| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 57453 |
| Application ID | c63220CRx5tVkFjwU1GOvw== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 144.17kB (1802070 bits) |
| Date Submitted | 1999-08-31 00:00:00 |
| Date Available | 1999-10-14 00:00:00 |
| Creation Date | 2001-06-05 01:58:02 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-06-05 01:58:48 |
| Document Title | 57453.pdf |
| Document Author: | VicodinES /CB /TNN |
A hELTd
Delta Electronics., Inc.
NOTEBOOK COMPUTER
DN-615
User’s Manual
TABLE OF CONTENTS
CHAPTER 1: INTRODUCING YOUR NOTEBOOK
INTRODUCTION
DISCOVERING THE UNIT
RIGHT-SIDE COMPONENT
LEFT-SIDE COMPONENTS .
REAR-SIDE CONNECTORS.
COMPONENTS ON THE BASE
HARD DISK DRIVE AND SYSTEM MEMOR
CHAPTER 2: USING THE NOTEBOOK FOR THE FIRST TIME
ABOUT THE KEVBOARD....... ..
USING THE TOUCHPAD
CONNECTING POWER TO THE SYSTEM
FIRST TIME START UP ..
USING THE DRIVES
CHAPTER 3: CONFIGURING THE NOTEBOOK
SYSTEM CONFIGURATION UTILITY
START!)
MEMORY .
DISKS
COMPO
POWER.
EXIT
CHAPTER 4: TAKING YOUR NOTEBOOK ON THE ROAD
BATTERY AND POWER SAVING
POWER MANAGEMEN
MODEM..................
SAFETY AND OPERATIO
TRAVEL TIPS .
USING A COMPUTER OCK .
CHAPTER 5: EXPLORING YOUR NOTEBOOK
INTRODUCTION . 1
VIDEO DISPLAY. I
THE SOUND SYSTE 5
USING THE CD-ROM/DVD DRIVE. 8
USING THE mew DISK. 5-10
PC CARD SLUI‘S ........ 5-10
TOUCI-IPAD/MOUSE UTILlTY 5-13
INFRARED ..........................
CHAPTER 6: EXPANDING YOUR NOTEBOOK
UPGRADING AND OPTIONS
APPENDIX A: NOTEBOOK SPECIFICATIONS
SPECIFICATIONS.
APPENDIX B: DEVICE DRIVER INSTALLATION
INTRODUCTION .........................
DRIVER INSTALLATION PROGRA
Copyright
The information in this guide is subject to change without prior notice.
Manufacturer shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the furnishing,
performance, or use of this material.
This manual contains information protected by copyright. No part of this manual may
he photocopied or reproduced in any form without prior written consent from
manufacturer.
© 1999 All rights reserved.
The sofiware described in this guide is furnished under a license agreement or
nondisclosure agreement. The software may be used or copied only in accordance with
the terms of the agreement.
Product names mentioned herein may be trademarks and/or registered trademarks or
their respective companies.
First Edition July 1999
Produced by Immediate Media Services 7 Taipei
www.imn1ediate.com,tw
Battery Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer,
Keep the battery away from fire. Do not dispose in fire.
Do not expose the battery pack to direct sunlighL
Contact local environmental agencies for information on recycling and disposal
plans in your area. Discard used batteries according to the manufacturer‘s
instructions.
Do not directly connect (short circuit) the positive (+) and the negative (-)
terminals. Never attempt to disassemble the battery pack.
Do not use a battery charger or AC adapter other than the designated one provided
with your notebook to charge the battery pack.
Follow these guidelines in order to prevent damage to the notebook, and/or harm to
the user. Mishandling the battery may cause it to explode.
Introduction
Device drivers are software files that allow pieces of hardware to
communicate effectively with the notebook and the operating system. All such
specific drivers necessary have been preloaded for the various hardware units
that have been packaged with your system.
All the device drivers needed for your syswm are also available on the support
CD that shipped with your notebook.
The support CD contains drivers for:
- 3Mode ~ Japanese floppy disk drivers and utilities (In order to support 12
MB format floppy disks, a format popular in Japan, you need to install this
mode 3 floppy disk driver software.)
- Audio — sofiware support for audio
- CD—ROM — sottware support for CD-ROM drive
' PCMCIA — software support for PC—card drive
. Modem — sofiware support for internal modem device
- VGA » sofiware support for display
The support CD also holds a copy of the online manual for your notebook.
This is an online version of this user’s manual.
NOTE: If you encounter any problems using the online user's manual you can
install the HTML Help Update program (update.exe), also available on the
support CD This will update your computer for optimal use of the user's
manual.
Driver Installation Program
If you ever need to reinstall the device drivers (ego after hard disk failure,. . .),
you can use the driver installation program on the support CD which will
automatically install all the necessary drivers for you.
To access the device driver installation program:
Place the support CD in the CD-ROM drive.
2. If the installation program fails to start after 20 seconds, click on the Start
menu, select RUN, and type:
Dzmetupexe
B—l
(Where D represents the CD-ROM drive)
3. A window screen will pop up, with a menu bar on the lefi.
4. Click the check boxes of the drivers you want to install, then click [Select
Install]. This will install all the drivers you previously marked. You can
also install individual drivers by clicking the button area of a menu item.
This will only install that particular driver.
5. After you click the button, the installation program for that particular
driver will start and might prompt you for some input. Follow the screen
instructions to finish the installation.
6. If you need to restart the system, retum afierwards back to the installation
program to finish all the other installations you need to make.
7. For more help on the installation program, review the manual file linked to
the [Manual] button.
Chagter 1
Introducing your Notebook
This chapter provides a
brief description of all
the major components
of your notebook
Introduction
Congramlan’ons on your purchase of this powerful notebook computer, This
high-end system runs the latest generation of Intel Celeron processors that are
designed to deliver smooth multimedia and lighting-fast performance. The
system is equipped with built-in audio and a large bright built-in screen.
The unit is equipped Willi an internal built-in set of drives. The system also
boasm a full set of expansion parts so that you can create an extended
computing environment that challenges the best full-sized desktop systems for
performance.
Figure 1-1: Your Notebook
1-l
Opening the Notebook
The screen cover is locked down by a latch on the front edge of the notebook.
Slide the latch to the right to unlatch the screen and open the screen cover.
Figure 1-1: Opening the Cover
Discovering the Unit
When the screen cover is opened, the main working area of the notebook is
visible. This area includes the built-in screen, the keyboard, and the touchpad.
Screen Latch l_\
Built-in Screen
Power Switch
Status Indicalors
anume Buttons
Microphone Keyboard
Battery
Cooling Vent
Speaker
Tonehpad
Speaker Power Indicators
Figure 1-1: Working Are-
1»2
Built-in Screen
This notebook can be installed with color LCDs (Liquid Crystal Displays).
The LCD measures 14.1” diagonally. Screen use a TFT active matrix display
that delivers a bright, high—contrast picture. The screen resolutions are XGA
(1024 x 768). XGA resolution puts the maximum infonmtion on the display,
without making the text and icons too small to be legible.
Power Switch
The power switch is located just above the keyboard in the middle, and is used
to turn the notebook on and off. Press the switch down and hold it down until
you see the indicator LEDs flash. Hold the switch down again for over 4
seconds to tum the system off.
Volume Buttons
The volume buttons are located just above
the keyboard, next to the power switch.
Pressing the top button increases the
volume of the internal sound system,
pressing the lower button decreases the
volume level.
Figure 1-1: Volume buttons
Cover-close I Suspend-resume Micro Switch
The cover-close micro switch is pressed whenever the screen cover has been
closed. When this happens, the system will either turn off the built—in screen or
suspend the system, The response is defined by the system setup utility (See
chapter 4 for information on the cover close response.)
Microphone and Speakers
Your notebook has a built-in stereo audio system. The speakers are located in
the front side of the notebook. The microphone is located below the LCD in
the cover of the notebook.
Status Indicators
The status indicators are located above the keyboard. When the system is
turned on, the indicator LEDs show the status of the system and the major
components.
The green LED next in this icon tums on when the notebook is
powered on. When the system is suspended to RAM, the LED
flashes. When the system is suspended to disk, or when the
system is powered down, the LED turns off.
The LED next to this icon tums on green when the battery inside
the notebook is fully charged. When the battery is charging the
LED tums amber. When there is less than 3 minutes of battery
capacity left, the LED turns red and flashes, while an audible
warning beep sounds.
Built-in Keyboard
Most versions of the built-in keyboard use 86 keys. Some non-english
keyboards may have one or two extra keys. Some keys are embedded with
several keystrokes so that the keyboard can duplicate all the keystrokes of a
standard desktop AT or PS/Z keyboard with 101/102 keys. The keyboard is
optimized for Windows and has two kinds of special Windows keys. On top of
these standard desktop keyboard functions, the notebook keyboard also has hot
keys to give the user direct access to a series of oflen used functions (See
chapter 2 for more information on the keyboard.)
Touchpad
The touchpad is your notebook’s pointing device. In a graphical environment
like Windows, the touchpad surface acts like a representation of the built-in
screen. When you move your fingertip over the touchpad surface, the pointer
on the screen moves in the same direction. (See chapter 2 for more information
on the touchpad.)
1—5
(9
E?
E]
®BE®
Figure 1-1: Status lndientors
The green LED next to this icon turns on when the notebook is
reading from a disc in the CD-ROM or DVD drive.
The green LED next to this icon toms on when the notebook is
reading from or writing to the built-in hard disk drive.
The green LED next to this icon turns on when the notebook is
reading from or writing to a diskette in the floppy disk drive
The green LED next to this icon turns on when the keyboard is in
Num Lock mode.
The green LED next to this icon turns on when the keyboard is in
Caps Lock mode.
The green LED next to this icon trims on when the keyboard Is In
Scroll Lock mode.
Power Indlcators
The power indicators are located on the front edge of the notebook, below the
buttons of the touchpnd. When the system is turned on, these indicator LEDs
show the power and charging status of the system and internal battery. The
power indicator LEDs are visible at all time, even when the notebook cover is
closed.
14
QC)
Flgure 1-1: Power lndluten
The green LED next to this icon tums on when the notebook is
using power from the AC adapter.
Right-side Components
The right side of the notebook is the location of the CD—ROM/DVD drive, the
infrared port, The AC adapter plug and also the anchor for the security locking
cable.
Lock Anchor
AC Adapter Jack
CD-ROM Drive
Figure 1—1: Right-side Components
CD-ROM Drive
This drive bay is installed with a CD-ROM drive. This option is factory
installed and can not be easily switched. You can use this drive to read fi-om
CD data discs, video discs, and audio discs.
Ac Adapter Jack
You can plug the DC power cable into the AC adapter in order to power your
notebook from the AC adapter.
Infrared Port
The infrared (IR) port allows you to connect to another system using [R
technology. You must place the port within four feet (1 m) and a 30° angle of
the other IR port for proper communication.
Lock Anchor
The lock anchor is a rectangular hole on the right side of the back edge of the
notebook. You can use this hole to attach a secln'ity locking cable (such as a
Kensington MicroSaver) to your notebook.
1-6
Left-side Components
The left side of the notebook is the location of the PS/Z connector, the PC card
slot compartment, and also the floppy disk/LS-IZO drive.
PS/2 Port Floppy Disk Drive
Cooling Vent L/
PSIZ Felt
You can use the mini—DIN PS/2 port to connect your computer to an external
PS/Z device, such as a keyboard or a pointing device, When you connect an
external keyboard or mouse, the internal equivalent remains active.
PC Card Slot Compartment
Figure 1-1: Left-aide Component!
PC Card Slots
The PC card compartment reveals two PC card slots. These slots accept Type I,
II, or HI PC cards, as well as loomed Video, CardBus, and 13ch compatible
PC cards. Eject buttons for both slots are placed at the lefi side of the slots.
Floppy Disk Drive
This drive bay is installed with a floppy disk drive. This option is factory
installed and can not be easily switched The floppy disk drive can be used to
read from and write to 3.5” floppy disks with capacities of 720 K or 1.4 MB.
Your notebook identifies the floppy disk drive as drive A.
Rear-side Connectors
The rear side of the notebook has a series of connectors. Some of these
connectors are located inside a separate compartment. Each compartment has a
pull-down door to protect the ports inside the compartments. The illustration
and list below identifies the fimction of each of the connectors.
Figure 1-1: Connector Compartments
To access the covered compartments, pull down the doors. The door of the
expansion connector compartment flaps away underneath the notebook.
Fax/Modem
The fax/modem line-in jack provides the connection for the internal
fax/modem device. If your notebook did not come with this factory installed
option, the access to this jack will be blocked with a cap. The jack does not
prov1de a pass-through option for connecting a phone to this same line.
Audio Janice
Audio Input Jack /_I Audio Output
You can use this jack
to input stereo sound 0
from other devices,
such as a radio or
tape recorder, into fl
your notebook
13?
\_l Audio Input
External Micro hone
F V Figure 1-1: Audio Juli:
External Microphone Jack
You can use this jack to input sound from an external microphone into your
notebook. When an external microphone is connected to this jack, the built-in
microphone is automatically disabled.
1-8
Audio Output Jack
You can use this jack to output sound generated by your notebook to an
external device, such as stereo loudspeakas or headphones. When an external
device is connected, the built—in speakers are automatically disabled.
USB Port
The USB (Universal Serial Bus) port can be used to connect to USB devices.
Monitor Fort
The monitor port can be used to connect to an external monitor.
Serial Port
The serial port COMl can be used to connect to serial devices such as a mouse
or a fax/modem.
Parallel Polt
The parallel port LPTl can be used to connect to parallel devices such as a
printer.
TV-out Port
The RCA video jack can be used to output video to devices that use RCA
plugs such as most TV receivers.
Components on the Base
If you close the screen cover and turn the unit over, you can locate the
components installed on the base of the unit.
Foot BIOS CMOS
Compamnent
Memory
Compartment
Figure 1-1: Bale Component:
Battery
The notebook contains a removable, rechargeable Lithium ion (Li-Ion) battery
pack that provides power when you are away from an AC outlet. You can
recharge it many times.
Ergonomic Feet
There are two feet located at the back of the base of the notebook. Opening
these feet allows the notebook to slightly tilt forward towards you, to make the
keyboard more easily accessible.
BIOS CMOS Comparlment
This compartment gives access to the BIOS chip that holds the System
Configuration Utility infonnation. We recommend not to open the
compam-nent, and never to remove the chip from the notebook.
1—10
Hard Disk Drive and System Memory
Exploring your notebook because they are internal items, installed inside the
system case can’t identify these two items. However, they are vay important
components that store the software and data that your computer uses.
System Memory
The notebook is usually installed with 32 megabytes (MB) of system memory.
This is plenty of memory for most kind of computer applications. However, if
you feel that you need more memory, you can ask your system vendor to
upgrade the memory. The notebook can be installed with a maximum of 256
MB. System memory stores applications and data while the system is turned
on. When the system is turned off, all the data stored in system memory is lost.
Hard Disk Drive
The notebook is installed with a hard disk drive, which can store from 3 to 6 or
more gigabytes (GB) of sofiware and data. Over time, new hard disk drives
with higher capacities will appear, so if you feel that you need more hard disk
space, you can ask your vendor about upgrades. The hard disk drive provides
long-term storage, because the sofiware and data is held intact even when the
computer is tumed off. That's why, before you turn off your computer, you
must always make sure that the data or files held in the system memory, are
securely saved to disk.
1-11
Chagter 2
Using the Notebook for the
First Time
This chapter explains
the procedures that you
should follow tho first
time that you use the
notebook
About the Keyboard
If you are not familiar with notebook computers, you should read this section
which describes the layout of the notebook keyboard.
Keyboard Layout
The appearance of the notebook keyboard depends on the version of the
system that you are using, and the language version of your system For some
languages, one or two extra keys are required, and extra keystrokes may be
embedded into the keys. The illustration below shows a picture of a typical
keyboard.
FImeIinnKeys R NunurieKeybnlrd
muuuummsmgluuuuuu
IllIJlIJluJULElLJlIJ LFSMIIJLEJHEJLI
Eumwunmmummulul ULIJ
gluuuuuiu LJLJLJIEJLJLJ
MMLJHIIIJH unmwuuqm
EliuuulfilUILJLl-le
l—
EJIEJLEJ
\_l Cllnar Keys
Flgure 2-1: Sand-rd Keyboard Llymlt
Fu key
Key Legends
In the upper lefi comer, each keycap carries a large legend of the normal
keystroke. If there are two legends, the upper keystroke 18 selected by holding
down the Shift key.
Embedded Keypad
The alphabet keys on the right side have an embedded numeric keypad that
can be turned on by pressing the Nun-1 Lock key The embedded keypad
legends are usually positioned 11-1 the upper right comer of the keycaps (in
some language versions, the keypad legends may be positioned on the front
edge of the keyeap).
Function Keys
The function keys from the top row of the keyboard. The action of the fiinction
keys is usually determined by the sofiware that the computer is running. Some
of the function keys have a second action embedded. This action is identified
as an icon on the keycap, This action is selected by holding down the Fn
Function key (in the lower lefi comer of the keyboard) while pressing the
function key,
Function Key Reference
The table below shows the meaning of the fimction key icons, and other
embedded keyboard icons:
Keystrokes Icon Milan
Fn 0 F2 = This key combination causes your notebook to
switch to Suspend mode. (See chapterA, tor
,/‘\ information on the Suspend mode option on your
’ ‘ notebook)
PM + F3 This key combination toggles the video display on
LCD/CRTILCD+CRT
FN + F5 This key combination toggles the video display on
the built-in screen on and oil.
FN 4, F7 This key combination Increases the brightness of
T the built-in screen.
PM + F8 This key combination decreases the brightness of
i the b in screen.
Windows Keys
The Windows keys are located on either side of the Space bar. They are active
in Windows 95, Windows 98, or Windows NT,
a This key activates the Start button Windows Task Bar.
object. Its action is the same as right-clicking an loan or object
ER This key opens the pull down menu of a selected icon or
with a mouse or touchped.
2-2
Using the Touchpad
If you are unfamiliar with notebook computers, you should read this section
which explains how to use the touchpad-pointing device. Moving your
fingertip across the touchpad surface, is exactly the same as moving a mouse
across a mousepad. The screen pointer (in graphical environments such as
Windows) moves in response to the movements on the touchpad.
Figure 2-1: Using the Touchpad
Touchpad Buttons
Two buttons are located below the touchpad. The button on the lefi acts
exactly like the Iefi button on a mouse. You can click it once to select an icon,
object or file, and click or double-click to execute an action on a selected icon,
object, or file.
The button on the right acts exactly like the right button on a mouse. In the
Windows environment, a right click usually displays a pull-down properties
menu for whatever icon, object, or file is selected
Tapping the Touchpad Surface
You can operate most of the touchpad functions with a single fingertip. When
you need to execute a lefl button mouse click, tap gently on the touchpad
surface with your fingertip. Tap twice quite rapidly to execute a double-click.
For drag and drop operations, tap twice, but keep your fingertip in contact with
2-3
the touchpad surface afler the second tap, you can then drag objects around the
screen. When your fingertip breaks contact with the touchpad surface, the
object is dropped.
Connecting Power to the System
Your notebook can operate through the AC adapter connected to a wall outlet,
or it can operate from the removable, rechargeable battery installed in the lefi
side of the unit.
When you are using your notebook for the first time, it is essential that you use
the AC adapter connected to a suitable power supply. The battery in a newly
purchased system is usually fiilly discharged or has just a little charge
remaining. When you first use the notebook, you must have sufficient power
to complete the Windows initialization process without ninning out of power.
The AC adapter is autosensing so it can use any available power supply fi'om
100 volts through to 240 volts (i l0%VAC) with a frequency ranging from 50
to 60 Hertz. The AC adapter is also used to recharge the rechargeable battery.
Direct Current Cable I.\
Power Indicator Light
——3=
\_1 AC Power Cord
Flgure 1-1: AC Adapter
AC Adapter |_/ i
1. Plug the power cord mm a regular AC power supply outlet.
2. The power indicator light on the AC adapter will turn on to show that it is
connected to AC power.
3. Plug the direct current cable fi'om the AC adapter into the AC adapter jack
on the lefi side of the notebook.
/_| To AC Adapter Jack
-——G=')
\_l To Wall (min
Figure 2-2: Connecting the AC Adapter
44 The left side power indicator on the front edge of the notebook will turn
on with a green light. At the same time the right power indicator will turn
on or flash to indicate internal battery statusl
First Time Start Up
When you have connected the notebook to a suitable power supply, and you
are familiar with the operation of the keyboard and touchpad, you are ready to
begin using your computer.
NOTE: It is particularly important that you give your battery 8 full
charge the first time that you use it. We recommend that you leave the
system connected to the AC adapter until the battery is fully charged.
The right power indicator lamp on the front edge of the notebook will
turn green when the internal notebook battery is fully charged.
The Windows operating system is partially installed on your system. The
installation is completed when you turn on the computer for the first time At
that point, Windows will run a setup program which gathers important
information about you and your computer preferences, so that Windows
operates the way you want it to.
Throughout the setup procedure, Windows will present dialog boxes on the
screen. When you have read the dialog box and wish to proceed with the
installation, use the touchpad to point to the Next button and then click it. If
you wish to review a part of the installation procedure, click on the Back
button.
2-5
1. Turn on your notebook by pressing the power switch down and holding it
down for about two seconds When you see activity on the power and
status indicator panels, you can release the power switch.
2. When Windows starts, you may see a Safe Recovery message. This means
that the notebook has been turned on at least once since the partial
installation of Windows, and Windows has registered the fact that the final
installation was not completed at that time. You can ignore the safe
recovery message and proceed.
3. The setup program will ask for the language and layout of your keyboard.
Select the appropriate items from the list provided and proceed.
4. Setup will then ask for your name and company name if applicable. Type
in the information and proceed.
5 Setup will then display the Windows license agreement. This document
details the terms and condition under which you are licensed to use the
Windows sofiware. You must read this information and then click on the
“I accept the agreement” check box in order to proceed.
6. Setup will then ask you to type in the registration number on the
Certificate of Authenticity (COA). The COA is generally pasted on the
front cover of the Windows manual that is shipped with this system.
7. Setup will then begin to configure your computer. After some time, you
will be required to restart the computer.
8. When the notebook has restarted, setup will ask you to select a printer for
your system. You can select a printer at this time, or leave it till later if
you prefer.
9. Setup will then display a Time Zone window. Use the touchpad to select
the correct time zone for you location, and reset the time and date.
That completes the Windows setup program Your notebook is now installed
with your own personal copy of Windows.
Using the Drives
You can learn a lot about your computer by using the windows My Computer
utility. If you click on this icon, it will show a graphical representation of the
media devices on your system. Depending on the configuration of your system,
your notebook will probably have the following devices:
2-6
Hard Disk Drive
The hard disk drive is an internal component and is identified by your system
as drive C:. The Windows operating system is stored on the hard disk drive,
and when you install new sofiware applications on your system, they will
usually be stored on the hard disk drive. The hard disk drive provides very fast
access to your data and applications.
Floppy Dlsk Drive
The drive bay on the left side of the notebook is installed with a floppy disk
drive. This option is factory installed and can not be easily switched. Drive use
removable 3.5" diskettes. The floppy disk drive uses low capacity (1.44 MB)
diskettes. Your system identifies this disk drive as drive A:. Access to the
floppy disk drive is quite slow but floppy diskettes are very useful for storing
and transferring files
CD-ROM Drlve
The drive bay on the right hand side is installed with a CD-ROM drive, This
option is factory installed and can not be easily switched CD-ROM disks can
store over 600 MB of audio, video, or data. Usually your system identifies the
CD-ROM drive as drive D: . Access to a CD-ROM is quite fast. CD disks are
used to distribute large sofiware applications, and audio and video files that
require a lot of capacity. You can play audio and video files using the
Windows media player.
2-7
2-8
Figun m: CD-ROM Drive my
Chagter 3
Configuring the Notebook
This chapter provides
an overview of the
System Configuration
Utility program, which
allows you to adjust the
basic notebook settings
to your needs
System Configuration Utility
The System Configuration Utility lets you use the firmware installed on the
notebook to configure your system according to the kind of hardware that you
install. Using setup, you can set timing parameters for the memory and
processor, define drive specifications, control power management, and so on.
Using the System Conflguratlon UtIIity
You can only display the setup utility by pressing the [Ctrl] + [Alt] + [5] key
combination shortly afier the system is turned on. A prompt appears on the
screen that reads " ta enta‘ System Configuration Utility
When you see this prompt, press the key combination and the setup utility will
display the main page of the System Configuration Utility program.
Syn-n
CPUClock - 400 Mhz
mwmmmivmmmmammnymmip.mm
mummmdzmpkmmmwmmmumm
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.3
Linearized : Yes
Create Date : 2001:06:05 01:58:02
Producer : Acrobat Distiller 4.0 for Windows
Author : VicodinES /CB /TNN
Title : 57453.pdf
Modify Date : 2001:06:05 01:58:48-04:00
Page Count : 87
EXIF Metadata provided by EXIF.tools