Delta Electronics F5D72304 Wireless G Router User Manual P74688 F5D7230 4 1223 indd

Download:
Mirror Download [FCC.gov]
Document ID	508003
Application ID	tgzB9cyGX1pmlLwq/uw1yg==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	234.44kB (2930471 bits)
Date Submitted	2005-01-20 00:00:00
Date Available	2005-01-20 00:00:00
Creation Date	2005-01-18 09:50:33
Producing Software	Adobe PDF Library 6.0
Document Lastmod	2005-01-18 09:50:59
Document Title	P74688_F5D7230-4-1223.indd
Document Creator	Adobe InDesign CS (3.0)

Alternate Setup Method
(10)
(2)
(5)
(4)
(3)
(6)
(1)
(7)
(8)
(9)
2.
Home Button
The home button is available in every page of the UI. Pressing
this button will take you back to the home page.
3.
Internet Status Indicator
This indicator is visible in all pages of the Router, indicating
the connection status of the Router. When the indicator says
“connection OK” in GREEN, the Router is connected to the
Internet. When the Router is not connected to the Internet, the
indicator will read “no connection” in RED. The indicator is
automatically updated when you make changes to the settings of
the Router.
4.
Login/Logout Button
This button enables you to log in and out of the Router with the
press of one button. When you are logged into the Router, this
button will change to read “Logout”. Logging into the Router will
take you to a separate login page where you will need to enter a
password. When you are logged in to the Router, you can make
changes to the settings. When you are finished making changes,
you can log out of the Router by clicking the “Logout” button. For
more information about logging into the Router, see the section
called “Logging into the Router”.
26
Alternate Setup Method
5.
6.
Help Button
The “Help” button gives you access to the Router’s help pages.
Help is also available on many pages by clicking “more info” next
to certain sections of each page.
LAN Settings
7.
Features
Shows the status of the Router’s NAT, firewall, and wireless
features. Changes can be made to the settings by clicking on any
one of the links or by clicking the “Quick Navigation” links on the
left side of the screen.
8.
Internet Settings
Shows the settings of the Internet/WAN side of the Router that
connects to the Internet. Changes to any of these settings can
be made by clicking on the links or by clicking on the “Internet/
WAN” Quick Navigation link on the left side of the screen.
9.
Version Info
Shows the firmware version, boot-code version, hardware
version, and serial number of the Router.
10. Page Name
The page you are on can be identified by this name. This manual
will sometimes refer to pages by name. For instance “LAN > LAN
Settings” refers to the “LAN Settings” page.
27
10
11
section
Shows you the settings of the Local Area Network (LAN) side of
the Router. Changes can be made to the settings by clicking on
any one of the links (IP Address, Subnet Mask, DHCP Server) or
by clicking the “LAN” Quick Navigation link on the left side of
the screen.
Alternate Setup Method
Step 4
Configuring your Router for Connection to your Internet
Service Provider (ISP)
The “Internet/WAN” tab is where you will set up your Router to
connect to your Internet Service Provider (ISP). The Router is capable
of connecting to virtually any ISP’s system provided you have
correctly configured the Router’s settings for your ISP’s connection
type. Your ISP connection settings are provided to you by your ISP.
To configure the Router with the settings that your ISP gave you,
click “Connection Type” (A) on the left side of the screen. Select
the connection type you use. If your ISP gave you DNS settings,
clicking “DNS” (B) allows you to enter DNS address entries for ISPs
that require specific settings. Clicking “MAC address” (C) will let you
clone your computer’s MAC address or type in a specific WAN MAC
address, if required by your ISP. When you have finished making
settings, the “Internet Status” indicator will read “connection OK” if
your Router is set up properly.
(A)
(B)
(C)
28
Alternate Setup Method
Setting your Connection Type
From the connection type page, you can select the type of connection you
use. Select the type of connection you use by clicking the button (1) next
to your connection type and then clicking “Next” (2).
(2)
10
11
29
section
(1)
Alternate Setup Method
Setting your Internet Service Provider (ISP) Connection Type
to Dynamic IP
A dynamic connection type is the most common connection type
found with cable modems. Setting the connection type to “dynamic”
in many cases is enough to complete the connection to your ISP.
Some dynamic connection types may require a host name. You can
enter your host name in the space provided if you were assigned one.
Your host name is assigned by your ISP. Some dynamic connections
may require that you clone the MAC address of the PC that was
originally connected to the modem.
(1)
(2)
(3)
1.
Host Name
This space is provided to enter a host name that needs to be
visible to your ISP. Enter your host name here and click “Apply
Changes” (3). If your ISP did not assign you a host name, or you
are not sure, leave this blank.
2.
Change WAN MAC Address
If your ISP requires a specific MAC address to connect to the
service, you can enter a specific MAC address or clone the
current computer’s MAC address through this link.
30
Alternate Setup Method
Setting your Internet Service Provider (ISP) Connection Type
to Static IP
(1)
(2)
(3)
(4)
(5)
10
11
1.
IP Address
Provided by your ISP. Enter your IP address here.
2.
Subnet Mask
Provided by your ISP. Enter your subnet mask here.
3.
ISP Gateway Address
Provided by your ISP. Enter the ISP gateway address here.
4.
My ISP Provides More Than One Static IP Address
If your ISP assigns you more than one static IP address, your
Router is capable of handling up to five static WAN IP addresses.
Select “My ISP provides more than one static IP address” and
enter your additional addresses.
31
section
A static IP address connection type is less common than other connection
types. If your ISP uses static IP addressing, you will need your IP address,
subnet mask, and ISP gateway address. This information is available from
your ISP or on the paperwork that your ISP left with you. Type in your
information, then click “Apply Changes” (5). After you apply the changes,
the Internet Status indicator will read “connection OK” if your Router is set
up properly.
Alternate Setup Method
Setting your ISP connection type to PPPoE
Most DSL providers use PPPoE as the connection type. If you use a
DSL modem to connect to the Internet, your ISP may use PPPoE to
log you into the service. If you have an Internet connection in your
home or small office that doesn’t require a modem, you may also
use PPPoE.
(1)
(2)
(3)
(6)
(4)
(5)
Your connection type is PPPoE if:
1) Your ISP gave you a user name and password which is required to
connect to the Internet
2) Your ISP gave you software such as WinPOET or Enternet300 that
you use to connect to the Internet
3) You have to double-click on a desktop Icon other than your
browser to get on the Internet
32
Alternate Setup Method
1.
User Name
This space is provided to type in your User name that was
assigned by your ISP.
2.
3.
Password
Type in your password and re-type it into the “Retype Password”
box to confirm it.
Service Name
MTU
The MTU setting should never be changed unless your ISP gives
you a specific MTU setting. Making changes to the MTU setting
can cause problems with your Internet connection including
disconnection from the Internet, slow Internet access and
problems with Internet applications working properly.
5.
Disconnect after X...
The Disconnect feature is used to automatically disconnect the
router from your ISP when there is no activity for a specified
period of time. For instance, placing a checkmark next to this
option and entering 5 into the minute field will cause the router
to disconnect from the Internet after 5 minutes of no Internet
activity. This option should be used if you pay for your Internet
service by the minute.
10
11
33
section
A Service name is rarely required by an ISP. If you are not sure if
your ISP requires a service name, leave this blank.
4.
Alternate Setup Method
Setting your Internet Service Provider (ISP) Connection Type to
Point-to-Point Tunneling Protocol (PPTP)
[European Countries Only]. Some ISPs require a connection using
PPTP protocol, a type of connection most common in European
countries. This sets up a direct connection to the ISP’s system. Type
in the information provided by your ISP in the space provided. When
you have finished, click “Apply Changes” (9). After you apply the
changes, the Internet Status indicator will read “connection OK” if
your Router is set up properly.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
1.
PPTP Account
2.
PPTP Password
Provided by your ISP. Enter your PPTP account name here.
Type in your password and retype it into the “Retype Password”
box to confirm it.
3.
Host Name
Provided by your ISP. Enter your host name here.
34
Alternate Setup Method
4.
Service IP Address
Provided by your ISP. Enter your service IP address here.
5.
My IP Address
Provided by your ISP. Enter the IP address here.
My Subnet Mask
Provided by your ISP. Enter the IP address here.
7.
Connection ID (optional)
8.
Disconnect after X….
The Disconnect feature is used to automatically disconnect the
Router from your ISP when there is no activity for a specified
period of time. For instance, placing a check mark next to this
option and entering “5” into the minute field will cause the Router
to disconnect from the Internet after five minutes of no Internet
activity. This option should be used if you pay for your Internet
service by the minute.
10
11
35
section
Provided by your ISP. If your ISP did not give you a connection
ID, leave this blank.
Alternate Setup Method
Setting your Connection Type if you are a Telstra® BigPond User
[Australia Only] Your user name and password are provided to you by
Telstra BigPond. Enter this information below. Choosing your state
from the drop-down menu (6) will automatically fill in your login server
IP address. If your login server address is different than one provided
here, you may manually enter the login server IP address by placing a
check in the box next to “User decide login server manually” (4) and
type in the address next to “Login Server” (5). When you have entered
all of your information, click “Apply Changes” (7). After you apply the
changes, the Internet Status indicator will read “connection OK” if
your Router is set up properly.
(1)
(2)
(3)
(6)
(4)
(5)
(7)
1.
Select your State
Select your state from the drop-down menu (6). The “Login
Server” box will automatically be filled in with an IP address.
If for some reason this address does not match the address
that Telstra has given, you can manually enter the login server
address. See “User Decide Login Server Manually” (4).
2.
User Name
Provided by your ISP. Type in your user name here.
36
Alternate Setup Method
3.
Password
Type in your password and retype it into the “Retype Password”
box to confirm it.
4.
User Decide Login Server Manually
Setting Custom Domain Name Server (DNS) Settings
A “Domain Name Server” is a server located on the Internet that
translates Universal Resource Locater (URLs) like “www.belkin.com”
to IP addresses. Many Internet Service Providers (ISPs) do not require
you to enter this information into the Router. The “Automatic from ISP”
box (1) should be checked if your ISP did not give you a specific DNS
address. If you are using a static IP connection type, then you may
need to enter a specific DNS address and secondary DNS address for
your connection to work properly. If your connection type is dynamic
or PPPoE, it is likely that you do not have to enter a DNS address.
Leave the “Automatic from ISP” box checked. To enter the DNS address
settings, uncheck the “Automatic from ISP” box and enter your DNS
entries in the spaces provided. Click “Apply Changes” (2) to save
the settings.
(1)
(2)
37
10
11
section
If your login server IP address is not available in the “Select Your
State” drop-down menu (6), you may manually enter the login
server IP address by placing a check in the box next to “User
decide login server manually” and type in the address next to
“Login Server” (5).
Alternate Setup Method
Configuring your WAN Media Access Controller
(MAC) Address
All network components including cards, adapters, and routers, have
a unique “serial number” called a MAC address. Your Internet Service
Provider may record the MAC address of your computer’s adapter and
only let that particular computer connect to the Internet service. When
you install the Router, its own MAC address will be “seen” by the
ISP and may cause the connection not to work. Belkin has provided
the ability to clone (copy) the MAC address of the computer into the
Router. This MAC address, in turn, will be seen by the ISP’s system as
the original MAC address and will allow the connection to work. If you
are not sure whether your ISP needs to see the original MAC address,
simply clone the MAC address of the computer that was originally
connected to the modem. Cloning the address will not cause any
problems with your network.
38
Alternate Setup Method
Cloning your MAC Address
To clone your MAC address, make sure that you are using the computer
that was ORIGINALLY CONNECTED to your modem before the Router
was installed. Click the “Clone” button (1). Click “Apply Changes” (3).
Your MAC address is now cloned to the Router.
Entering a Specific MAC Address
(2)
(1)
(3)
10
11
39
section
In certain circumstances you may need a specific WAN MAC address.
You can manually enter one in the “MAC Address” page. Type in a
MAC address in the spaces provided (2) and click “Apply Changes” (3)
to save the changes. The Router’s WAN MAC address will now be
changed to the MAC address you specified.
Using the Web-Based Advanced User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do
not type in anything else such as “http://” or “www”) then press the
“Enter” key.
You will see the Router’s home page in your browser window.
Viewing the LAN Settings
Clicking on the header of the LAN tab (1) will take you to the LAN
tab’s header page. A quick description of the functions can be
found here. To view the settings or make changes to any of the LAN
settings, click on “LAN Settings” (2) or to view the list of connected
computers, click on “DHCP Client List” (3).
(1)
(2)
(3)
40

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2005:01:18 09:50:59+08:00
Create Date                     : 2005:01:18 09:50:33+08:00
Title                           : P74688_F5D7230-4-1223.indd
Creator                         : Adobe InDesign CS (3.0)
Producer                        : Adobe PDF Library 6.0
Page Count                      : 15
Mod Date                        : 2005:01:18 09:50:59+08:00
Creation Date                   : 2005:01:18 09:50:33+08:00
Metadata Date                   : 2005:01:18 09:50:59+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools