DigitalCom EVE-PLUS-T Wireless Microphone User Manual
DigitalCom Co., Ltd. Wireless Microphone
User Manual
1/16
DigitalCom for EVE PLUS
USERS MANUAL
WIRELESS MICROPHONE
EVE PLUS T
DigitalCom Co., Ltd.
2/16
1 Packing List and Optional Accessories
* Check that your package contains all the components listed for your system below. If anything is
missing, please contact the shop you purchased.
Systems and Components
Accessories
3/16
2 General
Introduction
WIRELESS MICROPHONE Series dual channel microphone set, gives you freedom to perform up to
12 hours once fully charged. It delivers superior durability against abuse use, and gives an extreme
convenience to installers because of pre-tuned crystal clear sound quality with minimal and tiny
mechanics.
The battery level & channel in use indicating on FND give users a high-level usability, and also the
multi-colored LED alerts enable to distinguish low battery & proper channel pairing. It works with the
less-crowded UHF frequency band, giving you clearer interference-free sound.
WIRELESS MICROPHONE Series channel allocation makes sure of superior sound quality, operating
up to 12 channels simultaneously in case of 12 MHz bandwidth. Both mic channels have their own
volume control and you can either output both channels independently or together using the
"mixed output". An auto mute circuit eliminates the popping noise when switching the unit
on or off.
Our system is designed and manufactured to be dependable, problem free, versatile and easy to
use.
> Field proven durable design against abuse use
> CONIC patented multi-tone decoding function for anti-interference
> CONIC patented pop noise reduction when power on or off
> Displaying channel in use & battery level
> Link status indicating
> Easy to fix out a channel by digital buttons
> Automatic channel sync between charger and handheld transmitter
> Semi-automatic frequncy lock-out function
> Easy to install with fixtures
EVE PLUS Dual Channel Receiver with Charger
Front Panel
Rear Panel
4/16
Volume Knobs (VOL1, VOL2) ①- Adjust volume for audio
Channel Dis②play - Display current channel that is being used
Link Display ③- Display connecting (working) condition between microphone and receiver (Shows
green light under normal state)
Power ④- Power On/Off switch for receiver
Lock Switch ⑤- To change the channel, ‘Lock Switch’ should be sited on UNLOCK.
To prevent unwanted channel change, place ‘Lock Switch’ on LOCK.
Channel ⑥UP/DOWN Switch (MIC1, MIC2)
Microphone Output Port⑦ (Output1, Output2) - Audio signal output port which is connected by
each 1/4 inch audio cable of microphone 1 and 2
Microphone Output(Output1+2) ⑧- Audio signal output port which is connected by 1/4 inch audio
cable for combined audio signal of each microphone 1 and 2
⑨Power Socket - Power supply socket (DC 12V)
⑩Gain Adjustment
⑪Antenna terminal
Handheld Transmitter
EVE PLUS T
1. Sound Inlet Basket
The guard net to protect unit which is a component to transform voice to electrical digital tone.
2. Power Switch
Power On/Off switch
3. Power LED
It shows power supply condition. Red is normal state. If the light keeps blinking, please recharge it
before using.
4. Charging Terminals
CHARGE TERMINAL : Terminal to recharge microphone.
5/16
Charger
EVE PLUS C
4. Adaptor Jack
Push supplied adaptor into this socket. (DC12V 1A)
5. Charging Door
Holes to charge microphone.
6/16
3 Setting Up
• Prior to setting up your WIRELESS SYSTEM, check that the transmitter and receiver are tuned to
the same frequency, referring to sections 3.8 and 3.9.
Receiver
Single Receiver
1. Unscrew the four rubber feet (1) from the receiver bottom panel.
2. Unscrew the two fixing screws (2) from each side panel.
3. Use the fixing screws (2) to screw the short bracket 3 to one side panel and the long bracket (4)
to the other side panel. The brackets are contained in the supplied rack mounting kit.
4. Install the receiver in your rack.
Two Receivers Side by Side
1. Unscrew the four rubber feet (1) from each receiver's bottom panel and remove the screws (5)
from the rubber feet (1).
2. Unscrew the two fixing screws (2) from the right-hand side panel of one receiver and from the
left-hand side panel of the other receiver.
3. Fix the connecting strips (4) on the first receiver using the screws (5) you removed from the rubber
feet.
4. To join the two receivers, slide the connecting strips (4) on the first receiver through the free slots
in the side panel of the second receiver. Make sure to align the hole in each connecting strip (4)
with the appropriate threaded hole in the bottom panel of the second receiver.
5. Fix the connecting strips (4) on the second receiver using the screws (5) you removed from the
rubber feet (1).
6. Screw a short bracket (6) to the outer side panel of each receiver using for each bracket two of
the screws (2) you removed from the receiver side panels.
7. Install the receivers in your rack.
Positioning the Receiver
Reflections off metal parts, walls, ceilings, etc. or the shadow effects of musicians and other people
may weaken or cancel the direct transmitter signal.
For best results, place the receiver or remote antennas as follows:
• Place the receiver/antennas near the performance area (stage). Make sure, though, that the
transmitter will never get any closer to the receiver than 10 ft (3 m).
• Check that you can see the receiver from where you will be using the transmitter.
• Place the receiver at least 5 ft. (1.5 m) away from any big metal objects, walls, scaffolding,
ceilings, etc.
• You can either use the receiver freestanding or mount it in a 19" rack using the supplied Rack
Mount Kit.
• If you install one or ore receivers into a 19" rack, either mount the supplied antennas on the
7/16
receiver front panel(s) or use remote antennas. This is the only way to ensure optimum reception
quality.
Connecting the Receiver to a Mixer / Amplifier
You can use both the XLR and ¼” jack outputs to connect the receiver to your mixer or amp. Use
the receiver’s AUDIO Menu to adjust the output level as required.
• Connect the audio output to the desired input:
- XLR output -> XLR Cable -> XLR input
- 1/4” output -> unbalanced cable -> ¼" input
Connecting the Receiver to Power
1. CAUTION: Check that the AC mains voltage stated on the included power supply is identical to
the AC mains voltage available where you will use your system.
Using the power supply with a different AC voltage may cause damage to the unit.
2. Plug the feeder cable (1) on the included power supply into the DC IN socket (2) on the receiver
rear panel.
3. Plug the power supply into a convenient power outlet.
LOCK Mode
The receiver is electronically locked so that you cannot make any unintended adjustments.
The "LOCK/UNLOCK" switch is placed on the bottom of the receiver or in the front panel.
• To enter SETUP mode, slide it left or right to "UNLOCK"
8/16
Charger
Mounting on/in the wall or shelf.
1. Slide the fixtures into the charger to mount on/in a shelf or wall.
2. CAUTION: Check that the AC mains voltage stated on the included power supply
is identical to the AC mains voltage available where you will use your system.
Using the power supply with a different AC voltage may cause damage to the unit.
3. Plug the feeder cable (1) on the included power supply into the DC IN socket (2) on the charger
rear panel.
4. Plug the power supply into a convenient power outlet.
9/16
4 Operating Notes
Setting Up a Channel in Use
* Wireless Microphones have an innovative function that is the automatic sync between charger
and handheld's.
1. Find out the 5-digit piano and the slide switch at the bottom of the charger.
2. Slide right or left to unlock.
3. Put the 5-digit piano switch properly according to the "CHANNEL ALLOCATION TABLE" label. 30
pair of frequencies will be available by different combination of the 5-digit piano switch. each MIC
will be synced up automatically when it is inserted into the charger only when the “LOCK/UNLOCK”
switch is positioned to “UNLOCK”.
4. Slide right or left to LOCK in the charger once each MIC has been synced up. Otherwise it could
make an unwanted interference that two handheld’s could have same channel in use.
5. Press the front panel POWER key to switch power to the receiver ON.
10/16
6. The display will indicate the currently active channel.
7. Please make sure the receiver is in the LOCK mode. And slide left or right to UNLOCK to change a
pair of channels in use.
8. Press the keys, “DOWN” and “UP” to match a pair of channels on the front panel of the receiver.
9. Slide right or left to LOCK in the receiver after channel setting-up.
* Please follow up the above procedures even in case a MIC should be replaced to new one or a
channel in use must be changed.
11/16
Maintenance of MIC Cartridge Capsule and Battery in Handheld
Loosen the hexagon head bolt with using the built①-in L wrench in the right below the sound inlet
basket and unscrew the sound inlet basket up
Pull up the microphone cartridge smoothly with turning left②
Separate the friction / ③positive lock from the wire connector
④ Screw out the battery compartment bolt and remove the battery compartment
⑤Pull out the battery connector from the internal holder and remove the battery pack
⑥ Insert new battery pack and do same job in the reverse sequence.
5 Microphone Technique
Handheld Transmitter A handheld vocal microphone provides many ways of shaping the sound
of your voice as it is heard over the sound system.
The following sections contain useful hints on how to use your handheld
transmitter for best results.
Working Distance and
Proximity Effect
Basically, your voice will sound the bigger and mellower, the closer you
hold the microphone to your lips. Moving away from the microphone will
produce a more reverberant, more distant sound, as the microphone will
pick more of the room’s reverberation.
You can use this effect to make your voice sound aggressive, neutral,
insinuating, etc. simply by changing your working distance.
Proximity effect is a more or less dramatic boost of low frequencies that
occurs when you sing into the microphone from less than 2 inches. It gives
more "body" to your voice and an intimate, bass-heavy sound.
12/16
Angle of Incidence Sing to one side of the microphone or above and across the
microphone’s top. This provides a well-balanced, natural sound.
If you sing directly into the microphone, it will not only pick up excessive
breath noise but also overemphasize "sss", "sh", "tch", "p", and "t" sounds.
Feedback Feedback is the result of part of the sound projected by a speaker being
picked up by a microphone, fed to the amplifier, and projected again by
the speaker. Above a specific volume or "system gain" setting called the
feedback threshold, the signal starts being regenerated indefinitely,
making the sound system howl and the sound engineer desperately dive
for the master fader to reduce the volume and stop the howling.
To increase usable gain before feedback, place the main ("FOH")
speakers in front of the microphones (along the front edge of the stage).
If you use monitor speakers, be sure never to point any microphone
directly at the monitors.
Feedback may also be triggered by resonances depending on the
acoustics of the room or hall. With resonances at low frequencies,
proximity effect may cause feedback. In this case, it is often enough to
move away from the microphone a little to stop the feedback.
Backling Choir 1. Never let more than two persons share a microphone.
2. Ask your backing vocalists never to sing more than 35 degrees off the
microphone axis.
The microphone is very insensitive to off-axis sounds. If the two vocalists
were to sing into the microphone from a wider angle than 35 degrees, you
may end up bringing up the fader of the microphone channel far enough
to create a feedback problem.
13/16
6 Troubleshooting
Problem Possible Cause Remedy
No sound. 1. AC adapter is not connected to receiver
and/or power outlet.
2. Receiver is OFF.
3. Receiver is not connected to mixer or
amplifier.
4. Microphone or instrument is not connected
to bodypack transmitter.
5. Transmitter is tuned to different frequency
than receiver.
6. Transmitter is "OFF" or transmitter MUTE
switch at "MUTE".
7. Transmitter batteries are not inserted
properly.
8. Transmitter batteries/battery pack dead.
9. Transmitter is too far away from receiver or
squelch threshold setting is too high.
10. Obstructions between transmitter and
receiver.
11. Receiver is invisible from transmitter
location.
12. Receiver too close to metal objects.
13. Transmitter and receiver Preset versions are
not identical.
1. Connect AC adapter to receiver and/or
power outlet.
2. Push POWER switch to switch receiver ON.
3. Connect receiver output to mixer or
amplifier input.
4. Connect microphone or instrument to audio
input on
bodypack.
5. Tune transmitter and receiver to the same
frequency.
6. Switch transmitter "ON" or set MUTE switch
to ”ON”
position.
7. Insert batteries conforming to "+" and "-"
marks.
8. Replace batteries/charge battery pack.
9. Move closer to receiver or choose lower
squelch threshold setting.
10. Remove obstructions.
11. Avoid spots where you cannot see
receiver.
12. Remove offending objects or move
receiver away.
13. Check Preset versions on transmitter and
receiver.
Noise, crackling,
unwanted signals.
1. Antenna location.
2. Interference from other wireless systems, TV,
radio, CB radios, or defective electrical
appliances or installations.
1. Relocate receiver or antennas.
2. Switch off interference sources or defective
appliances or tune transmitter and receiver to
a different frequency; have electrical
installation checked.
Distortion. 1. GAIN control on transmitter is set too high or
too low.
2. Interference from other wireless systems, TV,
radio, CB radios, or defective electrical
appliances or installations.
1. Decrease or increase GAIN setting just
enough to stop the distortion.
2. Switch off interference sources or defective
appliances or tune transmitter and receiver to
a different frequency; have electrical
installation checked.
Momentary loss of sound
("dropouts") at some points
within performance area.
* Antenna location. * Relocate receiver or antennas. If dead spots
persist, mark and avoid them.
14/16
7 Specifications
Receiver
Overall Dimensions
Net Weight
Audio Output Level
Output Impedance
RF Sensitivity
Adjacent Channel Rejection
Intermodulation
Image Rejection
Spurious Rejection
Antenna
Power Requirements
Power Consumption
40 mm H x 234 mm W x 160 mm D (1.57 x 9.21 x 6.3 i
813 g (28.68 oz)
¼ in.: -8 ~ +0 dBu (1 kHz, @+/-50 kHz)
600 Ω (600 Ω, 6.3 mm / ¼ in. connector)
-88 dBm for 40 dB SINAD
> 60 dB
> 70 dB
110 dB typical
90 dB typical
λ/4 Herical
12 V DC / 1 A [with DC power adapter]
< 10 W
Transmitter
Gain Adjustment Range
Deviation
Input Impedance
Output Impedance
Antenna
RF Power Output
Connector Types
Power Requirements
Battery Life
Overall Dimensions
Net Weight
n/a
+/- 50 kHz max.
n/a
50 Ω
Intenna
10 mW
n/a
Rechargeable Lithuim Polymer battery, 3.7 V / 850 mA
12 hours typical
246 mm H x 55 mm Upper π x 34 mm Bottom π (9.68 x 2.2 x 1.34 .i)n
Upper π x 34 mm Bottom π (9.68 x 2.2 x 1.34 .i)n
235 g (8.29 oz)
Charger
Power Requirements
Current Consumption
Channel Configuration
Overall Dimensions
Net Weight
5 V DC / 1 A [with DC power adapter]
< 700 mA
Digital buttons10 mW or 50 mW (region dependent)
75 mm H x 157 mm W x 99 mm D (2.95 x 6.18 x 3.89 in.)
240 g (8.45 oz)
9 Limited Warranty
DigitalCom warrants to the original consumer of Conic products that the product will be free of defects in
materials and/or workmanship for the periods indicated. This warranty is applicable to all Conic models and
only in the fifty (50) United States;
Warranty : 1 year / Spare parts : 1 year
15/16
LIMITED WARRANTY
If during the first 1 year that immediately follows the purchase date, your new Conic products are covered by
this warranty and Conic and/or its authorized service center will repair or replace the defective part without
charge for parts or labor.
DigitalCom reserves the right to utilize reconditioned parts in repairing these products and/or to use
reconditioned units as warranty replacements.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY WHICH DIGITALCOM MAKES IN
CONNECTION WITH THESE PRODUCTS. ANY IMPLIED WARRANTY APPLICABLE TO THE
PRODUCT, INCLUDING THE WARRANTY OF MERCHANT ABILITY IS LIMITED TO THE DURATION
OF THE EXPRESS WARRANTY. DIGITALCOM EXCLUDES AND SHALL NOT BE LIABLE IN ANY
EVENTS FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow limitations that relate to implied warranties and/or the exclusion of incidental or
consequential damages. Therefore, these limitations and exclusions may not apply to you. This warranty gives
you specific -legal rights. You may also have other rights which vary from state to state.
CONSUMER RESPONSIBILITIES
If warranty service should be required, it is necessary that the consumer assume certain responsibilities.
1. You must complete and return warranty registration card to DigitalCom customer service department.
2. Contact DigitalCom Customer Service ( 82-32-624-1980) for a Return Authorization Number (RA#).
3. Return your product to DigitalCom or an authorized service center with proof of purchase (sales receipt,
etc.), RA# and detail description of the problem(s).
4. Shipping and/or insurance costs are the consumer's responsibility. DigitalCom is NOT responsible for shipping
costs either from or to the consumer.
5. Units shipped for service should be packed securely. It is recommended to use the original box for the
product and double box it to avoid shipping damage. DigitalCom is NOT responsible for any damage during
shipping.
6. Your owner's manual contains important safety and operating instructions. It is your responsibility to be
aware of the contents of the manual and to follow all safety precautions.
EXCLUSIONS
This limited warranty provided by DigitalCom does not cover;
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence,
misuse, faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service
facility authorized by DigitalCom to render such service, or if affixed any attachment not provided with the
products, or if the model number or serial number has been altered, tampered with, defaced or removed.
2. Initial installation and removal for repair.
3. Shipping costs to Mediasync or authorized service center for repair service.
4. Shipping costs to return the repaired product to customer.
5. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head
cleaning.
6. Damage that occurs in shipment, due to act of God, and cosmetic damage.
7. Accessories and batteries
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
con-nected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation
Information to user.
The users manual or instruction manual for an intentional or unintentional radiator shall caution
the user that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment. In cases where the manual
is provided only in a form other than paper, such as on a computer disk or over the Internet, the
information required by this section may be included in the manual in that alternative form,
provided the user can reasonably beexpected to have the capability to access information in
that form.
IMPORTANT NOTE:
IMPORTANT Safety Instruction:
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this equipment near water.
6) Do not using near any heat sources such as radiators, heat resisters, stove, or other
equipment that produce heat.
European CE notice to users and product statements
This product is CE marked according to the provisions of the R&TTE
Directive(99/5/EC). Hereby, Digitalcom Co., Ltd. declares that this product
is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
For further information, please contact http:// www.digitalcoms.net
Digitalcom Co., Ltd.
303-801 Bucheon Techno Park Ssangyong 3 Cha Apt, 397, Seokcheon-ro,
Ojeong-gu, Bucheon-si 421-742, Korea
Tel: +82-32-624-1980 / Fax: +82-32-624-1985
URL: www.digitalcoms.net
CONTACT INFORMATION
Manufacturer Address : 303-801 Bucheon Techno Park Ssangyong 3 Cha Apt, 397, Seokcheon-ro, Ojeong-gu,
Bucheon-si 421-742, Korea
To locate in-country Digitalcom Co., Ltd., distributors of the Wireless Microphone please refer to the Digitalcom
Co., Ltd. Website http://www.digitalcoms.net
These distributor(s) represent local contacts for this product.
CORPORATE HEADQUARTERS:
Digitalcom Co., Ltd.
303-801 Bucheon Techno Park Ssangyong 3 Cha Apt, 397, Seokcheon-ro, Ojeong-gu,
Bucheon-si 421-742, Korea
Tel: +82-32-624-1980
Fax: +82-32-624-1985
Web: http:// www.digitalcoms.net
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is Subject to the following two condition: (1) this device may not cause interference
,and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
EUROPEAN UNION “DECLARATION OF CONFORMITY”
DECLARATION OF CONFORMITY
Digitalcom Co., Ltd.
303-801 Bucheon Techno Park Ssangyong 3 Cha Apt, 397, Seokcheon-ro, Ojeong-gu,
Bucheon-si 421-742, Korea
declare under our sole responsibility that the product(s)
Wireless Microphone – EVE PLUS T
to which this declaration relate(s) is in conformance with the following standards:
EN 301 489-1 V1.9.2:2011
EN 301 489-3 V1.5.1:2012
EN60950-1:2006+A12:2012
EN 300 220-1 V2.4.11:2012
EN 300 220-2 V2.4.11:2012
following the provisions of the 1999/5/EC Directives.
16/16
CUSTOMER SERVICE
DigitalCom
#801, 303-dong, Bucheon Technopark, SSANGYONG III, 36-1, Samjeong-dong, Ojeong-gu, Bucheon-city,
Gyeonggi-do, Korea
Tel : 82-32-624-1980 (Ext.680)
Fax:82-32-624-1986
Email : sales@digitalcoms.net
Homepage: http://www.conics.co.kr/en.html
Please keep the sales receipt and owner's manual with this document.