Desa Wall Mantel And Base W26Me Users Manual
W26ME to the manual 52dec09e-6365-4738-a3ec-7cb75a1cbfc0
2015-02-04
: Desa Desa-Wall-Mantel-And-Base-W26Me-Users-Manual-512637 desa-wall-mantel-and-base-w26me-users-manual-512637 desa pdf
Open the PDF directly: View PDF .
Page Count: 4
Download | |
Open PDF In Browser | View PDF |
W26ME Wall Mantel and Base ASSEMBLY AND INSTALLATION INSTRUCTIONS Shown with Light Reed Panels Shown with Dark Reed Panels Important: Read entire instruction sheet before assembling or installing mantel kit. This mantel is only approved for use with any DESA Heating Products 26" gas or electric fireplace system. Do not use mantel with any other product. This mantel kit contains the following: • Mantel pieces - unassembled and marked as follows: #1 Base #2 Right Side with arrow #3 Right Front Leg with arrow #4 Left Side with arrow #5 Left Front Leg with arrow #6 Header with arrow #7 Top #8 Top Assembly Blocks (3) #9 Header Assembly Blocks (2) #10 Fruitwood (light) Left and Right Reed Panels (2) #11 Fruitwood (light) Front Reed Panel #12 Espresso (dark) Left and Right Reed Panels (2) #13 Espresso (dark) Front Reed Panel #14 Corner Trim (4) • Hardware Kit* 12 - Metal Brackets 118937-01 24 - Screws M6 x 12 mm (1/2") 121149-01 20 - Screws M6 x 30 mm (1 1/4") 121335-01 20 - Washers M6 121336-01 1 - Allen Wrench 121337-01 *Extra hardware may be included. • Perimeter Trim Kit 113140-02 (GAB6094) If any wood pieces are missing or damaged, contact the dealer where you purchased this mantel for replacement. If hardware is missing or damaged, contact DESA Heating Products at 1-866-672-6040 for referral information. You can also visit DESA Heating Products’ technical service web site at www.desatech.com. Note: Gather all mantel pieces together before assembling mantel. WARNING: Use only 1/2" screws to attach metal angle brackets. Damage to mantel will result if other screws are used for this purpose. Assembling Mantel IMPORTANT: More than one person is required to assemble and lift mantel. Estimated assembly time: 45 minutes. When assembling mantel do not tighten screws completely until told to do so. There should be some play in the pieces to allow for proper alignment and best possible fit. It is very important that more than one person assemble mantel together. Panels must be held in proper alignment to each other while tightening screws to assure fewer gaps and proper surface alignment. When tightening screws, do not over tighten. This may cause threads to strip. For this reason, the supplied Allen wrench should be used rather than a power screwdriver. The panels have threaded inserts installed to mark your screw locations. Screws should start and turn easily in threaded holes when assembled according to instructions. Do not force screws into holes. IMPORTANT: There is a serial number label inside of right side panel and on outside package. When calling to request technical assistance or for replacement parts please have that number ready. www.desatech.com Leg Assembly 1. Lay right side panel (#2) face down on a soft surface to avoid marking finish. Attach three brackets with 1/2" screws to bottom of right front leg (#3), leaving screws slightly loose. Face brackets out toward tongued side (see Figure 1). Place right front leg over right side (#2) matching groove in leg to tongue on side, as shown in Figure 1. Align threaded holes with brackets on side. Start three 1/2" screws through brackets. Align bottom of side and leg assembly so they are flush with each other. Hold these pieces securely in alignment while tightening (but not over tightening) screws. 2. Assemble left side (#4) and left leg (#5) as described in step 1. 3. Attach 6 brackets to base (#1) at threaded hole locations using 1/2" screws leaving screws loose. Face brackets toward outside (see Figure 2). Leg Front (#3) Groove in Leg Front 1/2" Screw Tongue on Leg Side Bracket 4. Place right side/leg assembly on base and align threaded holes with brackets. Start 1/2" screws through brackets into threaded holes in side/leg assembly. Back of side/ leg assembly should be flush with back of base. Assure alignment is correct and spaces are at a minimum. Leave screws slightly loose. 5. Assemble left side/leg assembly to base following step #4. Header Assembly 1. Start two 1 1/4" screws with washers through header assembly block (#9) into threaded inserts on right side of mantel. Repeat for left side (see Figure 3). 2. With arrow pointing up, place header (#6) into position on top of leg assemblies and against header assembly block (#9) (see Figure 3). Start two 1 1/4" screws with washers through header assembly blocks (#9) into threaded inserts in header. Hold header in proper alignment with leg assemblies and tighten, leaving screws slightly loose. Header Assembly Block (#9) Header (#6) Washer 1 1/4" Screw Leg Side (#2) Figure 1 - Right and Left Leg Assemblies Figure 3 - Attaching Header Right Side/Leg Assembly Bracket Base (#1) 1/2" Screw Figure 2 - Leg Assembly to Base www.desatech.com 122025-01A Mantel Top Assembly 1. Start two 1 1/4" screws with washers through each of the three header assembly blocks (#8) and into threaded inserts on mantel as shown in Figure 4. 2. Place mantel top (#7) on mantel assembly. Align back of top with back of sides. Using six 1 1/4" screws with washers, install two in each header assembly block (#8) (see Figure 4). Make sure all pieces are aligned properly and tighten all screws. Mantel Top (#7) Top Assembly Blocks (#8) Reed Installation 1. Mantel kit contains two sets of reed panels. A dark set (Espresso) and a light set (Fruitwood). Determine which set you prefer. Store second set in safe, dry location on a flat surface to interchange in the future if you so desire. 2. Slide front reed panel (#11 or #13) into track on front of mantel top (see Figure 5). 3. Slide left and right reed panels (#10 or #12) into tracks on sides of mantel top. Be sure panel colors match. 4. Install 4 corner trim pieces (#14) by sliding onto dovetail guide on mantel top (see Figure 5). Corner pieces should slide on easily. Do not apply excessive force to prevent breakage. Note: Reed panels can be changed after installation. Washer 1 1/4" Screw Mantel Side Assembly Figure 4 - Attaching Mantel Top Finishing Mantel Figure 5 - Installing Reed Panels Starting with left side leg assembly, tighten screws using Allen wrench provided. Tighten screws on the right side leg assembly, header, top assembly and base. 122025-01A Electric Fireplace Installation This mantel can be used with any DESA Heating Products 26" electric fireplace. Electric fireplaces install from the front of mantel. To install electric fireplace see fireplace instruction manual. Use caution when positioning fireplace on base. Base may scratch easily. www.desatech.com Gas Fireplace Installation 1. Fireplace should be fully assembled. See Assembling Fireplace in fireplace owner’s manual. 2. Place mantel base close to installation location. See fireplace owner’s manual for installation clearances. Leave enough room to insert fireplace from back of mantel. 3. Install gas line. See Connecting to Gas Supply in fireplace owner’s manual. Remember to leave access to the gas shutoff valve somewhere on the base or where it is accessible to the user. 4. Check for leaks. See Checking Gas Connections in fireplace owner’s manual. 5. Position fireplace inside mantel (see Figure 6). Carefully position gas lines. Important: Use caution when positioning fireplace on base. Base may scratch easily. Make sure fireplace is in proper position within mantel opening before continuing with installation. 6. Fireplace with louver door: Lower bottom louver door. Use two screws provided in hardware package and attach fireplace to wooden base. Close louver door. Fireplace with fixed louver: Before installing logs or burner assembly (see owner’s manual) remove screws securing floor to assembly. Lift floor for access to bottom of fireplace. Use two screws provided in fireplace hardware package and attach fireplace base to wooden base. Reinstall floor with screws removed previously. 7. If mantel trim has not yet been assembled, see Assembling Perimeter Trim. Place metal trim on shoulder screws. Firmly snap trim assembly over shoulder screws on fireplace. 8. Carefully push mantel and base into position against wall. Assembling Perimeter Trim 1. Remove packaging from three pieces of metal trim. 2. Locate two adjusting plates with set screws, and two shims in the hardware packet. 3. Align shim under adjusting plate as shown in Figure 7. 4. Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 7). 5. Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 7). 6. While firmly holding edges of trim together, tighten both set screws on the adjusting plate with slotted screwdriver. 7. Repeat steps 2 through 6 for other corner. Set Screws Slot Top Trim Adjusting Plate Mitered Edge Side Trim Shim Slot Figure 7 - Assembling Trim Figure 6 - Installing Fireplace DESA Heating, LLC 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 www.desatech.com 122025-01 Rev. A 06/07
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Tagged PDF : Yes XMP Toolkit : 3.1-701 About : 7e42606e-26b4-11da-a09e-bd1fcd51d28b Create Date : 2007:06:25 14:53:30-05:00 Metadata Date : 2007:06:25 14:59:15-05:00 Modify Date : 2007:06:25 14:59:15-05:00 Creator Tool : Adobe InDesign CS2 (4.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 10829 bytes, use -b option to extract) Instance ID : uuid:8cd7ba18-2356-11dc-ac37-000a95ba3bd8 Document ID : adobe:docid:indd:20e71720-24be-11dc-8d35-960ab11ce1be Rendition Class : proof:pdf Derived From Instance ID : 30794bb0-24b7-11dc-8d35-960ab11ce1be Derived From Document ID : adobe:docid:indd:30794baf-24b7-11dc-8d35-960ab11ce1be Manifest Link Form : DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream, DirectStream Manifest Placed X Resolution : 72.00, 150.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 150.00, 72.00 Manifest Placed Y Resolution : 72.00, 150.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 150.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:F2E0D04ECC8811DBA82EB23C70B60802, uuid:2B0C67531CC511DCBFAF9D9132B5D46D, uuid:59E727A9DD1311DBA7B7A54AF5399EC7, uuid:CFFD70A020A111DC9208BFFE5538AB56, uuid:59E727A9DD1311DBA7B7A54AF5399EC7, uuid:0EA33C1E1CA611DCADC0E0C4A1351BB9, uuid:0EA33C201CA611DCADC0E0C4A1351BB9, uuid:22B1F1381CB311DCADC0E0C4A1351BB9, uuid:22B1F13B1CB311DCADC0E0C4A1351BB9, uuid:2B0C674E1CC511DCBFAF9D9132B5D46D, uuid:561CC0361CC311DCBFAF9D9132B5D46D, uuid:6A0F2B581CCC11DCADC0E0C4A1351BB9 Manifest Reference Document ID : uuid:F2E0D04DCC8811DBA82EB23C70B60802, uuid:AF1844271CBA11DCBFAF9D9132B5D46D, uuid:59E727A7DD1311DBA7B7A54AF5399EC7, uuid:CFFD709F20A111DC9208BFFE5538AB56, uuid:59E727A7DD1311DBA7B7A54AF5399EC7, uuid:0EA33C1D1CA611DCADC0E0C4A1351BB9, uuid:0EA33C1F1CA611DCADC0E0C4A1351BB9, uuid:0EA33C211CA611DCADC0E0C4A1351BB9, uuid:22B1F1361CB311DCADC0E0C4A1351BB9, uuid:2B0C674D1CC511DCBFAF9D9132B5D46D, uuid:561CC0351CC311DCBFAF9D9132B5D46D, uuid:22B1F13C1CB311DCADC0E0C4A1351BB9 Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 4 Creator : Adobe InDesign CS2 (4.0.4)EXIF Metadata provided by EXIF.tools