Digital Monitoring PC0155 LOW POWER WIRELESS TRANSCEIVER User Manual

Digital Monitoring Products Inc LOW POWER WIRELESS TRANSCEIVER

User Manual

InstallatIon GuIde1141 Emergency Wall ButtonDescriptionThe 1141 Emergency Wall Button is a one-button wireless emergency transmitter designed to be wall-mounted. When pressed, an emergency message is sent to the EM20 Base Unit and a phone call is placed to the Central Station. The 1141 also provides an LED that can be programmed to provide visual indication that a panic alarm has been transmitted. The 1141 operates using the supplied 3.0VDC lithium batteries.CompatibilityAll DMP 1100 Series Wireless Receivers and PanelsWhat is IncludedThe 1141 Emergency Wall Button includes the following:• One 1141 Emergency Wall Button• Two 3.0V lithium CR2430 Batteries• Hardware pack• Zone name and number label• Serial number labelTransmitter Serial NumberFor your convenience, an additional pre-printed serial number label is included. Prior to installing the device, record the serial number or place the pre-printed serial number label on the panel programming sheet. This number is required during programming. As needed, use the zone name and number label to identify a specic transmitter.Programming the Transmitter in the PanelProgram the device as a zone in Zone Information during panel programming. At the Serial Number: option, enter the eight-digit serial number.At the LED Operation option select YES to turn the LED ON when an emergency signal is transmitted and acknowledged by the receiver. The LED pulses for ve minutes after the acknowledgement is received from the wireless receiver. Select NO if you do not want the LED to turn ON when a panic signal is transmitted. The panel programming default is YES. The LED always provides a single ash to indicate good communication with the 1100 Series receiver when any signal is sent.Note: When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset. If the receiver has been powered down for more than one hour, wireless transmitters may take up to an additional hour to send a supervision message unless tripped, tampered, or powered up. This operation extends battery life for transmitters. A missing message may display on the keypad until the transmitter sends a supervision message.LED Status OperationThe Status LED turns on to acknowledge a button press. See Figure 2.Mounting the TransmitterThese instructions cover installing the housing on an interior wall. Figures 3 and 4 show the housing inside and outside views.1. Install two 1/2” wide strips of double-sided tape in the indentions on the back of the base housing.2. Remove the backing from the tape and place the housing in the desired location on the wall with the LED toward the top. See Figures 3 and 5.Figure 1: 1141 Emergency Wall ButtonFigure 2: Status LED
Digital Monitoring Products 1141 Installation Guide2Installing or Replacing the BatteriesObserve polarity when installing the battery. Use only 3.0V lithium batteries, DMP Model CR2430, or the equivalent battery from a local retail outlet.Note: When setting up a wireless system, it is recommended to program zones and connect the receiver before installing batteries in the transmitters.1. If installed, remove the top housing containing the button and internal assembly. Insert a at screwdriver into the slot on the bottom of the cover and gently lift the screwdriver handle toward you while pulling the halves apart. Repeat with the slot on the top2. Using your hands, gently separate the top housing from the base.3. Turn the top housing over and loosen the top PCB snap.4. Lean the PCB forward and lift the PCB out from the bottom PCB snaps.5. Remove the old batteries and dispose of properly.6. Observing polarity, place the 3.0V lithium batteries in the holder and press into place. See Figure 6 for Battery location.7. Snap the cover back into place with LED toward the top. See Figure 6. Caution: Properly dispose of unused batteries. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Risk of re, explosion, and burns.Battery Life ExpectancyTypical battery life expectancy for DMP Model 1141 wireless transmitters is 4 years. DMP wireless equipment uses two-way communication to extend battery life.The following situations can reduce battery life expectancy:• If a receiver is unplugged, or not installed. Note: Transmitters continue to send supervision messages until a receiver returns an acknowledgement. After an hour the transmitter only attempts a supervision message every 60 minutes.• When installed in extreme hot or cold environments.The following situation can extend battery life expectancy:• Extend transmitter supervision time in panel programming.Figure 7: Transmitter PCB and BatteriesFigure 4: Screw Mount Figure 5: Installing the CoverLEDFigure 3: Velcro Mount1141 EmergencyWall buttonBuilding WallInsert small screwdriver and lift to remove cover. Do not twist.Figure 6: Removing the Cover
1141 Installation Guide Digital Monitoring Products3FCC InformationThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It must not be co-located or operated in conjunction with any other antenna or transmitter.Changes or modications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Industry Canada InformationThis device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
LT-1326 1.01 © 2013 Digital Monitoring Products, Inc.800-641-4282www.dmp.comDesigned, Engineered and Assembled in U.S.A.INTRUSION • FIRE • ACCESS • NETWORKS2500 North Partnership BoulevardSpringfield, Missouri 65803-887713365SpecicationsBattery Life Expectancy 5 years (normal operation) Type 3.0V lithium CR123A See Battery Life Expectancy for full details.Frequency Range: 903-927 MHzDimensions Transmitter Case 3.3” L x 1.6” W x 1.2” H Color WhiteHousing Material Flame retardant ABSPatentsU. S. Patent No. 7,239,236Listings and ApprovalsFCC Part 15 Registration ID CCKPC0155 Industry Canada Registration ID 5251A-PC0155

Navigation menu