Dexter DCL2000 Series Door Closer Hold Open Arm Installation Instructions: 111036

User Manual: Dexter Installation Instructions: Dexter DCL2000 Series Door Closer Hold Open Arm Installation Installation Instructions

Open the PDF directly: View PDF PDF.
Page Count: 2

SCREW AND WASHER
FRAME
DOOR
PINION CAP
2
1
◆STANDARD INSTALLATION:PULL SIDE RIGHT INSTALLATION
POSITION OF ARMS AND INDEX SETTINGS
RIGHT HAND DOOR
10°
STANDARD CLOSING CYCLE
CLOSING
LATCH
CLOSING SPEED CONTROL
CAUTION
DO NOT BACK VALVES OUT OF
CLOSER OR A LEAK WILL RESULT
21
19
25
29
1-3/4"
152
A6
44
1-18
1
34
MODEL
BC
P
s
A
B
s
A
B
BC
DIMENSIONS"A" OPENING
DCL2000
inches mm
7"
6"
3-12"
178
152
89
TO 100°
101°TO120°
121°TO180°
Optional Hold-open arm.ldentify
direction of hold-open nut
according to mounting.
Optional Hold-open arm.ldentify
direction of hold-open nut
according to mounting.
COF HINGE PIVOT
LEFT HAND DOOR
RIGHT HAND DOOR ILLUSTRATED SAME DIMENSIONS APPLY TO LEFT HAND DOOR
MEASURED FROM HINGE DIMENSIONS ARE IN
DO NOT SCALE DRAWING
Cinches
(mm)
1.SELECT DEGREE OF DOOR.USE DIMENSIONS
SHOWN IN CHART AND ILLUSTRATION ABOVE
TO MARK LOCATION OF ATTACHING SCREWS.
ON DOOR AND FRAME PREPARE HOLES.
2.ASSEMBLE MAIN ARM TO CLOSER.
3.ATTACH CLOSER TO DOOR WITH SPEED
REGULATING VALVES TOWARD HINGE.
4.ATTACH THE FOOT OF THE FOREARM TO FRAME.
5.ADJUST LENGTH OF FOREARM TO POSITION
FOREARM AT RIGHT ANGLE TO FRAME
TIGHTEN THE SCREW OF FOREARM.
6.SNAP PINION CAP OVER SPINDLE AT BOTTOM
OF CLOSER.
7.ADJUST DOOR CLOSER.
8.LOOSEN THE INNER HEX SCREW AT THE ELBOW OF THE
FOREARM,OPEN THE DOOR TO THE ANGLE YOU NEED,THEN
TIGHEN THE INNER HEX SCREW TO HOLD THE DOOR OPEN.
REGULATING DOOR SPEED
AND LATCHING SPEED
TURN SPEED REGLATING VALVE
CLOCKWISE TO SLOW
COUNTER-CLOCKWISE TO SPEED UP
DOOR MOVEMENT
THIS VALVE CONTROLS
DOOR SWEEP SPEED
THIS VALVE CONTROLS
LATCHING SPEED
REGULATING SPRING POWER
REGULATING BC POWER
POWER ADJUSTMENT SCREW. TURN THIS
SCREW CLOCKWISE
TO INCREASE OR COUNTER CLOCKWISE TO
DECREASE.
TURN BC REGULATING VALVE CLOCKWISE TO
INCREASE OR COUNTER CLOCKWISE TO
DECREASE.NEVER CLOSE THS VALVE COMPLETELY.
SPEED REGULATING VALVES
INSTALLATION INSTRUCTIONS
ATTENTION:
ADJUST CLOSING SPEED TIME TO BETWEEN 4 TO 6 SECONDS
FROM 90° USE OF THE DOOR BY HANDICAPPED, ELDERLY OR
SMALL CHILDREN MAY REQUIRE LONGER CLOSING TIME.
MAIN ARM
FOREARM
MAIN ARM
FOREARM
9-116
230
FOOT
DCL2000 SERIES DOOR CLOSER
HOLD OPEN ARM INSTALLATION
FRAME
DOOR
DOOR
FRAME
PINION CAP
SCREW AND WASHER
1
OTHER INSTALLATION:PULL SIDE TOP JAMB INSTALLATION
12
2
OTHER INSTALLATION:PUSH SIDE PARALLEL INSTALLATION
9-116
6 1-3/4
19
13
45
A
1-78
12
34
230
152 44
MODEL DIMENSIONS"A" OPENING
DCL2000
inches mm
7-12
6
3-12"
191
152
89


 
<80
<3-14
COF HINGE PIVOT
MODEL DIMENSIONS"A" OPENING
DCL2000
inches mm
9
7-12
227
190

 
LEFT HAND DOOR ILLUSTRATED SAME DIMENSIONS APPLY TO RIGHT HAND DOOR
MEASURED FROM HINGE DIMENSIONS ARE IN
DO NOT SCALE DRAWING
Cinches
(mm)
FOOT
7-58
6-18
mm
194
156
inches
DIMENSIONS"B"
SPEED REGULATING VALVES
BC
INSTALLATION INSTRUCTIONS
1.SELECT DEGREE OF DOOR.USE DIMENSIONS
SHOWN IN CHART AND ILLUSTRATION ABOVE
TO MARK LOCATION OF ATTACHING SCREWS.
ON DOOR AND FRAME PREPARE HOLES.
2.ATTACH CLOSER TO DOOR WITH SPEED.
3.
ATTACH MAIN ARM AS FOLLOW:
(A)PLACE OPEN END WRENCH ON BOTTOM

(B) PLACE MAIN ARM ON TOP SHAFT,INSERT
ARM SCREW INTO TOP OF SHAFT AND TIGHTEN.
4.ATTACH PA PLATE TO TOP FRAME AS SHOWN.
5.
FASTEN FOREARM TO PA PLATE.
6.
ADJUST LENGTH OF FOREARM TO POSITION MAIN
ARM AT PARALLEL TO FRAME WHEN CONNECTED TO
MAIN ARM AT ELBOW.
USE WASHER AND SCREW PROVIDED TO SECURE
PIVOT CONNECTION. TIGHTEN LOCK NUT
7.
SNAP PINION CAP OVER SPINDLE AT BOTTOM.
8.LOOSEN THE INNER HEX SCREW AT THE ELBOW OF
THE FOREARM,OPEN THE DOOR TO THE ANGLE YOU
NEED,THEN TIGHTEN THE INNER HEX SCREW TO
HOLD THE DOOR OPEN.
INSTALLATION INSTRUCTIONS
LEFT HAND DOOR ILLUSTRATED
MEASURED FROM HINGE
SAME DIMENSIONS APPLY TO RIGHT HAND DOOR
DIMENSIONS ARE IN inches
DO NOT SCALE DRAWING
C
1.SELECT DEGREE OF DOOR.USE DIMENSIONS
SHOWN IN CHART AND ILLUSTRATION ABOVE
TO MARK LOCATION OF ATTACHING SCREWS.
ON DOOR AND FRAME PREPARE HOLES.
2.ASSEMBLE MAIN ARM TO CLOSER.
3.ATTACH CLOSER TO DOOR WITH SPEED
REGULATING VALVES TOWARD HINGE.
4.ATTACH THE FOOT OF THE FOREARM TO FRAME.
5.ADJUST LENGTH OF FOREARM TO POSITION
FOREARM AT RIGHT ANGLE TO FRAME
TIGHTEN THE SCREW OF FOREARM.
6.SNAP PINION CAP OVER SPINDLE AT BOTTOM
OF CLOSER.
7.ADJUST DOOR CLOSER.
8.
LOOSEN THE INNER HEX SCREW AT THE ELBOW OF THE
FOREARM,OPEN THE DOOR TO THE ANGLE YOU NEED,THEN
TIGHTEN THE INNER HEX SCREW TO HOLD THE DOOR OPEN.
1
2
SPEED REGULATING VALVES
B
9-116
19
85
A
3-38
34
230
1-38
1
35
25
COF HINGE PIVOT
s
A

1
25
1-38
35
516
34
8
18.5
(mm)

Navigation menu