Detection Systems F01U252567 01_DS160i DS161i_Inguide DS160/DS161 Installation Manual DS160 DS161 En US

en-us DS160_DS161_Installation_Manual_enUS_9007203538087179 DS160 Series High Performance Request‑to‑exit Detectors

it-it DS160_DS161_Installation_Manual_itIT_9007203538087179 DS160 Series High Performance Request‑to‑exit Detectors

sv-se DS160_DS161_Installation_Manual_svSE_9007203538087179 DS160 Series High Performance Request‑to‑exit Detectors

User Manual: Detection Systems DS160/DS161 Installation Manual Installation

Open the PDF directly: View PDF .
Page Count: 8

DS160/DS161 Installation Guide High Performance Request-to-Exit Sensors

1.0 Description

The DS160/161 is a passive-infrared (PIR) detector designed for Request

to Exit (REX) interior applications.

The DS160/161 is UL Listed as an access control device under the UL

294 Standard and is listed for Class I for UL Canada under ULC-S319

when it is connected to a UL approved access control system. For C-UL

listed installation applications, the REX detector shall be connected to

ULC-S319 listed compatible devices (i.e. control units, power supply and

locks).

The technology designed into the DS160/161 is based on the principal

that all objects emit infrared energy. The warmer an object is, the more

infrared energy emitted. Its PIR technology allows the DS160/161 to

detect the change in infrared energy that occurs when a person passes

through its field of view.

The DS160/161 has features such as Sequential Logic Input (SLI) to

eliminate unauthorized entry. SLI allows you to arm the detector using any

dry contact device, such as a second detector, card reader, or the access

control system. This provides better control for this type of application.

A built-in sounder can be automatically activated if the door is propped

open. The sounder can be controlled from any dry contact device. The

DS160/161 detection pattern provides dense C-shaped coverage ideal for

most REX applications. In addition, complete pattern control allows it to be

adjusted to a single zone or placed over a doorknob, for example. There

are fifteen possible coverage patterns to accommodate most applications.

This, combined with the ability to monitor the door and intelligently control

the lock, adds considerable security to these types of applications.

The DS160/161 uses Motion Analyzer II signal processing to help prevent

false activation due to environmental conditions. The relay output consists

of two Form “C” contacts that can be adjusted to latch from approximately

0.5 to 64 sec. The latch time features two modes of operation, resettable

(where the relay timer will not time out as long as someone is in the field

of view) and non-resettable (where the relay will remain latched for a fixed

period of time). The relay can also be programmed to fail safe or fail

secure in the event of power loss.

The DS160/161 provides one set of relay contacts specially protected

from EMF (voltage) spikes caused by connecting to inductive loads.

The DS160/161 may either be ceiling or wall mounted, and its pattern may

be aimed and/or masked for more effective use based upon installation

needs. It is not designed as a primary means of exit for emergency egress

applications.

The DS160/161 is available in a light grey (DS160) or a black (DS161)

enclosure along with an optional trim plate (light gray TP160 or black

TP161) that can cover a single gang box. Panic hardware must be used

with this or any other egress device.

Figure 1: Detector Component Locations

Wire

Terminals

Sounder

Sounder Volume Control

DIP Switches

Tamper Switch

LED

Lens Lock-Down Screw

O

N

1 2 3 4 5 6 7 8 9 10

2.0 Installation

1. Remove the cover using a small flat blade screwdriver.

Figure 2: Cover Removal

Insert screwdriver

here

Bottom

of

unit

2. Rotate the detector clockwise to remove it from the base.

Figure 3: Detector Removal

R

o

t

a

t

e

3. Select a mounting location.

Figure 4: Mounting Locations

Push to Exit

Alarm will Sound

Push to Exit

Alarm will Sound Push to Exit

Alarm will Sound

Push to Exit

Alarm will Sound

Above the

Door On the Ceiling Above

Double Doors

Before you mount the unit, review Section 6.0 Coverage

Patterns on page 6 for more information on the placement

and location of the DS160/161.

4. Route the wiring through the base before mounting the base to the

wall or ceiling. Refer to Step 5 on page 2 when using the optional

trim plate (TP160 or TP161).

Figure 5: Wire Routing

2 | F01U252567-01 | 9/11 DS160/DS161 Installation Guide © 2011 Bosch Security Systems, Inc.

5. When using the optional trim plate (TP160 or TP161), run the wiring

through the trim plate and into the base before mounting the base

and trim plate onto a single gang electrical box.

Figure 6: Optional Trimplate

DOOR

DOOR

DS160i/DS161i

Optional Trimplate

(TP160/TP161)

Gang box

The arrows on the base indicate its correct mounting

orientation relative to the door.

3.0 Wiring

3.1 Power, Remote Input, Door Contacts, and Tamper

Refer to Table 1 to wire the detector.

Table 1: Terminal Labels and Descriptions

Label Description

- Connect to the negative side of the power supply.

+ Connect to the positive side of the power supply. The

voltage must be between 12-30 Volts DC or AC.

R Terminal R is for Sequential Logic Input (SLI), the keycard

input or for remote control of the sounder. The contact must

be Normally Closed (NC).

Refer to Figure 7 and Section 3.3.5 Sequential Logic Input

on page 4 for more information.

D Terminal D allows the detector to monitor door contacts.

Refer to Sections 3.3.6 and 3.3.7 on page 4 for more

information. If used, these contacts must be Normally

Closed (NC) door contacts. Do not share these contacts

with any alarm systems.

T Normally Closed (NC) tamper contacts.

Figure 7: Sequential Logic Input (SLI)

D

RTT

Before wiring the unit, review Section 3.3 Wiring Examples

on page 2 for more information on the wiring of the

DS160/161.

3.2 Contact Output Wiring

The normal settings of the contact outputs change depending on the

setting of the Relay Mode Switch (S3). Refer to Section 4.3 Relay Mode

(DIP Switch 3) on page 5.

Figure 8: Contact Output Wiring

Fail Safe

(Switch 3 On) Fail Secure

(Switch 3 Off)

Power Off Power Off

Normal (No Motion) Normal (No Motion)

Motion Detected Motion Detected

NO C NC NO C NC NO C NC NO C NC

NO C NC NO C NC

NO C NC NO C NC

NO C NC NO C NC

NO C NC NO C NC

3.3 Wiring Examples

3.3.1 Basic Connection

The basic connection includes the DS160/161, a power supply, and a

magnetic lock. When the sensor sees motion, power is removed from the

magnetic lock. Relay contacts shown with Switch 3 ON (Failsafe Mode)

and Power On.

Figure 9: Basic Connection

© 2011 Bosch Security Systems, Inc. DS160/DS161 Installation Guide 9/11 | F01U252567-01 | 3

3.3.2 Spike Protection

 EMF (Voltage) Spike-Protected Relay: Use this relay when

connecting inductive loads to the detector. This relay protects the

detector from inductive loads that might deliver damaging EMF

spikes. No additional spike protection is needed.

 Non-EMF (Voltage) Spike-Protected Relay: This relay is best used

for non-inductive loads. When connecting an inductive load that is

not spike-protected, such as a magnetic door lock, to the detector,

use either a bridge rectifier (such as a KBL01) or a diode (such as a

1N4007). Refer to Figure 10 and Figure 11.

UL listed magnetic locks typically are already EMF spike-

protected, and therefore do not require the bridge rectifier

or diode as shown in Figure 10 and Figure 11. Refer to the

magnetic lock’s documentation for more information.

Figure 10: Diode Connection

Figure 11: Bridge Rectifier Connection

Failure to spike-protect the detector can shorten the life of

the relay contacts.

3.3.3 DS160/161 and a Keycard Reader

Normally, this setup is used when a keycard reader is on one side of the

door and the DS160/161 is on the other side. Either swiping a keycard or

a motion detected by the DS160/161 removes power from the magnetic

lock.

For DIP switch settings, refer to Section 4.7 Remote Input Function (DIP

Switches 2, 9, and 10) on page 6.

Figure 12: Keycard Reader Configuration

3.3.4 Direct Sounder Enable

The Direct Sounder Enable setting can be used to activate the DS160/161

sounder from a remote contact. The DS160/161 internal sounder remains

on as long as the external contacts remain open. The sounder input can

come from devices such as a door controller or door contacts. Turning the

sounder on does not affect the relay or relay timer. The direct sounder

input does not remove power from the magnetic lock.

Turning the sounder on does not affect the relay or relay

timer. The direct sounder input does not remove power

from the magnetic lock.

Figure 13: Direct Sounder Enable Configuration

To ensure the best sound quality from the sounder, tighten

all unused terminals on the terminal strip.

4 | F01U252567-01 | 9/11 DS160/DS161 Installation Guide © 2011 Bosch Security Systems, Inc.

3.3.5 Sequential Logic Input

The detector only activates by motion when the Sequential Logic Input

(Terminal R) is open, or for 10 sec after it closes. For example, when a

second detector placed before the DS160/161 activates, and for 10 sec

after it resets, the DS160/161 activates when it detects motion. Any

movement after 10 sec after the contact on Terminal R closes is ignored.

For DIP switch settings, refer to Section 4.7 Remote Input Function (DIP

Switches 2, 9, and 10) on page 6.

Figure 14: Sequential Logic Input Configuration

3.3.6 Door Monitor Contacts (First Option)

In the Monitor Door Contacts Mode, a person entering the field of view of

the detector activates the relay and timer. Door contacts connected to

Terminal D monitor if the door is open or closed. If the door is held open

and the relay timer is in the last 10 seconds of the latch time, the sounder

will turn on. In order for this to work correctly, the latch time must be set

for 16 seconds or greater (refer to section 4.3 on page 5.) The sounder

also activates if the door is opened without first activating the detector or

keycard input. The sounder remains on until the door closes or by

someone moving in the field of view.

For DIP switch settings, refer to Section 4.7 Remote Input Function (DIP

Switches 2, 9, and 10) on page 6.

Figure 15: Door Monitor Contacts Configuration (First Option)

To ensure the best sound quality from the sounder, tighten

all unused terminals on the terminal strip.

3.3.7 Door Monitor Contacts (Second Option)

If the detector is activated but the door is not opened, the relay drops out

after 10 sec. If the detector is activated and the door opens, then closes,

the relay drops out after 2 sec. This prevents unauthorized people from

entering.

In this mode, the REX can be activated by either someone walking in its

field of view or from a remote device if using the R input. If using the R

input to activate the detector, switch 2 should be set in the ON position

(resettable mode).

For DIP switch settings, refer to Section 4.7 Remote Input Function (DIP

Switches 2, 9, and 10) on page 6.

Figure 16: Door Monitor Contacts Configuration (Second Option)

© 2011 Bosch Security Systems, Inc. DS160/DS161 Installation Guide 9/11 | F01U252567-01 | 5

3.3.8 Disabling the Request-to-Exit

The DS160/161 can be disabled by using Terminal R and an external

device such as an access control or burglar alarm system. When the

contact connected to Terminal R closes, the DS160/161 disables after a

10-sec delay. The DS160/161 returns to normal operation as described in

Section 3.3.5 Sequential Logic Input, on page 4, after the contact closes.

Figure 17: Disabling the Request-to-Exit

The NFPA 101 Life Safety Code requires secured doors to

have a “manual release device that shall result in direct

interruption of power to the lock - independent of the

access control system electronics”.

4.0 Switch Settings

You can change the switch settings by sliding the switch to the ON or OFF

position. Refer to Figure 18.

Figure 18: DIP Switch Positions

O

N

1 2 3 4 5 6 7 8 9 10

ON

OFF

4.1 LED Operation (DIP Switch 1)

 ON: LED operates normally when motion is detected.

 OFF: LED is turned off.

When LED is enabled, it will flash on and off when first

powered up. Once the flashing LED stops, the REX is

ready to be used.

4.2 Timer Reset Mode (DIP Switch 2)

 ON: The relay timer starts when the detector sees motion and

restarts if there is additional motion. The relay only drops out when

there is no more motion and the timer expires.

 OFF: The relay timer starts when the detector sees motion. It drops

out when the timer runs out, even if the motion continues. If the

motion continues, the timer restarts.

Refer to Section 4.3 Relay Mode (DIP Switch 3) to select the time period.

4.3 Relay Mode (DIP Switch 3)

 ON: The relays operate in the Fail Safe Mode. Refer to Section 3.2

Contact Output Wiring, on page 2, for more information.

 OFF: The relays operate in the Fail Secure Mode. In the secure

mode, the REX shall be installed in a manner that does not impair

the intended operation of panic hardware used in conjunction with

the REX detector. The Fail Secure Mode must be authorized by your

Local Authority Having Jurisdiction (AHJ). Refer to Section 3.2

Contact Output Wiring, on page 2, for more information.

4.4 Relay Timer (DIP Switches 4, 5, and 6)

Setting Switches 4, 5, and 6 determines the amount of time the output

relays energize (between 0.5 sec and 64 sec) when motion is detected.

Refer to Table 2 to set the relay timer.

Table 2: Relay Timer DIP Switch Settings

Time (sec) Switch 4 Switch 5 Switch 6

0.5 (Default) OFF OFF OFF

1 OFF OFF ON

2 OFF ON OFF

4 OFF ON ON

8 ON OFF OFF

16 ON OFF ON

32 ON ON OFF

64 ON ON ON

4.5 Signal Processing (DIP Switch 7)

The Signal Processing setting determines how sensitive to movement the

detector is.

 ON: High sensitivity (REX Mode)

 OFF: Low sensitivity (security sensor)

4.6 Door Secure Mode (DIP Switches 8, 9, and 10)

If the detector activates, but the door does not open, the relay drops out

after 10 sec. If the detector activates and the door opens and then closes,

the relay drops out after 2 sec. This prevents unauthorized people from

entering.

To ensure that the Door Secure Mode operates as

expected, set the relay timer (DIP Switches 4, 5, and 6) to

16 sec or longer.

 ON: If DIP Switches 8, 9, and 10 are all ON, Door Secure Mode is

enabled. Wire according to the wiring example shown in Section

3.3.7 Door Monitor Contacts (Second Option) on page 4 for door

secure.

 OFF: If DIP Switches 8, 9, and 10 are all OFF, Door Secure Mode is

disabled.

6 | F01U252567-01 | 9/11 DS160/DS161 Installation Guide © 2011 Bosch Security Systems, Inc.

4.7 Remote Input Function (DIP Switches 2, 9, and 10)

The Remote Input Function switches determine what the DS160/161 does

when the contact attached to Terminal R is closed.

 Keycard Input: An input to the Terminal R activates the detector.

Normally, this is used with a keycard reader outside of the

door/building. The internal sounder does not activate when the

keycard input is selected. The keycard inputs are affected by

Resettable/Non-resettable Mode (Switch 2). The relay remains

activated for as long as the keycard input is closed. The timer starts

when the keycard input is force activated. If Switch 2 is on, toggling

the keycard input again restarts the timer ( the suggested setting).

When Switch 2 is off, toggling the keycard input does not restart the

timer.

 Direct Sounder Enabled: The sounder is turned on for long as the

contact on Terminal R is open. It does not affect the relay or timer.

 Sequential Logic Input: The detector only activates if the

Sequential Logic Input (Terminal R) is open, or for 10 sec after it

closes again. Movement after 10 sec after the contact on Terminal R

closes is ignored.

 Monitor Door Contacts: Door contacts connected to Terminal D

monitor if the door is open or closed. If the detector activates and the

door is open when 10 sec remain on the timer, the sounder turns on.

If the door opens without activating the detector, the sounder turns

on. The sounder remains on until the door closes or the detector

activates. For this feature to work, set the timer a minimum of 16 sec.

Refer to Table 3 to set the remote input function.

Table 3: Remote Input Function DIP Switch Settings

Function Switch 9 Switch 10

Keycard Input OFF OFF

Direct Sounder Enable OFF ON

Sequential Logic Input ON OFF

Monitor Door Contacts ON ON

5.0 Complete the Installation

1. Secure the detector inside the base.

Figure 19: Secure the Detector

Secure by tightening the

lock-down screw.

R

o

t

a

t

e

Rotate the barrel to the

desired location.

2. Adjust the sounder volume.

Figure 20: Sounder Volume

O

N

1 2 3 4 5 6 7 8 9 10

To adjust the volume, turn the Volume Control with a screwdriver.

Turn clockwise to increase the volume, and counterclockwise to decrease.

To test the volume,

turn Switch 10 on

and apply power.

The sounder will turn

on as long as

Terminal R is open.

To ensure the best sound quality from the sounder, tighten

all unused terminals on the terminal strip.

3. Replace the cover and secure with a screw. Use a drill to remove a

screw knockout in the cover only, then start screw and tighten to

secure.

Figure 21: Replace and Secure Cover

Self-Tapping

Screw

(provided)

6.0 Coverage Patterns

The coverage (detection area) of the DS160/161 varies depending on the

mounting height above the floor, angle of the lens, and if the unit is

mounted on a wall above the door or on the ceiling.

The unit can also be masked to allow only some parts of the coverage

pattern to be active.

6.1 Examples

When the unit is mounted on the wall and the lens is pointed straight

down, some detection zones point toward the wall and do not detect

movement.

Figure 22: Coverage Pattern Example 1

Views of coverage pattern with the unit mounted at 7.5 ft

(2.3 m) above the floor with the "eye" pointed straight down.

Zones that are pointed toward the wall are not shown.

Mounted on

wall above door

Mounted on ceiling 2.5 ft

(.75 m) in front of the door

Front View

ALARM WILL

SOUND WHEN

DOOR IS

OPENED

4 ft

(1.2 m)

ALARM WILL

SOUND WHEN

DOOR IS

OPENED

10 ft

(3 m)

Pattern on Floor

2.5 ft

(.75 m)

5 ft

(1.5 m)

Side View

© 2011 Bosch Security Systems, Inc. DS160/DS161 Installation Guide 9/11 | F01U252567-01 | 7

The higher the unit is mounted, the larger the coverage area. Do not

mount the DS160/161 more than 15 ft (4.6 m) above the floor.

Figure 23: Coverage Pattern Example 2

Side view of coverage pattern with the unit mounted at 15 ft

(4.6 m) above the floor with the "eye" pointed straight down

5 ft

(1.5 m) 10 ft

(3 m)

Mounted on

wall above door Mounted

on ceiling

When the DS160/161 is mounted on the wall above the door, you can

move the coverage pattern away from the wall by rotating the detector’s

lens.

6.2 Masking

The DS160/161 is supplied with three masking wedges used to disable

any part of the coverage pattern. Each wedge covers approximately 25%

of the coverage pattern.

Figure 24: Masking Options

Masking

wedge Masking

wedge Masking

wedge Masking

wedge

Masking

wedge

Insert a masking wedge by placing the bottom peg in first. Then press on

the center of the wedge until it snaps into place.

Figure 25: Insert a Masking Wedge

Select a section of the lens to mask

Insert the tab on the end of the wedge

in the hole in one side of the lens

Textured side

facing out

Press here to snap

into place

Remove a wedge by placing the tip of a small screwdriver behind the

wedge and prying it up. Do not scratch the lens when removing the

wedge.

Figure 26: Remove a Masking Wedge

Insert screwdriver behind wedge

Pry up to remove

Up to three masking wedges can be used if you only want to detect in a

very small area, such as around a doorknob or crash bar.

Figure 27: Masking Wedge Usage

ALARM WILL

SOUND WHEN

DOOR IS

OPENED

Masking

wedges

The coverage pattern depends on how high the

DS160/161 is mounted, location of the unit and the position

of the detector lens. If you want a setup as shown above,

mount the DS160/161 just above the door, on the hinge

side, with the lens pointed down and slightly out.

© 2011 Bosch Security Systems, Inc.

130 Perinton Parkway, Fairport, NY 14450-9199 USA

www.boschsecurity.com

F01U252567-01

Installation Guide

9/11

DS160/DS161

Page 8 of

8

7.0 Specifications

7.1 Specifications

Input Power 12 to 30 VDC or VAC

Relay Two Form “C” contact sets rated for 1 A each at

30 VDC or VAC max for resistive loads.

Terminal Strip 26-14 AWG

Sounder Adjustable up to 70 dB at a distance of 10 ft

(3 m).

Temperature -20°F to +120°F (-29°C to +49°C). For UL and

ULC Listed installations, the temperature range is

+32°F to +120°F (0°C to +49°C).

Humidity 0-95% non-condensing

Dimensions

(HxWxD) 1.8 in. x 7 in. x 1.75 in.

(4.5 cm x 17.8 cm x 4.4 cm)

Trim plate (HxW) Optional. TP160 (light gray); TP161 (black)

3 in. x 8.25 in. (7.6 cm x 21 cm)

Current Draw for Fail Safe Mode (DIP Switch 3 ON)

State 12 VDC 30 VDC 12 VAC 30 VAC

No Motion 15 mA 19 mA 29 mA 38 mA

Alarm 23 mA 26 mA 42 mA 51 mA

Alarm and Sounder 65 mA 79 mA 101 mA 147 mA

Current Draw for Fail Secure Mode (DIP Switch 3 OFF)

State 12 VDC 30 VDC 12 VAC 30 VAC

No Motion 5 mA 9 mA 9 mA 20 mA

Alarm 33 mA 37 mA 40 mA 73 mA

Alarm and Sounder 73 mA 95 mA 95 mA 164 mA

7.2 Regulatory Notes

The unit shall be installed in accordance with National Electrical Code

ANSI/NFPA 70 and part 1 of the Canadian Electrical Code CSA C22.1,

Safety Standard for Electrical Installations.

The DS160/161 is not intended to be configured to function as a stand-

alone access control system. Connection to listed (ALVY and/or ALVY7)

compatible control units and locking devices shall be required.

It is intended to be used as an access control Request-to-Exit device only

and not for security function; as such, the DS160 should not be connected

to a burglar alarm system.

The Request-to-Exit device shall not be connected directly to a keypad for

access control function. Connection to a listed compatible access control

system is required.

The DS160/161 was not investigated by UL for special locking

arrangements in accordance with NFPA 101.

The Request-to-Exit detector was tested for UL compliance while powered

by an XF 1640EE transformer made by AmSeco.

8.0 Reading Bosch Security Systems, Inc. Product

Date Codes

For Product Date Code Information, refer to the Bosch Security Systems,

Inc. Web site at: http://www.boschsecurity.com/datecodes.