DewertOkin 82303 Bluetooth Receiver User Manual 1

DewertOkin GmbH Bluetooth Receiver 1

User manual

Bluetooth Receiver May 17, 2016 84285(-) 1 / 2 Product description The Bluetooth Receiver translates the Bluetooth® signals of a smartphone. The Bluetooth Receiver is connected to the multifunction port (MFP) on the operational drive system. Technical Specifications Approximate range: 10 m (depending on local conditions) Input voltage: 29VDC, 5.5mA-15mA, Frequency: 2.40GHz Input power: in operation: ca. 0.42W stand-by: ca. 0.16W IP20 (for use only in dry rooms) Sicherheitshinweise / Wichtige Informationen CAUTION Only use the product when you see it.Do not position this product in the proximity of combustible materials.Do not cover the Bluetooth Receiver.Use only in dry rooms.Do not open the Bluetooth Receiver.Do not make mechanical or technical changes to this product.Such changes will invalidate the operating approvals andconformity. Never use the product when it is damaged! Damagedproducts/equipment must be replaced and disposed of inaccordance with the local environmental regulations of yourcountry. Installation and initial commissioning Download the App “OKIN smart remote” from the appropriate store.Unplug the power supply for the control unit or drive system fromthe power outlet. (Electrical components may only be connectedand disconnected if the mains plug is unplugged.) Plug the Bluetooth® Receiver’s plug into the multifunction port(MFP) on the control unit or drive system.Connect the power supply for the control unit or drive system.The Bluetooth® Receiver enters pairing mode for about 120 seconds;the function LED (1) flashes. During this time, up to seven terminaldevices can be paired to a Bluetooth® Receiver. Any additional detected terminal devices would then replace the oldest devices fromthe paired list.Notice Only one terminal device can be paired during each pairing step.If no terminal device has paired with the Bluetooth® Receiver in the 120 seconds after a reset or initial start, then the receiver switches into standby mode. Standby mode can be deactivated by briefly pressing the button (2).A continually lit LED (1) indicates that a terminal device has connectedsuccessfully.Launch the app and select the receiver.OKIN-XXXXXX; the connection is then established. You may assign a new name with up to 18 characters (special characters are not allowed).You can now configure your drive system using your smartphone.Reset onto factory setting Hold button (2) down for five to six seconds until the Bluetooth® Receiver restarts. Then press button (2) again for five to six secondsuntil the function LED (1) blinks once. The function LED (1) will then blink five times to signal a restart.When you restore the default factory settings, your pairing list and user-specified Bluetooth® Receiver name will be deleted. The function LED (1) blinks once to signal a reset.Troubleshooting The Bluetooth® Receiver is not functioning. There is no mains supply voltageCheck the mains power connection. Another smartphone is interfering with the wireless radio communication.Do not operate another smartphone simultaneously.The Bluetooth® Receiver and the smartphone are too far away fromeach other.Move them closer together. The smartphone has not been programmed (in learning mode). Program the smartphoneTeach-in configuration has been carried out but there is still no functionality The teach-in programming process was not carried out properly orthe system is defective.Check that smartphone has been programmed. Reset onto factory setting Please contact your supplier or sales agent.FCC WARNING This device complies Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.Section 15.21 Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.Consult the dealer or an experienced radio/ TV technician for help. IC WARNING This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and(2) this device must accept any interference, including interference that my cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne diot pas produire de brouillage, et(2) l’utilisateur de lappareil diot accepter tout bouillage radioélectrique subi, méme si le brouillage est susceptible d’en compromettre le fonctionnement. 12 RF Exposure StatementTo maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Navigation menu