Delta Electronics LMWU300 WLAN 802.11b USB Adapter User Manual 1

Delta Networks, Inc. WLAN 802.11b USB Adapter 1

Manual

Quick User GuideINSTALLATION PROCEDURESInstalling the Driver Under Windows 981. Plug the Wireless USB Adapter into the USB port of a notebook or desktop PC.2. The Add New Hardware Wizard indicates that Windows have recognized a new hardware device.3. Instruct the Wizard to search for the best driver for your device.4. Insert the Driver CD into your CD-ROM drive.5. Specify the location of the drivers.6. Click the Next button when Windows is ready to install the driver.7. A dialog will inform you that the installation is complete.Installing the Driver Under Windows 20001. Plug the Wireless USB Adapter into the USB port of a notebook or desktop PC.2. The Found New Hardware Wizard indicates that Windows have recognized a newhardware device.3. Instruct the Wizard to search for a suitable driver for your device.4. Insert the Driver CD into your CD-ROM drive.5. Specify the location of the drivers.6. Click the Next button when Windows have located the driver.7. Windows may display the message "Digital Signature Not Found". Ignore it by clicking "Yes".8. A dialog will inform you that the installation is complete.Installing the Driver Under Windows ME1. Plug the Wireless USB Adapter into the USB port of a notebook or desktop PC.2. The Add New Hardware Wizard indicates that Windows have recognized a new hardware device.3. Instruct the Wizard to search for the location of the driver for your device.4. Insert the Driver CD into your CD-ROM drive.5. Specify the location of the drivers.6. Click the Next button when Windows is ready to install the driver.7. A dialog will inform you that the installation is complete.MW110 V00WU Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of thefollowing measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.CUATION STATEMENTFCC Radiation Exposure Statement:To assure continued compliance, (example - use only shielded interfacecables when connecting to computer or peripheral devices). Any changes ormodifications not expressly approved by the party responsible forcompliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.This transmitter must not be co-located or operating in conjunction with anyother antenna or transmitter.
CONFIGURATION AND MONITORHow to Install the Configuration and Monitor Utility1.Find the setup.exe program in the "Config_Utility" folder on the installation CD.2.Execute the program setup.exe to do the installation.3.Run the Configuration and Monitor Utility under Start -> Program -> Wireless 802.11 USB Utility -> Configuration & Monitor Utility.Using the Configuration and Monitor UtilityThe configuration and monitor utility appears as an icon on the system tray ofWindows every time the Wireless USB Adapter is running. 1.Double-click the icon on the system tray of Windows.2.The Configuration and Monitor screen 3.The Statistics screen is shownis shown below. below. 4. The Site Survey screen is shown below. 5.The Encryption screen is shown below.6.The Advanced screen is shown 7.The Version screen is shown below. below.How to Uninstall the Configuration and Monitor ApplicationGo to Start -> Programs -> Wireless 802.11 USB -> Uninstall.How to do firmware upgrage1.Go to Start -> Programs -> Wireless 802.11 USB -> Firmware Upgrade Utility2.The Window of Firmware Upgrade Utility will appear. 3.Click the Upgrade button. An open file dialog appears. Open the ***.rom file which contains the new firmware.4.Once the upgrade procedure has been completed successfully, the device will be working with the new firmware.FIRMWARE UPGRADE UTILITY2 3

Navigation menu