Denon Avr 3808 Users Manual
AVC-3808 to the manual 589728aa-f630-4707-8231-6f5b8b741808
2015-01-23
: Denon Denon-Avr-3808-Users-Manual-221478 denon-avr-3808-users-manual-221478 denon pdf
Open the PDF directly: View PDF 
.
Page Count: 44
| Download | |
| Open PDF In Browser | View PDF |
DENON AVR control protocol Ver. 5.2.0_a Application model : AVR-3808/AVC-3808 Application terminal: RS-232C/ Ethernet Connector specification Ⅰ. RS-232C Connector type: DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC ) Communication format: Synchronous system : Tone step synchronization Communication system : A half duplex Communication speed : 9600bps Character length : 8 bits Parity control : None Start bit : 1 bit Stop bit : 1 bit Communication procedure : Non procedural Communication data length : 135 bytes (maximum) Version 5.2.0 5.2.0_a Date 06.Jul.’07 23.Jan.’08 Contents Original 1.Added NSE,NSB,NSC for iRadio Control. 2.Corrected the Command of IPE,IPA for iPod Control. 3.Added Response MS Command for DTS Mode. 4.Corrected the Response Command of PSMODE. -1- Page 23,39 24,40,41,42,43 30,31 32 Ⅱ. Ethernet Connector type ： RJ-45(10BASE-T/100BASE-TX) Example ① Ethernet Cross cable PC Example ② AVR/AVC HUB PC AVR/AVC Ethernet Straight cable Communication format Communication Communication Communication Communication ： system speed port data length : : : : Ethernet Straight cable A half duplex 10Mbps/100Mbps TCP port 23 (telnet) 135bytes (maximum) -2- NETWORK SETUP of AVR-4308 >Procedure of Network Setup mode. (1)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and GUI) (2)Select “Network Setup > Detail” . (3)Set parameters described below."ON"---Use this setting when DHCP server is on the local network. "OFF"---Use this setting when DHCP server is not on the local network. When sets "OFF”, please set IP address. When sets "ON”, you can confirm the IP address that is set by server. When sets "OFF”, please set Subnet Mask. When sets "ON”, you can confirm the Subnet Mask that is set by server. Set the address of Gateway when Gateway is on the local network. Do not set this parameter when Gateway is not on the local network. Do not set this parameter. Do not set this parameter. Set this parameter "OFF". (1)Press MENU button, then Menu appears on FL-display (and GUI) (2)Select “Manual Setup > Network Setup > Other > Power Saving” (3)Set parameters described below. “OFF”---Use this setting when using the AVR-4308 connected in a network. “ON”--- Use this setting when not using the AVR-4308 connected in a network. This setting is reducing the power consumption in the standby mode. -3- Ⅱ. Ethernet Connector type ： RJ-45(10BASE-T/100BASE-TX) Example ① Ethernet Cross cable PC Example ② AVR/AVC HUB PC AVR/AVC Ethernet Straight cable Communication format Communication Communication Communication Communication ： system speed port data length : : : : Ethernet Straight cable A half duplex 10Mbps/100Mbps TCP port 23 (telnet) 135bytes (maximum) -4- NETWORK SETUP of AVR-3808 >Procedure of Network Setup mode. (1)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and GUI) (2)Select “Network Setup > Detail” . (3)Set parameters described below. "ON"---Use this setting when DHCP server is on the local network. "OFF"---Use this setting when DHCP server is not on the local network. When sets "OFF”, please set IP address. When sets "ON”, you can confirm the IP address that is set by server. When sets "OFF”, please set Subnet Mask. When sets "ON”, you can confirm the Subnet Mask that is set by server. Set the address of Gateway when Gateway is on the local network. Do not set this parameter when Gateway is not on the local network. Do not set this parameter. Do not set this parameter. Set this parameter "OFF". (1)Press MENU button, then Menu appears on FL-display (and GUI) (2)Select “Manual Setup > Network Setup > Other > Power Saving” (3)Set parameters described below. “OFF”---Use this setting when using the AVR-3808 connected in a network. “ON”--- Use this setting when not using the AVR-4308 connected in a network. This setting is reducing the power consumption in the standby mode. -5- Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT. RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR) if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller. The RESPONSE should be sent within 200ms of receiving the COMMAND. *The form of RESPONSE presupposes that it is the same as that of EVENT. Basic specification: The command by ASCII CODE, parameter expression *ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs, AND carriage return (0x0D) --- It is used only as a pause sign. Command structure: COMMAND + PARAMETER + CR (0x0D) COMMAND: ASCII CODE of 2 characters Ex. SI : Select Input source MS : surround Mode Setting MV : Master Volume setting PW : system PoWer setting PARAMETER : ASCII CODE ( up to 25 characters) ex. DVD : function name SUPER STADIUM : surround mode name *Special Parameter--- ? : for request command -6- The example of a command * is the meaning of 0x0D. SIDVD : Select Input source DVD MSSTEREO : surround Mode Set to STEREO MVUP : Master Volume UP PWON : system PoWer ON PWSTANDBY : system PoWer STANDBY SI? : Request command for now playing input source >> Return RESPONSE ‘SI*** ’ -7- Others A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50". D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel volume of all channels , It described in B) ) returns as EVENT. E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME does NOT return. F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return. G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned. H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to the another request commands(ex. SV command). I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”. J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three ASCII characters as bellows. Ex. MASTER VOLUME = +1.0dB : MV81 +0.5dB : MV805 0dB : MV80 -0.5dB : MV795 -1.0dB : MV79 | | -79.5dB : MV005 -80.0dB : MV00 --: MV99 * At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual. K) Four seconds later, please transmit the next COMMAND after transmitting a power on COMMAND（PWON）. -8- COMMAND and PARAMETER list COMMAND PW PARAMETER function example ON POWER ON/STANDBY change PWON STANDBY PWSTANDBY ? Return PW Status PW? MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP DOWN MVDOWN ** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80 ? Return MV Status MV? CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP FL DOWN ---FRONT Lch CVFL DOWN FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50 FR UP CVFR UP FR DOWN ---FRONT Rch CVFR DOWN FR ** **:38 to 62 by ASCII , 50=0dB CVFR 50 C UP CVC UP C DOWN ---CENTERch CVC DOWN C ** **:38 to 62 by ASCII , 50=0dB CVC 50 SW UP CVSW UP SW DOWN ---SUBWOOFERch CVSW DOWN SW ** **:00,38 to 62 by ASCII , 50=0dB,00=OFF CVSW 50 SL UP CVSL UP SL DOWN ---SURROUND Lch CVSL DOWN SL ** **:38 to 62 by ASCII , 50=0dB CVSL 50 SR UP CVSR UP SR DOWN ---SURROUND Rch CVSR DOWN SR ** **:38 to 62 by ASCII , 50=0dB CVSR 50 SBL UP ---SURROUND BACK Lch (SBch 2SP) CVSBL UP SBL DOWN CVSBL DOWN SBL ** **:38 to 62 by ASCII , 50=0dB CVSBL 50 SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP SBR DOWN CVSBR DOWN SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50 MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section) -9- COMMAND CV PARAMETER function SB UP ---SURROUND BACKch (SBch 1SP) SB DOWN SB ** **:00 to 99 by ASCII , 50=0dB ? Return CV Status MU ON OUTPUT MUTE ON/OFF change OFF ? Return MU Status SI PHONO Select INPUT source CD TUNER DVD HDP TV/CBL SAT VCR DVR V.AUX NET/USB XM (North America model Only) IPOD ? Return SI Status ZM ON MAIN-ZONE ON/OFF change at AVR-3808 OFF ? Return ZM Status SR PHONO REC SELECT mode set , and select source | ---The name of PARAMETER is IPOD the same as that of the time of SI COMMAND. SOURCE REC SELECT mode cancel ? Return SR Status CV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) - 10 - example CVSB UP CVSB DOWN CVSB 50 CV? MUON MUOFF MU? SIPHONO SICD SITUNER SIDVD SIHDP SITV/CBL SISAT SIVCR SIDVR SIV.AUX SINET/USB SIXM SIIPOD SI? ZMON ZMOFF ZM? SRPHONO | SRIPOD SRSOURCE SR? COMMAND SD DC SV MS PARAMETER AUTO HDMI DIGITAL ANALOG EXT.IN-1 ? AUTO PCM DTS ? DVD HDP TV/CBL SAT VCR DVR V.AUX SOURCE ? DIRECT PURE DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND NEURAL WIDE SCREEN 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB function set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) set force HDMI INPUT mode set force DIGITAL INPUT (Optical,Coaxial)mode set force ANALOG INPUT mode ---Set EXT.IN mode at AVR-3808 Return SD Status set DIGITAL INPUT AUTO mode set DIGITAL INPUT force PCM mode set DIGITAL INPUT force DTS mode Return DC Status VIDEO SELECT mode set , and select source VIDEO SELECT mode cancel Return SV Status Select SURROUND mode (North America model Only) - 11 - example SDAUTO SDHDMI SDDIGITAL SDANALOG SDEXT.IN-1 SD? DCAUTO DCPCM DCDTS DC? SVDVD SVVDP SVTV/CBL SVSAT SVVCR SVDVR SVV.AUX SVSOURCE SV? MSDIRECT MSPURE DIRECT MSSTEREO MS STANDARD MSDOLBY DIGITAL MSDTS SURROUND MS NEURAL MSWIDE SCREEN MS7CH STEREO MSSUPER STADIUM MSROCK ARENA MSJAZZ CLUB COMMAND MS VS PARAMETER CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL MPEG2 AAC ? QUICK1 QUICK2 QUICK3 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK ? MONIAUTO MONI1 MONI2 MONI? ASPNRM ASPFUL ASP? SC48P SC10I SC72P SC10P SC AUTO SC? function ---Invalid at AVR model (Japan model only) Return MS Status QUICK SELECT 1-3 MODE SELECT USER1-3 MODE MEMORY Return MSQUICK Status Set HDMI MONITOR automatic detection (Japan model only) Set HDMI MONITOR OUT-1 (Japan model only) Set HDMI MONITOR OUT-2 (Japan model only) Return VSMONITOR Status (Japan model only) Set Normal mode Set FULL mode Return VSASPECT Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolution to 720p Set Resolution to 1080p Set Resolution to AUTO Return VSSCALE Status - 12 - example MSCLASSIC CONCERT MSMONO MOVIE MSMATRIX MSVIDEO GAME MSVIRTUAL MSMPEG2 AAC MS? MSQUICK1 MSQUICK2 MSQUICK3 MSQUICK1 MEMORY MSQUICK2 MEMORY MSQUICK3 MEMORY MSQUICK ? VSMONIAUTO VSMONI1 VSMONI2 VSMONI? VSASPNRM VSASPFUL VSASP? VSSC48P VSSC10I VSSC72P VSSC10P VSSCAUTO VSSC? COMMAND PS PARAMETER TONE DEFEAT ON TONE DEFEAT OFF TONE DEFEAT ? SB:MTRX ON SB:NON MTRX SB:PL2xCINEMA SB:PL2xMUSIC SB:ON SB:OFF SB: ? CINEMA EQ.ON CINEMA EQ.OFF CINEMA EQ. ? MODE:MUSIC MODE:CINEMA MODE:GAME MODE:PRO LOGIC function PARAMETER setting TONE DEFEAT ON/OFF Return PSTONE DEFEAT Status SURROUND BACK SP MODE set Return PSSB: Status CINEMA EQ. ON/OFF Return PSCINEMA EQ.Status CINEMA / MUSIC / GAME / PL mode change (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.) ---SB=ON：PL2x mode / SB=OFF：PL2 mode --- GAME can change DOLBY PL2 & PL2x mode --- PL can change ONLY DOLBY PL2 mode Return PSMODE: Status ROOM EQ mode direct change MODE: ? ROOM EQ:AUDYSSEY ROOM EQ:BYP.LR ROOM EQ:FLAT ROOM EQ:MANUAL ROOM EQ:OFF ROOM EQ ? Return PSROOM EQ: Status BAS UP BASS UP/DOWN , direct change to **dB BAS DOWN **:00 to 99 by ASCII , 50=0dB BAS ** ---AVR-3808 can be operated from -6 to +6(44 to 56) BAS ? Return PSBAS Status PS COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) - 13 - example PSTONE DEFEAT ON PSTONE DEFEAT OFF PSTONE DEFEAT ? PSSB:MTRX ON PSSB:NON MTRX PSSB:PL2X CINEMA PSSB:PL2X MUSIC PSSB:ON PSSB:OFF PSSB: ? PSCINEMA EQ.ON PSCINEMA EQ.OFF PSCINEMA EQ. ? PSMODE:MUSIC PSMODE:CINEMA PSMODE:GAME PSMODE:PRO LOGIC PSMODE: ? PSROOM EQ:AUDYSSEY PSROOM EQ:BYP.LR PSROOM EQ:FLAT PSROOM EQ:MANUAL PSROOM EQ:OFF PSROOM EQ: ? PSBAS UP PSBAS DOWN PSBAS 50 PSBAS ? COMMAND PS PARAMETER function TRE UP PSTRE TREBLE UP/DOWN , direct change to **dB TRE DOWN PSTRE **:00 to 99 by ASCII , 50=0dB TRE ** PSTRE ---AVR-3808 can be operated from -6 to +6(44 to 56) TRE ? PSTRE Return PSTRE Status DRC AUTO PSDRC DRC direct change DRC LOW PSDRC DRC MID PSDRC DRC HI PSDRC DRC OFF PSDRC DRC ? PSDRC DCO OFF PSDCO D.COMP direct change DCO LOW PSDCO DCO MID PSDCO DCO HIGH PSDCO DCO ? PSDCO Return PSDCO Status LFE UP PSLEE LFE UP/DOWN , direct change to **dB LFE DOWN PSLFE **:00 to 99 by ASCII , 00=0dB, 10=-10dB LFE ** PSLFE ---AVR-3808 can be operated from 0 to -10 LFE ? PSLFE Return PSLFE Status EFF ON PSEFF EFFECT ON/OFF , EFFECT LEVEL direct change to **dB EFF OFF PSEFF **:00 to 99 by ASCII , 00=0dB, 10=10dB EFF ** PSEFF ---AVR-3808 can be operated from 1 to 15 EFF ? PSEFF Return PSEFF Status DEL UP PSDEL DELAY UP/DOWN , direct change to ***dB DEL DOWN PSDEL ***:000 to 999 by ASCII , 000=0ms, 300=300ms DEL *** PSDEL ---AVR-3808 can be operated from 0 to 300 DEL ? PSDEL Return PSDEL Status AFD ON PSAFD AFDM ON/OFF AFD OFF PSAFD AFD ? PSAFD Return PSAFD Status PS COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section) - 14 - example UP DOWN 50 ? AUTO LOW MID HI OFF ? OFF LOW MID HIGH ? UP DOWN 10 ? UP DOWN ** ? UP DOWN *** ? ON OFF ? COMMAND PS PARAMETER function example PAN ON PSPAN ON PANORAMA ON/OFF PAN OFF PSPAN OFF PAN ? PSPAN ? Return PSPAN Status DIM UP PSDIM UP DIMENSION UP/DOWN , direct change to **dB DIM DOWN PSDIM DOWN **:00 to 99 by ASCII , 00=0, DIM ** PSDIM ** ---AVR-3808 can be operated from 0 to 6 DIM ? PSDIM ? Return PSDIM Status CEN UP PSCEN UP CENTER WIDTH UP/DOWN , direct change to **dB CEN DOWN PSCEN DOWN **:00 to 99 by ASCII , 00=0 CEN ** PSCEN 07 ---AVR-3808 can be operated from 0 to 7 CEN ? PSCEN ? Return PSCEN Status CEI UP PSCEI UP CENTER IMAGE UP/DOWN , direct change to **dB CEI DOWN PSCEI DOWN **:00 to 99 by ASCII , 00=0.0 CEI ** PSCEI 10 ---AVR-3808 can be operated from 0.0 to 1.0 CEI? OSCEI ? Return PSCEI Status ATT ON PSATT ON SW ATT ON/OFF ATT OFF PSATT OFF ATT ? PSATT ? Return PSATT Status SWR ON PSSWR ON SW ON/OFF SWR OFF PSSWR OFF SWR ? PSSWR ? Return PSSWR Status RSZ S PSRSZ S ROOM SIZE direct change RSZ MS PSRSZ MS RSZ M PSRSZ M RSZ ML PSRSZ ML RSZ L PSRSZ L RSZ ? PSRSZ ? Return PSRSZ Status DELAY UP AUDIO DELAY UP/DOWN , direct change to ***dB PSDELAY UP DELAY DOWN ***:000 to 999 by ASCII , 000=0ms, 200=200ms PSDELAY DOWN DELAY *** ---AVR-3808 can be operated from 0 to 200 PSDELAY 200 PS COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section) - 15 - COMMAND PS PARAMETER function NIGHT OFF NIGHT MODE direct change NIGHT LOW NIGHT MID NIGHT HI NIGHT ? Return PSNIGHT Status RSTR OFF AUDIO RESTORER direct change RSTR MODE1 RSTR MODE2 RSTR MODE3 RSTR ? Return PSRSTR Status PV CN UP CONTRAST UP/DOWN , direct change to **dB CN DOWN **:44 to 56 by ASCII , 50=0 CN ** ---AVR-3808 can be operated from -6 to +6(44 to 56) CN ? Return PSCN Status BR UP BRIGHTNESS UP/DOWN , direct change to **dB BR DOWN **:00 to 12 by ASCII , 00=0 BR ** ---AVR-3808 can be operated from 0 to 12 BR ? Return PSBR Status CM UP CROMA LEVET UP/DOWN , direct change to **dB CM DOWN **:44 to 56 by ASCII , 50=0 CM ** ---AVR-3808 can be operated from -6 to +6(44 to 56) CM ? Return PSCN Status HUE UP HUE UP/DOWN , direct change to **dB HUE DOWN **:44 to 56 by ASCII , 50=0 HUE ** ---AVR-3808 can be operated from -6 to +6(44 to 56) HUE ? Return PSCN Status PV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) - 16 - example PSNIGHT OFF PSNIGHT LOW PSNIGHT MID PSNIGHT HI PSNIGHT ? PSRSTR OFF PSRSTR MODE1 PSRSTR MODE2