Digital Monitoring PC0123R8 Wireless alarm sounder User Manual Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	3070828
Application ID	AcOL6QyMkP+mx2a+rcv5+w==
Document Description	Installation Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.97kB (299637 bits)
Date Submitted	2016-07-20 00:00:00
Date Available	2016-07-20 00:00:00
Creation Date	2016-06-28 14:30:00
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2016-06-28 14:30:01
Document Title	Installation Guide
Document Creator	Adobe InDesign CC 2015 (Windows)

INSTALLATION GUIDE
Description
1135 Wireless Siren
The Model 1135 Wireless Siren provides up to 110 decibels of annunciation and
comes with a wall and cover tamper, survey LED, and two batteries. Multiple
sirens can be activated simultaneously by the panel via the Trip with Panel Bell
feature.
What is Included
• One 1135 Wireless Siren
• Two 3.0V Lithium CR123A batteries
• Hardware pack and serial number labels
Programming the Siren in the Panel
Refer to the panel programming guide as needed. In Output Information, enter
an output number, output name, eight-digit serial number, supervision time,
and set the Trip with Panel Bell option to YES. Outputs operate with a 3 second
Figure 1: 1135 Wireless Siren
response time when used with the 1135.
Trip with Panel Bell Option
Select YES to have the siren follow the panel bell output and bell cutoff time. The ON/OFF state of the siren cannot be
changed via the output menu or any other panel function. Default is YES.
Installing the Siren
Tamper Switches
The 1135 is equipped with a case tamper and a wall tamper. See Figure 2. A two position
header is provided to disable the wall tamper. See Figure 3. To disable the wall tamper,
place the jumper across the two pins of the header. Disable the wall tamper if mounting
using the supplied double-sided tape.
100/110 Decibel Jumper
The siren is equipped with a 100/110 decibel (dB) jumper and a two-position header to
change the decibel output. The siren is shipped at the 110 dB output level with the jumper
placed on one pin for storage. If the 100 dB setting is required, place the jumper over both
header pins. See Figure 3.
Selecting a Location
The 1135 siren's LED survey capability allows one person to confirm
communication with the receiver. The PCB Red Survey LED turns on brightly
whenever data is sent to the receiver then immediately turns off when the
receiver acknowledgement is processed. See Figure 3. Press the tamper switch
to send data to the receiver to confirm operation. When the 1135 does not
receive an acknowledgement from the receiver, the survey LED remains on for
8 seconds to signal that communication is not established. Communication is
also faulty when the LED flashes brightly multiple times in quick succession.
Relocate the siren or receiver until the LED immediately turns off when
tampered. Proper communication between the siren and receiver is verified
when for each press or release of the tamper switch, the LED blinks
immediately on and immediately off.
Wall Tamper
Figure 2: Wall Tamper
Mounting Holes
Red Survey LED
SOUNDER
Note: Mount the siren away from metal objects. Do not install the 1135 within 4 feet of the panel
as the RF gain of the transmitter may inhibit proper communication.
Mounting the Siren
1. Remove the locking screws from the top and bottom of the siren housing
and lift the cover from the bottom to remove.
2. Install the included two 3.0V Lithium CR123A batteries. See Figure 3.
3. Mount the 1135 on a flat wall. Use the supplied screws in the mounting
hole locations shown in Figure 3, and insure the wall tamper makes
proper contact with the wall. Or, if using the supplied double-sided tape
to attach the siren to the wall, be sure to disable the wall tamper.
4. Set the cover back into place and replace the locking screws.
100/110 dB
Header
Mounting Holes
Wall Tamper
Header
Figure 3: Mounting Holes and
PCB Features
Siren Battery Power
When setting up a wireless system, it is recommended to program the siren's output number in the panel and connect
the receiver before installing the siren's batteries. Battery life expectancy for the 1135 wireless siren is 3 years when
the siren is operated for five minutes once a month. DMP wireless equipment uses two-way communication to extend
battery life. To extend battery life further, operate the siren infrequently and extend supervision time in panel
programming. Multiple on/off siren operations and extreme hot or cold environments will reduce battery life.
Observe polarity when installing the batteries. Use only 3.0V Lithium batteries, DMP Model CR123, or the equivalent
battery from a local retail outlet. For UL installations, only use #123 batteries manufactured by Energizer.
Replacing the Siren Batteries
1. Remove the locking screws from the top and bottom of the siren housing and lift the cover from the bottom to
remove.
2. Remove the old batteries and dispose of them properly. Always replace both batteries at the same time.
Caution: Do not recharge, disassemble, heat above 212°F (100°C), or incinerate the batteries. There is a risk
of fire, explosion, and burns with improper disposal.
3. Place the two CR123 batteries in the holders and press into place. See Figure 3 for the battery locations.
4. Set the cover back into place and replace the locking screws.
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.)
from all persons. It must not be located or operated in conjunction with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Listed Compliance Specifications
Commercial Burglary
The wall tamper must be enabled for commercial burglary applications. Install only on non-conductive surfaces.
Household Fire
Supervision Time must be 3 minutes for fire applications.
800 - 641 - 4282
Accessories
CR123
Patents
3.0V Lithium Battery
U. S. Patent No. 7,239,236
Certifications
FCC Part 15 CCKPC0123R8
Industry Canada 5251A-PC0123R8
ANSI/UL 1023 Household Burglar Alarm System Units
ANSI/UL 1610 Central Station Burglar Alarm Units
ANSI/UL 985 Household Fire Warning System
INTRUSION
•
FIRE
•
ACCESS
•
NETWORKS
www.dmp.com
2500 North Partnership Boulevard
Designed, Engineered and
Manufactured in Springfield, Missouri
S p r i n g fi e l d , M i s s o u r i 6 5 8 0 3 - 8 8 7 7
16255
Battery
Life Expectancy 3 Years
Type
3.0V Lithium CR123A
See Siren Battery Power for full details.
Frequency Range 905-924 MHz
Decibel Level
110 dB at 3 ft.
Dimensions
4.5” L x 4.5” W x 1.25” H
Color
White
Housing Material
Flame retardant ABS
LT-1106 1.06 © 2016 Digital Monitoring Products, Inc.
Specifications

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c111 79.158366, 2015/09/25-01:12:00
Create Date                     : 2016:06:28 14:30-05:00
Modify Date                     : 2016:06:28 14:30:01-05:00
Metadata Date                   : 2016:06:28 14:30:01-05:00
Creator Tool                    : Adobe InDesign CC 2015 (Windows)
Version ID                      : 1
Instance ID                     : uuid:4a4bf7f4-95a8-4528-9d0e-e25910e4d758
Original Document ID            : adobe:docid:indd:fc7ba0ec-0ab8-11df-be64-ab3db10a516b
Document ID                     : xmp.id:4910ff01-b19c-d440-8682-6a6e6465cb17
Rendition Class                 : proof:pdf
Contributor Resources Document ID: uuid:a32d4be7-96ab-4428-851c-c8a6ad0a1f11
Derived From Instance ID        : xmp.iid:cd499665-5b9e-ac40-ae9a-91de374d2078
Derived From Document ID        : xmp.did:B5DDB9AC9F9DE411A597E826839A8262
Derived From Original Document ID: adobe:docid:indd:fc7ba0ec-0ab8-11df-be64-ab3db10a516b
Derived From Version ID         : 1
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Windows)
History Changed                 : /
History When                    : 2016:06:28 14:30-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 2015 (Windows)

EXIF Metadata provided by EXIF.tools