Digital Security Controls 18PG9872 Smart Wireless Ceiling PIR Presence/Security Detector User Manual My

Download:
Mirror Download [FCC.gov]
Document ID	4189822
Application ID	uxK2XBRNSqZOoHZMsGQoHg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	124.49kB (1556159 bits)
Date Submitted	2019-03-05 00:00:00
Date Available	2019-03-05 00:00:00
Creation Date	2018-10-12 12:11:54
Producing Software	madbuild
Document Lastmod	2019-02-05 16:02:41
Document Title	My Document

D-307204
The PGx872 is a smart wireless ceiling PIR presence/security detector
(selected mode) that creates a 360° coverage area to detect the movement of intruders in indoor areas.
The detector has the following features.
Presence detection mode - active 15 minutes after installation
(power-up).
Built-in link quality indicators eliminate the need for the installer to
physically approach the control panel and reduce installation time.
The device supports temperature and light level reports to compatible alarm systems that support temperature and light sensors.
Tamper protection.
PowerG two-way Frequency Hopping Spread Spectrum FHSSTDMA technology.
The Advanced True Motion Recognition™ algorithm (patented) distinguishes between the true motion of an intruder and any other disturbances which may cause false alarms.
NOTE: For UL installations, the detector is for use with UL listed control units only.
A LEDs
B Light sensor
B C
Battery
D Tamper protection
E Pyro sensors
Figure 1. Internal view
Inserting or replacing the battery
If the battery is already installed, pull the isolation strip that protrudes
from the back of the detector.
1. To separate the
detector from
the mounting
bracket, rotate
the bracket anticlockwise and
pull it from the
detector.
2. Insert the battery
Figure 2. Removing the bracket
while observing
polarity.
3. Align the
bracket tabs with
the detector slots
and rotate the
detector clockwise to verify
that it is securely
attached.
NOTE: It is recommended to wait about 1 minute after battery
removal before inserting the new battery.
Caution! Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the manufacturer's instructions
and according to local rules and regulations.
Enrollment
Refer to the panel installation manual for the enrollment procedure.
A general description of the procedure is provided in the following
flow chart:
Step Procedure
See the installation manual for the alarm system that the
device is being enrolled on to ensure that the proper steps
are used.
Enter the Device Enrollment option through the specified
PGx872 Wireless ceiling PIR presence/security detector Installation Instructions
method and select the appropriate option to add the new
device.
Enroll the device by either holding the enroll button until the
enrollment is detected, or by entering the Device ID.
Select the desired Zone Number.
Configure any device parameters that are required.
Mount and test the detector. See Walk testing / local diagnostic testing for information on testing the device. In addition, see the alarm systems installation manual that the device
is enrolled on for other test procedures that are required.
NOTE: If the detector is already enrolled, you can configure the
detector parameters by programming the system, see the alarm systems installation manual for more information about device parameters.
NOTE: When enrolling the PGx972 detector to wireless panels
(WP80XX) with version 19.4 or lower, the detector will be enrolled as
motion detector, ID 120-xxxx, and labelled ‘Motion Sens’ in the panel.
conjunction with the compatible control panels HSM2HOST9,
HS2LCDRF(P) 9, HS2ICNRF(P)9, PG9920, WS900- 19, and WS900-29.
NOTE: For detailed Placement instructions refer to the control panel
reference manual.
Walk-test the coverage area by walking across the far end of the coverage pattern in both directions. The red LED lights each time your
motion is detected followed by a steady LED signal strength indication.
Battery Power Test
Performed immediately upon battery insertion and periodically after
every several hours.
The power supply is type C in accordance with EN 50131-6 Documentation – Clause 6.
Current Consumption
30 μA average quiescent , maximum 150 mA (during transmission)
Mounting the device
1.
2.
3.
4.
Mark and drill two holes in the mounting surface. If you install
tamper protection on the detector, mark and drill one hole for the
tamper protection and one hole for one of the other available
slots (see Figure 4).
Fasten the bracket to the mounting surface with the two screws.
Align the bracket tabs with the detector slots and rotate the
detector clockwise. Verify that it is securely attached (see Figure 5).
Fasten the detector to the bracket with the screw (see Figure 6).
Installation tips
Use the following as a guide for locating a suitable mounting location.
Figure 4. Fastening the bracket
Figure 3. General Guidelines
WARNING! Do not partially or completely obscure the detector’s
field of view.
WARNING! To comply with FCC and ISED Canada RF exposure compliance requirements, the PIR detector should be located at a distance
of at least 20 cm from all persons during normal operation. The antennas used for this product must not be co- located or operated in conjunction with any other antenna or transmitter.
NOTE: The PGx872 Wireless ceiling PIR presence/security detector
shall be installed and used within an environment that provides the pollution degree max 2 and overvoltages category II in NON
HAZARDOUS LOCATIONS. The equipment is designed to be
installed only by qualified service persons.
NOTE: PGx872 shall be installed in accordance with the Standard for
Installation and Classification of Residential Burglar Alarm Systems,
UL 1641.
Walk testing / local diagnostic testing
Before permanently mounting any wireless device, temporarily mount
the device and perform a walk test. Perform a walk test of the coverage area at least once a week to ensure that the detector is working
correctly.
After inserting the battery or closing the bracket, the detector will automatically enter a stability period where the LED flashes RED for 90
seconds. Walk test the coverage area, the LED lights red each time
your motion is detected followed by 3 LED blinks. The color of the 3
LED blinks indicate the received signal strength. In walk-test mode,
regardless of the LED Selection status, the LED lights upon every
motion detection. After 15 minutes the detector automatically enters
normal mode.
The following table indicates the received signal strength.
LED Response
Signal Strength
3 green LED blinks STRONG
3 orange LED blinks GOOD
3 red LED blinks
POOR
No blinks
No communication
IMPORTANT! Only GOOD or STRONG signal strengths are acceptable. If you receive a POOR signal from the device, re-locate it and
re-test until a GOOD or STRONG signal is received.
NOTE: For UL/ULC installations, only STRONG signal levels are
acceptable. After installation verify the product functionality in
Figure 5. Attaching the detector
A Tamper protection
B Bracket screw slots
C Isolation strip
D Bracket tabs
E Detector slots
Figure 7. Beam distribution at 2.7 m (8.9 ft)
Figure 6. Fastening the detector
The following table outlines the detection distance in relation to the
mounting height.
2m
3m
4 m 5m
6m
Height
6.6 ft 9.8 ft 13.1 ft 16.4 ft 19.7 ft
m 3.75 m 4.5 m 6.5 m 10 m
Radius detection distance 3.1
10.2 ft 12.3 ft 14.8 ft 21.3 ft 32.8 ft
LED Operation
LED Indications
Event
Red LED blinks
Stabilization (warm- up 90 seconds)
Red LED on 0.2 seconds Tamper open/close
Red LED on 2 seconds Intruder alarm
For instructions on displaying the temperature of zones on the correct
panel as measured by the PGx872, refer to the panel installation guide.
GENERAL
Detector Type
Four pyroelectric sensors operating in a dual separated configuration
OPTICAL
Lens Data
Fresnel type lens.
Number of beams: 120
Max. coverage
Ø20 m/360° at the maximum installation height of 6 m (19.7 ft)
ELECTRICAL
Power Supply: Type C
Internal Battery
3V Lithium battery, type CR-123A. For UL installations, use
Panasonic and GP only
Nominal Battery Capacity: 1450 mAh
Battery Life (typical use)
Minimum 1 year. For typical use (security mode), 3 years (not verified by UL).
Low Battery Threshold: 2.6 V
NOTE: Inability to connect with wireless network, or wireless link
quality no higher than 20% may significantly reduce the expected battery life.
©2018 Tyco Security Products, Toronto, Canada www.dsc.com Tech. Support: 1-800-387-3630
Figure 8. Beam distribution at 6 m (19.7 ft)
FUNCTIONAL
True Motion Event Verification
2 remote selections at panel
Alarm Period: 2 seconds
WIRELESS
Frequency
Europe and rest of world: 433- 434 MHz, 868- 869 MHz USA: 912- 919
MHz
NOTE: Only devices in frequency band 915 MHz are UL/ULC listed.
Communication Protocol: PowerG
Supervision: Signaling at 256 s intervals
Tamper Alert
Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored.
MOUNTING
Height:
2 m to 6 m (6.6 ft to 19.7 ft)
Installation Options: Ceiling surface
ENVIRONMENTAL
RF Immunity
20 V/m up to 1000 MHz, 10 V/m up to 2700 MHz
Operating Temperatures
-10 °C to 50 °C (14 °F to 122 °F).
NOTE: UL verified operation range 0 °C to 49 °C only.
Storage Temperatures
-20 °C to 60 °C (-4 °F to 140 °F).
Humidity
Average relative humidity of up to approximately 75% non-condensing. For 30 days per year the relative humidity may vary between
85% and 95% non-condensing.
For UL installations: 5% to 93% with no condensation
PHYSICAL
Size (diameter):
15 cm (5.9 in)
Weight (with battery): 110 g (3.88 oz)
Color:
White
COMPATIBLE RECEIVERS
This device can be used with DSC panels and receivers that use
PowerG technology.
NOTE: Only devices operating in band 912- 919MHz are UL/ULC listed.
UL/ULC Not es
Only model PG9872 operating in the frequency band 912-919MHz is
UL/ULC listed. The PG9872 has been listed by UL for commercial and residential burglary applications and by ULC for residential burglary applications in accordance with the requirements in the Standards UL 639 and
ULC-S306 for Intrusion Detection Units.
For UL/ULC installations use these device only in conjunction with compatible DSC wireless receivers: HSM2HOST9, HS2LCDRF(P)9, HS2ICNRF(P)
9, PG9920, WS900-19, and WS900-29. After installation verify the product
functionality in conjunction with the compatible receiver used.
FCC COM PLIANCE STATEM ENT
WARNING! Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in residential installations. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio and television reception.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause such interference, which can be verified
by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one that supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
FCC ID: F5318PG9872
Innovation Science and Economic Development Canada (ISED)
Statement
This equipment complies with FCC and ISED Canada RF radiation exposure
limits set forth for an uncontrolled environment.
This device complies with FCC Rules Part 15 and with ISED Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference that may be received or that may cause
undesired operation.
Le present appareil est conforme aux CNR d'ISED Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si
le brouillage est susceptible d'en compromettre le fonctionnement.
IC: 160A-PG9872
Europe: CE/EN (EN50131-2-2 GRADE 2, CLASS II, EN50131-6
Type C) listed PG8872: 868 MHz PG4872: 433 MHz.
According to EN 50131-1, this equipment can be applied in installed systems up to and including Security Grade 2, Environmental Class II. UK: The
PG8872 is suitable for use in systems installed to conform to PD6662 at
Grade 2 and environmental class 2 BS8243. The Power G peripheral devices
have two-way communication functionality, providing additional benefits as
described in the technical brochure. This functionality has not been tested to
comply with the respective technical requirements and should therefore be
considered outside the scope of the product’s certification.
Simplified EU declaration of conformity
Hereby, Tyco Safety Products Canada Ltd. declares that the radio equipment
type is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
internet address:
PGx872 Wireless ceiling PIR presence/security detector Installation Instructions
PG4872: http://dsc.com/pdf/1710003
PG8872: http://dsc.com/pdf/1710004
Frequency band
868.0 MHz - 868.6 MHz
868.7 MHz - 869.2 MHz
European single point of contact: Tyco Safety
XK Echt, Netherlands.
Maximum power
10 mW
10 mW
Products, Voltaweg 20, 6101
Limited Warranty
Digital Security Controls (DSC) warrants that for a period of twelve months
from the date of purchase, the product shall be free of defects in materials and
workmanship under normal use and that in fulfilment of any breach of such
warranty, DSC shall, at its option, repair or replace the defective equipment
upon return of the equipment to its factory. This warranty applies only to
defects in parts and workmanship and not to damage incurred in shipping or
handling, or damage due to causes beyond the control of DSC such as lightning, excessive voltage, mechanical shock, water damage, or damage arising
out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and
shall be in lieu of any and all other warranties, whether expressed or implied
and of all other obligations or liabilities on the part of DSC. This warranty
contains the entire warranty. Digital Security Controls neither assumes
responsibility for, nor authorizes any other person purporting to act on its
behalf to modify or to change this warranty, nor to assume for it any other
warranty or liability concerning this product. In no event shall DSC be liable
for any direct or indirect or consequential damages, loss of anticipated profits,
loss of time or any other losses incurred by the buyer in connection with the
purchase, installation or operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system be
completely tested on a regular basis. However, despite frequent testing, and
due to, but not limited to, criminal tampering or electrical disruption, it is
possible for this product to fail to perform as expected.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or
without Products and Components is copyrighted and is purchased under the
following license terms:
This End-User License Agreement (“EULA”) is a legal agreement between You
(the company, individual or entity who acquired the Software and any related
Hardware) and Digital Security Controls, a division of Tyco Safety Products
Canada Ltd. (“DSC”), the manufacturer of the integrated security systems and
the developer of the software and any related products or components
(“HARDWARE”) which You acquired. If the DSC software product
(“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied
by HARDWARE, and is NOT accompanied by new HARDWARE, You may
not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE
PRODUCT includes computer software, and may include associated media,
printed materials, and “online” or electronic documentation. Any software
provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You under the terms of that
license agreement.
By installing, copying, downloading, storing, accessing or otherwise using
the SOFTWARE PRODUCT, You agree unconditionally to be bound by the
terms of this EULA, even if this EULA is deemed to be a modification of any
previous arrangement or contract. If You do not agree to the terms of this
EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and
You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international
copyright treaties, as well as other intellectual property laws and treaties. The
SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may
have only one copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed,
accessed, displayed, run, shared or used concurrently on or from different
computers, including a workstation, terminal or other digital electronic device
(“Device”). In other words, if You have several workstations, You will have
to acquire a license for each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE
PRODUCT, but You may only have one copy per license installed at any
given time. You may use the back-up copy solely for archival purposes.
Except as expressly provided in this EULA, You may not otherwise make
copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly You may not reverse engineer, decompile, or disassemble the SOFTWARE
PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make
any changes or modifications to the Software, without the written permission
of an officer of DSC. You may not remove any proprietary notices, marks or
labels from the Software Product. You shall institute reasonable measures to
ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a
single product. Its component parts may not be separated for use on more
than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with
HARDWARE, then the SOFTWARE PRODUCT is licensed with the
HARDWARE as a single integrated product. In this case, the SOFTWARE
PRODUCT may only be used with the HARDWARE as set forth in this
EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You
may not make it available to others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this
EULA only as part of a permanent sale or transfer of the HARDWARE,
provided You retain no copies, You transfer all of the SOFTWARE
PRODUCT (including all component parts, the media and printed materials,
any upgrades and this EULA), and provided the recipient agrees to the terms
of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must
also include all prior versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate
this EULA if You fail to comply with the terms and conditions of this EULA.
In such event, You must destroy all copies of the SOFTWARE PRODUCT
and all of its component parts.
(g) Trademarks - This EULA does not grant You any rights in connection
with any trademarks or service marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the
SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are
owned by DSC or its suppliers. You may not copy the printed materials
accompanying the SOFTWARE PRODUCT. All title and intellectual property
rights in and to the content which may be accessed through use of the
SOFTWARE PRODUCT are the property of the respective content owner and
may be protected by applicable copyright or other intellectual property laws
and treaties. This EULA grants You no rights to use such content. All rights
not expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export
the SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the
laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement
shall be determined by final and binding arbitration in accordance with the
Arbitration Act, and the parties agree to be bound by the arbitrator’s decision.
The place of arbitration shall be Toronto, Canada, and the language of the
arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT
WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL
MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE
SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of the
HARDWARE, or for problems in the interaction of the SOFTWARE
PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF
RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR
CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S
ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE
AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT
ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND
FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE
ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE
ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER
WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR
LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER
WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY
OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR
TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER
WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER
NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON
BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,
STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES
INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE
SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF
CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT,
FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE
CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY
TO PROPERTY. WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due
to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected.
The term IC before the radio certification number signifies that the Industry
Canada technical specifications were met. This Class B digital apparatus complies with Canadian ICES-003. This device complies with RSS-247 of
Industry Canada. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device. Cet appareil numérique de la classe B est conforme à la norme NMB003 du Canada. Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-247. son utilisation est autorisée seulement
aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique
©2018 Tyco Security Products, Toronto, Canada www.dsc.com Tech. Support: 1-800-387-3630
reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Le PGx872 est un détecteur PIR sans fil de présence/sécurité intelligent pour plafond (mode sélectionné) qui crée une zone de couverture de 360° pour détecter le mouvement des intrus en intérieur.
Le détecteur présente les caractéristiques suivantes.
Mode Détection de présence – Actif 15 minutes après l'installation
(mise sous tension).
Les indicateurs intégrés de qualité de la liaison évitent à l'installateur de devoir se trouver à proximité physique de la centrale
et réduisent le temps d'installation.
L'appareil assure une fonction de signalement du niveau de température et de lumière aux systèmes d'alarme compatibles prenant
en charge les capteurs de température et de lumière.
Auto-protection.
Technologie bidirectionnelle Power-G Frequency Hopping Spread
Spectrum FHSS-TDMA.
L'algorithme avancé True Motion Recognition™ (breveté) fait la
distinction entre les mouvements réels d'un intrus et toute autre perturbation susceptible de déclencher de fausses alertes.
REMARQUE : Pour les installations certifiées, le détecteur ne doit
être utilisé qu'avec des unités de contrôle certifiées UL.
Voyants
Détecteur de lumière
Pile
Auto-protection
Capteurs pyroélectriques
Figure 1. Vue interne
Insertion ou remplacement de la pile
Si la pile est déjà en place, tirez sur la languette d'activation dépassant
à l'arrière du détecteur.
1. Pour détacher le détecteur du support de montage, faites tourner le
support dans le sens contraire des
aiguilles d'une montre et extrayezle du détecteur.
2. Insérez de la pile en orientant conFigure 2. Retrait du support
venablement les pôles.
3. Alignez les pattes du support sur
les encoches du détecteur et faites
tourner le détecteur dans le sens
des aiguilles d'une montre pour
vous assurer qu'il est solidement
fixé.
REMARQUE : si vous utilisez une vis pour fixer le détecteur au support, retirez-la, remplacez la batterie en orientant correctement les
pôles et fixez le détecteur au support avec la vis.
REMARQUE : Il est conseillé d'attendre 1 minute après le retrait de
la pile avant d'en insérer une neuve.
Avertissement ! risque d'explosion si vous remplacez la pile par une
pile de type incorrect. Mettez les piles usagées au rebut en suivant les
instructions du fabricant et conformément aux règles et réglementations locales.
Enregistrement
Pour des informations détaillées sur la procédure d'enregistrement,
consultez le manuel d'installation de la centrale.
Une description générale de la procédure est indiquée dans le tableau
suivant :
Étape Procédure
Consultez le manuel d'installation du système d'alarme dans
lequel l'appareil est enregistré afin de suivre la procédure
adéquate.
Utilisez la méthode préconisée pour accéder à l'option d'enregistrement de l'appareil et sélectionnez l'option correspondante pour ajouter un nouvel appareil.
Enregistrez l'appareil en maintenant la pression sur le bouton
jusqu'à ce que l'enregistrement soit détecté ou en saisissant
4
l'ID de l'appareil.
Sélectionnez le Numéro de zone voulu.
Configurez les paramètres nécessaires de l'appareil.
Montez et testez le détecteur. Pour savoir comment tester
l'appareil, consultez la section Test de déplacement / Test de
diagnostic local. Consultez également le manuel d'installation
des systèmes d'alarme dans lesquels l'appareil est enregistré
pour connaître la procédure à suivre.
REMARQUE : Si le détecteur est déjà enregistré, vous pouvez configurer ses paramètres en programmant le système. Pour plus d'informations sur les paramètres de l'appareil, consultez le manuel
d'installation des systèmes d'alarme.
REMARQUE : lors de l’enregistrement du détecteur PGx972 dans les
centrales sans fil (WP80XX) dotées de la version 19.4 ou inférieure,
celui-ci est enregistré en tant que détecteur de mouvements (ID 120xxxx) et identifié par ‘PERIF IR’ dans la centrale.
Conseils d'installation
Utilisez les informations suivantes pour identifier un emplacement de
montage adapté.
REMARQUE : Pour des instructions de positionnement détaillées, consultez le manuel de référence de la centrale.
En mode de test de déplacement, quel que soit le statut de sélection des
voyants, le voyant s'éclaire à chaque fois qu'un mouvement est détecté.
Effectuez le test de déplacement dans toute la zone de couverture en
traversant d'un bout à l'autre la zone, dans les deux directions. Le voyant rouge s'éclaire à chaque fois que votre mouvement est détecté,
puis le voyant d'indication de la puissance du signal s'éclaire. Au bout
de 15 minutes, le détecteur passe automatiquement en mode normal.
Montage de l'appareil
1.
2.
3.
4.
Marquez et percez deux trous dans la surface de montage. Si
vous installez l'autoprotection sur le détecteur, marquez et percez un trou pour l'autoprotection et un trou pour une des autres
encoches disponibles.
Fixez le support à la surface de montage avec deux vis.
Alignez les pattes du support sur les encoches du détecteur et
faites tourner le détecteur dans le sens des aiguilles d'une
montre. Vérifiez qu'il est solidement fixé.
Fixez le détecteur au support avec la vis.
Seuil pile faible : 2,6 V
REMARQUE : L'incapacité à se connecter au réseau sans fil, ou une
qualité de réception sans fil inférieure à 20 % peut réduire considérablement la durée de vie de la pile.
Test de la pile
Effectué immédiatement après l'insertion de la pile et régulièrement
toutes les quelques heures.
L'alimentation est de type C, conformément à la Documentation EN
50131-6 – Clause 6.
Consommation électrique
Consommation moyenne au repos 30 µA, 150 mA maximum (en transmission)
Figure 4. Fixation du support
Figure 3. Consignes générales
ATTENTION ! N'obstruez pas, totalement ou partiellement, le champ
de vision du détecteur.
ATTENTION ! Pour des raisons de conformité aux normes d'exposition aux fréquences radio FCC et ISED Canada, le détecteur PIR
doit être distant d'au moins 20 cm de toute personne, en conditions de
fonctionnement normales. Les antennes utilisées pour ce produit ne
doivent pas être positionnées dans un même espace, ni utilisées avec
une autre antenne ou émetteur.
REMARQUE : Le PGx872 Détecteur PIR sans fil de présence/sécurité pour plafond sera installé et utilisé dans un environnement non
dangereux où le niveau de pollution est inférieur à 2 et où il est exposé
à des tensions de catégorie II. L'équipement est conçu pour être
installé par du personnel de maintenance qualifié uniquement.
Test de déplacement / Test de diagnostic local
Avant d'installer un appareil sans fil de manière définitive, montez l'appareil provisoirement et procédez à un test de déplacement. Exécutez
un test de déplacement dans la zone de couverture au moins une fois
par semaine pour vous assurer que le détecteur fonctionne correctement.
Après avoir inséré la pile ou fermé l'appareil, le détecteur entre automatiquement dans une phase de stabilité pendant laquelle le voyant
ROUGE s'éclaire pendant 90 secondes. Marchez dans la zone. Le voyant rouge s'éclaire à chaque fois que votre mouvement est détecté,
puis clignote trois fois. La couleur des trois clignotements indique la
puissance du signal reçu.
Le tableau ci-dessous indique la puissance du signal reçu.
Voyant
Puissance du signal
Voyant vert clignotant
FORT
Voyant orange clignotant BON
Voyant rouge clignotant FAIBLE
Aucun clignotement
Pas de comm.
IMPORTANT ! Seul un signal BON ou FORT est acceptable. Si vous
recevez un signal FAIBLE de l'appareil, changez-le d'emplacement et
recommencez les tests jusqu'à obtenir un signal BON ou FORT.
REMARQUE : Pour les installations conformes UL/ULC, seul un signal FORT est acceptable. Après l'installation, vérifiez le fonctionnement du produit avec les centrales HSM2HOST9, HS2LCDRF
(P)9, HS2ICNRF(P)9, PG9920, WS900- 19, and WS900- 29. compatibles.
PGx872 Wireless ceiling PIR presence/security detector Installation Instructions
Figure 5. Assemblage du détecteur
A Auto- protection
B Orifices pour vis du support
C Languette d'isolation
D Pattes du support
E Encoches du détecteur
Figure 6. Fixation du détecteur
Le tableau ci-dessous indique la distance de détection en fonction de
la hauteur de montage.
2m
3m
4m 5m
6m
Hauteur
6,6 ft 9,8 ft 13,1 ft 16,4 ft 19,7 ft
m 3,75 m 4,5 m 6,5 m 10 m
Rayon de détection 3,1
10, 2 ft 12,3 ft 14,8 ft 21,3 ft 32,8 ft
REMARQUE : Détection certifiée UL/ULC uniquement lorsque son
rayon est de 3,35 m et que l'appareil est installé à une hauteur de
2,75 m.
Activité de la LED
Signaux lumineux
Événement
Voyant rouge clignotant
Stabilisation (préparation 90 sec)
Voyant rouge allumé 0,2 sec. Ouverture/fermeture autoprotection
Voyant rouge allumé 2 sec. Alerte intrusion
Pour savoir comment afficher sur la centrale adéquate la température
des zones, mesurée par le détecteur PGx872, consultez le guide d'installation de la centrale.
GÉNÉRALES
Type de détecteur
Quatre capteurs pyroélectriques fonctionnant dans une configuration
séparée double
OPTIQUE
Lentille
Lentille de type Fresnel.
Nombre de faisceaux : 120
Couverture max
Ø20 m/360° à la hauteur maximale d'installation de 6 m (19,7 ft)
CARACTÉRISTIQUES ÉLECTRIQUES
Alimentation : Type C
Pile interne
Pile Lithium 3V type CR-123A. Pour les installations certifiées UL,
utilisez uniquement une pile Panasonic ou GP
Capacité nominale de la pile : 1450 mAh
Autonomie (utilisation courante)
1 an minimum. Dans le cadre d'une utilisation courante (mode sécurité), 3 ans (non vérifié par UL).
Vérification des événements par True Motion Recognition
2 sélections à distance sur la centrale
Période d'alarme : 2 secondes
COMMUNICATIONS SANS FIL
Fréquence
Europe et reste du monde : 433- 434 MHz, 868-869 MHz États-Unis :
912-919 MHz
REMARQUE : Seuls les appareils utilisant la bande de fréquences
915 MHz sont certifiés UL/ULC.
Protocole de communication : PowerG
Supervision : Signaux espacés de 256 sec.
Alerte d'autoprotection
Émise en cas de sabotage et d'émission du message correspondant
jusqu'à ce que le commutateur d'auto-protection soit remis en place.
MONTAGE
Hauteur : 2 m à 6 m (6,6 ft - 19,7 ft)
Options d'installation : Surface du plafond
CONDITIONS ENVIRONNEMENTALES
Immunité aux fréquences radio
20 V/m jusqu'à 1000 MHz, 10 V/m jusqu'à 2700 MHz
Températures en fonctionnement
-10 °C à 50 °C.
REMARQUE : Fonctionnement conforme UL vérifié uniquement
entre 0 °C et 49 °C.
Températures en stockage
-20°C à 60°C
Humidité
Humidité relative moyenne jusqu'à environ 75 % sans condensation.
Pendant 30 jours par an, l'humidité relative peut varier entre 85 % et
95 % sans condensation.
Pour les installations certifiées UL : 5 % à 93 % sans condensation
Dimensions
Taille (diamètre) : 15 cm
Poids (avec pile) : 110 g
Couleur :
Blanc
RÉCEPTEURS COMPATIBLES
Cet appareil peut être utilisé avec les centrales et récepteurs DSC qui
utilisent la technologie PowerG.
REMARQUE : Seuls les appareils fonctionnant dans la bande de
fréquences 912-919 MHz sont conformes UL/ULC.
Figure 7. Distribution du faisceau à 2,7 m (8.9 ft)
Europe: CE/EN (EN50131-2-2 GRADE 2, CLASS II, EN50131-6
Type C) PG8872: 868 MHz PG4872: 433 MHz.
Selon les normes EN 50131-1, cet équipement peut être intégré dans les systèmes installés jusqu'à et y compris la classe environnementale II, niveau de
sécurité 2. Royaume-Uni: Le PG8872 convient pour l'utilisation dans les systèmes installés pour se conformer à la norme PD6662 à la classe environnementale 2 et de niveau 2 BS8243. Les dispositifs périphériques Power G
sont dotés d'une fonction de communication bidirectionnelle, offrant des
avantages supplémentaires comme décrit dans la brochure technique. Cette
fonction n'a pas été déclarée conforme aux besoins techniques respectifs et
doit, par conséquent, être exclue de la certification du produit.
Déclaration EU de Conformité Simplifiée
Le soussigné, Tyco Safety Products Canada Ltd déclare que le type d’équipement radioélectrique est conforme à la directive 2014/53/UE.
Le texte complet de la déclaration UE de conformité est disponible à l'adresse
internet suivante:
PG4872: http://dsc.com/pdf/1710003
PG8872: http://dsc.com/pdf/1710004
Bandes de fréquences
Puissance maximale
868.0 MHz - 868.6 MHz
10 mW
868.7 MHz - 869.2 MHz
10 mW
Point de contact unique en Europe: Tyco Safety Products, Voltaweg 20,
6101 XK Echt, Pays-Bas.
Figure 8. Distribution du faisceau à 6 m (19,7 ft)
CARACTÉRISTIQUES DE FONCTIONNEMENT
©2018 Tyco Security Products, Toronto, Canada www.dsc.com Tech. Support: 1-800-387-3630
El PGx872 es un detector inalámbrico infrarrojo pasivo (PIR) de presencia y seguridad inteligente para montaje en techo (modo seleccionado) que crea un área de cobertura de 360° para detectar el
movimiento de intrusos en áreas interiores.
El detector presenta las siguientes características.
Modo de detección de presencia: activar 15 minutos después de la
instalación (encendido).
Gracias a los indicadores de calidad del enlace incorporados, el
instalador no necesita acercarse físicamente al panel de control y
el tiempo de instalación se reduce.
El dispositivo es compatible con informes de temperatura y de
nivel de luz a sistemas de alarma compatibles, que admiten
sensores de temperatura y de luz.
Protección contra manipulación.
l
Tecnología TDMA bidireccional Power-G de salto de frecuencias
de espectro amplio (FHSS).
El algoritmo patentado Advanced True Motion Recognition™ distingue entre el verdadero movimiento de un intruso y cualquier otra
perturbación que pueda causar falsas alarmas.
como detector de movimiento, ID 120-xxxx y se etiquetará como
‘Motion Sens’ en el panel.
Consejos para la instalación
Utilizar la siguiente información como guía para localizar un lugar de
montaje adecuado.
NOTA: En el caso de instalaciones UL, el detector se debe utilizar
únicamente con unidades de control homologadas por UL.
A Indicadores LED
B Sensor de luz
C Batería
D Protección contra manipulación
E Sensores piroeléctricos
2.
3.
4.
para una de las otras ranuras disponibles.
Fije el soporte a la superficie de montaje con los dos tornillos.
Alinee las pestañas del soporte con las ranuras del detector y
gire el detector en el sentido horario. Verifique que esté bien
sujeto.
Con el tornillo, sujete el detector al soporte.
mentación EN 50131-6, cláusula 6.
Consumo actual
Corriente de reposo promedio 50 μA, máxima 150 mA (durante la
transmisión)
Figura 1. Vista interna
Introducción o cambio de la batería
Si la batería ya está instalada, tire de la tira de activación que sobresale de la parte posterior del detector.
1. Para separar el detector del
soporte de montaje, gire el soporte
en el sentido antihorario y extráigalo del detector.
2. Inserte la batería teniendo en
cuenta la polaridad.
Figura 2. Extracción del
3. Alinee las pestañas del soporte con
soporte
las ranuras del detector y gire el
detector en el sentido horario, para
verificar que está bien sujeto.
NOTA: Si se usa un tornillo para fijar el detector al soporte, quite el
tornillo, cambie la batería manteniendo la polaridad y fije el detector
al soporte usando el tornillo.
NOTA: Se recomienda esperar aproximadamente 1 minuto después
de extraer la batería antes de introducir la nueva.
¡Cuidado! Riesgo de explosión si se sustituye la batería por un tipo inadecuado. La eliminación de baterías usadas se debe efectuar acorde
con las instrucciones del fabricante y de conformidad con las reglas y
reglamentaciones locales.
Registro
Para información sobre el procedimiento de registro, consulte el
manual de instalación del panel.
En el siguiente diagrama de flujo se provee una descripción general
del procedimiento:
Etapa Procedimiento
Para garantizar la aplicación de las etapas apropiadas, consulte el manual de instalación del sistema de alarma en el
que el dispositivo está registrado.
Entre en la opción Registro de dispositivo por medio del
método especificado y elija la opción apropiada para
agregar el nuevo dispositivo.
Para registrar el dispositivo, mantenga presionado el botón
de registro hasta que se detecte el registro, o escriba el identificador (ID) del aparato.
Elija el número de la zona deseada.
Configure todos los parámetros del dispositivo que sean
necesarios.
Montar y probar el detector. Para obtener información
acerca de cómo probar el dispositivo, consulte Prueba de
recorrido / Prueba de diagnóstico local. Consulte también el
manual de instalación de sistemas de alarma, para comprobar si el dispositivo está registrado o para ver otros procedimientos de prueba que sean necesarios.
NOTA: Si el detector ya está registrado, puede configurar sus parámetros mediante la programación del sistema. Para más información
sobre los parámetros del dispositivo, consulte el manual de instalación
de alarmas.
NOTA: Al registrar el detector PGx972 en los paneles inalámbricos
(WP80XX) con la versión 19.4 o anteriores, el detector se registrará
PGx872 Wireless ceiling PIR presence/security detector Installation Instructions
Figura 3. Lineamientos generales
¡ADVERTENCIA! No obstaculice el campo de visión del detector de
forma parcial ni total.
¡ADVERTENCIA! Para cumplir con los requisitos de cumplimiento de
normas de exposición de FCC e ISED Canada RF, el panel de control
se debe ubicar a una distancia de al menos 20 cm de todas las personas durante el funcionamiento normal. Las antenas que se utilizan
para este producto no se deben instalar ni utilizar junto otra antena u
otro transmisor.
NOTA: El PGx872 [[[Undefined variable VariableSetsSpanish/General.ProductDesc]]] se debe instalar y utilizar en
un entorno que provea el nivel de contaminación máximo de 2 y la categoría de sobretensión II en LUGARES NO PELIGROSOS. El equipo
está diseñado para ser instalado solo por personal de servicio capacitado.
Prueba de recorrido / Prueba de diagnóstico local
Antes del montaje permanente de cualquier dispositivo inalámbrico,
móntelo temporalmente y haga una prueba de recorrido. Haga una
prueba de recorrido del detector, por lo menos una vez al semana,
para asegurarse de que el detector funciona correctamente.
Después de introducir la batería o de cerrar el dispositivo, el detector
entra automáticamente en un periodo de estabilidad cuando el indicador LED parpadea en ROJO durante 90 segundos. Al efectuar la
prueba de recorrido del área de cobertura, cada vez que se detecte su
movimiento, el indicador LED se enciende en rojo, seguido de tres destellos. El color de los tres destellos del indicador LED indican la potencia de la señal recibida.
En la siguiente tabla se indica la potencia de la señal recibida.
Respuesta del indicador LED Potencia de señal
El indicador LED verde parpadea
ALTA
El indicador LED naranja parpadea BUENA
El indicador LED verde parpadea
BAJA
Sin parpadeo
Sin comunicación
¡IMPORTANTE! Las únicas potencias de señal aceptables son
BUENA o ALTA. Si recibe una señal DÉBIL del dispositivo,
reubíquelo y vuelva a probar hasta que reciba una potencia de señal
BUENA o ALTA.
NOTA: En instalaciones de UL/ULC, solo se admite una potencia de
señal ALTA. Después de la instalación, verifique la funcionalidad del
producto junto con los paneles de control compatibles HSM2HOST9,
HS2LCDRF(P) 9, HS2ICNRF(P)9, PG9920, WS900- 19, and WS900-29.
NOTA: Para ver instrucciones de colocación, consulte el manual de
referencia del panel de control.
En el modo de prueba de recorrido, sea cual sea el estado de selección del indicador LED, este se enciende cada vez que se detecta
movimiento. Haga una prueba de recorrido del área de cobertura caminando por el extremo más lejano del patrón de cobertura en ambas
direcciones. Cada vez que se detecte su movimiento, el indicador LED
se enciende en rojo, seguido de una indicación de potencia de señal
del indicador LED. Al cabo de 15 minutos, el detector entra automáticamente en el modo normal.
Montaje del dispositivo
1.
Marque y taladre dos orificios en la superficie de montaje. Si
instala en el detector una protección contra manipulación,
marque y perfore un orificio para dicha protección y un orificio
Figura 4. Sujeción del soporte
Figura 5. Colocación del detector
A Protección contra alteración
B Ranuras de tornillos del soporte
C Banda de aislamiento
D Lengüetas del soporte
E Ranuras del detector
Figura 6. Sujeción del detector
En la siguiente tabla se indica la distancia de detección en relación
con la altura de montaje.
6 met2 metros 3 metros 4 metros 5 metros
Altura
6.6 ft
9.8ft
13.1ft
16.4 ft ros
19.7 ft
Distancia de detec- 3,1 met- 3,75 met- 4,5 met- 6,5 met- 10 metros
ros
ros
ros
ros
ción
10,2 ft 12,3 ft
14,8 ft 21,3 ft 32,8 ft
NOTA:Detección verificada por UL/ULC solo en un radio de 3,35
metros, cuando el dispositivo está instalado a una altura de 2,75 metros.
Figura 7. Distribución de haz a 2,7 metros (8.9 ft)
Utilización del LED
Indicaciones del LED
Evento
Estabilización (90 segundos de
calentamiento)
Indicador LED rojo encendido dur- Abrir o cerrar protección conante 0.2 segundos
tra manipulación
Indicador LED rojo encendido durAlarma de intruso
ante 2 segundos
Para obtener instrucciones sobre la indicación de la temperatura de
zonas en el panel correcto según las mediciones del PGx872, consulte
la guía de instalación del panel.
GENERAL
Tipo de detector
Cuatro sensores piroeléctricos que funcionan en una configuración
dual separada
ÓPTICAS
Información sobre la lente
Lente de tipo Fresnel.
Cantidad de haces: 120
Cobertura máxima
Ø20 m/360° a una altura de instalación máxima de 6 metros (19,7 ft)
ELÉCTRICAS
Fuente de alimentación: Tipo C
Batería interna
Batería de litio de 3 voltios, CR-123A. En el caso de instalaciones UL ,
utilizar solo Panasonic y GP
Capacidad nominal de la batería: 1450 mAh
Vida útil de la batería, en uso normal
Como mínimo 1 año. Para uso típico (modo de seguridad), 3 años (no
verificado por UL).
Umbral de batería baja: 2,6 voltios
El indicador LED verde parpadea
NOTA: La incapacidad de conectarse con una red inalámbrica o una
calidad de enlace inalámbrico no superior al 20% podrían reducir significativamente la vida útil prevista de la batería.
Prueba de potencia de batería
Se efectúa inmediatamente después de introducir la batería y periódicamente cada tantas horas.
La fuente de alimentación es del tipo C, de conformidad con la Docu-
©2018 Tyco Security Products, Toronto, Canada www.dsc.com Tech. Support: 1-800-387-3630
Figura 8. Distribución de haz a 6 metros (19,7 ft)
FUNCIONAL
Verificación de evento de movimiento verdadero
2 selecciones remotas en el panel
Periodo de alarma: 2 segundos
INALÁMBRICO
Frecuencia
Europa y resto del mundo: 433 a 434 MHz, 868 a 869 MHz EEUU:
912 a 919 MHz
NOTA: Solo dispositivos que funcionan en la banda de 915 MHz
están homologados por UL/ULC.
Protocolo de comunicaciones: PowerG
Supervisión: Señalización a intervalos de 256 segundos
Alerta de manipulación
Se notifica durante un evento de manipulación y en cada mensaje subsiguiente, hasta que el interruptor de seguridad se restablezca.
MONTAJE
Peso: 2 a 6 metros (6,6 - 19,7 ft)
Opciones de instalación: Superficie del techo
AMBIENTALES
Inmunidad a RF
20 V/m hasta 1000 MHz, 10 V/m hasta 2700 MHz
Temperaturas de funcionamiento
-10°C a 50°C.
NOTA: Margen de operación verificado por UL, 0 °C a 49 °C únicamente.
Temperaturas de almacenamiento
-20 °C a 60 °C
Humedad
Humedad relativa promedio de hasta un 75%, sin condensación. Durante 30 días al año, la humedad relativa puede variar entre el 85% y el
95%, sin condensación.
En el caso de instalaciones UL: 5% a 93% sin condensación
FÍSICAS
Tamaño (diámetro):
15 cm
Peso (incluida la batería): 110 gramos
Color:
Blanco
RECEPTORES COMPATIBLES
Este dispositivo se puede utilizar con paneles y receptores DSC que
utilizan la tecnología PowerG.
NOTA: Solo dispositivos que funcionan en la banda de 912 a 919
MHz están homologados por UL/ULC.
Europa: CE/EN (EN50131-2-2 GRADE 2, CLASS II, EN50131-6
Typo C) PG8872: 868 MHz PG4872: 433 MHz.
De acuerdo con las normas EN 50131-1, este equipo puede ser aplicado en
sistemas instalados hasta e incluyendo el Grado 2 de Seguridad, Clase ambiental II. Reino Unido: El modelo PG8872 es adecuado para uso en sistemas
instalados para cumplir con PD6662 en el Grado 2 y Clase ambiental 2
BS8243. Los dispositivos periféricos Power G tienen funcionalidad de comunicación de dos vías, lo que proporciona ventajas adicionales como se
describen en el folleto técnico. No se ha probado que estas funciones
cumplan con los requisitos técnicos correspondientes y, por lo tanto, deberían considerarse fuera del alcance de la certificación del producto.
Declaración UE de Conformidad Simplificada
Por la presente, Tyco Safety Products Canada Ltd declara que el typo de
equipo radioeléctrico es conforme con la Directiva 2014/53/UE.
El texto completo de la declaración UE de conformidad está disponible en la
dirección Internet siguiente:
PG4872: http://dsc.com/pdf/1710003
PG8872: http://dsc.com/pdf/1710004
Bandes de freceuncia
Potencia máxima
868.0 MHz - 868.6 MHz
10 mW
868.7 MHz - 869.2 MHz
10 mW
Punto de contacto único en Europa: Tyco Safety Products, Voltaweg 20,
6101 XK Echt, Holanda.
A PGx872 é um detector inteligente de presença/segurança PIR de
teto sem fio (modo selecionado) que cria uma área de cobertura de
360 ° para detectar o movimento de intrusos em áreas internas.
O detector tem os seguintes recursos.
Modo de detecção de presença – 15 minutos ativos após instalação
(inicialização).
Indicadores de qualidade de conexão embutidos eliminam a
necessidade de um instalador para se aproximar fisicamente do
painel de controle e reduz o tempo de instalação.
O dispositivo suporta avisos de temperatura e nível de luz para sistemas de alarme compatíveis que aceitem sensores de temperatura e luz.
Proteção contra violação.
Tecnologia FHSS-TDMA de Espectro de Alastramento com
Mudança de Frequência de duas vias Power-G.
O algoritmo avançado True Motion Recognition™ (patenteado)
diferencia os verdadeiros movimentos de um invasor e quaisquer
outros distúrbios que possam causar alarmes falsos.
OBS.: Para instalações de UL: o detector só deve ser usado com unidades de controle listada em UL.
LEDs
Sensor de luz
Bateria
Proteção contra violação
Sensores de fogo
Figura 4. Fixação do suporte
Figura 1. Visão interna
Inserir ou trocar a pilha
Se a bateria já estiver instalada, puxe a faixa de ativação que se
encontra protuberante na traseira do detector.
1. Para separar o detector do suporte
de montagem, gire o suporte em
sentido anti-horário e puxe-o do
detector.
2. Insira a bateria levando em conta a
polaridade.
Figura 2. Remoção do suporte
3. Alinhe as roscas do suporte aos
encaixes do detector e gire o
detector em sentido horário para
certificar-se de que ele está firmemente preso.
OBS.: se um parafuso for usado para prender o detector em um
suporte, remova o parafuso, substitua a bateria observando a polaridade e prenda o detector no suporte usando o parafuso.
OBS.: Recomenda-se esperar cerca de 1 minuto depois de remover a
pilha antes de inserir a nova pilha.
Cuidado! Risco de explosão se a bateria for trocada por uma de um
tipo incorreto. Descarte as baterias usadas de acordo com as
instruções do fabricante e com as regras e normas locais.
Registro
Consulte o manual de instalação do painel para aprender o procedimento de registro.
Uma descrição geral do procedimento é fornecida no fluxograma a
seguir:
Etapa Procedimento
Consulte o manual de instalação do sistema de alarme ao
qual o dispositivo está sendo registrado para garantir que as
etapas adequadas sejam feitas.
Entre na opção Registro de Dispositivo pelo método especificado e selecione a opção apropriada para adicionar um
novo dispositivo.
Registre o dispositivo mantendo o botão de registro pressionado até que o registro seja detectado, ou insira o ID do
dispositivo.
Selecione o nº da zona desejada.
Configure os parâmetros necessários do dispositivo.
Monte e teste o detector. Consulte Teste de caminhada /
Teste de diagnóstico local para obter mais informações
sobre como testar o dispositivo. Além disso, consulte o
manual de instalação dos sistemas de alarme nos quais o dispositivo foi registrado para ver outros procedimentos de teste
que são necessários.
OBS.: Se o detector já estiver registrado, você pode configurar os
parâmetros do detector pela programação do sistema. Consulte o
manual de instalação dos sistemas de alarme para obter mais informações sobre os parâmetros do dispositivo.
OBS.: ao registrar o detector PGx972 a painéis sem fio (WP80XX)
com a versão 19.4 ou uma anterior, o detector será registrado como
um detector de movimento, ID 120-xxxx, e identificado como ‘Sensor
de mov’ no painel.
Dicas de Instalação
Use as seguintes dicas como um guia para localizar um local
adequado para a montagem.
Figura 3. Orientações gerais
AVISO! Não obscureça parcialmente nem totalmente o campo de
visão do detector.
AVISO! A fim de obedecer os requisitos de conformidade de
exposição do FCC e ISED Canada RF, o detector PIR deve estar em
uma distância de ao menos 20 cm de qualquer pessoa durante a operação normal. As antenas usadas para este produto não podem estar
colocalizadas ou ser operadas em conjunto com qualquer outra antena
ou transmissor.
OBS.: O PGx872 [[[Undefined variable VariableSetsPortuguese/General.ProductDesc]]] deve ser instalado e
usado dentro de um ambiente que forneça o grau máximo de poluição
2 e sobretensão de categoria II, LOCAIS NÃO PERIGOSOS. O
equipamento foi projetado para ser instalado apenas pelo pessoal qualificado de serviço.
Teste de caminhada / Teste de diagnóstico local
Antes de montar permanentemente qualquer dispositivo sem fio, monte
temporariamente o dispositivo e realize um teste de caminhada. Realize um teste de caminhada da área de cobertura pelo menos uma vez
ao semana para garantir que o detector está funcionando corretamente.
Após colocar a bateria ou fechar o dispositivo, o detector automaticamente entrará em um período de estabilidade em que o LED
VERMELHO piscará por 90 segundos. Faça um teste de caminhada
pela área de cobertura; o LED vermelho piscará cada vez que seu
movimento for detectado seguido por três piscadas de LED. A cor das
três piscadas de LED indica a força do sinal recebido.
A tabela a seguir indica a força do sinal recebido.
Reposta do LED Intensidade do sinal
LED verde pisca
FORTE
LED laranja pisca
BOM
LED vermelho pisca RUIM
Nada pisca
Sem comunicação
IMPORTANTE! Somente são aceitos intensidades de sinal BOA ou
FORTE. Se você receber um sinal RUIM do dispositivo, reposicione-o
e teste novamente até receber um sinal BOM ou FORTE.
OBS.: Para instalações UL/ULC, apenas o nível de sinal FORTE é
aceitável. Após a instalação, verifique a funcionalidade do produto em
conjunto com os painéis de controle compatíveis HSM2HOST9,
HS2LCDRF(P) 9, HS2ICNRF(P)9, PG9920, WS900- 19, and WS900-29.
OBS.: Para obter instruções detalhadas de colocação, consulte o Guia
de referência do painel de controle.
No modo teste de caminhada, independentemente do status de Selação
do LED, o LED acende quando da detecção de qualquer movimento.
Faça o teste de caminhada pela área de cobertura caminhando através
do limite mais distante do padrão de cobertura em ambos os sentidos.
O LED vermelho acende cada vez que seu movimento for detectado
seguido por indicação de força do sinal de LED constante. Depois de
15 minutos, o detector entra automaticamente no modo normal.
Montagem do dispositivo
1.
2.
3.
4.
PGx872 Wireless ceiling PIR presence/security detector Installation Instructions
Marque e perfure dois furos na superfície de montagem. Se
você instalar a proteção contra violação no detector, marque e
perfure um furo para a proteção contra violação e um furo para
um dos outros encaixes disponíveis.
Fixe o suporte à superfície de montagem usando os dois parafusos.
Alinhe as roscas do suporte aos encaixes do detector e gire o
detector em sentido horário. Certifique-se de que está bem
preso.
Fixe o detector ao suporte com o parafuso.
©2018 Tyco Security Products, Toronto, Canada www.dsc.com Tech. Support: 1-800-387-3630
Figura 5. Colocação do detector
A Proteção contra violação
Encaixes de parafuso do
suporte
C Faixa de isolamento
D Roscas do suporte
Figura 6. Fixação do detector E Encaixes do detector
A seguinte tabela resume a distância de detecção em relação à altura
da montagem.
4m
5m
6m
2m
3m
13,1
16,4
19,7
Altura
6,6 pés 9,8 pés
pés
pés
pés
m 3,75 m 4,5 m 6,5 m 10 m
Distância de detecção do 3,1
10,2
12,3
14,8
21,3
32,8
raio
pés
pés
pés
pés
pés
NOTA: Detecção com certificação UL/ULC somente no raio de
11 pés (3,35 m) quando o dispositivo for instalado em uma altura de
9 pés (2,75 m).
Operação do LED
Indicações do LED
LED vermelho pisca
Evento
Estabilização (aquecimento de 90
segundos)
LED vermelho em 0,2 segunAbrir/fechar violação
dos
LED vermelho em 2 segunAlarme de intruso
dos
Para ver instruções sobre como exibir a temperatura de zonas no
painel correto, como medida pelo PGx872, consulte o guia de
instalação do painel.
GERAL
Tipo de detector
Quatro sensores piroelétricos que funcionam em uma configuração
dual separada
ÓTICAS
Dados da lente
Lentes de tipo Fresnel.
Número de feixes: 120
Cobertura máx.
Ø20 m/360° na altura máxima de instalação de 6 m (19,7 pés)
ELÉTRICAS
Fonte de alimentação: Tipo C
Bateria interna
Pilha de lítio de 3 V, tipo CR- 123A. Para instalações de UL, use
apenas Panasonic e GP
Capacidade nominal da pilha: 1450 mAh
Vida útil da bateria (uso típico)
Mínimo de 1 ano. Para uso normal (modo de segurança), 3 anos (não
verificado pelo UL).
Limite de bateria fraca: 2,6 V
OBS.: A incapacidade de se conectar a uma rede sem fio ou a qualidade de uma conexão sem fio inferior a 20% podem diminuir significativamente a expectativa de vida da pilha.
Teste de energia da pilha
Realizado logo após a introdução da pilha e periodicamente em intervalos de algumas horas.
A fonte de alimentação é do tipo C, de acordo com a Documentação
EN 50131-6 — Cláusula 6.
Consumo de corrente
30μA quiescente médio, máximo 150 mA (durante transmissão)
INSTALAÇÃO
Altura: 2 m a 6 m (6,6 - 19,7 ft)
Opções de instalação: Superfície do teto
AMBIENTAIS
Imunidade a RF
De 20 V/m até 1000 MHz, de 10 V/m até 2700 MHz
Temperaturas operacionais
-10 °C a 50 °C (14 °F a 122 °F).
OBS.: A UL verificou somente a operação acima da faixa de 0 °C a
49 °C.
Temperaturas de armazenamento
-20 °C a 60 °C (de - 4 °F a 140 °F)
Umidade
Umidade relativa média de aproximadamente 75% sem condensação.
Por 30 dias por ano, a umidade relativa pode variar de 85% a 95%
sem condensação.
Para instalações de UL: 5% a 93% sem condensação
FÍSICAS
Tamanho (diâmetro): 15 cm
Peso (com bateria): 110 g (3,88 oz)
Cor:
Branca
RECEPTORES COMPATÍVEIS
Este dispositivo pode ser usado com painéis e receptores DSC que
usem a tecnologia PowerG.
OBS.: Apenas os dispositivos operando na faixa de 912-919 MHz são
listados pela UL/ULC.
Europa: CE/EN (EN50131-2-2 GRADE 2, CLASS II, EN50131-6
Tipo C) PG8872: 868 MHz PG4872: 433 MHz.
Figura 7. Distribuidor de feixe a 2,7 m (8.9 pés)
Conforme a EN 50131-1, este equipamento pode ser aplicado em sistemas
instalados até e incluindo o Grau 2 de Segurança, Classe II Ambiental. RU: O
PG8872 é apropriado para uso em sistemas instalados em conformidade com
PD6662 no Grau 2 e classe ambiental 2 BS8243. O periférico Power G tem
uma funcionalidade de comunicação em 2 vias, providenciando benefícios
adicionais descritos na brochura técnica. Esta funcionalidade não foi testada
para estar conforme os respectivos requisitos técnicos e deve, portanto, ser
considerada fora do âmbito da certificação do produto.
Declaração UE de Comformidade Simplificada
O(a) abaixo assinado(a), Tyco Safety Products Canada Ltd declara que o
presente tipo de equipamento de rádio está em conformidade com a Diretiva
2014/53/UE.
O texto integral da declaração de conformidade está disponível no seguinte
endereço de Internet:
PG4872: http://dsc.com/pdf/1710003
PG8872: http://dsc.com/pdf/1710004
Bandes de frequências
Potência máxima
868.0 MHz - 868.6 MHz
10 mW
868.7 MHz - 869.2 MHz
10 mW
Ponto único de contato na Europa: Tyco Safety Products, Voltaweg 20, 6101
XK Echt, Holanda.
D-307204 Rev 0 (08/18)
29010032R001
Figura 8. Distribuidor de feixe a 6 m (19.7 pés)
D-307204
FUNCIONAIS
Verificação de movimentos reais
2 seleções remotas no painel
Tempo de alarme: 2 segundos
SEM FIO
Frequência
Europa e resto do mundo: 433-434 MHz, 868- 869 MHz EUA: 912919 MHz
OBS.: Apenas os dispositivos na faixa de frequência de 915 MHz são
listados pela UL/ULC.
Protocolo de comunicação: PowerG
Supervisão: Sinalização em intervalos de 256 seg
Alerta de violação
Comunicado quando ocorre uma violação e em qualquer mensagem
subsequente até que a chave de violação seja restaurada.
PGx872 Wireless ceiling PIR presence/security detector Installation Instructions
©2018 Tyco Security Products, Toronto, Canada www.dsc.com Tech. Support: 1-800-387-3630

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : 
Create Date                     : 2018:10:12 12:11:54+01:00
Modify Date                     : 2019:02:05 16:02:41+02:00
Subject                         : 
Has XFA                         : No
Language                        : en-us
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Format                          : application/pdf
Creator                         : 
Description                     : 
Title                           : My Document
Metadata Date                   : 2019:02:05 16:02:41+02:00
Keywords                        : 
Producer                        : madbuild
Document ID                     : uuid:31bfcb5e-eb31-43a6-b1c3-c6323647013d
Instance ID                     : uuid:05758d3c-38a2-4ad7-8b3c-3605a28b2404
Page Mode                       : UseOutlines
Page Count                      : 6

EXIF Metadata provided by EXIF.tools