Denso Wave orporated DWWB005 BHT-1400-CE main board User Manual rev

Download:
Mirror Download [FCC.gov]
Document ID	2724047
Application ID	ixDfK/4bfJA9GDWVoK3N+g==
Document Description	User Manual_rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.2kB (277507 bits)
Date Submitted	2015-08-24 00:00:00
Date Available	2016-02-20 00:00:00
Creation Date	2015-08-24 10:46:30
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2015-08-24 10:46:56
Document Title	Microsoft PowerPoint - DWWB005_Installation_And_Users_Manual_150824.ppt [唯讀] [相容模式]
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ahsia

DWWB005 Installation Manual
For OEM integration only – device cannot be sold to general public.
Therefore we will ask OEM to include the following statements required
by FCC on the product and in the Installation manual Notice.
Contents
1.Land Pattern(Recommended)
2.Supply Voltage
3.Pin configuration
4.Notice
1 Land Pattern(Recommended Unit:mm)
1.Land
2. Supply Voltage
Typ.[V]
Min.[V]
Max.[V]
VBAT
3.6
3.0
4.2
VIO
1.8
1.65
1.92
Please supply
pp y a stabilized p
power supply
pp y voltage
g through
g the VBAT And VIO.
3. Pin configuration
4. Notice
Please describe the following warning on the final product which contains this module.
Contains Transmitter Mobile FCC ID:PZWDWWB005
or
Contains FCC ID:PZWDWWB005
Please describe the following warning to the manual.
When installing it in a portable equipment
[ Model Name ]
Note)
Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm.
Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules
Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.
R l
These
Th
limits
li it are designed
d i
d to
t provide
id reasonable
bl protection
t ti against
i th
harmful
f l iinterference
t f
in
i a residential
id ti l
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user‘s
‘ authority
th it tto operate
t this
thi equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for
intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be
kept as far as possible from the user body or set the device to lower output power if such function is available.
This device is intended only for OEM integrators under the following conditions:
1)The transmitter module may not be co-located with any other transmitter or antenna.
2) Module approval valid only when the module is installed in the tested host or compatible series of host which have
similar RF exposure characteristic with equal or larger antenna separation distance.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used
on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The product can be kept as far as possible from the user body or set the device to lower output power if such function is
available. The final end product must be labeled in a visible area with the following: “Contains FCC ID: PZWDWWB005”. The
grantee‘s FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Industry Canada statement:
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference
interference, and (2) this device must accept any interference received
received, including
interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-247 d‘Industrie Canada applicable aux appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for
intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be
kept as far as possible from the user body or set the device to lower output power if such function is available.
Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables
RF pour les Etats-Unis
Etats Unis et le Canada établies pour un environnement non contrôlé
contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être
augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur
la puissance de sortie la plus faible si une telle fonction est disponible.
This device is intended only for OEM integrators under the following conditions: (For module device use)
1) The transmitter module may not be co-located with any other transmitter or antenna.
2) Module approval valid only when the module is installed in the tested host or compatible series of host which have
similar RF exposure characteristic with equal or larger antenna separation distance.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de
dispositif module)
1)Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
2) Approbation du Module valable que lorsque le module est installé dans l'hôte testé ou de la serie de l’hote compatible
qui ont meme caractéristique de l'exposition aux RF avec la distance egale ou supérieure antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires.
Toutefois l'intégrateur
Toutefois,
l intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another
transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product.
In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate Canada authorization.
NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré
comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de
réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
The product can be kept as far as possible from the user body or set the device to lower output power if such function is
available. The final end product must be labeled in a visible area with the following: “Contains IC: 1551C-DWWB005”.
Plaque signalétique du produit final
L'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance
de sortie la plus faible si une telle fonction est disponible. Le produit final doit être étiqueté dans un endroit visible avec
l'inscription
suivante: "Contient des IC: 1551C-DWWB005".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual
manual.
10
Manuel d'information à l'utilisateur final
OEM doit être conscient de ne p
pas fournir des informations à l'utilisateur final q
quant à la façon
ç d'installer
L'intégrateur
ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de
l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce
manuel.
11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : Microsoft PowerPoint - DWWB005_Installation_And_Users_Manual_150824.ppt [唯讀] [相容模式]
Creator                         : ahsia
Create Date                     : 2015:08:24 10:46:30+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2015:08:24 10:46:56+08:00
Metadata Date                   : 2015:08:24 10:46:56+08:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:2a977a6d-44e3-4a35-b25f-6ecec686b121
Instance ID                     : uuid:80c18f15-a9c8-40b5-ac40-36aef004d1c0
Page Count                      : 11
Author                          : ahsia

EXIF Metadata provided by EXIF.tools