Digi Portserver Ts 1 Mei Users Manual Family Quick Start Guide
1 MEI to the manual 862f7c6b-0acf-48ed-a9dd-1f1baeb136a9
2015-02-04
: Digi Digi-Portserver-Ts-1-Mei-Users-Manual-513555 digi-portserver-ts-1-mei-users-manual-513555 digi pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
What you will need Power cord (PortServer TS 16 families only) DB-9 -RJ-45 adapter Software & Documentation Quick Start Guide Ethernet cable not included PortServer TS 1 MEI (shown) PortServer TS Family Series PortServer TS 16 MEI (shown) PortServer TS PortServer TS MEI PortServer TS P MEI PortServer TS H MEI 1 Wall and brick power supply (PortServer TS families 1/2/4/8 only) PN:(1P) 90000687-88 B Set serial DIP switch (MEI versions only) according to your serial device requirements. Pinout information available on back of quick start. Switch Settings EIA-232 2 EIA-485 EIA-422/485 Full-Duplex Half-Duplex Up/On 4 * * Down/Off Connect serial device 1 2 3 4 *If switch 4 is up, termination resistor is connected. If switch 4 is down, termination resistor is not connected. INSTALL 1, 2, or 4 Port 3 Note for PortServer TS P MEI series only In EIA-232 mode, If switch 3 is down, 9V power is provided on pin 9 (DTR). If switch 3 is up, power on pin 9 is disabled and 5V power can be enabled on pin 1 (RI) 1 2 3 4 through the software interface. LEDs will flash during startup * 3 Connect power supply Connect Ethernet cable Power (green) on; power supply Status (yellow) blinking; seeking or waiting for an IP address - for status codes, see User's Guide 3 Connect power supply Connect power cord and flip power switch on INSTALL 8 or 16 Port 1 LEDs will flash during startup PortServer TS 8 Connect Ethernet cable 2 Power - steady blinking; seeking or waiting for an IP address Link - on; physical network detected 10/100 - off; 10Mbit Ethernet detected, on; 100Mbit Ethernet detected ACT - on; bad initialization, off; ready, blinking; network activity COL - on; Ethernet collision detected Insert CD RUN WIZARD Connect serial devices 1 Connect Ethernet cable Connect serial devices The PortServer TS 8/16 MEI settings are configured through the software. Complete the Quick Start Guide and go to the User's Guide for the procedure to configure the MEI ports. The ports are set to EIA-232 by default. If your device is not EIA-232, configure the MEI settings immediately after completing the Quick Start. The default settings will not harm your device, however, we recommend configuring the MEI settings immediately as a precaution. *If you need help with cabling, see other side ! 2 PortServer TS 16 MEI You must disable firewall/antivirus software before running wizard. Congratulations! Software & Documentation If you have a UNIX system and it does not use an auto-mounter, you will need to manually mount the CD. See the back of this guide for UNIX specific instructions. © Digi International Inc., 2006. Digi, Digi International, the Digi logo, and PortServer TS are trademarks or registered trademarks of Digi International, Inc. in the United States and other countries worldwide. All other trademarks are the property of their respective owners. Configuration is complete. Go to the User's Guide on the CD for more information. Follow wizard Be sure to check Digi Support for the latest firmware updates at: http://support.digi.com Accessing the CD from a UNIX System Insert CD in system CD drive 1 UNIX If your system auto mounts the CD, skip to step 5. Auto Mount programs may use the volume information to define a mount point. If the CD volume label is "Digi" then the mount point may be /cdrom/digi Software & Documentation 2 Determine your CD device 3 Common names for CD-ROM devices: NAME EXAMPLE /dev/cdrom /dev/cdrom /dev/cdrom/cdromn /dev/cdrom/cdrom1 /dev/cdn /dev/cd0 /dev/dsk/cktmdn /dev/c1t2d0 Identify the mount-directory. Some common pre-existing mount points: /mnt/cdrom /cdrom Or create your own: mkdir /mnt/mycdrom To list descriptions of devices: AIX: lscfg HPUX: - Make sure you have administrator privileges and your PATH includes /usr/sbin ioscan -funC disk Solaris: Most Solaris systems use an auto-mounter. See the man page on vold: man vold HPUX - Check to see if pfs is running ps -ef | grep pfs If not, start the daemons: pfs_mountd&; pfsd& 4 Mount the CD by entering one of the commands from the following table: Operating System 5 Command Navigate to mounted CD directory, enter: ./setup AIX mount -r -v cdrfs device mount-directory do not use mount, it will not operate correctly *HPUX pfs_mount device mount-directory See man pages for pfs and pfs_mount for more information. Linux mount device mount-directory SCO mount -r -F cdfs device mount-directory UnixWare If you see DISPLAY permission errors when running the CD, you may want to verify your DISPLAY variable is set. To set the DISPLAY variable: DISPLAY=localhost:0.0; export DISPLAY AND/OR xhost +localhost SCO mount -r -f ISO9660 device mount-directory OpenServer Solaris mount -F hsfs device mount-directory (Intel & Most systems use an auto-mounter. See the man page SPARC) on vold: man vold Pinouts Pin 1 device is the path to the device file assigned to the cdrom drive, mount-directory is the directory where the Digi CD is mounted *HPUX When finished, leave the CD directory and pfs_umount cd pfs_umount mount-directory (If you inadvertenly use umount instead of pfs_umount, kill the pfs daemons to remove the CD-ROM.) Need help with cabling? Part number 76000697 PortServer TS 8/16 ONLY RJ-45 Pin EIA-232 EIA-422/485 Full-Duplex RI DSR RTS GND TxD RxD SG CTS DTR DCD TXDRxDRTS+ GND TxD+ RxD+ SG CTS+ RTSCTS- EIA-485 Half-Duplex TXDRxDn/a GND TxD+ RxD+ SG n/a n/a n/a Digi TS EIA-232 Cable Adapter Reference Adapter Application Bay Accelar, Nortel and other DB-9 DTE devices Digi TS DB-9F Console Adapter (4-pack) Sun Sparc, Sun Ultra, terminals, printers and other Digi TS DB-25M Console Adapter (4-pack) DTE devices with DB-25 Female ports Cabling your serial devices to a 76000698 Digi Product is now simpler than ever with a Digi Cable Adapter. While many Cisco, IBM and other DTE devices with 76000699 Digi TS DB-25F custom cabling solutions can leave you DB-25 Male ports Console Adapter (4-pack) with a cable that is either too long or too Modems and other DCE devices with short for your application, the 76000700 Digi TS DB-25M Digi Cable Adapters are used with Modem Adapter (4-pack) DB-25 Female Ports commercially available CAT 5 cable of Modems and other DCE devices with 76000701 Digi TS DB-9M any length. Simply plug standard CAT 5 Modem Adapter (4-pack) DB-9 Female Ports cable into your Digi Product, connect a For use with Printers. This adapter differs 76000692 Digi TS DB-25M Cable Adapter to the other end and plug from a Console Adapter in that it utilizes the Printer Adapter (4-pack) the adapter into your device. Whether DTR signal (instead of RTS) for hardware flow control you need a crossover or straight-through 76000631 Digi TS to For use with Cisco and Sun RJ-45 Console ports. connection, or require a DB-9 or Sun Netra / Cisco Cable Also available in 8-pack and 16-pack quantities. DB-25 connector, there is a (single pack) Digi Cable Adapter solution. For additional cabling information, see the 63000042-01 RJ-45 to RJ-45 Can be used as a networking cable or combined with Cabling guide under Documentation on Straight Through one of the adapters as a serial cable. your CD. If you prefer to order cables, Ethernet Cable see our website at http://support.digi.com All RJ-45 cables and connectors are 8-pin. When using these adapters with modems or other applications that require and select Cabling. DCD on pin 1, you must turn on altpin. If altpin is turned off, the hardware signal on pin 1 becomes DSR instead of DCD. This alternative can be used if DCD is not required, and DSR is needed instead. Configure the altpin through the web interface or the command line. See the User's Guide, MEI chapter or the set flow command in the Command Reference on the Digi CD under Documentation for more information about setting the altpin. Optional 8-pin EIA-422 (Alt-4 Wire) RxD- (B) TxD+ (A) CGND no connection RxD+ (A) SGND no connection TxD- (B)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : Adobe Illustrator CS2 Create Date : 2006:10:18 11:25-05:00 Modify Date : 2006:10:18 11:27:42-05:00 Metadata Date : 2006:10:18 11:27:42-05:00 Thumbnail Width : 168 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 19696 bytes, use -b option to extract) Document ID : uuid:3B75761D235DDB11BCF2F437E268B26E Instance ID : uuid:dcbce7e5-bf2b-4625-9ef9-3bcd98aa3bf9 Derived From Instance ID : uuid:3A75761D235DDB11BCF2F437E268B26E Derived From Document ID : uuid:3975761D235DDB11BCF2F437E268B26E Format : application/pdf Title : PortServer TS Family Quick Start Guide Creator : Digi International Description : 90000687-88_B Page Count : 2 Subject : 90000687-88_B Author : Digi InternationalEXIF Metadata provided by EXIF.tools