phillips screws (036-034-012)

•

Left 1U cable management tray rail (042-034-012)

•

Right 1U cable management tray rail (042-034-008)

•

1U cable management tray (042-033-060)

Steps
1. Adjust the length of the 1U cable management tray rails (042-034-012 and 042-034-008) to fit the rack.
2.

Align the rails so that the UP arrow is pointed in the correct direction and the side of the rail labeled FRONT is at the front of
the rack.

3.

Insert the alignment pins of left and right rails into the mounting holes at the front and back of the rack.

4.

Secure the rails by installing 8-32 x 0.75 in. screws (036-034-012) into the holes at the front and back of the rails.

5

Figure 3. Secure Rails to Rack

5.

Align the 1U cable management tray (042-033-060) so that the UP arrow is pointed in the correct direction and the side of the
tray labeled FRONT is to the front of the rack.

Figure 4. Align the Cable Management Tray

6.

Slide the 1U cable management tray into the rails until it locks into place.

Mount the Expansion Enclosure
Install the rails in the rack, and mount the SC460 expansion enclosure on the rails.
Prerequisite
Required materials:
•

Screwdriver (034-000-193)

•

Six clip nuts (106-569-307)

•

Two M5 x 10 mm Phillips pan-head screws (106-002-452)

•

Two M5 x 16 mm Phillips pan-head screws (106-002-453)

•

Left and right expansion enclosure rack rails (100-569-001)

Steps
1. Adjust the length of the expansion enclosure rack rails (100-569-001) to fit the rack.
2.
6

Attach the right rail to the back post of the rack.

a. Align the right rail with the lower two U spaces of the 4U mounting location.
b. With the release latch on the outer part of the rack post, place the catch mechanism over the post.
c. Push the rail back to secure the rail to the rack post.
An audible click indicates that the rail is secure in the post.
d. Make sure the post/catch mechanism is secure and attached to the rack post.

Figure 5. Attach Rail to the Back of the Rack

3.

Attach the right rail to the front post of the rack.
a. Align the right rail with the lower two U spaces of the 4U mounting location.
b. Pull the rail forward, with the alignment pins in the middle holes of the bottom two U spaces of the 4U mounting location.
An audible click indicates that the rail is secure in the post.

Figure 6. Attach Rail to the Front of the Rack

4.

Secure the rail by installing an M5 x 10 mm screw (106-002-452) in the larger of the two holes at the front of the rail.

5.

Secure the rail by installing an M5 x 16 mm screw (106-002-453) in the larger of the two holes at the back of the rail.

6.

Repeat steps 2 through 5 to install the left rail.

7.

Mount the expansion enclosure chassis on the rails.
a. If a mechanical lift is available, use the four handles that shipped with the expansion enclosure to lift the expansion
enclosure chassis onto a mechanical lift.
b. If a mechanical lift is not available, remove the drives, cooling fans, power supply units (PSUs), and enclosure management
modules (EMMs) from the expansion enclosure chassis and use the four handles to lift the chassis to the mounting location.
c. From the front of the rack, extend the rack rails approximately 5 to 8 cm (2 to 3 in.) and align the expansion enclosure
chassis rails with the rack rails.

7

Figure 7. Extend the Rack Rails

d. Slide the rack rails over the expansion enclosure chassis rails.
e. Remove the four handles from the sides of the expansion enclosure chassis.
f. Slide the expansion enclosure chassis into the rack.

Figure 8. Mount the Expansion Enclosure into the Rack

8.

If the drives, fans, PSUs, and EMMs were removed from the expansion enclosure chassis, reinstall these components in the
chassis.

9.

Secure the expansion enclosure chassis and top cover.
a. Install the six clip nuts (106-569-307) into the rack holes that align with the shoulder screws on the front of the expansion
enclosure chassis.
b. Use the orange enclosure latch handles to push the expansion enclosure chassis completely into the rack.
Make sure that the self-locking latches are pushed in and fully engaged to prevent the expansion enclosure chassis from
sliding out of the rack.

8

c. Secure the expansion enclosure chassis to the rack using the orange shoulder screws.
d. If the top cover is secured by two small shipping screws, remove the screws.
e. Secure the top cover of the expansion enclosure chassis to the rack using the shoulder screws.

Install the Front Bezel
If a front bezel is shipped with the SC460 expansion enclosure, install the bezel on the front of the expansion enclosure.
1.

Align the bezel with the front of the expansion enclosure.

2.

Press the two latches on front of bezel.

Figure 9. Install the Bezel

3.

Push the bezel into place until it attaches to the expansion enclosure.

4.

Release the latches on the front on the bezel.

5.

If the bezel has key lock, lock the bezel with the key.

NOM Information (Mexico Only)
The following information is provided on the device described in this document in compliance with the requirements of the official
Mexican standards (NOM):
Importer

Dell Inc. de México, S.A. de C.V
Paseo de la Reforma 2620-11 ° Piso
Col. Lomas Atlas
11950 México, D.F.

Model number

CYAE

Supply voltage

200–240 VAC

Input frequency

50/60 Hz

Input current

2.25A x2 (N+1)

9

Technical Specifications
The technical specifications of the SC460 expansion enclosure are displayed in the following tables.
Drives
SAS hard drives

Dell Enterprise Plus drives
Up to 60 hot-swappable 7.2K RPM 12 Gbps 3.5” SAS hard drives

Connectivity
Configurations

SC9000, SC7020, and SC5020 storage systems support up to three SC460 expansion enclosures

Enclosure Management Modules (EMMs)
EMMs

Two hot-swappable EMMs with four 12 Gb SAS ports per EMM. The expansion enclosure
supports Mini-SAS HD cables in lengths of 3 m, 4 m, and 5 m.

SAS connectors

SAS connectors are SFF-8644 compliant

AC Power
Power supply wattage

1600 W per power supply

AC line voltage

200 to 240 VAC ± 10%, single-phase, 47 to 63 Hz

AC line current (operating
maximum)

4.9 A max at 200 Vac

Power consumption (operating 980 VA (931 W) max
maximum)
Power factor

0.95 min at full load, low voltage

Heat dissipation (operating
maximum)

3.36 x 106 J/hr, (3177 Btu/hr) max

Physical
Height (4U chassis)

17.5 cm (6.89 in.)

Height (4U chassis plus 1U cable management tray)

22.23 cm (8.75 in.)

Width (including rails)

44.45 cm (17.50 in.)

Depth (chassis only)

87.63 cm (34.5 in.)

Maximum depth (fully configured)

92.46 cm (36.4 in.)

Weight (maximum configuration)

102.05 kg (225.0 lb)

Environmental
Temperature
Operating

5° to 40°C (41° to 104°F) with a maximum temperature gradation of 10°C per hour

Storage

-40° to 65°C (-40° to 149°F) with a maximum temperature gradation of 25°C per hour

Relative humidity
Operating

10

20% to 80% (noncondensing)

Environmental
Storage

10% to 90% (noncondensing)

Altitude
Operating

-16 to 2300 m (-50 to 7500 ft)

Storage

-16 to 10,600 m (-50 to 35,000 ft)

11



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Dell
Create Date                     : 2017:10:02 20:36:25+00:00
Modify Date                     : 2017:10:02 20:36:25+00:00
Creator                         : AH XSL Formatter V6.3 MR3 for Windows (x64) : 6.3.4.25128 (2016/07/01 17:39JST)
Producer                        : Antenna House PDF Output Library 6.3.815 (Windows (x64))
Keywords                        : guide, Dell, expansion, enclosure, SC460, SC9000, SC7020, SC5020, getting started, setting up, mounting, rails, safety
Title                           : Dell SC460 Expansion Enclosure Getting Started Guide
Subject                         : Setup Guide
Trapped                         : False
Page Count                      : 11
Page Mode                       : UseOutlines
Tagged PDF                      : Yes
Language                        : EN
EXIF Metadata provided by EXIF.tools

Navigation menu